Peter Zijlstra [Fri, 11 Apr 2014 07:59:17 +0000 (09:59 +0200)]
sched/idle, alpha: Switch from TS_POLLING to TIF_POLLING_NRFLAG
Standardize the idle polling indicator to TIF_POLLING_NRFLAG such that
both TIF_NEED_RESCHED and TIF_POLLING_NRFLAG are in the same word.
This will allow us, using fetch_or(), to both set NEED_RESCHED and
check for POLLING_NRFLAG in a single operation and avoid pointless
wakeups.
Changing from the non-atomic thread_info::status flags to the atomic
thread_info::flags shouldn't be a big issue since most polling state
changes were followed/preceded by a full memory barrier anyway.
Signed-off-by: Peter Zijlstra <peterz@infradead.org> Acked-by: Richard Henderson <rth@twiddle.net> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matt Turner <mattst88@gmail.com> Cc: Richard Henderson <rth@twiddle.net> Cc: 蔡正龙 <zhenglong.cai@cs2c.com.cn> Cc: linux-alpha@vger.kernel.org Link: http://lkml.kernel.org/n/tip-9tfzr196gs0n2afxv0ga8pc3@git.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jason Low [Thu, 24 Apr 2014 01:30:35 +0000 (18:30 -0700)]
sched/fair: Stop searching for tasks in newidle balance if there are runnable tasks
It was found that when running some workloads (such as AIM7) on large
systems with many cores, CPUs do not remain idle for long. Thus, tasks
can wake/get enqueued while doing idle balancing.
In this patch, while traversing the domains in idle balance, in
addition to checking for pulled_task, we add an extra check for
this_rq->nr_running for determining if we should stop searching for
tasks to pull. If there are runnable tasks on this rq, then we will
stop traversing the domains. This reduces the chance that idle balance
delays a task from running.
This patch resulted in approximately a 6% performance improvement when
running a Java Server workload on an 8 socket machine.
Vincent Guittot [Fri, 11 Apr 2014 09:44:40 +0000 (11:44 +0200)]
sched: Add a new SD_SHARE_POWERDOMAIN for sched_domain
A new flag SD_SHARE_POWERDOMAIN is created to reflect whether groups of CPUs
in a sched_domain level can or not reach different power state. As an example,
the flag should be cleared at CPU level if groups of cores can be power gated
independently. This information can be used in the load balance decision or to
add load balancing level between group of CPUs that can power gate
independantly.
This flag is part of the topology flags that can be set by arch.
Vincent Guittot [Fri, 11 Apr 2014 09:44:37 +0000 (11:44 +0200)]
sched: Rework sched_domain topology definition
We replace the old way to configure the scheduler topology with a new method
which enables a platform to declare additionnal level (if needed).
We still have a default topology table definition that can be used by platform
that don't want more level than the SMT, MC, CPU and NUMA ones. This table can
be overwritten by an arch which either wants to add new level where a load
balance make sense like BOOK or powergating level or wants to change the flags
configuration of some levels.
For each level, we need a function pointer that returns cpumask for each cpu,
a function pointer that returns the flags for the level and a name. Only flags
that describe topology, can be set by an architecture. The current topology
flags are:
Then, each level must be a subset on the next one. The build sequence of the
sched_domain will take care of removing useless levels like those with 1 CPU
and those with the same CPU span and no more relevant information for
load balancing than its children.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org> Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com> Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com> Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: David S. Miller <davem@davemloft.net> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Hanjun Guo <hanjun.guo@linaro.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Jason Low <jason.low2@hp.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Tony Luck <tony.luck@intel.com> Cc: linux390@de.ibm.com Cc: linux-ia64@vger.kernel.org Cc: linux-s390@vger.kernel.org Link: http://lkml.kernel.org/r/1397209481-28542-2-git-send-email-vincent.guittot@linaro.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Changing PTEs and PMDs to pte_numa & pmd_numa is done with the
mmap_sem held for reading, which means a pmd can be instantiated
and turned into a numa one while __handle_mm_fault() is examining
the value of old_pmd.
If that happens, __handle_mm_fault() should just return and let
the page fault retry, instead of throwing an oops. This is
handled by the test for pmd_trans_huge(*pmd) below.
Signed-off-by: Rik van Riel <riel@redhat.com> Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Reported-by: Sunil Pandey <sunil.k.pandey@intel.com> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mel Gorman <mgorman@suse.de> Cc: linux-mm@kvack.org Cc: lwoodman@redhat.com Cc: dave.hansen@intel.com Link: http://lkml.kernel.org/r/20140429153615.2d72098e@annuminas.surriel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
sched/numa: Do not set preferred_node on migration to a second choice node
Setting the numa_preferred_node for a task in task_numa_migrate
does nothing on a 2-node system. Either we migrate to the node
that already was our preferred node, or we stay where we were.
On a 4-node system, it can slightly decrease overhead, by not
calling the NUMA code as much. Since every node tends to be
directly connected to every other node, running on the wrong
node for a while does not do much damage.
However, on an 8 node system, there are far more bad nodes
than there are good ones, and pretending that a second choice
is actually the preferred node can greatly delay, or even
prevent, a workload from converging.
The only time we can safely pretend that a second choice
node is the preferred node is when the task is part of a
workload that spans multiple NUMA nodes.
sched/numa: Retry placement more frequently when misplaced
When tasks have not converged on their preferred nodes yet, we want
to retry fairly often, to make sure we do not migrate a task's memory
to an undesirable location, only to have to move it again later.
This patch reduces the interval at which migration is retried,
when the task's numa_scan_period is small.
The NUMA code is smart enough to distribute the memory of workloads
that span multiple NUMA nodes across those NUMA nodes.
However, it still has a pretty high scan rate for such workloads,
because any memory that is left on a node other than the node of
the CPU that faulted on the memory is counted as non-local, which
causes the scan rate to go up.
Counting the memory on any node where the task's numa group is
actively running as local, allows the scan rate to slow down
once the application is settled in.
This should reduce the overhead of the automatic NUMA placement
code, when a workload spans multiple NUMA nodes.
Jason Low [Mon, 28 Apr 2014 22:45:54 +0000 (15:45 -0700)]
sched: Fix updating rq->max_idle_balance_cost and rq->next_balance in idle_balance()
The following commit:
e5fc66119ec9 ("sched: Fix race in idle_balance()")
can potentially cause rq->max_idle_balance_cost to not be updated,
even when load_balance(NEWLY_IDLE) is attempted and the per-sd
max cost value is updated.
Preeti noticed a similar issue with updating rq->next_balance.
In this patch, we fix this by making sure we still check/update those values
even if a task gets enqueued while browsing the domains.
Peter Zijlstra [Thu, 24 Apr 2014 10:00:47 +0000 (12:00 +0200)]
sched: Skip double execution of pick_next_task_fair()
Tim wrote:
"The current code will call pick_next_task_fair a second time in the
slow path if we did not pull any task in our first try. This is
really unnecessary as we already know no task can be pulled and it
doubles the delay for the cpu to enter idle.
We instrumented some network workloads and that saw that
pick_next_task_fair is frequently called twice before a cpu enters
idle. The call to pick_next_task_fair can add non trivial latency as
it calls load_balance which runs find_busiest_group on an hierarchy of
sched domains spanning the cpus for a large system. For some 4 socket
systems, we saw almost 0.25 msec spent per call of pick_next_task_fair
before a cpu can be idled."
Optimize the second call away for the common case and document the
dependency.
Reported-by: Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Len Brown <len.brown@intel.com> Link: http://lkml.kernel.org/r/20140424100047.GP11096@twins.programming.kicks-ass.net Signed-off-by: Ingo Molnar <mingo@kernel.org>
sched: Use CPUPRI_NR_PRIORITIES instead of MAX_RT_PRIO in cpupri check
The check at the beginning of cpupri_find() makes sure that the task_pri
variable does not exceed the cp->pri_to_cpu array length. But that length
is CPUPRI_NR_PRIORITIES not MAX_RT_PRIO, where it will miss the last two
priorities in that array.
As task_pri is computed from convert_prio() which should never be bigger
than CPUPRI_NR_PRIORITIES, if the check should cause a panic if it is
hit.
Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1397015410.5212.13.camel@marge.simpson.net Signed-off-by: Ingo Molnar <mingo@kernel.org>
Juri Lelli [Tue, 15 Apr 2014 11:49:04 +0000 (13:49 +0200)]
sched/deadline: Fix sched_yield() behavior
yield_task_dl() is broken:
o it forces current to be throttled setting its runtime to zero;
o it sets current's dl_se->dl_new to one, expecting that dl_task_timer()
will queue it back with proper parameters at replenish time.
Unfortunately, dl_task_timer() has this check at the very beginning:
if (!dl_task(p) || dl_se->dl_new)
goto unlock;
So, it just bails out and the task is never replenished. It actually
yielded forever.
To fix this, introduce a new flag indicating that the task properly yielded
the CPU before its current runtime expired. While this is a little overdoing
at the moment, the flag would be useful in the future to discriminate between
"good" jobs (of which remaining runtime could be reclaimed, i.e. recycled)
and "bad" jobs (for which dl_throttled task has been set) that needed to be
stopped.
Thomas Gleixner [Fri, 2 May 2014 21:26:24 +0000 (23:26 +0200)]
sched: Sanitize irq accounting madness
Russell reported, that irqtime_account_idle_ticks() takes ages due to:
for (i = 0; i < ticks; i++)
irqtime_account_process_tick(current, 0, rq);
It's sad, that this code was written way _AFTER_ the NOHZ idle
functionality was available. I charge myself guitly for not paying
attention when that crap got merged with commit abb74cefa ("sched:
Export ns irqtimes through /proc/stat")
So instead of looping nr_ticks times just apply the whole thing at
once.
As a side note: The whole cputime_t vs. u64 business in that context
wants to be cleaned up as well. There is no point in having all these
back and forth conversions. Lets standardise on u64 nsec for all
kernel internal accounting and be done with it. Everything else does
not make sense at all for fine grained accounting. Frederic, can you
please take care of that?
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Cc: Venkatesh Pallipadi <venki@google.com> Cc: Shaun Ruffell <sruffell@digium.com> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1405022307000.6261@ionos.tec.linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
sched/docbook: Fix 'make htmldocs' warnings caused by missing description
When 'flags' argument to sched_{set,get}attr() syscalls were
added in:
6d35ab48090b ("sched: Add 'flags' argument to sched_{set,get}attr() syscalls")
no description for 'flags' was added. It causes the following warnings on "make htmldocs":
Warning(/kernel/sched/core.c:3645): No description found for parameter 'flags'
Warning(/kernel/sched/core.c:3789): No description found for parameter 'flags'
Merge tag 'gpio-v3.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
"A small batch of GPIO fixes for the v3.15 series. I expect more to
come in but I'm a bit behind on mail, might as well get these to you
right now:
- Change a crucial semantic ordering in the GPIO irqchip helpers
- Fix two nasty regressions in the ACPI gpiolib extensions"
* tag 'gpio-v3.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio / ACPI: Prevent potential wrap of GPIO value on OpRegion read
gpio / ACPI: Don't crash on NULL chip->dev
gpio: set data first, then chip and handler
Merge branch 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 vdso fix from Peter Anvin:
"This is a single build fix for building with gold as opposed to GNU
ld. It got queued up separately and was expected to be pushed during
the merge window, but it got left behind"
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, vdso: Make the vdso linker script compatible with Gold
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"These are regression and bug fixes for ext4.
We had a number of new features in ext4 during this merge window
(ZERO_RANGE and COLLAPSE_RANGE fallocate modes, renameat, etc.) so
there were many more regression and bug fixes this time around. It
didn't help that xfstests hadn't been fully updated to fully stress
test COLLAPSE_RANGE until after -rc1"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (31 commits)
ext4: disable COLLAPSE_RANGE for bigalloc
ext4: fix COLLAPSE_RANGE failure with 1KB block size
ext4: use EINVAL if not a regular file in ext4_collapse_range()
ext4: enforce we are operating on a regular file in ext4_zero_range()
ext4: fix extent merging in ext4_ext_shift_path_extents()
ext4: discard preallocations after removing space
ext4: no need to truncate pagecache twice in collapse range
ext4: fix removing status extents in ext4_collapse_range()
ext4: use filemap_write_and_wait_range() correctly in collapse range
ext4: use truncate_pagecache() in collapse range
ext4: remove temporary shim used to merge COLLAPSE_RANGE and ZERO_RANGE
ext4: fix ext4_count_free_clusters() with EXT4FS_DEBUG and bigalloc enabled
ext4: always check ext4_ext_find_extent result
ext4: fix error handling in ext4_ext_shift_extents
ext4: silence sparse check warning for function ext4_trim_extent
ext4: COLLAPSE_RANGE only works on extent-based files
ext4: fix byte order problems introduced by the COLLAPSE_RANGE patches
ext4: use i_size_read in ext4_unaligned_aio()
fs: disallow all fallocate operation on active swapfile
fs: move falloc collapse range check into the filesystem methods
...
Anton Ivanov [Fri, 7 Mar 2014 18:37:47 +0000 (18:37 +0000)]
um: Memory corruption on startup
The reverse case of this race (you must msync before read) is
well known. This is the not so common one.
It can be triggered only on systems which do a lot of task
switching and only at UML startup. If you are starting 200+ UMLs
~ 0.5% will always die without this fix.
Signed-off-by: Anton Ivanov <antivano@cisco.com>
[rw: minor whitespace fixes] Signed-off-by: Richard Weinberger <richard@nod.at>
Anton Ivanov [Fri, 7 Mar 2014 18:37:46 +0000 (18:37 +0000)]
um: Missing pipe handling
UML does not handle sigpipe. As a result when running it under
expect or redirecting the IO from the console to an external program
it will crash if the program stops or exits.
Signed-off-by: Anton Ivanov <antivano@cisco.com> Signed-off-by: Richard Weinberger <richard@nod.at>
Inferring the mount hierarchy correctly from /proc/mounts is hard when MS_MOVE
may have been used, and the previous code did it wrongly. This change simplifies
the logic to only require that /dev/shm be _on_ tmpfs (which can be checked
trivially with statfs) rather than that it be a _mountpoint_ of tmpfs, since
there isn't a compelling reason to be that strict. We also now check for tmpfs
on whatever directory we ultimately use so that the user is better informed.
This change also moves the more standard TMPDIR environment variable check ahead
of the others.
Applies to 3.12.
Signed-off-by: Tristan Schmelcher <tschmelcher@google.com> Signed-off-by: Richard Weinberger <richard@nod.at>
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine fixes from Vinod Koul:
"Back from long weekend here in India and now the time to send fixes
for slave dmaengine.
- Dan's fix of sirf xlate code
- Jean's fix for timberland
- edma fixes by Sekhar for SG handling and Yuan for changing init
call"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: fix eDMA driver as a subsys_initcall
dmaengine: sirf: off by one in of_dma_sirfsoc_xlate()
platform: Fix timberdale dependencies
dma: edma: fix incorrect SG list handling
Merge tag 'iommu-fixes-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"Fixes for regressions:
- fix wrong IOMMU enumeration causing some SCSI device drivers
initialization failures
- ARM-SMMU fixes for a panic condition and a wrong return value"
* tag 'iommu-fixes-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/arm-smmu: fix panic in arm_smmu_alloc_init_pte
iommu/arm-smmu: Return 0 on unmap failure
iommu/vt-d: fix bug in matching PCI devices with DRHD/RMRR descriptors
iommu/vt-d: Fix get_domain_for_dev() handling of upstream PCIe bridges
iommu/vt-d: fix memory leakage caused by commit ea8ea46
Adrien BAK [Fri, 18 Apr 2014 02:00:43 +0000 (11:00 +0900)]
perf tools: Improve error reporting
In the current version, when using perf record, if something goes
wrong in tools/perf/builtin-record.c:375
session = perf_session__new(file, false, NULL);
The error message:
"Not enough memory for reading per file header"
is issued. This error message seems to be outdated and is not very
helpful. This patch proposes to replace this error message by
"Perf session creation failed"
I believe this issue has been brought to lkml:
https://lkml.org/lkml/2014/2/24/458
although this patch only tackles a (small) part of the issue.
Additionnaly, this patch improves error reporting in
tools/perf/util/data.c open_file_write.
Currently, if the call to open fails, the user is unaware of it.
This patch logs the error, before returning the error code to
the caller.
Reported-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Adrien BAK <adrien.bak@metascale.org> Link: http://lkml.kernel.org/r/1397786443.3093.4.camel@beast
[ Reorganize the changelog into paragraphs ]
[ Added empty line after fd declaration in open_file_write ] Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Vladimir Nikulichev <nvs@tbricks.com> Tested-by: Namhyung Kim <namhyung@kernel.org> Reviewed-by: Adrian Hunter <adrian.hunter@intel.com> Link: http://lkml.kernel.org/r/969812.163009436-sendEmail@nvs Signed-off-by: Jiri Olsa <jolsa@redhat.com>
perf kvm: Fix 'Min time' counting in report command
Every event in the perf-kvm has a 'stats' structure, which contains
max/min/average/etc times of handling this event.
The problem is that the 'perf-kvm stat report' command always shows
that 'min time' is 0us for every event. Example:
This happens because the 'stats' structure is not initialized and
stats->min equals to 0. Lets initialize the structure for every
event after its allocation using init_stats() function. This initializes
stats->min to -1 and makes 'Min time' statistics counting work:
Once COLLAPSE RANGE is be disable for ext4 with bigalloc feature till finding
root-cause of problem. It will be enable with fixing that regression of
xfstest(generic 075 and 091) again.
ext4: fix COLLAPSE_RANGE failure with 1KB block size
When formatting with 1KB or 2KB(not aligned with PAGE SIZE) block
size, xfstests generic/075 and 091 are failing. The offset supplied to
function truncate_pagecache_range is block size aligned. In this
function start offset is re-aligned to PAGE_SIZE by rounding_up to the
next page boundary. Due to this rounding up, old data remains in the
page cache when blocksize is less than page size and start offset is
not aligned with page size. In case of collapse range, we need to
align start offset to page size boundary by doing a round down
operation instead of round up.
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Unfortunately this contains no easter eggs, its a bit larger than I'd
like, but I included a patch that just moves code from one file to
another and I'd like to avoid merge conflicts with that later, so it
makes it seem worse than it is,
Otherwise:
- radeon: fixes to use new microcode to stabilise some cards, use
some common displayport code, some runtime pm fixes, pll regression
fixes
- i915: fix for some context oopses, a warn in a used path, backlight
fixes
- nouveau: regression fix
- omap: a bunch of fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (51 commits)
drm: bochs: drop unused struct fields
drm: bochs: add power management support
drm: cirrus: add power management support
drm: Split out drm_probe_helper.c from drm_crtc_helper.c
drm/plane-helper: Don't fake-implement primary plane disabling
drm/ast: fix value check in cbr_scan2
drm/nouveau/bios: fix a bit shift error introduced by 457e77b
drm/radeon/ci: make sure mc ucode is loaded before checking the size
drm/radeon/si: make sure mc ucode is loaded before checking the size
drm/radeon: improve PLL params if we don't match exactly v2
drm/radeon: memory leak on bo reservation failure. v2
drm/radeon: fix VCE fence command
drm/radeon: re-enable mclk dpm on R7 260X asics
drm/radeon: add support for newer mc ucode on CI (v2)
drm/radeon: add support for newer mc ucode on SI (v2)
drm/radeon: apply more strict limits for PLL params v2
drm/radeon: update CI DPM powertune settings
drm/radeon: fix runpm handling on APUs (v4)
drm/radeon: disable mclk dpm on R7 260X
drm/tegra: Remove gratuitous pad field
...
Dave Airlie [Sat, 19 Apr 2014 01:16:02 +0000 (11:16 +1000)]
Merge branch 'drm-next-3.15-wip' of git://people.freedesktop.org/~deathsimple/linux into drm-next
Some i2c fixes over DisplayPort.
* 'drm-next-3.15-wip' of git://people.freedesktop.org/~deathsimple/linux:
drm/radeon: Improve vramlimit module param documentation
drm/radeon: fix audio pin counts for DCE6+ (v2)
drm/radeon/dp: switch to the common i2c over aux code
drm/dp/i2c: Update comments about common i2c over dp assumptions (v3)
drm/dp/i2c: send bare addresses to properly reset i2c connections (v4)
drm/radeon/dp: handle zero sized i2c over aux transactions (v2)
drm/i915: support address only i2c-over-aux transactions
drm/tegra: dp: Support address-only I2C-over-AUX transactions
1) Fix mlx4_en_netpoll implementation, it needs to schedule a NAPI
context, not synchronize it. From Chris Mason.
2) Ipv4 flow input interface should never be zero, it should be
LOOPBACK_IFINDEX instead. From Cong Wang and Julian Anastasov.
3) Properly configure MAC to PHY connection in mvneta devices, from
Thomas Petazzoni.
4) sys_recv should use SYSCALL_DEFINE. From Jan Glauber.
5) Tunnel driver ioctls do not use the correct namespace, fix from
Nicolas Dichtel.
6) Fix memory leak on seccomp filter attach, from Kees Cook.
7) Fix lockdep warning for nested vlans, from Ding Tianhong.
8) Crashes can happen in SCTP due to how the auth_enable value is
managed, fix from Vlad Yasevich.
9) Wireless fixes from John W Linville and co.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
net: sctp: cache auth_enable per endpoint
tg3: update rx_jumbo_pending ring param only when jumbo frames are enabled
vlan: Fix lockdep warning when vlan dev handle notification
seccomp: fix memory leak on filter attach
isdn: icn: buffer overflow in icn_command()
ip6_tunnel: use the right netns in ioctl handler
sit: use the right netns in ioctl handler
ip_tunnel: use the right netns in ioctl handler
net: use SYSCALL_DEFINEx for sys_recv
net: mdio-gpio: Add support for separate MDI and MDO gpio pins
net: mdio-gpio: Add support for active low gpio pins
net: mdio-gpio: Use devm_ functions where possible
ipv4, route: pass 0 instead of LOOPBACK_IFINDEX to fib_validate_source()
ipv4, fib: pass LOOPBACK_IFINDEX instead of 0 to flowi4_iif
mlx4_en: don't use napi_synchronize inside mlx4_en_netpoll
net: mvneta: properly configure the MAC <-> PHY connection in all situations
net: phy: add minimal support for QSGMII PHY
sfc:On MCDI timeout, issue an FLR (and mark MCDI to fail-fast)
mwifiex: fix hung task on command timeout
mwifiex: process event before command response
...
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"A set of 5 small cifs fixes"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cif: fix dead code
cifs: fix error handling cifs_user_readv
fs: cifs: remove unused variable.
Return correct error on query of xattr on file with empty xattrs
cifs: Wait for writebacks to complete before attempting write.
Merge tag 'char-misc-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a few driver fixes for char/misc drivers that resolve
reported issues.
All have been in linux-next successfully for a few days"
* tag 'char-misc-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Drivers: hv: vmbus: Negotiate version 3.0 when running on ws2012r2 hosts
Tools: hv: Handle the case when the target file exists correctly
vme_tsi148: Utilize to_pci_dev() macro
vme_tsi148: Fix PCI address mapping assumption
vme_tsi148: Fix typo in tsi148_slave_get()
w1: avoid recursive device_add
w1: fix netlink refcnt leak on error path
misc: Grammar s/addition/additional/
drivers: mcb: fix memory leak in chameleon_parse_cells() error path
mei: ignore client writing state during cb completion
mei: me: do not load the driver if the FW doesn't support MEI interface
GenWQE: Increase driver version number
GenWQE: Fix multithreading problems
GenWQE: Ensure rc is not returning an uninitialized value
GenWQE: Add wmb before DDCB is started
GenWQE: Enable access to VPD flash area
Merge tag 'driver-core-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some driver core fixes for 3.15-rc2. Also in here are some
documentation updates, as well as an API removal that had to wait for
after -rc1 due to the cleanups coming into you from multiple developer
trees (this one and the PPC tree.)
All have been in linux next successfully"
* tag 'driver-core-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers/base/dd.c incorrect pr_debug() parameters
Documentation: Update stable address in Chinese and Japanese translations
topology: Fix compilation warning when not in SMP
Chinese: add translation of io_ordering.txt
stable_kernel_rules: spelling/word usage
sysfs, driver-core: remove unused {sysfs|device}_schedule_callback_owner()
kernfs: protect lazy kernfs_iattrs allocation with mutex
fs: Don't return 0 from get_anon_bdev
Merge tag 'staging-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are a few staging driver fixes for issues that have been reported
for 3.15-rc2.
Also dominating the diffstat for the pull request is the removal of
the rtl8187se driver. It's no longer needed in staging as a "real"
driver for this hardware is now merged in the tree in the "correct"
location in drivers/net/
All of these patches have been tested in linux-next"
* tag 'staging-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: Fix case where ethtype was never obtained and always be checked against 0
staging: r8712u: Fix case where ethtype was never obtained and always be checked against 0
staging: r8188eu: Calling rtw_get_stainfo() with a NULL sta_addr will return NULL
staging: comedi: fix circular locking dependency in comedi_mmap()
staging: r8723au: Add missing initialization of change_inx in sort algorithm
Staging: unisys: use after free in list_for_each()
staging: unisys: use after free in error messages
staging: speakup: fix misuse of kstrtol() in handle_goto()
staging: goldfish: Call free_irq in error path
staging: delete rtl8187se wireless driver
staging: rtl8723au: Fix buffer overflow in rtw_get_wfd_ie()
staging: gs_fpgaboot: remove __TIMESTAMP__ macro
staging: vme: fix memory leak in vme_user_probe()
staging: fpgaboot: clean up Makefile
staging/usbip: fix store_attach() sscanf return value check
staging/usbip: userspace - fix usbipd SIGSEGV from refresh_exported_devices()
staging: rtl8188eu: remove spaces, correct counts to unbreak P2P ioctls
staging/rtl8821ae: Fix OOM handling in _rtl_init_deferred_work()
Merge tag 'tty-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small tty/serial driver fixes for 3.15-rc2. Also
in here are some Documentation file removals for drivers that we
removed a long time ago, no need to keep it around any longer.
All of these have been in linux-next for a bit"
* tag 'tty-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: 8250, disable "too much work" messages"
serial: amba-pl011: fix regression, causing an Oops on rmmod
tty: Fix help text of SYNCLINK_CS
tty: fix memleak in alloc_pid
ttyprintk: Allow built as a module
ttyprintk: Fix wrong tty_unregister_driver() call in the error path
serial: 8250, disable "too much work" messages
Documentation/serial: Delete obsolete driver documentation
serial: omap: Fix missing pm_runtime_resume handling by simplifying code
serial_core: Fix pm imbalance on unbind
serial: pl011: change Rx burst size to half of trigger level
serial: timberdale: Depend on X86_32
serial: st-asc: Fix SysRq char handling
Revert "serial: clps711x: Give a chance to perform useful tasks during wait loop"
serial_core: Fix conditional start_tx on ring buffer not empty
serial: efm32: use $vendor,$device scheme for compatible string
serial: omap: free the wakeup settings in remove
Merge tag 'usb-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of tiny USB fixes and new device ids for 3.15-rc2.
Nothing major, just issues some people have reported.
All of these have been in linux-next"
* tag 'usb-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
uas: fix deadlocky memory allocations
uas: fix error handling during scsi_scan()
uas: fix GFP_NOIO under spinlock
uwb: adds missing error handling
USB: cdc-acm: Remove Motorola/Telit H24 serial interfaces from ACM driver
USB: ohci-jz4740: FEAT_POWER is a port feature, not a hub feature
USB: ohci-jz4740: Fix uninitialized variable warning
USB: EHCI: tegra: set txfill_tuning
usb: ehci-platform: Return immediately from suspend if ehci_suspend fails
usb: ehci-exynos: Return immediately from suspend if ehci_suspend fails
USB: fix crash during hotplug of PCI USB controller card
USB: cdc-acm: fix double usb_autopm_put_interface() in acm_port_activate()
usb: usb-common: fix typo for usb_state_string
USB: usb_wwan: fix handling of missing bulk endpoints
USB: pl2303: add ids for Hewlett-Packard HP POS pole displays
USB: cp210x: Add 8281 (Nanotec Plug & Drive)
usb: option driver, add support for Telit UE910v2
Revert "USB: serial: add usbid for dell wwan card to sierra.c"
USB: serial: ftdi_sio: add id for Brainboxes serial cards
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
thp: close race between split and zap huge pages
mm: fix new kernel-doc warning in filemap.c
mm: fix CONFIG_DEBUG_VM_RB description
mm: use paravirt friendly ops for NUMA hinting ptes
mips: export flush_icache_range
mm/hugetlb.c: add cond_resched_lock() in return_unused_surplus_pages()
wait: explain the shadowing and type inconsistencies
Shiraz has moved
Documentation/vm/numa_memory_policy.txt: fix wrong document in numa_memory_policy.txt
powerpc/mm: fix ".__node_distance" undefined
kernel/watchdog.c:touch_softlockup_watchdog(): use raw_cpu_write()
init/Kconfig: move the trusted keyring config option to general setup
vmscan: reclaim_clean_pages_from_list() must use mod_zone_page_state()
Sasha Levin has reported two THP BUGs[1][2]. I believe both of them
have the same root cause. Let's look to them one by one.
The first bug[1] is "kernel BUG at mm/huge_memory.c:1829!". It's
BUG_ON(mapcount != page_mapcount(page)) in __split_huge_page(). From my
testing I see that page_mapcount() is higher than mapcount here.
I think it happens due to race between zap_huge_pmd() and
page_check_address_pmd(). page_check_address_pmd() misses PMD which is
under zap:
CPU0 CPU1
zap_huge_pmd()
pmdp_get_and_clear()
__split_huge_page()
anon_vma_interval_tree_foreach()
__split_huge_page_splitting()
page_check_address_pmd()
mm_find_pmd()
/*
* We check if PMD present without taking ptl: no
* serialization against zap_huge_pmd(). We miss this PMD,
* it's not accounted to 'mapcount' in __split_huge_page().
*/
pmd_present(pmd) == 0
The second bug[2] is "kernel BUG at mm/huge_memory.c:1371!".
It's VM_BUG_ON_PAGE(!PageHead(page), page) in zap_huge_pmd().
This happens in similar way:
CPU0 CPU1
zap_huge_pmd()
pmdp_get_and_clear()
page_remove_rmap(page)
atomic_add_negative(-1, &page->_mapcount)
__split_huge_page()
anon_vma_interval_tree_foreach()
__split_huge_page_splitting()
page_check_address_pmd()
mm_find_pmd()
pmd_present(pmd) == 0 /* The same comment as above */
/*
* No crash this time since we already decremented page->_mapcount in
* zap_huge_pmd().
*/
BUG_ON(mapcount != page_mapcount(page))
/*
* We split the compound page here into small pages without
* serialization against zap_huge_pmd()
*/
__split_huge_page_refcount()
VM_BUG_ON_PAGE(!PageHead(page), page); // CRASH!!!
So my understanding the problem is pmd_present() check in mm_find_pmd()
without taking page table lock.
The bug was introduced by me commit with commit 117b0791ac42. Sorry for
that. :(
Let's open code mm_find_pmd() in page_check_address_pmd() and do the
check under page table lock.
Note that __page_check_address() does the same for PTE entires
if sync != 0.
I've stress tested split and zap code paths for 36+ hours by now and
don't see crashes with the patch applied. Before it took <20 min to
trigger the first bug and few hours for second one (if we ignore
first).
This appears to be a copy/paste error. Update the description to
reflect extra rbtree debug and checks for the config option instead of
duplicating CONFIG_DEBUG_VM.
mm: use paravirt friendly ops for NUMA hinting ptes
David Vrabel identified a regression when using automatic NUMA balancing
under Xen whereby page table entries were getting corrupted due to the
use of native PTE operations. Quoting him
Xen PV guest page tables require that their entries use machine
addresses if the preset bit (_PAGE_PRESENT) is set, and (for
successful migration) non-present PTEs must use pseudo-physical
addresses. This is because on migration MFNs in present PTEs are
translated to PFNs (canonicalised) so they may be translated back
to the new MFN in the destination domain (uncanonicalised).
pte_mknonnuma(), pmd_mknonnuma(), pte_mknuma() and pmd_mknuma()
set and clear the _PAGE_PRESENT bit using pte_set_flags(),
pte_clear_flags(), etc.
In a Xen PV guest, these functions must translate MFNs to PFNs
when clearing _PAGE_PRESENT and translate PFNs to MFNs when setting
_PAGE_PRESENT.
His suggested fix converted p[te|md]_[set|clear]_flags to using
paravirt-friendly ops but this is overkill. He suggested an alternative
of using p[te|md]_modify in the NUMA page table operations but this is
does more work than necessary and would require looking up a VMA for
protections.
This patch modifies the NUMA page table operations to use paravirt
friendly operations to set/clear the flags of interest. Unfortunately
this will take a performance hit when updating the PTEs on
CONFIG_PARAVIRT but I do not see a way around it that does not break
Xen.
Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: David Vrabel <david.vrabel@citrix.com> Tested-by: David Vrabel <david.vrabel@citrix.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Anvin <hpa@zytor.com> Cc: Fengguang Wu <fengguang.wu@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Steven Noonan <steven@uplinklabs.net> Cc: Rik van Riel <riel@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Cc: Cyrill Gorcunov <gorcunov@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lkdtm module performs tests against executable memory ranges, so it
needs to flush the icache for proper behaviors. Other architectures
already export this, so do the same for MIPS.
[akpm@linux-foundation.org: relocate export sites] Signed-off-by: Kees Cook <keescook@chromium.org> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Sanjay Lal <sanjayl@kymasys.com> Cc: John Crispin <blogic@openwrt.org> Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm/hugetlb.c: add cond_resched_lock() in return_unused_surplus_pages()
soft lockup in freeing gigantic hugepage fixed in commit 55f67141a892 "mm:
hugetlb: fix softlockup when a large number of hugepages are freed." can
happen in return_unused_surplus_pages(), so let's fix it.
Documentation/vm/numa_memory_policy.txt: fix wrong document in numa_memory_policy.txt
In document numa_memory_policy.txt, the following examples for flag
MPOL_F_RELATIVE_NODES are incorrect.
For example, consider a task that is attached to a cpuset with
mems 2-5 that sets an Interleave policy over the same set with
MPOL_F_RELATIVE_NODES. If the cpuset's mems change to 3-7, the
interleave now occurs over nodes 3,5-6. If the cpuset's mems
then change to 0,2-3,5, then the interleave occurs over nodes
0,3,5.
According to the comment of the patch adding flag MPOL_F_RELATIVE_NODES,
the nodemasks the user specifies should be considered relative to the
current task's mems_allowed.
(https://lkml.org/lkml/2008/2/29/428)
And according to numa_memory_policy.txt, if the user's nodemask includes
nodes that are outside the range of the new set of allowed nodes, then
the remap wraps around to the beginning of the nodemask and, if not
already set, sets the node in the mempolicy nodemask.
So in the example, if the user specifies 2-5, for a task whose
mems_allowed is 3-7, the nodemasks should be remapped the third, fourth,
fifth, sixth node in mems_allowed. like the following:
mems_allowed: 3 4 5 6 7
relative index: 0 1 2 3 4
5
So the nodemasks should be remapped to 3,5-7, but not 3,5-6.
And for a task whose mems_allowed is 0,2-3,5, the nodemasks should be
remapped to 0,2-3,5, but not 0,3,5.
mems_allowed: 0 2 3 5
relative index: 0 1 2 3
4 5
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com> Cc: Randy Dunlap <rdunlap@infradead.org> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Fri, 18 Apr 2014 22:07:12 +0000 (15:07 -0700)]
kernel/watchdog.c:touch_softlockup_watchdog(): use raw_cpu_write()
Fix:
BUG: using __this_cpu_write() in preemptible [00000000] code: systemd-udevd/497
caller is __this_cpu_preempt_check+0x13/0x20
CPU: 3 PID: 497 Comm: systemd-udevd Tainted: G W 3.15.0-rc1 #9
Hardware name: Hewlett-Packard HP EliteBook 8470p/179B, BIOS 68ICF Ver. F.02 04/27/2012
Call Trace:
check_preemption_disabled+0xe1/0xf0
__this_cpu_preempt_check+0x13/0x20
touch_nmi_watchdog+0x28/0x40
Reported-by: Luis Henriques <luis.henriques@canonical.com> Tested-by: Luis Henriques <luis.henriques@canonical.com> Cc: Eric Piel <eric.piel@tremplin-utc.net> Cc: Robert Moore <robert.moore@intel.com> Cc: Lv Zheng <lv.zheng@intel.com> Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com> Cc: Len Brown <lenb@kernel.org> Cc: Christoph Lameter <cl@linux.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Foley [Fri, 18 Apr 2014 22:07:11 +0000 (15:07 -0700)]
init/Kconfig: move the trusted keyring config option to general setup
The SYSTEM_TRUSTED_KEYRING config option is not in any menu, causing it
to show up in the toplevel of the kernel configuration. Fix this by
moving it under the General Setup menu.
Signed-off-by: Peter Foley <pefoley2@pefoley.com> Cc: David Howells <dhowells@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
What happens while auth_enable=0 in that case is, that
ep->auth_hmacs is initialized to NULL in sctp_auth_init_hmacs()
when endpoint is being created.
After that point, if an admin switches over to auth_enable=1,
the machine can crash due to NULL pointer dereference during
reception of an INIT chunk. When we enter sctp_process_init()
via sctp_sf_do_5_1B_init() in order to respond to an INIT chunk,
the INIT verification succeeds and while we walk and process
all INIT params via sctp_process_param() we find that
net->sctp.auth_enable is set, therefore do not fall through,
but invoke sctp_auth_asoc_set_default_hmac() instead, and thus,
dereference what we have set to NULL during endpoint
initialization phase.
The fix is to make auth_enable immutable by caching its value
during endpoint initialization, so that its original value is
being carried along until destruction. The bug seems to originate
from the very first days.
Fix in joint work with Daniel Borkmann.
Reported-by: Joshua Kinard <kumba@gentoo.org> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Tested-by: Joshua Kinard <kumba@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Please pull this batch of fixes intended for the 3.15 stream...
For the mac80211 bits, Johannes says:
"We have a fix from Chun-Yeow to not look at management frame bitrates
that are typically really low, two fixes from Felix for AP_VLAN
interfaces, a fix from Ido to disable SMPS settings when a monitor
interface is enabled, a radar detection fix from Michał and a fix from
myself for a very old remain-on-channel bug."
For the iwlwifi bits, Emmanuel says:
"I have new device IDs and a new firmware API. These are the trivial
ones. The less trivial ones are Johannes's fix that delays the
enablement of an interrupt coalescing hardware until after association
- this fixes a few connection problems seen in the field. Eyal has a
bunch of rate control fixes. I decided to add these for 3.15 because
they fix some disconnection and packet loss scenarios which were
reported by the field. I also have a fix for a memory leak that
happens only with a very new NIC."
Along with those...
Amitkumar Karwar fixes a couple of problems relating to driver/firmware
interactions in mwifiex.
Christian Engelmayer avoids a couple of potential memory leaks in
the new rsi driver.
Eliad Peller provides a wl18xx mailbox alignment fix for problems
when using new firmware.
Frederic Danis adds a couple of missing debugging strings to the
cw1200 driver.
Geert Uytterhoeven adds a variable initialization inside of the
rsi driver.
Luciano Coelho patches the wlcore code to ignore dummy packet events
in PLT mode in order to work around a firmware bug.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Thu, 17 Apr 2014 12:51:08 +0000 (14:51 +0200)]
tg3: update rx_jumbo_pending ring param only when jumbo frames are enabled
The patch fixes a problem with dropped jumbo frames after usage of
'ethtool -G ... rx'.
Scenario:
1. ip link set eth0 up
2. ethtool -G eth0 rx N # <- This zeroes rx-jumbo
3. ip link set mtu 9000 dev eth0
The ethtool command set rx_jumbo_pending to zero so any received jumbo
packets are dropped and you need to use 'ethtool -G eth0 rx-jumbo N'
to workaround the issue.
The patch changes the logic so rx_jumbo_pending value is changed only if
jumbo frames are enabled (MTU > 1500).
Signed-off-by: Ivan Vecera <ivecera@redhat.com> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The reason is that all of the addr_lock_key for vlan dev have the same class,
so if we change the status for vlan dev, the vlan dev and its real dev will
hold the same class of addr_lock_key together, so the warning happened.
we should distinguish the lock depth for vlan dev and its real dev.
v1->v2: Convert the vlan_netdev_addr_lock_key to an array of eight elements, which
could support to add 8 vlan id on a same vlan dev, I think it is enough for current
scene, because a netdev's name is limited to IFNAMSIZ which could not hold 8 vlan id,
and the vlan dev would not meet the same class key with its real dev.
The new function vlan_dev_get_lockdep_subkey() will return the subkey and make the vlan
dev could get a suitable class key.
v2->v3: According David's suggestion, I use the subclass to distinguish the lock key for vlan dev
and its real dev, but it make no sense, because the difference for subclass in the
lock_class_key doesn't mean that the difference class for lock_key, so I use lock_depth
to distinguish the different depth for every vlan dev, the same depth of the vlan dev
could have the same lock_class_key, I import the MAX_LOCK_DEPTH from the include/linux/sched.h,
I think it is enough here, the lockdep should never exceed that value.
v3->v4: Add a huge array of locking keys will waste static kernel memory and is not a appropriate method,
we could use _nested() variants to fix the problem, calculate the depth for every vlan dev,
and use the depth as the subclass for addr_lock_key.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
- mostly cxgb4 fixes unblocked by the merge of some prerequisites via
the net tree
- drop deprecated MSI-X API use.
- a couple other miscellaneous things.
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cxgb4: Fix over-dereference when terminating
RDMA/cxgb4: Use uninitialized_var()
RDMA/cxgb4: Add missing debug stats
RDMA/cxgb4: Initialize reserved fields in a FW work request
RDMA/cxgb4: Use pr_warn_ratelimited
RDMA/cxgb4: Max fastreg depth depends on DSGL support
RDMA/cxgb4: SQ flush fix
RDMA/cxgb4: rmb() after reading valid gen bit
RDMA/cxgb4: Endpoint timeout fixes
RDMA/cxgb4: Use the BAR2/WC path for kernel QPs and T5 devices
IB/mlx5: Add block multicast loopback support
IB/mthca: Use pci_enable_msix_exact() instead of pci_enable_msix()
IB/qib: Use pci_enable_msix_range() instead of pci_enable_msix()
Commit 93ea02bb8435 ("arch: Clean up asm/barrier.h implementations")
wired generic barrier.h for ARC, but failed to delete the existing file.
In 3.15, due to rcupdate.h updates, this causes a build breakage on ARC:
CC arch/arc/kernel/asm-offsets.s
In file included from include/linux/sched.h:45:0,
from arch/arc/kernel/asm-offsets.c:9:
include/linux/rculist.h: In function __list_add_rcu:
include/linux/rculist.h:54:2: error: implicit declaration of function smp_store_release [-Werror=implicit-function-declaration]
rcu_assign_pointer(list_next_rcu(prev), new);
^
Merge tag 'pci-v3.15-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"These are fixes for a powerpc NULL pointer dereference, an OF
interrupt mapping issue on some of the new host bridges, and a
DesignWare iATU issue.
* tag 'pci-v3.15-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: tegra: Use new OF interrupt mapping when possible
PCI: rcar: Use new OF interrupt mapping when possible
PCI: designware: Use new OF interrupt mapping when possible
PCI: designware: Fix iATU programming for cfg1, io and mem viewport
PCI: designware: Fix comment for setting number of lanes
powerpc/PCI: Fix NULL dereference in sys_pciconfig_iobase() list traversal
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fix for merge window mismerge in hid-sony, from Frank Praznik
- fix for Surface Type/Touch Cover 2 device, from Benjamin Tissoires
- quirk for ThinkPad Helix sensor hub from Stephen Chandler Paul
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: core: do not scan constant input report
Revert "HID: microsoft: Add ID's for Surface Type/Touch Cover 2"
HID: sensor-hub: add sensor hub quirk for ThinkPad Helix
HID: sony: Fix cancel_work_sync mismerge
Merge tag 'sound-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a copule of HD-audio device/codec-specific quirks, and a trivial
replacement of udelay() with mdelay() in the old es18xx driver code.
All should be safe to apply"
* tag 'sound-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Add headset Mic support for Dell machine
ALSA: hda - add headset mic detect quirk for a Dell laptop
ALSA: es18xx driver should use udelay error
ALSA: hda/realtek - Add support of ALC288 codec
Merge tag 'dt-fixes-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- fix error handling in of_update_property
- fix section mismatch warnings in __reserved_mem_check_root
- add empty of_find_node_by_path for !OF builds
- add various missing binding documentation
* tag 'dt-fixes-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: add empty of_find_node_by_path() for !OF
of: Clean up of_update_property
DT: add vendor prefix for EBV Elektronik
of: Fix the section mismatch warnings.
of: Add vendor prefix for Digi International Inc.
DT: I2C: Add trivial bindings used by kirkwood boards
DT: Vendor: Add prefixes used by Kirkwood devices
DT: bindings: add missing Marvell Kirkwood SoC documentation
dt-bindings: add vendor-prefix for Newhaven Display
of: add vendor prefix for I2SE GmbH
of: add vendor prefix for ISEE 2007 S.L.
Merge tag 'xfs-for-linus-3.15-rc2' of git://oss.sgi.com/xfs/xfs
Pull xfs bug fixes from Dave Chinner:
"The fixes are for data corruption issues, memory corruption and
regressions for changes merged in -rc1.
Data corruption fixes:
- fix a bunch of delayed allocation state mismatches
- fix collapse/zero range bugs
- fix a direct IO block mapping bug @ EOF
Other fixes:
- fix a use after free on metadata IO error
- fix a use after free on IO error during unmount
- fix an incorrect error sign on direct IO write errors
- add missing O_TMPFILE inode security context initialisation"
* tag 'xfs-for-linus-3.15-rc2' of git://oss.sgi.com/xfs/xfs:
xfs: fix tmpfile/selinux deadlock and initialize security
xfs: fix buffer use after free on IO error
xfs: wrong error sign conversion during failed DIO writes
xfs: unmount does not wait for shutdown during unmount
xfs: collapse range is delalloc challenged
xfs: don't map ranges that span EOF for direct IO
xfs: zeroing space needs to punch delalloc blocks
xfs: xfs_vm_write_end truncates too much on failure
xfs: write failure beyond EOF truncates too much data
xfs: kill buffers over failed write ranges properly
Merge tag 'trace-fixes-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"This contains two fixes.
The first is to remove a duplication of creating debugfs files that
already exist and causes an error report to be printed due to the
failure of the second creation.
The second is a memory leak fix that was introduced in 3.14"
* tag 'trace-fixes-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/uprobes: Fix uprobe_cpu_buffer memory leak
tracing: Do not try to recreated toplevel set_ftrace_* files
ext4: fix extent merging in ext4_ext_shift_path_extents()
There is a bug in ext4_ext_shift_path_extents() where if we actually
manage to merge a extent we would skip shifting the next extent. This
will result in in one extent in the extent tree not being properly
shifted.
This is causing failure in various xfstests tests using fsx or fsstress
with collapse range support. It will also cause file system corruption
which looks something like:
e2fsck 1.42.9 (4-Feb-2014)
Pass 1: Checking inodes, blocks, and sizes
Inode 20 has out of order extents
(invalid logical block 3, physical block 492938, len 2)
Clear? yes
...
when running e2fsck.
It's also very easily reproducible just by running fsx without any
parameters. I can usually hit the problem within a minute.
Fix it by increasing ex_start only if we're not merging the extent.
Currently in ext4_collapse_range() and ext4_punch_hole() we're
discarding preallocation twice. Once before we attempt to do any changes
and second time after we're done with the changes.
While the second call to ext4_discard_preallocations() in
ext4_punch_hole() case is not needed, we need to discard preallocation
right after ext4_ext_remove_space() in collapse range case because in
the case we had to restart a transaction in the middle of removing space
we might have new preallocations created.
Remove unneeded ext4_discard_preallocations() ext4_punch_hole() and move
it to the better place in ext4_collapse_range()
ext4: no need to truncate pagecache twice in collapse range
We're already calling truncate_pagecache() before we attempt to do any
actual job so there is not need to truncate pagecache once more using
truncate_setsize() after we're finished.
Remove truncate_setsize() and replace it just with i_size_write() note
that we're holding appropriate locks.
ext4: fix removing status extents in ext4_collapse_range()
Currently in ext4_collapse_range() when calling ext4_es_remove_extent() to
remove status extents we're passing (EXT_MAX_BLOCKS - punch_start - 1)
in order to remove all extents from start of the collapse range to the
end of the file. However this is wrong because we might miss the
possible extent covering the last block of the file.
ext4: use filemap_write_and_wait_range() correctly in collapse range
Currently we're passing -1 as lend argumnet for
filemap_write_and_wait_range() which is wrong since lend is signed type
so it would cause some confusion and we might not write_and_wait for the
entire range we're expecting to write.
We should be using truncate_pagecache() instead of
truncate_pagecache_range() in the collapse range because we're
truncating page cache from offset to the end of file.
truncate_pagecache() also get rid of the private COWed pages from the
range because we're going to shift the end of the file.
Alexander Shiyan [Wed, 16 Apr 2014 06:49:20 +0000 (10:49 +0400)]
of: add empty of_find_node_by_path() for !OF
Add an empty version of of_find_node_by_path().
This fixes following build error for asoc tree:
sound/soc/fsl/fsl_ssi.c: In function 'fsl_ssi_probe':
sound/soc/fsl/fsl_ssi.c:1471:2: error: implicit declaration of function 'of_find_node_by_path' [-Werror=implicit-function-declaration]
sprop = of_get_property(of_find_node_by_path("/"), "compatible", NULL);
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Rob Herring <robh@kernel.org>
perf/x86/intel: Use rdmsrl_safe() when initializing RAPL PMU
CPUs which should support the RAPL counters according to
Family/Model/Stepping may still issue #GP when attempting to access
the RAPL MSRs. This may happen when Linux is running under KVM and
we are passing-through host F/M/S data, for example. Use rdmsrl_safe
to first access the RAPL_POWER_UNIT MSR; if this fails, do not
attempt to use this PMU.
Signed-off-by: Venkatesh Srinivas <venkateshs@google.com> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1394739386-22260-1-git-send-email-venkateshs@google.com Cc: zheng.z.yan@intel.com Cc: eranian@google.com Cc: ak@linux.intel.com Cc: linux-kernel@vger.kernel.org
[ The patch also silently fixes another bug: rapl_pmu_init() didn't handle the memory alloc failure case previously. ] Signed-off-by: Ingo Molnar <mingo@kernel.org>
Kirill Tkhai [Fri, 14 Mar 2014 22:15:07 +0000 (02:15 +0400)]
sched: Revert commit 4c6c4e38c4e9 ("sched/core: Fix endless loop in pick_next_task()")
This reverts commit 4c6c4e38c4e9 ("sched/core: Fix endless loop in
pick_next_task()"), which is not necessary after ("sched/rt: Substract number
of tasks of throttled queues from rq->nr_running").
Signed-off-by: Kirill Tkhai <tkhai@yandex.ru> Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
[conflict resolution with stop task checking patch] Signed-off-by: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1394835307.18748.34.camel@HP-250-G1-Notebook-PC Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Kirill Tkhai [Fri, 14 Mar 2014 22:15:00 +0000 (02:15 +0400)]
sched/rt: Substract number of tasks of throttled queues from rq->nr_running
Now rq->rt becomes to be able to be in dequeued or enqueued state.
We add new member rt_rq->rt_queued, which is used to indicate this.
The member is used only for top queue rq->rt_rq.
The goal is to fit generic scheme which is used in deadline and
fair classes, i.e. throttled rt_rq's rt_nr_running is beeing
substracted from rq->nr_running.
Kirill Tkhai [Fri, 14 Mar 2014 22:14:49 +0000 (02:14 +0400)]
sched/rt: Sum number of all children tasks in hierarhy at ->rt_nr_running
{inc,dec}_rt_tasks() used to count entities which are directly queued
on the rt_rq. If an entity was not a task (i.e., it is some queue), its
children were not counted.
There is no problem here, but now we want to count number of all tasks
which are actually queued under the rt_rq in all the hierarchy (except
throttled rt queues).
Empty queues are not able to be queued and all of the places, which
use ->rt_nr_running, just compare it with zero, so we do not break
anything here.
Signed-off-by: Kirill Tkhai <tkhai@yandex.ru> Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1394835289.18748.31.camel@HP-250-G1-Notebook-PC Cc: linux-kernel@vger.kernel.org
[ Twiddled the changelog. ] Signed-off-by: Ingo Molnar <mingo@kernel.org>
Kirill V Tkhai [Wed, 12 Mar 2014 10:18:33 +0000 (06:18 -0400)]
sched/rt: Do not try to push tasks if pinned task switches to RT
Just switched pinned task is not able to be pushed. If the rq had had
several RT tasks before they have already been considered as candidates
to be pushed (or pulled).
Signed-off-by: Kirill V Tkhai <tkhai@yandex.ru> Acked-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20140312061833.3a43aa64@gandalf.local.home Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Daniel Vetter [Thu, 10 Apr 2014 08:51:11 +0000 (10:51 +0200)]
drm: Split out drm_probe_helper.c from drm_crtc_helper.c
This is leftover stuff from my previous doc round which I kinda wanted
to do but didn't yet due to rebase hell.
The modeset helpers and the probing helpers a independent and e.g.
i915 uses the probing stuff but has its own modeset infrastructure. It
hence makes to split this up. While at it add a DOC: comment for the
probing libraray.
It would be rather neat to pull some of the DocBook documenting these
two helpers into in-line DOC: comments. But unfortunately kerneldoc
doesn't support markdown or something similar to make nice-looking
documentation, so the current state is better.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
After thinking about this topic a bit more I've reached the conclusion
that implementing this doesn't make sense:
- The locking is all wrong: set_config(NULL) will also unlink encoders
and connectors, but those links are protected with the mode_config
mutex. In the ->disable_plane callback we only hold all modeset
locks, but eventually we want to switch to just grabbing the
per-crtc (and maybe per-plane) locks as needed, maybe based on
ww_mutexes. Having a callback which absolutely needs all modeset
locks is bad for this conversion.
Note that the same isn't true for the provided ->update_plane since
we've audited the crtc helpers to make sure that not encoder or
connector links are changed.
- There's no way to re-enable the plane with an ->update_plane: The
connectors/encoder links are lost and so we can't re-enable the
CRTC. Even without that issue the driver might have reassigned some
shared resources (as opposed to e.g. DPMS off, where drivers are not
allowed to do that to make sure the CRTC can be enabled again).
- The semantics don't make much sense: Userspace asked to scan out
black (or some other color if the driver supports a background
color), not that the screen be disabled.
- Implementing proper primary plane support (i.e. actually disabling
the primary plane without disabling the CRTC) is really simple, at
least if all the hw needs is flipping a bit. The big task is
auditing all the interactions with other ioctls when the CRTC is on
but there's no primary plane (e.g. pageflips). And some of that work
still needs to be done.
Cc: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
projects / mirror_ubuntu-bionic-kernel.git / log