Aya Levin [Thu, 7 Jan 2021 13:50:18 +0000 (15:50 +0200)]
net: ipv6: Validate GSO SKB before finish IPv6 processing
There are cases where GSO segment's length exceeds the egress MTU:
- Forwarding of a TCP GRO skb, when DF flag is not set.
- Forwarding of an skb that arrived on a virtualisation interface
(virtio-net/vhost/tap) with TSO/GSO size set by other network
stack.
- Local GSO skb transmitted on an NETIF_F_TSO tunnel stacked over an
interface with a smaller MTU.
- Arriving GRO skb (or GSO skb in a virtualised environment) that is
bridged to a NETIF_F_TSO tunnel stacked over an interface with an
insufficient MTU.
If so:
- Consume the SKB and its segments.
- Issue an ICMP packet with 'Packet Too Big' message containing the
MTU, allowing the source host to reduce its Path MTU appropriately.
Note: These cases are handled in the same manner in IPv4 output finish.
This patch aligns the behavior of IPv6 and the one of IPv4.
Fixes: 9e50849054a4 ("netfilter: ipv6: move POSTROUTING invocation before fragmentation") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Link: https://lore.kernel.org/r/1610027418-30438-1-git-send-email-ayal@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Manish Chopra [Thu, 7 Jan 2021 10:15:20 +0000 (02:15 -0800)]
netxen_nic: fix MSI/MSI-x interrupts
For all PCI functions on the netxen_nic adapter, interrupt
mode (INTx or MSI) configuration is dependent on what has
been configured by the PCI function zero in the shared
interrupt register, as these adapters do not support mixed
mode interrupts among the functions of a given adapter.
Logic for setting MSI/MSI-x interrupt mode in the shared interrupt
register based on PCI function id zero check is not appropriate for
all family of netxen adapters, as for some of the netxen family
adapters PCI function zero is not really meant to be probed/loaded
in the host but rather just act as a management function on the device,
which caused all the other PCI functions on the adapter to always use
legacy interrupt (INTx) mode instead of choosing MSI/MSI-x interrupt mode.
This patch replaces that check with port number so that for all
type of adapters driver attempts for MSI/MSI-x interrupt modes.
====================
net: fix issues around register_netdevice() failures
This series attempts to clean up the life cycle of struct
net_device. Dave has added dev->needs_free_netdev in the
past to fix double frees, we can lean on that mechanism
a little more to fix remaining issues with register_netdevice().
This is the next chapter of the saga which already includes:
commit 0e0eee2465df ("net: correct error path in rtnl_newlink()")
commit e51fb152318e ("rtnetlink: fix a memory leak when ->newlink fails")
commit cf124db566e6 ("net: Fix inconsistent teardown and release of private netdev state.")
commit 93ee31f14f6f ("[NET]: Fix free_netdev on register_netdev failure.")
commit 814152a89ed5 ("net: fix memleak in register_netdevice()")
commit 10cc514f451a ("net: Fix null de-reference of device refcount")
The immediate problem which gets fixed here is that calling
free_netdev() right after unregister_netdevice() is illegal
because we need to release rtnl_lock first, to let the
unregistration finish. Note that unregister_netdevice() is
just a wrapper of unregister_netdevice_queue(), it only
does half of the job.
Where this limitation becomes most problematic is in failure
modes of register_netdevice(). There is a notifier call right
at the end of it, which lets other subsystems veto the entire
thing. At which point we should really go through a full
unregister_netdevice(), but we can't because callers may
go straight to free_netdev() after the failure, and that's
no bueno (see the previous paragraph).
This set makes free_netdev() more lenient, when device
is still being unregistered free_netdev() will simply set
dev->needs_free_netdev and let the unregister process do
the freeing.
With the free_netdev() problem out of the way failures in
register_netdevice() can make use of net_todo, again.
Users are still expected to call free_netdev() right after
failure but that will only set dev->needs_free_netdev.
To prevent the pathological case of:
dev->needs_free_netdev = true;
if (register_netdevice(dev)) {
rtnl_unlock();
free_netdev(dev);
}
make register_netdevice()'s failure clear dev->needs_free_netdev.
Problems described above are only present with register_netdevice() /
unregister_netdevice(). We have two parallel APIs for registration
of devices:
- those called outside rtnl_lock (register_netdev(), and
unregister_netdev());
- and those to be used under rtnl_lock - register_netdevice()
and unregister_netdevice().
The former is trivial and has no problems. The alternative
approach to fix the latter would be to also separate the
freeing functions - i.e. add free_netdevice(). This has been
implemented (incl. converting all relevant calls in the tree)
but it feels a little unnecessary to put the burden of choosing
the right free_netdev{,ice}() call on the programmer when we
can "just do the right thing" by default.
====================
Jakub Kicinski [Wed, 6 Jan 2021 18:40:07 +0000 (10:40 -0800)]
net: make sure devices go through netdev_wait_all_refs
If register_netdevice() fails at the very last stage - the
notifier call - some subsystems may have already seen it and
grabbed a reference. struct net_device can't be freed right
away without calling netdev_wait_all_refs().
Now that we have a clean interface in form of dev->needs_free_netdev
and lenient free_netdev() we can undo what commit 93ee31f14f6f ("[NET]:
Fix free_netdev on register_netdev failure.") has done and complete
the unregistration path by bringing the net_set_todo() call back.
After registration fails user is still expected to explicitly
free the net_device, so make sure ->needs_free_netdev is cleared,
otherwise rolling back the registration will cause the old double
free for callers who release rtnl_lock before the free.
This also solves the problem of priv_destructor not being called
on notifier error.
net_set_todo() will be moved back into unregister_netdevice_queue()
in a follow up.
Reported-by: Hulk Robot <hulkci@huawei.com> Reported-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 6 Jan 2021 18:40:06 +0000 (10:40 -0800)]
net: make free_netdev() more lenient with unregistering devices
There are two flavors of handling netdev registration:
- ones called without holding rtnl_lock: register_netdev() and
unregister_netdev(); and
- those called with rtnl_lock held: register_netdevice() and
unregister_netdevice().
While the semantics of the former are pretty clear, the same can't
be said about the latter. The netdev_todo mechanism is utilized to
perform some of the device unregistering tasks and it hooks into
rtnl_unlock() so the locked variants can't actually finish the work.
In general free_netdev() does not mix well with locked calls. Most
drivers operating under rtnl_lock set dev->needs_free_netdev to true
and expect core to make the free_netdev() call some time later.
The part where this becomes most problematic is error paths. There is
no way to unwind the state cleanly after a call to register_netdevice(),
since unreg can't be performed fully without dropping locks.
Make free_netdev() more lenient, and defer the freeing if device
is being unregistered. This allows error paths to simply call
free_netdev() both after register_netdevice() failed, and after
a call to unregister_netdevice() but before dropping rtnl_lock.
Simplify the error paths which are currently doing gymnastics
around free_netdev() handling.
Tom Parkin [Thu, 7 Jan 2021 18:13:15 +0000 (18:13 +0000)]
ppp: fix refcount underflow on channel unbridge
When setting up a channel bridge, ppp_bridge_channels sets the
pch->bridge field before taking the associated reference on the bridge
file instance.
This opens up a refcount underflow bug if ppp_bridge_channels called
via. iotcl runs concurrently with ppp_unbridge_channels executing via.
file release.
The bug is triggered by ppp_bridge_channels taking the error path
through the 'err_unset' label. In this scenario, pch->bridge is set,
but the reference on the bridged channel will not be taken because
the function errors out. If ppp_unbridge_channels observes pch->bridge
before it is unset by the error path, it will erroneously drop the
reference on the bridged channel and cause a refcount underflow.
To avoid this, ensure that ppp_bridge_channels holds a reference on
each channel in advance of setting the bridge pointers.
Signed-off-by: Tom Parkin <tparkin@katalix.com> Fixes: 4cf476ced45d ("ppp: add PPPIOCBRIDGECHAN and PPPIOCUNBRIDGECHAN ioctls") Acked-by: Guillaume Nault <gnault@redhat.com> Link: https://lore.kernel.org/r/20210107181315.3128-1-tparkin@katalix.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Baptiste Lepers [Thu, 7 Jan 2021 05:11:10 +0000 (16:11 +1100)]
udp: Prevent reuseport_select_sock from reading uninitialized socks
reuse->socks[] is modified concurrently by reuseport_add_sock. To
prevent reading values that have not been fully initialized, only read
the array up until the last known safe index instead of incorrectly
re-reading the last index of the array.
Fixes: acdcecc61285f ("udp: correct reuseport selection with connected sockets") Signed-off-by: Baptiste Lepers <baptiste.lepers@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/20210107051110.12247-1-baptiste.lepers@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dongseok Yi [Fri, 8 Jan 2021 02:28:38 +0000 (11:28 +0900)]
net: fix use-after-free when UDP GRO with shared fraglist
skbs in fraglist could be shared by a BPF filter loaded at TC. If TC
writes, it will call skb_ensure_writable -> pskb_expand_head to create
a private linear section for the head_skb. And then call
skb_clone_fraglist -> skb_get on each skb in the fraglist.
skb_segment_list overwrites part of the skb linear section of each
fragment itself. Even after skb_clone, the frag_skbs share their
linear section with their clone in PF_PACKET.
Both sk_receive_queue of PF_PACKET and PF_INET (or PF_INET6) can have
a link for the same frag_skbs chain. If a new skb (not frags) is
queued to one of the sk_receive_queue, multiple ptypes can see and
release this. It causes use-after-free.
Fixes: 3a1296a38d0c (net: Support GRO/GSO fraglist chaining.) Signed-off-by: Dongseok Yi <dseok.yi@samsung.com> Acked-by: Willem de Bruijn <willemb@google.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/r/1610072918-174177-1-git-send-email-dseok.yi@samsung.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stephan Gerhold [Wed, 6 Jan 2021 10:07:55 +0000 (11:07 +0100)]
net: ipa: modem: add missing SET_NETDEV_DEV() for proper sysfs links
At the moment it is quite hard to identify the network interface
provided by IPA in userspace components: The network interface is
created as virtual device, without any link to the IPA device.
The interface name ("rmnet_ipa%d") is the only indication that the
network interface belongs to IPA, but this is not very reliable.
Add SET_NETDEV_DEV() to associate the network interface with the
IPA parent device. This allows userspace services like ModemManager
to properly identify that this network interface is provided by IPA
and belongs to the modem.
Cc: Alex Elder <elder@kernel.org> Fixes: a646d6ec9098 ("soc: qcom: ipa: modem and microcontroller") Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Link: https://lore.kernel.org/r/20210106100755.56800-1-stephan@gerhold.net Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Fri, 8 Jan 2021 20:12:30 +0000 (12:12 -0800)]
Merge tag 'net-5.11-rc3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull more networking fixes from Jakub Kicinski:
"Slightly lighter pull request to get back into the Thursday cadence.
Current release - always broken:
- can: mcp251xfd: fix Tx/Rx ring buffer driver race conditions
- dsa: hellcreek: fix led_classdev build errors
Previous releases - regressions:
- ipv6: fib: flush exceptions when purging route to avoid netdev
reference leak
- ip_tunnels: fix pmtu check in nopmtudisc mode
- ip: always refragment ip defragmented packets to avoid MTU issues
when forwarding through tunnels, correct "packet too big" message
is prohibitively tricky to generate
- s390/qeth: fix locking for discipline setup / removal and during
recovery to prevent both deadlocks and races
- mlx5: Use port_num 1 instead of 0 when delete a RoCE address
Previous releases - always broken:
- cdc_ncm: correct overhead calculation in delayed_ndp_size to
prevent out of bound accesses with Huawei 909s-120 LTE module
- fix stmmac dwmac-sun8i suspend/resume:
- PHY being left powered off
- MAC syscon configuration being reset
- reference to the reset controller being improperly dropped
- qrtr: fix null-ptr-deref in qrtr_ns_remove
- can: tcan4x5x: fix bittiming const, use common bittiming from m_can
driver
- mlx5e: CT: Use per flow counter when CT flow accounting is enabled
- mlx5e: Fix SWP offsets when vlan inserted by driver
Misc:
- bpf: Fix a task_iter bug caused by a bpf -> net merge conflict
resolution
And the usual many fixes to various error paths"
* tag 'net-5.11-rc3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (69 commits)
net: dsa: lantiq_gswip: Exclude RMII from modes that report 1 GbE
s390/qeth: fix L2 header access in qeth_l3_osa_features_check()
s390/qeth: fix locking for discipline setup / removal
s390/qeth: fix deadlock during recovery
selftests: fib_nexthops: Fix wrong mausezahn invocation
nexthop: Bounce NHA_GATEWAY in FDB nexthop groups
nexthop: Unlink nexthop group entry in error path
nexthop: Fix off-by-one error in error path
octeontx2-af: fix memory leak of lmac and lmac->name
chtls: Fix chtls resources release sequence
chtls: Added a check to avoid NULL pointer dereference
chtls: Replace skb_dequeue with skb_peek
chtls: Avoid unnecessary freeing of oreq pointer
chtls: Fix panic when route to peer not configured
chtls: Remove invalid set_tcb call
chtls: Fix hardware tid leak
net: ip: always refragment ip defragmented packets
net: fix pmtu check in nopmtudisc mode
selftests: netfilter: add selftest for ipip pmtu discovery with enabled connection tracking
docs: octeontx2: tune rst markup
...
Linus Torvalds [Thu, 7 Jan 2021 17:43:54 +0000 (09:43 -0800)]
poll: fix performance regression due to out-of-line __put_user()
The kernel test robot reported a -5.8% performance regression on the
"poll2" test of will-it-scale, and bisected it to commit d55564cfc222
("x86: Make __put_user() generate an out-of-line call").
I didn't expect an out-of-line __put_user() to matter, because no normal
core code should use that non-checking legacy version of user access any
more. But I had overlooked the very odd poll() usage, which does a
__put_user() to update the 'revents' values of the poll array.
Now, Al Viro correctly points out that instead of updating just the
'revents' field, it would be much simpler to just copy the _whole_
pollfd entry, and then we could just use "copy_to_user()" on the whole
array of entries, the same way we use "copy_from_user()" a few lines
earlier to get the original values.
But that is not what we've traditionally done, and I worry that threaded
applications might be concurrently modifying the other fields of the
pollfd array. So while Al's suggestion is simpler - and perhaps worth
trying in the future - this instead keeps the "just update revents"
model.
To fix the performance regression, use the modern "unsafe_put_user()"
instead of __put_user(), with the proper "user_write_access_begin()"
guarding in place. This improves code generation enormously.
Link: https://lore.kernel.org/lkml/20210107134723.GA28532@xsang-OptiPlex-9020/ Reported-by: kernel test robot <oliver.sang@intel.com> Tested-by: Oliver Sang <oliver.sang@intel.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: David Laight <David.Laight@aculab.com> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The commit caused that ttynull was used as the default console
on several systems[1][2][3]. As a result, the console was
blank even when a better alternative existed.
It happened when there was no console configured
on the command line and ttynull_init() was the first initcall
calling register_console().
Or it happened when /dev/ did not exist when console_on_rootfs()
was called. It was not able to open /dev/console even though
a console driver was registered. It tried to add ttynull console
but it obviously did not help. But ttynull became the preferred
console and was used by /dev/console when it was available later.
The commit tried to fix a historical problem that have been there
for ages. The primary motivation was the commit 3cffa06aeef7ece30f6
("printk/console: Allow to disable console output by using console=""
or console=null"). It provided a clean solution for a workaround
that was widely used and worked only by chance.
This revert causes that the console="" or console=null command line
options will again work only by chance. These options will cause that
a particular console will be preferred and the default (tty) ones
will not get enabled. There will be no console registered at
all. As a result there won't be stdin, stdout, and stderr for
the init process. But it worked exactly this way even before.
The proper solution has to fulfill many conditions:
+ Register ttynull only when explicitly required or as
the ultimate fallback.
+ ttynull should get associated with /dev/console but it must
not become preferred console when used as a fallback.
Especially, it must still be possible to replace it
by a better console later.
Such a change requires clean up of the register_console() code.
Otherwise, it would be even harder to follow. Especially, the use
of has_preferred_console and CON_CONSDEV flag is tricky. The clean
up is risky. The ordering of consoles is not well defined. And
any changes tend to break existing user settings.
Do the revert at the least risky solution for now.
Jakub Kicinski [Fri, 8 Jan 2021 03:13:29 +0000 (19:13 -0800)]
Merge tag 'mlx5-fixes-2021-01-07' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2021-01-07
* tag 'mlx5-fixes-2021-01-07' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Fix memleak in mlx5e_create_l2_table_groups
net/mlx5e: Fix two double free cases
net/mlx5: Release devlink object if adev fails
net/mlx5e: ethtool, Fix restriction of autoneg with 56G
net/mlx5e: In skb build skip setting mark in switchdev mode
net/mlx5: E-Switch, fix changing vf VLANID
net/mlx5e: Fix SWP offsets when vlan inserted by driver
net/mlx5e: CT: Use per flow counter when CT flow accounting is enabled
net/mlx5: Use port_num 1 instead of 0 when delete a RoCE address
net/mlx5e: Add missing capability check for uplink follow
net/mlx5: Check if lag is supported before creating one
====================
Jakub Kicinski [Fri, 8 Jan 2021 02:54:08 +0000 (18:54 -0800)]
Merge branch 's390-qeth-fixes-2021-01-07'
Julian Wiedmann says:
====================
s390/qeth: fixes 2021-01-07
This brings two locking fixes for the device control path.
Also one fix for a path where our .ndo_features_check() attempts to
access a non-existent L2 header.
====================
Julian Wiedmann [Thu, 7 Jan 2021 17:24:42 +0000 (18:24 +0100)]
s390/qeth: fix L2 header access in qeth_l3_osa_features_check()
ip_finish_output_gso() may call .ndo_features_check() even before the
skb has a L2 header. This conflicts with qeth_get_ip_version()'s attempt
to inspect the L2 header via vlan_eth_hdr().
Switch to vlan_get_protocol(), as already used further down in the
common qeth_features_check() path.
Fixes: f13ade199391 ("s390/qeth: run non-offload L3 traffic over common xmit path") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Julian Wiedmann [Thu, 7 Jan 2021 17:24:41 +0000 (18:24 +0100)]
s390/qeth: fix locking for discipline setup / removal
Due to insufficient locking, qeth_core_set_online() and
qeth_dev_layer2_store() can run in parallel, both attempting to load &
setup the discipline (and stepping on each other toes along the way).
A similar race can also occur between qeth_core_remove_device() and
qeth_dev_layer2_store().
Access to .discipline is meant to be protected by the discipline_mutex,
so add/expand the locking in qeth_core_remove_device() and
qeth_core_set_online().
Adjust the locking in qeth_l*_remove_device() accordingly, as it's now
handled by the callers in a consistent manner.
Based on an initial patch by Ursula Braun.
Fixes: 9dc48ccc68b9 ("qeth: serialize sysfs-triggered device configurations") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Julian Wiedmann [Thu, 7 Jan 2021 17:24:40 +0000 (18:24 +0100)]
s390/qeth: fix deadlock during recovery
When qeth_dev_layer2_store() - holding the discipline_mutex - waits
inside qeth_l*_remove_device() for a qeth_do_reset() thread to complete,
we can hit a deadlock if qeth_do_reset() concurrently calls
qeth_set_online() and thus tries to aquire the discipline_mutex.
Move the discipline_mutex locking outside of qeth_set_online() and
qeth_set_offline(), and turn the discipline into a parameter so that
callers understand the dependency.
To fix the deadlock, we can now relax the locking:
As already established, qeth_l*_remove_device() waits for
qeth_do_reset() to complete. So qeth_do_reset() itself is under no risk
of having card->discipline ripped out while it's running, and thus
doesn't need to take the discipline_mutex.
Fixes: 9dc48ccc68b9 ("qeth: serialize sysfs-triggered device configurations") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 8 Jan 2021 02:47:21 +0000 (18:47 -0800)]
Merge branch 'nexthop-various-fixes'
Ido Schimmel says:
====================
nexthop: Various fixes
This series contains various fixes for the nexthop code. The bugs were
uncovered during the development of resilient nexthop groups.
Patches #1-#2 fix the error path of nexthop_create_group(). I was not
able to trigger these bugs with current code, but it is possible with
the upcoming resilient nexthop groups code which adds a user
controllable memory allocation further in the function.
Patch #3 fixes wrong validation of netlink attributes.
Patch #4 fixes wrong invocation of mausezahn in a selftest.
====================
For IPv6 traffic, mausezahn needs to be invoked with '-6'. Otherwise an
error is returned:
# ip netns exec me mausezahn veth1 -B 2001:db8:101::2 -A 2001:db8:91::1 -c 0 -t tcp "dp=1-1023, flags=syn"
Failed to set source IPv4 address. Please check if source is set to a valid IPv4 address.
Invalid command line parameters!
Fixes: 7c741868ceab ("selftests: Add torture tests to nexthop tests") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Petr Machata [Thu, 7 Jan 2021 14:48:23 +0000 (16:48 +0200)]
nexthop: Bounce NHA_GATEWAY in FDB nexthop groups
The function nh_check_attr_group() is called to validate nexthop groups.
The intention of that code seems to have been to bounce all attributes
above NHA_GROUP_TYPE except for NHA_FDB. However instead it bounces all
these attributes except when NHA_FDB attribute is present--then it accepts
them.
NHA_FDB validation that takes place before, in rtm_to_nh_config(), already
bounces NHA_OIF, NHA_BLACKHOLE, NHA_ENCAP and NHA_ENCAP_TYPE. Yet further
back, NHA_GROUPS and NHA_MASTER are bounced unconditionally.
But that still leaves NHA_GATEWAY as an attribute that would be accepted in
FDB nexthop groups (with no meaning), so long as it keeps the address
family as unspecified:
# ip nexthop add id 1 fdb via 127.0.0.1
# ip nexthop add id 10 fdb via default group 1
The nexthop code is still relatively new and likely not used very broadly,
and the FDB bits are newer still. Even though there is a reproducer out
there, it relies on an improbable gateway arguments "via default", "via
all" or "via any". Given all this, I believe it is OK to reformulate the
condition to do the right thing and bounce NHA_GATEWAY.
Fixes: 38428d68719c ("nexthop: support for fdb ecmp nexthops") Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ido Schimmel [Thu, 7 Jan 2021 14:48:22 +0000 (16:48 +0200)]
nexthop: Unlink nexthop group entry in error path
In case of error, remove the nexthop group entry from the list to which
it was previously added.
Fixes: 430a049190de ("nexthop: Add support for nexthop groups") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ido Schimmel [Thu, 7 Jan 2021 14:48:21 +0000 (16:48 +0200)]
nexthop: Fix off-by-one error in error path
A reference was not taken for the current nexthop entry, so do not try
to put it in the error path.
Fixes: 430a049190de ("nexthop: Add support for nexthop groups") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Colin Ian King [Thu, 7 Jan 2021 12:39:16 +0000 (12:39 +0000)]
octeontx2-af: fix memory leak of lmac and lmac->name
Currently the error return paths don't kfree lmac and lmac->name
leading to some memory leaks. Fix this by adding two error return
paths that kfree these objects
Addresses-Coverity: ("Resource leak") Fixes: 1463f382f58d ("octeontx2-af: Add support for CGX link management") Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20210107123916.189748-1-colin.king@canonical.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ayush Sawal [Wed, 6 Jan 2021 04:29:12 +0000 (09:59 +0530)]
chtls: Fix chtls resources release sequence
CPL_ABORT_RPL is sent after releasing the resources by calling
chtls_release_resources(sk); and chtls_conn_done(sk);
eventually causing kernel panic. Fixing it by calling release
in appropriate order.
Ayush Sawal [Wed, 6 Jan 2021 04:29:10 +0000 (09:59 +0530)]
chtls: Replace skb_dequeue with skb_peek
The skb is unlinked twice, one in __skb_dequeue in function
chtls_reset_synq() and another in cleanup_syn_rcv_conn().
So in this patch using skb_peek() instead of __skb_dequeue(),
so that unlink will be handled only in cleanup_syn_rcv_conn().
Ayush Sawal [Wed, 6 Jan 2021 04:29:07 +0000 (09:59 +0530)]
chtls: Remove invalid set_tcb call
At the time of SYN_RECV, connection information is not
initialized at FW, updating tcb flag over uninitialized
connection causes adapter crash. We don't need to
update the flag during SYN_RECV state, so avoid this.
Ayush Sawal [Wed, 6 Jan 2021 04:29:06 +0000 (09:59 +0530)]
chtls: Fix hardware tid leak
send_abort_rpl() is not calculating cpl_abort_req_rss offset and
ends up sending wrong TID with abort_rpl WR causng tid leaks.
Replaced send_abort_rpl() with chtls_send_abort_rpl() as it is
redundant.
We've added 4 non-merge commits during the last 10 day(s) which contain
a total of 4 files changed, 14 insertions(+), 7 deletions(-).
The main changes are:
1) Fix task_iter bug caused by the merge conflict resolution, from Yonghong.
2) Fix resolve_btfids for multiple type hierarchies, from Jiri.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpftool: Fix compilation failure for net.o with older glibc
tools/resolve_btfids: Warn when having multiple IDs for single type
bpf: Fix a task_iter bug caused by a merge conflict resolution
selftests/bpf: Fix a compile error for BPF_F_BPRM_SECUREEXEC
====================
Christian Perle reported a PMTU blackhole due to unexpected interaction
between the ip defragmentation that comes with connection tracking and
ip tunnels.
Unfortunately setting 'nopmtudisc' on the tunnel breaks the test
scenario even without netfilter.
MTU is 1500 everywhere, except on Router A to Wanrouter and
Wanrouter to Router B.
Router A and Router B use IPIP tunnel interfaces to tunnel traffic
between Client A and Client B over WAN.
Client A sends a 1400 byte UDP datagram to Client B.
This packet gets encapsulated in the IPIP tunnel.
This works, packet is received on client B.
When conntrack (or anything else that forces ip defragmentation) is
enabled on Router A, the packet gets dropped on Router A after
encapsulation because they exceed the link MTU.
Setting the 'nopmtudisc' flag on the IPIP tunnel makes things worse,
no packets pass even in the no-netfilter scenario.
Patch one is a reproducer script for selftest infra.
Patch two is a fix for 'nopmtudisc' behaviour so ip_tunnel will send
an icmp error to Client A. This allows 'nopmtudisc' tunnel to forward
the UDP datagrams.
Patch three enables ip refragmentation for all reassembled packets, just
like ipv6.
====================
net: ip: always refragment ip defragmented packets
Conntrack reassembly records the largest fragment size seen in IPCB.
However, when this gets forwarded/transmitted, fragmentation will only
be forced if one of the fragmented packets had the DF bit set.
In that case, a flag in IPCB will force fragmentation even if the
MTU is large enough.
This should work fine, but this breaks with ip tunnels.
Consider client that sends a UDP datagram of size X to another host.
The client fragments the datagram, so two packets, of size y and z, are
sent. DF bit is not set on any of these packets.
Middlebox netfilter reassembles those packets back to single size-X
packet, before routing decision.
packet-size-vs-mtu checks in ip_forward are irrelevant, because DF bit
isn't set. At output time, ip refragmentation is skipped as well
because x is still smaller than the mtu of the output device.
If ttransmit device is an ip tunnel, the packet size increases to
x+overhead.
Also, tunnel might be configured to force DF bit on outer header.
In this case, packet will be dropped (exceeds MTU) and an ICMP error is
generated back to sender.
But sender already respects the announced MTU, all the packets that
it sent did fit the announced mtu.
Force refragmentation as per original sizes unconditionally so ip tunnel
will encapsulate the fragments instead.
The only other solution I see is to place ip refragmentation in
the ip_tunnel code to handle this case.
Fixes: d6b915e29f4ad ("ip_fragment: don't forward defragmented DF packet") Reported-by: Christian Perle <christian.perle@secunet.com> Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For some reason ip_tunnel insist on setting the DF bit anyway when the
inner header has the DF bit set, EVEN if the tunnel was configured with
'nopmtudisc'.
This means that the script added in the previous commit
cannot be made to work by adding the 'nopmtudisc' flag to the
ip tunnel configuration. Doing so breaks connectivity even for the
without-conntrack/netfilter scenario.
When nopmtudisc is set, the tunnel will skip the mtu check, so no
icmp error is sent to client. Then, because inner header has DF set,
the outer header gets added with DF bit set as well.
IP stack then sends an error to itself because the packet exceeds
the device MTU.
Fixes: 23a3647bc4f93 ("ip_tunnels: Use skb-len to PMTU check.") Cc: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lukas Bulwahn [Wed, 6 Jan 2021 16:17:35 +0000 (17:17 +0100)]
docs: octeontx2: tune rst markup
Commit 80b9414832a1 ("docs: octeontx2: Add Documentation for NPA health
reporters") added new documentation with improper formatting for rst, and
caused a few new warnings for make htmldocs in octeontx2.rst:169--202.
Tune markup and formatting for better presentation in the HTML view.
Dinghao Liu [Mon, 21 Dec 2020 11:27:31 +0000 (19:27 +0800)]
net/mlx5e: Fix memleak in mlx5e_create_l2_table_groups
When mlx5_create_flow_group() fails, ft->g should be
freed just like when kvzalloc() fails. The caller of
mlx5e_create_l2_table_groups() does not catch this
issue on failure, which leads to memleak.
Fixes: 33cfaaa8f36f ("net/mlx5e: Split the main flow steering table") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Dinghao Liu [Mon, 28 Dec 2020 08:48:40 +0000 (16:48 +0800)]
net/mlx5e: Fix two double free cases
mlx5e_create_ttc_table_groups() frees ft->g on failure of
kvzalloc(), but such failure will be caught by its caller
in mlx5e_create_ttc_table() and ft->g will be freed again
in mlx5e_destroy_flow_table(). The same issue also occurs
in mlx5e_create_ttc_table_groups(). Set ft->g to NULL after
kfree() to avoid double free.
Fixes: 7b3722fa9ef6 ("net/mlx5e: Support RSS for GRE tunneled packets") Fixes: 33cfaaa8f36f ("net/mlx5e: Split the main flow steering table") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Aya Levin [Sun, 27 Dec 2020 14:33:19 +0000 (16:33 +0200)]
net/mlx5e: ethtool, Fix restriction of autoneg with 56G
Prior to this patch, configuring speed to 50G with autoneg off over
devices supporting 50G per lane failed.
Support for 50G per lane introduced a new set of link-modes, on which
driver always performed a speed validation as if only legacy link-modes
were configured. Fix driver speed validation to force setting autoneg
over 56G only if in legacy link-mode.
Fixes: 3d7cadae51f1 ("net/mlx5e: ethtool, Fix analysis of speed setting") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maor Dickman [Mon, 14 Dec 2020 11:53:03 +0000 (13:53 +0200)]
net/mlx5e: In skb build skip setting mark in switchdev mode
sop_drop_qpn field in the cqe is used by two features, in SWITCHDEV mode
to restore the chain id in case of a miss and in LEGACY mode to support
skbedit mark action. In build RX skb, the skb mark field is set regardless
of the configured mode which cause a corruption of the mark field in case
of switchdev mode.
Fix by overriding the mark value back to 0 in the representor tc update
skb flow.
Fixes: 8f1e0b97cc70 ("net/mlx5: E-Switch, Mark miss packets with new chain id mapping") Signed-off-by: Maor Dickman <maord@nvidia.com> Reviewed-by: Raed Salem <raeds@nvidia.com> Reviewed-by: Oz Shlomo <ozsh@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Alaa Hleihel [Mon, 4 Jan 2021 10:54:40 +0000 (12:54 +0200)]
net/mlx5: E-Switch, fix changing vf VLANID
Adding vf VLANID for the first time, or after having cleared previously
defined VLANID works fine, however, attempting to change an existing vf
VLANID clears the rules on the firmware, but does not add new rules for
the new vf VLANID.
Fix this by changing the logic in function esw_acl_egress_lgcy_setup()
so that it will always configure egress rules.
Moshe Shemesh [Fri, 13 Nov 2020 04:06:28 +0000 (06:06 +0200)]
net/mlx5e: Fix SWP offsets when vlan inserted by driver
In case WQE includes inline header the vlan is inserted by driver even
if vlan offload is set. On geneve over vlan interface where software
parser is used the SWP offsets should be updated according to the added
vlan.
Oz Shlomo [Mon, 7 Dec 2020 08:15:18 +0000 (08:15 +0000)]
net/mlx5e: CT: Use per flow counter when CT flow accounting is enabled
Connection counters may be shared for both directions when the counter
is used for connection aging purposes. However, if TC flow
accounting is enabled then a unique counter is required per direction.
Instantiate a unique counter per direction if the conntrack accounting
extension is enabled. Use a shared counter when the connection accounting
extension is disabled.
Fixes: 1edae2335adf ("net/mlx5e: CT: Use the same counter for both directions") Signed-off-by: Oz Shlomo <ozsh@nvidia.com> Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Paul Blakey <paulb@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Aya Levin [Tue, 24 Nov 2020 20:16:23 +0000 (22:16 +0200)]
net/mlx5e: Add missing capability check for uplink follow
Expose firmware indication that it supports setting eswitch uplink state
to follow (follow the physical link). Condition setting the eswitch
uplink admin-state with this capability bit. Older FW may not support
the uplink state setting.
Fixes: 7d0314b11cdd ("net/mlx5e: Modify uplink state on interface up/down") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Fixes: 9b412cc35f00 ("net/mlx5e: Add LAG warning if bond slave is not lag master") Signed-off-by: Mark Zhang <markzhang@nvidia.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Linus Torvalds [Thu, 7 Jan 2021 20:21:32 +0000 (12:21 -0800)]
Merge tag 'spi-fix-v5.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A couple of core fixes here, both to do with handling of drivers which
don't report their maximum speed since we factored some of the
handling for transfer speeds out into the core in the previous
release.
There's also some driver specific fixes, including a relatively large
set for some races around timeouts in spi-geni-qcom"
* tag 'spi-fix-v5.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: fix the divide by 0 error when calculating xfer waiting time
spi: Fix the clamping of spi->max_speed_hz
spi: altera: fix return value for altera_spi_txrx()
spi: stm32: FIFO threshold level - fix align packet size
spi: spi-geni-qcom: Print an error when we timeout setting the CS
spi: spi-geni-qcom: Don't try to set CS if an xfer is pending
spi: spi-geni-qcom: Fail new xfers if xfer/cancel/abort pending
spi: spi-geni-qcom: Fix geni_spi_isr() NULL dereference in timeout case
Sean Tranchetti [Wed, 6 Jan 2021 00:22:26 +0000 (16:22 -0800)]
tools: selftests: add test for changing routes with PTMU exceptions
Adds new 2 new tests to the PTMU script: pmtu_ipv4/6_route_change.
These tests explicitly test for a recently discovered problem in the
IPv6 routing framework where PMTU exceptions were not properly released
when replacing a route via "ip route change ...".
After creating PMTU exceptions, the route from the device A to R1 will be
replaced with a new route, then device A will be deleted. If the PMTU
exceptions were properly cleaned up by the kernel, this device deletion
will succeed. Otherwise, the unregistration of the device will stall, and
messages such as the following will be logged in dmesg:
unregister_netdevice: waiting for veth_A-R1 to become free. Usage count = 4
Sean Tranchetti [Wed, 6 Jan 2021 00:22:25 +0000 (16:22 -0800)]
net: ipv6: fib: flush exceptions when purging route
Route removal is handled by two code paths. The main removal path is via
fib6_del_route() which will handle purging any PMTU exceptions from the
cache, removing all per-cpu copies of the DST entry used by the route, and
releasing the fib6_info struct.
The second removal location is during fib6_add_rt2node() during a route
replacement operation. This path also calls fib6_purge_rt() to handle
cleaning up the per-cpu copies of the DST entries and releasing the
fib6_info associated with the older route, but it does not flush any PMTU
exceptions that the older route had. Since the older route is removed from
the tree during the replacement, we lose any way of accessing it again.
As these lingering DSTs and the fib6_info struct are holding references to
the underlying netdevice struct as well, unregistering that device from the
kernel can never complete.
Linus Torvalds [Thu, 7 Jan 2021 19:57:56 +0000 (11:57 -0800)]
Merge tag 'regmap-fix-v5.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"A couple of small fixes for leaks when attaching a device to a
preexisting regmap"
* tag 'regmap-fix-v5.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: debugfs: Fix a reversed if statement in regmap_debugfs_init()
regmap: debugfs: Fix a memory leak when calling regmap_attach_dev
Jakub Kicinski [Thu, 7 Jan 2021 19:08:08 +0000 (11:08 -0800)]
Merge tag 'linux-can-fixes-for-5.11-20210107' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2021-01-07
The first patch is by me for the m_can driver and removes an erroneous
m_can_clk_stop() from the driver's unregister function.
The second patch targets the tcan4x5x driver, is by me, and fixes the bit
timing constant parameters.
The next two patches are by me, target the mcp251xfd driver, and fix a race
condition in the optimized TEF path (which was added in net-next for v5.11).
The similar code in the RX path is changed to look the same, although it
doesn't suffer from the race condition.
A patch by Lad Prabhakar updates the description and help text for the rcar CAN
driver to reflect all supported SoCs.
In the last patch Sriram Dash transfers the maintainership of the m_can driver
to Pankaj Sharma.
* tag 'linux-can-fixes-for-5.11-20210107' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
MAINTAINERS: Update MCAN MMIO device driver maintainer
can: rcar: Kconfig: update help description for CAN_RCAR config
can: mcp251xfd: mcp251xfd_handle_rxif_ring(): first increment RX tail pointer in HW, then in driver
can: mcp251xfd: mcp251xfd_handle_tefif(): fix TEF vs. TX race condition
can: tcan4x5x: fix bittiming const, use common bittiming from m_can driver
can: m_can: m_can_class_unregister(): remove erroneous m_can_clk_stop()
====================
can: mcp251xfd: mcp251xfd_handle_rxif_ring(): first increment RX tail pointer in HW, then in driver
The previous patch fixes a TEF vs. TX race condition, by first updating the TEF
tail pointer in hardware, and then updating the driver internal pointer.
The same pattern exists in the RX-path, too. This should be no problem, as the
driver accesses the RX-FIFO from the interrupt handler only, thus the access is
properly serialized. Fix the order here, too, so that the TEF- and RX-path look
similar.
can: mcp251xfd: mcp251xfd_handle_tefif(): fix TEF vs. TX race condition
The mcp251xfd driver uses a TX FIFO for sending CAN frames and a TX Event FIFO
(TEF) for completed TX-requests.
The TEF event handling in the mcp251xfd_handle_tefif() function has a race
condition. It first increments the tx-ring's tail counter to signal that
there's room in the TX and TEF FIFO, then it increments the TEF FIFO in
hardware.
A running mcp251xfd_start_xmit() on a different CPU might not stop the txqueue
(as the tx-ring still shows free space). The next mcp251xfd_start_xmit() will
push a message into the chip and the TX complete event might overflow the TEF
FIFO.
can: tcan4x5x: fix bittiming const, use common bittiming from m_can driver
According to the TCAN4550 datasheet "SLLSF91 - DECEMBER 2018" the tcan4x5x has
the same bittiming constants as a m_can revision 3.2.x/3.3.0.
The tcan4x5x chip I'm using identifies itself as m_can revision 3.2.1, so
remove the tcan4x5x specific bittiming values and rely on the values in the
m_can driver, which are selected according to core revision.
Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel") Cc: Dan Murphy <dmurphy@ti.com> Reviewed-by: Sean Nyekjaer <sean@geanix.com> Link: https://lore.kernel.org/r/20201215103238.524029-3-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Randy Dunlap [Wed, 6 Jan 2021 04:25:31 +0000 (20:25 -0800)]
ptp: ptp_ines: prevent build when HAS_IOMEM is not set
ptp_ines.c uses devm_platform_ioremap_resource(), which is only
built/available when CONFIG_HAS_IOMEM is enabled.
CONFIG_HAS_IOMEM is not enabled for arch/s390/, so builds on S390
have a build error:
s390-linux-ld: drivers/ptp/ptp_ines.o: in function `ines_ptp_ctrl_probe':
ptp_ines.c:(.text+0x17e6): undefined reference to `devm_platform_ioremap_resource'
Prevent builds of ptp_ines.c when HAS_IOMEM is not set.
Fixes: bad1eaa6ac31 ("ptp: Add a driver for InES time stamping IP core.") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com>
Link: lore.kernel.org/r/202101031125.ZEFCUiKi-lkp@intel.com Acked-by: Richard Cochran <richardcochran@gmail.com> Link: https://lore.kernel.org/r/20210106042531.1351-1-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Randy Dunlap [Wed, 6 Jan 2021 02:18:15 +0000 (18:18 -0800)]
net: dsa: fix led_classdev build errors
Fix build errors when LEDS_CLASS=m and NET_DSA_HIRSCHMANN_HELLCREEK=y.
This limits the latter to =m when LEDS_CLASS=m.
microblaze-linux-ld: drivers/net/dsa/hirschmann/hellcreek_ptp.o: in function `hellcreek_ptp_setup':
(.text+0xf80): undefined reference to `led_classdev_register_ext'
microblaze-linux-ld: (.text+0xf94): undefined reference to `led_classdev_register_ext'
microblaze-linux-ld: drivers/net/dsa/hirschmann/hellcreek_ptp.o: in function `hellcreek_ptp_free':
(.text+0x1018): undefined reference to `led_classdev_unregister'
microblaze-linux-ld: (.text+0x1024): undefined reference to `led_classdev_unregister'
Alan Maguire [Wed, 6 Jan 2021 15:59:06 +0000 (15:59 +0000)]
bpftool: Fix compilation failure for net.o with older glibc
For older glibc ~2.17, #include'ing both linux/if.h and net/if.h
fails due to complaints about redefinition of interface flags:
CC net.o
In file included from net.c:13:0:
/usr/include/linux/if.h:71:2: error: redeclaration of enumerator ‘IFF_UP’
IFF_UP = 1<<0, /* sysfs */
^
/usr/include/net/if.h:44:5: note: previous definition of ‘IFF_UP’ was here
IFF_UP = 0x1, /* Interface is up. */
The issue was fixed in kernel headers in [1], but since compilation
of net.c picks up system headers the problem can recur.
Dropping #include <linux/if.h> resolves the issue and it is
not needed for compilation anyhow.
Valdis Klētnieks [Sat, 26 Dec 2020 18:21:58 +0000 (13:21 -0500)]
gcc-plugins: fix gcc 11 indigestion with plugins...
Fedora Rawhide has started including gcc 11,and the g++ compiler
throws a wobbly when it hits scripts/gcc-plugins:
HOSTCXX scripts/gcc-plugins/latent_entropy_plugin.so
In file included from /usr/include/c++/11/type_traits:35,
from /usr/lib/gcc/x86_64-redhat-linux/11/plugin/include/system.h:244,
from /usr/lib/gcc/x86_64-redhat-linux/11/plugin/include/gcc-plugin.h:28,
from scripts/gcc-plugins/gcc-common.h:7,
from scripts/gcc-plugins/latent_entropy_plugin.c:78:
/usr/include/c++/11/bits/c++0x_warning.h:32:2: error: #error This file requires compiler and library support for the ISO
C++ 2011 standard. This support must be enabled with the -std=c++11 or -std=gnu++11 compiler options.
32 | #error This file requires compiler and library support \
In fact, it works just fine with c++11, which has been in gcc since 4.8,
and we now require 4.9 as a minimum.
Linus Torvalds [Wed, 6 Jan 2021 19:19:08 +0000 (11:19 -0800)]
Merge tag 'for-5.11-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A few more fixes that arrived before the end of the year:
- a bunch of fixes related to transaction handle lifetime wrt various
operations (umount, remount, qgroup scan, orphan cleanup)
- async discard scheduling fixes
- fix item size calculation when item keys collide for extend refs
(hardlinks)
- fix qgroup flushing from running transaction
- fix send, wrong file path when there is an inode with a pending
rmdir
- fix deadlock when cloning inline extent and low on free metadata
space"
* tag 'for-5.11-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: run delayed iputs when remounting RO to avoid leaking them
btrfs: add assertion for empty list of transactions at late stage of umount
btrfs: fix race between RO remount and the cleaner task
btrfs: fix transaction leak and crash after cleaning up orphans on RO mount
btrfs: fix transaction leak and crash after RO remount caused by qgroup rescan
btrfs: merge critical sections of discard lock in workfn
btrfs: fix racy access to discard_ctl data
btrfs: fix async discard stall
btrfs: tests: initialize test inodes location
btrfs: send: fix wrong file path when there is an inode with a pending rmdir
btrfs: qgroup: don't try to wait flushing if we're already holding a transaction
btrfs: correctly calculate item size used when item key collision happens
btrfs: fix deadlock when cloning inline extent and low on free metadata space
Jiri Olsa [Tue, 5 Jan 2021 23:42:19 +0000 (00:42 +0100)]
tools/resolve_btfids: Warn when having multiple IDs for single type
The kernel image can contain multiple types (structs/unions)
with the same name. This causes distinct type hierarchies in
BTF data and makes resolve_btfids fail with error like:
BTFIDS vmlinux
FAILED unresolved symbol udp6_sock
as reported by Qais Yousef [1].
This change adds warning when multiple types of the same name
are detected:
BTFIDS vmlinux
WARN: multiple IDs found for 'file': 526, 113351 - using 526
WARN: multiple IDs found for 'sk_buff': 2744, 113958 - using 2744
We keep the lower ID for the given type instance and let the
build continue.
Also changing the 'nr' variable name to 'nr_types' to avoid confusion.
Qinglang Miao [Tue, 5 Jan 2021 05:57:54 +0000 (13:57 +0800)]
net: qrtr: fix null-ptr-deref in qrtr_ns_remove
A null-ptr-deref bug is reported by Hulk Robot like this:
--------------
KASAN: null-ptr-deref in range [0x0000000000000128-0x000000000000012f]
Call Trace:
qrtr_ns_remove+0x22/0x40 [ns]
qrtr_proto_fini+0xa/0x31 [qrtr]
__x64_sys_delete_module+0x337/0x4e0
do_syscall_64+0x34/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x468ded
--------------
When qrtr_ns_init fails in qrtr_proto_init, qrtr_ns_remove which would
be called later on would raise a null-ptr-deref because qrtr_ns.workqueue
has been destroyed.
Fix it by making qrtr_ns_init have a return value and adding a check in
qrtr_proto_init.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: cdc_ncm: correct overhead in delayed_ndp_size
Aligning to tx_ndp_modulus is not sufficient because the next align
call can be cdc_ncm_align_tail, which can add up to ctx->tx_modulus +
ctx->tx_remainder - 1 bytes. This used to lead to occasional crashes
on a Huawei 909s-120 LTE module as follows:
- the condition marked /* if there is a remaining skb [...] */ is true
so the swaps happen
- skb_out is set from ctx->tx_curr_skb
- skb_out->len is exactly 0x3f52
- ctx->tx_curr_size is 0x4000 and delayed_ndp_size is 0xac
(note that the sum of skb_out->len and delayed_ndp_size is 0x3ffe)
- the for loop over n is executed once
- the cdc_ncm_align_tail call marked /* align beginning of next frame */
increases skb_out->len to 0x3f56 (the sum is now 0x4002)
- the condition marked /* check if we had enough room left [...] */ is
false so we break out of the loop
- the condition marked /* If requested, put NDP at end of frame. */ is
true so the NDP is written into skb_out
- now skb_out->len is 0x4002, so padding_count is minus two interpreted
as an unsigned number, which is used as the length argument to memset,
leading to a crash with various symptoms but usually including
The cdc_ncm_align_tail call first aligns on a ctx->tx_modulus
boundary (adding at most ctx->tx_modulus-1 bytes), then adds
ctx->tx_remainder bytes. Alternatively, the next alignment call can
occur in cdc_ncm_ndp16 or cdc_ncm_ndp32, in which case at most
ctx->tx_ndp_modulus-1 bytes are added.
A similar problem has occurred before, and the code is nontrivial to
reason about, so add a guard before the crashing call. By that time it
is too late to prevent any memory corruption (we'll have written past
the end of the buffer already) but we can at least try to get a warning
written into an on-disk log by avoiding the hard crash caused by padding
past the buffer with a huge number of zeros.
Signed-off-by: Jouni K. Seppänen <jks@iki.fi> Fixes: 4a0e3e989d66 ("cdc_ncm: Add support for moving NDP to end of NCM frame") Link: https://bugzilla.kernel.org/show_bug.cgi?id=209407 Reported-by: kernel test robot <lkp@intel.com> Reviewed-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Tue, 5 Jan 2021 03:37:28 +0000 (11:37 +0800)]
net: hns3: fix incorrect handling of sctp6 rss tuple
For DEVICE_VERSION_V2, the hardware only supports src-ip,
dst-ip and verification-tag for rss tuple set of sctp6
packet. For DEVICE_VERSION_V3, the hardware supports
src-port and dst-port as well.
Currently, when user queries the sctp6 rss tuples info,
some unsupported information will be showed on V2. So add
a check for hardware version when initializing and queries
sctp6 rss tuple to fix this issue.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yufeng Mo [Tue, 5 Jan 2021 03:37:27 +0000 (11:37 +0800)]
net: hns3: fix the number of queues actually used by ARQ
HCLGE_MBX_MAX_ARQ_MSG_NUM is used to apply memory for the number
of queues used by ARQ(Asynchronous Receive Queue), so the head
and tail pointers should also use this macro.
Fixes: 07a0556a3a73 ("net: hns3: Changes to support ARQ(Asynchronous Receive Queue)") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yonglong Liu [Tue, 5 Jan 2021 03:37:26 +0000 (11:37 +0800)]
net: hns3: fix a phy loopback fail issue
When phy driver does not implement the set_loopback interface,
phy loopback test will return -EOPNOTSUPP, and the loopback test
will fail. So when phy driver does not implement the set_loopback
interface, don't do phy loopback test.
Fixes: c9765a89d142 ("net: hns3: add phy selftest function") Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 6 Jan 2021 00:32:08 +0000 (16:32 -0800)]
Merge branch 'stmmac-fixes'
Samuel Holland says:
====================
Fixes for dwmac-sun8i suspend/resume
This series fixes issues preventing dwmac-sun8i from working after a
suspend/resume cycle. Those issues include the PHY being left powered
off, the MAC syscon configuration being reset, and the reference to the
reset controller being improperly dropped. They also fix related issues
in probe error handling and driver removal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, sun8i_dwmac_set_syscon was called from a chain of functions
in several different files:
sun8i_dwmac_probe
stmmac_dvr_probe
stmmac_hw_init
stmmac_hwif_init
sun8i_dwmac_setup
sun8i_dwmac_set_syscon
which made the lifetime of the syscon values hard to reason about. Part
of the problem is that there is no similar platform driver callback from
stmmac_dvr_remove. As a result, the driver unset the syscon value in
sun8i_dwmac_exit, but this leaves it uninitialized after a suspend/
resume cycle. It was also unset a second time (outside sun8i_dwmac_exit)
in the probe error path.
Move the init to the earliest available place in sun8i_dwmac_probe
(after stmmac_probe_config_dt, which initializes plat_dat), and the
deinit to the corresponding position in the cleanup order.
Since priv is not filled in until stmmac_dvr_probe, this requires
changing the sun8i_dwmac_set_syscon parameters to priv's two relevant
members.
Fixes: 9f93ac8d4085 ("net-next: stmmac: Add dwmac-sun8i") Fixes: 634db83b8265 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs") Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Samuel Holland [Sun, 3 Jan 2021 11:17:43 +0000 (05:17 -0600)]
net: stmmac: dwmac-sun8i: Balance internal PHY power
sun8i_dwmac_exit calls sun8i_dwmac_unpower_internal_phy, but
sun8i_dwmac_init did not call sun8i_dwmac_power_internal_phy. This
caused PHY power to remain off after a suspend/resume cycle. Fix this by
recording if PHY power should be restored, and if so, restoring it.
Fixes: 634db83b8265 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs") Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: David S. Miller <davem@davemloft.net>
While stmmac_pltfr_remove calls sun8i_dwmac_exit, the sun8i_dwmac_init
and sun8i_dwmac_exit functions are also called by the stmmac_platform
suspend/resume callbacks. They may be called many times during the
device's lifetime and should not release resources used by the driver.
Furthermore, there was no error handling in case registering the MDIO
mux failed during probe, and the EPHY clock was never released at all.
Fix all of these issues by moving the deinitialization code to a driver
removal callback. Also ensure the EPHY is powered down before removal.
Fixes: 634db83b8265 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs") Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_pltfr_remove does three things in one function, making it
inapproprate for unwinding the steps in the probe function. Currently,
a failure before the call to stmmac_dvr_probe would leak OF node
references due to missing a call to stmmac_remove_config_dt. And an
error in stmmac_dvr_probe would cause the driver to attempt to remove a
netdevice that was never added. Fix these by reordering the init and
splitting out the error handling steps.
Fixes: 9f93ac8d4085 ("net-next: stmmac: Add dwmac-sun8i") Fixes: 40a1dcee2d18 ("net: ethernet: dwmac-sun8i: Use the correct function in exit path") Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 31 Dec 2020 03:40:27 +0000 (19:40 -0800)]
net: vlan: avoid leaks on register_vlan_dev() failures
VLAN checks for NETREG_UNINITIALIZED to distinguish between
registration failure and unregistration in progress.
Since commit cb626bf566eb ("net-sysfs: Fix reference count leak")
registration failure may, however, result in NETREG_UNREGISTERED
as well as NETREG_UNINITIALIZED.
This fix is similer to cebb69754f37 ("rtnetlink: Fix
memory(net_device) leak when ->newlink fails")
Fixes: cb626bf566eb ("net-sysfs: Fix reference count leak") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net/sonic: Fix some resource leaks in error handling paths
A call to dma_alloc_coherent() is wrapped by sonic_alloc_descriptors().
This is correctly freed in the remove function, but not in the error
handling path of the probe function. Fix this by adding the missing
dma_free_coherent() call.
While at it, rename a label in order to be slightly more informative.
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Chris Zankel <chris@zankel.net>
References: commit 10e3cc180e64 ("net/sonic: Fix a resource leak in an error handling path in 'jazz_sonic_probe()'") Fixes: 74f2a5f0ef64 ("xtensa: Add support for the Sonic Ethernet device for the XT2000 board.") Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Sun, 3 Jan 2021 21:36:23 +0000 (22:36 +0100)]
wan: ds26522: select CONFIG_BITREVERSE
Without this, the driver runs into a link failure
arm-linux-gnueabi-ld: drivers/net/wan/slic_ds26522.o: in function `slic_ds26522_probe':
slic_ds26522.c:(.text+0x100c): undefined reference to `byte_rev_table'
arm-linux-gnueabi-ld: slic_ds26522.c:(.text+0x1cdc): undefined reference to `byte_rev_table'
arm-linux-gnueabi-ld: drivers/net/wan/slic_ds26522.o: in function `slic_write':
slic_ds26522.c:(.text+0x1e4c): undefined reference to `byte_rev_table'
Fixes: c37d4a0085c5 ("Maxim/driver: Add driver for maxim ds26522") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Sun, 3 Jan 2021 21:36:22 +0000 (22:36 +0100)]
misdn: dsp: select CONFIG_BITREVERSE
Without this, we run into a link error
arm-linux-gnueabi-ld: drivers/isdn/mISDN/dsp_audio.o: in function `dsp_audio_generate_law_tables':
(.text+0x30c): undefined reference to `byte_rev_table'
arm-linux-gnueabi-ld: drivers/isdn/mISDN/dsp_audio.o:(.text+0x5e4): more undefined references to `byte_rev_table' follow
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Sun, 3 Jan 2021 21:36:21 +0000 (22:36 +0100)]
cfg80211: select CONFIG_CRC32
Without crc32 support, this fails to link:
arm-linux-gnueabi-ld: net/wireless/scan.o: in function `cfg80211_scan_6ghz':
scan.c:(.text+0x928): undefined reference to `crc32_le'
Fixes: c8cb5b854b40 ("nl80211/cfg80211: support 6 GHz scanning") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Sun, 3 Jan 2021 21:36:20 +0000 (22:36 +0100)]
wil6210: select CONFIG_CRC32
Without crc32, the driver fails to link:
arm-linux-gnueabi-ld: drivers/net/wireless/ath/wil6210/fw.o: in function `wil_fw_verify':
fw.c:(.text+0x74c): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/wireless/ath/wil6210/fw.o:fw.c:(.text+0x758): more undefined references to `crc32_le' follow
Fixes: 151a9706503f ("wil6210: firmware download") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Sun, 3 Jan 2021 21:36:19 +0000 (22:36 +0100)]
can: kvaser_pciefd: select CONFIG_CRC32
Without crc32, this driver fails to link:
arm-linux-gnueabi-ld: drivers/net/can/kvaser_pciefd.o: in function `kvaser_pciefd_probe':
kvaser_pciefd.c:(.text+0x2b0): undefined reference to `crc32_be'
Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Sun, 3 Jan 2021 21:36:18 +0000 (22:36 +0100)]
phy: dp83640: select CONFIG_CRC32
Without crc32, this driver fails to link:
arm-linux-gnueabi-ld: drivers/net/phy/dp83640.o: in function `match':
dp83640.c:(.text+0x476c): undefined reference to `crc32_le'
Fixes: 539e44d26855 ("dp83640: Include hash in timestamp/packet matching") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Sun, 3 Jan 2021 21:36:17 +0000 (22:36 +0100)]
qed: select CONFIG_CRC32
Without this, the driver fails to link:
lpc_eth.c:(.text+0x1934): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/qlogic/qed/qed_debug.o: in function `qed_grc_dump':
qed_debug.c:(.text+0x4068): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/qlogic/qed/qed_debug.o: in function `qed_idle_chk_dump':
qed_debug.c:(.text+0x51fc): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/qlogic/qed/qed_debug.o: in function `qed_mcp_trace_dump':
qed_debug.c:(.text+0x6000): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/qlogic/qed/qed_debug.o: in function `qed_dbg_reg_fifo_dump':
qed_debug.c:(.text+0x66cc): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/qlogic/qed/qed_debug.o:qed_debug.c:(.text+0x6aa4): more undefined references to `crc32_le' follow
Fixes: 7a4b21b7d1f0 ("qed: Add nvram selftest") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 5 Jan 2021 21:25:49 +0000 (13:25 -0800)]
Merge tag 'sound-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here is a collection of USB- and HD-audio fixes.
Most of them are device-specific quirks while one fix is for a
regression due to an incorrect mutex unlock introduced in this merge
window"
* tag 'sound-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/via: Fix runtime PM for Clevo W35xSS
ALSA: usb-audio: Add quirk for RC-505
ALSA: hda/hdmi: Fix incorrect mutex unlock in silent_stream_disable()
ALSA: hda/realtek: Enable mute and micmute LED on HP EliteBook 850 G7
ALSA: hda/realtek: Add two "Intel Reference board" SSID in the ALC256.
ALSA: hda/realtek: Add mute LED quirk for more HP laptops
ALSA: hda/conexant: add a new hda codec CX11970
ALSA: usb-audio: Add quirk for BOSS AD-10
ALSA: usb-audio: Fix UBSAN warnings for MIDI jacks
ALSA: hda/realtek - Modify Dell platform name
ALSA: hda/realtek - Fix speaker volume control on Lenovo C940
Linus Torvalds [Tue, 5 Jan 2021 20:46:27 +0000 (12:46 -0800)]
Merge tag 'arc-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"Things are quieter on upstreaming front as we are mostly focusing on
ARCv3/ARC64 port.
This contains just build system updates from Masahiro Yamada"
* tag 'arc-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: build: use $(READELF) instead of hard-coded readelf
ARC: build: remove unneeded extra-y
ARC: build: move symlink creation to arch/arc/Makefile to avoid race
ARC: build: add boot_targets to PHONY
ARC: build: add uImage.lzma to the top-level target
ARC: build: remove non-existing bootpImage from KBUILD_IMAGE
projects / mirror_ubuntu-kernels.git / log