Vladimir Oltean [Tue, 14 Sep 2021 14:05:15 +0000 (17:05 +0300)]
Revert "net: phy: Uniform PHY driver access"
This reverts commit 3ac8eed62596387214869319379c1fcba264d8c6, which did
more than it said on the box, and not only it replaced to_phy_driver
with phydev->drv, but it also removed the "!drv" check, without actually
explaining why that is fine.
That patch in fact breaks suspend/resume on any system which has PHY
devices with no drivers bound.
The stack trace is:
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000e8
pc : mdio_bus_phy_suspend+0xd8/0xec
lr : dpm_run_callback+0x38/0x90
Call trace:
mdio_bus_phy_suspend+0xd8/0xec
dpm_run_callback+0x38/0x90
__device_suspend+0x108/0x3cc
dpm_suspend+0x140/0x210
dpm_suspend_start+0x7c/0xa0
suspend_devices_and_enter+0x13c/0x540
pm_suspend+0x2a4/0x330
Examples why that assumption is not fine:
- There is an MDIO bus with a PHY device that doesn't have a specific
PHY driver loaded, because mdiobus_register() automatically creates a
PHY device for it but there is no specific PHY driver in the system.
Normally under those circumstances, the generic PHY driver will be
bound lazily to it (at phy_attach_direct time). But some Ethernet
drivers attach to their PHY at .ndo_open time. Until then it, the
to-be-driven-by-genphy PHY device will not have a driver. The blamed
patch amounts to saying "you need to open all net devices before the
system can suspend, to avoid the NULL pointer dereference".
- There is any raw MDIO device which has 'plausible' values in the PHY
ID registers 2 and 3, which is located on an MDIO bus whose driver
does not set bus->phy_mask = ~0 (which prevents auto-scanning of PHY
devices). An example could be a MAC's internal MDIO bus with PCS
devices on it, for serial links such as SGMII. PHY devices will get
created for those PCSes too, due to that MDIO bus auto-scanning, and
although those PHY devices are not used, they do not bother anybody
either. PCS devices are usually managed in Linux as raw MDIO devices.
Nonetheless, they do not have a PHY driver, nor does anybody attempt
to connect to them (because they are not a PHY), and therefore this
patch breaks that.
The goal itself of the patch is questionable, so I am going for a
straight revert. to_phy_driver does not seem to have a need to be
replaced by phydev->drv, in fact that might even trigger code paths
which were not given too deep of a thought.
For instance:
phy_probe populates phydev->drv at the beginning, but does not clean it
up on any error (including EPROBE_DEFER). So if the phydev driver
requests probe deferral, phydev->drv will remain populated despite there
being no driver bound.
If a system suspend starts in between the initial probe deferral request
and the subsequent probe retry, we will be calling the phydev->drv->suspend
method, but _before_ any phydev->drv->probe call has succeeded.
That is to say, if the phydev->drv is allocating any driver-private data
structure in ->probe, it pretty much expects that data structure to be
available in ->suspend. But it may not. That is a pretty insane
environment to present to PHY drivers.
In the code structure before the blamed patch, mdio_bus_phy_may_suspend
would just say "no, don't suspend" to any PHY device which does not have
a driver pointer _in_the_device_structure_ (not the phydev->drv). That
would essentially ensure that ->suspend will never get called for a
device that has not yet successfully completed probe. This is the code
structure the patch is returning to, via the revert.
Vladimir Oltean [Tue, 14 Sep 2021 13:43:31 +0000 (16:43 +0300)]
net: dsa: destroy the phylink instance on any error in dsa_slave_phy_setup
DSA supports connecting to a phy-handle, and has a fallback to a non-OF
based method of connecting to an internal PHY on the switch's own MDIO
bus, if no phy-handle and no fixed-link nodes were present.
The -ENODEV error code from the first attempt (phylink_of_phy_connect)
is what triggers the second attempt (phylink_connect_phy).
However, when the first attempt returns a different error code than
-ENODEV, this results in an unbalance of calls to phylink_create and
phylink_destroy by the time we exit the function. The phylink instance
has leaked.
There are many other error codes that can be returned by
phylink_of_phy_connect. For example, phylink_validate returns -EINVAL.
So this is a practical issue too.
Fixes: aab9c4067d23 ("net: dsa: Plug in PHYLINK support") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20210914134331.2303380-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Randy Dunlap [Mon, 13 Sep 2021 22:06:05 +0000 (15:06 -0700)]
ptp: dp83640: don't define PAGE0
Building dp83640.c on arch/parisc/ produces a build warning for
PAGE0 being redefined. Since the macro is not used in the dp83640
driver, just make it a comment for documentation purposes.
In file included from ../drivers/net/phy/dp83640.c:23:
../drivers/net/phy/dp83640_reg.h:8: warning: "PAGE0" redefined
8 | #define PAGE0 0x0000
from ../drivers/net/phy/dp83640.c:11:
../arch/parisc/include/asm/page.h:187: note: this is the location of the previous definition
187 | #define PAGE0 ((struct zeropage *)__PAGE_OFFSET)
Fixes: cb646e2b02b2 ("ptp: Added a clock driver for the National Semiconductor PHYTER.") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Richard Cochran <richard.cochran@omicron.at> Cc: John Stultz <john.stultz@linaro.org> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Russell King <linux@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20210913220605.19682-1-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As mentioned in https://lkml.org/lkml/2021/9/13/1819
5 years old commit 919483096bfe ("ipv4: fix memory leaks in ip_cmsg_send() callers")
was a correct fix.
ip_cmsg_send() can loop over multiple cmsghdr()
If IP_RETOPTS has been successful, but following cmsghdr generates an error,
we do not free ipc.ok
If IP_RETOPTS is not successful, we have freed the allocated temporary space,
not the one currently in ipc.opt.
Sure, code could be refactored, but let's not bring back old bugs.
Fixes: d7807a9adf48 ("Revert "ipv4: fix memory leaks in ip_cmsg_send() callers"") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Yajun Deng <yajun.deng@linux.dev> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: fix tp->undo_retrans accounting in tcp_sacktag_one()
Commit 10d3be569243 ("tcp-tso: do not split TSO packets at retransmit
time") may directly retrans a multiple segments TSO/GSO packet without
split, Since this commit, we can no longer assume that a retransmitted
packet is a single segment.
This patch fixes the tp->undo_retrans accounting in tcp_sacktag_one()
that use the actual segments(pcount) of the retransmitted packet.
Before that commit (10d3be569243), the assumption underlying the
tp->undo_retrans-- seems correct.
Fixes: 10d3be569243 ("tcp-tso: do not split TSO packets at retransmit time") Signed-off-by: zhenggy <zhenggy@chinatelecom.cn> Reviewed-by: Eric Dumazet <edumazet@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following pull-request contains BPF updates for your *net* tree.
We've added 7 non-merge commits during the last 13 day(s) which contain
a total of 18 files changed, 334 insertions(+), 193 deletions(-).
The main changes are:
1) Fix mmap_lock lockdep splat in BPF stack map's build_id lookup, from Yonghong Song.
2) Fix BPF cgroup v2 program bypass upon net_cls/prio activation, from Daniel Borkmann.
3) Fix kvcalloc() BTF line info splat on oversized allocation attempts, from Bixuan Cui.
4) Fix BPF selftest build of task_pt_regs test for arm64/s390, from Jean-Philippe Brucker.
5) Fix BPF's disasm.{c,h} to dual-license so that it is aligned with bpftool given the former
is a build dependency for the latter, from Daniel Borkmann with ACKs from contributors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: cc36a070b590 ("net-caif: add CAIF netdevice") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Mon, 13 Sep 2021 23:07:59 +0000 (01:07 +0200)]
bpf, selftests: Add test case for mixed cgroup v1/v2
Minimal selftest which implements a small BPF policy program to the
connect(2) hook which rejects TCP connection requests to port 60123
with EPERM. This is being attached to a non-root cgroup v2 path. The
test asserts that this works under cgroup v2-only and under a mixed
cgroup v1/v2 environment where net_classid is set in the former case.
Minimal set of helpers for net_cls classid cgroupv1 management in order
to set an id, join from a process, initiate setup and teardown. cgroupv2
helpers are left as-is, but reused where possible.
Daniel Borkmann [Mon, 13 Sep 2021 23:07:57 +0000 (01:07 +0200)]
bpf, cgroups: Fix cgroup v2 fallback on v1/v2 mixed mode
Fix cgroup v1 interference when non-root cgroup v2 BPF programs are used.
Back in the days, commit bd1060a1d671 ("sock, cgroup: add sock->sk_cgroup")
embedded per-socket cgroup information into sock->sk_cgrp_data and in order
to save 8 bytes in struct sock made both mutually exclusive, that is, when
cgroup v1 socket tagging (e.g. net_cls/net_prio) is used, then cgroup v2
falls back to the root cgroup in sock_cgroup_ptr() (&cgrp_dfl_root.cgrp).
The assumption made was "there is no reason to mix the two and this is in line
with how legacy and v2 compatibility is handled" as stated in bd1060a1d671.
However, with Kubernetes more widely supporting cgroups v2 as well nowadays,
this assumption no longer holds, and the possibility of the v1/v2 mixed mode
with the v2 root fallback being hit becomes a real security issue.
Many of the cgroup v2 BPF programs are also used for policy enforcement, just
to pick _one_ example, that is, to programmatically deny socket related system
calls like connect(2) or bind(2). A v2 root fallback would implicitly cause
a policy bypass for the affected Pods.
In production environments, we have recently seen this case due to various
circumstances: i) a different 3rd party agent and/or ii) a container runtime
such as [0] in the user's environment configuring legacy cgroup v1 net_cls
tags, which triggered implicitly mentioned root fallback. Another case is
Kubernetes projects like kind [1] which create Kubernetes nodes in a container
and also add cgroup namespaces to the mix, meaning programs which are attached
to the cgroup v2 root of the cgroup namespace get attached to a non-root
cgroup v2 path from init namespace point of view. And the latter's root is
out of reach for agents on a kind Kubernetes node to configure. Meaning, any
entity on the node setting cgroup v1 net_cls tag will trigger the bypass
despite cgroup v2 BPF programs attached to the namespace root.
Generally, this mutual exclusiveness does not hold anymore in today's user
environments and makes cgroup v2 usage from BPF side fragile and unreliable.
This fix adds proper struct cgroup pointer for the cgroup v2 case to struct
sock_cgroup_data in order to address these issues; this implicitly also fixes
the tradeoffs being made back then with regards to races and refcount leaks
as stated in bd1060a1d671, and removes the fallback, so that cgroup v2 BPF
programs always operate as expected.
Bixuan Cui [Sat, 11 Sep 2021 00:55:57 +0000 (08:55 +0800)]
bpf: Add oversize check before call kvcalloc()
Commit 7661809d493b ("mm: don't allow oversized kvmalloc() calls") add the
oversize check. When the allocation is larger than what kmalloc() supports,
the following warning triggered:
net: hns3: fix the timing issue of VF clearing interrupt sources
Currently, the VF does not clear the interrupt source immediately after
receiving the interrupt. As a result, if the second interrupt task is
triggered when processing the first interrupt task, clearing the
interrupt source before exiting will clear the interrupt sources of the
two tasks at the same time. As a result, no interrupt is triggered for
the second task. The VF detects the missed message only when the next
interrupt is generated.
Clearing it immediately after executing check_evt_cause ensures that:
1. Even if two interrupt tasks are triggered at the same time, they can
be processed.
2. If the second task is triggered during the processing of the first
task and the interrupt source is not cleared, the interrupt is reported
after vector0 is enabled.
Fixes: b90fcc5bd904 ("net: hns3: add reset handling for VF when doing Core/Global/IMP reset") Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When the command for querying imp info is issued to the firmware,
if the firmware does not support the command, the returned value
of bd num is 0.
Add protection mechanism before alloc memory to prevent apply for
0-length memory.
Fixes: 0b198b0d80ea ("net: hns3: refactor dump m7 info of debugfs") Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yufeng Mo [Mon, 13 Sep 2021 13:08:23 +0000 (21:08 +0800)]
net: hns3: disable mac in flr process
The firmware will not disable mac in flr process. Therefore, the driver
needs to proactively disable mac during flr, which is the same as the
function reset.
Fixes: 35d93a30040c ("net: hns3: adjust the process of PF reset") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yufeng Mo [Mon, 13 Sep 2021 13:08:22 +0000 (21:08 +0800)]
net: hns3: change affinity_mask to numa node range
Currently, affinity_mask is set to a single cpu. As a result,
irqbalance becomes invalid in SUBSET or EXACT mode. To solve
this problem, change affinity_mask to numa node range. In this
way, irqbalance can be performed on the cpu of the numa node.
Fixes: 0812545487ec ("net: hns3: add interrupt affinity support for misc interrupt") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yufeng Mo [Mon, 13 Sep 2021 13:08:21 +0000 (21:08 +0800)]
net: hns3: pad the short tunnel frame before sending to hardware
The hardware cannot handle short tunnel frames below 65 bytes,
and will cause vlan tag missing problem. So pads packet size to
65 bytes for tunnel frames to fix this bug.
Fixes: 3db084d28dc0("net: hns3: Fix for vxlan tx checksum bug") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin [Mon, 13 Sep 2021 13:08:20 +0000 (21:08 +0800)]
net: hns3: add option to turn off page pool feature
When page pool is added to the hns3 driver, it is always
enabled unconditionally, which means spilt page handling
in the hns3 driver is dead code.
As there is a requirement to test the performance between
spilt page handling in driver and page pool, so add a module
param to support disabling the page pool.
When the page pool is proved to perform better in most case,
the spilt page handling in driver can be removed.
Fixes: 93188e9642c3 ("net: hns3: support skb's frag page recycling based on page pool") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The delay is especially needed by the xRX300 and xRX330 SoCs. Without
this patch, some phys are sometimes not properly detected.
The patch was tested on BT Home Hub 5A and D-Link DWR-966.
Fixes: a09d042b0862 ("net: dsa: lantiq: allow to use all GPHYs on xRX300 and xRX330") Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Hoang Le [Mon, 13 Sep 2021 09:28:52 +0000 (16:28 +0700)]
tipc: increase timeout in tipc_sk_enqueue()
In tipc_sk_enqueue() we use hardcoded 2 jiffies to extract
socket buffer from generic queue to particular socket.
The 2 jiffies is too short in case there are other high priority
tasks get CPU cycles for multiple jiffies update. As result, no
buffer could be enqueued to particular socket.
To solve this, we switch to use constant timeout 20msecs.
Then, the function will be expired between 2 jiffies (CONFIG_100HZ)
and 20 jiffies (CONFIG_1000HZ).
Fixes: c637c1035534 ("tipc: resolve race problem at unicast message reception") Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Aya Levin [Mon, 13 Sep 2021 07:53:49 +0000 (10:53 +0300)]
udp_tunnel: Fix udp_tunnel_nic work-queue type
Turn udp_tunnel_nic work-queue to an ordered work-queue. This queue
holds the UDP-tunnel configuration commands of the different netdevs.
When the netdevs are functions of the same NIC the order of
execution may be crucial.
Problem example:
NIC with 2 PFs, both PFs declare offload quota of up to 3 UDP-ports.
$ifconfig eth2 1.1.1.1/16 up
$ip link add eth2_19503 type vxlan id 5049 remote 1.1.1.2 dev eth2 dstport 19053
$ip link set dev eth2_19503 up
$ip link add eth2_19504 type vxlan id 5049 remote 1.1.1.3 dev eth2 dstport 19054
$ip link set dev eth2_19504 up
$ip link add eth2_19505 type vxlan id 5049 remote 1.1.1.4 dev eth2 dstport 19055
$ip link set dev eth2_19505 up
$ip link add eth2_19506 type vxlan id 5049 remote 1.1.1.5 dev eth2 dstport 19056
$ip link set dev eth2_19506 up
NIC RX port offload infrastructure offloads the first 3 UDP-ports (on
all devices which sets NETIF_F_RX_UDP_TUNNEL_PORT feature) and not
UDP-port 19056. So both PFs gets this offload configuration.
$ip link set dev eth2_19504 down
This triggers udp-tunnel-core to remove the UDP-port 19504 from
offload-ports-list and offload UDP-port 19056 instead.
In this scenario it is important that the UDP-port of 19504 will be
removed from both PFs before trying to add UDP-port 19056. The NIC can
stop offloading a UDP-port only when all references are removed.
Otherwise the NIC may report exceeding of the offload quota.
Fixes: cc4e3835eff4 ("udp_tunnel: add central NIC RX port offload infrastructure") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There is only when ip_options_get() return zero need to free.
It already called kfree() when return error.
Fixes: 919483096bfe ("ipv4: fix memory leaks in ip_cmsg_send() callers") Signed-off-by: Yajun Deng <yajun.deng@linux.dev> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 13 Sep 2021 11:31:13 +0000 (12:31 +0100)]
Merge branch 'bnxt_en-fixes'
Michael Chan says:
====================
bnxt_en: Bug fixes.
The first patch fixes an error recovery regression just introduced
about a week ago. The other two patches fix issues related to
freeing rings in the bnxt_close() path under error conditions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sun, 12 Sep 2021 16:34:49 +0000 (12:34 -0400)]
bnxt_en: Clean up completion ring page arrays completely
We recently changed the completion ring page arrays to be dynamically
allocated to better support the expanded range of ring depths. The
cleanup path for this was not quite complete. It might cause the
shutdown path to crash if we need to abort before the completion ring
arrays have been allocated and initialized.
Fix it by initializing the ring_mem->pg_arr to NULL after freeing the
completion ring page array. Add a check in bnxt_free_ring() to skip
referencing the rmem->pg_arr if it is NULL.
Fixes: 03c7448790b8 ("bnxt_en: Don't use static arrays for completion ring pages") Reviewed-by: Andy Gospodarek <gospo@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en: make bnxt_free_skbs() safe to call after bnxt_free_mem()
The call to bnxt_free_mem(..., false) in the bnxt_half_open_nic() error
path will deallocate ring descriptor memory via bnxt_free_?x_rings(),
but because irq_re_init is false, the ring info itself is not freed.
To simplify error paths, deallocation functions have generally been
written to be safe when called on unallocated memory. It should always
be safe to call dev_close(), which calls bnxt_free_skbs() a second time,
even in this semi- allocated ring state.
Calling bnxt_free_skbs() a second time with the rings already freed will
cause NULL pointer dereference. Fix it by checking the rings are valid
before proceeding in bnxt_free_tx_skbs() and
bnxt_free_one_rx_ring_skbs().
Fixes: 975bc99a4a39 ("bnxt_en: Refactor bnxt_free_rx_skbs().") Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sun, 12 Sep 2021 16:34:47 +0000 (12:34 -0400)]
bnxt_en: Fix error recovery regression
The recent patch has introduced a regression by not reading the reset
count in the ERROR_RECOVERY async event handler. We may have just
gone through a reset and the reset count has just incremented. If
we don't update the reset count in the ERROR_RECOVERY event handler,
the health check timer will see that the reset count has changed and
will initiate an unintended reset.
Restore the unconditional update of the reset count in
bnxt_async_event_process() if error recovery watchdog is enabled.
Also, update the reset count at the end of the reset sequence to
make it even more robust.
Fixes: 1b2b91831983 ("bnxt_en: Fix possible unintended driver initiated error recovery") Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Len Baker [Sat, 11 Sep 2021 10:28:18 +0000 (12:28 +0200)]
net: mana: Prefer struct_size over open coded arithmetic
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, use the struct_size() helper to do the arithmetic instead of the
argument "size + count * size" in the kzalloc() function.
Andrea Claudi [Sat, 11 Sep 2021 14:14:18 +0000 (16:14 +0200)]
selftest: net: fix typo in altname test
If altname deletion of the short alternative name fails, the error
message printed is: "Failed to add short alternative name".
This is obviously a typo, as we are testing altname deletion.
Fix this using a proper error message.
Fixes: f95e6c9c4617 ("selftest: net: add alternative names test") Signed-off-by: Andrea Claudi <aclaudi@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith [Sat, 11 Sep 2021 15:50:09 +0000 (17:50 +0200)]
net: dsa: qca8k: fix kernel panic with legacy mdio mapping
When the mdio legacy mapping is used the mii_bus priv registered by DSA
refer to the dsa switch struct instead of the qca8k_priv struct and
causes a kernel panic. Create dedicated function when the internal
dedicated mdio driver is used to properly handle the 2 different
implementation.
Fixes: 759bafb8a322 ("net: dsa: qca8k: add support for internal phy and internal mdio") Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The Synopsys Ethernet IP uses the CSR clock as a base clock for MDC.
The divisor used is set in the MAC_MDIO_Address register field CR
(Clock Rate)
The divisor is there to change the CSR clock into a clock that falls
below the IEEE 802.3 specified max frequency of 2.5MHz.
If the CSR clock is 300MHz, the code falls back to using the reset
value in the MAC_MDIO_Address register, as described in the comment
above this code.
However, 300MHz is actually an allowed value and the proper divider
can be estimated quite easily (it's just 1Hz difference!)
A CSR frequency of 300MHz with the maximum clock rate value of 0x5
(STMMAC_CSR_250_300M, a divisor of 124) gives somewhere around
~2.42MHz which is below the IEEE 802.3 specified maximum.
For the ARTPEC-8 SoC, the CSR clock is this problematic 300MHz,
and unfortunately, the reset-value of the MAC_MDIO_Address CR field
is 0x0.
This leads to a clock rate of zero and a divisor of 42, and gives an
MDC frequency of ~7.14MHz.
Allow CSR clock of 300MHz by making the comparison inclusive.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
and then run the binary at tools/testing/selftests/bpf directory:
./test_progs -t get_stack_raw_tp
The warning is due to commit 5b78ed24e8ec ("mm/pagemap: add mmap_assert_locked()
annotations to find_vma*()") which added mmap_assert_locked() in find_vma()
function. The mmap_assert_locked() function asserts that mm->mmap_lock needs
to be held. But this is not the case for bpf_get_stack() or bpf_get_stackid()
helper (kernel/bpf/stackmap.c), which uses mmap_read_trylock_non_owner()
instead. Since mm->mmap_lock is not held in bpf_get_stack[id]() use case,
the above warning is emitted during test run.
This patch fixed the issue by (1). using mmap_read_trylock() instead of
mmap_read_trylock_non_owner() to satisfy lockdep checking in find_vma(), and
(2). droping lockdep for mmap_lock right before the irq_work_queue(). The
function mmap_read_trylock_non_owner() is also removed since after this
patch nobody calls it any more.
Fixes: 5b78ed24e8ec ("mm/pagemap: add mmap_assert_locked() annotations to find_vma*()") Suggested-by: Jason Gunthorpe <jgg@ziepe.ca> Signed-off-by: Yonghong Song <yhs@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Luigi Rizzo <lrizzo@google.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: linux-mm@kvack.org Link: https://lore.kernel.org/bpf/20210909155000.1610299-1-yhs@fb.com
Handle MFW (management FW) error response in order to avoid a crash
during recovery flows.
Changes from v1:
- Add "Fixes tag".
Fixes: tag 5e7ba042fd05 ("qed: Fix reading stale configuration information") Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: Shai Malin <smalin@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
r6040: Restore MDIO clock frequency after MAC reset
A number of users have reported that they were not able to get the PHY
to successfully link up, especially after commit c36757eb9dee ("net:
phy: consider AN_RESTART status when reading link status") where we
stopped reading just BMSR, but we also read BMCR to determine the link
status.
Andrius at NetBSD did a wonderful job at debugging the problem
and found out that the MDIO bus clock frequency would be incorrectly set
back to its default value which would prevent the MDIO bus controller
from reading PHY registers properly. Back when we only read BMSR, if we
read all 1s, we could falsely indicate a link status, though in general
there is a cable plugged in, so this went unnoticed. After a second read
of BMCR was added, a wrong read will lead to the inability to determine
a link UP condition which is when it started to be visibly broken, even
if it was long before that.
The fix consists in restoring the value of the MD_CSR register that was
set prior to the MAC reset.
Link: http://gnats.netbsd.org/cgi-bin/query-pr-single.pl?number=53494 Fixes: 90f750a81a29 ("r6040: consolidate MAC reset to its own function") Reported-by: Andrius V <vezhlys@gmail.com> Reported-by: Darek Strugacz <darek.strugacz@op.pl> Tested-by: Darek Strugacz <darek.strugacz@op.pl> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Ertman [Thu, 9 Sep 2021 15:12:23 +0000 (08:12 -0700)]
ice: Correctly deal with PFs that do not support RDMA
There are two cases where the current PF does not support RDMA
functionality. The first is if the NVM loaded on the device is set
to not support RDMA (common_caps.rdma is false). The second is if
the kernel bonding driver has included the current PF in an active
link aggregate.
When the driver has determined that this PF does not support RDMA, then
auxiliary devices should not be created on the auxiliary bus. Without
a device on the auxiliary bus, even if the irdma driver is present, there
will be no RDMA activity attempted on this PF.
Currently, in the reset flow, an attempt to create auxiliary devices is
performed without regard to the ability of the PF. There needs to be a
check in ice_aux_plug_dev (as the central point that creates auxiliary
devices) to see if the PF is in a state to support the functionality.
When disabling and re-enabling RDMA due to the inclusion/removal of the PF
in a link aggregate, we also need to set/clear the bit which controls
auxiliary device creation so that a reset recovery in a link aggregate
situation doesn't try to create auxiliary devices when it shouldn't.
Fixes: f9f5301e7e2d ("ice: Register auxiliary device to provide RDMA") Reported-by: Yongxin Liu <yongxin.liu@windriver.com> Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Building alpha:allmodconfig results in the following error.
drivers/net/ethernet/amd/ni65.c: In function 'ni65_stop_start':
drivers/net/ethernet/amd/ni65.c:751:37: error:
cast from pointer to integer of different size
buffer[i] = (u32) isa_bus_to_virt(tmdp->u.buffer);
'buffer[]' is declared as unsigned long, so replace the typecast to u32
with a typecast to unsigned long to fix the problem.
Cc: Arnd Bergmann <arnd@kernel.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 9 Sep 2021 10:17:37 +0000 (11:17 +0100)]
Merge branch 'sfx-xdp-fallback-tx-queues'
Íñigo Huguet says:
====================
sfc: fallback for lack of xdp tx queues
If there are not enough hardware resources to allocate one tx queue per
CPU for XDP, XDP_TX and XDP_REDIRECT actions were unavailable, and using
them resulted each time with the packet being drop and this message in
the logs: XDP TX failed (-22)
These patches implement 2 fallback solutions for 2 different situations
that might happen:
1. There are not enough free resources for all the tx queues, but there
are some free resources available
2. There are not enough free resources at all for tx queues.
Both solutions are based in sharing tx queues, using __netif_tx_lock for
synchronization. In the second case, as there are not XDP TX queues to
share, network stack queues are used instead, but since we're taking
__netif_tx_lock, concurrent access to the queues is correctly protected.
The solution for this second case might affect performance both of XDP
traffic and normal traffice due to lock contention if both are used
intensively. That's why I call it a "last resort" fallback: it's not a
desirable situation, but at least we have XDP TX working.
Some tests has shown good results and indicate that the non-fallback
case is not being damaged by this changes. They are also promising for
the fallback cases. This is the test:
1. From another machine, send high amount of packets with pktgen, script
samples/pktgen/pktgen_sample04_many_flows.sh
2. In the tested machine, run samples/bpf/xdp_rxq_info with arguments
"-a XDP_TX --swapmac" and see the results
3. In the tested machine, run also pktgen_sample04 to create high TX
normal traffic, and see how xdp_rxq_info results vary
Note that this test doesn't check the worst situations for the fallback
solutions because XDP_TX will only be executed from the same CPUs that
are processed by sfc, and not from every CPU in the system, so the
performance drop due to the highest locking contention doesn't happen.
I'd like to test that, as well, but I don't have access right now to a
proper environment.
Test results:
Without doing TX:
Before changes: ~2,900,000 pps
After changes, 1 queues/core: ~2,900,000 pps
After changes, 2 queues/core: ~2,900,000 pps
After changes, 8 queues/core: ~2,900,000 pps
After changes, borrowing from network stack: ~2,900,000 pps
With multiflow TX at the same time:
Before changes: ~1,700,000 - 2,900,000 pps
After changes, 1 queues/core: ~1,700,000 - 2,900,000 pps
After changes, 2 queues/core: ~1,700,000 pps
After changes, 8 queues/core: ~1,700,000 pps
After changes, borrowing from network stack: 1,150,000 pps
Sporadic "XDP TX failed (-5)" warnings are shown when running xdp program
and pktgen simultaneously. This was expected because XDP doesn't have any
buffering system if the NIC is under very high pressure. Thousands of
these warnings are shown in the case of borrowing net stack queues. As I
said before, this was also expected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
sfc: last resort fallback for lack of xdp tx queues
Previous patch addressed the situation of having some free resources for
xdp tx but not enough for one tx queue per CPU. This patch address the
worst case of not having resources at all for xdp tx.
Instead of using queues dedicated to xdp, normal queues used by network
stack are shared for both cases, using __netif_tx_lock for
synchronization. Also queue stop/restart must be considered in the xdp
path to avoid freezing the queue.
This is not the ideal situation we might want to be, and a performance
penalty is expected both for normal and xdp traffic, but at least XDP
will work in all possible situations (with a warning in the logs),
improving a bit the pain of not knowing in what situations we can use it
and in what situations we cannot.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If there are not enough resources to allocate one TX queue per core for
XDP TX it was completely disabled.
This patch implements a fallback solution for sharing the available
queues using __netif_tx_lock for synchronization. In the normal case that
there is one TX queue per CPU, no locking is done, as it was before.
With this fallback solution, XDP TX will work in much more cases that
were failing, specially in machines with many CPUs. It's hard for XDP
users to know what features are supported across different NICs and
configurations, so they will benefit on having wider support.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: stmmac: platform: fix build warning when with !CONFIG_PM_SLEEP
Use __maybe_unused for noirq_suspend()/noirq_resume() hooks to avoid
build warning with !CONFIG_PM_SLEEP:
>> drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:796:12: error: 'stmmac_pltfr_noirq_resume' defined but not used [-Werror=unused-function]
796 | static int stmmac_pltfr_noirq_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
>> drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:775:12: error: 'stmmac_pltfr_noirq_suspend' defined but not used [-Werror=unused-function]
775 | static int stmmac_pltfr_noirq_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Fixes: 276aae377206 ("net: stmmac: fix system hang caused by eee_ctrl_timer during suspend/resume") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xiyu Yang [Thu, 9 Sep 2021 04:32:00 +0000 (12:32 +0800)]
net/l2tp: Fix reference count leak in l2tp_udp_recv_core
The reference count leak issue may take place in an error handling
path. If both conditions of tunnel->version == L2TP_HDR_VER_3 and the
return value of l2tp_v3_ensure_opt_in_linear is nonzero, the function
would directly jump to label invalid, without decrementing the reference
count of the l2tp_session object session increased earlier by
l2tp_tunnel_get_session(). This may result in refcount leaks.
Fix this issue by decrease the reference count before jumping to the
label invalid.
Fixes: 4522a70db7aa ("l2tp: fix reading optional fields of L2TPv3") Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
read to 0xffff88814eeb24e0 of 4 bytes by task 25834 on cpu 1:
skb_queue_len include/linux/skbuff.h:1869 [inline]
unix_recvq_full net/unix/af_unix.c:194 [inline]
unix_dgram_poll+0x2bc/0x3e0 net/unix/af_unix.c:2777
sock_poll+0x23e/0x260 net/socket.c:1288
vfs_poll include/linux/poll.h:90 [inline]
ep_item_poll fs/eventpoll.c:846 [inline]
ep_send_events fs/eventpoll.c:1683 [inline]
ep_poll fs/eventpoll.c:1798 [inline]
do_epoll_wait+0x6ad/0xf00 fs/eventpoll.c:2226
__do_sys_epoll_wait fs/eventpoll.c:2238 [inline]
__se_sys_epoll_wait fs/eventpoll.c:2233 [inline]
__x64_sys_epoll_wait+0xf6/0x120 fs/eventpoll.c:2233
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x0000001b -> 0x00000001
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 25834 Comm: syz-executor.1 Tainted: G W 5.14.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 86b18aaa2b5b ("skbuff: fix a data race in skb_queue_len()") Cc: Qian Cai <cai@lca.pw> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
plat_dev->dev->platform_data is released by platform_device_unregister(),
use of pclk and hclk is a use-after-free. Since device unregister won't
need a clk device we adjust the function call sequence to fix this issue.
[ 31.261225] BUG: KASAN: use-after-free in macb_remove+0x77/0xc6 [macb_pci]
[ 31.275563] Freed by task 306:
[ 30.276782] platform_device_release+0x25/0x80
Suggested-by: Nicolas Ferre <Nicolas.Ferre@microchip.com> Signed-off-by: Tong Zhang <ztong0001@gmail.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If a failover occurs before a login response is received, the login
response buffer maybe undefined. Check that there was no failover
before accessing the login response buffer.
Fixes: 032c5e82847a ("Driver for IBM System i/p VNIC protocol") Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 8 Sep 2021 11:42:09 +0000 (13:42 +0200)]
vhost_net: fix OoB on sendmsg() failure.
If the sendmsg() call in vhost_tx_batch() fails, both the 'batched_xdp'
and 'done_idx' indexes are left unchanged. If such failure happens
when batched_xdp == VHOST_NET_BATCH, the next call to
vhost_net_build_xdp() will access and write memory outside the xdp
buffers area.
Since sendmsg() can only error with EBADFD, this change addresses the
issue explicitly freeing the XDP buffers batch on error.
Fixes: 0a0be13b8fe2 ("vhost_net: batch submitting XDP buffers to underlayer sockets") Suggested-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: stmmac: fix system hang caused by eee_ctrl_timer during suspend/resume
commit 5f58591323bf ("net: stmmac: delete the eee_ctrl_timer after
napi disabled"), this patch tries to fix system hang caused by eee_ctrl_timer,
unfortunately, it only can resolve it for system reboot stress test. System
hang also can be reproduced easily during system suspend/resume stess test
when mount NFS on i.MX8MP EVK board.
In stmmac driver, eee feature is combined to phylink framework. When do
system suspend, phylink_stop() would queue delayed work, it invokes
stmmac_mac_link_down(), where to deactivate eee_ctrl_timer synchronizly.
In above commit, try to fix issue by deactivating eee_ctrl_timer obviously,
but it is not enough. Looking into eee_ctrl_timer expire callback
stmmac_eee_ctrl_timer(), it could enable hareware eee mode again. What is
unexpected is that LPI interrupt (MAC_Interrupt_Enable.LPIEN bit) is always
asserted. This interrupt has chance to be issued when LPI state entry/exit
from the MAC, and at that time, clock could have been already disabled.
The result is that system hang when driver try to touch register from
interrupt handler.
The reason why above commit can fix system hang issue in stmmac_release()
is that, deactivate eee_ctrl_timer not just after napi disabled, further
after irq freed.
In conclusion, hardware would generate LPI interrupt when clock has been
disabled during suspend or resume, since hardware is in eee mode and LPI
interrupt enabled.
Interrupts from MAC, MTL and DMA level are enabled and never been disabled
when system suspend, so postpone clocks management from suspend stage to
noirq suspend stage should be more safe.
Fixes: 5f58591323bf ("net: stmmac: delete the eee_ctrl_timer after napi disabled") Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Tue, 7 Sep 2021 17:05:54 +0000 (12:05 -0500)]
net: ipa: initialize all filter table slots
There is an off-by-one problem in ipa_table_init_add(), when
initializing filter tables.
In that function, the number of filter table entries is determined
based on the number of set bits in the filter map. However that
count does *not* include the extra "slot" in the filter table that
holds the filter map itself. Meanwhile, ipa_table_addr() *does*
include the filter map in the memory it returns, but because the
count it's provided doesn't include it, it includes one too few
table entries.
Fix this by including the extra slot for the filter map in the count
computed in ipa_table_init_add().
Note: ipa_filter_reset_table() does not have this problem; it resets
filter table entries one by one, but does not overwrite the filter
bitmap.
Fixes: 2b9feef2b6c2 ("soc: qcom: ipa: filter and routing tables") Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phylink: Update SFP selected interface on advertising changes
Currently changes to the advertising state via ethtool do not cause any
reselection of the configured interface mode after the SFP is already
inserted and initially configured.
While it is not typical to change the advertised link modes for an
interface using an SFP in certain use cases it is desirable. In the case
of a SFP port that is capable of handling both SFP and SFP+ modules it
will automatically select between 1G and 10G modes depending on the
supported mode of the SFP. However if the SFP module is capable of
working in multiple modes (e.g. a SFP+ DAC that can operate at 1G or
10G), one end of the cable may be attached to a SFP 1000base-x port thus
the SFP+ end must be manually configured to the 1000base-x mode in order
for the link to be established.
This change causes the ethtool setting of advertised mode changes to
reselect the interface mode so that the link can be established.
Additionally when a module is inserted the advertising mode is reset to
match the supported modes of the module.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 8 Sep 2021 10:40:03 +0000 (11:40 +0100)]
Merge tag 'mlx5-fixes-2021-09-07' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2021-09-07
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
Included here, a patch which solves a build warning reported on
linux-kernel mailing list [1]:
Fix commit ("net/mlx5: Bridge, fix uninitialized variable usage")
If a failover occurs before a login response is received, the login
response buffer maybe undefined. Check that there was no failover
before accessing the login response buffer.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
- we're missing the rcu read lock acquire around the destruction path.
This change adds the acquire/release - the path is already atomic, and
we're using the _rcu list iterators.
Reported-by: kernel test robot <oliver.sang@intel.com> Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2677d2067731 ("dccp: don't free ccid2_hc_tx_sock ...") fixed
a UAF but reintroduced CVE-2017-6074.
When the sock is cloned, two dccps_hc_tx_ccid will reference to the
same ccid. So one can free the ccid object twice from two socks after
cloning.
This issue was found by "Hadar Manor" as well and assigned with
CVE-2020-16119, which was fixed in Ubuntu's kernel. So here I port
the patch from Ubuntu to fix it.
The patch prevents cloned socks from referencing the same ccid.
Fixes: 2677d2067731410 ("dccp: don't free ccid2_hc_tx_sock ...") Signed-off-by: Zhenpeng Lin <zplin@psu.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
Aya Levin [Sun, 29 Aug 2021 10:41:08 +0000 (13:41 +0300)]
net/mlx5e: Fix condition when retrieving PTP-rqn
When activating the PTP-RQ, redirect the RQT from drop-RQ to PTP-RQ.
Use mlx5e_channels_get_ptp_rqn to retrieve the rqn. This helper returns
a boolean (not status), hence caller should consider return value 0 as a
fail. Change the caller interpretation of the return value.
Fixes: 43ec0f41fa73 ("net/mlx5e: Hide all implementation details of mlx5e_rx_res") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Aya Levin [Thu, 15 Jul 2021 07:53:28 +0000 (10:53 +0300)]
net/mlx5e: Fix mutual exclusion between CQE compression and HW TS
Some profiles of the driver don't support a dedicated PTP-RQ, hence can't
support HW TS and CQE compression simultaneously. When HW TS is enabled
the COE compression is disabled, and should be restored when the HW TS
is turned off. Add rx_filter as an input to modifying CQE compression to
enforce this restriction.
Fixes: 256f79d13c1d ("net/mlx5e: Fix HW TS with CQE compression according to profile") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Fixes: 693c6883bbc4 ("net/mlx5: Add hash table for flow groups in flow table") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Maor Gottlieb <maorg@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Parav Pandit [Tue, 17 Aug 2021 12:59:17 +0000 (15:59 +0300)]
net/mlx5: Fix rdma aux device on devlink reload
RDMA auxdev parameter registration was skipped for eswitch manager PCI PF.
Due to this when devlink parameter is read, it reads as false in below
code flow.
$ devlink dev reload pci/0000:06:00.0
devlink_reload()
mlx5_load_one()
mlx5_attach_device()
is_ib_enabled()
devlink_param_driverinit_value_get()
Due to this, is_ib_enabled() returns false for the RDMA auxiliary
device. This results into a skipping RDMA auxiliary device creation on
reload.
There is no need to check for eswitch manager capability to support RDMA
auxiliary device. Hence, fix it by skipping eswitch manager capability.
Fixes: 87158cedf00e ("net/mlx5: Support enable_rdma devlink dev param") Signed-off-by: Parav Pandit <parav@nvidia.com> Reviewed-by: Shay Drory <shayd@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In some conditions variable 'err' is not assigned with value in
mlx5_esw_bridge_port_obj_attr_set() and mlx5_esw_bridge_port_changeupper()
functions after recent changes to support LAG. Initialize the variable with
zero value in both cases.
Reported-by: Colin King <colin.king@canonical.com> Reported-by: Tim Gardner <tim.gardner@canonical.com> Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org> CC: linux-kernel@vger.kernel.org Fixes: ff9b7521468b ("net/mlx5: Bridge, support LAG") Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
- netfilter: refuse insertion if chain has grown too large
- ncsi: add get MAC address command to get Intel i210 MAC address"
* tag 'net-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (76 commits)
ieee802154: Remove redundant initialization of variable ret
net: stmmac: fix MAC not working when system resume back with WoL active
net: phylink: add suspend/resume support
net: renesas: sh_eth: Fix freeing wrong tx descriptor
bonding: 3ad: pass parameter bond_params by reference
cxgb3: fix oops on module removal
can: c_can: fix null-ptr-deref on ioctl()
can: rcar_canfd: add __maybe_unused annotation to silence warning
net: wwan: iosm: Unify IO accessors used in the driver
net: wwan: iosm: Replace io.*64_lo_hi() with regular accessors
net: qcom/emac: Replace strlcpy with strscpy
ip6_gre: Revert "ip6_gre: add validation for csum_start"
net: hns3: make hclgevf_cmd_caps_bit_map0 and hclge_cmd_caps_bit_map0 static
selftests/bpf: Test XDP bonding nest and unwind
bonding: Fix negative jump label count on nested bonding
MAINTAINERS: add VM SOCKETS (AF_VSOCK) entry
stmmac: dwmac-loongson:Fix missing return value
iwlwifi: fix printk format warnings in uefi.c
net: create netdev->dev_addr assignment helpers
bnxt_en: Fix possible unintended driver initiated error recovery
...
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- Page ownership tracking between host EL1 and EL2
- Rely on userspace page tables to create large stage-2 mappings
- Fix incompatibility between pKVM and kmemleak
- Fix the PMU reset state, and improve the performance of the virtual
PMU
- Move over to the generic KVM entry code
- Address PSCI reset issues w.r.t. save/restore
- Preliminary rework for the upcoming pKVM fixed feature
- A bunch of MM cleanups
- a vGIC fix for timer spurious interrupts
- Various cleanups
s390:
- enable interpretation of specification exceptions
- fix a vcpu_idx vs vcpu_id mixup
x86:
- fast (lockless) page fault support for the new MMU
- new MMU now the default
- increased maximum allowed VCPU count
- allow inhibit IRQs on KVM_RUN while debugging guests
- let Hyper-V-enabled guests run with virtualized LAPIC as long as
they do not enable the Hyper-V "AutoEOI" feature
- fixes and optimizations for the toggling of AMD AVIC (virtualized
LAPIC)
- tuning for the case when two-dimensional paging (EPT/NPT) is
disabled
- bugfixes and cleanups, especially with respect to vCPU reset and
choosing a paging mode based on CR0/CR4/EFER
- support for 5-level page table on AMD processors
Generic:
- MMU notifier invalidation callbacks do not take mmu_lock unless
necessary
- improved caching of LRU kvm_memory_slot
- support for histogram statistics
- add statistics for halt polling and remote TLB flush requests"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (210 commits)
KVM: Drop unused kvm_dirty_gfn_invalid()
KVM: x86: Update vCPU's hv_clock before back to guest when tsc_offset is adjusted
KVM: MMU: mark role_regs and role accessors as maybe unused
KVM: MIPS: Remove a "set but not used" variable
x86/kvm: Don't enable IRQ when IRQ enabled in kvm_wait
KVM: stats: Add VM stat for remote tlb flush requests
KVM: Remove unnecessary export of kvm_{inc,dec}_notifier_count()
KVM: x86/mmu: Move lpage_disallowed_link further "down" in kvm_mmu_page
KVM: x86/mmu: Relocate kvm_mmu_page.tdp_mmu_page for better cache locality
Revert "KVM: x86: mmu: Add guest physical address check in translate_gpa()"
KVM: x86/mmu: Remove unused field mmio_cached in struct kvm_mmu_page
kvm: x86: Increase KVM_SOFT_MAX_VCPUS to 710
kvm: x86: Increase MAX_VCPUS to 1024
kvm: x86: Set KVM_MAX_VCPU_ID to 4*KVM_MAX_VCPUS
KVM: VMX: avoid running vmx_handle_exit_irqoff in case of emulation
KVM: x86/mmu: Don't freak out if pml5_root is NULL on 4-level host
KVM: s390: index kvm->arch.idle_mask by vcpu_idx
KVM: s390: Enable specification exception interpretation
KVM: arm64: Trim guest debug exception handling
KVM: SVM: Add 5-level page table support for SVM
...
Merge tag 'ntb-5.15' of git://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"Bug fixes and clean-ups for Linux v5.15"
* tag 'ntb-5.15' of git://github.com/jonmason/ntb:
NTB: switch from 'pci_' to 'dma_' API
ntb: ntb_pingpong: remove redundant initialization of variables msg_data and spad_data
NTB: perf: Fix an error code in perf_setup_inbuf()
NTB: Fix an error code in ntb_msit_probe()
ntb: intel: remove invalid email address in header comment
Merge tag 'backlight-next-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"Fix-ups:
- Improve bootloader/kernel device handover
Bug Fixes:
- Stabilise backlight in ktd253 driver"
* tag 'backlight-next-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: pwm_bl: Improve bootloader/kernel device handover
backlight: ktd253: Stabilize backlight
Merge tag 'mfd-next-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Add support for registering devices via MFD cells to Simple MFD (I2C)
New Drivers:
- Add support for Renesas Synchronization Management Unit (SMU)
New Device Support:
- Add support for N5010 to Intel M10 BMC
- Add support for Cannon Lake to Intel LPSS ACPI
- Add support for Samsung SSG{1,2} to ST-Ericsson's U8500 family
- Add support for TQMx110EB and TQMxE40x to TQ-Systems PLD TQMx86
New Functionality:
- Add support for GPIO to Intel LPC ICH
- Add support for Reset to Texas Instruments TPS65086
Fix-ups:
- Trivial, sorting, whitespace, renaming, etc; mt6360-core, db8500-prcmu-regs, tqmx86
- Device Tree fiddling; syscon, axp20x, qcom,pm8008, ti,tps65086, brcm,cru
- Use proper APIs for IRQ map resolution; ab8500-core, stmpe, tc3589x, wm8994-irq
- Pass 'supplied-from' property through axp288_fuel_gauge via swnode
- Remove unused file entry; MAINTAINERS
- Make interrupt line optional; tps65086
- Rename db8500-cpuidle driver symbol; db8500-prcmu
- Remove support for unused hardware; tqmx86
- Provide a standard LPC clock frequency for unknown boards; tqmx86
- Remove unused code; ti_am335x_tscadc
- Use of_iomap() instead of ioremap(); syscon
Bug Fixes:
- Clear GPIO IRQ resource flags when no IRQ is set; tqmx86
- Fix incorrect/misleading frequencies; db8500-prcmu
- Mitigate namespace clash with other GPIOBASE users"
* tag 'mfd-next-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (31 commits)
mfd: lpc_sch: Rename GPIOBASE to prevent build error
mfd: syscon: Use of_iomap() instead of ioremap()
dt-bindings: mfd: Add Broadcom CRU
mfd: ti_am335x_tscadc: Delete superfluous error message
mfd: tqmx86: Assume 24MHz LPC clock for unknown boards
mfd: tqmx86: Add support for TQ-Systems DMI IDs
mfd: tqmx86: Add support for TQMx110EB and TQMxE40x
mfd: tqmx86: Fix typo in "platform"
mfd: tqmx86: Remove incorrect TQMx90UC board ID
mfd: tqmx86: Clear GPIO IRQ resource when no IRQ is set
mfd: simple-mfd-i2c: Add support for registering devices via MFD cells
mfd/cpuidle: ux500: Rename driver symbol
mfd: tps65086: Add cell entry for reset driver
mfd: tps65086: Make interrupt line optional
dt-bindings: mfd: Convert tps65086.txt to YAML
MAINTAINERS: Adjust ARM/NOMADIK/Ux500 ARCHITECTURES to file renaming
mfd: db8500-prcmu: Handle missing FW variant
mfd: db8500-prcmu: Rename register header
mfd: axp20x: Add supplied-from property to axp288_fuel_gauge cell
mfd: Don't use irq_create_mapping() to resolve a mapping
...
Merge tag 'gpio-updates-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We mostly have various improvements and refactoring all over the place
but also some interesting new features - like the virtio GPIO driver
that allows guest VMs to use host's GPIOs. We also have a new/old GPIO
driver for rockchip - this one has been split out of the pinctrl
driver.
Summary:
- new driver: gpio-virtio allowing a guest VM running linux to access
GPIO lines provided by the host
- split the GPIO driver out of the rockchip pin control driver
- add support for a new model to gpio-aspeed-sgpio, refactor the
driver and use generic device property interfaces, improve property
sanitization
- add ACPI support to gpio-tegra186
- improve the code setting the line names to support multiple GPIO
banks per device
- constify a bunch of OF functions in the core GPIO code and make the
declaration for one of the core OF functions we use consistent
within its header
- use software nodes in intel_quark_i2c_gpio
- add support for the gpio-line-names property in gpio-mt7621
- use the standard GPIO function for setting the GPIO names in
gpio-brcmstb
- fix a bunch of leaks and other bugs in gpio-mpc8xxx
- use generic pm callbacks in gpio-ml-ioh
- improve resource management and PM handling in gpio-mlxbf2
- modernize and improve the gpio-dwapb driver
- coding style improvements in gpio-rcar
- documentation fixes and improvements
- update the MAINTAINERS entry for gpio-zynq
- minor tweaks in several drivers"
* tag 'gpio-updates-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (35 commits)
gpio: mpc8xxx: Use 'devm_gpiochip_add_data()' to simplify the code and avoid a leak
gpio: mpc8xxx: Fix a potential double iounmap call in 'mpc8xxx_probe()'
gpio: mpc8xxx: Fix a resources leak in the error handling path of 'mpc8xxx_probe()'
gpio: viperboard: remove platform_set_drvdata() call in probe
gpio: virtio: Add missing mailings lists in MAINTAINERS entry
gpio: virtio: Fix sparse warnings
gpio: remove the obsolete MX35 3DS BOARD MC9S08DZ60 GPIO functions
gpio: max730x: Use the right include
gpio: Add virtio-gpio driver
gpio: mlxbf2: Use DEFINE_RES_MEM_NAMED() helper macro
gpio: mlxbf2: Use devm_platform_ioremap_resource()
gpio: mlxbf2: Drop wrong use of ACPI_PTR()
gpio: mlxbf2: Convert to device PM ops
gpio: dwapb: Get rid of legacy platform data
mfd: intel_quark_i2c_gpio: Convert GPIO to use software nodes
gpio: dwapb: Read GPIO base from gpio-base property
gpio: dwapb: Unify ACPI enumeration checks in get_irq() and configure_irqs()
gpiolib: Deduplicate forward declaration in the consumer.h header
MAINTAINERS: update gpio-zynq.yaml reference
gpio: tegra186: Add ACPI support
...
Merge tag 'fuse-update-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse updates from Miklos Szeredi:
- Allow mounting an active fuse device. Previously the fuse device
would always be mounted during initialization, and sharing a fuse
superblock was only possible through mount or namespace cloning
- Fix data flushing in syncfs (virtiofs only)
- Fix data flushing in copy_file_range()
- Fix a possible deadlock in atomic O_TRUNC
- Misc fixes and cleanups
* tag 'fuse-update-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: remove unused arg in fuse_write_file_get()
fuse: wait for writepages in syncfs
fuse: flush extending writes
fuse: truncate pagecache on atomic_o_trunc
fuse: allow sharing existing sb
fuse: move fget() to fuse_get_tree()
fuse: move option checking into fuse_fill_super()
fuse: name fs_context consistently
fuse: fix use after free in fuse_read_interrupt()
Merge tag 'kgdb-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux
Pull kgdb updates from Daniel Thompson:
"Changes for kgdb/kdb this cycle are dominated by a change from Sumit
that removes as small (256K) private heap from kdb. This is change
I've hoped for ever since I discovered how few users of this heap
remained in the kernel, so many thanks to Sumit for hunting these
down.
The other change is an incremental step towards SPDX headers"
* tag 'kgdb-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux:
kernel: debug: Convert to SPDX identifier
kdb: Rename members of struct kdbtab_t
kdb: Simplify kdb_defcmd macro logic
kdb: Get rid of redundant kdb_register_flags()
kdb: Rename struct defcmd_set to struct kdb_macro
kdb: Get rid of custom debug heap allocator
Just like with the memcg lock accounting, the kernel test robot reports
a sizeable performance regression for this commit, and while it clearly
does the rigth thing in theory, we'll need to look at just how to avoid
or minimize the performance overhead of the memcg accounting.
People already have suggestions on how to do that, but it's "future
work".
So revert it for now.
[ Note: the first link below is for this same commit but a different
commit ID, because it's the kernel test robot ended up noticing it in
Andrew Morton's patch queue ]
The kernel test robot reports a sizeable performance regression for this
commit, and while it clearly does the rigth thing in theory, we'll need
to look at just how to avoid or minimize the performance overhead of the
memcg accounting.
People already have suggestions on how to do that, but it's "future
work".
That commit was completely broken, and I should have caught on to it
earlier. But happily, the kernel test robot noticed the breakage fairly
quickly.
The breakage is because "try_get_page()" is about avoiding the page
reference count overflow case, but is otherwise the exact same as a
plain "get_page()".
In contrast, "try_get_compound_head()" is an entirely different beast,
and uses __page_cache_add_speculative() because it's not just about the
page reference count, but also about possibly racing with the underlying
page going away.
So all the commentary about how
"try_get_page() has fallen a little behind in terms of maintenance,
try_get_compound_head() handles speculative page references more
thoroughly"
was just completely wrong: yes, try_get_compound_head() handles
speculative page references, but the point is that try_get_page() does
not, and must not.
So there's no lack of maintainance - there are fundamentally different
semantics.
A speculative page reference would be entirely wrong in "get_page()",
and it's entirely wrong in "try_get_page()". It's not about
speculation, it's purely about "uhhuh, you can't get this page because
you've tried to increment the reference count too much already".
The reason the kernel test robot noticed this bug was that it hit the
VM_BUG_ON() in __page_cache_add_speculative(), which is all about
verifying that the context of any speculative page access is correct.
But since that isn't what try_get_page() is all about, the VM_BUG_ON()
tests things that are not correct to test for try_get_page().
Reported-by: kernel test robot <oliver.sang@intel.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
selftests/bpf: Fix build of task_pt_regs test for arm64
struct pt_regs is not exported to userspace on all archs. arm64 and s390
export "user_pt_regs" instead, which causes build failure at the moment:
progs/test_task_pt_regs.c:8:16: error: variable has incomplete type 'struct pt_regs'
struct pt_regs current_regs = {};
Instead of using pt_regs from ptrace.h, use the larger kernel struct
from vmlinux.h directly. Since the test runner task_pt_regs.c does not
have access to the kernel struct definition, copy it into a char array.
David S. Miller [Tue, 7 Sep 2021 13:04:59 +0000 (14:04 +0100)]
Merge branch 'stmmac-wol-fix'
Joakim Zhang says:
====================
net: stmmac: fix WoL issue
This patch set fixes stmmac not working after system resume back with WoL
active. Thanks a lot for Russell King keeps looking into this issue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: stmmac: fix MAC not working when system resume back with WoL active
We can reproduce this issue with below steps:
1) enable WoL on the host
2) host system suspended
3) remote client send out wakeup packets
We can see that host system resume back, but can't work, such as ping failed.
After a bit digging, this issue is introduced by the commit 46f69ded988d
("net: stmmac: Use resolved link config in mac_link_up()"), which use
the finalised link parameters in mac_link_up() rather than the
parameters in mac_config().
There are two scenarios for MAC suspend/resume in STMMAC driver:
1) MAC suspend with WoL inactive, stmmac_suspend() call
phylink_mac_change() to notify phylink machine that a change in MAC
state, then .mac_link_down callback would be invoked. Further, it will
call phylink_stop() to stop the phylink instance. When MAC resume back,
firstly phylink_start() is called to start the phylink instance, then
call phylink_mac_change() which will finally trigger phylink machine to
invoke .mac_config and .mac_link_up callback. All is fine since
configuration in these two callbacks will be initialized, that means MAC
can restore the state.
2) MAC suspend with WoL active, phylink_mac_change() will put link
down, but there is no phylink_stop() to stop the phylink instance, so it
will link up again, that means .mac_config and .mac_link_up would be
invoked before system suspended. After system resume back, it will do
DMA initialization and SW reset which let MAC lost the hardware setting
(i.e MAC_Configuration register(offset 0x0) is reset). Since link is up
before system suspended, so .mac_link_up would not be invoked after
system resume back, lead to there is no chance to initialize the
configuration in .mac_link_up callback, as a result, MAC can't work any
longer.
After discussed with Russell King [1], we confirm that phylink framework
have not take WoL into consideration yet. This patch calls
phylink_suspend()/phylink_resume() functions which is newly introduced
by Russell King to fix this issue.
Fixes: 46f69ded988d ("net: stmmac: Use resolved link config in mac_link_up()") Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joakim Zhang reports that Wake-on-Lan with the stmmac ethernet driver broke
when moving the incorrect handling of mac link state out of mac_config().
This reason this breaks is because the stmmac's WoL is handled by the MAC
rather than the PHY, and phylink doesn't cater for that scenario.
This patch adds the necessary phylink code to handle suspend/resume events
according to whether the MAC still needs a valid link or not. This is the
barest minimum for this support.
Reported-by: Joakim Zhang <qiangqing.zhang@nxp.com> Tested-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The cur_tx counter must be incremented after TACT bit of
txdesc->status was set. However, a CPU is possible to reorder
instructions and/or memory accesses between cur_tx and
txdesc->status. And then, if TX interrupt happened at such a
timing, the sh_eth_tx_free() may free the descriptor wrongly.
So, add wmb() before cur_tx++.
Otherwise NETDEV WATCHDOG timeout is possible to happen.
Fixes: 86a74ff21a7a ("net: sh_eth: add support for Renesas SuperH Ethernet") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 7 Sep 2021 08:45:34 +0000 (09:45 +0100)]
bonding: 3ad: pass parameter bond_params by reference
The parameter bond_params is a relatively large 192 byte sized
struct so pass it by reference rather than by value to reduce
copying.
Addresses-Coverity: ("Big parameter passed by value") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 7 Sep 2021 09:04:47 +0000 (10:04 +0100)]
Merge tag 'wireless-drivers-2021-09-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.15
First set of fixes for v5.15 and only iwlwifi patches this time. Most
important being support for new hardware and new firmware API.
I had already earlier applied a fix which also Linus applied to this
tree as commit 1476ff21abb4 ("iwl: fix debug printf format strings"),
but this doesn't seem to cause any conflicts so I left it there.
iwlwifi
* add support for firmware API 66
* add support for Samsung Galaxy Book Flex2 Alpha
* fix a leak happening every time module is loaded
* fix a printk compiler warning
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing the driver module w/o bringing an interface up before
the error below occurs. Reason seems to be that cancel_work_sync() is
called in t3_sge_stop() for a queue that hasn't been initialized yet.
Fixes: 5e0b8928927f ("net:cxgb3: replace tasklets with works") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Randy Dunlap [Tue, 7 Sep 2021 00:19:49 +0000 (17:19 -0700)]
mfd: lpc_sch: Rename GPIOBASE to prevent build error
One MIPS platform (mach-rc32434) defines GPIOBASE. This macro
conflicts with one of the same name in lpc_sch.c. Rename the latter one
to prevent the build error.
../drivers/mfd/lpc_sch.c:25: error: "GPIOBASE" redefined [-Werror]
25 | #define GPIOBASE 0x44
../arch/mips/include/asm/mach-rc32434/rb.h:32: note: this is the location of the previous definition
32 | #define GPIOBASE 0x050000
Cc: Denis Turischev <denis@compulab.co.il> Fixes: e82c60ae7d3a ("mfd: Introduce lpc_sch for Intel SCH LPC bridge") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
The pdev maybe not a platform device, e.g. c_can_pci device, in this
case, calling to_platform_device() would not make sense. Also, per the
comment in drivers/net/can/c_can/c_can_ethtool.c, @bus_info should
match dev_name() string, so I am replacing this with dev_name() to fix
this issue.
can: rcar_canfd: add __maybe_unused annotation to silence warning
Since commit
| dd3bd23eb438 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver")
the rcar_canfd driver can be compile tested on all architectures. On
non OF enabled archs, or archs where OF is optional (and disabled in
the .config) the compilation throws the following warning:
thunderbolt: test: split up test cases in tb_test_credit_alloc_all
The tb_test_credit_alloc_all() function had a huge number of
KUNIT_ASSERT() statements, all of which (though the magic of many many
layers of inscrutable macros) ended up allocating and initializing
various test assertion structures on the stack.
Don't do that. The kernel stack isn't infinite, and we have compiler
warnings (now errors) for the case where a stack frame grows too large.
Like it did here, by not an inconsiderable margin:
drivers/thunderbolt/test.c: In function ‘tb_test_credit_alloc_all’:
drivers/thunderbolt/test.c:2367:1: error: the frame size of 4500 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
2367 | }
| ^
Solve this similarly to the lib/test_scanf case: split out the tests
into several smaller functions, each just testing one particular tunnel
credit allocation.
This makes the i386 allyesconfig build work for me again.
lib/test_scanf: split up number parsing test routines
It turns out that gcc has real trouble merging all the temporary
on-stack buffer allocation. So despite the fact that their lifetimes do
not overlap, gcc will allocate stack for all of them when they have
different types. Which they do in the number scanning test routines.
This is unfortunate in general, but with lots of test-cases in one
function, it becomes a real problem. gcc will allocate a huge stack
frame for no actual good reason.
We have tried to counteract this tendency of gcc not merging stack slots
(see "-fconserve-stack"), but that has limited effect (and should be on
by default these days, iirc).
So with all the debug options enabled on an i386 allmodconfig build, we
end up with overly big stack frames, and the resulting stack frame size
warnings (now errors):
lib/test_scanf.c: In function ‘numbers_list_field_width_val_width’:
lib/test_scanf.c:530:1: error: the frame size of 2088 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
530 | }
| ^
lib/test_scanf.c: In function ‘numbers_list_field_width_typemax’:
lib/test_scanf.c:488:1: error: the frame size of 2568 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
488 | }
| ^
lib/test_scanf.c: In function ‘numbers_list’:
lib/test_scanf.c:437:1: error: the frame size of 2088 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
437 | }
| ^
In this particular case, the reasonably straightforward solution is to
just split out the test routines into multiple more targeted versions.
That way we don't have one huge stack, but several smaller ones, and
they aren't active all at the same time.
The variable 'package_size' is an unsigned long, and should be printed
out using '%lu', not '%zd' (that would be for a size_t).
Yes, on many architectures (including x86-64), 'size_t' is in fact the
same type as 'long', but that's a fairly random architecture definition,
and on some platforms 'size_t' is in fact 'int' rather than 'long'.
That is the case on traditional 32-bit x86. Yes, both types are the
exact same 32-bit size, and it would all print out perfectly correctly,
but '%zd' ends up still being wrong.
And we can't make 'package_size' be a 'size_t', because we get the
actual value using efivar_entry_get() that takes a pointer to an
'unsigned long'. So '%lu' it is.
This fixes two of the i386 allmodconfig build warnings (that is now an
error due to -Werror).
Merge tag 'block-5.15-2021-09-05' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Was going to send this one in later this week, but given that -Werror
is now enabled (or at least available), the mq-deadline fix really
should go in for the folks hitting that.
- Ensure dd_queued() is only there if needed (Geert)
- Fix a kerneldoc warning for bio_alloc_kiocb()
- BFQ fix for queue merging
- loop locking fix (Tetsuo)"
* tag 'block-5.15-2021-09-05' of git://git.kernel.dk/linux-block:
loop: reduce the loop_ctl_mutex scope
bio: fix kerneldoc documentation for bio_alloc_kiocb()
block, bfq: honor already-setup queue merges
block/mq-deadline: Move dd_queued() to fix defined but not used warning
Merge tag 'misc-5.15-2021-09-05' of git://git.kernel.dk/linux-block
Pull CDROM maintainer update from Jens Axboe:
"It's been about 22 years since I originally started maintaining the
CDROM code, and I just haven't been able to even get reviews done in a
timely fashion the last handful of years.
Time to pass it on, and Phillip has volunteered take over these
duties. I'll be helping as needed for the foreseeable future"
* tag 'misc-5.15-2021-09-05' of git://git.kernel.dk/linux-block:
cdrom: update uniform CD-ROM maintainership in MAINTAINERS file
Merge tag 'libata-5.15-2021-09-05' of git://git.kernel.dk/linux-block
Pull libata fixes from Jens Axboe:
"Fixes for queued trim on certain Samsung SSDs, in conjunction with
certain ATI controllers"
* tag 'libata-5.15-2021-09-05' of git://git.kernel.dk/linux-block:
libata: Add ATA_HORKAGE_NO_NCQ_ON_ATI for Samsung 860 and 870 SSD.
libata: add ATA_HORKAGE_NO_NCQ_TRIM for Samsung 860 and 870 SSDs
Merge tag 'for-5.15/io_uring-2021-09-04' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"As sometimes happens, two reports came in around the merge window open
that led to some fixes. Hence this one is a bit bigger than usual
followup fixes, but most of it will be going towards stable, outside
of the fixes that are addressing regressions from this merge window.
In detail:
- postgres is a heavy user of signals between tasks, and if we're
unlucky this can interfere with io-wq worker creation. Make sure
we're resilient against unrelated signal handling. This set of
changes also includes hardening against allocation failures, which
could previously had led to stalls.
- Some use cases that end up having a mix of bounded and unbounded
work would have starvation issues related to that. Split the
pending work lists to handle that better.
- Completion trace int -> unsigned -> long fix
- Fix issue with REGISTER_IOWQ_MAX_WORKERS and SQPOLL
- Fix regression with hash wait lock in this merge window
- Fix retry issued on block devices (Ming)
- Fix regression with links in this merge window (Pavel)
- Fix race with multi-shot poll and completions (Xiaoguang)
- Ensure submissions are flushed after running task_work (Pavel)"
* tag 'for-5.15/io_uring-2021-09-04' of git://git.kernel.dk/linux-block:
io_uring: io_uring_complete() trace should take an integer
io_uring: fix possible poll event lost in multi shot mode
io_uring: prolong tctx_task_work() with flushing
io_uring: don't disable kiocb_done() CQE batching
io_uring: ensure IORING_REGISTER_IOWQ_MAX_WORKERS works with SQPOLL
io-wq: make worker creation resilient against signals
io-wq: get rid of FIXED worker flag
io-wq: only exit on fatal signals
io-wq: split bounded and unbounded work into separate lists
io-wq: fix queue stalling race
io_uring: don't submit half-prepared drain request
io_uring: fix queueing half-created requests
io-wq: ensure that hash wait lock is IRQ disabling
io_uring: retry in case of short read on block device
io_uring: IORING_OP_WRITE needs hash_reg_file set
io-wq: fix race between adding work and activating a free worker
projects / mirror_ubuntu-jammy-kernel.git / log