Dongseok Yi [Fri, 29 Jan 2021 23:13:27 +0000 (08:13 +0900)]
udp: ipv4: manipulate network header of NATed UDP GRO fraglist
UDP/IP header of UDP GROed frag_skbs are not updated even after NAT
forwarding. Only the header of head_skb from ip_finish_output_gso ->
skb_gso_segment is updated but following frag_skbs are not updated.
A call path skb_mac_gso_segment -> inet_gso_segment ->
udp4_ufo_fragment -> __udp_gso_segment -> __udp_gso_segment_list
does not try to update UDP/IP header of the segment list but copy
only the MAC header.
Update port, addr and check of each skb of the segment list in
__udp_gso_segment_list. It covers both SNAT and DNAT.
Vadim Fedorenko [Fri, 29 Jan 2021 22:27:47 +0000 (01:27 +0300)]
net: ip_tunnel: fix mtu calculation
dev->hard_header_len for tunnel interface is set only when header_ops
are set too and already contains full overhead of any tunnel encapsulation.
That's why there is not need to use this overhead twice in mtu calc.
Fixes: fdafed459998 ("ip_gre: set dev->hard_header_len and dev->needed_headroom properly") Reported-by: Slava Bacherikov <mail@slava.cc> Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru> Link: https://lore.kernel.org/r/1611959267-20536-1-git-send-email-vfedorenko@novek.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexander Popov [Mon, 1 Feb 2021 08:47:19 +0000 (11:47 +0300)]
vsock: fix the race conditions in multi-transport support
There are multiple similar bugs implicitly introduced by the
commit c0cfa2d8a788fcf4 ("vsock: add multi-transports support") and
commit 6a2c0962105ae8ce ("vsock: prevent transport modules unloading").
The bug pattern:
[1] vsock_sock.transport pointer is copied to a local variable,
[2] lock_sock() is called,
[3] the local variable is used.
VSOCK multi-transport support introduced the race condition:
vsock_sock.transport value may change between [1] and [2].
Let's copy vsock_sock.transport pointer to local variables after
the lock_sock() call.
net: sched: replaced invalid qdisc tree flush helper in qdisc_replace
Commit e5f0e8f8e456 ("net: sched: introduce and use qdisc tree flush/purge helpers")
introduced qdisc tree flush/purge helpers, but erroneously used flush helper
instead of purge helper in qdisc_replace function.
This issue was found in our CI, that tests various qdisc setups by configuring
qdisc and sending data through it. Call of invalid helper sporadically leads
to corruption of vt_tree/cf_tree of hfsc_class that causes kernel oops:
Lijun Pan [Fri, 29 Jan 2021 04:34:01 +0000 (22:34 -0600)]
ibmvnic: device remove has higher precedence over reset
Returning -EBUSY in ibmvnic_remove() does not actually hold the
removal procedure since driver core doesn't care for the return
value (see __device_release_driver() in drivers/base/dd.c
calling dev->bus->remove()) though vio_bus_remove
(in arch/powerpc/platforms/pseries/vio.c) records the
return value and passes it on. [1]
During the device removal precedure, checking for resetting
bit is dropped so that we can continue executing all the
cleanup calls in the rest of the remove function. Otherwise,
it can cause latent memory leaks and kernel crashes.
[1] https://lore.kernel.org/linuxppc-dev/20210117101242.dpwayq6wdgfdzirl@pengutronix.de/T/#m48f5befd96bc9842ece2a3ad14f4c27747206a53 Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Fixes: 7d7195a026ba ("ibmvnic: Do not process device remove during device reset") Signed-off-by: Lijun Pan <ljp@linux.ibm.com> Link: https://lore.kernel.org/r/20210129043402.95744-1-ljp@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
DENG Qingfang [Sat, 30 Jan 2021 13:43:34 +0000 (21:43 +0800)]
net: dsa: mv88e6xxx: override existent unicast portvec in port_fdb_add
Having multiple destination ports for a unicast address does not make
sense.
Make port_db_load_purge override existent unicast portvec instead of
adding a new port bit.
Fixes: 884729399260 ("net: dsa: mv88e6xxx: handle multiple ports in ATU") Signed-off-by: DENG Qingfang <dqfext@gmail.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Link: https://lore.kernel.org/r/20210130134334.10243-1-dqfext@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Chinmay Agarwal [Wed, 27 Jan 2021 16:54:54 +0000 (22:24 +0530)]
neighbour: Prevent a dead entry from updating gc_list
Following race condition was detected:
<CPU A, t0> - neigh_flush_dev() is under execution and calls
neigh_mark_dead(n) marking the neighbour entry 'n' as dead.
<CPU B, t1> - Executing: __netif_receive_skb() ->
__netif_receive_skb_core() -> arp_rcv() -> arp_process().arp_process()
calls __neigh_lookup() which takes a reference on neighbour entry 'n'.
<CPU A, t2> - Moves further along neigh_flush_dev() and calls
neigh_cleanup_and_release(n), but since reference count increased in t2,
'n' couldn't be destroyed.
<CPU B, t3> - Moves further along, arp_process() and calls
neigh_update()-> __neigh_update() -> neigh_update_gc_list(), which adds
the neighbour entry back in gc_list(neigh_mark_dead(), removed it
earlier in t0 from gc_list)
This leads to 'n' still being part of gc_list, but the actual
neighbour structure has been freed.
The situation can be prevented from happening if we disallow a dead
entry to have any possibility of updating gc_list. This is what the
patch intends to achieve.
Fixes: 9c29a2f55ec0 ("neighbor: Fix locking order for gc_list changes") Signed-off-by: Chinmay Agarwal <chinagar@codeaurora.org> Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20210127165453.GA20514@chinagar-linux.qualcomm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
David Howells [Fri, 29 Jan 2021 23:53:50 +0000 (23:53 +0000)]
rxrpc: Fix deadlock around release of dst cached on udp tunnel
AF_RXRPC sockets use UDP ports in encap mode. This causes socket and dst
from an incoming packet to get stolen and attached to the UDP socket from
whence it is leaked when that socket is closed.
When a network namespace is removed, the wait for dst records to be cleaned
up happens before the cleanup of the rxrpc and UDP socket, meaning that the
wait never finishes.
Fix this by moving the rxrpc (and, by dependence, the afs) private
per-network namespace registrations to the device group rather than subsys
group. This allows cached rxrpc local endpoints to be cleared and their
UDP sockets closed before we try waiting for the dst records.
The symptom is that lines looking like the following:
unregister_netdevice: waiting for lo to become free
get emitted at regular intervals after running something like the
referenced syzbot test.
Thanks to Vadim for tracking this down and work out the fix.
Reported-by: syzbot+df400f2f24a1677cd7e0@syzkaller.appspotmail.com Reported-by: Vadim Fedorenko <vfedorenko@novek.ru> Fixes: 5271953cad31 ("rxrpc: Use the UDP encap_rcv hook") Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Vadim Fedorenko <vfedorenko@novek.ru> Link: https://lore.kernel.org/r/161196443016.3868642.5577440140646403533.stgit@warthog.procyon.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiner Kallweit [Thu, 28 Jan 2021 22:01:54 +0000 (23:01 +0100)]
r8169: work around RTL8125 UDP hw bug
It was reported that on RTL8125 network breaks under heavy UDP load,
e.g. torrent traffic ([0], from comment 27). Realtek confirmed a hw bug
and provided me with a test version of the r8125 driver including a
workaround. Tests confirmed that the workaround fixes the issue.
I modified the original version of the workaround to meet mainline
code style.
v2:
- rebased to net
v3:
- make rtl_skb_is_udp() more robust and use skb_header_pointer()
to access the ip(v6) header
v4:
- remove dependency on ptp_classify.h
- replace magic number with offsetof(struct udphdr, len)
Fixes: f1bce4ad2f1c ("r8169: add support for RTL8125") Tested-by: xplo <xplo.bn@gmail.com> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/6e453d49-1801-e6de-d5f7-d7e6c7526c8f@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ahmed S. Darwish [Thu, 28 Jan 2021 19:48:02 +0000 (20:48 +0100)]
net: arcnet: Fix RESET flag handling
The main arcnet interrupt handler calls arcnet_close() then
arcnet_open(), if the RESET status flag is encountered.
This is invalid:
1) In general, interrupt handlers should never call ->ndo_stop() and
->ndo_open() functions. They are usually full of blocking calls and
other methods that are expected to be called only from drivers
init and exit code paths.
2) arcnet_close() contains a del_timer_sync(). If the irq handler
interrupts the to-be-deleted timer, del_timer_sync() will just loop
forever.
3) arcnet_close() also calls tasklet_kill(), which has a warning if
called from irq context.
4) For device reset, the sequence "arcnet_close(); arcnet_open();" is
not complete. Some children arcnet drivers have special init/exit
code sequences, which then embed a call to arcnet_open() and
arcnet_close() accordingly. Check drivers/net/arcnet/com20020.c.
Run the device RESET sequence from a scheduled workqueue instead.
1) Fix two copy_{from,to}_user() warn_on_once splats for BPF cgroup getsockopt
infra when user space is trying to race against optlen, from Loris Reiff.
2) Fix a missing fput() in BPF inode storage map update helper, from Pan Bian.
3) Fix a build error on unresolved symbols on disabled networking / keys LSM
hooks, from Mikko Ylinen.
4) Fix preload BPF prog build when the output directory from make points to a
relative path, from Quentin Monnet.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf, preload: Fix build when $(O) points to a relative path
bpf: Drop disabled LSM hooks from the sleepable set
bpf, inode_storage: Put file handler if no storage was found
bpf, cgroup: Fix problematic bounds check
bpf, cgroup: Fix optlen WARN_ON_ONCE toctou
====================
Linus Torvalds [Thu, 28 Jan 2021 23:24:43 +0000 (15:24 -0800)]
Merge tag 'net-5.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes including fixes from can, xfrm, wireless,
wireless-drivers and netfilter trees. Nothing scary, Intel
WiFi-related fixes seemed most notable to the users.
Current release - regressions:
- dsa: microchip: ksz8795: fix KSZ8794 port map again to program the
CPU port correctly
Current release - new code bugs:
- iwlwifi: pcie: reschedule in long-running memory reads
Previous releases - regressions:
- iwlwifi: dbg: don't try to overwrite read-only FW data
- iwlwifi: provide gso_type to GSO packets
- octeontx2: make sure the buffer is 128 byte aligned
- tcp: make TCP_USER_TIMEOUT accurate for zero window probes
- xfrm: fix wraparound in xfrm_policy_addr_delta()
- xfrm: fix oops in xfrm_replay_advance_bmp due to a race between
CPUs in presence of packet reorder
- tcp: fix TLP timer not set when CA_STATE changes from DISORDER to
OPEN
- wext: fix NULL-ptr-dereference with cfg80211's lack of commit()
Previous releases - always broken:
- igc: fix link speed advertising
- stmmac: configure EHL PSE0 GbE and PSE1 GbE to 32 bits DMA
addressing
- team: protect features update by RCU to avoid deadlock
- xfrm: fix disable_xfrm sysctl when used on xfrm interfaces
themselves
- fec: fix temporary RMII clock reset on link up
- can: dev: prevent potential information leak in can_fill_info()
Misc:
- mrp: fix bad packing of MRP test packet structures
- uapi: fix big endian definition of ipv6_rpl_sr_hdr
- add David Ahern to IPv4/IPv6 maintainers"
* tag 'net-5.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (86 commits)
rxrpc: Fix memory leak in rxrpc_lookup_local
mlxsw: spectrum_span: Do not overwrite policer configuration
selftests: forwarding: Specify interface when invoking mausezahn
stmmac: intel: Configure EHL PSE0 GbE and PSE1 GbE to 32 bits DMA addressing
net: usb: cdc_ether: added support for Thales Cinterion PLSx3 modem family.
ibmvnic: Ensure that CRQ entry read are correctly ordered
MAINTAINERS: add missing header for bonding
net: decnet: fix netdev refcount leaking on error path
net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP
can: dev: prevent potential information leak in can_fill_info()
net: fec: Fix temporary RMII clock reset on link up
net: lapb: Add locking to the lapb module
team: protect features update by RCU to avoid deadlock
MAINTAINERS: add David Ahern to IPv4/IPv6 maintainers
net/mlx5: CT: Fix incorrect removal of tuple_nat_node from nat rhashtable
net/mlx5e: Revert parameters on errors when changing MTU and LRO state without reset
net/mlx5e: Revert parameters on errors when changing trust state without reset
net/mlx5e: Correctly handle changing the number of queues when the interface is down
net/mlx5e: Fix CT rule + encap slow path offload and deletion
net/mlx5e: Disable hw-tc-offload when MLX5_CLS_ACT config is disabled
...
Takeshi Misawa [Thu, 28 Jan 2021 10:48:36 +0000 (10:48 +0000)]
rxrpc: Fix memory leak in rxrpc_lookup_local
Commit 9ebeddef58c4 ("rxrpc: rxrpc_peer needs to hold a ref on the rxrpc_local record")
Then release ref in __rxrpc_put_peer and rxrpc_put_peer_locked.
Fixes: 9ebeddef58c4 ("rxrpc: rxrpc_peer needs to hold a ref on the rxrpc_local record") Signed-off-by: Takeshi Misawa <jeliantsurux@gmail.com> Reported-and-tested-by: syzbot+305326672fed51b205f7@syzkaller.appspotmail.com Signed-off-by: David Howells <dhowells@redhat.com> Link: https://lore.kernel.org/r/161183091692.3506637.3206605651502458810.stgit@warthog.procyon.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 28 Jan 2021 21:09:03 +0000 (13:09 -0800)]
Merge branch 'mlxsw-various-fixes'
Ido Schimmel says:
====================
mlxsw: Various fixes
Patch #1 fixes wrong invocation of mausezahn in a couple of selftests.
The tests started failing after Fedora updated their libnet package from
version 1.1.6 to 1.2.1. With the fix the tests pass regardless of libnet
version.
Patch #2 fixes an issue in the mirroring to CPU code that results in
policer configuration being overwritten.
====================
Ido Schimmel [Thu, 28 Jan 2021 14:48:20 +0000 (16:48 +0200)]
mlxsw: spectrum_span: Do not overwrite policer configuration
The purpose of the delayed work in the SPAN module is to potentially
update the destination port and various encapsulation parameters of SPAN
agents that point to a VLAN device or a GRE tap. The destination port
can change following the insertion of a new route, for example.
SPAN agents that point to a physical port or the CPU port are static and
never change throughout the lifetime of the SPAN agent. Therefore, skip
over them in the delayed work.
This fixes an issue where the delayed work overwrites the policer
that was set on a SPAN agent pointing to the CPU. Modifying the delayed
work to inherit the original policer configuration is error-prone, as
the same will be needed for any new parameter.
Fixes: 4039504e6a0c ("mlxsw: spectrum_span: Allow setting policer on a SPAN agent") Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Danielle Ratson [Thu, 28 Jan 2021 14:48:19 +0000 (16:48 +0200)]
selftests: forwarding: Specify interface when invoking mausezahn
Specify the interface through which packets should be transmitted so
that the test will pass regardless of the libnet version against which
mausezahn is linked.
Fixes: cab14d1087d9 ("selftests: Add version of router_multipath.sh using nexthop objects") Fixes: 3d578d879517 ("selftests: forwarding: Test IPv4 weighted nexthops") Signed-off-by: Danielle Ratson <danieller@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Thu, 28 Jan 2021 19:18:43 +0000 (11:18 -0800)]
Merge tag 'locking-urgent-2021-01-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"A set of PI futex fixes:
- Address a longstanding issue where the user space part of the PI
futex is not writeable. The kernel returns with inconsistent state
which can in the worst case result in a UAF of a tasks kernel
stack.
The solution is to establish consistent kernel state which makes
future operations on the futex fail because user space and kernel
space state are inconsistent. Not a problem as PI futexes
fundamentaly require a functional RW mapping and if user space
pulls the rug under it, then it can keep the pieces it asked for.
- Address an issue where the return value is incorrect in case that
the futex was acquired after a timeout/signal made the waiter drop
out of the rtmutex wait.
In one of the corner cases the kernel returned an error code
despite having successfully acquired the futex"
* tag 'locking-urgent-2021-01-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Handle faults correctly for PI futexes
futex: Simplify fixup_pi_state_owner()
futex: Use pi_state_update_owner() in put_pi_state()
rtmutex: Remove unused argument from rt_mutex_proxy_unlock()
futex: Provide and use pi_state_update_owner()
futex: Replace pointless printk in fixup_owner()
futex: Ensure the correct return value from futex_lock_pi()
Linus Torvalds [Thu, 28 Jan 2021 18:08:08 +0000 (10:08 -0800)]
Merge tag 'for-linus-5.11-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- A fix for a regression introduced in 5.11 resulting in Xen dom0
having problems to correctly initialize Xenstore.
- A fix for avoiding WARN splats when booting as Xen dom0 with
CONFIG_AMD_MEM_ENCRYPT enabled due to a missing trap handler for the
#VC exception (even if the handler should never be called).
- A fix for the Xen bklfront driver adapting to the correct but
unexpected behavior of new qemu.
* tag 'for-linus-5.11-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: avoid warning in Xen pv guest with CONFIG_AMD_MEM_ENCRYPT enabled
xen: Fix XenStore initialisation for XS_LOCAL
xen-blkfront: allow discard-* nodes to be optional
Linus Torvalds [Thu, 28 Jan 2021 18:00:26 +0000 (10:00 -0800)]
Merge tag 'asm-generic-fixes-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull ia64 fixes from Arnd Bergmann:
"asm-generic/ia64 fixes, and mark as orphaned
Commit 2b49ddcef297 ("ia64: convert to legacy_timer_tick") from my
timer series I merged through the asm-generic tree caused a regression
on all ia64 machines, as bisected by Adrian Glaubitz.
Tony Luck is no longer really working on ia64, so instead of merging
the fix through his tree, we ended up deciding that I'd merge the fix
myself along a patch to mark the architecture as Orphaned and a
compile time warning fix I made while working on the regression"
[ HPE no longer accepts orders for new Itanium hardware, and Intel
stopped accepting orders a year ago. While intel is still officially
shipping chips until July 29, 2021, it's unlikely that any such orders
actually exist.
It's dead, Jim.
- Linus ]
* tag 'asm-generic-fixes-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
ia64: Mark architecture as orphaned
ia64: fix xchg() warning
ia64: fix timer cleanup regression
Linus Torvalds [Thu, 28 Jan 2021 17:57:33 +0000 (09:57 -0800)]
Merge tag 'arm-soc-fixes-v5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"These are the current arm-soc bug fixes for linux-5.11. I already
merged a larger set that just came in during the past three days but
has not had much exposure in linux-next, but this is the subset I
merged last week.
Most of these are for the NXP i.MX platform (descriptions from their
pull request):
- Fix pcf2127 reset for imx7d-flex-concentrator board.
- Fix i.MX6 suspend with Thumb-2 kernel.
- Fix ethernet-phy address issue on imx6qdl-sr-som board.
- Fix GPIO3 `gpio-ranges` on i.MX8MP.
- Select SOC_BUS for IMX_SCU driver to fix build issue.
- Fix backlight pwm on imx6qdl-kontron-samx6i which is lost from
#pwm-cells conversion.
- Fix duplicated bus node name for i.MX8MN SoC.
- Fix reset register offset on LS1028A SoC.
- Rename MMC node aliases for imx6q-tbs2910 to keep the MMC device
index consistent with previous kernel version.
- Selecting ARM_GIC_V3 on non-CP15 processors to fix one build
failure with i.MX8M SoC driver.
- Fix typos with status property on imx6qdl-kontron-samx6i board.
- Fix duplicated regulator-name on imx6qdl-gw52xx board.
Aside from i.MX, the bugfixes are all over the place:
- Coccinelle found a refcount imbalance on integrator
- defconfig fix for TI K3
- A boot regression fix for ST ux500
- A code preemption fix for the optee driver
- USB DMA regression on Broadcom Stingray
- A bogus boot time warning fix for at91 code"
* tag 'arm-soc-fixes-v5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
MAINTAINERS: Include bcm2835 subsequents into search
arm64: dts: broadcom: Fix USB DMA address translation for Stingray
drivers: soc: atmel: add null entry at the end of at91_soc_allowed_list[]
drivers: soc: atmel: Avoid calling at91_soc_init on non AT91 SoCs
tee: optee: replace might_sleep with cond_resched
firmware: imx: select SOC_BUS to fix firmware build
arm64: dts: imx8mp: Correct the gpio ranges of gpio3
ARM: dts: imx6qdl-sr-som: fix some cubox-i platforms
ARM: imx: build suspend-imx6.S with arm instruction set
ARM: dts: imx7d-flex-concentrator: fix pcf2127 reset
ARM: dts: ux500: Reserve memory carveouts
arm64: defconfig: Drop unused K3 SoC specific options
bus: arm-integrator-lm: Add of_node_put() before return statement
ARM: dts: imx6qdl-gw52xx: fix duplicate regulator naming
ARM: dts: imx6qdl-kontron-samx6i: fix i2c_lcd/cam default status
ARM: imx: fix imx8m dependencies
ARM: dts: tbs2910: rename MMC node aliases
arm64: dts: ls1028a: fix the offset of the reset register
arm64: dts: imx8mn: Fix duplicate node name
ARM: dts: imx6qdl-kontron-samx6i: fix pwms for lcd-backlight
Linus Torvalds [Thu, 28 Jan 2021 17:27:26 +0000 (09:27 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Several recent regressions and some bug fixes:
- Typo corrupting the max_recv_sge for cxgb4
- Regression from re-using kernel enums as a HW AbI in vmw_pvrdma
- Sleeping inside a spinlock in hns
- Revert the attempt to fix devlink deadlocks as the fix is more buggy
- Typo in sysfs_emit_at conversions
- Revert the removal of VLAN support in rxe"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
Revert "RDMA/rxe: Remove VLAN code leftovers from RXE"
RDMA/usnic: Fix misuse of sysfs_emit_at
Revert "RDMA/mlx5: Fix devlink deadlock on net namespace deletion"
RDMA/hns: Use mutex instead of spinlock for ida allocation
RDMA/vmw_pvrdma: Fix network_hdr_type reported in WC
RDMA/cxgb4: Fix the reported max_recv_sge value
Linus Torvalds [Thu, 28 Jan 2021 17:18:05 +0000 (09:18 -0800)]
Merge tag 'media/v5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- a V4L2 core regression at videobuf2 when checking for single-plane
dmabuf
- a change at uAPI header v4l2-subdev.h, fixing a breakage as BIT()
macro is not available in userspace
- fix some regressions at RC core due to the usage of microseconds
everywhere on it
- a fix for a race condition at RC core
- a rename on a newly-introduced kAPI symbol (v4l2_get_link_rate),
currently used only by a single driver
- Regression fixes for rcar-vin, cedrus, ite-cir, hantro, css, venus,
and cec drivers.
* tag 'media/v5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: hantro: Fix reset_raw_fmt initialization
media: cec: add stm32 driver
media: cedrus: Fix H264 decoding
media: v4l2-subdev.h: BIT() is not available in userspace
media: Revert "media: videobuf2: Fix length check for single plane dmabuf queueing"
media: rc: ite-cir: fix min_timeout calculation
media: venus: core: Fix platform driver shutdown
media: rc: fix timeout handling after switch to microsecond durations
media: v4l: common: Fix naming of v4l2_get_link_rate
media: rcar-vin: fix return, use ret instead of zero
media: ccs: Get static data version minor correctly
media: ccs-pll: Fix link frequency for C-PHY
media: rc: ensure that uevent can be read directly after rc device register
Linus Torvalds [Thu, 28 Jan 2021 17:14:58 +0000 (09:14 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of clk driver fixes:
- Build fix for CONFIG_PM=n in the mmp2 driver
- Kconfig warning for unmet dependencies in the i.MX driver
- Make the camera AHB clk always be enabled on qcom sc7180
- Use rate round down semantics for qcom sm8250 SD clks"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: mmp2: fix build without CONFIG_PM
clk: qcom: gcc-sm250: Use floor ops for sdcc clks
clk: imx: fix Kconfig warning for i.MX SCU clk
clk: qcom: gcc-sc7180: Mark the camera abh clock always ON
Linus Torvalds [Thu, 28 Jan 2021 17:06:52 +0000 (09:06 -0800)]
Merge tag 'sound-5.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Although the incoming fixes haven't settled down yet, all changes here
are small and mostly device-specific fixes, so nothing look worrisome.
- Yet another USB-audio regression fixes
- HD-audio ID fix and device-specific quirks
- SOF Intel / SoundWire fixes including topology
- ASoC Qualcomm and Mediatek fixes"
* tag 'sound-5.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (24 commits)
ALSA: hda/via: Apply the workaround generically for Clevo machines
ASoC: Intel: sof_sdw: set proper flags for Dell TGL-H SKU 0A5E
ASoC: qcom: lpass: Fix out-of-bounds DAI ID lookup
ASoC: mediatek: mt8192-mt6359: add format constraints for RT5682
ASoC: ak4458: correct reset polarity
ASoC: SOF: SND_INTEL_DSP_CONFIG dependency
ASoC: SOF: Intel: soundwire: fix select/depend unmet dependencies
ALSA: hda: intel-dsp-config: add PCI id for TGL-H
ALSA: usb-audio: workaround for iface reset issue
ALSA: pcm: One more dependency for hw constraints
ALSA: hda/realtek: Enable headset of ASUS B1400CEPE with ALC256
ASoC: Intel: Skylake: Zero snd_ctl_elem_value
ASoC: Intel: Skylake: skl-topology: Fix OOPs ib skl_tplg_complete
ASoC: qcom: Fix number of HDMI RDMA channels on sc7180
ASoC: mediatek: mt8183-da7219: ignore TDM DAI link by default
ASoC: mediatek: mt8183-mt6358: ignore TDM DAI link by default
ASoC: topology: Properly unregister DAI on removal
ASoC: topology: Fix memory corruption in soc_tplg_denum_create_values()
ASoC: qcom: lpass-ipq806x: fix bitwidth regmap field
ASoC: AMD Renoir - refine DMI entries for some Lenovo products
...
Jakub Kicinski [Thu, 28 Jan 2021 03:18:37 +0000 (19:18 -0800)]
Merge tag 'mlx5-fixes-2021-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2021-01-26
This series introduces some fixes to mlx5 driver.
* tag 'mlx5-fixes-2021-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: CT: Fix incorrect removal of tuple_nat_node from nat rhashtable
net/mlx5e: Revert parameters on errors when changing MTU and LRO state without reset
net/mlx5e: Revert parameters on errors when changing trust state without reset
net/mlx5e: Correctly handle changing the number of queues when the interface is down
net/mlx5e: Fix CT rule + encap slow path offload and deletion
net/mlx5e: Disable hw-tc-offload when MLX5_CLS_ACT config is disabled
net/mlx5: Maintain separate page trees for ECPF and PF functions
net/mlx5e: Fix IPSEC stats
net/mlx5e: Reduce tc unsupported key print level
net/mlx5e: free page before return
net/mlx5e: E-switch, Fix rate calculation for overflow
net/mlx5: Fix memory leak on flow table creation error flow
====================
Lijun Pan [Thu, 28 Jan 2021 01:34:42 +0000 (19:34 -0600)]
ibmvnic: Ensure that CRQ entry read are correctly ordered
Ensure that received Command-Response Queue (CRQ) entries are
properly read in order by the driver. dma_rmb barrier has
been added before accessing the CRQ descriptor to ensure
the entire descriptor is read before processing.
1) Honor stateful expressions defined in the set from the dynset
extension. The set definition provides a stateful expression
that must be used by the dynset expression in case it is specified.
2) Missing timeout extension in the set element in the dynset
extension leads to inconsistent ruleset listing, not allowing
the user to restore timeout and expiration on ruleset reload.
3) Do not dump the stateful expression from the dynset extension
if it coming from the set definition.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf:
netfilter: nft_dynset: dump expressions when set definition contains no expressions
netfilter: nft_dynset: add timeout extension to template
netfilter: nft_dynset: honor stateful expressions in set definition
====================
Jakub Kicinski [Thu, 28 Jan 2021 01:51:45 +0000 (17:51 -0800)]
Merge tag 'linux-can-fixes-for-5.11-20210127' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2021-01-27
The patch is by Dan Carpenter and fixes a potential information leak in
can_fill_info().
* tag 'linux-can-fixes-for-5.11-20210127' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: dev: prevent potential information leak in can_fill_info()
====================
Jakub Kicinski [Thu, 28 Jan 2021 01:44:51 +0000 (17:44 -0800)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Anthony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-01-26
This series contains updates to the ice, i40e, and igc driver.
Henry corrects setting an unspecified protocol to IPPROTO_NONE instead of
0 for IPv6 flexbytes filters for ice.
Nick fixes the IPv6 extension header being processed incorrectly and
updates the netdev->dev_addr if it exists in hardware as it may have been
modified outside the ice driver.
Brett ensures a user cannot request more channels than available LAN MSI-X
and fixes the minimum allocation logic as it was incorrectly trying to use
more MSI-X than allocated for ice.
Stefan Assmann minimizes the delay between getting and using the VSI
pointer to prevent a possible crash for i40e.
Corinna Vinschen fixes link speed advertising for igc.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: fix link speed advertising
i40e: acquire VSI pointer only after VF is initialized
ice: Fix MSI-X vector fallback logic
ice: Don't allow more channels than LAN MSI-X available
ice: update dev_addr in ice_set_mac_address even if HW filter exists
ice: Implement flow for IPv6 next header (extension header)
ice: fix FDir IPv6 flexbyte
====================
Vadim Fedorenko [Tue, 26 Jan 2021 00:02:14 +0000 (03:02 +0300)]
net: decnet: fix netdev refcount leaking on error path
On building the route there is an assumption that the destination
could be local. In this case loopback_dev is used to get the address.
If the address is still cannot be retrieved dn_route_output_slow
returns EADDRNOTAVAIL with loopback_dev reference taken.
Cannot find hash for the fixes tag because this code was introduced
long time ago. I don't think that this bug has ever fired but the
patch is done just to have a consistent code base.
Rasmus Villemoes [Mon, 25 Jan 2021 12:41:16 +0000 (13:41 +0100)]
net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP
It's not true that switchdev_port_obj_notify() only inspects the
->handled field of "struct switchdev_notifier_port_obj_info" if
call_switchdev_blocking_notifiers() returns 0 - there's a WARN_ON()
triggering for a non-zero return combined with ->handled not being
true. But the real problem here is that -EOPNOTSUPP is not being
properly handled.
The wrapper functions switchdev_handle_port_obj_add() et al change a
return value of -EOPNOTSUPP to 0, and the treatment of ->handled in
switchdev_port_obj_notify() seems to be designed to change that back
to -EOPNOTSUPP in case nobody actually acted on the notifier (i.e.,
everybody returned -EOPNOTSUPP).
Currently, as soon as some device down the stack passes the check_cb()
check, ->handled gets set to true, which means that
switchdev_port_obj_notify() cannot actually ever return -EOPNOTSUPP.
This, for example, means that the detection of hardware offload
support in the MRP code is broken: switchdev_port_obj_add() used by
br_mrp_switchdev_send_ring_test() always returns 0, so since the MRP
code thinks the generation of MRP test frames has been offloaded, no
such frames are actually put on the wire. Similarly,
br_mrp_switchdev_set_ring_role() also always returns 0, causing
mrp->ring_role_offloaded to be set to 1.
To fix this, continue to set ->handled true if any callback returns
success or any error distinct from -EOPNOTSUPP. But if all the
callbacks return -EOPNOTSUPP, make sure that ->handled stays false, so
the logic in switchdev_port_obj_notify() can propagate that
information.
Fixes: 9a9f26e8f7ea ("bridge: mrp: Connect MRP API with the switchdev API") Fixes: f30f0601eb93 ("switchdev: Add helpers to aid traversal through lower devices") Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Link: https://lore.kernel.org/r/20210125124116.102928-1-rasmus.villemoes@prevas.dk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Wed, 27 Jan 2021 19:06:15 +0000 (11:06 -0800)]
Merge branch 'parisc-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"Two small fixes:
- Fix linking error with 64-bit kernel when modules are disabled,
reported by kernel test robot
- Remove leftover reference to power_tasklet, by Davidlohr Bueso"
* 'parisc-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Enable -mlong-calls gcc option by default when !CONFIG_MODULES
parisc: Remove leftover reference to the power_tasklet
Reason is that there is no Xen pv trap entry for X86_TRAP_VC.
Fix that by adding a generic trap handler for unknown traps and wire all
unknown bare metal handlers to this generic handler, which will just
crash the system in case such a trap will ever happen.
Fixes: 0786138c78e793 ("x86/sev-es: Add a Runtime #VC Exception Handler") Cc: <stable@vger.kernel.org> # v5.10 Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com> Signed-off-by: Juergen Gross <jgross@suse.com>
Dan Carpenter [Thu, 21 Jan 2021 06:08:05 +0000 (09:08 +0300)]
can: dev: prevent potential information leak in can_fill_info()
The "bec" struct isn't necessarily always initialized. For example, the
mcp251xfd_get_berr_counter() function doesn't initialize anything if the
interface is down.
Fixes: 52c793f24054 ("can: netlink support for bus-error reporting and counters") Link: https://lore.kernel.org/r/YAkaRdRJncsJO8Ve@mwanda Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
David Woodhouse [Tue, 26 Jan 2021 17:01:49 +0000 (17:01 +0000)]
xen: Fix XenStore initialisation for XS_LOCAL
In commit 3499ba8198ca ("xen: Fix event channel callback via INTX/GSI")
I reworked the triggering of xenbus_probe().
I tried to simplify things by taking out the workqueue based startup
triggered from wake_waiting(); the somewhat poorly named xenbus IRQ
handler.
I missed the fact that in the XS_LOCAL case (Dom0 starting its own
xenstored or xenstore-stubdom, which happens after the kernel is booted
completely), that IRQ-based trigger is still actually needed.
So... put it back, except more cleanly. By just spawning a xenbus_probe
thread which waits on xb_waitq and runs the probe the first time it
gets woken, just as the workqueue-based hack did.
This is actually a nicer approach for *all* the back ends with different
interrupt methods, and we can switch them all over to that without the
complex conditions for when to trigger it. But not in -rc6. This is
the minimal fix for the regression, although it's a step in the right
direction instead of doing a partial revert and actually putting the
workqueue back. It's also simpler than the workqueue.
====================
net: fec: Fix temporary RMII clock reset on link up
v2: fixed a compilation warning
The FEC drivers performs a "hardware reset" of the MAC module when the
link is reported to be up. This causes a short glitch in the RMII clock
due to the hardware reset clearing the receive control register which
controls the MII mode. It seems that some link partners do not tolerate
this glitch, and invalidate the link, which leads to a never-ending loop
of negotiation-link up-link down events.
This was observed with the iMX28 Soc and LAN8720/LAN8742 PHYs, with two
Intel adapters I218-LM and X722-DA2 as link partners, though a number of
other link partners do not seem to mind the clock glitch. Changing the
hardware reset to a software reset (clearing bit 1 of the ECR register)
cured the issue.
Attempts to optimize fec_restart() in order to minimize the duration of
the glitch were unsuccessful. Furthermore manually producing the glitch by
setting MII mode and then back to RMII in two consecutive instructions,
resulting in a clock glitch <10us in duration, was enough to cause the
partner to invalidate the link. This strongly suggests that the root cause
of the link being dropped is indeed the change in clock frequency.
In an effort to minimize changes to driver, the patch proposes to use
soft reset only for tested SoCs (iMX28) and only if the link is up. This
preserves hardware reset in other situations, which might be required for
proper setup of the MAC.
====================
Laurent Badel [Mon, 25 Jan 2021 10:07:45 +0000 (11:07 +0100)]
net: fec: Fix temporary RMII clock reset on link up
fec_restart() does a hard reset of the MAC module when the link status
changes to up. This temporarily resets the R_CNTRL register which controls
the MII mode of the ENET_OUT clock. In the case of RMII, the clock
frequency momentarily drops from 50MHz to 25MHz until the register is
reconfigured. Some link partners do not tolerate this glitch and
invalidate the link causing failure to establish a stable link when using
PHY polling mode. Since as per IEEE802.3 the criteria for link validity
are PHY-specific, what the partner should tolerate cannot be assumed, so
avoid resetting the MII clock by using software reset instead of hardware
reset when the link is up. This is generally relevant only if the SoC
provides the clock to an external PHY and the PHY is configured for RMII.
Signed-off-by: Laurent Badel <laurentbadel@eaton.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xie He [Tue, 26 Jan 2021 04:09:39 +0000 (20:09 -0800)]
net: lapb: Add locking to the lapb module
In the lapb module, the timers may run concurrently with other code in
this module, and there is currently no locking to prevent the code from
racing on "struct lapb_cb". This patch adds locking to prevent racing.
1. Add "spinlock_t lock" to "struct lapb_cb"; Add "spin_lock_bh" and
"spin_unlock_bh" to APIs, timer functions and notifier functions.
2. Add "bool t1timer_stop, t2timer_stop" to "struct lapb_cb" to make us
able to ask running timers to abort; Modify "lapb_stop_t1timer" and
"lapb_stop_t2timer" to make them able to abort running timers;
Modify "lapb_t2timer_expiry" and "lapb_t1timer_expiry" to make them
abort after they are stopped by "lapb_stop_t1timer", "lapb_stop_t2timer",
and "lapb_start_t1timer", "lapb_start_t2timer".
3. Let lapb_unregister wait for other API functions and running timers
to stop.
4. The lapb_device_event function calls lapb_disconnect_request. In
order to avoid trying to hold the lock twice, add a new function named
"__lapb_disconnect_request" which assumes the lock is held, and make
it called by lapb_disconnect_request and lapb_device_event.
Ivan Vecera [Mon, 25 Jan 2021 07:44:16 +0000 (08:44 +0100)]
team: protect features update by RCU to avoid deadlock
Function __team_compute_features() is protected by team->lock
mutex when it is called from team_compute_features() used when
features of an underlying device is changed. This causes
a deadlock when NETDEV_FEAT_CHANGE notifier for underlying device
is fired due to change propagated from team driver (e.g. MTU
change). It's because callbacks like team_change_mtu() or
team_vlan_rx_{add,del}_vid() protect their port list traversal
by team->lock mutex.
Example (r8169 case where this driver disables TSO for certain MTU
values):
...
[ 6391.348202] __mutex_lock.isra.6+0x2d0/0x4a0
[ 6391.358602] team_device_event+0x9d/0x160 [team]
[ 6391.363756] notifier_call_chain+0x47/0x70
[ 6391.368329] netdev_update_features+0x56/0x60
[ 6391.373207] rtl8169_change_mtu+0x14/0x50 [r8169]
[ 6391.378457] dev_set_mtu_ext+0xe1/0x1d0
[ 6391.387022] dev_set_mtu+0x52/0x90
[ 6391.390820] team_change_mtu+0x64/0xf0 [team]
[ 6391.395683] dev_set_mtu_ext+0xe1/0x1d0
[ 6391.399963] do_setlink+0x231/0xf50
...
In fact team_compute_features() called from team_device_event()
does not need to be protected by team->lock mutex and rcu_read_lock()
is sufficient there for port list traversal.
Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device") Cc: Saeed Mahameed <saeed@kernel.org> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Link: https://lore.kernel.org/r/20210125074416.4056484-1-ivecera@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paul Blakey [Mon, 25 Jan 2021 15:31:26 +0000 (17:31 +0200)]
net/mlx5: CT: Fix incorrect removal of tuple_nat_node from nat rhashtable
If a non nat tuple entry is inserted just to the regular tuples
rhashtable (ct_tuples_ht) and not to natted tuples rhashtable
(ct_nat_tuples_ht). Commit bc562be9674b ("net/mlx5e: CT: Save ct entries
tuples in hashtables") mixed up the return labels and names sot that on
cleanup or failure we still try to remove for the natted tuples rhashtable.
Fix that by correctly checking if a natted tuples insertion
before removing it. While here make it more readable.
Fixes: bc562be9674b ("net/mlx5e: CT: Save ct entries tuples in hashtables") Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Paul Blakey <paulb@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
net/mlx5e: Revert parameters on errors when changing MTU and LRO state without reset
Sometimes, channel params are changed without recreating the channels.
It happens in two basic cases: when the channels are closed, and when
the parameter being changed doesn't affect how channels are configured.
Such changes invoke a hardware command that might fail. The whole
operation should be reverted in such cases, but the code that restores
the parameters' values in the driver was missing. This commit adds this
handling.
net/mlx5e: Revert parameters on errors when changing trust state without reset
Trust state may be changed without recreating the channels. It happens
when the channels are closed, and when channel parameters (min inline
mode) stay the same after changing the trust state. Changing the trust
state is a hardware command that may fail. The current code didn't
restore the channel parameters to their old values if an error happened
and the channels were closed. This commit adds handling for this case.
Currently, if a neighbour isn't valid when offloading tunnel encap rules,
we offload the original match and replace the original action with
"goto slow path" action. For this we use a temporary flow attribute based
on the original flow attribute and then change the action. Flow flags,
which among those is the CT flag, are still shared for the slow path rule
offload, so we end up parsing this flow as a CT + goto slow path rule.
Besides being unnecessary, CT action offload saves extra information in
the passed flow attribute, such as created ct_flow and mod_hdr, which
is lost onces the temporary flow attribute is freed.
When a neigh is updated and is valid, we offload the original CT rule
with original CT action, which again creates a ct_flow and mod_hdr
and saves it in the flow's original attribute. Then we delete the slow
path rule with a temporary flow attribute based on original updated
flow attribute, and we free the relevant ct_flow and mod_hdr.
Then when tc deletes this flow, we try to free the ct_flow and mod_hdr
on the flow's attribute again.
To fix the issue, skip all furture proccesing (CT/Sample/Split rules)
in offload/unoffload of slow path rules.
Maor Dickman [Sun, 24 Jan 2021 15:21:25 +0000 (17:21 +0200)]
net/mlx5e: Disable hw-tc-offload when MLX5_CLS_ACT config is disabled
The cited commit introduce new CONFIG_MLX5_CLS_ACT kconfig variable
to control compilation of TC hardware offloads implementation.
When this configuration is disabled the driver is still wrongly
reports in ethtool that hw-tc-offload is supported.
Fixed by reporting hw-tc-offload is supported only when
CONFIG_MLX5_CLS_ACT is enabled.
Daniel Jurgens [Fri, 22 Jan 2021 21:13:53 +0000 (23:13 +0200)]
net/mlx5: Maintain separate page trees for ECPF and PF functions
Pages for the host PF and ECPF were stored in the same tree, so the ECPF
pages were being freed along with the host PF's when the host driver
unloaded.
Combine the function ID and ECPF flag to use as an index into the
x-array containing the trees to get a different tree for the host PF and
ECPF.
Fixes: c6168161f693 ("net/mlx5: Add support for release all pages event") Signed-off-by: Daniel Jurgens <danielj@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When IPSEC offload isn't active, the number of stats is not zero, but
the strings are not filled, leading to exposing stats with empty names.
Fix this by using the same condition for NUM_STATS and FILL_STRS.
Fixes: 0aab3e1b04ae ("net/mlx5e: IPSec, Expose IPsec HW stat only for supporting HW") Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Reviewed-by: Raed Salem <raeds@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Parav Pandit [Tue, 12 Jan 2021 14:13:22 +0000 (16:13 +0200)]
net/mlx5e: E-switch, Fix rate calculation for overflow
rate_bytes_ps is a 64-bit field. It passed as 32-bit field to
apply_police_params(). Due to this when police rate is higher
than 4Gbps, 32-bit calculation ignores the carry. This results
in incorrect rate configurationn the device.
Jakub Kicinski [Tue, 26 Jan 2021 23:23:17 +0000 (15:23 -0800)]
Merge tag 'mac80211-for-net-2021-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A couple of fixes:
* fix 160 MHz channel switch in mac80211
* fix a staging driver to not deadlock due to some
recent cfg80211 changes
* fix NULL-ptr deref if cfg80211 returns -EINPROGRESS
to wext (syzbot)
* pause TX in mac80211 in type change to prevent crashes
(syzbot)
* tag 'mac80211-for-net-2021-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211:
staging: rtl8723bs: fix wireless regulatory API misuse
mac80211: pause TX while changing interface type
wext: fix NULL-ptr-dereference with cfg80211's lack of commit()
mac80211: 160MHz with extended NSS BW in CSA
====================
Jakub Kicinski [Tue, 26 Jan 2021 23:16:39 +0000 (15:16 -0800)]
Merge tag 'wireless-drivers-2021-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.11
Second set of fixes for v5.11. Like in last time we again have more
fixes than usual Actually a bit too much for my liking in this state
of the cycle, but due to unrelated challenges I was only able to
submit them now.
We have few important crash fixes, iwlwifi modifying read-only data
being the most reported issue, and also smaller fixes to iwlwifi.
mt76
* fix a clang warning about enum usage
* fix rx buffer refcounting crash
mt7601u
* fix rx buffer refcounting crash
* fix crash when unbplugging the device
iwlwifi
* fix a crash where we were modifying read-only firmware data
* lots of smaller fixes all over the driver
* tag 'wireless-drivers-2021-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers: (24 commits)
mt7601u: fix kernel crash unplugging the device
iwlwifi: queue: bail out on invalid freeing
iwlwifi: mvm: guard against device removal in reprobe
iwlwifi: Fix IWL_SUBDEVICE_NO_160 macro to use the correct bit.
iwlwifi: mvm: clear IN_D3 after wowlan status cmd
iwlwifi: pcie: add rules to match Qu with Hr2
iwlwifi: mvm: invalidate IDs of internal stations at mvm start
iwlwifi: mvm: fix the return type for DSM functions 1 and 2
iwlwifi: pcie: reschedule in long-running memory reads
iwlwifi: pcie: use jiffies for memory read spin time limit
iwlwifi: pcie: fix context info memory leak
iwlwifi: pcie: add a NULL check in iwl_pcie_txq_unmap
iwlwifi: pcie: set LTR on more devices
iwlwifi: queue: don't crash if txq->entries is NULL
iwlwifi: fix the NMI flow for old devices
iwlwifi: pnvm: don't try to load after failures
iwlwifi: pnvm: don't skip everything when not reloading
iwlwifi: pcie: avoid potential PNVM leaks
iwlwifi: mvm: take mutex for calling iwl_mvm_get_sync_time()
iwlwifi: mvm: skip power command when unbinding vif during CSA
...
====================
In the case above, for the "bindeb-pkg" target, the error is produced by
the "dummy" check in Makefile.include, called from libbpf's Makefile.
This check changes directory to $(PWD) before checking for the existence
of $(O). But at this step we have $(PWD) pointing to "/.../linux/build",
and $(O) pointing to "build". So the Makefile.include tries in fact to
assert the existence of a directory named "/.../linux/build/build",
which does not exist.
Note that the error does not occur for all make targets and
architectures combinations. This was observed on x86 for "bindeb-pkg",
or for a regular build for UML [0].
Here are some details. The root Makefile recursively calls itself once,
after changing directory to $(O). The content for the variable $(PWD) is
preserved across recursive calls to make, so it is unchanged at this
step. For "bindeb-pkg", $(PWD) is eventually updated because the target
writes a new Makefile (as debian/rules) and calls it indirectly through
dpkg-buildpackage. This script does not preserve $(PWD), which is reset
to the current working directory when the target in debian/rules is
called.
Although not investigated, it seems likely that something similar causes
UML to change its value for $(PWD).
Non-trivial fixes could be to remove the use of $(PWD) from the "dummy"
check, or to make sure that $(PWD) and $(O) are preserved or updated to
always play well and form a valid $(PWD)/$(O) path across the different
targets and architectures. Instead, we take a simpler approach and just
update $(O) when calling libbpf's Makefile, so it points to an absolute
path which should always resolve for the "dummy" check run (through
includes) by that Makefile.
David Gow previously posted a slightly different version of this patch
as a RFC [0], two months ago or so.
Corinna Vinschen [Tue, 17 Nov 2020 19:50:40 +0000 (20:50 +0100)]
igc: fix link speed advertising
Link speed advertising in igc has two problems:
- When setting the advertisement via ethtool, the link speed is converted
to the legacy 32 bit representation for the intel PHY code.
This inadvertently drops ETHTOOL_LINK_MODE_2500baseT_Full_BIT (being
beyond bit 31). As a result, any call to `ethtool -s ...' drops the
2500Mbit/s link speed from the PHY settings. Only reloading the driver
alleviates that problem.
Fix this by converting the ETHTOOL_LINK_MODE_2500baseT_Full_BIT to the
Intel PHY ADVERTISE_2500_FULL bit explicitly.
- Rather than checking the actual PHY setting, the .get_link_ksettings
function always fills link_modes.advertising with all link speeds
the device is capable of.
Fix this by checking the PHY autoneg_advertised settings and report
only the actually advertised speeds up to ethtool.
Remove the magical "repo-abbrev" comment added when this file was
introduced in e0ab1ec9fcd3 ([PATCH] add .mailmap for proper
git-shortlog output, 2007-02-14).
It's been an undocumented feature of git-shortlog(1), originally added
to git for Linus's use. Since then he's no longer using it[1], and
I've removed the feature in git.git's 4e168333a87 (shortlog: remove
unused(?) "repo-abbrev" feature, 2021-01-12). It's on the "master"
branch, but not yet in a release version.
Let's also remove it from linux.git, both as a heads-up to any
potential users of it in linux.git whose use would be broken sooner
than later by git itself, and because it'll eventually be entirely
redundant.
Helge Deller [Tue, 26 Jan 2021 19:16:21 +0000 (20:16 +0100)]
parisc: Enable -mlong-calls gcc option by default when !CONFIG_MODULES
When building a kernel without module support, the CONFIG_MLONGCALL option
needs to be enabled in order to reach symbols which are outside of a 22-bit
branch.
This patch changes the autodetection in the Kconfig script to always enable
CONFIG_MLONGCALL when modules are disabled and uses a far call to
preempt_schedule_irq() in intr_do_preempt() to reach the symbol in all cases.
Linus Torvalds [Tue, 26 Jan 2021 19:10:14 +0000 (11:10 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
- x86 bugfixes
- Documentation fixes
- Avoid performance regression due to SEV-ES patches
- ARM:
- Don't allow tagged pointers to point to memslots
- Filter out ARMv8.1+ PMU events on v8.0 hardware
- Hide PMU registers from userspace when no PMU is configured
- More PMU cleanups
- Don't try to handle broken PSCI firmware
- More sys_reg() to reg_to_encoding() conversions
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: allow KVM_REQ_GET_NESTED_STATE_PAGES outside guest mode for VMX
KVM: x86: Revert "KVM: x86: Mark GPRs dirty when written"
KVM: SVM: Unconditionally sync GPRs to GHCB on VMRUN of SEV-ES guest
KVM: nVMX: Sync unsync'd vmcs02 state to vmcs12 on migration
kvm: tracing: Fix unmatched kvm_entry and kvm_exit events
KVM: Documentation: Update description of KVM_{GET,CLEAR}_DIRTY_LOG
KVM: x86: get smi pending status correctly
KVM: x86/pmu: Fix HW_REF_CPU_CYCLES event pseudo-encoding in intel_arch_events[]
KVM: x86/pmu: Fix UBSAN shift-out-of-bounds warning in intel_pmu_refresh()
KVM: x86: Add more protection against undefined behavior in rsvd_bits()
KVM: Documentation: Fix spec for KVM_CAP_ENABLE_CAP_VM
KVM: Forbid the use of tagged userspace addresses for memslots
KVM: arm64: Filter out v8.1+ events on v8.0 HW
KVM: arm64: Compute TPIDR_EL2 ignoring MTE tag
KVM: arm64: Use the reg_to_encoding() macro instead of sys_reg()
KVM: arm64: Allow PSCI SYSTEM_OFF/RESET to return
KVM: arm64: Simplify handling of absent PMU system registers
KVM: arm64: Hide PMU registers from userspace when not available
Linus Torvalds [Tue, 26 Jan 2021 18:59:01 +0000 (10:59 -0800)]
Merge tag 'regulator-fix-v5.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"The main thing here is a change to make sure that we don't try to
double resolve the supply of a regulator if we have two probes going
on simultaneously, plus an incremental fix on top of that to resolve a
lockdep issue it introduced.
There's also a patch from Dmitry Osipenko adding stubs for some
functions to avoid build issues in consumers in some configurations"
* tag 'regulator-fix-v5.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Fix lockdep warning resolving supplies
regulator: consumer: Add missing stubs to regulator/consumer.h
regulator: core: avoid regulator_resolve_supply() race condition
Stefan Assmann [Mon, 30 Nov 2020 13:12:57 +0000 (14:12 +0100)]
i40e: acquire VSI pointer only after VF is initialized
This change simplifies the VF initialization check and also minimizes
the delay between acquiring the VSI pointer and using it. As known by
the commit being fixed, there is a risk of the VSI pointer getting
changed. Therefore minimize the delay between getting and using the
pointer.
Fixes: 9889707b06ac ("i40e: Fix crash caused by stress setting of VF MAC addresses") Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Brett Creeley [Thu, 21 Jan 2021 18:38:06 +0000 (10:38 -0800)]
ice: Fix MSI-X vector fallback logic
The current MSI-X enablement logic tries to enable best-case MSI-X
vectors and if that fails we only support a bare-minimum set. This
includes a single MSI-X for 1 Tx and 1 Rx queue and a single MSI-X
for the OICR interrupt. Unfortunately, the driver fails to load when we
don't get as many MSI-X as requested for a couple reasons.
First, the code to allocate MSI-X in the driver tries to allocate
num_online_cpus() MSI-X for LAN traffic without caring about the number
of MSI-X actually enabled/requested from the kernel for LAN traffic.
So, when calling ice_get_res() for the PF VSI, it returns failure
because the number of available vectors is less than requested. Fix
this by not allowing the PF VSI to allocation more than
pf->num_lan_msix MSI-X vectors and pf->num_lan_msix Rx/Tx queues.
Limiting the number of queues is done because we don't want more than
1 Tx/Rx queue per interrupt due to performance conerns.
Second, the driver assigns pf->num_lan_msix = 2, to account for LAN
traffic and the OICR. However, pf->num_lan_msix is only meant for LAN
MSI-X. This is causing a failure when the PF VSI tries to
allocate/reserve the minimum pf->num_lan_msix because the OICR MSI-X has
already been reserved, so there may not be enough MSI-X vectors left.
Fix this by setting pf->num_lan_msix = 1 for the failure case. Then the
ICE_MIN_MSIX accounts for the LAN MSI-X and the OICR MSI-X needed for
the failure case.
Update the related defines used in ice_ena_msix_range() to align with
the above behavior and remove the unused RDMA defines because RDMA is
currently not supported. Also, remove the now incorrect comment.
Fixes: 152b978a1f90 ("ice: Rework ice_ena_msix_range") Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Brett Creeley [Thu, 21 Jan 2021 18:38:05 +0000 (10:38 -0800)]
ice: Don't allow more channels than LAN MSI-X available
Currently users could create more channels than LAN MSI-X available.
This is happening because there is no check against pf->num_lan_msix
when checking the max allowed channels and will cause performance issues
if multiple Tx and Rx queues are tied to a single MSI-X. Fix this by not
allowing more channels than LAN MSI-X available in pf->num_lan_msix.
Fixes: 87324e747fde ("ice: Implement ethtool ops for channels") Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Nick Nunley [Sat, 21 Nov 2020 00:38:33 +0000 (16:38 -0800)]
ice: update dev_addr in ice_set_mac_address even if HW filter exists
Fix the driver to copy the MAC address configured in ndo_set_mac_address
into dev_addr, even if the MAC filter already exists in HW. In some
situations (e.g. bonding) the netdev's dev_addr could have been modified
outside of the driver, with no change to the HW filter, so the driver
cannot assume that they match.
Fixes: 757976ab16be ("ice: Fix check for removing/adding mac filters") Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Nick Nunley [Sat, 21 Nov 2020 00:38:31 +0000 (16:38 -0800)]
ice: Implement flow for IPv6 next header (extension header)
This patch is based on a similar change to i40e by Slawomir Laba:
"i40e: Implement flow for IPv6 next header (extension header)".
When a packet contains an IPv6 header with next header which is
an extension header and not a protocol one, the kernel function
skb_transport_header called with such sk_buff will return a
pointer to the extension header and not to the TCP one.
The above explained call caused a problem with packet processing
for skb with encapsulation for tunnel with ICE_TX_CTX_EIPT_IPV6.
The extension header was not skipped at all.
The ipv6_skip_exthdr function does check if next header of the IPV6
header is an extension header and doesn't modify the l4_proto pointer
if it points to a protocol header value so its safe to omit the
comparison of exthdr and l4.hdr pointers. The ipv6_skip_exthdr can
return value -1. This means that the skipping process failed
and there is something wrong with the packet so it will be dropped.
Fixes: a4e82a81f573 ("ice: Add support for tunnel offloads") Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Henry Tieman [Sat, 21 Nov 2020 00:38:30 +0000 (16:38 -0800)]
ice: fix FDir IPv6 flexbyte
The packet classifier would occasionally misrecognize an IPv6 training
packet when the next protocol field was 0. The correct value for
unspecified protocol is IPPROTO_NONE.
Fixes: 165d80d6adab ("ice: Support IPv6 Flow Director filters") Signed-off-by: Henry Tieman <henry.w.tieman@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Jernej Skrabec [Wed, 23 Dec 2020 11:06:59 +0000 (12:06 +0100)]
media: cedrus: Fix H264 decoding
During H264 API overhaul subtle bug was introduced Cedrus driver.
Progressive references have both, top and bottom reference flags set.
Cedrus reference list expects only bottom reference flag and only when
interlaced frames are decoded. However, due to a bug in Cedrus check,
exclusivity is not tested and that flag is set also for progressive
references. That causes "jumpy" background with many videos.
Fix that by checking that only bottom reference flag is set in control
and nothing else.
Takashi Iwai [Tue, 26 Jan 2021 16:56:03 +0000 (17:56 +0100)]
ALSA: hda/via: Apply the workaround generically for Clevo machines
We've got another report indicating a similar problem wrt the
power-saving behavior with VIA codec on Clevo machines. Let's apply
the existing workaround generically to all Clevo devices with VIA
codecs to cover all in once.
Mikko Ylinen [Mon, 25 Jan 2021 06:39:36 +0000 (08:39 +0200)]
bpf: Drop disabled LSM hooks from the sleepable set
Some networking and keys LSM hooks are conditionally enabled
and when building the new sleepable BPF LSM hooks with those
LSM hooks disabled, the following build error occurs:
BTFIDS vmlinux
FAILED unresolved symbol bpf_lsm_socket_socketpair
To fix the error, conditionally add the relevant networking/keys
LSM hooks to the sleepable set.
Thomas Gleixner [Mon, 18 Jan 2021 18:01:21 +0000 (19:01 +0100)]
futex: Handle faults correctly for PI futexes
fixup_pi_state_owner() tries to ensure that the state of the rtmutex,
pi_state and the user space value related to the PI futex are consistent
before returning to user space. In case that the user space value update
faults and the fault cannot be resolved by faulting the page in via
fault_in_user_writeable() the function returns with -EFAULT and leaves
the rtmutex and pi_state owner state inconsistent.
A subsequent futex_unlock_pi() operates on the inconsistent pi_state and
releases the rtmutex despite not owning it which can corrupt the RB tree of
the rtmutex and cause a subsequent kernel stack use after free.
It was suggested to loop forever in fixup_pi_state_owner() if the fault
cannot be resolved, but that results in runaway tasks which is especially
undesired when the problem happens due to a programming error and not due
to malice.
As the user space value cannot be fixed up, the proper solution is to make
the rtmutex and the pi_state consistent so both have the same owner. This
leaves the user space value out of sync. Any subsequent operation on the
futex will fail because the 10th rule of PI futexes (pi_state owner and
user space value are consistent) has been violated.
As a consequence this removes the inept attempts of 'fixing' the situation
in case that the current task owns the rtmutex when returning with an
unresolvable fault by unlocking the rtmutex which left pi_state::owner and
rtmutex::owner out of sync in a different and only slightly less dangerous
way.
Fixes: 1b7558e457ed ("futexes: fix fault handling in futex_lock_pi") Reported-by: gzobqq@gmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org
Thomas Gleixner [Tue, 19 Jan 2021 14:21:35 +0000 (15:21 +0100)]
futex: Provide and use pi_state_update_owner()
Updating pi_state::owner is done at several places with the same
code. Provide a function for it and use that at the obvious places.
This is also a preparation for a bug fix to avoid yet another copy of the
same code or alternatively introducing a completely unpenetratable mess of
gotos.
Originally-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org
Thomas Gleixner [Tue, 19 Jan 2021 15:06:10 +0000 (16:06 +0100)]
futex: Replace pointless printk in fixup_owner()
If that unexpected case of inconsistent arguments ever happens then the
futex state is left completely inconsistent and the printk is not really
helpful. Replace it with a warning and make the state consistent.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org
Thomas Gleixner [Wed, 20 Jan 2021 15:00:24 +0000 (16:00 +0100)]
futex: Ensure the correct return value from futex_lock_pi()
In case that futex_lock_pi() was aborted by a signal or a timeout and the
task returned without acquiring the rtmutex, but is the designated owner of
the futex due to a concurrent futex_unlock_pi() fixup_owner() is invoked to
establish consistent state. In that case it invokes fixup_pi_state_owner()
which in turn tries to acquire the rtmutex again. If that succeeds then it
does not propagate this success to fixup_owner() and futex_lock_pi()
returns -EINTR or -ETIMEOUT despite having the futex locked.
Return success from fixup_pi_state_owner() in all cases where the current
task owns the rtmutex and therefore the futex and propagate it correctly
through fixup_owner(). Fixup the other callsite which does not expect a
positive return value.
Fixes: c1e2f0eaf015 ("futex: Avoid violating the 10th rule of futex") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org
Johannes Berg [Tue, 26 Jan 2021 10:54:09 +0000 (11:54 +0100)]
staging: rtl8723bs: fix wireless regulatory API misuse
This code ends up calling wiphy_apply_custom_regulatory(), for which
we document that it should be called before wiphy_register(). This
driver doesn't do that, but calls it from ndo_open() with the RTNL
held, which caused deadlocks.
Since the driver just registers static regdomain data and then the
notifier applies the channel changes if any, there's no reason for
it to call this in ndo_open(), move it earlier to fix the deadlock.
Johannes Berg [Fri, 22 Jan 2021 16:11:16 +0000 (17:11 +0100)]
mac80211: pause TX while changing interface type
syzbot reported a crash that happened when changing the interface
type around a lot, and while it might have been easy to fix just
the symptom there, a little deeper investigation found that really
the reason is that we allowed packets to be transmitted while in
the middle of changing the interface type.
Disallow TX by stopping the queues while changing the type.
Johannes Berg [Thu, 21 Jan 2021 16:16:22 +0000 (17:16 +0100)]
wext: fix NULL-ptr-dereference with cfg80211's lack of commit()
Since cfg80211 doesn't implement commit, we never really cared about
that code there (and it's configured out w/o CONFIG_WIRELESS_EXT).
After all, since it has no commit, it shouldn't return -EIWCOMMIT to
indicate commit is needed.
However, EIWCOMMIT is actually an alias for EINPROGRESS, which _can_
happen if e.g. we try to change the frequency but we're already in
the process of connecting to some network, and drivers could return
that value (or even cfg80211 itself might).
This then causes us to crash because dev->wireless_handlers is NULL
but we try to check dev->wireless_handlers->standard[0].
Fix this by also checking dev->wireless_handlers. Also simplify the
code a little bit.
Jason Gerecke [Thu, 21 Jan 2021 18:46:49 +0000 (10:46 -0800)]
HID: wacom: Correct NULL dereference on AES pen proximity
The recent commit to fix a memory leak introduced an inadvertant NULL
pointer dereference. The `wacom_wac->pen_fifo` variable was never
intialized, resuling in a crash whenever functions tried to use it.
Since the FIFO is only used by AES pens (to buffer events from pen
proximity until the hardware reports the pen serial number) this would
have been easily overlooked without testing an AES device.
This patch converts `wacom_wac->pen_fifo` over to a pointer (since the
call to `devres_alloc` allocates memory for us) and ensures that we assign
it to point to the allocated and initalized `pen_fifo` before the function
returns.
Roger Pau Monne [Tue, 19 Jan 2021 10:57:27 +0000 (11:57 +0100)]
xen-blkfront: allow discard-* nodes to be optional
This is inline with the specification described in blkif.h:
* discard-granularity: should be set to the physical block size if
node is not present.
* discard-alignment, discard-secure: should be set to 0 if node not
present.
This was detected as QEMU would only create the discard-granularity
node but not discard-alignment, and thus the setup done in
blkfront_setup_discard would fail.
Fix blkfront_setup_discard to not fail on missing nodes, and also fix
blkif_set_queue_limits to set the discard granularity to the physical
block size if none is specified in xenbus.
Fixes: ed30bf317c5ce ('xen-blkfront: Handle discard requests.') Reported-by: Arthur Borsboom <arthurborsboom@gmail.com> Signed-off-by: Roger Pau Monné <roger.pau@citrix.com> Reviewed-by: Juergen Gross <jgross@suse.com> Tested-By: Arthur Borsboom <arthurborsboom@gmail.com> Link: https://lore.kernel.org/r/20210119105727.95173-1-roger.pau@citrix.com Signed-off-by: Juergen Gross <jgross@suse.com>
Paolo Bonzini [Fri, 8 Jan 2021 16:43:08 +0000 (11:43 -0500)]
KVM: x86: allow KVM_REQ_GET_NESTED_STATE_PAGES outside guest mode for VMX
VMX also uses KVM_REQ_GET_NESTED_STATE_PAGES for the Hyper-V eVMCS,
which may need to be loaded outside guest mode. Therefore we cannot
WARN in that case.
However, that part of nested_get_vmcs12_pages is _not_ needed at
vmentry time. Split it out of KVM_REQ_GET_NESTED_STATE_PAGES handling,
so that both vmentry and migration (and in the latter case, independent
of is_guest_mode) do the parts that are needed.
KVM: x86: Revert "KVM: x86: Mark GPRs dirty when written"
Revert the dirty/available tracking of GPRs now that KVM copies the GPRs
to the GHCB on any post-VMGEXIT VMRUN, even if a GPR is not dirty. Per
commit de3cd117ed2f ("KVM: x86: Omit caching logic for always-available
GPRs"), tracking for GPRs noticeably impacts KVM's code footprint.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210122235049.3107620-3-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: SVM: Unconditionally sync GPRs to GHCB on VMRUN of SEV-ES guest
Drop the per-GPR dirty checks when synchronizing GPRs to the GHCB, the
GRPs' dirty bits are set from time zero and never cleared, i.e. will
always be seen as dirty. The obvious alternative would be to clear
the dirty bits when appropriate, but removing the dirty checks is
desirable as it allows reverting GPR dirty+available tracking, which
adds overhead to all flavors of x86 VMs.
Note, unconditionally writing the GPRs in the GHCB is tacitly allowed
by the GHCB spec, which allows the hypervisor (or guest) to provide
unnecessary info; it's the guest's responsibility to consume only what
it needs (the hypervisor is untrusted after all).
The guest and hypervisor can supply additional state if desired but
must not rely on that additional state being provided.
Cc: Brijesh Singh <brijesh.singh@amd.com> Cc: Tom Lendacky <thomas.lendacky@amd.com> Fixes: 291bd20d5d88 ("KVM: SVM: Add initial support for a VMGEXIT VMEXIT") Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210122235049.3107620-2-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Maxim Levitsky [Thu, 14 Jan 2021 20:54:47 +0000 (22:54 +0200)]
KVM: nVMX: Sync unsync'd vmcs02 state to vmcs12 on migration
Even when we are outside the nested guest, some vmcs02 fields
may not be in sync vs vmcs12. This is intentional, even across
nested VM-exit, because the sync can be delayed until the nested
hypervisor performs a VMCLEAR or a VMREAD/VMWRITE that affects those
rarely accessed fields.
However, during KVM_GET_NESTED_STATE, the vmcs12 has to be up to date to
be able to restore it. To fix that, call copy_vmcs02_to_vmcs12_rare()
before the vmcs12 contents are copied to userspace.
Fixes: 7952d769c29ca ("KVM: nVMX: Sync rarely accessed guest fields only when needed") Reviewed-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20210114205449.8715-2-mlevitsk@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Lorenzo Brescia [Wed, 23 Dec 2020 14:45:07 +0000 (14:45 +0000)]
kvm: tracing: Fix unmatched kvm_entry and kvm_exit events
On VMX, if we exit and then re-enter immediately without leaving
the vmx_vcpu_run() function, the kvm_entry event is not logged.
That means we will see one (or more) kvm_exit, without its (their)
corresponding kvm_entry, as shown here:
It also seems possible for a kvm_entry event to be logged, but then
we leave vmx_vcpu_run() right away (if vmx->emulation_required is
true). In this case, we will have a spurious kvm_entry event in the
trace.
Fix these situations by moving trace_kvm_entry() inside vmx_vcpu_run()
(where trace_kvm_exit() already is).
A trace obtained with this patch applied looks like this:
projects / mirror_ubuntu-kernels.git / log