Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu arch update from Greg Ungerer:
"Quite a varied set of changes this time.
- A little more merge cleanup, this time the assembler entry code.
- New sub-architecture support for the ColdFire 5251/5253 and 5441x
CPU families.
- Specific clk support code for the ColdFire 520x and 532x CPU
familes.
- Refactoring of the ColdFire GPIO support.
- PCI bus support for some ColdFire CPUS that have PCI hardware (54xx
family). This showed up a few problems with ColdFire cache,
allocating coherent memory and bi-directional DMA support. Fixes
for those too."
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (21 commits)
m68k: allow PCI bus to be enabled for ColdFire m54xx CPUs
m68k: add PCI bus code support for the ColdFire M54xx SoC family
m68k: add IO access definitions to support PCI on ColdFire platforms
m68k: add PCI bus support definitions for the ColdFire M54xx SoC family
m68k: common PCI support definitions and code
m68k: add support for DMA_BIDIRECTIONAL in dma support functions
m68k: fix ColdFire clear cache operation
m68k: use simpler dma_alloc_coherent() for ColdFire CPUs
m68knommu: platform support for 8390 based ethernet used on some boards
m68knommu: Add clk definitions for m532x.
m68knommu: Add clk definitions for m520x.
m68knommu: Add rtc device for m5441x.
m68knommu: add definitions for the third interrupt controller on devices that don't have a third interrupt controller.
m68knommu: Add support for the Coldfire m5441x.
m68knommu: use MCF_IRQ_PIT1 instead of MCFINT_VECBASE + MCFINT_PIT1
coldfire-qspi: Add support for the Coldfire 5251/5253.
m68knommu: Add support for the Coldfire 5251/5253
m68knommu: refactor Coldfire GPIO not to require GPIOLIB, eliminate mcf_gpio_chips.
m68k: merge the MMU and non-MMU versions of the entry.S code
m68k: use jbsr to call functions instead of bsrl
...
Merge branch 'next' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine update from Vinod Koul:
"This time we have a new dmaengine driver from the tegra folks. Also
we have Guennadi's cleanup of sh drivers which incudes a library for
sh drivers. And the usual odd fixes in bunch of drivers and some nice
cleanup of dw_dmac from Andy."
Fix up conflicts in drivers/mmc/host/sh_mmcif.c
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (46 commits)
dmaengine: Cleanup logging messages
mmc: sh_mmcif: switch to the new DMA channel allocation and configuration
dma: sh: provide a migration path for slave drivers to stop using .private
dma: sh: use an integer slave ID to improve API compatibility
dmaengine: shdma: prepare to stop using struct dma_chan::private
sh: remove unused DMA device pointer from SIU platform data
ASoC: siu: don't use DMA device for channel filtering
dmaengine: shdma: (cosmetic) simplify a static function
dmaengine: at_hdmac: add a few const qualifiers
dw_dmac: use 'u32' for LLI structure members, not dma_addr_t
dw_dmac: mark dwc_dump_lli inline
dma: mxs-dma: Export missing symbols from mxs-dma.c
dma: shdma: convert to the shdma base library
ASoC: fsi: prepare for conversion to the shdma base library
usb: renesas_usbhs: prepare for conversion to the shdma base library
ASoC: siu: prepare for conversion to the shdma base library
serial: sh-sci: prepare for conversion to the shdma base library
mmc: sh_mobile_sdhi: prepare for conversion to the shdma base library
mmc: sh_mmcif: remove unneeded struct sh_mmcif_dma, prepare to shdma conversion
dma: shdma: prepare for conversion to the shdma base library
...
Merge tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull common clk framework changes from Michael Turquette:
"This includes a small number of core framework improvments, platform
ports and new DT bindings."
Fix up trivial conflicts in drivers/clk/Makefile
* tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux: (21 commits)
clk: fix compile for OF && !COMMON_CLK
clk: fix clk_get on of_clk_get_by_name return check
clk: mxs: clk_register_clkdev mx28 usb clocks
clk: add highbank clock support
dt: add clock binding doc to primecell bindings
clk: add DT fixed-clock binding support
clk: add DT clock binding support
ARM: integrator: convert to common clock
clk: add versatile ICST307 driver
ARM: integrator: put symbolic bus names on devices
ARM: u300: convert to common clock
clk: cache parent clocks only for muxes
clk: wm831x: Add initial WM831x clock driver
clk: Constify struct clk_init_data
clk: Add CLK_IS_BASIC flag to identify basic clocks
clk: Add support for rate table based dividers
clk: Add support for power of two type dividers
clk: mxs: imx28: decrease the frequency of ref_io1 for SSP2 and SSP3
clk: mxs: add clkdev lookup for pwm
clk: mxs: Fix the GPMI clock name
...
Merge tag 'iommu-updates-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"The most important part of these updates is the IOMMU groups code
enhancement written by Alex Williamson. It abstracts the problem that
a given hardware IOMMU can't isolate any given device from any other
device (e.g. 32 bit PCI devices can't usually be isolated). Devices
that can't be isolated are grouped together. This code is required
for the upcoming VFIO framework.
Another IOMMU-API change written by me is the introduction of domain
attributes. This makes it easier to handle GART-like IOMMUs with the
IOMMU-API because now the start-address and the size of the domain
address space can be queried.
Besides that there are a few cleanups and fixes for the NVidia Tegra
IOMMU drivers and the reworked init-code for the AMD IOMMU. The
latter is from my patch-set to support interrupt remapping. The rest
of this patch-set requires x86 changes which are not mergabe yet. So
full support for interrupt remapping with AMD IOMMUs will come in a
future merge window."
* tag 'iommu-updates-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (33 commits)
iommu/amd: Fix hotplug with iommu=pt
iommu/amd: Add missing spin_lock initialization
iommu/amd: Convert iommu initialization to state machine
iommu/amd: Introduce amd_iommu_init_dma routine
iommu/amd: Move unmap_flush message to amd_iommu_init_dma_ops()
iommu/amd: Split enable_iommus() routine
iommu/amd: Introduce early_amd_iommu_init routine
iommu/amd: Move informational prinks out of iommu_enable
iommu/amd: Split out PCI related parts of IOMMU initialization
iommu/amd: Use acpi_get_table instead of acpi_table_parse
iommu/amd: Fix sparse warnings
iommu/tegra: Don't call alloc_pdir with as->lock
iommu/tegra: smmu: Fix unsleepable memory allocation at alloc_pdir()
iommu/tegra: smmu: Remove unnecessary sanity check at alloc_pdir()
iommu/exynos: Implement DOMAIN_ATTR_GEOMETRY attribute
iommu/tegra: Implement DOMAIN_ATTR_GEOMETRY attribute
iommu/msm: Implement DOMAIN_ATTR_GEOMETRY attribute
iommu/omap: Implement DOMAIN_ATTR_GEOMETRY attribute
iommu/vt-d: Implement DOMAIN_ATTR_GEOMETRY attribute
iommu/amd: Implement DOMAIN_ATTR_GEOMETRY attribute
...
Merge tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug:
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug:
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos
Kong)
Dynamic resource management:
- Track bus number allocation (struct resource tree per domain)
(Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment
(Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management:
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization:
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex
Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous:
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup()
(Myron Stowe)"
* tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (122 commits)
PCI: hotplug: ensure a consistent return value in error case
PCI: fix undefined reference to 'pci_fixup_final_inited'
PCI: build resource code for M68K architecture
PCI: pciehp: remove unused pciehp_get_max_lnk_width(), pciehp_get_cur_lnk_width()
PCI: reorder __pci_assign_resource() (no change)
PCI: fix truncation of resource size to 32 bits
PCI: acpiphp: merge acpiphp_debug and debug
PCI: acpiphp: remove unused res_lock
sparc/PCI: replace pci_cfg_fake_ranges() with pci_read_bridge_bases()
PCI: call final fixups hot-added devices
PCI: move final fixups from __init to __devinit
x86/PCI: move final fixups from __init to __devinit
MIPS/PCI: move final fixups from __init to __devinit
PCI: support sizing P2P bridge I/O windows with 1K granularity
PCI: reimplement P2P bridge 1K I/O windows (Intel P64H2)
PCI: disable MEM decoding while updating 64-bit MEM BARs
PCI: leave MEM and IO decoding disabled during 64-bit BAR sizing, too
PCI: never discard enable/suspend/resume_early/resume fixups
PCI: release temporary reference in __nv_msi_ht_cap_quirk()
PCI: restructure 'pci_do_fixups()'
...
Merge tag 'dt-for-3.6' of git://sources.calxeda.com/kernel/linux
Pull devicetree updates from Rob Herring:
"A small set of changes for devicetree:
- Couple of Documentation fixes
- Addition of new helper function of_node_full_name
- Improve of_parse_phandle_with_args return values
- Some NULL related sparse fixes"
Grant's busy packing.
* tag 'dt-for-3.6' of git://sources.calxeda.com/kernel/linux:
of: mtd: nuke useless const qualifier
devicetree: add helper inline for retrieving a node's full name
of: return -ENOENT when no property
usage-model.txt: fix typo machine_init->init_machine
of: Fix null pointer related warnings in base.c file
LED: Fix missing semicolon in OF documentation
of: fix a few typos in the binding documentation
Merge tag 'pinctrl-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
"These are the accumulated pin control patches for v3.6:
- Various cleanups to the U300 driver
- Refactor the pin control core to automatically remove any GPIO
ranges when the drivers are removed, instead of having the drivers
do this explicitly.
- Add a function for registering a batch of GPIO ranges.
- Fix a number of incorrect but non-regressive error checks.
- Incremental improvements to the COH901, i.MX and Nomadik drivers
- Add a one-register-per-pin entirely Device Tree-based pin control
driver from Tony Lindgren."
* tag 'pinctrl-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: Add one-register-per-pin type device tree based pinctrl driver
pinctrl/nomadik: add spi2_oc1_2 pin group
pinctrl/nomadik: kerneldoc fix
pinctrl/nomadik: use devm_* allocators for gpio probe
pinctrl/nomadik: add pin group to mco function
pinctrl/nomadik: add hsit_a_2 pin group
pinctrl/nomadik: add pin group smcs1 and smps0
pinctrl/nomadik: fix hsir_a_1_pins pin list
pinctrl: pinctrl-imx: fix map setting problem if NO_PAD_CTL is set
pinctrl/coh901: use clk_prepare_[en|dis]able()
pinctrl/pinctrl-tegra: remove IS_ERR checking of pmx->pctl
pinctrl/pinctrl-spear: remove IS_ERR checking of pmx->pctl
pinctrl/u300: drop unused variable
pinctrl: select the proper symbol
pinctrl: add pinctrl_add_gpio_ranges function
pinctrl: remove pinctrl_remove_gpio_range
pinctrl/pinctrl-core: cleanup pinctrl_register
pinctrl/u300: delete pointless debug print
pinctrl/pinctrl-u300: remove devm_kfree at driver unload
Merge tag 'rdma-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- Updates to the qib low-level driver
- First chunk of changes for SR-IOV support for mlx4 IB
- RDMA CM support for IPv6-only binding
- Other misc cleanups and fixes
Fix up some add-add conflicts in include/linux/mlx4/device.h and
drivers/net/ethernet/mellanox/mlx4/main.c
* tag 'rdma-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (30 commits)
IB/qib: checkpatch fixes
IB/qib: Add congestion control agent implementation
IB/qib: Reduce sdma_lock contention
IB/qib: Fix an incorrect log message
IB/qib: Fix QP RCU sparse warnings
mlx4: Put physical GID and P_Key table sizes in mlx4_phys_caps struct and paravirtualize them
mlx4_core: Allow guests to have IB ports
mlx4_core: Implement mechanism for reserved Q_Keys
net/mlx4_core: Free ICM table in case of error
IB/cm: Destroy idr as part of the module init error flow
mlx4_core: Remove double function declarations
IB/mlx4: Fill the masked_atomic_cap attribute in query device
IB/mthca: Fill in sq_sig_type in query QP
IB/mthca: Warning about event for non-existent QPs should show event type
IB/qib: Fix sparse RCU warnings in qib_keys.c
net/mlx4_core: Initialize IB port capabilities for all slaves
mlx4: Use port management change event instead of smp_snoop
IB/qib: RCU locking for MR validation
IB/qib: Avoid returning EBUSY from MR deregister
IB/qib: Fix UC MR refs for immediate operations
...
Merge branch 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull i2c updates from Jean Delvare:
"The most important changes here are a big cleanup of the i2c-piix4
driver, cleanups and interrupt support to the i2c-i801 driver, and
support for the SCCB protocol."
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-omap: Add support for I2C_M_STOP message flag
i2c: Fall back to emulated SMBus if the operation isn't supported natively
i2c: Add SCCB support
i2c-tiny-usb: Add support for the Robofuzz OSIF USB/I2C converter
i2c-i801: Enable IRQ for byte_by_byte transactions
i2c-i801: Enable interrupts on ICH5/7/8/9/10
i2c-i801: Enable IRQ for SMBus transactions
i2c-i801: Consolidate polling
i2c-i801: Drop ENABLE_INT9
i2c-i801: Rename some SMBHSTCNT bit constants
i2c-i801: Check and return errors during byte-by-byte transfers
i2c-i801: Clear only status bits in HST_STS
i2c-i801: Refactor use of LAST_BYTE in i801_block_transaction_byte_by_byte
i2c-smbus: Use module_i2c_driver()
i2c/writing-clients: Mention module_i2c_driver()
i2c-piix4: Support AMD auxiliary SMBus controller
i2c-piix4: Separate registration and probing code
i2c-piix4: Eliminate piix4_smba global variable
i2c/busses: Use module_pci_driver
i2c: Update Guenter Roeck's e-mail address
Merge tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound update from Takashi Iwai:
"This is a fairly quiet release in all sound area. Only a little bit
of changes in the core side while most of changes are seen in the
drivers.
HD-audio:
- A few new codec additions for Nvidia, Realtek and VIA
- Intel Haswell audio support
- Support for "phantom" jacks for consistent jack reporting
- Major clean-ups in HDMI/DP driver codes
- A workaround for inverted digital-mic pins with Realtek codecs
- Removal of beep_mode=2 option
ASoC:
- Added the ability to add and remove DAPM paths dynamically, mostly
for reparenting on clock changes
- New machine drivers for Marvell Brownstone, ST-Ericsson Ux500
reference platform and ttc-dkp
- New CPU drivers for Blackfin BF6xx SPORTs in I2S mode, Marvell MMP,
Synopsis Designware I2S controllers, and SPEAr DMA and S/PDIF
- New CODEC drivers for Dialog DA732x, ST STA529, ST-Ericsson AB8500,
TI Isabelle and Wolfson Microelectronics WM5102 and WM5110
- DAPM fixes for the recent locking changes
- Fix for _PRE and _POST widgets (which have been broken for a few
releases now)
- A couple of minor driver updates
Misc
- Conversion to new dev_pm_ops in platform and PCI drivers
- LTC support and some fixes in PCXHR driver
- A few fixes and PM support for ISA OPti9xx and WSS cards
- Some TLV code cleanup
- Move driver-specific headers from include/sound to local dirs"
* tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (212 commits)
ASoC: dapm: Fix _PRE and _POST events for DAPM performance improvements
ALSA: hda - add dock support for Thinkpad X230 Tablet
ALSA: hda - Turn on PIN_OUT from hdmi playback prepare.
ASoC imx-audmux: add MX31_AUDMUX_PORT7_SSI_PINS_7 define
ASoC: littlemill: Add userspace control of the WM1250 I/O
ASoC: wm8994: Update micdet for irqdomain conversion
ALSA: hda - make sure alc268 does not OOPS on codec parse
ALSA: hda - Add support for Realtek ALC282
ALSA: hda - Fix index number conflicts of phantom jacks
ALSA: opti9xx: Fix section mismatch by PM support
ALSA: snd-opti9xx: Implement suspend/resume
ALSA: hda - Add new GPU codec ID to snd-hda
ALSA: hda - Fix driver type of Haswell controller to AZX_DRIVER_SCH
ALSA: hda - add Haswell HDMI codec id
ALSA: hda - Add DeviceID for Haswell HDA
ALSA: wss_lib: Fix resume on Yamaha OPL3-SAx
ALSA: wss_lib: fix suspend/resume
ALSA: es1938: replace TLV_DB_RANGE_HEAD with DECLARE_TLV_DB_RANGE
ALSA: tlv: add DECLARE_TLV_DB_RANGE()
ALSA: tlv: add DECLARE_TLV_CONTAINER()
...
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree from Jiri Kosina:
"Trivial updates all over the place as usual."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (29 commits)
Fix typo in include/linux/clk.h .
pci: hotplug: Fix typo in pci
iommu: Fix typo in iommu
video: Fix typo in drivers/video
Documentation: Add newline at end-of-file to files lacking one
arm,unicore32: Remove obsolete "select MISC_DEVICES"
module.c: spelling s/postition/position/g
cpufreq: Fix typo in cpufreq driver
trivial: typo in comment in mksysmap
mach-omap2: Fix typo in debug message and comment
scsi: aha152x: Fix sparse warning and make printing pointer address more portable.
Change email address for Steve Glendinning
Btrfs: fix typo in convert_extent_bit
via: Remove bogus if check
netprio_cgroup.c: fix comment typo
backlight: fix memory leak on obscure error path
Documentation: asus-laptop.txt references an obsolete Kconfig item
Documentation: ManagementStyle: fixed typo
mm/vmscan: cleanup comment error in balance_pgdat
mm: cleanup on the comments of zone_reclaim_stat
...
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
"The list of changes worth pointing out explicitly:
- We are getting 'UHID', which is a new framework for implementing HID
transport drivers in userspace (this is different from HIDRAW, which
is transport-independent and provides report parsing facilities;
uhid is for the other (transport) part of the pipeline).
It's needed for (and currently being used by) Bluetooth-LowEnergy,
as its specification mandates things we don't want in the kernel.
Written by David Herrmann.
- there have been quite a few bugs in runtime suspend/resume paths
(probably never reported to actually happen in the wild, but still).
Alan Stern fixed those.
- a few other driver updates and fixes and random new device support."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (45 commits)
HID: add ASUS AIO keyboard model AK1D
HID: add support for Cypress barcode scanner 04B4:ED81
HID: Allow drivers to be their own listener
HID: usbhid: fix error paths in suspend
HID: usbhid: check for suspend or reset before restarting
HID: usbhid: replace HID_REPORTED_IDLE with HID_SUSPENDED
HID: usbhid: inline some simple routines
HID: usbhid: fix autosuspend calls
HID: usbhid: fix use-after-free bug
HID: hid-core: optimize in case of hidraw
HID: hidraw: fix list->buffer memleak
HID: uhid: Fix sending events with invalid data
HID: roccat: added sensor sysfs attribute for Savu
HID: Add driver for Holtek based keyboards with broken HID
HID: Add suport for the brightness control keys on HP keyboards
HID: magicmouse: Implement Multi-touch Protocol B (MT-B)
HID: magicmouse: Removing report_touches switch
HID: roccat: rename roccat_common functions to roccat_common2
HID: roccat: fix wrong hid_err usage on struct usb_device
HID: roccat: move functionality to roccat-common
...
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers for DA9052/53 PMIC as well as HIH-6130/HIH-6131 humidity
and temperature sensors.
Convert drivers to use devm_ functions and to use dev_pm_ops. Address
a couple of Coverity errors/warnings as well as compile warnings.
Some functional improvements in applesmc driver."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (72 commits)
hwmon: (applesmc) Ignore some temperature registers
hwmon: (applesmc) Allow negative temperature values
hwmon: (s3c-hwmon) Use devm_kzalloc instead of kzalloc
hwmon: (w83781d) Fix compile warning
hwmon: (applesmc) Shorten minimum wait time
hwmon: (exynos4_tmu) Use struct dev_pm_ops for power management
hwmon: (gpio-fan) Use struct dev_pm_ops for power management
hwmon: (abituguru3) Use struct dev_pm_ops for power management
hwmon: (abituguru) Use struct dev_pm_ops for power management
hwmon: (acpi_power_meter) Fix unintentional integer overflow
hwmon: (acpi_power_meter) Cleanup and optimizations
hwmon: Honeywell Humidicon HIH-6130/HIH-6131 humidity and temperature sensor driver
hwmon: (applesmc) Skip sensor mapping
hwmon: (ntc_thermistor) Ensure that data->name string is terminated
hwmon: (w83l785ts) Convert to use devm_ functions
hwmon: (w83l785ts) Simplify code and improve readability
hwmon: (smsc47m192) Convert to use devm_ functions
hwmon: (smsc47m1) Convert to use devm_ functions
hwmon: (smsc47b397) Convert to use devm_ functions
hwmon: (k8temp) Convert to use devm_ functions
...
Pull watchdog changes from Wim Van Sebroeck:
- conversion of iTCO_wdt and orion_wdt to the generic watchdog API
- uses module_platform_driver() for s3c2410_wdt
- Adds support for Jetway JNF99 Motherboard
- various fixes
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: orion_wdt: Convert driver to watchdog core
watchdog: s3c2410_wdt: Use module_platform_driver()
watchdog: sch311x_wdt: Fix Polarity when starting watchdog
Watchdog: OMAP: Fix the runtime pm code to avoid module getting stuck intransition state.
watchdog: ie6xx_wdt: section mismatch in ie6xx_wdt_probe()
watchdog: bcm63xx_wdt: fix driver section mismatch
watchdog: iTCO_wdt.c: convert to watchdog core
char/ipmi: remove local ioctl defines replaced by generic ones
watchdog: xilinx: Read clock frequency directly from DT node
watchdog: coh901327_wdt: use clk_prepare/unprepare
watchdog: f71808e_wdt: Add support for Jetway JNF99 motherboard
Merge tag 'stable/for-linus-3.6-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/mm
Pull frontswap updates from Konrad Rzeszutek Wilk:
"Cleanups in code and documentation. Little bit of refactoring for
cleaner look."
* tag 'stable/for-linus-3.6-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/mm:
mm/frontswap: cleanup doc and comment error
mm: frontswap: remove unneeded headers
mm: frontswap: split out function to clear a page out
mm: frontswap: remove unnecessary check during initialization
mm: frontswap: make all branches of if statement in put page consistent
mm: frontswap: split frontswap_shrink further to simplify locking
mm: frontswap: split out __frontswap_unuse_pages
mm: frontswap: split out __frontswap_curr_pages
mm: frontswap: trivial coding convention issues
mm: frontswap: remove casting from function calls through ops structure
Merge tag 'stable/for-linus-3.6-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen update from Konrad Rzeszutek Wilk:
"Features:
* Performance improvement to lower the amount of traps the hypervisor
has to do 32-bit guests. Mainly for setting PTE entries and
updating TLS descriptors.
* MCE polling driver to collect hypervisor MCE buffer and present
them to /dev/mcelog.
* Physical CPU online/offline support. When an privileged guest is
booted it is present with virtual CPUs, which might have an 1:1 to
physical CPUs but usually don't. This provides mechanism to
offline/online physical CPUs.
Bug-fixes for:
* Coverity found fixes in the console and ACPI processor driver.
* PVonHVM kexec fixes along with some cleanups.
* Pages that fall within E820 gaps and non-RAM regions (and had been
released to hypervisor) would be populated back, but potentially in
non-RAM regions."
* tag 'stable/for-linus-3.6-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: populate correct number of pages when across mem boundary (v2)
xen PVonHVM: move shared_info to MMIO before kexec
xen: simplify init_hvm_pv_info
xen: remove cast from HYPERVISOR_shared_info assignment
xen: enable platform-pci only in a Xen guest
xen/pv-on-hvm kexec: shutdown watches from old kernel
xen/x86: avoid updating TLS descriptors if they haven't changed
xen/x86: add desc_equal() to compare GDT descriptors
xen/mm: zero PTEs for non-present MFNs in the initial page table
xen/mm: do direct hypercall in xen_set_pte() if batching is unavailable
xen/hvc: Fix up checks when the info is allocated.
xen/acpi: Fix potential memory leak.
xen/mce: add .poll method for mcelog device driver
xen/mce: schedule a workqueue to avoid sleep in atomic context
xen/pcpu: Xen physical cpus online/offline sys interface
xen/mce: Register native mce handler as vMCE bounce back point
x86, MCE, AMD: Adjust initcall sequence for xen
xen/mce: Add mcelog support for Xen platform
Merge tag 'kvm-3.6-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Avi Kivity:
"Highlights include
- full big real mode emulation on pre-Westmere Intel hosts (can be
disabled with emulate_invalid_guest_state=0)
- relatively small ppc and s390 updates
- PCID/INVPCID support in guests
- EOI avoidance; 3.6 guests should perform better on 3.6 hosts on
interrupt intensive workloads)
- Lockless write faults during live migration
- EPT accessed/dirty bits support for new Intel processors"
Fix up conflicts in:
- Documentation/virtual/kvm/api.txt:
Stupid subchapter numbering, added next to each other.
Duplicated commits through the kvm tree and the s390 tree, with
subsequent edits in the KVM tree.
* tag 'kvm-3.6-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (93 commits)
KVM: fix race with level interrupts
x86, hyper: fix build with !CONFIG_KVM_GUEST
Revert "apic: fix kvm build on UP without IOAPIC"
KVM guest: switch to apic_set_eoi_write, apic_write
apic: add apic_set_eoi_write for PV use
KVM: VMX: Implement PCID/INVPCID for guests with EPT
KVM: Add x86_hyper_kvm to complete detect_hypervisor_platform check
KVM: PPC: Critical interrupt emulation support
KVM: PPC: e500mc: Fix tlbilx emulation for 64-bit guests
KVM: PPC64: booke: Set interrupt computation mode for 64-bit host
KVM: PPC: bookehv: Add ESR flag to Data Storage Interrupt
KVM: PPC: bookehv64: Add support for std/ld emulation.
booke: Added crit/mc exception handler for e500v2
booke/bookehv: Add host crit-watchdog exception support
KVM: MMU: document mmu-lock and fast page fault
KVM: MMU: fix kvm_mmu_pagetable_walk tracepoint
KVM: MMU: trace fast page fault
KVM: MMU: fast path of handling guest page fault
KVM: MMU: introduce SPTE_MMU_WRITEABLE bit
KVM: MMU: fold tlb flush judgement into mmu_spte_update
...
1) Remove the ipv4 routing cache. Now lookups go directly into the FIB
trie and use prebuilt routes cached there.
No more garbage collection, no more rDOS attacks on the routing
cache. Instead we now get predictable and consistent performance,
no matter what the pattern of traffic we service.
This has been almost 2 years in the making. Special thanks to
Julian Anastasov, Eric Dumazet, Steffen Klassert, and others who
have helped along the way.
I'm sure that with a change of this magnitude there will be some
kind of fallout, but such things ought the be simple to fix at this
point. Luckily I'm not European so I'll be around all of August to
fix things :-)
The major stages of this work here are each fronted by a forced
merge commit whose commit message contains a top-level description
of the motivations and implementation issues.
2) Pre-demux of established ipv4 TCP sockets, saves a route demux on
input.
3) TCP SYN/ACK performance tweaks from Eric Dumazet.
4) Add namespace support for netfilter L4 conntrack helpers, from Gao
Feng.
5) Add config mechanism for Energy Efficient Ethernet to ethtool, from
Yuval Mintz.
6) Remove quadratic behavior from /proc/net/unix, from Eric Dumazet.
7) Support for connection tracker helpers in userspace, from Pablo
Neira Ayuso.
8) Allow userspace driven TX load balancing functions in TEAM driver,
from Jiri Pirko.
9) Kill off NLMSG_PUT and RTA_PUT macros, more gross stuff with
embedded gotos.
10) TCP Small Queues, essentially minimize the amount of TCP data queued
up in the packet scheduler layer. Whereas the existing BQL (Byte
Queue Limits) limits the pkt_sched --> netdevice queuing levels,
this controls the TCP --> pkt_sched queueing levels.
From Eric Dumazet.
11) Reduce the number of get_page/put_page ops done on SKB fragments,
from Alexander Duyck.
12) Implement protection against blind resets in TCP (RFC 5961), from
Eric Dumazet.
13) Support the client side of TCP Fast Open, basically the ability to
send data in the SYN exchange, from Yuchung Cheng.
Basically, the sender queues up data with a sendmsg() call using
MSG_FASTOPEN, then they do the connect() which emits the queued up
fastopen data.
14) Avoid all the problems we get into in TCP when timers or PMTU events
hit a locked socket. The TCP Small Queues changes added a
tcp_release_cb() that allows us to queue work up to the
release_sock() caller, and that's what we use here too. From Eric
Dumazet.
15) Zero copy on TX support for TUN driver, from Michael S. Tsirkin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1870 commits)
genetlink: define lockdep_genl_is_held() when CONFIG_LOCKDEP
r8169: revert "add byte queue limit support".
ipv4: Change rt->rt_iif encoding.
net: Make skb->skb_iif always track skb->dev
ipv4: Prepare for change of rt->rt_iif encoding.
ipv4: Remove all RTCF_DIRECTSRC handliing.
ipv4: Really ignore ICMP address requests/replies.
decnet: Don't set RTCF_DIRECTSRC.
net/ipv4/ip_vti.c: Fix __rcu warnings detected by sparse.
ipv4: Remove redundant assignment
rds: set correct msg_namelen
openvswitch: potential NULL deref in sample()
tcp: dont drop MTU reduction indications
bnx2x: Add new 57840 device IDs
tcp: avoid oops in tcp_metrics and reset tcpm_stamp
niu: Change niu_rbr_fill() to use unlikely() to check niu_rbr_add_page() return value
niu: Fix to check for dma mapping errors.
net: Fix references to out-of-scope variables in put_cmsg_compat()
net: ethernet: davinci_emac: add pm_runtime support
net: ethernet: davinci_emac: Remove unnecessary #include
...
Merge tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming
Pull C6X changes from Mark Salter:
- remove use of legacy irqs which really wasn't needed
- add support for C66x SoC on EVMC6678 board
- clean up compiler warning
* tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming:
C6X: clean up compiler warning
C6X: add basic support for TMS320C6678 SoC
C6X: remove dependence on legacy IRQs
C6X: remove megamod-pic requirement on direct-mapped core pic
i2c: Fall back to emulated SMBus if the operation isn't supported natively
Adapter drivers might support only a subset of the SMBus operations
natively. Those drivers currently have to manually emulate unsupported
operations using I2C.
Make the i2c_smbus_xfer() function fall back to
i2c_smbus_xfer_emulated() when the adapter's .smbus_xfer() operation
returns -EOPNOTSUPP, like it already does when the .smbus_xfer()
operation isn't available at all.
[JD: Minor optimization.]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
SCCB is a serial communication bus developed by Omnivision. Its 2-wire
mode is very similar to SMBus byte data transactions, but requires the
controller to ignore the ACK bit and to insert a stop condition after
each message.
Add a device SCCB flag and a message stop flag to be passed to
controller drivers.
[JD: Kill rogue definition in go7007 driver.]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
i2c-tiny-usb: Add support for the Robofuzz OSIF USB/I2C converter
Robofuzz OSIF is a generic USB/iIC interface that embeds an ATMega8A
AVR-RISC microcontroler.
The device is based upon Till Harbaum's i2c-tiny-usb and although it
enhances the original design with further functionnalities it still
maintain compatibility with it with respect to the USB/I2C interface.
Signed-off-by: Emmanuel Deloget <logout@free.fr> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Daniel Kurtz [Tue, 24 Jul 2012 12:13:59 +0000 (14:13 +0200)]
i2c-i801: Enable IRQ for byte_by_byte transactions
Byte-by-byte transactions are used primarily for accessing I2C devices
with an SMBus controller. For these transactions, for each byte that is
read or written, the SMBus controller generates a BYTE_DONE IRQ. The isr
reads/writes the next byte, and clears the IRQ flag to start the next byte.
On the penultimate IRQ, the isr also sets the LAST_BYTE flag.
There is no locking around the cmd/len/count/data variables, since the
I2C adapter lock ensures there is never multiple simultaneous transactions
for the same device, and the driver thread never accesses these variables
while interrupts might be occurring.
The end result is faster I2C block read and write transactions.
Note: This patch has only been tested and verified by doing I2C read and
write block transfers on Cougar Point 6 Series PCH, as well as I2C read
block transfers on ICH5.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Tue, 24 Jul 2012 12:13:59 +0000 (14:13 +0200)]
i2c-i801: Enable interrupts on ICH5/7/8/9/10
Enable interrupts on more devices. ICH5, ICH7(-M) and ICH10 have been
tested to work OK. ICH8 and ICH9 are expected to work just fine as
they are very close to ICH7 and ICH10.
Ultimately we want to enable this feature on at least every device
since the ICH5, but for now we limit the exposure. We'll enable it for
other devices if we don't get negative feedback.
As a bonus, let the user know when interrupts are used.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Daniel Kurtz <djkurtz@chromium.org>
Daniel Kurtz [Tue, 24 Jul 2012 12:13:58 +0000 (14:13 +0200)]
i2c-i801: Enable IRQ for SMBus transactions
Add a new 'feature' to i2c-i801 to enable using PCI interrupts.
When the feature is enabled, then an isr is installed for the device's
PCI IRQ.
An I2C/SMBus transaction is always terminated by one of the following
interrupt sources: FAILED, BUS_ERR, DEV_ERR, or on success: INTR.
When the isr fires for one of these cases, it sets the ->status variable
and wakes up the waitq. The waitq then saves off the status code, and
clears ->status (in preparation for some future transaction).
The SMBus controller generates an INTR irq at the end of each
transaction where INTREN was set in the HST_CNT register.
No locking is needed around accesses to priv->status since all writes to
it are serialized: it is only ever set once in the isr at the end of a
transaction, and cleared while no interrupts can occur. In addition, the
I2C adapter lock guarantees that entire I2C transactions for a single
adapter are always serialized.
For this patch, the INTREN bit is set only for SMBus block, byte and word
transactions, but not for I2C reads or writes. The use of the DS
(BYTE_DONE) interrupt with byte-by-byte I2C transactions is implemented in
a subsequent patch.
The interrupt feature has only been enabled for COUGARPOINT hardware.
In addition, it is disabled if SMBus is using the SMI# interrupt.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Tue, 24 Jul 2012 12:13:58 +0000 (14:13 +0200)]
i2c-i801: Consolidate polling
(Based on earlier work by Daniel Kurtz.)
Come up with a consistent, driver-wide strategy for event polling. For
intermediate steps of byte-by-byte block transactions, check for
BYTE_DONE or any error flag being set. At the end of every transaction
(regardless of PEC being used), check for both BUSY being cleared and
INTR or any error flag being set. This ensures proper action for all
transaction types.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Daniel Kurtz <djkurtz@chromium.org>
Daniel Kurtz [Tue, 24 Jul 2012 12:13:58 +0000 (14:13 +0200)]
i2c-i801: Check and return errors during byte-by-byte transfers
If an error is detected in the polling loop, abort the transaction and
return an error code.
* DEV_ERR is set if the device does not respond with an acknowledge, and
the SMBus controller times out (minimum 25ms).
* BUS_ERR is set if a bus arbitration collision is detected. In other
words, when the SMBus controller tries to generate a START condition, but
detects that the SMBDATA is being held low, usually by another SMBus/I2C
master.
* FAILED is only set if a transaction is stopped by software (using
the SMBHSTCNT KILL bit).
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Daniel Kurtz [Tue, 24 Jul 2012 12:13:57 +0000 (14:13 +0200)]
i2c-i801: Clear only status bits in HST_STS
Writing back the whole status register could clear unwanted bits.
In particular, it could clear the "INUSE_STS" bit, which is a
'hardware semaphore', that might be useful to use some day.
To prepare for this, let's ban writing back the whole status to register
HST_STS, of which this is the only instance.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Daniel Kurtz [Tue, 24 Jul 2012 12:13:57 +0000 (14:13 +0200)]
i2c-i801: Refactor use of LAST_BYTE in i801_block_transaction_byte_by_byte
As a slight optimization, pull some logic out of the polling loop during
byte-by-byte transactions by just setting the I801_LAST_BYTE bit, as
defined in the i801 (PCH) datasheet, when reading the last byte of a
byte-by-byte I2C_SMBUS_READ.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Andrew Armenia [Tue, 24 Jul 2012 12:13:57 +0000 (14:13 +0200)]
i2c-piix4: Support AMD auxiliary SMBus controller
Some AMD chipsets, such as the SP5100, have an auxiliary SMBus
controller with a second set of registers. This patch adds
support for this auxiliary controller.
Tested on ASUS KCMA-D8 motherboard.
Signed-off-by: Andrew Armenia <andrew@asquaredlabs.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Andrew Armenia [Tue, 24 Jul 2012 12:13:56 +0000 (14:13 +0200)]
i2c-piix4: Separate registration and probing code
Some chipsets have multiple sets of SMBus registers each controlling a
separate SMBus. Supporting these chipsets properly will require registering
multiple I2C adapters for one piix4.
The code to initialize and register the i2c_adapter structure has been
separated from piix4_probe and allows registration of a piix4 adapter
given its base address. Note that the i2c_adapter and i2c_piix4_adapdata
structures are now dynamically allocated.
Signed-off-by: Andrew Armenia <andrew@asquaredlabs.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Andrew Armenia [Tue, 24 Jul 2012 12:13:56 +0000 (14:13 +0200)]
i2c-piix4: Eliminate piix4_smba global variable
Some chipsets have multiple sets of piix4-compatible SMBus registers.
Eliminating the global variable will allow these chipsets to be fully
supported.
Return value from piix4_setup and piix4_sb800_setup now returns the smba
value detected. This is stored in a struct i2c_piix4_adapdata. Thus
the global variable is eliminated.
Signed-off-by: Andrew Armenia <andrew@asquaredlabs.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Axel Lin [Tue, 24 Jul 2012 12:13:56 +0000 (14:13 +0200)]
i2c/busses: Use module_pci_driver
Convert the drivers in drivers/i2c/busses/* to usemodule_pci_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Rudolf Marek <r.marek@assembler.cz> Cc: Olof Johansson <olof@lixom.net> Cc: "Mark M. Hoffman" <mhoffman@lightlink.com> Cc: Tomoya MORINAGA <tomoya.rohm@gmail.com>
WANG Cong [Tue, 24 Jul 2012 05:44:01 +0000 (13:44 +0800)]
genetlink: define lockdep_genl_is_held() when CONFIG_LOCKDEP
lockdep_is_held() is defined when CONFIG_LOCKDEP, not CONFIG_PROVE_LOCKING.
Cc: "David S. Miller" <davem@davemloft.net> Cc: Jesse Gross <jesse@nicira.com> Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bob Liu [Wed, 11 Jul 2012 07:28:11 +0000 (15:28 +0800)]
blackfin: cplb-nompu: fix ROM cplb size for bf609-ezkit
In user xip test, there is a cplb error when ROMKERNEL try to mount romfs
using 'mount -t romfs /dev/mtdblock2 /mnt', becasue the CPLB setting is not
correct.
Sonic Zhang [Thu, 28 Jun 2012 11:16:48 +0000 (19:16 +0800)]
bf60x: sec: Clean up interrupt initialization code for SEC.
Turn SEC related macro CONFIG_BF60x into SEC_GCTL.
Move machine specific GPIO_PINT macros to machine gpio header.
Split SEC init_arch_irq() and vec_to_irq() from old SIC.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Bob Liu <lliubbo@gmail.com>
Sonic Zhang [Mon, 23 Jul 2012 03:35:30 +0000 (11:35 +0800)]
bfin: pm: add deepsleep for bf60x
Add add deepsleep for bf60x.
1. Call DMC init functions to enter and exit DDR self refresh mode.
2. Wait till CGU PLL is locked after wake up and exit DDR self refresh mode.
3. Make asessembly function enter_deepsleep comply with C funtion ABI in
order to call other C functions.
4. Switch kernel stack by register EX_SCRATCH_REG.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Bob Liu <lliubbo@gmail.com>
Pull arch/tile updates from Chris Metcalf:
"These changes provide support for PCIe root complex and USB host mode
for tilegx's on-chip I/Os.
In addition, this pull provides the required underpinning for the
on-chip networking support that was pulled into 3.5. The changes have
all been through LKML (with several rounds for PCIe RC) and on
linux-next."
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: updates to pci root complex from community feedback
bounce: allow use of bounce pool via config option
usb: add host support for the tilegx architecture
arch/tile: provide kernel support for the tilegx USB shim
tile pci: enable IOMMU to support DMA for legacy devices
arch/tile: enable ZONE_DMA for tilegx
tilegx pci: support I/O to arbitrarily-cached pages
tile: remove unused header
arch/tile: tilegx PCI root complex support
arch/tile: provide kernel support for the tilegx TRIO shim
arch/tile: break out the "csum a long" function to <asm/checksum.h>
arch/tile: provide kernel support for the tilegx mPIPE shim
arch/tile: common DMA code for the GXIO IORPC subsystem
arch/tile: support MMIO-based readb/writeb etc.
arch/tile: introduce GXIO IORPC framework for tilegx
Merge tag 'please-pull-misc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull misc Itanium fixes from Tony Luck.
* tag 'please-pull-misc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
debug: Do not permit CONFIG_DEBUG_STACK_USAGE=y on IA64 or PARISC
[IA64] Port OOM changes to ia64_do_page_fault
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH updates from Paul Mundt:
- Migration off of old-style dynamic IRQ API.
- irqdomain and generic irq chip propagation.
- div4/6 clock consolidation, another step towards co-existing with the
common struct clk infrastructure.
- Extensive PFC rework
- Decoupling GPIO from pin state.
- Initial pinctrl support to facilitate incremental migration off of
legacy pinmux.
- gpiolib support made optional, and made pinctrl-backed.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (38 commits)
sh: pfc: pin config get/set support.
sh: pfc: Prefer DRV_NAME over KBUILD_MODNAME.
sh: pfc: pinctrl legacy group support.
sh: pfc: Ignore pinmux GPIOs with invalid enum IDs.
sh: pfc: Export pinctrl binding init symbol.
sh: pfc: Error out on pinctrl init resolution failure.
sh: pfc: Make pr_fmt consistent across pfc drivers.
sh: pfc: pinctrl legacy function support.
sh: pfc: Rudimentary pinctrl-backed GPIO support.
sh: pfc: Dumb GPIO stringification.
sh: pfc: Shuffle PFC support core.
sh: pfc: Verify pin type encoding size at build time.
sh: pfc: Kill off unused pinmux bias flags.
sh: pfc: Make gpio chip support optional where possible.
sh: pfc: Split out gpio chip support.
sh64: Fix up section mismatch warnings.
sh64: Attempt to make reserved insn trap handler resemble C.
sh: Consolidate die definitions for trap handlers.
sh64: Kill off old exception debugging helpers.
sh64: Use generic unaligned access control/counters.
...
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc updates from Benjamin Herrenschmidt:
"Notable highlights:
- iommu improvements from Anton removing the per-iommu global lock in
favor of dividing the DMA space into pools, each with its own lock,
and hashed on the CPU number. Along with making the locking more
fine grained, this gives significant improvements in multiqueue
networking scalability.
- Still from Anton, we know provide a vdso based variant of getcpu
which makes sched_getcpu with the appropriate glibc patch something
like 18 times faster.
- More anton goodness (he's been busy !) in other areas such as a
faster __clear_user and copy_page on P7, various perf fixes to
improve sampling quality, etc...
- One more step toward removing legacy i2c interfaces by using new
device-tree based probing of platform devices for the AOA audio
drivers
- A nice series of patches from Michael Neuling that helps avoiding
confusion between register numbers and litterals in assembly code,
trying to enforce the use of "%rN" register names in gas rather
than plain numbers.
- A pile of FSL updates
- The usual bunch of small fixes, cleanups etc...
You may spot a change to drivers/char/mem. The patch got no comment
or ack from outside, it's a trivial patch to allow the architecture to
skip creating /dev/port, which we use to disable it on ppc64 that
don't have a legacy brige. On those, IO ports 0...64K are not mapped
in kernel space at all, so accesses to /dev/port cause oopses (and
yes, distros -still- ship userspace that bangs hard coded ports such
as kbdrate)."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
powerpc/mpic: Create a revmap with enough entries for IPIs and timers
Remove stale .rej file
powerpc/iommu: Fix iommu pool initialization
powerpc/eeh: Check handle_eeh_events() return value
powerpc/85xx: Add phy nodes in SGMII mode for MPC8536/44/72DS & P2020DS
powerpc/e500: add paravirt QEMU platform
powerpc/mpc85xx_ds: convert to unified PCI init
powerpc/fsl-pci: get PCI init out of board files
powerpc/85xx: Update corenet64_smp_defconfig
powerpc/85xx: Update corenet32_smp_defconfig
powerpc/85xx: Rename P1021RDB-PC device trees to be consistent
powerpc/watchdog: move booke watchdog param related code to setup-common.c
sound/aoa: Adapt to new i2c probing scheme
i2c/powermac: Improve detection of devices from device-tree
powerpc: Disable /dev/port interface on systems without an ISA bridge
of: Improve prom_update_property() function
powerpc: Add "memory" attribute for mfmsr()
powerpc/ftrace: Fix assembly trampoline register usage
powerpc/hw_breakpoints: Fix incorrect pointer access
powerpc: Put the gpr save/restore functions in their own section
...
projects / mirror_ubuntu-eoan-kernel.git / log