gpiolib has a corner case with open drain outputs that are emulated.
When such outputs are outputting a logic 1, emulation will set the
hardware to input mode, which will cause gpiod_get_direction() to
report that it is in input mode. This is different from the behaviour
with a true open-drain output.
Unify the semantics here.
Cc: <stable@vger.kernel.org> Suggested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
ata_qc_complete_multiple() is called with a mask of the still active
tags.
mv_sata doesn't have this information directly and instead calculates
the still active tags from the started tags (ap->qc_active) and the
finished tags as (ap->qc_active ^ done_mask)
Since 28361c40368 the hw_tag and tag are no longer the same and the
equation is no longer valid. In ata_exec_internal_sg() ap->qc_active is
initialized as 1ULL << ATA_TAG_INTERNAL, but in hardware tag 0 is
started and this will be in done_mask on completion. ap->qc_active ^
done_mask becomes 0x100000000 ^ 0x1 = 0x100000001 and thus tag 0 used as
the internal tag will never be reported as completed.
This is fixed by introducing ata_qc_get_active() which returns the
active hardware tags and calling it where appropriate.
This is tested on mv_sata, but sata_fsl and sata_nv suffer from the same
problem. There is another case in sata_nv that most likely needs fixing
as well, but this looks a little different, so I wasn't confident enough
to change that.
Fixes: 28361c403683 ("libata: add extra internal command") Cc: stable@vger.kernel.org Tested-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing export of ata_qc_get_active(), as per Pali.
Set AHCI_HFLAG_DELAY_ENGINE for the BCM7425 AHCI controller thus making
it conforming to the 'strict' AHCI implementation which this controller
is based on.
This solves long link establishment with specific hard drives (e.g.:
Seagate ST1000VM002-9ZL1 SC12) that would otherwise have to complete the
error recovery handling before finally establishing a succesful SATA
link at the desired speed.
We re-order the hpriv->flags assignment to also remove the NONCQ quirk
since we can set the flag directly.
Fixes: 9586114cf1e9 ("ata: ahci_brcmstb: add support MIPS-based platforms") Fixes: 423be77daabe ("ata: ahci_brcmstb: add quirk for broken ncq") Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The downstream implementation of ahci_brcm.c did contain clock
management recovery, but until recently, did that outside of the
libahci_platform helpers and this was unintentionally stripped out while
forward porting the patch upstream.
Add the missing clock management during recovery and sleep for 10
milliseconds per the design team recommendations to ensure the SATA PHY
controller and AFE have been fully quiesced.
Fixes: eb73390ae241 ("ata: ahci_brcm: Recover from failures to identify devices") Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The AHCI resources management within ahci_brcm.c is a little
convoluted, largely because it historically had a dedicated clock that
was managed within this file in the downstream tree. Once brough
upstream though, the clock was left to be managed by libahci_platform.c
which is entirely appropriate.
This patch series ensures that the AHCI resources are fetched and
enabled before any register access is done, thus avoiding bus errors on
platforms which clock gate the controller by default.
As a result we need to re-arrange the suspend() and resume() functions
in order to avoid accessing registers after the clocks have been turned
off respectively before the clocks have been turned on. Finally, we can
refactor brcm_ahci_get_portmask() in order to fetch the number of ports
from hpriv->mmio which is now accessible without jumping through hoops
like we used to do.
The commit pointed in the Fixes tag is both old and new enough not to
require major headaches for backporting of this patch.
Fixes: eba68f829794 ("ata: ahci_brcmstb: rename to support across Broadcom SoC's") Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This reverts commit 6bb86fefa086faba7b60bb452300b76a47cde1a5
("libahci_platform: Staticize ahci_platform_<en/dis>able_phys()") we are
going to need ahci_platform_{enable,disable}_phys() in a subsequent
commit for ahci_brcm.c in order to properly control the PHY
initialization order.
Also make sure the function prototypes are declared in
include/linux/ahci_platform.h as a result.
Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
dmaengine_desc_set_reuse() allocates a struct dma_slave_caps on the
stack, populates it using dma_get_slave_caps() and then accesses one
of its members.
However dma_get_slave_caps() may fail and this isn't accounted for,
leading to a legitimate warning of gcc-4.9 (but not newer versions):
In file included from drivers/spi/spi-bcm2835.c:19:0:
drivers/spi/spi-bcm2835.c: In function 'dmaengine_desc_set_reuse':
>> include/linux/dmaengine.h:1370:10: warning: 'caps.descriptor_reuse' is used uninitialized in this function [-Wuninitialized]
if (caps.descriptor_reuse) {
Fix it, thereby also silencing the gcc-4.9 warning.
The issue has been present for 4 years but surfaces only now that
the first caller of dmaengine_desc_set_reuse() has been added in
spi-bcm2835.c. Another user of reusable DMA descriptors has existed
for a while in pxa_camera.c, but it sets the DMA_CTRL_REUSE flag
directly instead of calling dmaengine_desc_set_reuse(). Nevertheless,
tag this commit for stable in case there are out-of-tree users.
The ram_core.c routines treat przs as circular buffers. When writing a
new crash dump, the old buffer needs to be cleared so that the new dump
doesn't end up in the wrong place (i.e. at the end).
The solution to this problem is to reset the circular buffer state before
writing a new Oops dump.
Signed-off-by: Aleksandr Yashkin <a.yashkin@inango-systems.com> Signed-off-by: Nikolay Merinov <n.merinov@inango-systems.com> Signed-off-by: Ariel Gilman <a.gilman@inango-systems.com> Link: https://lore.kernel.org/r/20191223133816.28155-1-n.merinov@inango-systems.com Fixes: 896fc1f0c4c6 ("pstore/ram: Switch to persistent_ram routines") Cc: stable@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This is because the status is not set if the page is already on the
target node, but move_pages() should return valid status as long as it
succeeds. The valid status may be errno or node id.
We can't simply initialize status array to zero since the pages may be
not on node 0. Fix it by updating status with node id which the page is
already on.
Link: http://lkml.kernel.org/r/1575584353-125392-1-git-send-email-yang.shi@linux.alibaba.com Fixes: a49bd4d71637 ("mm, numa: rework do_pages_move") Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com> Reported-by: Felix Abecassis <fabecassis@nvidia.com> Tested-by: Felix Abecassis <fabecassis@nvidia.com> Suggested-by: Michal Hocko <mhocko@suse.com> Reviewed-by: John Hubbard <jhubbard@nvidia.com> Acked-by: Christoph Lameter <cl@linux.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: <stable@vger.kernel.org> [4.17+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The cred_jar kmem_cache is already memcg accounted in the current kernel
but cred->security is not. Account cred->security to kmemcg.
Recently we saw high root slab usage on our production and on further
inspection, we found a buggy application leaking processes. Though that
buggy application was contained within its memcg but we observe much
more system memory overhead, couple of GiBs, during that period. This
overhead can adversely impact the isolation on the system.
One source of high overhead we found was cred->security objects, which
have a lifetime of at least the life of the process which allocated
them.
Link: http://lkml.kernel.org/r/20191205223721.40034-1-shakeelb@google.com Signed-off-by: Shakeel Butt <shakeelb@google.com> Acked-by: Chris Down <chris@chrisdown.name> Reviewed-by: Roman Gushchin <guro@fb.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When zspage is migrated to the other zone, the zone page state should be
updated as well, otherwise the NR_ZSPAGE for each zone shows wrong
counts including proc/zoneinfo in practice.
Link: http://lkml.kernel.org/r/1575434841-48009-1-git-send-email-chanho.min@lge.com Fixes: 91537fee0013 ("mm: add NR_ZSMALLOC to vmstat") Signed-off-by: Chanho Min <chanho.min@lge.com> Signed-off-by: Jinsuk Choi <jjinsuk.choi@lge.com> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Acked-by: Minchan Kim <minchan@kernel.org> Cc: <stable@vger.kernel.org> [4.9+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently wait_event_interruptible_timeout is called in cec_thread_func()
when adap->transmitting is set. But if the adapter is unconfigured
while transmitting, then adap->transmitting is set to NULL. But the
hardware is still actually transmitting the message, and that's
indicated by adap->transmit_in_progress and we should wait until that
is finished or times out before transmitting new messages.
As the original commit says: adap->transmitting is the userspace view,
adap->transmit_in_progress reflects the hardware state.
However, if adap->transmitting is NULL and adap->transmit_in_progress
is true, then wait_event_interruptible is called (no timeout), which
can get stuck indefinitely if the CEC driver is flaky and never marks
the transmit-in-progress as 'done'.
So test against transmit_in_progress when deciding whether to use
the timeout variant or not, instead of testing against adap->transmitting.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Fixes: 32804fcb612b ("media: cec: keep track of outstanding transmits") Cc: <stable@vger.kernel.org> # for v4.19 and up Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
WARN if transmit_queue_sz is 0 but do not decrement it.
The CEC adapter will become unresponsive if it goes below
0 since then it thinks there are 4 billion messages in the
queue.
Obviously this should not happen, but a driver bug could
cause this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Cc: <stable@vger.kernel.org> # for v4.12 and up Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Declaring __current_thread_info as a global register variable has the
effect of preventing GCC from saving & restoring its value in cases
where the ABI would typically do so.
To quote GCC documentation:
> If the register is a call-saved register, call ABI is affected: the
> register will not be restored in function epilogue sequences after the
> variable has been assigned. Therefore, functions cannot safely return
> to callers that assume standard ABI.
When our position independent VDSO is built for the n32 or n64 ABIs all
functions it exposes should be preserving the value of $gp/$28 for their
caller, but in the presence of the __current_thread_info global register
variable GCC stops doing so & simply clobbers $gp/$28 when calculating
the address of the GOT.
In cases where the VDSO returns success this problem will typically be
masked by the caller in libc returning & restoring $gp/$28 itself, but
that is by no means guaranteed. In cases where the VDSO returns an error
libc will typically contain a fallback path which will now fail
(typically with a bad memory access) if it attempts anything which
relies upon the value of $gp/$28 - eg. accessing anything via the GOT.
One fix for this would be to move the declaration of
__current_thread_info inside the current_thread_info() function,
demoting it from global register variable to local register variable &
avoiding inadvertently creating a non-standard calling ABI for the VDSO.
Unfortunately this causes issues for clang, which doesn't support local
register variables as pointed out by commit fe92da0f355e ("MIPS: Changed
current_thread_info() to an equivalent supported by both clang and GCC")
which introduced the global register variable before we had a VDSO to
worry about.
Instead, fix this by continuing to use the global register variable for
the kernel proper but declare __current_thread_info as a simple extern
variable when building the VDSO. It should never be referenced, and will
cause a link error if it is. This resolves the calling convention issue
for the VDSO without having any impact upon the build of the kernel
itself for either clang or gcc.
Signed-off-by: Paul Burton <paulburton@kernel.org> Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO") Reported-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com> Tested-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Christian Brauner <christian.brauner@canonical.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: <stable@vger.kernel.org> # v4.4+ Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the HDMI unbinds drm_connector_cleanup() and drm_encoder_cleanup()
are called. This also happens when the connector and the encoder are
destroyed. This double call triggers a NULL pointer exception.
The patch fixes this by removing the cleanup calls in the unbind
function.
Cc: <stable@vger.kernel.org> Fixes: 9c5681011a0c ("drm/sun4i: Add HDMI support") Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20191217124632.20820-1-stefan@olimex.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Make sure to check the return value of usb_altnum_to_altsetting() to
avoid dereferencing a NULL pointer when the requested alternate settings
is missing.
The format altsetting number may come from a quirk table and there does
not seem to be any other validation of it (the corresponding index is
checked however).
Jia-Ju Bai reported a possible sleep-in-atomic scenario in the ice1724
driver with Infrasonic Quartet support code: namely, ice->set_rate
callback gets called inside ice->reg_lock spinlock, while the callback
in quartet.c holds ice->gpio_mutex.
This patch fixes the invalid call: it simply moves the calls of
ice->set_rate and ice->set_mclk callbacks outside the spinlock.
On Big Endian architectures, u16 port value was extracted from the wrong
parts of u32 sreg_port, just like commit 10596608c4d62 ("netfilter:
nf_tables: fix mismatch in big-endian system") describes.
When assiging and testing taskstats in taskstats_exit() there's a race
when setting up and reading sig->stats when a thread-group with more
than one thread exits:
write to 0xffff8881157bbe10 of 8 bytes by task 7951 on cpu 0:
taskstats_tgid_alloc kernel/taskstats.c:567 [inline]
taskstats_exit+0x6b7/0x717 kernel/taskstats.c:596
do_exit+0x2c2/0x18e0 kernel/exit.c:864
do_group_exit+0xb4/0x1c0 kernel/exit.c:983
get_signal+0x2a2/0x1320 kernel/signal.c:2734
do_signal+0x3b/0xc00 arch/x86/kernel/signal.c:815
exit_to_usermode_loop+0x250/0x2c0 arch/x86/entry/common.c:159
prepare_exit_to_usermode arch/x86/entry/common.c:194 [inline]
syscall_return_slowpath arch/x86/entry/common.c:274 [inline]
do_syscall_64+0x2d7/0x2f0 arch/x86/entry/common.c:299
entry_SYSCALL_64_after_hwframe+0x44/0xa9
read to 0xffff8881157bbe10 of 8 bytes by task 7949 on cpu 1:
taskstats_tgid_alloc kernel/taskstats.c:559 [inline]
taskstats_exit+0xb2/0x717 kernel/taskstats.c:596
do_exit+0x2c2/0x18e0 kernel/exit.c:864
do_group_exit+0xb4/0x1c0 kernel/exit.c:983
__do_sys_exit_group kernel/exit.c:994 [inline]
__se_sys_exit_group kernel/exit.c:992 [inline]
__x64_sys_exit_group+0x2e/0x30 kernel/exit.c:992
do_syscall_64+0xcf/0x2f0 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fix this by using smp_load_acquire() and smp_store_release().
Reported-by: syzbot+c5d03165a1bd1dead0c1@syzkaller.appspotmail.com Fixes: 34ec12349c8a ("taskstats: cleanup ->signal->stats allocation") Cc: stable@vger.kernel.org Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com> Acked-by: Marco Elver <elver@google.com> Reviewed-by: Will Deacon <will@kernel.org> Reviewed-by: Andrea Parri <parri.andrea@gmail.com> Reviewed-by: Dmitry Vyukov <dvyukov@google.com> Link: https://lore.kernel.org/r/20191009114809.8643-1-christian.brauner@ubuntu.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The auto-parser assigns the bass speaker to DAC3 (NID 0x06) which
is without the volume control. I do not see a reason to use DAC2,
because the shared output to all speakers produces the sufficient
and well balanced sound. The stereo support is enough for this
purpose (laptop).
ASUS reported that there's an bass speaker in addition to internal
speaker and it uses DAC 0x02. It was not enabled in the commit 436e25505f34 ("ALSA: hda/realtek - Enable internal speaker of ASUS
UX431FLC") which only enables the amplifier and the front speaker.
This commit enables the bass speaker on top of the aforementioned
work to improve the acoustic experience.
Fixes: 436e25505f34 ("ALSA: hda/realtek - Enable internal speaker of ASUS UX431FLC") Signed-off-by: Chris Chiu <chiu@endlessm.com> Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191230031118.95076-1-chiu@endlessm.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When CONFIG_XEN_BALLOON_MEMORY_HOTPLUG is not defined
reserve_additional_memory() will set balloon_stats.target_pages to a
wrong value in case there are still some ballooned pages allocated via
alloc_xenballooned_pages().
This will result in balloon_process() no longer be triggered when
ballooned pages are freed in batches.
Reported-by: Nicholas Tsirakis <niko.tsirakis@gmail.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Objects allocated by xen_blkif_alloc come from the 'blkif_cache' kmem
cache. This cache is destoyed when xen-blkif is unloaded so it is
necessary to wait for the deferred free routine used for such objects to
complete. This necessity was missed in commit 14855954f636 "xen-blkback:
allow module to be cleanly unloaded". This patch fixes the problem by
taking/releasing extra module references in xen_blkif_alloc/free()
respectively.
Signed-off-by: Paul Durrant <pdurrant@amazon.com> Reviewed-by: Roger Pau Monné <roger.pau@citrix.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The s390 CPU Measurement sampling facility has an overflow condition
which fires when all entries in a SBD are used.
The measurement alert interrupt is triggered and reads out all samples
in this SDB. It then tests the successor SDB, if this SBD is not full,
the interrupt handler does not read any samples at all from this SDB
The design waits for the hardware to fill this SBD and then trigger
another meassurement alert interrupt.
This scheme works nicely until
an perf_event_overflow() function call discards the sample due to
a too high sampling rate.
The interrupt handler has logic to read out a partially filled SDB
when the perf event overflow condition in linux common code is met.
This causes the CPUM sampling measurement hardware and the PMU
device driver to operate on the same SBD's trailer entry.
This should not happen.
This can be seen here using this trace:
cpumsf_pmu_add: tear:0xb5286000
hw_perf_event_update: sdbt 0xb5286000 full 1 over 0 flush_all:0
hw_perf_event_update: sdbt 0xb5286008 full 0 over 0 flush_all:0
above shows 1. interrupt
hw_perf_event_update: sdbt 0xb5286008 full 1 over 0 flush_all:0
hw_perf_event_update: sdbt 0xb5286008 full 0 over 0 flush_all:0
above shows 2. interrupt
... this goes on fine until...
hw_perf_event_update: sdbt 0xb5286068 full 1 over 0 flush_all:0
perf_push_sample1: overflow
one or more samples read from the IRQ handler are rejected by
perf_event_overflow() and the IRQ handler advances to the next SDB
and modifies the trailer entry of a partially filled SDB.
hw_perf_event_update: sdbt 0xb5286070 full 0 over 0 flush_all:1
timestamp: 14:32:52.519953
Next time the IRQ handler is called for this SDB the trailer entry shows
an overflow count of 19 missed entries.
hw_perf_event_update: sdbt 0xb5286070 full 1 over 19 flush_all:1
timestamp: 14:32:52.970058
Remove access to a follow on SDB when event overflow happened.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Function perf_event_ever_overflow() and perf_event_account_interrupt()
are called every time samples are processed by the interrupt handler.
However function perf_event_account_interrupt() has checks to avoid being
flooded with interrupts (more then 1000 samples are received per
task_tick). Samples are then dropped and a PERF_RECORD_THROTTLED is
added to the perf data. The perf subsystem limit calculation is:
maximum sample frequency := 100000 --> 1 samples per 10 us
task_tick = 10ms = 10000us --> 1000 samples per task_tick
The work flow is
measurement_alert() uses SDBT head and each SBDT points to 511
SDB pages, each with 126 sample entries. After processing 8 SBDs
and for each valid sample calling:
there is a considerable amount of samples being dropped, especially when
the sample frequency is very high and near the 100000 limit.
To avoid the high amount of samples being dropped near the end of a
task_tick time frame, increment the sampling interval in case of
dropped events. The CPU Measurement sampling facility on the s390
supports only intervals, specifiing how many CPU cycles have to be
executed before a sample is generated. Increase the interval when the
samples being generated hit the task_tick limit.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In raid1_sync_request func, rdev should be checked before reference.
Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fix the lookup method on the dynamic root directory such that creation
calls, such as mkdir, open(O_CREAT), symlink, etc. fail with EOPNOTSUPP
rather than failing with some odd error (such as EEXIST).
lookup() itself tries to create automount directories when it is invoked.
These are cached locally in RAM and not committed to storage.
Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com> Tested-by: Jonathan Billings <jsbillings@jsbillings.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The socket read/write helpers only look at the file O_NONBLOCK. not
the iocb IOCB_NOWAIT flag. This breaks users like preadv2/pwritev2
and io_uring that rely on not having the file itself marked nonblocking,
but rather the iocb itself.
Cc: netdev@vger.kernel.org Acked-by: David Miller <davem@davemloft.net> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Gadget driver should always use config_ep_by_speed() to initialize
usb_ep struct according to usb device's operating speed. Otherwise,
usb_ep struct may be wrong if usb devcie's operating speed is changed.
The key point in this patch is that we want to make sure the desc pointer
in usb_ep struct will be set to NULL when gadget is disconnected.
This will force it to call config_ep_by_speed() to correctly initialize
usb_ep struct based on the new operating speed when gadget is
re-connected later.
Reviewed-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: EJ Hsu <ejh@nvidia.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Place the declaration of struct nouveau_conn_atom above that of
struct nouveau_connector. This commit makes no changes to the moved
block what so ever, it just moves it up a bit.
This is a preparation patch to fix some issues with connector handling
on pre nv50 displays (which do not use atomic modesetting).
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On this error path we call qla4xxx_mem_free() and then the caller also
calls qla4xxx_free_adapter() which calls qla4xxx_mem_free(). It leads to a
couple double frees:
PORT UPDATE asynchronous event is generated on the host that issues PLOGI
ELS (in the case of higher WWPN). In that case, the event shouldn't be
handled as it sets unwanted DPC flags (i.e. LOOP_RESYNC_NEEDED) that
trigger link flap.
Ignore the event if the host has higher WWPN, but handle otherwise.
Cc: Quinn Tran <qutran@marvell.com> Link: https://lore.kernel.org/r/20191125165702.1013-13-r.bolshakov@yadro.com Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
qlt_handle_login schedules session for deletion even if a login is in
progress. That causes login bouncing, i.e. a few logins are made before it
settles down.
Complete the first login by sending Notify Acknowledge IOCB via
qlt_plogi_ack_unref if the session is pending login completion.
Fixes: 9cd883f07a54 ("scsi: qla2xxx: Fix session cleanup for N2N") Cc: Krishna Kant <krishna.kant@purestorage.com> Cc: Alexei Potashnik <alexei@purestorage.com> Link: https://lore.kernel.org/r/20191125165702.1013-11-r.bolshakov@yadro.com Acked-by: Quinn Tran <qutran@marvell.com> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
qla2x00_configure_local_loop initializes PLOGI payload for PLOGI ELS using
Get Parameters mailbox command.
In the case when the driver is running in target mode, the topology is N2N
and the target port has higher WWPN, LOCAL_LOOP_UPDATE bit is cleared too
early and PLOGI payload is not initialized by the Get Parameters
command. That causes a failure of ELS IOCB carrying the PLOGI with 0x15 aka
Data Underrun error.
LOCAL_LOOP_UPDATE has to be set to initialize PLOGI payload.
Fixes: 48acad099074 ("scsi: qla2xxx: Fix N2N link re-connect") Link: https://lore.kernel.org/r/20191125165702.1013-10-r.bolshakov@yadro.com Acked-by: Quinn Tran <qutran@marvell.com> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The size of the buffer is hardcoded as 0x70 or 112 bytes, while the size of
ELS IOCB is 0x40 and the size of PLOGI payload returned by Get Parameters
command is 0x74.
Cc: Quinn Tran <qutran@marvell.com> Link: https://lore.kernel.org/r/20191125165702.1013-9-r.bolshakov@yadro.com Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
MBA_PORT_UPDATE generates duplicate log lines in target mode because
qlt_async_event is called twice. Drop the calls within the case as the
function will be called right after the switch statement.
Cc: Quinn Tran <qutran@marvell.com> Link: https://lore.kernel.org/r/20191125165702.1013-8-r.bolshakov@yadro.com Acked-by: Himanshu Madhani <hmadhani@marvel.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
del_work is already initialized inside qla2x00_alloc_fcport, there's no
need to overwrite it. Indeed, it might prevent complete traversal of
workqueue list.
Fixes: a01c77d2cbc45 ("scsi: qla2xxx: Move session delete to driver work queue") Cc: Quinn Tran <qutran@marvell.com> Link: https://lore.kernel.org/r/20191125165702.1013-5-r.bolshakov@yadro.com Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If RoCE PDUs being sent or received contain pad bytes, then the iCRC
is miscalculated, resulting in PDUs being emitted by RXE with an incorrect
iCRC, as well as ingress PDUs being dropped due to erroneously detecting
a bad iCRC in the PDU. The fix is to include the pad bytes, if any,
in iCRC computations.
Note: This bug has caused broken on-the-wire compatibility with actual
hardware RoCE devices since the soft-RoCE driver was first put into the
mainstream kernel. Fixing it will create an incompatibility with the
original soft-RoCE devices, but is necessary to be compatible with real
hardware devices.
Fixes: 8700e3e7c485 ("Soft RoCE driver") Signed-off-by: Steve Wise <larrystevenwise@gmail.com> Link: https://lore.kernel.org/r/20191203020319.15036-2-larrystevenwise@gmail.com Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Make the AFS dynamic root superblock R/W so that SELinux can set the
security label on it. Without this, upgrades to, say, the Fedora
filesystem-afs RPM fail if afs is mounted on it because the SELinux label
can't be (re-)applied.
It might be better to make it possible to bypass the R/O check for LSM
label application through setxattr.
Fixes: 4d673da14533 ("afs: Support the AFS dynamic root") Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: selinux@vger.kernel.org
cc: linux-security-module@vger.kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
afs_find_server tries to find a server that has an address that
matches the transport address of an rxrpc peer. The code assumes
that the transport address is always ipv6, with ipv4 represented
as ipv4 mapped addresses, but that's not the case. If the transport
family is AF_INET, srx->transport.sin6.sin6_addr.s6_addr32[] will
be beyond the actual ipv4 address and will always be 0, and all
ipv4 addresses will be seen as matching.
As a result, the first ipv4 address seen on any server will be
considered a match, and the server returned may be the wrong one.
One of the consequences is that callbacks received over ipv4 will
only be correctly applied for the server that happens to have the
first ipv4 address on the fs_addresses4 list. Callbacks over ipv4
from all other servers are dropped, causing the client to serve stale
data.
This is fixed by looking at the transport family, and comparing ipv4
addresses based on a sockaddr_in structure rather than a sockaddr_in6.
Fixes: d2ddc776a458 ("afs: Overhaul volume and server record caching and fileserver rotation") Signed-off-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Right now devfreq_dev_release will print a warning and abort the rest of
the cleanup if the devfreq instance is not part of the global
devfreq_list. But this is a valid scenario, for example it can happen if
the governor can't be found or on any other init error that happens
after device_register.
Initialize devfreq->node to an empty list head in devfreq_add_device so
that list_del becomes a safe noop inside devfreq_dev_release and we can
continue the rest of the cleanup.
The devfreq_notifier_call functions will update scaling_min_freq and
scaling_max_freq when the OPP table is updated.
If fetching the maximum frequency fails then scaling_max_freq remains
set to zero which is confusing. Set to ULONG_MAX instead so we don't
need special handling for this case in other places.
As of commit b9ddd5091160793e ("iio: adc: max9611: Fix temperature
reading in probe"), max9611 initialization sometimes fails on the
Salvator-X(S) development board with:
max9611 4-007f: Invalid value received from ADC 0x8000: aborting
max9611: probe of 4-007f failed with error -5
The max9611 driver tests communications with the chip by reading the die
temperature during the probe function, which returns an invalid value.
According to the datasheet, the typical ADC conversion time is 2 ms, but
no minimum or maximum values are provided. Maxim Technical Support
confirmed this was tested with temperature Ta=25 degreeC, and promised
to inform me if a maximum/minimum value is available (they didn't get
back to me, so I assume it is not).
However, the driver assumes a 1 ms conversion time. Usually the
usleep_range() call returns after more than 1.8 ms, hence it succeeds.
When it returns earlier, the data register may be read too early, and
the previous measurement value will be returned. After boot, this is
the temperature POR (power-on reset) value, causing the failure above.
Fix this by increasing the delay from 1000-2000 µs to 3000-3300 µs.
Note that this issue has always been present, but it was exposed by the
aformentioned commit.
[Why]
In dc_link_is_dp_sink_present, if dal_ddc_open fails, then
dal_gpio_destroy_ddc is called, destroying pin_data and pin_clock. They
are created only on dc_construct, and next aux access will cause a panic.
[How]
Instead of calling dal_gpio_destroy_ddc, call dal_ddc_close.
Signed-off-by: David Galiffi <David.Galiffi@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When security violation from new vbios happens, data fabric is
risky to stop working. So prevent the direct access to DF
mmFabricConfigAccessControl from the new vbios and onwards.
If an error occurs on one of the ios used for creating an
association, the creating routine has error paths that are
invoked by the command failure and the error paths will free
up the controller resources created to that point.
But... the io was ultimately determined by an asynchronous
completion routine that detected the error and which
unconditionally invokes the error_recovery path which calls
delete_association. Delete association deletes all outstanding
io then tears down the controller resources. So the
create_association thread can be running in parallel with
the error_recovery thread. What was seen was the LLDD received
a call to delete a queue, causing the LLDD to do a free of a
resource, then the transport called the delete queue again
causing the driver to repeat the free call. The second free
routine corrupted the allocator. The transport shouldn't be
making the duplicate call, and the delete queue is just one
of the resources being freed.
To fix, it is realized that the create_association path is
completely serialized with one command at a time. So the
failed io completion will always be seen by the create_association
path and as of the failure, there are no ios to terminate and there
is no reason to be manipulating queue freeze states, etc.
The serialized condition stays true until the controller is
transitioned to the LIVE state. Thus the fix is to change the
error recovery path to check the controller state and only
invoke the teardown path if not already in the CONNECTING state.
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In nvme-fc: it's possible to have connected active controllers
and as no references are taken on the LLDD, the LLDD can be
unloaded. The controller would enter a reconnect state and as
long as the LLDD resumed within the reconnect timeout, the
controller would resume. But if a namespace on the controller
is the root device, allowing the driver to unload can be problematic.
To reload the driver, it may require new io to the boot device,
and as it's no longer connected we get into a catch-22 that
eventually fails, and the system locks up.
Fix this issue by taking a module reference for every connected
controller (which is what the core layer did to the transport
module). Reference is cleared when the controller is removed.
Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1862263
"ctx:file_pos sysctl:read write ok" fails on s390 with "Read value !=
nux". This is because verifier rewrites a complete 32-bit
bpf_sysctl.file_pos update to a partial update of the first 32 bits of
64-bit *bpf_sysctl_kern.ppos, which is not correct on big-endian
systems.
Fix by using an offset on big-endian systems.
Ditto for bpf_sysctl.file_pos reads. Currently the test does not detect
a problem there, since it expects to see 0, which it gets with high
probability in error cases, so change it to seek to offset 3 and expect
3 in bpf_sysctl.file_pos.
Fixes: e1550bfe0de4 ("bpf: Add file_pos field to bpf_sysctl ctx") Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com> Acked-by: Yonghong Song <yhs@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20190816105300.49035-1-iii@linux.ibm.com/
(cherry picked from commit d895a0f16fadb26d22ab531c49768f7642ae5c3e) Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
UBUNTU: SAUCE: shiftfs: prevent lower dentries from going negative during unlink
BugLink: https://bugs.launchpad.net/bugs/1860041
All non-special files (For shiftfs this only includes fifos and - for
this case - unix sockets - since we don't allow character and block
devices to be created.) go through shiftfs_open() and have their dentry
pinned through this codepath preventing it from going negative. But
fifos don't use the shiftfs fops but rather use the pipefifo_fops which
means they do not go through shiftfs_open() and thus don't have their
dentry pinned that way. Thus, the lower dentries for such files can go
negative on unlink causing segfaults. The following C program can be
used to reproduce the crash:
AceLan Kao [Wed, 12 Feb 2020 06:53:15 +0000 (14:53 +0800)]
UBUNTU: SAUCE: platform/x86: dell-uart-backlight: increase retry times
BugLink: https://bugs.launchpad.net/bugs/1862885
From ODM, scalar takes some time to activate panel during booting up,
it can't respond the UART commands within 1 seconds.
So, we add retry and wait 2 seconds for the response. But sometimes it
still fails to read the response.
During the boot up time, it sometimes takes more than 2 seconds to respond
the first command, so we enlarge the retry timeout from 2 seconds to 5
seconds to make sure we get the first response from scalar.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com> Acked-By: You-Sheng Yang <vicamo.yang@canonical.com> Acked-by: Anthony Wong <anthony.wong@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Andrew Murray [Fri, 31 Jan 2020 15:15:44 +0000 (12:15 -0300)]
KVM: arm64: Write arch.mdcr_el2 changes since last vcpu_load on VHE
BugLink: https://bugs.launchpad.net/bugs/1860657
On VHE systems arch.mdcr_el2 is written to mdcr_el2 at vcpu_load time to
set options for self-hosted debug and the performance monitors
extension.
Unfortunately the value of arch.mdcr_el2 is not calculated until
kvm_arm_setup_debug() in the run loop after the vcpu has been loaded.
This means that the initial brief iterations of the run loop use a zero
value of mdcr_el2 - until the vcpu is preempted. This also results in a
delay between changes to vcpu->guest_debug taking effect.
Fix this by writing to mdcr_el2 in kvm_arm_setup_debug() on VHE systems
when a change to arch.mdcr_el2 has been detected.
Fixes: d5a21bcc2995 ("KVM: arm64: Move common VHE/non-VHE trap config in separate functions") Cc: <stable@vger.kernel.org> # 4.17.x- Suggested-by: James Morse <james.morse@arm.com> Acked-by: Will Deacon <will@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Andrew Murray <andrew.murray@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit 4942dc6638b07b5326b6d2faa142635c559e7cd5) Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
can, slip: Protect tty->disc_data in write_wakeup and close with RCU
BugLink: https://bugs.launchpad.net/bugs/1862114
write_wakeup can happen in parallel with close/hangup where tty->disc_data
is set to NULL and the netdevice is freed thus also freeing
disc_data. write_wakeup accesses disc_data so we must prevent close from
freeing the netdev while write_wakeup has a non-NULL view of
tty->disc_data.
We also need to make sure that accesses to disc_data are atomic. Which can
all be done with RCU.
This problem was found by Syzkaller on SLCAN, but the same issue is
reproducible with the SLIP line discipline using an LTP test based on the
Syzkaller reproducer.
A fix which didn't use RCU was posted by Hillf Danton.
Fixes: 661f7fda21b1 ("slip: Fix deadlock in write_wakeup") Fixes: a8e83b17536a ("slcan: Port write_wakeup deadlock fix from slip") Reported-by: syzbot+017e491ae13c0068598a@syzkaller.appspotmail.com Signed-off-by: Richard Palethorpe <rpalethorpe@suse.com> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: "David S. Miller" <davem@davemloft.net> Cc: Tyler Hall <tylerwhall@gmail.com> Cc: linux-can@vger.kernel.org Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: syzkaller@googlegroups.com Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 0ace17d56824165c7f4c68785d6b58971db954dd) Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1860248
In case system has multiple HDA controllers, it can happen that
same HDA codec driver is used for codecs of multiple controllers.
In this case, SOF may fail to probe the HDA driver and SOF
initialization fails.
SOF HDA code currently relies that a call to request_module() will
also run device matching logic to attach driver to the codec instance.
However if driver for another HDA controller was already loaded and it
already loaded the HDA codec driver, this breaks current logic in SOF.
In this case the request_module() SOF does becomes a no-op and HDA
Codec driver is not attached to the codec instance sitting on the HDA
bus SOF is controlling. Typical scenario would be a system with both
external and internal GPUs, with driver of the external GPU loaded
first.
Fix this by adding similar logic as is used in legacy HDA driver
where an explicit device_attach() call is done after request_module().
Also add logic to propagate errors reported by device_attach() back
to caller. This also works in the case where drivers are not built
as modules.
Because ocfs2_get_dlm_debug() function is called once less here, ocfs2
file system will trigger the system crash, usually after ocfs2 file
system is unmounted.
This system crash is caused by a generic memory corruption, these crash
backtraces are not always the same, for exapmle,
This regression problem was introduced by commit e581595ea29c ("ocfs: no
need to check return value of debugfs_create functions").
Link: http://lkml.kernel.org/r/20191225061501.13587-1-ghe@suse.com Fixes: e581595ea29c ("ocfs: no need to check return value of debugfs_create functions") Signed-off-by: Gang He <ghe@suse.com> Acked-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> [5.3+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(backported from commit b73eba2a867e10b9b4477738677341f3307c07bb linux) Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Rafael David Tinoco <rafaeldtinoco@ubuntu.com> Signed-off-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com>
When we readd /dev/sda to the array, it started to do recovery.
After offline the other two disks in md1, the recovery have
been interrupted and superblock update info cannot be written
to the offline disks. While the spare disk (/dev/sda) can continue
to update superblock info.
After stopping the array and assemble it, we found the array
run fail, with the follow kernel message:
[ 172.986064] md: kicking non-fresh sdb from array!
[ 173.004210] md: kicking non-fresh sdc from array!
[ 173.022383] md/raid1:md1: active with 0 out of 4 mirrors
[ 173.022406] md1: failed to create bitmap (-5)
[ 173.023466] md: md1 stopped.
Since both sdb and sdc have the value of 'sb->events' smaller than
that in sda, they have been kicked from the array. However, the only
remained disk sda is in 'spare' state before stop and it cannot be
added to conf->mirrors[] array. In the end, raid array assemble
and run fail.
In fact, we can use the older disk sdb or sdc to assemble the array.
That means we should not choose the 'spare' disk as the fresh disk in
analyze_sbs().
To fix the problem, we do not compare superblock events when it is
a spare disk, as same as validate_super.
Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Jason Yan [Fri, 24 Jan 2020 11:23:48 +0000 (13:23 +0200)]
scsi: libsas: stop discovering if oob mode is disconnected
The discovering of sas port is driven by workqueue in libsas. When libsas
is processing port events or phy events in workqueue, new events may rise
up and change the state of some structures such as asd_sas_phy. This may
cause some problems such as follows:
==>thread 1 ==>thread 2
==>phy up
==>phy_up_v3_hw()
==>oob_mode = SATA_OOB_MODE;
==>phy down quickly
==>hisi_sas_phy_down()
==>sas_ha->notify_phy_event()
==>sas_phy_disconnected()
==>oob_mode = OOB_NOT_CONNECTED
==>workqueue wakeup
==>sas_form_port()
==>sas_discover_domain()
==>sas_get_port_device()
==>oob_mode is OOB_NOT_CONNECTED and device
is wrongly taken as expander
This at last lead to the panic when libsas trying to issue a command to
discover the device.
Fixes: 2908d778ab3e ("[SCSI] aic94xx: new driver") Link: https://lore.kernel.org/r/20191206011118.46909-1-yanaijie@huawei.com Reported-by: Gao Chuan <gaochuan4@huawei.com> Reviewed-by: John Garry <john.garry@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
CVE-2019-19965
(cherry picked from commit f70267f379b5e5e11bdc5d72a56bf17e5feed01f) Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The problem is the check introduced to for_each_hstate() loop that
should skip default_hstate_idx. Since it doesn't update 'i' counter,
all subsequent huge page sizes are skipped as well.
Fixes: 8fc312b32b25 ("mm/hugetlbfs: fix error handling when setting up mounts") Signed-off-by: Jan Stancek <jstancek@redhat.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A previous patch implemented an incomplete workaround of erratum
A-008171. The complete workaround is as below. This patch is to
implement the complete workaround which uses SW tuning if HW tuning
fails, and retries both HW/SW tuning once with reduced clock if
workaround fails. This is suggested by hardware team, and the patch
had been verified on LS1046A eSDHC + Phison 32G eMMC which could
trigger the erratum.
Workaround:
/* For T1040, T2080, LS1021A, T1023 Rev 1: */
1. Program TBPTR[TB_WNDW_END_PTR] = 3*DIV_RATIO.
2. Program TBPTR[TB_WNDW_START_PTR] = 5*DIV_RATIO.
3. Program the software tuning mode by setting TBCTL[TB_MODE] = 2'h3.
4. Set SYSCTL2[EXTN] and SYSCTL2[SAMPCLKSEL].
5. Issue SEND_TUNING_BLK Command (CMD19 for SD, CMD21 for MMC).
6. Wait for IRQSTAT[BRR], buffer read ready, to be set.
7. Clear IRQSTAT[BRR].
8. Check SYSCTL2[EXTN] to be cleared.
9. Check SYSCTL2[SAMPCLKSEL], Sampling Clock Select. It's set value
indicate tuning procedure success, and clear indicate failure.
In case of tuning failure, fixed sampling scheme could be used by
clearing TBCTL[TB_EN].
/* For LS1080A Rev 1, LS2088A Rev 1.0, LA1575A Rev 1.0: */
1. Read the TBCTL[31:0] register. Write TBCTL[11:8]=4'h8 and wait for
1ms.
2. Read the TBCTL[31:0] register and rewrite again. Wait for 1ms second.
3. Read the TBSTAT[31:0] register twice.
3.1 Reset data lines by setting ESDHCCTL[RSTD] bit.
3.2 Check ESDHCCTL[RSTD] bit.
3.3 If ESDHCCTL[RSTD] is 0, go to step 3.4 else go to step 3.2.
3.4 Write 32'hFFFF_FFFF to IRQSTAT register.
4. if TBSTAT[15:8]-TBSTAT[7:0] > 4*DIV_RATIO or TBSTAT[7:0]-TBSTAT[15:8]
> 4*DIV_RATIO , then program TBPTR[TB_WNDW_END_PTR] = 4*DIV_RATIO and
program TBPTR[TB_WNDW_START_PTR] = 8*DIV_RATIO.
/* For LS1012A Rev1, LS1043A Rev 1.x, LS1046A 1.0: */
1. Read the TBCTL[0:31] register. Write TBCTL[20:23]=4'h8 and wait for
1ms.
2. Read the TBCTL[0:31] register and rewrite again. Wait for 1ms second.
3. Read the TBSTAT[0:31] register twice.
3.1 Reset data lines by setting ESDHCCTL[RSTD] bit.
3.2 Check ESDHCCTL[RSTD] bit.
3.3 If ESDHCCTL[RSTD] is 0, go to step 3.4 else go to step 3.2.
3.4 Write 32'hFFFF_FFFF to IRQSTAT register.
4. if TBSTAT[16:23]-TBSTAT[24:31] > 4*DIV_RATIO or TBSTAT[24:31]-
TBSTAT[16:23] > 4* DIV_RATIO , then program TBPTR[TB_WNDW_END_PTR] =
4*DIV_RATIO and program TBPTR[TB_WNDW_START_PTR] = 8*DIV_RATIO.
/* For LS1080A Rev 1, LS2088A Rev 1.0, LA1575A Rev 1.0 LS1012A Rev1,
* LS1043A Rev 1.x, LS1046A 1.0:
*/
5. else program TBPTR[TB_WNDW_END_PTR] = 3*DIV_RATIO and program
TBPTR[TB_WNDW_START_PTR] = 5*DIV_RATIO.
6. Program the software tuning mode by setting TBCTL[TB_MODE] = 2'h3.
7. Set SYSCTL2[EXTN], wait 1us and SYSCTL2[SAMPCLKSEL].
8. Issue SEND_TUNING_BLK Command (CMD19 for SD, CMD21 for MMC).
9. Wait for IRQSTAT[BRR], buffer read ready, to be set.
10. Clear IRQSTAT[BRR].
11. Check SYSCTL2[EXTN] to be cleared.
12. Check SYSCTL2[SAMPCLKSEL], Sampling Clock Select. It's set value
indicate tuning procedure success, and clear indicate failure.
In case of tuning failure, fixed sampling scheme could be used by
clearing TBCTL[TB_EN].
In commit 4b1373de73a3 ("net: ipv6: addr: perform strict checks also for
doit handlers") we add strict check for inet6_rtm_getaddr(). But we did
the invalid header values check before checking if NETLINK_F_STRICT_CHK
is set. This may break backwards compatibility if user already set the
ifm->ifa_prefixlen, ifm->ifa_flags, ifm->ifa_scope in their netlink code.
I didn't move the nlmsg_len check because I thought it's a valid check.
Reported-by: Jianlin Shi <jishi@redhat.com> Fixes: 4b1373de73a3 ("net: ipv6: addr: perform strict checks also for doit handlers") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
After executing "ethtool -C eth0 rx-usecs-irq 0", the box becomes
unresponsive, likely due to interrupt livelock. It appears that
a minimum clamp value for the irq timer is computed, but is never
applied.
Fix by applying the corrected clamp value.
Fixes: 74706afa712d ("bnxt_en: Update interrupt coalescing logic.") Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Host can provide send indirection table messages anytime after RSS is
enabled by calling rndis_filter_set_rss_param(). So the host provided
table values may be overwritten by the initialization in
rndis_set_subchannel().
To prevent this problem, move the tx_table initialization before calling
rndis_filter_set_rss_param().
Fixes: a6fb6aa3cfa9 ("hv_netvsc: Set tx_table to equal weight after subchannels open") Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For first-generation switches (SJA1105E and SJA1105T):
- TPID means C-Tag (typically 0x8100)
- TPID2 means S-Tag (typically 0x88A8)
While for the second generation switches (SJA1105P, SJA1105Q, SJA1105R,
SJA1105S) it is the other way around:
- TPID means S-Tag (typically 0x88A8)
- TPID2 means C-Tag (typically 0x8100)
In other words, E/T tags untagged traffic with TPID, and P/Q/R/S with
TPID2.
So the patch mentioned below fixed VLAN filtering for P/Q/R/S, but broke
it for E/T.
We strive for a common code path for all switches in the family, so just
lie in the static config packing functions that TPID and TPID2 are at
swapped bit offsets than they actually are, for P/Q/R/S. This will make
both switches understand TPID to be ETH_P_8021Q and TPID2 to be
ETH_P_8021AD. The meaning from the original E/T was chosen over P/Q/R/S
because E/T is actually the one with public documentation available
(UM10944.pdf).
Fixes: f9a1a7646c0d ("net: dsa: sja1105: Reverse TPID and TPID2") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently, VRRP packets and packets that hit exceptions during routing
(e.g., MTU error) are policed using the same policer towards the CPU.
This means, for example, that misconfiguration of the MTU on a routed
interface can prevent VRRP packets from reaching the CPU, which in turn
can cause the VRRP daemon to assume it is the Master router.
Fix this by using a dedicated policer for VRRP packets.
Fixes: 11566d34f895 ("mlxsw: spectrum: Add VRRP traps") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Alex Veber <alexve@mellanox.com> Tested-by: Alex Veber <alexve@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a router interface (RIF) is created the MAC address of the backing
netdev is verified to have the same MSBs as existing RIFs. This is
required in order to avoid changing existing RIF MAC addresses that all
share the same MSBs.
Loopback RIFs are special in this regard as they do not have a MAC
address, given they are only used to loop packets from the overlay to
the underlay.
Without this change, an error is returned when trying to create a RIF
after the creation of a GRE tunnel that is represented by a loopback
RIF. 'rif->dev->dev_addr' points to the GRE device's local IP, which
does not share the same MSBs as physical interfaces. Adding an IP
address to any physical interface results in:
Error: mlxsw_spectrum: All router interface MAC addresses must have the
same prefix.
Fix this by skipping loopback RIFs during MAC validation.
Fixes: 74bc99397438 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses") Signed-off-by: Amit Cohen <amitc@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If any change happened in the configuration of VF in VM while
collecting live dump, there could be a race and firmware can return
more data than allocated dump length. Fix it by keeping track of
the accumulated core dump length copied so far and abort the copy
with error code if the next chunk of core dump will exceed the
original dump length.
Fixes: 6c5657d085ae ("bnxt_en: Add support for ethtool get dump.") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The logic needs to check both bp->total_irqs and the reserved IRQs in
hw_resc->resv_irqs if applicable and see if both are enough to cover
the L2 and RDMA requested vectors. The current code is only checking
bp->total_irqs and can fail in some code paths, such as the TX timeout
code path with the RDMA driver requesting vectors after recovery. In
this code path, we have not reserved enough MSIX resources for the
RDMA driver yet.
Fixes: 75720e6323a1 ("bnxt_en: Keep track of reserved IRQs.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If fq_classify() recycles a struct fq_flow because
a socket structure has been reallocated, we do not
set sk->sk_pacing_status immediately, but later if the
flow becomes detached.
This means that any flow requiring pacing (BBR, or SO_MAX_PACING_RATE)
might fallback to TCP internal pacing, which requires a per-socket
high resolution timer, and therefore more cpu cycles.
Fixes: 218af599fa63 ("tcp: internal implementation for pacing") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Soheil Hassas Yeganeh <soheil@google.com> Cc: Neal Cardwell <ncardwell@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Revert "net/sched: cls_u32: fix refcount leak in the error path of
u32_change()", and fix the u32 refcount leak in a more generic way that
preserves the semantic of rule dumping.
On tc filters that don't support lockless insertion/removal, there is no
need to guard against concurrent insertion when a removal is in progress.
Therefore, for most of them we can avoid a full walk() when deleting, and
just decrease the refcount, like it was done on older Linux kernels.
This fixes situations where walk() was wrongly detecting a non-empty
filter, like it happened with cls_u32 in the error path of change(), thus
leading to failures in the following tdc selftests:
6aa7: (filter, u32) Add/Replace u32 with source match and invalid indev
6658: (filter, u32) Add/Replace u32 with custom hash table and invalid handle
74c2: (filter, u32) Add/Replace u32 filter with invalid hash table id
On cls_flower, and on (future) lockless filters, this check is necessary:
move all the check_empty() logic in a callback so that each filter
can have its own implementation. For cls_flower, it's sufficient to check
if no IDRs have been allocated.
Changes since v1:
- document the need for delete_empty() when TCF_PROTO_OPS_DOIT_UNLOCKED
is used, thanks to Vlad Buslov
- implement delete_empty() without doing fl_walk(), thanks to Vlad Buslov
- squash revert and new fix in a single patch, to be nice with bisect
tests that run tdc on u32 filter, thanks to Dave Miller
Fixes: 275c44aa194b ("net/sched: cls_u32: fix refcount leak in the error path of u32_change()") Fixes: 6676d5e416ee ("net: sched: set dedicated tcf_walker flag when tp is empty") Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com> Suggested-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Reviewed-by: Vlad Buslov <vladbu@mellanox.com> Tested-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There's no skb_pull performed when a mirred action is set at egress of a
mac device, with a target device/action that expects skb->data to point
at the network header.
As a result, either the target device is errornously given an skb with
data pointing to the mac (egress case), or the net stack receives the
skb with data pointing to the mac (ingress case).
E.g:
# tc qdisc add dev eth9 root handle 1: prio
# tc filter add dev eth9 parent 1: prio 9 protocol ip handle 9 basic \
action mirred egress redirect dev tun0
(tun0 is a tun device. result: tun0 errornously gets the eth header
instead of the iph)
Revise the push/pull logic of tcf_mirred_act() to not rely on the
skb_at_tc_ingress() vs tcf_mirred_act_wants_ingress() comparison, as it
does not cover all "pull" cases.
Instead, calculate whether the required action on the target device
requires the data to point at the network header, and compare this to
whether skb->data points to network header - and make the push/pull
adjustments as necessary.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Shmulik Ladkani <sladkani@proofpoint.com> Tested-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The suspend/resume code for AQR107 works on AQR105 too.
This patch fixes issues with the partner not seeing the link down
when the interface using AQR105 is brought down.
Fixes: bee8259dd31f ("net: phy: add driver for aquantia phy") Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The IP fragment is specified through user-defined field as the first
bit of the first user-defined word. We were previously trying to extract
it from the user-defined mask which could not possibly work. The ip_frag
is also supposed to be a boolean, if we do not cast it as such, we risk
overwriting the next fields in CFP_DATA(6) which would render the rule
inoperative.
Fixes: 7318166cacad ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
As per 802.3-2005, Section Two, Annex 28B, Table 28B-2 [1], when
_only_ Rx pause is enabled, both symmetric and asymmetric pause
towards local device must be enabled. Also, firmware returns the local
device's flow control pause params as part of advertised capabilities
and negotiated params as part of current link attributes. So, fix up
ethtool's flow control pause params fetch logic to read from acaps,
instead of linkattr.
syzbot (via KASAN) reports a use-after-free in the error path of
xlog_alloc_log(). Specifically, the iclog freeing loop doesn't
handle the case of a fully initialized ->l_iclog linked list.
Instead, it assumes that the list is partially constructed and NULL
terminated.
This bug manifested because there was no possible error scenario
after iclog list setup when the original code was added. Subsequent
code and associated error conditions were added some time later,
while the original error handling code was never updated. Fix up the
error loop to terminate either on a NULL iclog or reaching the end
of the list.
Reported-by: syzbot+c732f8644185de340492@syzkaller.appspotmail.com Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
As we've done with VFS, string operations, etc, reject usercopy sizes
larger than INT_MAX, which would be nice to have for catching bugs
related to size calculation overflows[1].
This adds 10 bytes to x86_64 defconfig text and 1980 bytes to the data
section: