Key locking simplification removed key->sdata != NULL verification from
ieee80211_key_free(). While that is fine for most use cases, there is one
path where this function can be called with an unlinked key (i.e.,
key->sdata == NULL && key->local == NULL). This results in a NULL pointer
dereference with the current implementation. This is known to happen at
least with FT protocol when wpa_supplicant tries to configure the key
before association.
Avoid the issue by passing in the local pointer to
ieee80211_key_free(). In addition, do not clear the key from hw_accel
or debugfs if it has not yet been added. At least the hw_accel one could
trigger another NULL pointer dereference.
Signed-off-by: Jouni Malinen <j@w1.fi> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00: Write the BSSID to register when interface is added
mananged mode in rt2500pci was broken, due to intf->bssid containing
random data rather then the expected 00:00:00:00:00:00
This is corrected by sending the BSSID to rt2x00lib_config_intf
only in AP mode where the bssid is set to a valid value.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: Don't set per-BSS QoS for monitor interfaces
In AP mode, there is no need to notify the driver about QoS
changes for the monitor interface that is created. The warning
in ieee80211_bss_info_change_notify() would be hit otherwise.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The noisefloor array index always corresponds to the rx chain number it
belongs to (with an offset of 3 for the extension chain).
It's much simpler (and actually more correct) to directly use the
chainmask to calculate the bitmask for the noisefloor array, instead of
using these weird chip revision checks and hardcoded mask values.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 23 Jul 2010 02:07:48 +0000 (04:07 +0200)]
ath9k_hw: fix invalid extension channel noisefloor readings in HT20
When the hardware is configured in HT20 mode, noise floor readings for
the extension channel often return invalid values, which keep the
values in the NF history buffer at the hardware-specific maximum limit.
Fix this by discarding the extension channel values when in HT20 mode.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 23 Jul 2010 01:53:16 +0000 (03:53 +0200)]
ath9k: fix yet another buffer leak in the tx aggregation code
When an aggregation session is being cleaned up, while the tx status
for some frames is being processed, the TID is flushed and its buffers
are sent out.
Unfortunately that left the pending un-acked frames unprocessed, thus
leaking buffers. Fix this by reordering the code so that those frames
are processed first, before the TID is flushed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 22 Jul 2010 15:11:28 +0000 (17:11 +0200)]
mac80211: fix sta assignment
I just had the following:
WARNING: at drivers/net/wireless/iwlwifi/iwl-agn-tx.c:574 iwlagn_tx_skb+0x1576/0x15f0 [iwlagn]()
Call Trace:
<IRQ> [<ffffffff8105c5df>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8105c63a>] warn_slowpath_null+0x1a/0x20
[<ffffffffa0290b46>] iwlagn_tx_skb+0x1576/0x15f0 [iwlagn]
[<ffffffffa027076c>] iwl_mac_tx+0x5c/0x260 [iwlagn]
[<ffffffffa01bdf5b>] __ieee80211_tx+0x10b/0x1a0 [mac80211]
[<ffffffffa01bfb86>] ieee80211_tx_pending+0x186/0x2d0 [mac80211]
[<ffffffff81062ea5>] tasklet_action+0x125/0x130
[<ffffffff810634a6>] __do_softirq+0x106/0x270
[<ffffffff8100c09c>] call_softirq+0x1c/0x30
iwlagn 0000:02:00.0: Attempting to modify non-existing station 107
Note that 107 == 0x6b which is slab poison.
The reason is that mac80211 passed a freed station
pointer to mac80211, because as it happened iwlwifi
reset itself while mac80211 was disconnecting from
the network.
It turns out that we do take care to look up the
station pointer in ieee80211_tx_pending_skb, but
then don't use it, which obviously is a bug. Fix
this by removing the ieee80211_tx_h_sta handler
and assigning the station pointer directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 22 Jul 2010 11:58:51 +0000 (13:58 +0200)]
mac80211: remove bogus rcu_read_lock()
Another remnant of the previous key locking scheme
needs to be removed -- this causes a warning
otherwise as ieee80211_set_default_mgmt_key will
acquire a mutex.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Thu, 22 Jul 2010 08:52:02 +0000 (10:52 +0200)]
ath5k: snprintf() returns largish values
snprintf() returns the number of characters that would have been written
(not counting the NUL character). So we can't use it as the limiter to
simple_read_from_buffer() without capping it first at sizeof(buf).
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Thu, 22 Jul 2010 08:50:28 +0000 (10:50 +0200)]
ath9k: snprintf() returns largish values
The snprintf() function returns the number of characters that would have
been written (not counting the NUL character on the end). It could
potentially be larger than the size of the buffer.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Thu, 22 Jul 2010 19:24:56 +0000 (15:24 -0400)]
iwlwifi: assume vif is NULL for internal scans and non-NULL otherwise
The current practice of checking vif for NULL in one place but not
another seems to confuse some static checkers, smatch in particular.
Since vif will only be NULL in the case of internal scans, adjust the
checks accordingly.
Reported-by: Dan Carpenter <error27@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Thu, 22 Jul 2010 18:45:02 +0000 (14:45 -0400)]
MAINTAINERS: remove entry for wavelan
The driver is already removed from drivers/staging. The wireless
extensions part is not really valid anymore either, since wext got moved
and refactored, etc.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Thu, 22 Jul 2010 18:25:40 +0000 (14:25 -0400)]
MAINTAINERS: mark prism54 obsolete
The prism54 driver had an entry in feature-removal-schedule.txt and it
sees very little activity other than API-change "bombing runs". The
mac80211-based p54 driver should be used instead.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 26 Jul 2010 19:04:12 +0000 (15:04 -0400)]
iwlagn: use __packed on new structure definitions
"iwlagn: add statistic notification structure for WiFi/BT devices" added
several new '__attribute__ ((packed))' lines. Change them to the
generic __packed.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 14 Jul 2010 16:34:50 +0000 (09:34 -0700)]
iwlagn: fix firmware loading TLV error path
gcc complains about the firmware loading:
iwl-agn.c: In function ‘iwlagn_load_firmware’:
iwl-agn.c:1860: warning: ‘tlv_len’ may be used uninitialized in this function
iwl-agn.c:1861: warning: ‘tlv_type’ may be used uninitialized in this function
iwl-agn.c:1862: warning: ‘tlv_data’ may be used uninitialized in this function
This is almost correct but we do do break out of the TLV
parsing loop when setting ret. However, the code is hard
to follow, and clearly even the compiler is having issues
with it too.
Additionally, however, the current code is wrong. If there
is a TLV length check error, the code will report
invalid TLV after parsing: ...
because "len" will still be non-zero as we broke out of
the loop.
So to remove the warning and fix that issue, make the code
easier to read by doing length checking with an error label.
As a result, we can completely remove the "ret" variable.
Also, while at it, remove the "fixed_tlv_size" variable
since each TLV type has its own specified length, it just
happens that we have only variable length, flags (0 length)
and u32 TLVs right now. It should still be checked with more
explicit length checks to make it easier to understand.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Wed, 14 Jul 2010 00:13:15 +0000 (17:13 -0700)]
iwlwifi: add TLV to specify the size of phy calibration table
Different devices have different size of phy calibration table; add
new TLV to specify the size. If the TLV is not part of uCode header, the
default table size will be used to make sure the backward
compatibilities.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Wed, 14 Jul 2010 15:08:05 +0000 (08:08 -0700)]
iwlagn: add .cfg flag to idenfity the need for bt statistics
Only WiFi/BT combo devices need to use bluetooth version of statistics
notification; adding the flag in .cfg file to indicate the need for
using different data structure.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Wed, 21 Jul 2010 09:30:27 +0000 (11:30 +0200)]
mac80211: proper IBSS locking
IBSS has never had locking, instead relying on some
memory barriers etc. That's hard to get right, and
I think we had it wrong too until the previous patch.
Since this is not performance sensitive, it doesn't
make sense to have the maintenance overhead of that,
so add proper locking.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 21 Jul 2010 08:52:40 +0000 (10:52 +0200)]
mac80211: fix IBSS lockdep complaint
Bob reported a lockdep complaint originating in
the mac80211 IBSS code due to the common work
struct patch. The reason is that the IBSS and
station mode code have different locking orders
for the cfg80211 wdev lock and the work struct
(where "locking" implies running/canceling).
Fix this by simply not canceling the work in
the IBSS code, it is not necessary since when
the REQ_RUN bit is cleared, the work will run
without effect if it runs. When the interface
is set down, it is flushed anyway, so there's
no concern about it running after memory has
been invalidated either.
This fixes
https://bugzilla.kernel.org/show_bug.cgi?id=16419
Additionally, looking into this I noticed that
there's a small window while the IBSS is torn
down in which the work may be rescheduled and
the REQ_RUN bit be set again after leave() has
cleared it when a scan finishes at exactly the
same time. Avoid that by setting the ssid_len
to zero before clearing REQ_RUN which signals
to the scan finish code that this interface is
not active.
Reported-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Maxime Bizon [Wed, 21 Jul 2010 15:21:38 +0000 (17:21 +0200)]
cfg80211: fix race between sysfs and cfg80211
device_add() is called before adding the phy to the cfg80211 device
list.
So if a userspace program uses sysfs uevents to detect new phy
devices, and queries nl80211 to get phy info, it can get ENODEV even
though the phy exists in sysfs.
An easy workaround is to hold the cfg80211 mutex until the phy is
present in sysfs/cfg80211/debugfs.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 21 Jul 2010 15:37:19 +0000 (11:37 -0400)]
b43: silence most sparse warnings
CHECK drivers/net/wireless/b43/main.c
drivers/net/wireless/b43/main.c:111:5: warning: symbol 'b43_modparam_pio' was not declared. Should it be static?
CHECK drivers/net/wireless/b43/phy_g.c
drivers/net/wireless/b43/phy_g.c:975:56: warning: cast truncates bits from constant value (ffff7fff becomes 7fff)
CHECK drivers/net/wireless/b43/phy_lp.c
drivers/net/wireless/b43/phy_lp.c:2701:6: warning: symbol 'b43_lpphy_op_switch_analog' was not declared. Should it be static?
drivers/net/wireless/b43/phy_lp.c:1148:30: warning: cast truncates bits from constant value (ffff1fff becomes 1fff)
drivers/net/wireless/b43/phy_lp.c:1525:30: warning: cast truncates bits from constant value (ffff1fff becomes 1fff)
drivers/net/wireless/b43/phy_lp.c:1529:30: warning: cast truncates bits from constant value (ffff1fff becomes 1fff)
CHECK drivers/net/wireless/b43/wa.c
drivers/net/wireless/b43/wa.c:385:60: warning: cast truncates bits from constant value (ffff00ff becomes ff)
drivers/net/wireless/b43/wa.c:403:55: warning: cast truncates bits from constant value (ffff00ff becomes ff)
drivers/net/wireless/b43/wa.c:405:55: warning: cast truncates bits from constant value (ffff00ff becomes ff)
drivers/net/wireless/b43/wa.c:415:71: warning: cast truncates bits from constant value (ffff0fff becomes fff)
AFAICT, none of these amount to real bugs. But this reduces warning
spam from sparse w/o significantly affecting readability of the code (IMHO).
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To make net/ and include/net/ code consistent use __packed instead of
__attribute__ ((packed)). Bluetooth subsystem was one of the last net
subsys still using __attribute__ ((packed)).
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Mon, 12 Jul 2010 14:37:04 +0000 (11:37 -0300)]
Bluetooth: Add HCIUARTSETFLAGS and HCIUARTGETFLAGS ioctls
This patch introduces two new ioctls: HCIUARTSETFLAGS and
HCIUARTGETFLAGS. The only flag available for now is HCI_UART_RAW_DEVICE
which allows to initialize a UART device into RAW mode from userspace.
This is particularly useful for experimenting with Bluetooth controllers
that don't yet have proper support in BlueZ.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Send ConfigReq after send a ConnectionRsp
The extended L2CAP features requires that one should initiate a
ConfigReq after send the ConnectionRsp. This patch changes the behaviour
of the configuration process of our stack.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Fix error return on L2CAP-HCI interface.
L2CAP only deals with ACL links. EINVAL should be returned otherwise.
Signed-off-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Acked-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Acked-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Fix error return for l2cap_connect_rsp().
Signed-off-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Acked-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the socket is in a bad state EBADFD is more appropriate then EINVAL.
Signed-off-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Acked-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we try to send a message bigger than the outgoing MTU value
EMSGSIZE (message too long) should be returned.
Signed-off-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Acked-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
It doesn't make sense to have a return value since we always set it
to 0.
Signed-off-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Acked-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Return a proper error value if socket is already connected.
Signed-off-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Acked-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now we also check if can push skb userspace just after receive a new
skb instead of only wait the l2cap_busy_work wake up from time to time
to check the local busy condition.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
backlog queue is the canonical mechanism to avoid race conditions due
interrupts in bottom half context. After the socket lock is released the
net core take care of push all skb in its backlog queue.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Remove the send_lock spinlock from ERTM
Using a lock to deal with the ERTM race condition - interruption with
new data from the hci layer - is wrong. We should use the native skb
backlog queue.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Change the way we set ERTM mode as mandatory
If the socket type is SOCK_STREAM we set Enhanced Retransmisson Mode or
Streaming Mode as mandatory. That means that we will close the channel
if the other side doesn't support or request the the mandatory mode.
Basic mode can't be set as mandatory.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Tweaks to l2cap_send_i_or_rr_or_rnr() flow
l2cap_send_sframe() already set the F-bit if we set L2CAP_CONN_SEND_FBIT
and unset L2CAP_CONN_SEND_FBIT after send the F-bit.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Fix ERTM error reporting to the userspace
If any error occurs during transfers we have to tell userspace that
something wrong happened.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Fix missing retransmission action with RR(P=1)
The Bluetooth SIG Profile Tuning Suite Software uses the CSA1 spec
to run the L2CAP tests. The new 3.0 spec has a missing
Retransmit-I-Frames action when the Remote side is Busy.
We still start the retransmission timer if Remote is Busy and unacked
frames > 0. We do everything we did before this change plus the
Retransmission of I-frames.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We have to check if the proposed tx_window value is not greater that
maximum value supported.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
ERTM spec mandates that after receive a P-bit we shall send an F-bit in
response. This patch fixes this for retransmitted packets, on
retransmitting we were missing to check for a pending F-bit to be sent.
Also we were missing some annotation to send a F-bit.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Stop ack_timer if ERTM enters in Local Busy or SREJ_SENT
The ack_timer is implemation specific, disabling it in such situation
avoids some potencial errors in the ERTM protocol.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Amitkumar Karwar [Thu, 27 May 2010 23:38:37 +0000 (16:38 -0700)]
Bluetooth: Process interrupt in main thread of btmrvl driver as well
When driver is sending a command or data and the firmware is also
sending a sleep event, sometimes it is observed that driver will
continue to send the command/data to firmware right after processing
sleep event. Once sleep event is processed driver is not supposed to
send anything because firmware is in sleep state after that. Previously
interrupt processing was done in SDIO interrupt callback handler.
Now it is done in btmrvl driver main thread to solve the
cross-sending properly.
Ron Shaffer [Fri, 28 May 2010 15:53:46 +0000 (11:53 -0400)]
Bluetooth: Reassigned copyright to Code Aurora Forum
Qualcomm, Inc. has reassigned rights to Code Aurora Forum. Accordingly,
as files are modified by Code Aurora Forum members, the copyright
statement will be updated.
Signed-off-by: Ron Shaffer <rshaffer@codeaurora.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Fix warning: variable 'tty' set but not used
The patch below fixes a warning message when using gcc 4.6.0.
CC [M] drivers/bluetooth/hci_ldisc.o
drivers/bluetooth/hci_ldisc.c: In function 'hci_uart_send_frame':
drivers/bluetooth/hci_ldisc.c:213:21: warning: variable 'tty' set but not used
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com> Reviewed-By: Gustavo F. Padovan <gustavo@padovan.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
projects / mirror_ubuntu-kernels.git / log