cat /sys/kernel/debug/mmc0/regs will hang up the system since
it's in runtime suspended state, so the genpd and biu_clk is
off. This patch fixes this problem by calling pm_runtime_get_sync
to wake it up before reading the registers.
Tuning can leave the IP in an active state (Buffer Read Enable bit set)
which prevents the entry to low power states (i.e. S0i3). Data reset will
clear it.
Generally tuning is followed by a data transfer which will anyway sort out
the state, so it is rare that S0i3 is actually prevented.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
We've added a quirk to enable the recent Lenovo dock support, where it
overwrites the pin configs of NID 0x17 and 19, not only updating the
pin config cache. It works right after the boot, but the problem is
that the pin configs are occasionally cleared when the machine goes to
PM. Meanwhile the quirk writes the pin configs only at the pre-probe,
so this won't be applied any longer.
For addressing that issue, this patch moves the code to overwrite the
pin configs into HDA_FIXUP_ACT_INIT section so that it's always
applied at both probe and resume time.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195161 Fixes: 61fcf8ece9b6 ("ALSA: hda/realtek - Enable Thinkpad Dock device for ALC298 platform") Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
On some boards setting power_save to a non 0 value leads to clicking /
popping sounds when ever we enter/leave powersaving mode. Ideally we would
figure out how to avoid these sounds, but that is not always feasible.
This commit adds a blacklist for devices where powersaving is known to
cause problems and disables it on these devices.
Note I tried to put this blacklist in userspace first:
https://github.com/systemd/systemd/pull/8128
But the systemd maintainers rightfully pointed out that it would be
impossible to then later remove entries once we actually find a way to
make power-saving work on listed boards without issues. Having this list
in the kernel will allow removal of the blacklist entry in the same commit
which fixes the clicks / plops.
The blacklist only applies to the default power_save module-option value,
if a user explicitly sets the module-option then the blacklist is not
used.
[ added an ifdef CONFIG_PM for the build error -- tiwai]
The commit change for supporting the multiple ports moved involved
some code shuffling, and there the initializations of spinlock and
mutex in snd_intelhad object were dropped mistakenly.
This patch adds the missing initializations again for each port.
Fixes: b4eb0d522fcb ("ALSA: x86: Split snd_intelhad into card and PCM specific structures") Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The patch "ALSA: control: code refactoring for ELEM_READ/ELEM_WRITE
operations" introduced a potential for kernel memory corruption due
to an incorrect if statement allowing non-readable controls to fall
through and call the get function. For TLV controls a driver can omit
SNDRV_CTL_ELEM_ACCESS_READ to ensure that only the TLV get function
can be called. Instead the normal get() can be invoked unexpectedly
and as the driver expects that this will only be called for controls
<= 512 bytes, potentially try to copy >512 bytes into the 512 byte
return array, so corrupting kernel memory.
The problem is an attempt to refactor the snd_ctl_elem_read function
to invert the logic so that it conditionally aborted if the control
is unreadable instead of conditionally executing. But the if statement
wasn't inverted correctly.
The correct inversion of
if (a && !b)
is
if (!a || b)
Fixes: becf9e5d553c2 ("ALSA: control: code refactoring for ELEM_READ/ELEM_WRITE operations") Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust> Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.morris@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust> Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.morris@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust> Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.morris@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. If a bit does
flip it could cause an overrun if it's in one of the size parameters,
so sanity check that we're not overrunning the provided buffer when
doing a memcpy().
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust> Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.morris@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust> Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.morris@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Add check for build_skb enabled ring in ixgbe_dma_sync_frag().
In that case &skb_shinfo(skb)->frags[0] may not always be set which
can lead to a crash. Instead we derive the page offset from skb->data.
Fixes: 42073d91a214 ("ixgbe: Have the CPU take ownership of the buffers sooner") CC: stable <stable@vger.kernel.org> Reported-by: Ambarish Soman <asoman@redhat.com> Suggested-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Commit 61f5acea8737 ("Bluetooth: btusb: Restore QCA Rome suspend/resume fix
with a "rewritten" version") applied the USB_QUIRK_RESET_RESUME to all QCA
USB Bluetooth modules. But it turns out that the resume problems are not
caused by the QCA Rome chipset, on most platforms it resumes fine. The
resume problems are actually a platform problem (likely the platform
cutting all power when suspended).
The USB_QUIRK_RESET_RESUME quirk also disables runtime suspend, so by
matching on usb-ids, we're causing all boards with these chips to use extra
power, to fix resume problems which only happen on some boards.
This commit fixes this by applying the quirk based on DMI matching instead
of on usb-ids, so that we match the platform and not the chipset.
Here is the /sys/kernel/debug/usb/devices for the Bluetooth module:
Currently if the kernel receives a memory hot-unplug event early
enough, it may get stuck in an infinite loop in
dissolve_free_huge_pages(). This appears as a stall just after:
pseries-hotplug-mem: Attempting to hot-remove XX LMB(s) at YYYYYYYY
It appears to be caused by "minimum_order" being uninitialized, due to
init_ras_IRQ() executing before hugetlb_init().
To correct this, extract the part of init_ras_IRQ() that enables
hotplug event processing and place it in the machine_late_initcall
phase, which is guaranteed to be after hugetlb_init() is called.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com> Acked-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Reorder the functions to make the diff readable] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Cleanup of platform devices created by the IPMI driver was not
being done correctly and could result in a memory leak. So
create a local boolean to know how to clean up those platform
devices.
Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Corey Minyard <cminyard@mvista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The POSIX specification defines that relative CLOCK_REALTIME timers are not
affected by clock modifications. Those timers have to use CLOCK_MONOTONIC
to ensure POSIX compliance.
The introduction of the additional HRTIMER_MODE_PINNED mode broke this
requirement for pinned timers.
There is no user space visible impact because user space timers are not
using pinned mode, but for consistency reasons this needs to be fixed.
Check whether the mode has the HRTIMER_MODE_REL bit set instead of
comparing with HRTIMER_MODE_ABS.
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de> Cc: Christoph Hellwig <hch@lst.de> Cc: John Stultz <john.stultz@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: keescook@chromium.org Fixes: 597d0275736d ("timers: Framework for identifying pinned timers") Link: http://lkml.kernel.org/r/20171221104205.7269-7-anna-maria@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Mike Galbraith <efault@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Colin Ian King [Thu, 8 Mar 2018 11:11:54 +0000 (12:11 +0100)]
UBUNTU: SAUCE: Fix ZFS setgid
BugLink: http://bugs.launchpad.net/bugs/1753288
Pull in upstream commit 0e85048f53e4, namely:
"Take user namespaces into account in policy checks"
- Change file related checks to use user namespaces and make
sure involved uids/gids are mappable in the current
namespace.
- Sync'd from zfsutils-linux 0.7.5-1ubuntu5
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Michael Ellerman [Thu, 22 Feb 2018 13:00:11 +0000 (00:00 +1100)]
powerpc/powernv: Support firmware disable of RFI flush
BugLink: http://bugs.launchpad.net/bugs/1751994
Some versions of firmware will have a setting that can be configured
to disable the RFI flush, add support for it.
Fixes: 6e032b350cd1 ("powerpc/powernv: Check device-tree for RFI flush settings") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit eb0a2d2620ae431c543963c8c7f08f597366fc60) Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Michael Ellerman [Thu, 22 Feb 2018 12:58:49 +0000 (23:58 +1100)]
powerpc/pseries: Support firmware disable of RFI flush
BugLink: http://bugs.launchpad.net/bugs/1751994
Some versions of firmware will have a setting that can be configured
to disable the RFI flush, add support for it.
Fixes: 8989d56878a7 ("powerpc/pseries: Query hypervisor for RFI flush settings") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 582605a429e20ae68fd0b041b2e840af296edd08) Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Mika Westerberg [Mon, 27 Nov 2017 13:54:44 +0000 (16:54 +0300)]
pinctrl: cannonlake: Align GPIO number space with Windows
BugLink: http://bugs.launchpad.net/bugs/1751714
The Cannon Lake Windows GPIO driver always exposes 32 pins per "bank"
regardless of whether the hardware actually has that many pins in a pad
group. This means that there are gaps in the GPIO number space even if
such gaps do not exist in the real hardware. To make things worse the
BIOS is also using the same scheme, so for example on Cannon Lake-LP
vGPIO 39 (vSD3_CD_B) the ACPI GpioInt resource has number 231 instead of
the expected 180 (which would be the hardware number).
To make SD card detection and other GPIOs working properly in Linux we
align the pinctrl-cannonlake GPIO numbering to follow the Windows GPIO
driver numbering taking advantage of the gpio_base field introduced in
the previous patch.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit cb5fda413e1d4a857bf4fd0bc92e9de0f1ff9e9d) Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Mika Westerberg [Mon, 27 Nov 2017 13:54:43 +0000 (16:54 +0300)]
pinctrl: intel: Allow custom GPIO base for pad groups
BugLink: http://bugs.launchpad.net/bugs/1751714
Currently we always have direct mapping between GPIO numbers and the
hardware pin numbers. However, there are cases where that's not the case
anymore (more about this in the next patch). Instead we need to be able
to specify custom GPIO base for certain pad groups.
To support this, add a new field (gpio_base) to the pad group structure
and update the core Intel pinctrl driver to handle this accordingly.
Passing 0 as gpio_base will use direct mapping so the existing drivers
do not need to be modified. Passing -1 excludes the whole pad group from
having GPIO mapping.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit a60eac3239f01838bdd34eaac8c486c4c6e84551) Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Mika Westerberg [Mon, 27 Nov 2017 13:54:42 +0000 (16:54 +0300)]
gpio / ACPI: Drop unnecessary ACPI GPIO to Linux GPIO translation
BugLink: http://bugs.launchpad.net/bugs/1751714
We added acpi_gpiochip_pin_to_gpio_offset() because there was a need to
translate from ACPI GpioIo/GpioInt number to Linux GPIO number in the
Cherryview pinctrl driver. This translation is necessary because
Cherryview has gaps in the pin list and the driver used continuous GPIO
number space in Linux side as follows:
created GPIO range 0->7 ==> INT33FF:03 PIN 0->7
created GPIO range 8->19 ==> INT33FF:03 PIN 15->26
created GPIO range 20->25 ==> INT33FF:03 PIN 30->35
created GPIO range 26->33 ==> INT33FF:03 PIN 45->52
created GPIO range 34->43 ==> INT33FF:03 PIN 60->69
created GPIO range 44->54 ==> INT33FF:03 PIN 75->85
For example when ACPI GpioInt resource refers to GPIO 81 (SDMMC3_CD_B)
we translate from pin 81 to the corresponding Linux GPIO number, which
is 50. This number is then used when the GPIO is accessed through gpiolib.
It turns out, this is not necessary at all. We can just pass 1:1 mapping
between Linux GPIO numbers and pin numbers (including gaps) and the
pinctrl core handles all the details automatically:
created GPIO range 0->7 ==> INT33FF:03 PIN 0->7
created GPIO range 15->26 ==> INT33FF:03 PIN 15->26
created GPIO range 30->35 ==> INT33FF:03 PIN 30->35
created GPIO range 45->52 ==> INT33FF:03 PIN 45->52
created GPIO range 60->69 ==> INT33FF:03 PIN 60->69
created GPIO range 75->85 ==> INT33FF:03 PIN 75->85
Here GPIO 81 is exactly same than the hardware pin 81 (SDMMC3_CD_B).
As an added bonus this simplifies both the ACPI GPIO core code and the
Cherryview pinctrl driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit 03c4749dd6c7ff948a0ce59a44a1b97c015353c2) Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
UBUNTU: [Config] USB_XHCI_DBGCAP=y for commit mainline dfba2174dc42.
BugLink: http://bugs.launchpad.net/bugs/1730832 Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Lu Baolu [Fri, 2 Mar 2018 19:42:03 +0000 (14:42 -0500)]
usb: xhci: Add DbC support in xHCI driver
BugLink: http://bugs.launchpad.net/bugs/1730832
xHCI compatible USB host controllers(i.e. super-speed USB3 controllers)
can be implemented with the Debug Capability(DbC). It presents a debug
device which is fully compliant with the USB framework and provides the
equivalent of a very high performance full-duplex serial link. The debug
capability operation model and registers interface are defined in 7.6.8
of the xHCI specification, revision 1.1.
The DbC debug device shares a root port with the xHCI host. By default,
the debug capability is disabled and the root port is assigned to xHCI.
When the DbC is enabled, the root port will be assigned to the DbC debug
device, and the xHCI sees nothing on this port. This implementation uses
a sysfs node named <dbc> under the xHCI device to manage the enabling
and disabling of the debug capability.
When the debug capability is enabled, it will present a debug device
through the debug port. This debug device is fully compliant with the
USB3 framework, and it can be enumerated by a debug host on the other
end of the USB link. As soon as the debug device is configured, a TTY
serial device named /dev/ttyDBC0 will be created.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(back ported from commit dfba2174dc421ecad8dc50741054a305cd3ba681) Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Lu Baolu [Fri, 2 Mar 2018 19:42:02 +0000 (14:42 -0500)]
usb: xhci: Make some static functions global
BugLink: http://bugs.launchpad.net/bugs/1730832
This patch makes some static functions global to avoid duplications
in different files. These functions can be used in the implementation
of xHCI debug capability. There is no functional change.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 67d2ea9fde2aa96f36af0537e4004efb123319fb) Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Aaron Ma [Mon, 5 Mar 2018 02:28:49 +0000 (10:28 +0800)]
platform/x86: ideapad-laptop: Increase timeout to wait for EC answer
BugLink: http://bugs.launchpad.net/bugs/1753347
Lenovo E41-20 needs more time than 100ms to read VPC,
the funtion keys always failed responding.
Increase timeout to get the value from VPC, then
the funtion keys like mic mute key work well.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
(cherry picked from commit ed5b9ba7bef7f277cbdf315e385b44e0e3b1a9ab) Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Acked-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Hui Wang [Sat, 3 Mar 2018 13:45:23 +0000 (21:45 +0800)]
ALSA: hda - Fix a wrong FIXUP for alc289 on Dell machines
BugLink: https://bugs.launchpad.net/bugs/1748807
With the alc289, the Pin 0x1b is Headphone-Mic, so we should assign
ALC269_FIXUP_DELL4_MIC_NO_PRESENCE rather than
ALC225_FIXUP_DELL1_MIC_NO_PRESENCE to it. And this change is suggested
by Kailang of Realtek and is verified on the machine.
Fixes: 3f2f7c553d07 ("ALSA: hda - Fix headset mic detection problem for two Dell machines") Cc: Kailang Yang <kailang@realtek.com> Cc: <stable@vger.kernel.org> Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
(cherry picked from commit d5078193e56bb24f4593f00102a3b5e07bb84ee0
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git) Signed-off-by: Hui Wang <hui.wang@canonical.com> Acked-by: Aaron Ma <aaron.ma@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Xiaofei Tan [Thu, 1 Mar 2018 20:44:44 +0000 (13:44 -0700)]
scsi: hisi_sas: directly attached disk LED feature for v2 hw
BugLink: https://bugs.launchpad.net/bugs/1752695
This patch implements LED feature of directly attached disk for v2 hw.
As libsas has provided an interface lldd_write_gpio() for this feature,
we just need realise the interface following SPGIO API.
We use an CPLD to finish the hardware part of this feature, and the base
address of CPLD should be configured through ACPI or DT tables.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(backported from commit 6379c56070b9ee32ae2b3efa51e121242042e72d)
[ dannf: trivial offset adjustment ] Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Mathias Nyman [Mon, 4 Dec 2017 12:05:45 +0000 (14:05 +0200)]
usb: Don't print a warning if interface driver rebind is deferred at resume
BugLink: https://bugs.launchpad.net/bugs/1730599
Interface drivers like btusb that don't support reset-resume will be
rebound at resume if port was reset. Rebind is done during the pm_ops
.complete callback when probe returns EPROBE_DEFER as default.
Remove the "rebind failed: -517" message.
Device probe will eventually take place later.
[one-liner by Jerry Snitselaar posted in a mailing list question -Mathias] Suggested-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit c0f3ed87fde812ee4511b650516f23e4bdf1642b) Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Tan Xiaojun [Thu, 1 Mar 2018 10:01:04 +0000 (21:01 +1100)]
drm/ttm: add ttm_bo_io_mem_pfn to check io_mem_pfn
BugLink: https://bugs.launchpad.net/bugs/1738334
The io_mem_pfn field was added in commit ea642c3216cb ("drm/ttm: add
io_mem_pfn callback") and is called unconditionally. However, not all
drivers were updated to set it.
Use the ttm_bo_default_io_mem_pfn function if a driver did not set its
own. And add new function ttm_bo_io_mem_pfn() as wrapper.
Signed-off-by: Michal Srb <msrb@suse.com> Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit c67fa6edc8b11afe22c88a23963170bf5f151acf) Signed-off-by: Daniel Axtens <daniel.axtens@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Seth Forshee [Wed, 28 Feb 2018 16:12:15 +0000 (10:12 -0600)]
UBUNTU: [Packaging] git-ubuntu-log -- fix detection of packaging changes
The recent update to handle multiple bugs/cves has an error in
the detection of packaging changes, causing them to be denoted as
upstream changes in the changelog. Change this logic to check the
subject field instead of the non-existent title field.
Ignore: yes Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Julian Wiedmann [Wed, 27 Dec 2017 16:44:31 +0000 (17:44 +0100)]
s390/qeth: support early setup for z/VM NICs
BugLink: http://bugs.launchpad.net/bugs/1747639
The transport mode that a z/VM NIC is configured in, must match the
hypervisor-internal network which the NIC is coupled to.
To get this right automatically, have qeth issue a diag26c hypervisor call
that provides all sorts of information for a specific VNIC.
With z/VM update VM65918, this also includes the VNIC's required
transport mode.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 615dff228368109ce18b628d6bd1b01ad6ef2f74) Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Building an allmodconfig kernel fails horribly because of
endian mismatch. It turns out that the -mlittle-endian
switch was not honored at all as we were using the wrong
Kconfig symbol and failing to apply CPUFLAGS to the CFLAGS.
Finally, the linker flags did not get set right.
This addresses all three of those issues, which now lets
me build both big-endian and little-endian kernels for
testing.
Fixes: 428dbf156cc5 ("arch: change default endian for microblaze") Fixes: 206d3642d8ee ("arch/microblaze: add choice for endianness and update Makefile") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
When a request is preempted, it is unsubmitted from the HW queue and
removed from the active list of breadcrumbs. In the process, this
however triggers the signaler and it may see the clear rbtree with the
old, and still valid, seqno, or it may match the cleared seqno with the
now zero rq->global_seqno. This confuses the signaler into action and
signaling the fence.
__show_regs pretty prints PC and LR by attempting to map them to kernel
function names to improve the utility of crash reports. Unfortunately,
this mapping is applied even when the pt_regs corresponds to user mode,
resulting in a KASLR oracle.
Avoid this issue by only looking up the function symbols when the register
state indicates that we're actually running at EL1.
Cc: <stable@vger.kernel.org> Reported-by: NCSC Security <security@ncsc.gov.uk> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Similar to the CPU address space the VA on Vega10 has a hole in it.
v2: use dev_dbg instead of dev_err
v3: add some more comments to explain how the hw works
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> CC: stable@vger.kernel.org Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
During eviction, the driver may free more than one hole in the drm_mm
due to the side-effects in evicting the scanned nodes. However,
drm_mm_scan_color_evict() expects that the scan result is the first
available hole (in the mru freed hole_stack list):
During a non-blocking commit, it is possible to return before the
commit_tail work is queued (-ERESTARTSYS, for example).
Since a reference on the crtc commit object is obtained for the pending
vblank event when preparing the commit, the above situation will leave
us with an extra reference.
Therefore, if the commit_tail worker has not consumed the event at the
end of a commit, release it's reference.
Changes since v1:
- Also check for state->event->base.completion being set, to
handle the case where stall_checks() fails in setup_crtc_commit().
Changes since v2:
- Add a flag to drm_crtc_commit, to prevent dereferencing a freed event.
i915 may unreference the state in a worker.
Fixes: 24835e442f28 ("drm: reference count event->completion") Cc: <stable@vger.kernel.org> # v4.11+ Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> #v1 Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180117115108.29608-1-maarten.lankhorst@linux.intel.com Reviewed-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
This fixes an issue that a gadget driver (usb_f_fs) is possible to
stop rx transactions after the usb-dmac is used because the following
functions missed to set/check the "running" flag.
- usbhsf_dma_prepare_pop_with_usb_dmac()
- usbhsf_dma_pop_done_with_usb_dmac()
So, if next transaction uses pio, the usbhsf_prepare_pop() can not
start the transaction because the "running" flag is 0.
Fixes: 8355b2b3082d ("usb: renesas_usbhs: fix the behavior of some usbhs_pkt_handle") Cc: <stable@vger.kernel.org> # v3.19+ Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
In commit 2bfa0719ac2a ("usb: gadget: function: f_fs: pass
companion descriptor along") there is a pointer arithmetic
bug where the comp_desc is obtained as follows:
Since ds is a pointer to usb_endpoint_descriptor, adding
7 to it ends up going out of bounds (7 * sizeof(struct
usb_endpoint_descriptor), which is actually 7*9 bytes) past
the SS descriptor. As a result the maxburst value will be
read incorrectly, and the UDC driver will also get a garbage
comp_desc (assuming it uses it).
Since Felipe wrote, "Eventually, f_fs.c should be converted
to use config_ep_by_speed() like all other functions, though",
let's finally do it. This allows the other usb_ep fields to
be properly populated, such as maxpacket and mult. It also
eliminates the awkward speed-based descriptor lookup since
config_ep_by_speed() does that already using the ones found
in struct usb_function.
Fixes: 2bfa0719ac2a ("usb: gadget: function: f_fs: pass companion descriptor along") Cc: stable@vger.kernel.org Signed-off-by: Jack Pham <jackp@codeaurora.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
During _ffs_func_bind(), the received descriptors are evaluated
to prepare for binding with the gadget in order to allocate
endpoints and optionally set up OS descriptors. However, the
high- and super-speed descriptors are only parsed based on
whether the gadget_is_dualspeed() and gadget_is_superspeed()
calls are true, respectively.
This is a problem in case a userspace program always provides
all of the {full,high,super,OS} descriptors when configuring a
function. Then, for example if a gadget device is not capable
of SuperSpeed, the call to ffs_do_descs() for the SS descriptors
is skipped, resulting in an incorrect offset calculation for
the vla_ptr when moving on to the OS descriptors that follow.
This causes ffs_do_os_descs() to fail as it is now looking at
the SS descriptors' offset within the raw_descs buffer instead.
_ffs_func_bind() should evaluate the descriptors unconditionally,
so remove the checks for gadget speed.
Fixes: f0175ab51993 ("usb: gadget: f_fs: OS descriptors support") Cc: stable@vger.kernel.org Co-Developed-by: Mayank Rana <mrana@codeaurora.org> Signed-off-by: Mayank Rana <mrana@codeaurora.org> Signed-off-by: Jack Pham <jackp@codeaurora.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
commit dbac5d07d13e ("usb: musb: host: don't start next rx urb if current one failed")
along with commit b5801212229f ("usb: musb: host: clear rxcsr error bit if set")
try to solve the issue described in [1], but the latter alone is
sufficient, and the former causes the issue as in [2], so now revert it.
Cc: stable@vger.kernel.org # v4.7+ Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Commit e93650994a95 ("usb: phy: mxs: add usb charger type detection")
causes the following kernel hang on i.MX28:
[ 2.207973] usbcore: registered new interface driver usb-storage
[ 2.235659] Unable to handle kernel NULL pointer dereference at virtual address 00000188
[ 2.244195] pgd = (ptrval)
[ 2.246994] [00000188] *pgd=00000000
[ 2.250676] Internal error: Oops: 5 [#1] ARM
[ 2.254979] Modules linked in:
[ 2.258089] CPU: 0 PID: 1 Comm: swapper Not tainted 4.15.0-rc8-next-20180117-00002-g75d5f21 #7
[ 2.266724] Hardware name: Freescale MXS (Device Tree)
[ 2.271921] PC is at regmap_read+0x0/0x5c
[ 2.275977] LR is at mxs_phy_charger_detect+0x34/0x1dc
mxs_phy_charger_detect() makes accesses to the anatop registers via regmap,
however i.MX23/28 do not have such registers, which causes a NULL pointer
dereference.
Fix the issue by doing a NULL check on the 'regmap' pointer.
Fixes: e93650994a95 ("usb: phy: mxs: add usb charger type detection") Cc: <stable@vger.kernel.org> # v4.15 Reviewed-by: Li Jun <jun.li@nxp.com> Acked-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
DWC3 tracks TRB counter for each ep0 direction separately. In control
read transfer completion handler, the driver needs to reset the TRB
enqueue counter for ep0 IN direction. Currently the driver only resets
the TRB counter for control OUT endpoint. Check for the data direction
and properly reset the TRB counter from correct control endpoint.
Cc: stable@vger.kernel.org Fixes: c2da2ff00606 ("usb: dwc3: ep0: don't use ep0in for transfers") Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
There are 2 control endpoint structures for DWC3. However, the driver
only updates the OUT direction control endpoint structure during
ConnectDone event. DWC3 driver needs to update the endpoint max packet
size for control IN endpoint as well. If the max packet size is not
properly set, then the driver will incorrectly calculate the data
transfer size and fail to send ZLP for HS/FS 3-stage control read
transfer.
The fix is simply to update the max packet size for the ep0 IN direction
during ConnectDone event.
Cc: stable@vger.kernel.org Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver") Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
commit a8c06e407ef9 ("usb: separate out sysdev pointer from usb_bus")
converted to use hcd->self.sysdev for DMA operations instead of
hcd->self.controller, but forgot to do it for hcd test mode. Replace
the correct one in this commit.
Fixes: a8c06e407ef9 ("usb: separate out sysdev pointer from usb_bus") Signed-off-by: Peter Chen <peter.chen@nxp.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Similar to commit e10aec652f31 ("drm/edid: Add 6 bpc quirk for display
AEO model 0."), the EDID reports "DFP 1.x compliant TMDS" but it support
6bpc instead of 8 bpc.
Hence, use 6 bpc quirk for this panel.
Fixes: 196f954e2509 ("drm/i915/dp: Revert "drm/i915/dp: fall back to 18 bpp when sink capability is unknown"") BugLink: https://bugs.launchpad.net/bugs/1749420 Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com> Cc: <stable@vger.kernel.org> # v4.8+ Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20180218085359.7817-1-kai.heng.feng@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.
Device ids found here:
usb 3-3: New USB device found, idVendor=1b1c, idProduct=1b13
usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-3: Product: Corsair K70 RGB Gaming Keyboard
Signed-off-by: Jack Stocker <jackstocker.93@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Stop printing a (ratelimited) kernel message for each instance of an
unimplemented syscall being called. Userland making an unimplemented
syscall is not necessarily misbehaviour and to be expected with a
current userland running on an older kernel. Also, the current message
looks scary to users but does not actually indicate a real problem nor
help them narrow down the cause. Just rely on sys_ni_syscall() to return
-ENOSYS.
Cc: <stable@vger.kernel.org> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Michael Weiser <michael.weiser@gmx.de> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
There is a race condition between finish_unlinks->finish_urb() function
and usb_kill_urb() in ohci controller case. The finish_urb calls
spin_unlock(&ohci->lock) before usb_hcd_giveback_urb() function call,
then if during this time, usb_kill_urb is called for another endpoint,
then new ed will be added to ed_rm_list at beginning for unlink, and
ed_rm_list will point to newly added.
When finish_urb() is completed in finish_unlinks() and ed->td_list
becomes empty as in below code (in finish_unlinks() function):
The *last = ed->ed_next will make ed_rm_list to point to ed->ed_next
and previously added ed by usb_kill_urb will be left unreferenced by
ed_rm_list. This causes usb_kill_urb() hang forever waiting for
finish_unlink to remove added ed from ed_rm_list.
The main reason for hang in this race condtion is addition and removal
of ed from ed_rm_list in the beginning during usb_kill_urb and later
last* is modified in finish_unlinks().
As suggested by Alan Stern, the solution for proper handling of
ohci->ed_rm_list is to remove ed from the ed_rm_list before finishing
any URBs. Then at the end, we can add ed back to the list if necessary.
This properly handle the updated ohci->ed_rm_list in usb_kill_urb().
Fixes: 977dcfdc6031 ("USB: OHCI: don't lose track of EDs when a controller dies") Acked-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Signed-off-by: Aman Deep <aman.deep@samsung.com> Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Running io_watchdog_func() while ohci_urb_enqueue() is running can
cause a race condition where ohci->prev_frame_no is corrupted and the
watchdog can mis-detect following error:
ohci-platform 664a0800.usb: frame counter not updating; disabled
ohci-platform 664a0800.usb: HC died; cleaning up
Specifically, following scenario causes a race condition:
1. ohci_urb_enqueue() calls spin_lock_irqsave(&ohci->lock, flags)
and enters the critical section
2. ohci_urb_enqueue() calls timer_pending(&ohci->io_watchdog) and it
returns false
3. ohci_urb_enqueue() sets ohci->prev_frame_no to a frame number
read by ohci_frame_no(ohci)
4. ohci_urb_enqueue() schedules io_watchdog_func() with mod_timer()
5. ohci_urb_enqueue() calls spin_unlock_irqrestore(&ohci->lock,
flags) and exits the critical section
6. Later, ohci_urb_enqueue() is called
7. ohci_urb_enqueue() calls spin_lock_irqsave(&ohci->lock, flags)
and enters the critical section
8. The timer scheduled on step 4 expires and io_watchdog_func() runs
9. io_watchdog_func() calls spin_lock_irqsave(&ohci->lock, flags)
and waits on it because ohci_urb_enqueue() is already in the
critical section on step 7
10. ohci_urb_enqueue() calls timer_pending(&ohci->io_watchdog) and it
returns false
11. ohci_urb_enqueue() sets ohci->prev_frame_no to new frame number
read by ohci_frame_no(ohci) because the frame number proceeded
between step 3 and 6
12. ohci_urb_enqueue() schedules io_watchdog_func() with mod_timer()
13. ohci_urb_enqueue() calls spin_unlock_irqrestore(&ohci->lock,
flags) and exits the critical section, then wake up
io_watchdog_func() which is waiting on step 9
14. io_watchdog_func() enters the critical section
15. io_watchdog_func() calls ohci_frame_no(ohci) and set frame_no
variable to the frame number
16. io_watchdog_func() compares frame_no and ohci->prev_frame_no
On step 16, because this calling of io_watchdog_func() is scheduled on
step 4, the frame number set in ohci->prev_frame_no is expected to the
number set on step 3. However, ohci->prev_frame_no is overwritten on
step 11. Because step 16 is executed soon after step 11, the frame
number might not proceed, so ohci->prev_frame_no must equals to
frame_no.
To address above scenario, this patch introduces a special sentinel
value IO_WATCHDOG_OFF and set this value to ohci->prev_frame_no when
the watchdog is not pending or running. When ohci_urb_enqueue()
schedules the watchdog (step 4 and 12 above), it compares
ohci->prev_frame_no to IO_WATCHDOG_OFF so that ohci->prev_frame_no is
not overwritten while io_watchdog_func() is running.
Signed-off-by: Shigeru Yoshida <Shigeru.Yoshida@windriver.com> Signed-off-by: Haiqing Bai <Haiqing.Bai@windriver.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The control channel calls registered callbacks when control messages
such as XDomain protocol messages are received. The control channel
handling is done in a worker running on system workqueue which means the
networking driver can't run tear down flow which includes sending
disconnect request and waiting for a reply in the same worker. Otherwise
reply is never received (as the work is already running) and the
operation times out.
To fix this run disconnect ThunderboltIP flow asynchronously once
ThunderboltIP logout message is received.
Fixes: e69b6c02b4c3 ("net: Add support for networking over Thunderbolt cable") Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
When suspending to mem or disk the Thunderbolt controller typically goes
down as well tearing down the connection automatically. However, when
suspend to idle is used this does not happen so we need to make sure the
connection is properly disconnected before it can be re-established
during resume.
Fixes: e69b6c02b4c3 ("net: Add support for networking over Thunderbolt cable") Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
We've run into a problem where our device is attached
to a Virtual Machine and the use of the new pci_set_vpd_size()
API doesn't help. The VM kernel has been informed that
the accesses are okay, but all of the actual VPD Capability
Accesses are trapped down into the KVM Hypervisor where it
goes ahead and imposes the silent denials.
The right idea is to follow the kernel.org
commit 1c7de2b4ff88 ("PCI: Enable access to non-standard VPD for
Chelsio devices (cxgb3)") which Alexey Kardashevskiy authored
to establish a PCI Quirk for our T3-based adapters. This commit
extends that PCI Quirk to cover Chelsio T4 devices and later.
The advantage of this approach is that the VPD Size gets set early
in the Base OS/Hypervisor Boot and doesn't require that the cxgb4
driver even be available in the Base OS/Hypervisor. Thus PF4 can
be exported to a Virtual Machine and everything should work.
Fixes: 67e658794ca1 ("cxgb4: Set VPD size so we can read both VPD structures") Cc: <stable@vger.kernel.org> # v4.9+ Signed-off-by: Casey Leedom <leedom@chelsio.com> Signed-off-by: Arjun Vynipadath <arjun@chelsio.com> Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Commit 7778c4b27cbe ("irqchip: mips-gic: Use pcpu_masks to avoid reading
GIC_SH_MASK*") removed the read of the hardware mask register when
handling shared interrupts, instead using the driver's shadow pcpu_masks
entry as the effective mask. Unfortunately this did not take account of
the write to pcpu_masks during gic_shared_irq_domain_map, which
effectively unmasks the interrupt early. If an interrupt is asserted,
gic_handle_shared_int decodes and processes the interrupt even though it
has not yet been unmasked via gic_unmask_irq, which also sets the
appropriate bit in pcpu_masks.
On the MIPS Boston board, when a console command line of
"console=ttyS0,115200n8r" is passed, the modem status IRQ is enabled in
the UART, which is immediately raised to the GIC. The interrupt has been
mapped, but no handler has yet been registered, nor is it expected to be
unmasked. However, the write to pcpu_masks in gic_shared_irq_domain_map
has effectively unmasked it, resulting in endless reports of:
To fix this, just remove the write to pcpu_masks in
gic_shared_irq_domain_map. The existing write in gic_unmask_irq is the
correct place for what is now the effective unmasking.
Cc: stable@vger.kernel.org Fixes: 7778c4b27cbe ("irqchip: mips-gic: Use pcpu_masks to avoid reading GIC_SH_MASK*") Signed-off-by: Matt Redfearn <matt.redfearn@mips.com> Reviewed-by: Paul Burton <paul.burton@mips.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
A DMB instruction can be used to ensure the relative order of only
memory accesses before and after the barrier. Since writes to system
registers are not memory operations, barrier DMB is not sufficient
for observability of memory accesses that occur before ICC_SGI1R_EL1
writes.
A DSB instruction ensures that no instructions that appear in program
order after the DSB instruction, can execute until the DSB instruction
has completed.
Cc: stable@vger.kernel.org Acked-by: Will Deacon <will.deacon@arm.com>, Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
This fixes a compile problem of some user space applications by not
including linux/libc-compat.h in uapi/if_ether.h.
linux/libc-compat.h checks which "features" the header files, included
from the libc, provide to make the Linux kernel uapi header files only
provide no conflicting structures and enums. If a user application mixes
kernel headers and libc headers it could happen that linux/libc-compat.h
gets included too early where not all other libc headers are included
yet. Then the linux/libc-compat.h would not prevent all the
redefinitions and we run into compile problems.
This patch removes the include of linux/libc-compat.h from
uapi/if_ether.h to fix the recently introduced case, but not all as this
is more or less impossible.
It is no problem to do the check directly in the if_ether.h file and not
in libc-compat.h as this does not need any fancy glibc header detection
as glibc never provided struct ethhdr and should define
__UAPI_DEF_ETHHDR by them self when they will provide this.
The following test program did not compile correctly any more:
Commit f7f99100d8d9 ("mm: stop zeroing memory during allocation in
vmemmap") broke Xen pv domains in some configurations, as the "Pinned"
information in struct page of early page tables could get lost.
This will lead to the kernel trying to write directly into the page
tables instead of asking the hypervisor to do so. The result is a crash
like the following:
Avoid this problem by not deferring struct page initialization when
running as Xen pv guest.
Pavel said:
: This is unique for Xen, so this particular issue won't effect other
: configurations. I am going to investigate if there is a way to
: re-enable deferred page initialization on xen guests.
[akpm@linux-foundation.org: explicitly include xen.h] Link: http://lkml.kernel.org/r/20180216154101.22865-1-jgross@suse.com Fixes: f7f99100d8d95d ("mm: stop zeroing memory during allocation in vmemmap") Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Pavel Tatashin <pasha.tatashin@oracle.com> Cc: Steven Sistare <steven.sistare@oracle.com> Cc: Daniel Jordan <daniel.m.jordan@oracle.com> Cc: Bob Picco <bob.picco@oracle.com> Cc: <stable@vger.kernel.org> [4.15.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
It was reported by Sergey Senozhatsky that if THP (Transparent Huge
Page) and frontswap (via zswap) are both enabled, when memory goes low
so that swap is triggered, segfault and memory corruption will occur in
random user space applications as follow,
After bisection, it was found the first bad commit is bd4c82c22c36 ("mm,
THP, swap: delay splitting THP after swapped out").
The root cause is as follows:
When the pages are written to swap device during swapping out in
swap_writepage(), zswap (fontswap) is tried to compress the pages to
improve performance. But zswap (frontswap) will treat THP as a normal
page, so only the head page is saved. After swapping in, tail pages
will not be restored to their original contents, causing memory
corruption in the applications.
This is fixed by refusing to save page in the frontswap store functions
if the page is a THP. So that the THP will be swapped out to swap
device.
Another choice is to split THP if frontswap is enabled. But it is found
that the frontswap enabling isn't flexible. For example, if
CONFIG_ZSWAP=y (cannot be module), frontswap will be enabled even if
zswap itself isn't enabled.
Frontswap has multiple backends, to make it easy for one backend to
enable THP support, the THP checking is put in backend frontswap store
functions instead of the general interfaces.
Link: http://lkml.kernel.org/r/20180209084947.22749-1-ying.huang@intel.com Fixes: bd4c82c22c367e068 ("mm, THP, swap: delay splitting THP after swapped out") Signed-off-by: "Huang, Ying" <ying.huang@intel.com> Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Suggested-by: Minchan Kim <minchan@kernel.org> [put THP checking in backend] Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Dan Streetman <ddstreet@ieee.org> Cc: Seth Jennings <sjenning@redhat.com> Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: Shaohua Li <shli@kernel.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Shakeel Butt <shakeelb@google.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Juergen Gross <jgross@suse.com> Cc: <stable@vger.kernel.org> [4.14] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
GCC-8 shows a warning for the x86 oprofile code that copies per-CPU
data from CPU 0 to all other CPUs, which when building a non-SMP
kernel turns into a memcpy() with identical source and destination
pointers:
arch/x86/oprofile/nmi_int.c: In function 'mux_clone':
arch/x86/oprofile/nmi_int.c:285:2: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
memcpy(per_cpu(cpu_msrs, cpu).multiplex,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
per_cpu(cpu_msrs, 0).multiplex,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(struct op_msr) * model->num_virt_counters);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/x86/oprofile/nmi_int.c: In function 'nmi_setup':
arch/x86/oprofile/nmi_int.c:466:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
arch/x86/oprofile/nmi_int.c:470:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
I have analyzed a number of such warnings now: some are valid and the
GCC warning is welcome. Others turned out to be false-positives, and
GCC was changed to not warn about those any more. This is a corner case
that is a false-positive but the GCC developers feel it's better to keep
warning about it.
In this case, it seems best to work around it by telling GCC
a little more clearly that this code path is never hit with
an IS_ENABLED() configuration check.
Cc:stable as we also want old kernels to build cleanly with GCC-8.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Jessica Yu <jeyu@kernel.org> Cc: Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Martin Sebor <msebor@gcc.gnu.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Robert Richter <rric@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: oprofile-list@lists.sf.net Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/20180220205826.2008875-1-arnd@arndb.de Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=84095 Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
When a irq vector is replaced, then the previous vector is normally
released when the first interrupt happens on the new vector. If the target
CPU of the previous vector is already offline when the new vector is
installed, then the previous vector is silently discarded, which leads to
accounting issues causing suspend failures and other problems.
Adjust the logic so that the previous vector is freed in the underlying
matrix allocator to ensure that the accounting stays correct.
Fixes: 69cde0004a4b ("x86/vector: Use matrix allocator for vector assignment") Reported-by: Yuriy Vostrikov <delamonpansie@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Yuriy Vostrikov <delamonpansie@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180222112316.930791749@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Build testing with LTO found a couple of files that get compiled
differently depending on whether asm/byteorder.h gets included early
enough or not. In particular, include/asm-generic/qrwlock_types.h is
affected by this, but there are probably others as well.
The symptom is a series of LTO link time warnings, including these:
net/netlabel/netlabel_unlabeled.h:223: error: type of 'netlbl_unlhsh_add' does not match original declaration [-Werror=lto-type-mismatch]
int netlbl_unlhsh_add(struct net *net,
net/netlabel/netlabel_unlabeled.c:377: note: 'netlbl_unlhsh_add' was previously declared here
include/net/ipv6.h:360: error: type of 'ipv6_renew_options_kern' does not match original declaration [-Werror=lto-type-mismatch]
ipv6_renew_options_kern(struct sock *sk,
net/ipv6/exthdrs.c:1162: note: 'ipv6_renew_options_kern' was previously declared here
net/core/dev.c:761: note: 'dev_get_by_name_rcu' was previously declared here
struct net_device *dev_get_by_name_rcu(struct net *net, const char *name)
net/core/dev.c:761: note: code may be misoptimized unless -fno-strict-aliasing is used
drivers/gpu/drm/i915/i915_drv.h:3377: error: type of 'i915_gem_object_set_to_wc_domain' does not match original declaration [-Werror=lto-type-mismatch]
i915_gem_object_set_to_wc_domain(struct drm_i915_gem_object *obj, bool write);
drivers/gpu/drm/i915/i915_gem.c:3639: note: 'i915_gem_object_set_to_wc_domain' was previously declared here
include/linux/debugfs.h:92:9: error: type of 'debugfs_attr_read' does not match original declaration [-Werror=lto-type-mismatch]
ssize_t debugfs_attr_read(struct file *file, char __user *buf,
fs/debugfs/file.c:318: note: 'debugfs_attr_read' was previously declared here
include/linux/rwlock_api_smp.h:30: error: type of '_raw_read_unlock' does not match original declaration [-Werror=lto-type-mismatch]
void __lockfunc _raw_read_unlock(rwlock_t *lock) __releases(lock);
kernel/locking/spinlock.c:246:26: note: '_raw_read_unlock' was previously declared here
include/linux/fs.h:3308:5: error: type of 'simple_attr_open' does not match original declaration [-Werror=lto-type-mismatch]
int simple_attr_open(struct inode *inode, struct file *file,
fs/libfs.c:795: note: 'simple_attr_open' was previously declared here
All of the above are caused by include/asm-generic/qrwlock_types.h
failing to include asm/byteorder.h after commit e0d02285f16e
("locking/qrwlock: Use 'struct qrwlock' instead of 'struct __qrwlock'")
in linux-4.15.
Similar bugs may or may not exist in older kernels as well, but there is
no easy way to test those with link-time optimizations, and kernels
before 4.14 are harder to fix because they don't have Babu's patch
series
We had similar issues with CONFIG_ symbols in the past and ended up
always including the configuration headers though linux/kconfig.h. This
works around the issue through that same file, defining either
__BIG_ENDIAN or __LITTLE_ENDIAN depending on CONFIG_CPU_BIG_ENDIAN,
which is now always set on all architectures since commit 4c97a0c8fee3
("arch: define CPU_BIG_ENDIAN for all fixed big endian archs").
Link: http://lkml.kernel.org/r/20180202154104.1522809-2-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Babu Moger <babu.moger@amd.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Nicolas Pitre <nico@linaro.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The adis_probe_trigger() creates a new IIO trigger and requests an
interrupt associated with the trigger. The interrupt uses the generic
iio_trigger_generic_data_rdy_poll() function as its interrupt handler.
Currently the driver initializes some fields of the trigger structure after
the interrupt has been requested. But an interrupt can fire as soon as it
has been requested. This opens up a race condition.
iio_trigger_generic_data_rdy_poll() will access the trigger data structure
and dereference the ops field. If the ops field is not yet initialized this
will result in a NULL pointer deref.
It is not expected that the device generates an interrupt at this point, so
typically this issue did not surface unless e.g. due to a hardware
misconfiguration (wrong interrupt number, wrong polarity, etc.).
But some newer devices from the ADIS family start to generate periodic
interrupts in their power-on reset configuration and unfortunately the
interrupt can not be masked in the device. This makes the race condition
much more visible and the following crash has been observed occasionally
when booting a system using the ADIS16460.
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = c0004000
[00000008] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.9.0-04126-gf9739f0-dirty #257
Hardware name: Xilinx Zynq Platform
task: ef04f640 task.stack: ef050000
PC is at iio_trigger_notify_done+0x30/0x68
LR is at iio_trigger_generic_data_rdy_poll+0x18/0x20
pc : [<c042d868>] lr : [<c042d924>] psr: 60000193
sp : ef051bb8 ip : 00000000 fp : ef106400
r10: c081d80a r9 : ef3bfa00 r8 : 00000087
r7 : ef051bec r6 : 00000000 r5 : ef3bfa00 r4 : ee92ab00
r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : ee97e400
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment none
Control: 18c5387d Table: 0000404a DAC: 00000051
Process swapper/0 (pid: 1, stack limit = 0xef050210)
[<c042d868>] (iio_trigger_notify_done) from [<c0065b10>] (__handle_irq_event_percpu+0x88/0x118)
[<c0065b10>] (__handle_irq_event_percpu) from [<c0065bbc>] (handle_irq_event_percpu+0x1c/0x58)
[<c0065bbc>] (handle_irq_event_percpu) from [<c0065c30>] (handle_irq_event+0x38/0x5c)
[<c0065c30>] (handle_irq_event) from [<c0068e28>] (handle_level_irq+0xa4/0x130)
[<c0068e28>] (handle_level_irq) from [<c0064e74>] (generic_handle_irq+0x24/0x34)
[<c0064e74>] (generic_handle_irq) from [<c021ab7c>] (zynq_gpio_irqhandler+0xb8/0x13c)
[<c021ab7c>] (zynq_gpio_irqhandler) from [<c0064e74>] (generic_handle_irq+0x24/0x34)
[<c0064e74>] (generic_handle_irq) from [<c0065370>] (__handle_domain_irq+0x5c/0xb4)
[<c0065370>] (__handle_domain_irq) from [<c000940c>] (gic_handle_irq+0x48/0x8c)
[<c000940c>] (gic_handle_irq) from [<c0013e8c>] (__irq_svc+0x6c/0xa8)
To fix this make sure that the trigger is fully initialized before
requesting the interrupt.
Fixes: ccd2b52f4ac6 ("staging:iio: Add common ADIS library") Reported-by: Robin Getz <Robin.Getz@analog.com> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
If no iio buffer has been set up and poll is called return 0.
Without this check there will be a null pointer dereference when
calling poll on a iio driver without an iio buffer.
Cc: stable@vger.kernel.org Signed-off-by: Stefan Windfeldt-Prytz <stefan.windfeldt@axis.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Functions for triggered buffer support are needed by this module.
If they are not defined accidentally by another driver, there's an error
thrown out while linking.
Add a select of IIO_BUFFER and IIO_TRIGGERED_BUFFER in the Kconfig file.
Signed-off-by: Andreas Klinger <ak@it-klinger.de> Fixes: a83195937151 ("iio: srf08: add triggered buffer support") Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Error handling in stm32h7_adc_enable routine doesn't unwind enable
sequence correctly. ADEN can only be cleared by hardware (e.g. by
writing one to ADDIS).
It's also better to clear ADRDY just after it's been set by hardware.
Fixes: 95e339b6e85d ("iio: adc: stm32: add support for STM32H7") Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
==================================================================
BUG: KASAN: use-after-free in copy_ah_attr_from_uverbs+0x6f2/0x8c0
Read of size 4 at addr ffff88006476a198 by task syzkaller697701/265
There is no matching lock for this mutex. Git history suggests this is
just a missed remnant from an earlier version of the function before
this locking was moved into uverbs_free_xrcd.
Originally this lock was protecting the xrcd_table_delete()
=====================================
WARNING: bad unlock balance detected!
4.15.0+ #87 Not tainted
-------------------------------------
syzkaller223405/269 is trying to release lock (&uverbs_dev->xrcd_tree_mutex) at:
[<00000000b8703372>] ib_uverbs_close_xrcd+0x195/0x1f0
but there are no more locks to release!
other info that might help us debug this:
1 lock held by syzkaller223405/269:
#0: (&uverbs_dev->disassociate_srcu){....}, at: [<000000005af3b960>] ib_uverbs_write+0x265/0xef0
The command number is not bounds checked against the command mask before it
is shifted, resulting in an ubsan hit. This does not cause malfunction since
the command number is eventually bounds checked, but we can make this ubsan
clean by moving the bounds check to before the mask check.
The race is between lookup_get_idr_uobject and
uverbs_idr_remove_uobj -> uverbs_uobject_put.
We deliberately do not call sychronize_rcu after the idr_remove in
uverbs_idr_remove_uobj for performance reasons, instead we call
kfree_rcu() during uverbs_uobject_put.
However, this means we can obtain pointers to uobj's that have
already been released and must protect against krefing them
using kref_get_unless_zero.
==================================================================
BUG: KASAN: use-after-free in copy_ah_attr_from_uverbs.isra.2+0x860/0xa00
Read of size 4 at addr ffff88005fda1ac8 by task syz-executor2/441
Memory state around the buggy address: ffff88005fda1980: fc fc fb fb fb fb fc fc fb fb fb fb fc fc fb fb ffff88005fda1a00: fb fb fc fc fb fb fb fb fc fc 00 00 00 00 fc fc ffff88005fda1a80: fb fb fb fb fc fc fb fb fb fb fc fc fb fb fb fb ffff88005fda1b00: fc fc 00 00 00 00 fc fc fb fb fb fb fc fc fb fb ffff88005fda1b80: fb fb fc fc fb fb fb fb fc fc fb fb fb fb fc fc
==================================================================@
Cc: syzkaller <syzkaller@googlegroups.com> Cc: <stable@vger.kernel.org> # 4.11 Fixes: 3832125624b7 ("IB/core: Add support for idr types") Reported-by: Noa Osherovich <noaos@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
At CPU hotunplug the corresponding per cpu matrix allocator is shut down and
the allocated interrupt bits are discarded under the assumption that all
allocated bits have been either migrated away or shut down through the
managed interrupts mechanism.
This is not true because interrupts which are not started up might have a
vector allocated on the outgoing CPU. When the interrupt is started up
later or completely shutdown and freed then the allocated vector is handed
back, triggering warnings or causing accounting issues which result in
suspend failures and other issues.
Change the CPU hotplug mechanism of the matrix allocator so that the
remaining allocations at unplug time are preserved and global accounting at
hotplug is correctly readjusted to take the dormant vectors into account.
Fixes: 2f75d9e1c905 ("genirq: Implement bitmap matrix allocator") Reported-by: Yuriy Vostrikov <delamonpansie@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Yuriy Vostrikov <delamonpansie@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180222112316.849980972@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Some other drivers may be waiting for our extcon to show-up, exiting their
probe methods with -EPROBE_DEFER until we show up.
These drivers will typically get the cable state directly after getting
the extcon, this commit changes the int3496 code to wait for the initial
processing of the id-pin to complete before exiting probe() with 0, which
will cause devices waiting on the defered probe to get reprobed.
This fixes a race where the initial work might still be running while other
drivers were already calling extcon_get_state().
Fixes: 2f556bdb9f2e ("extcon: int3496: Add Intel INT3496 ACPI ... driver") Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>