Jeeja KP [Fri, 18 Dec 2015 09:42:08 +0000 (15:12 +0530)]
ASoC: Intel: Skylake: Reconfigure Link stream on suspend/resume
On suspend the link register are lost so we need to reconfigure
them in resume. This patch adds the reconfiguration of the link
register in trigger resume.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Jeeja KP [Fri, 18 Dec 2015 09:42:07 +0000 (15:12 +0530)]
ASoC: Intel: Skylake: Add DMA resume position in Trigger resume/suspend
Use the DMA resume capability to resume the DMA position when
stream is suspended/resumed.
In suspend we save the position and when stream is resumed the stream needs
to be started from the position when the stream was suspended using the new
DMA resume capabilities
Signed-off-by: Jeeja KP <jeeja.kp@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Jeeja KP [Fri, 18 Dec 2015 09:42:06 +0000 (15:12 +0530)]
ASoC: Intel: Skylake: enable interrupt as wake source in active suspend
In active suspend, any HDA interrupt should wake the system. When device
enters active suspend, we need to enable HDA controller interrupt as wake
source. Similarly disable HDA controller interrupt as wake source when
exiting active suspend.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Vinod Koul [Fri, 18 Dec 2015 09:42:05 +0000 (15:12 +0530)]
ASoC: Intel: Skylake: manage link power in active suspend
When device enters active suspend, we should turn off the links
as they are not in use. Similarly we need to bring back links
when we exit active suspend.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com> Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Dharageswari.R [Fri, 18 Dec 2015 09:42:04 +0000 (15:12 +0530)]
ASoC: Intel: Skylake: Use CGCTL.MISCBDCGE for Phrase detection notification
Per HW recommendation, SW shall clear the CGCTL.MISCBDCGE and set
it back once data is transferred. So clear this when we get the
IPC and track using a driver flag, and set back on closure
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com> Signed-off-by: Jayachandran B <jayachandran.b@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
MISCBDCGE is a new register for Misc Backbone clock gate control
which is useful to control while resetting the link and ensuring
controller is in required state so add API to control it
HW recommends that we reset with CGCTL.MISCBDCGE disabled, so add
that while doing init chip and reset sequence.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Jeeja KP [Fri, 18 Dec 2015 09:42:00 +0000 (15:12 +0530)]
ALSA: hdac: couple the hda DMA stream in cleanup
A stream is by default in coupled mode, in DSP operation we move
it to decoupled mode. On cleanup HW expects that we leave it back
to default state so couple the DMA on cleanup.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Reviewed-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Mark Brown <broonie@kernel.org>
Jeeja KP [Fri, 18 Dec 2015 09:41:59 +0000 (15:11 +0530)]
ALSA: hdac: Add support for hda DMA Resume capability
Skylake sports new capability of DMA resume, DRSM where we can
resume the DMA. This capability is defined by presence of
AZX_DRSM_CAP_ID.
If this capability is present, we use this capability.
So we add:
snd_hdac_ext_stream_drsm_enable() - DMA resume caps
snd_hdac_ext_stream_set_dpibr() - set the DMA position
snd_hdac_ext_stream_set_lpib() - set the lpib
Signed-off-by: Jeeja KP <jeeja.kp@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Reviewed-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: hdac_hdmi: Use list to add pins and converters
Future platforms may have a different set of pins/converters.
So use lists to add pins and converters based on enumeration.
Also it may be required to connect any converter to any pin
dynamically as per different use cases (for example DP is
connected to pin 6 on skylake board). So this will help in
dynamically select and route.
Fix the dai map as well to use the pin/cvt from list. Not
enabling all dai maps for now.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: hdac_hdmi: Fix to warn instead of err for no connected nids
It is possible that some pin widget may return with no converter
connected. So don't throw error if none are found to be connected.
Instead print a warning and continue.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
commit 3c83ac23253c ("ASoC: hdac_hdmi: check error return") fixes
the static checker warning reported by Dan Carpenter:
sound/soc/codecs/hdac_hdmi.c:416 hdac_hdmi_parse_and_map_nid()
warn: unsigned 'hdac->num_nodes' is never less than zero.
But it doesn't fix the issue completely.
It's also a failure if no sub nodes found for an afg node. So modify
the return condition appropriately.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
The machine driver is not loaded when the BIOS uses the 10EC5642
_HID. Add it to the white list of known _HIDs, codec_name is
already taken care of by previous commit
Tested on Asus T100TAF.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Jack Yu [Mon, 4 Jan 2016 23:20:26 +0000 (17:20 -0600)]
ASoC: rt5640: add ASRC support
Signed-off-by: Jack Yu <jack.yu@realtek.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
The SKL drivers can be deferred probe. The topology file based widgets can
have references to topology file so this can't be freed until card is fully
created, so revert this patch for now
Linus Torvalds [Sun, 3 Jan 2016 19:49:31 +0000 (11:49 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS build fix from Ralf Baechle:
"Fix a makefile issue resulting in build breakage with older binutils.
This has sat in -next for a few days, testers and buildbot are happy
with it, too though if you are going for another -rc that'd certainly
help ironing out a few more issues"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: VDSO: Fix build error with binutils 2.24 and earlier
Linus Torvalds [Sun, 3 Jan 2016 19:36:26 +0000 (11:36 -0800)]
Merge tag 'drm-intel-fixes-2016-01-02' of git://anongit.freedesktop.org/drm-intel
Pull i915 drm fixes from Jani Nikula:
"Two display fixes still for v4.4.
The new year's resolution is to start using signed tags per Linus'
request. This one is still unsigned; I want to fix this up in our
maintainer scripts instead of doing it one-off"
* tag 'drm-intel-fixes-2016-01-02' of git://anongit.freedesktop.org/drm-intel:
drm/i915: increase the tries for HDMI hotplug live status checking
drm/i915: Unbreak check_digital_port_conflicts()
Linus Torvalds [Thu, 31 Dec 2015 22:59:21 +0000 (14:59 -0800)]
Merge tag 'pci-v4.4-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI bugfix from Bjorn Helgaas:
"Here's another fix for v4.4.
This fixes 32-bit config reads for the HiSilicon driver. Obviously
the driver is completely broken without this fix (apparently it
actually was tested internally, but got broken somehow in the process
of upstreaming it).
Xin Long [Tue, 29 Dec 2015 09:49:25 +0000 (17:49 +0800)]
sctp: sctp should release assoc when sctp_make_abort_user return NULL in sctp_close
In sctp_close, sctp_make_abort_user may return NULL because of memory
allocation failure. If this happens, it will bypass any state change
and never free the assoc. The assoc has no chance to be freed and it
will be kept in memory with the state it had even after the socket is
closed by sctp_close().
So if sctp_make_abort_user fails to allocate memory, we should abort
the asoc via sctp_primitive_ABORT as well. Just like the annotation in
sctp_sf_cookie_wait_prm_abort and sctp_sf_do_9_1_prm_abort said,
"Even if we can't send the ABORT due to low memory delete the TCB.
This is a departure from our typical NOMEM handling".
But then the chunk is NULL (low memory) and the SCTP_CMD_REPLY cmd would
dereference the chunk pointer, and system crash. So we should add
SCTP_CMD_REPLY cmd only when the chunk is not NULL, just like other
places where it adds SCTP_CMD_REPLY cmd.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolai Stange [Tue, 29 Dec 2015 12:29:55 +0000 (13:29 +0100)]
net, socket, socket_wq: fix missing initialization of flags
Commit ceb5d58b2170 ("net: fix sock_wake_async() rcu protection") from
the current 4.4 release cycle introduced a new flags member in
struct socket_wq and moved SOCKWQ_ASYNC_NOSPACE and SOCKWQ_ASYNC_WAITDATA
from struct socket's flags member into that new place.
Unfortunately, the new flags field is never initialized properly, at least
not for the struct socket_wq instance created in sock_alloc_inode().
One particular issue I encountered because of this is that my GNU Emacs
failed to draw anything on my desktop -- i.e. what I got is a transparent
window, including the title bar. Bisection lead to the commit mentioned
above and further investigation by means of strace told me that Emacs
is indeed speaking to my Xorg through an O_ASYNC AF_UNIX socket. This is
reproducible 100% of times and the fact that properly initializing the
struct socket_wq ->flags fixes the issue leads me to the conclusion that
somehow SOCKWQ_ASYNC_WAITDATA got set in the uninitialized ->flags,
preventing my Emacs from receiving any SIGIO's due to data becoming
available and it got stuck.
Make sock_alloc_inode() set the newly created struct socket_wq's ->flags
member to zero.
Fixes: ceb5d58b2170 ("net: fix sock_wake_async() rcu protection") Signed-off-by: Nicolai Stange <nicstange@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 30 Dec 2015 18:26:20 +0000 (10:26 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Make the block layer great again.
Basically three amazing fixes in this pull request, split into 4
patches. Believe me, they should go into 4.4. Two of them fix a
regression, the third and last fixes an easy-to-trigger bug.
- Fix a bad irq enable through null_blk, for queue_mode=1 and using
timer completions. Add a block helper to restart a queue
asynchronously, and use that from null_blk. From me.
- Fix a performance issue in NVMe. Some devices (Intel Pxxxx) expose
a stripe boundary, and performance suffers if we cross it. We took
that into account for merging, but not for the newer splitting
code. Fix from Keith.
- Fix a kernel oops in lightnvm with multiple channels. From Matias"
* 'for-linus' of git://git.kernel.dk/linux-block:
lightnvm: wrong offset in bad blk lun calculation
null_blk: use async queue restart helper
block: add blk_start_queue_async()
block: Split bios on chunk boundaries
It looks like 70-80 ms is BSW platform needs in some bad cases of the
monitors at this end (8 times delay at most). Keep less than 100ms for
HDCP pulse HPD low (with at least 100ms) to respond a plug out.
Reviewed-by: Cooper Chiou <cooper.chiou@intel.com> Tested-by: Gary Wang <gary.c.wang@intel.com> Cc: Gavin Hindman <gavin.hindman@intel.com> Cc: Sonika Jindal <sonika.jindal@intel.com> Cc: Shashank Sharma <shashank.sharma@intel.com> Cc: Shobhit Kumar <shobhit.kumar@intel.com> Signed-off-by: Gary Wang <gary.c.wang@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1450858295-12804-1-git-send-email-gary.c.wang@intel.com Tested-by: Shobhit Kumar <shobhit.kumar@intel.com> Cc: drm-intel-fixes@lists.freedesktop.org Fixes: 237ed86c693d ("drm/i915: Check live status before reading edid") Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit f8d03ea0053b23de42c828d559016eabe0b91523)
[Jani: undo the file mode change of the original commit] Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Linus Torvalds [Wed, 30 Dec 2015 02:04:41 +0000 (18:04 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"9 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/vmstat: fix overflow in mod_zone_page_state()
ocfs2/dlm: clear migration_pending when migration target goes down
mm/memory_hotplug.c: check for missing sections in test_pages_in_a_zone()
ocfs2: fix flock panic issue
m32r: add io*_rep helpers
m32r: fix build failure
arch/x86/xen/suspend.c: include xen/xen.h
mm: memcontrol: fix possible memcg leak due to interrupted reclaim
ocfs2: fix BUG when calculate new backup super
Heiko Carstens [Tue, 29 Dec 2015 22:54:32 +0000 (14:54 -0800)]
mm/vmstat: fix overflow in mod_zone_page_state()
mod_zone_page_state() takes a "delta" integer argument. delta contains
the number of pages that should be added or subtracted from a struct
zone's vm_stat field.
If a zone is larger than 8TB this will cause overflows. E.g. for a
zone with a size slightly larger than 8TB the line
in mm/page_alloc.c:free_area_init_core() will result in a negative
result for the NR_ALLOC_BATCH entry within the zone's vm_stat, since 8TB
contain 0x8xxxxxxx pages which will be sign extended to a negative
value.
Fix this by changing the delta argument to long type.
This could fix an early boot problem seen on s390, where we have a 9TB
system with only one node. ZONE_DMA contains 2GB and ZONE_NORMAL the
rest. The system is trying to allocate a GFP_DMA page but ZONE_DMA is
completely empty, so it tries to reclaim pages in an endless loop.
This was seen on a heavily patched 3.10 kernel. One possible
explaination seem to be the overflows caused by mod_zone_page_state().
Unfortunately I did not have the chance to verify that this patch
actually fixes the problem, since I don't have access to the system
right now. However the overflow problem does exist anyway.
Given the description that a system with slightly less than 8TB does
work, this seems to be a candidate for the observed problem.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Christoph Lameter <cl@linux.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
xuejiufei [Tue, 29 Dec 2015 22:54:29 +0000 (14:54 -0800)]
ocfs2/dlm: clear migration_pending when migration target goes down
We have found a BUG on res->migration_pending when migrating lock
resources. The situation is as follows.
dlm_mark_lockres_migration
res->migration_pending = 1;
__dlm_lockres_reserve_ast
dlm_lockres_release_ast returns with res->migration_pending remains
because other threads reserve asts
wait dlm_migration_can_proceed returns 1
>>>>>>> o2hb found that target goes down and remove target
from domain_map
dlm_migration_can_proceed returns 1
dlm_mark_lockres_migrating returns -ESHOTDOWN with
res->migration_pending still remains.
When reentering dlm_mark_lockres_migrating(), it will trigger the BUG_ON
with res->migration_pending. So clear migration_pending when target is
down.
Signed-off-by: Jiufei Xue <xuejiufei@huawei.com> Reviewed-by: Joseph Qi <joseph.qi@huawei.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Banman [Tue, 29 Dec 2015 22:54:25 +0000 (14:54 -0800)]
mm/memory_hotplug.c: check for missing sections in test_pages_in_a_zone()
test_pages_in_a_zone() does not account for the possibility of missing
sections in the given pfn range. pfn_valid_within always returns 1 when
CONFIG_HOLES_IN_ZONE is not set, allowing invalid pfns from missing
sections to pass the test, leading to a kernel oops.
Wrap an additional pfn loop with PAGES_PER_SECTION granularity to check
for missing sections before proceeding into the zone-check code.
This also prevents a crash from offlining memory devices with missing
sections. Despite this, it may be a good idea to keep the related patch
'[PATCH 3/3] drivers: memory: prohibit offlining of memory blocks with
missing sections' because missing sections in a memory block may lead to
other problems not covered by the scope of this fix.
Signed-off-by: Andrew Banman <abanman@sgi.com> Acked-by: Alex Thorlton <athorlton@sgi.com> Cc: Russ Anderson <rja@sgi.com> Cc: Alex Thorlton <athorlton@sgi.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Greg KH <greg@kroah.com> Cc: Seth Jennings <sjennings@variantweb.net> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Junxiao Bi [Tue, 29 Dec 2015 22:54:22 +0000 (14:54 -0800)]
ocfs2: fix flock panic issue
Commit 4f6563677ae8 ("Move locks API users to locks_lock_inode_wait()")
move flock/posix lock indentify code to locks_lock_inode_wait(), but
missed to set fl_flags to FL_FLOCK which caused the following kernel
panic on 4.4.0_rc5.
Fixes: 4f6563677ae8 ("Move locks API users to locks_lock_inode_wait()") Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Joseph Qi <joseph.qi@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sudip Mukherjee [Tue, 29 Dec 2015 22:54:16 +0000 (14:54 -0800)]
m32r: fix build failure
m32r allmodconfig is failing with:
In file included from ../include/linux/kvm_para.h:4:0,
from ../kernel/watchdog.c:26:
../include/uapi/linux/kvm_para.h:30:26: fatal error: asm/kvm_para.h: No such file or directory
Andrew Morton [Tue, 29 Dec 2015 22:54:13 +0000 (14:54 -0800)]
arch/x86/xen/suspend.c: include xen/xen.h
Fix the build warning:
arch/x86/xen/suspend.c: In function 'xen_arch_pre_suspend':
arch/x86/xen/suspend.c:70:9: error: implicit declaration of function 'xen_pv_domain' [-Werror=implicit-function-declaration]
if (xen_pv_domain())
^
Reported-by: kbuild test robot <fengguang.wu@intel.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vladimir Davydov [Tue, 29 Dec 2015 22:54:10 +0000 (14:54 -0800)]
mm: memcontrol: fix possible memcg leak due to interrupted reclaim
Memory cgroup reclaim can be interrupted with mem_cgroup_iter_break()
once enough pages have been reclaimed, in which case, in contrast to a
full round-trip over a cgroup sub-tree, the current position stored in
mem_cgroup_reclaim_iter of the target cgroup does not get invalidated
and so is left holding the reference to the last scanned cgroup. If the
target cgroup does not get scanned again (we might have just reclaimed
the last page or all processes might exit and free their memory
voluntary), we will leak it, because there is nobody to put the
reference held by the iterator.
The problem is easy to reproduce by running the following command
sequence in a loop:
mkdir /sys/fs/cgroup/memory/test
echo 100M > /sys/fs/cgroup/memory/test/memory.limit_in_bytes
echo $$ > /sys/fs/cgroup/memory/test/cgroup.procs
memhog 150M
echo $$ > /sys/fs/cgroup/memory/cgroup.procs
rmdir test
The cgroups generated by it will never get freed.
This patch fixes this issue by making mem_cgroup_iter avoid taking
reference to the current position. In order not to hit use-after-free
bug while running reclaim in parallel with cgroup deletion, we make use
of ->css_released cgroup callback to clear references to the dying
cgroup in all reclaim iterators that might refer to it. This callback
is called right before scheduling rcu work which will free css, so if we
access iter->position from rcu read section, we might be sure it won't
go away under us.
[hannes@cmpxchg.org: clean up css ref handling] Fixes: 5ac8fb31ad2e ("mm: memcontrol: convert reclaim iterator to simple css refcounting") Signed-off-by: Vladimir Davydov <vdavydov@virtuozzo.com> Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@kernel.org> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: <stable@vger.kernel.org> [3.19+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joseph Qi [Tue, 29 Dec 2015 22:54:06 +0000 (14:54 -0800)]
ocfs2: fix BUG when calculate new backup super
When resizing, it firstly extends the last gd. Once it should backup
super in the gd, it calculates new backup super and update the
corresponding value.
But it currently doesn't consider the situation that the backup super is
already done. And in this case, it still sets the bit in gd bitmap and
then decrease from bg_free_bits_count, which leads to a corrupted gd and
trigger the BUG in ocfs2_block_group_set_bits:
Guenter Roeck [Thu, 24 Dec 2015 05:04:31 +0000 (21:04 -0800)]
MIPS: VDSO: Fix build error with binutils 2.24 and earlier
Commit 2a037f310bab ("MIPS: VDSO: Fix build error") tries to fix a build
error seen with binutils 2.24 and earlier. However, the fix does not work,
and again results in the already known build errors if the kernel is built
with an earlier version of binutils.
Joe Stringer [Wed, 23 Dec 2015 22:39:27 +0000 (14:39 -0800)]
openvswitch: Fix template leak in error cases.
Commit 5b48bb8506c5 ("openvswitch: Fix helper reference leak") fixed a
reference leak on helper objects, but inadvertently introduced a leak on
the ct template.
Previously, ct_info.ct->general.use was initialized to 0 by
nf_ct_tmpl_alloc() and only incremented when ovs_ct_copy_action()
returned successful. If an error occurred while adding the helper or
adding the action to the actions buffer, the __ovs_ct_free_action()
cleanup would use nf_ct_put() to free the entry; However, this relies on
atomic_dec_and_test(ct_info.ct->general.use). This reference must be
incremented first, or nf_ct_put() will never free it.
Fix the issue by acquiring a reference to the template immediately after
allocation.
Fixes: cae3a2627520 ("openvswitch: Allow attaching helpers to ct action") Fixes: 5b48bb8506c5 ("openvswitch: Fix helper reference leak") Signed-off-by: Joe Stringer <joe@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Matias Bjørling [Tue, 29 Dec 2015 13:37:56 +0000 (14:37 +0100)]
lightnvm: wrong offset in bad blk lun calculation
dev->nr_luns reports the total number of luns available in a device
while dev->luns_per_chnl is the number of luns per channel.
When multiple channels are available, the offset is calculated from a
channel and lun id into a linear array. As it multiplies with
the total number of luns, we go out of bound when channel id > 0 and
causes the kernel to panic when we read a protected kernel memory area.
Linus Torvalds [Tue, 29 Dec 2015 00:45:14 +0000 (16:45 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Three late 4.4-rc fixes.
The first two were very small in terms of number of lines, the third
is more lines of change than I like this late in the cycle, but there
are positive test results from Avagotech and from my own test setup
with the target hardware, and given the problem was a 100% failure
case, I sent it through.
- A previous patch updated the mlx4 driver to use vmalloc when there
was not enough memory to get a contiguous region large enough for
our needs, so we need kvfree() whenever we free that item. We
missed one place, so fix that now.
- A previous patch added code to match incoming packets against a
specific device, but failed to compensate for devices that have
both InfiniBand and Ethernet ports. Fix that.
- Under certain vlan conditions, the ocrdma driver would fail to
bring up any vlan interfaces and would print out a circular locking
failure. Fix that"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
RDMA/be2net: Remove open and close entry points
RDMA/ocrdma: Depend on async link events from CNA
RDMA/ocrdma: Dispatch only port event when port state changes
RDMA/ocrdma: Fix vlan-id assignment in qp parameters
IB/mlx4: Replace kfree with kvfree in mlx4_ib_destroy_srq
IB/cma: cma_match_net_dev needs to take into account port_num
Jens Axboe [Mon, 28 Dec 2015 20:02:47 +0000 (13:02 -0700)]
null_blk: use async queue restart helper
If null_blk is run in NULL_IRQ_TIMER mode and with queue_mode NULL_Q_RQ,
we need to restart the queue from the hrtimer interrupt. We can't
directly invoke the request_fn from that context, so punt the queue run
to async kblockd context.
Tested-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Jens Axboe <axboe@fb.com>
Jens Axboe [Mon, 28 Dec 2015 20:01:22 +0000 (13:01 -0700)]
block: add blk_start_queue_async()
We currently only have an inline/sync helper to restart a stopped
queue. If drivers need an async version, they have to roll their
own. Add a generic helper instead.
Linus Torvalds [Mon, 28 Dec 2015 18:44:41 +0000 (10:44 -0800)]
Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes a bug in the algif_skcipher interface that can trigger a
kernel WARN_ON from user-space. It does so by using the new skcipher
interface which unlike the previous ablkcipher does not need to create
extra geniv objects which is what was used to trigger the WARN_ON"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: algif_skcipher - Use new skcipher interface
Devesh Sharma [Thu, 24 Dec 2015 18:14:08 +0000 (13:14 -0500)]
RDMA/be2net: Remove open and close entry points
Recently Dough Ledford reported a deadlock happening
between ocrdma-load sequence and NetworkManager service
issueing "open" on be2net interface.
The deadlock happens when any be2net hook (e.g. open/close) is called
in parallel to insmod ocrdma.ko.
A. be2net is sending administrative open/close event to ocrdma holding
device_list_mutex. It does this from ndo_open/ndo_stop hooks of be2net.
So sequence of locks is rtnl_lock---> device_list lock
B. When new ocrdma roce device gets registered, infiniband stack now
takes rtnl_lock in ib_register_device() in GID initialization routines.
So sequence of locks in this path is device_list lock ---> rtnl_lock.
This improper locking sequence causes deadlock.
In order to resolve the above deadlock condition, ocrdma intorduced a
patch to stop listening to administrative open/close events generated from
be2net driver. It now depends on link-state-change async-event generated from
CNA. This change leaves behind dead code which used to generate administrative
open/close events. This patch cleans-up all that dead code from be2net.
Devesh Sharma [Thu, 24 Dec 2015 18:14:07 +0000 (13:14 -0500)]
RDMA/ocrdma: Depend on async link events from CNA
Recently Dough Ledford reported a deadlock happening
between ocrdma-load sequence and NetworkManager service
issuing "open" on be2net interface.
The deadlock happens when any be2net hook (e.g. open/close) is called
in parallel to insmod ocrdma.ko.
A. be2net is sending administrative open/close event to ocrdma holding
device_list_mutex. It does this from ndo_open/ndo_stop hooks of be2net.
So sequence of locks is rtnl_lock---> device_list lock
B. When new ocrdma roce device gets registered, infiniband stack now
takes rtnl_lock in ib_register_device() in GID initialization routines.
So sequence of locks in this path is device_list lock ---> rtnl_lock.
This improper locking sequence causes deadlock.
With this patch we stop using administrative open and close events
injected by be2net driver. These events were used to dispatch PORT_ACTIVE
and PORT_ERROR events to the IB-stack. This patch implements a logic
to receive async-link-events generated from CNA whenever link-state-change
is detected. Now on, these async-events will be used to dispatch
PORT_ACTIVE and PORT_ERROR events to IB-stack.
Depending on async-events from CNA removes the need to hold device-list-mutex
and thus breaks the busy-wait scenario.
Devesh Sharma [Thu, 24 Dec 2015 18:14:06 +0000 (13:14 -0500)]
RDMA/ocrdma: Dispatch only port event when port state changes
Dispatch only port event to IB stack when port state changes.
Don't explicitly modify qps to error. Let application listen to
port events on async event queue or let QP fail with retry-exceeded
completion error.
Devesh Sharma [Thu, 24 Dec 2015 18:14:05 +0000 (13:14 -0500)]
RDMA/ocrdma: Fix vlan-id assignment in qp parameters
vlan-id is wrongly getting as 0 when PFC is enabled.
Set vlan-id configured by user in QP parameters.
In case vlan interface is not used, flash a warning to
user to configure vlan and assign vlan-id as 0 in qp params.
Fixes: dbf727de7440 ('IB/core: Use GID table in AH creation and dmac resolution') Cc: Matan Barak <matanb@mellanox.com> Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Accepted or peeled off sockets were missing a security label (e.g.
SELinux) which means that socket was in "unlabeled" state.
This patch clones the sock's label from the parent sock and resolves the
issue (similar to AF_BLUETOOTH protocol family).
Cc: Paul Moore <pmoore@redhat.com> Cc: David Teigland <teigland@redhat.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Paul Moore <paul@paul-moore.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Commit cacc06215271 ("sctp: use GFP_USER for user-controlled kmalloc")
missed two other spots.
For connectx, as it's more likely to be used by kernel users of the API,
it detects if GFP_USER should be used or not.
Fixes: cacc06215271 ("sctp: use GFP_USER for user-controlled kmalloc") Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 28 Dec 2015 02:12:21 +0000 (18:12 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
- Fix bitrot in __get_user_unaligned()
- EVA userspace accessor bug fixes.
- Fix for build issues with certain toolchains.
- Fix build error for VDSO with particular toolchain versions.
- Fix build error due to a variable that should have been removed by an
earlier patch
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix bitrot in __get_user_unaligned()
MIPS: Fix build error due to unused variables.
MIPS: VDSO: Fix build error
MIPS: CPS: drop .set mips64r2 directives
MIPS: uaccess: Take EVA into account in [__]clear_user
MIPS: uaccess: Take EVA into account in __copy_from_user()
MIPS: uaccess: Fix strlen_user with EVA
Linus Torvalds [Mon, 28 Dec 2015 02:06:31 +0000 (18:06 -0800)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A smallish set of fixes that we've been sitting on for a while now,
flushing the queue here so they go in. Summary:
A handful of fixes for OMAP, i.MX, Allwinner and Tegra:
- A clock rate and a PHY setup fix for i.MX6Q/DL
- A couple of fixes for the reduced serial bus (sunxi-rsb) on
Allwinner
- UART wakeirq fix for an OMAP4 board, timer config fixes for AM43XX.
- Suspend fix for Tegra124 Chromebooks
- Fix for missing implicit include that's different between
ARM/ARM64"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: tegra: Fix suspend hang on Tegra124 Chromebooks
bus: sunxi-rsb: Fix peripheral IC mapping runtime address
bus: sunxi-rsb: Fix primary PMIC mapping hardware address
ARM: dts: Fix UART wakeirq for omap4 duovero parlor
ARM: OMAP2+: AM43xx: select ARM TWD timer
ARM: OMAP2+: am43xx: enable GENERIC_CLOCKEVENTS_BROADCAST
fsl-ifc: add missing include on ARM64
ARM: dts: imx6: Fix Ethernet PHY mode on Ventana boards
ARM: dts: imx: Fix the assigned-clock mismatch issue on imx6q/dl
bus: sunxi-rsb: unlock on error in sunxi_rsb_read()
ARM: dts: sunxi: sun6i-a31s-primo81.dts: add touchscreen axis swapping property
Linus Torvalds [Sun, 27 Dec 2015 04:08:47 +0000 (20:08 -0800)]
Merge tag 'pm+acpi-4.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix an ACPI processor driver regression introduced during the
4.3 cycle and a mistake in the recently added SCPI support in the
arm_big_little cpufreq driver.
Specifics:
- Fix a thermal management issue introduced by an ACPI processor
driver change made during the 4.3 development cycle that failed to
return 0 from a function on success which triggered an error
cleanup path every time it had been called that deleted useful data
structures created previously (Srinivas Pandruvada).
- Fix a variable data type issue in the arm_big_little cpufreq
driver's SCPI support code added recently that prevents error
handling in there from working correctly (Dan Carpenter)"
* tag 'pm+acpi-4.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: scpi-cpufreq: signedness bug in scpi_get_dvfs_info()
ACPI / processor: Fix thermal cooling device regression
Linus Torvalds [Sun, 27 Dec 2015 03:55:16 +0000 (19:55 -0800)]
Merge tag 'upstream-4.4-rc7' of git://git.infradead.org/linux-ubifs
Pull UBI bug fixes from Richard Weinberger:
"This contains four bug fixes for UBI"
* tag 'upstream-4.4-rc7' of git://git.infradead.org/linux-ubifs:
mtd: ubi: don't leak e if schedule_erase() fails
mtd: ubi: fixup error correction in do_sync_erase()
UBI: fix use of "VID" vs. "EC" in header self-check
UBI: fix return error code
Linus Torvalds [Sun, 27 Dec 2015 03:48:09 +0000 (19:48 -0800)]
Merge tag 'trace-v4.4-rc4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace/recordmcount fix from Steven Rostedt:
"Russell King was reporting lots of warnings when he compiled his
kernel with ftrace enabled. With some investigation it was discovered
that it was his compile setup. He was using ccache with hard links,
which allowed recordmcount to process the same .o twice. When this
happens, recordmcount will detect that it was already done and give a
warning about it.
Russell fixed this by having recordmcount detect that the object file
has more than one hard link, and if it does, it unlinks the object
file after it maps it and processes then. This appears to fix the
issue.
As you did not like the fact that recordmcount modified the file in
place and thought that it should do the modifications in memory and
then write it out to disk and move it over the old file to prevent
other more subtle issues like the one above, a second patch is added
on top of Russell's to do just that. Luckily the original code had
write and lseek wrappers that I was able to modify to not do inplace
writes, but simply keep track of the changes made in memory. When a
write is made, a "update" flag is set, and at the end of processing,
if the update is set, then it writes the file with changes out to a
new file, and then renames it over the original one.
The file descriptor is still passed to the write and lseek wrappers
because removing that would cause the change to be more intrusive.
That can be removed in a follow up cleanup patch that can wait till
the next merge window"
* tag 'trace-v4.4-rc4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace/scripts: Have recordmcount copy the object file
scripts: recordmcount: break hardlinks
Linus Torvalds [Sat, 26 Dec 2015 22:58:06 +0000 (14:58 -0800)]
Merge tag 'arc-4.4-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Sorry for this late pull request, but these are all important fixes
for code introduced/updated in this release which we will otherwise
end up back porting.
- Unwinder rework (A revert followed by better fix)
- Build errors: MMUv2, modules with -Os
- highmem section mismatch build splat"
* tag 'arc-4.4-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: dw2 unwind: Catch Dwarf SNAFUs early
ARC: dw2 unwind: Don't bail for CIE.version != 1
Revert "ARC: dw2 unwind: Ignore CIE version !=1 gracefully instead of bailing"
ARC: Fix linking errors with CONFIG_MODULE + CONFIG_CC_OPTIMIZE_FOR_SIZE
ARC: mm: fix building for MMU v2
ARC: mm: HIGHMEM: Fix section mismatch splat
Linus Torvalds [Fri, 25 Dec 2015 21:19:50 +0000 (13:19 -0800)]
Merge branch 'parisc-4.4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc system call restart fix from Helge Deller:
"The architectural design of parisc always uses two instructions to
call kernel syscalls (delayed branch feature). This means that the
instruction following the branch (located in the delay slot of the
branch instruction) is executed before control passes to the branch
destination.
Depending on which assembler instruction and how it is used in
usersapce in the delay slot, this sometimes made restarted syscalls
like futex() and poll() failing with -ENOSYS"
* 'parisc-4.4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix syscall restarts
1) Finally make perf stack backtraces stable on sparc, several problems
(mostly due to the context in which the user copies from the stack
are done) contributed to this.
From Rob Gardner.
2) Export ADI capability if the cpu supports it.
3) Hook up userfaultfd system call.
4) When faults happen during user copies we really have to clean up and
restore the FPU state fully. Also from Rob Gardner
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
tty/serial: Skip 'NULL' char after console break when sysrq enabled
sparc64: fix FP corruption in user copy functions
sparc64: Perf should save/restore fault info
sparc64: Ensure perf can access user stacks
sparc64: Don't set %pil in rtrap_nmi too early
sparc64: Add ADI capability to cpu capabilities
tty: serial: constify sunhv_ops structs
sparc: Hook up userfaultfd system call
Vijay Kumar [Wed, 23 Dec 2015 18:55:33 +0000 (10:55 -0800)]
tty/serial: Skip 'NULL' char after console break when sysrq enabled
When sysrq is triggered from console, serial driver for SUN hypervisor
console receives a console break and enables the sysrq. It expects a valid
sysrq char following with break. Meanwhile if driver receives 'NULL'
ASCII char then it disables sysrq and sysrq handler will never be invoked.
This fix skips calling uart sysrq handler when 'NULL' is received while
sysrq is enabled.
Signed-off-by: Vijay Kumar <vijay.ac.kumar@oracle.com> Acked-by: Karl Volz <karl.volz@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rob Gardner [Wed, 23 Dec 2015 06:24:49 +0000 (23:24 -0700)]
sparc64: fix FP corruption in user copy functions
Short story: Exception handlers used by some copy_to_user() and
copy_from_user() functions do not diligently clean up floating point
register usage, and this can result in a user process seeing invalid
values in floating point registers. This sometimes makes the process
fail.
Long story: Several cpu-specific (NG4, NG2, U1, U3) memcpy functions
use floating point registers and VIS alignaddr/faligndata to
accelerate data copying when source and dest addresses don't align
well. Linux uses a lazy scheme for saving floating point registers; It
is not done upon entering the kernel since it's a very expensive
operation. Rather, it is done only when needed. If the kernel ends up
not using FP regs during the course of some trap or system call, then
it can return to user space without saving or restoring them.
The various memcpy functions begin their FP code with VISEntry (or a
variation thereof), which saves the FP regs. They conclude their FP
code with VISExit (or a variation) which essentially marks the FP regs
"clean", ie, they contain no unsaved values. fprs.FPRS_FEF is turned
off so that a lazy restore will be triggered when/if the user process
accesses floating point regs again.
The bug is that the user copy variants of memcpy, copy_from_user() and
copy_to_user(), employ an exception handling mechanism to detect faults
when accessing user space addresses, and when this handler is invoked,
an immediate return from the function is forced, and VISExit is not
executed, thus leaving the fprs register in an indeterminate state,
but often with fprs.FPRS_FEF set and one or more dirty bits. This
results in a return to user space with invalid values in the FP regs,
and since fprs.FPRS_FEF is on, no lazy restore occurs.
This bug affects copy_to_user() and copy_from_user() for NG4, NG2,
U3, and U1. All are fixed by using a new exception handler for those
loads and stores that are done during the time between VISEnter and
VISExit.
n.b. In NG4memcpy, the problematic code can be triggered by a copy
size greater than 128 bytes and an unaligned source address. This bug
is known to be the cause of random user process memory corruptions
while perf is running with the callgraph option (ie, perf record -g).
This occurs because perf uses copy_from_user() to read user stacks,
and may fault when it follows a stack frame pointer off to an
invalid page. Validation checks on the stack address just obscure
the underlying problem.
Signed-off-by: Rob Gardner <rob.gardner@oracle.com> Signed-off-by: Dave Aldridge <david.j.aldridge@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rob Gardner [Wed, 23 Dec 2015 04:16:07 +0000 (21:16 -0700)]
sparc64: Perf should save/restore fault info
There have been several reports of random processes being killed with
a bus error or segfault during userspace stack walking in perf. One
of the root causes of this problem is an asynchronous modification to
thread_info fault_address and fault_code, which stems from a perf
counter interrupt arriving during kernel processing of a "benign"
fault, such as a TSB miss. Since perf_callchain_user() invokes
copy_from_user() to read user stacks, a fault is not only possible,
but probable. Validity checks on the stack address merely cover up the
problem and reduce its frequency.
The solution here is to save and restore fault_address and fault_code
in perf_callchain_user() so that the benign fault handler is not
disturbed by a perf interrupt.
Signed-off-by: Rob Gardner <rob.gardner@oracle.com> Signed-off-by: Dave Aldridge <david.j.aldridge@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rob Gardner [Wed, 23 Dec 2015 04:16:06 +0000 (21:16 -0700)]
sparc64: Ensure perf can access user stacks
When an interrupt (such as a perf counter interrupt) is delivered
while executing in user space, the trap entry code puts ASI_AIUS in
%asi so that copy_from_user() and copy_to_user() will access the
correct memory. But if a perf counter interrupt is delivered while the
cpu is already executing in kernel space, then the trap entry code
will put ASI_P in %asi, and this will prevent copy_from_user() from
reading any useful stack data in either of the perf_callchain_user_X
functions, and thus no user callgraph data will be collected for this
sample period. An additional problem is that a fault is guaranteed
to occur, and though it will be silently covered up, it wastes time
and could perturb state.
In perf_callchain_user(), we ensure that %asi contains ASI_AIUS
because we know for a fact that the subsequent calls to
copy_from_user() are intended to read the user's stack.
[ Use get_fs()/set_fs() -DaveM ]
Signed-off-by: Rob Gardner <rob.gardner@oracle.com> Signed-off-by: Dave Aldridge <david.j.aldridge@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rob Gardner [Tue, 22 Dec 2015 04:48:03 +0000 (21:48 -0700)]
sparc64: Don't set %pil in rtrap_nmi too early
Commit 28a1f53 delays setting %pil to avoid potential
hardirq stack overflow in the common rtrap_irq path.
Setting %pil also needs to be delayed in the rtrap_nmi
path for the same reason.
Signed-off-by: Rob Gardner <rob.gardner@oracle.com> Signed-off-by: Dave Aldridge <david.j.aldridge@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Khalid Aziz [Thu, 17 Dec 2015 17:33:50 +0000 (10:33 -0700)]
sparc64: Add ADI capability to cpu capabilities
Add ADI (Application Data Integrity) capability to cpu capabilities list.
ADI capability allows virtual addresses to be encoded with a tag in
bits 63-60. This tag serves as an access control key for the regions
of virtual address with ADI enabled and a key set on them. Hypervisor
encodes this capability as "adp" in "hwcap-list" property in machine
description.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Aya Mahfouz [Mon, 14 Dec 2015 23:37:57 +0000 (01:37 +0200)]
tty: serial: constify sunhv_ops structs
Constifies sunhv_ops structures in tty's serial
driver since they are not modified after their
initialization.
Detected and found using Coccinelle.
Suggested-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Aya Mahfouz <mahfouz.saif.elyazal@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 24 Dec 2015 09:21:22 +0000 (12:21 +0300)]
qlcnic: fix a loop exit condition better
In the original code, if we succeeded on the last iteration through the
loop then we still returned failure.
Fixes: 389e4e04ad2d ('qlcnic: fix a timeout loop') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Wed, 23 Dec 2015 12:42:43 +0000 (13:42 +0100)]
net: cdc_ncm: avoid changing RX/TX buffers on MTU changes
NCM buffer sizes are negotiated with the device independently of
the network device MTU. The RX buffers are allocated by the
usbnet framework based on the rx_urb_size value set by cdc_ncm. A
single RX buffer can hold a number of MTU sized packets.
The default usbnet change_mtu ndo only modifies rx_urb_size if it
is equal to hard_mtu. And the cdc_ncm driver will set rx_urb_size
and hard_mtu independently of each other, based on dwNtbInMaxSize
and dwNtbOutMaxSize respectively. It was therefore assumed that
usbnet_change_mtu() would never touch rx_urb_size. This failed to
consider the case where dwNtbInMaxSize and dwNtbOutMaxSize happens
to be equal.
Fix by implementing an NCM specific change_mtu ndo, modifying the
netdev MTU without touching the buffer size settings.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 23 Dec 2015 15:54:27 +0000 (16:54 +0100)]
geneve: initialize needed_headroom
Currently the needed_headroom field for the geneve device is left
to the default value.
This patch set it to space required for basic geneve encapsulation,
so that we can avoid the skb head re-allocation on xmit.
This give a 6% speedup for unsegment traffic on geneve tunnel.
v1 -> v2:
- add ETH_HLEN for the lower device to the needed headroom
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: honor ifindex in case we receive ll addresses in router advertisements
Marc Haber reported we don't honor interface indexes when we receive link
local router addresses in router advertisements. Luckily the non-strict
version of ipv6_chk_addr already does the correct job here, so we can
simply use it to lighten the checks and use those addresses by default
without any configuration change.
Link: <http://permalink.gmane.org/gmane.linux.network/391348> Reported-by: Marc Haber <mh+netdev@zugschlus.de> Cc: Marc Haber <mh+netdev@zugschlus.de> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 23 Dec 2015 18:28:39 +0000 (10:28 -0800)]
Merge tag 'sound-4.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This shouldn't be a nightmare before Christmas: just a handful small
device-specific fixes for various ASoC and HD-audio drivers. Most of
them are stable fixes"
* tag 'sound-4.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fix silent headphone output on MacPro 4,1 (v2)
ASoC: fsl_sai: fix no frame clk in master mode
ALSA: hda - Set SKL+ hda controller power at freeze() and thaw()
ASoC: sgtl5000: fix VAG power up timing
ASoC: rockchip: spdif: Set transmit data level to 16 samples
ASoC: wm8974: set cache type for regmap
ASoC: es8328: Fix shifts for mixer switches
ASoC: davinci-mcasp: Fix XDATA check in mcasp_start_tx
ASoC: es8328: Fix deemphasis values
Linus Torvalds [Wed, 23 Dec 2015 18:22:16 +0000 (10:22 -0800)]
Merge tag 'drm-intel-fixes-2015-12-23' of git://anongit.freedesktop.org/drm-intel
Pull i915 drm fixes from Jani Nikula:
"Here's a batch of i915 fixes all around. It may be slightly bigger
than one would hope for at this stage, but they've all been through
testing in our -next before being picked up for v4.4. Also, I missed
Dave's fixes pull earlier today just because I wanted an extra testing
round on this. So I'm fairly confident.
Wishing you all the things it is customary to wish this time of the
year"
* tag 'drm-intel-fixes-2015-12-23' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Correct max delay for HDMI hotplug live status checking
drm/i915: mdelay(10) considered harmful
drm/i915: Kill intel_crtc->cursor_bo
drm/i915: Workaround CHV pipe C cursor fail
drm/i915: Only spin whilst waiting on the current request
drm/i915: Limit the busy wait on requests to 5us not 10ms!
drm/i915: Break busywaiting for requests on pending signals
drm/i915: Disable primary plane if we fail to reconstruct BIOS fb (v2)
drm/i915: Set the map-and-fenceable flag for preallocated objects
drm/i915: Drop the broken cursor base==0 special casing
Linus Torvalds [Wed, 23 Dec 2015 18:11:12 +0000 (10:11 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Not much happening, should have dequeued this lot earlier.
One amdgpu, one nouveau and one exynos fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/exynos: atomic check only enabled crtc states
drm/nouveau/bios/fan: hardcode the fan mode to linear
drm/amdgpu: fix user fence handling
Ville Syrjälä [Thu, 10 Dec 2015 16:22:31 +0000 (18:22 +0200)]
drm/i915: Unbreak check_digital_port_conflicts()
Atomic changes broke check_digital_port_conflicts(). It needs to look
at the global situation instead of just trying to find a conflict
within the current atomic state.
This bug made my HSW explode spectacularly after I had split the DDI
encoders into separate DP and HDMI encoders. With the fix, things
seem much more solid.
I hope holding the connection_mutex is enough protection that we can
actually walk the connectors even if they're not part of the current
atomic state...
v2: Regenerate the patch so that it actually applies (Jani)
Takashi Iwai [Wed, 23 Dec 2015 07:30:28 +0000 (08:30 +0100)]
Merge tag 'asoc-fix-v4.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.4
A collection of small driver specific fixes here, nothing that'll affect
users who don't have the devices concerned. At least the wm8974 bug
indicates that there's not too many users of some of these devices.
Wengang Wang [Thu, 17 Dec 2015 02:54:15 +0000 (10:54 +0800)]
IB/mlx4: Replace kfree with kvfree in mlx4_ib_destroy_srq
Commit 0ef2f05c7e02ff99c0b5b583d7dee2cd12b053f2 uses vmalloc for WR buffers
when needed and uses kvfree to free the buffers. It missed changing kfree
to kvfree in mlx4_ib_destroy_srq().
Reported-by: Matthew Finaly <matt@Mellanox.com> Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Matan Barak [Mon, 21 Dec 2015 15:01:24 +0000 (17:01 +0200)]
IB/cma: cma_match_net_dev needs to take into account port_num
Previously, cma_match_net_dev called cma_protocol_roce which
tried to verify that the IB device uses RoCE protocol. However,
if rdma_id wasn't bound to a port, then the check would occur
against the first port of the device without regard to whether
that port was even of the same type as the type of port the
incoming packet was received on.
Fix this by passing the port of the request and only checking
against the same port of the device.
Reported-by: Or Gerlitz <gerlitz.or@gmail.com> Fixes: b8cab5dab15f ('IB/cma: Accept connection without a valid netdev on RoCE') Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
projects / mirror_ubuntu-focal-kernel.git / log