* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
ide/Kconfig: add missing range check for IDE_MAX_HWIFS
hpt366: fix kernel oops with HPT302N
ide/pci/delkin_cb.c: add new PCI ID
Fix a regression due to the patch "NFS: disconnect before retrying NFSv4
requests over TCP"
The assumption made in xprt_transmit() that the condition
"req->rq_bytes_sent == 0 and request is on the receive list"
should imply that we're dealing with a retransmission is false.
Firstly, it may simply happen that the socket send queue was full
at the time the request was initially sent through xprt_transmit().
Secondly, doing this for each request that was retransmitted implies
that we disconnect and reconnect for _every_ request that happened to
be retransmitted irrespective of whether or not a disconnection has
already occurred.
Fix is to move this logic into the call_status request timeout handler.
NFS: Fix the 'desynchronized value of nfs_i.ncommit' error
Redirtying a request that is already marked for commit will screw up the
accounting for NR_UNSTABLE_NFS as well as nfs_i.ncommit.
Ensure that all requests on the commit queue are labelled with the
PG_NEED_COMMIT flag, and avoid moving them onto the dirty list inside
nfs_page_mark_flush().
Also inline nfs_mark_request_dirty() into nfs_page_mark_flush() for
atomicity reasons. Avoid dropping the spinlock until we're done marking the
request in the radix tree and have added it to the ->dirty list.
Dave Jones [Fri, 20 Apr 2007 19:58:00 +0000 (15:58 -0400)]
Longhaul - Revert ACPI C3 on Longhaul ver. 2
Support for Longhaul ver. 2 broke driver for VIA C3 Eden 600MHz with
Samuel 2 core. Processor is not able to switch frequency anymore. I
don't know much about this issue at the moment, but until (if ever) I
will know why, this part should be reversed.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl> Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have a 10-15% performance regression for sequential writes on TCQ/NCQ
enabled drives in 2.6.21-rcX after the CFQ update went in. It has been
reported by Valerie Clement <valerie.clement@bull.net> and the Intel
testing folks. The regression is because of CFQ's now more aggressive
queue control, limiting the depth available to the device.
This patches fixes that regression by allowing a greater depth when only
one queue is busy. It has been tested to not impact sync-vs-async
workloads too much - we still do a lot better than 2.6.20.
Dave Johnson [Wed, 18 Apr 2007 14:39:41 +0000 (10:39 -0400)]
[MIPS] Fix wrong checksum for split TCP packets on 64-bit MIPS
I've traced down an off-by-one TCP checksum calculation error under
the following conditions:
1) The TCP code needs to split a full-sized packet due to a reduced
MSS (typically due to the addition of TCP options mid-stream like
SACK).
_AND_
2) The checksum of the 2nd fragment is larger than the checksum of the
original packet. After subtraction this results in a checksum for
the 1st fragment with bits 16..31 set to 1. (this is ok)
_AND_
3) The checksum of the 1st fragment's TCP header plus the previously
32bit checksum of the 1st fragment DOES NOT cause a 32bit overflow
when added together. This results in a checksum of the TCP header
plus TCP data that still has the upper 16 bits as 1's.
_THEN_
4) The TCP+data checksum is added to the checksum of the pseudo IP
header with csum_tcpudp_nofold() incorrectly (the bug).
The problem is the checksum of the TCP+data is passed to
csum_tcpudp_nofold() as an 32bit unsigned value, however the assembly
code acts on it as if it is a 64bit unsigned value.
This causes an incorrect 32->64bit extension if the sum has bit 31
set. The resulting checksum is off by one.
This problems is data and TCP header dependent due to #2 and #3
above so it doesn't occur on every TCP packet split.
Signed-off-by: Dave Johnson <djohnson+linux-mips@sw.starentnetworks.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With commit 63dc68a8cf60cb110b147dab1704d990808b39e2, kernel can not
handle BUG() and BUG_ON() properly since get_user() returns false for
kernel code. Use __get_user() to skip unnecessary access_ok(). This
patch also make BRK_BUG code encoded in the TNE instruction.
[MIPS] Retry {save,restore}_fp_context if failed in atomic context.
The save_fp_context()/restore_fp_context() might sleep on accessing
user stack and therefore might lose FPU ownership in middle of them.
If these function failed due to "in_atomic" test in do_page_fault,
touch the sigcontext area in non-atomic context and retry these
save/restore operation.
This is a replacement of a (broken) fix which was titled "Allow CpU
exception in kernel partially".
The commit 4d40bff7110e9e1a97ff8c01bdd6350e9867cc10 ("Allow CpU
exception in kernel partially") was broken. The commit was to fix
theoretical problem but broke usual case. Revert it for now.
Mark Mason [Fri, 13 Apr 2007 17:32:25 +0000 (10:32 -0700)]
[MIPS] Add missing silicon revisions for BCM112x
Recent versions of the BCM112X processors aren't recognized by Linux
(preventing Linux from booting on those processors). This patch adds
support for those that are missing.
Signed-off-by: Mark Mason <mason@broadcom.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
but it's likely that the commit itself is not really introducing the
bug, but just allowing an unrelated problem to rear its ugly head (ie
one current working theory is that the code exposes us to a hardware
race condition by decreasing the amount of time we spend in each NAPI
poll cycle).
We'll revert it until root cause is known. Intel has a repeatable
reproduction on two different machines and bus traces of the hardware
doing something bad.
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: Jeff Garzik <jeff@garzik.org> Cc: David S. Miller <davem@davemloft.net> Cc: Greg KH <gregkh@suse.de> Cc: Dave Jones <davej@redhat.com> Cc: Auke Kok <auke-jan.h.kok@intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 19 Apr 2007 10:09:52 +0000 (11:09 +0100)]
pata_sis: Fix oops on boot
A small number of SiS setups require special handling (not many judging
by how long this dumb bug survived). A couple of Fedora 7 devel testers
hit an Oops on pata_sis loading which is caused by terminal confusion
between chipset as 'the chipset we have found' and chipset as 'array
iterator'
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Paul Mackerras [Thu, 19 Apr 2007 20:05:52 +0000 (13:05 -0700)]
[PPP]: Fix skbuff.c:BUG due incorrect logic in process_input_packet()
From: Paul Mackerras <paulus@samba.org>
This fixes:
Subject: kernel BUG at net/core/skbuff.c in linux-2.6.21-rc6
process_input_packet() treats the case where the first byte is 0xff
(PPP_ALLSTATIONS) but the second byte is 0x03 (PPP_UI) as indicating a
packet with a PPP protocol number of 0xff. Arguably that's wrong
since PPP protocol 0xff is reserved, and the RFC does envision the
possibility of receiving frames where the control field has values
other than 0x03.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Yukon EC Ultra chips have transmit settings for store and
forward and PCI buffering. By setting these appropriately, normal
performance goes from 750Mbytes/sec to 940Mbytes/sec (non-jumbo).
It is also possible to do Jumbo mode, but it means turning off
TSO and checksum offload so the performance gets worse. There isn't
enough buffering for checksum offload to work.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
This device is having all sorts of problems that lead to data corruption
and system instability. It gets receive status and data out of order,
it generates descriptor and TSO errors, etc.
Until the problems are resolved, it should not be used by anyone
who cares about there system.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
The basic structure of "normal" UDP/IP/Ethernet
frames (that actually work):
- It starts with the Ethernet header (dest MAC, src MAC, etc.)
- The next part is occupied by the IP header (version info, length of
packet, id=0, fragment offset=0, checksum, from / to address, etc.)
- Then comes the UDP header (src / dest port, length, checksum)
- Actual payload
- Ethernet checksum
Now what's different for IP fragment:
- The IP header has id set to some value (same for all fragments),
offset is set appropriately (i.e. 0 for first fragment, following
according to size of other fragments), size is the length of the frame.
- UDP header is unchanged. I.e. length is according to full UDP
datagram, not just the part within the actual frame! But this is only
true within the first frame: all following frames don't have a valid
UDP-header at all.
The spidernet silicon seems to be quite intelligent: It's able to
compute (IP / UDP / Ethernet) checksums on the fly and tests if frames
are conforming to RFC -- at least conforming to RFC on complete frames.
But IP fragments are different as explained above:
I.e. for IP fragments containing part of a UDP datagram it sees
incompatible length in the headers for IP and UDP in the first frame
and, thus, skips this frame. But the content *is* correct for IP
fragments. For all following frames it finds (most probably) no valid
UDP header at all. But this *is* also correct for IP fragments.
The Linux IP-stack seems to be clever in this point. It expects the
spidernet to calculate the checksum (since the module claims to be able
to do so) and marks the skb's for "normal" frames accordingly
(ip_summed set to CHECKSUM_HW).
But for the IP fragments it does not expect the driver to be capable to
handle the frames appropriately. Thus all checksums are allready
computed. This is also flaged within the skb (ip_summed set to
CHECKSUM_NONE).
Unfortunately the spidernet driver ignores that hints. It tries to send
the IP fragments of UDP datagrams as normal UDP/IP frames. Since they
have different structure the silicon detects them the be not
"well-formed" and skips them.
The following one-liner against 2.6.21-rc2 changes this behavior. If the
IP-stack claims to have done the checksumming, the driver should not
try to checksum (and analyze) the frame but send it as is.
Signed-off-by: Norbert Eicker <n.eicker@fz-juelich.de> Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Divy Le Ray [Tue, 17 Apr 2007 18:06:30 +0000 (11:06 -0700)]
cxgb3 - Fix low memory conditions
Reuse the incoming skb when a clientless abort req is recieved.
The release of RDMA connections HW resources might be deferred in
low memory situations.
Ensure that no further activity is passed up to the RDMA driver
for these connections.
Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Avi Kivity [Wed, 18 Apr 2007 08:18:18 +0000 (11:18 +0300)]
KVM: Fix off-by-one when writing to a nonpae guest pde
Nonpae guest pdes are shadowed by two pae ptes, so we double the offset
twice: once to account for the pte size difference, and once because we
need to shadow pdes for a single guest pde.
But when writing to the upper guest pde we also need to truncate the
lower bits, otherwise the multiply shifts these bits into the pde index
and causes an access to the wrong shadow pde. If we're at the end of the
page (accessing the very last guest pde) we can even overflow into the
next host page and oops.
[NETLINK]: Don't attach callback to a going-away netlink socket
There is a race between netlink_dump_start() and netlink_release()
that can lead to the situation when a netlink socket with non-zero
callback is freed.
spin_lock(&nlk->cb_lock);
if (nlk->cb) { /* false */
...
}
spin_unlock(&nlk->cb_lock);
spin_lock(&nlk->cb_lock);
if (nlk->cb) { /* false */
...
}
nlk->cb = cb;
spin_unlock(&nlk->cb_lock);
...
sock_orphan(sk);
/*
* proceed with releasing
* the socket
*/
The proposal it to make sock_orphan before detaching the callback
in netlink_release() and to check for the sock to be SOCK_DEAD in
netlink_dump_start() before setting a new callback.
Signed-off-by: Denis Lunev <den@openvz.org> Signed-off-by: Kirill Korotaev <dev@openvz.org> Signed-off-by: Pavel Emelianov <xemul@openvz.org> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Olaf Kirch [Wed, 18 Apr 2007 22:07:22 +0000 (15:07 -0700)]
[IrDA]: Correctly handling socket error
This patch fixes an oops first reported in mid 2006 - see
http://lkml.org/lkml/2006/8/29/358 The cause of this bug report is that
when an error is signalled on the socket, irda_recvmsg_stream returns
without removing a local wait_queue variable from the socket's sk_sleep
queue. This causes havoc further down the road.
In response to this problem, a patch was made that invoked sock_orphan on
the socket when receiving a disconnect indication. This is not a good fix,
as this sets sk_sleep to NULL, causing applications sleeping in recvmsg
(and other places) to oops.
This is against the latest net-2.6 and should be considered for -stable
inclusion.
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com> Signed-off-by: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[SCTP]: Do not interleave non-fragments when in partial delivery
The way partial delivery is currently implemnted, it is possible to
intereleave a message (either from another steram, or unordered) that
is not part of partial delivery process. The only way to this is for
a message to not be a fragment and be 'in order' or unorderd for a
given stream. This will result in bypassing the reassembly/ordering
queues where things live duing partial delivery, and the
message will be delivered to the socket in the middle of partial delivery.
This is a two-fold problem, in that:
1. the app now must check the stream-id and flags which it may not
be doing.
2. this clearing partial delivery state from the association and results
in ulp hanging.
This patch is a band-aid over a much bigger problem in that we
don't do stream interleave.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[BRIDGE]: Unaligned access when comparing ethernet addresses
[SCTP]: Unmap v4mapped addresses during SCTP_BINDX_REM_ADDR operation.
[SCTP]: Fix assertion (!atomic_read(&sk->sk_rmem_alloc)) failed message
[NET]: Set a separate lockdep class for neighbour table's proxy_queue
[NET]: Fix UDP checksum issue in net poll mode.
[KEY]: Fix conversion between IPSEC_MODE_xxx and XFRM_MODE_xxx.
[NET]: Get rid of alloc_skb_from_cache
Jean Delvare [Tue, 17 Apr 2007 07:32:27 +0000 (00:32 -0700)]
hwmon/w83627ehf: Fix the fan5 clock divider write
Users have been complaining about the w83627ehf driver flooding their logs
with debug messages like:
w83627ehf 9191-0a10: Increasing fan 4 clock divider from 64 to 128
or:
w83627ehf 9191-0290: Increasing fan 4 clock divider from 4 to 8
The reason is that we failed to actually write the LSB of the encoded clock
divider value for that fan, causing the next read to report the same old value
again and again.
Additionally, the fan number was improperly reported, making the bug harder to
find.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Russell King [Tue, 17 Apr 2007 07:32:26 +0000 (00:32 -0700)]
Provide dummy devm_ioport_* if !HAS_IOPORT
Provide an dummy implementation of devm_ioport_map() and
devm_ioport_unmap() to allow drivers (eg, pata_platform) to build for
platforms where CONFIG_NO_IOPORT is selected.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Tue, 17 Apr 2007 05:53:22 +0000 (22:53 -0700)]
spi: fix use of set_cs in spi_s3c24xx driver
It turns out that the last patch to change set_cs to be kept in the
controller's structure instead of the platform data was an incomplete
change, and did not change the references to platfrom data in the setup
xfer code. (This can prevent an oops.)
Reported-by: <Ling.Alex@iac.com.tw> Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Determine correct hose configuration; RAWHIDE family can have
2 or 4 hoses, so make sure non-existent hoses are ignored.
arch/alpha/kernel/err_titan.c
Supply a needed #include <asm/irq_regs.h>
arch/alpha/kernel/module.c
Add some useful output to the relocation overflow messages.
arch/alpha/kernel/sys_noritake.c
Supply necessary noritake_end_irq() to correct interrupt handling.
This fixes a problem first noted by hangs during boot probing with
a DE500-BA TULIP NIC present.
arch/alpha/kernel/sys_sio.c
Correct saving of original PIRQ register (PCI IRQ routing);
change default PIRQ setting to leave PCI IRQs 9 and 14 free to
be used for sound (Multia) and IDE (any), respectively.
include/asm-alpha/io.h
Supply the "isa_virt_to_bus" routine.
Signed-off-by: Jay Estabrook <jay.estabrook@hp.com> Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Richard Henderson <rth@twiddle.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While digging through my MAP_FIXED changes, I found that rather obvious
bug in /dev/mem mmap implementation for nommu archs. get_unmapped_area()
is expected to return an address, not a pfn.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-By: David Howells <dhowells@redhat.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Tue, 17 Apr 2007 05:53:15 +0000 (22:53 -0700)]
kernel-doc: fix plist.h comments
Make kernel-doc comments match macro names.
Correct parameter names in a few places.
Remove '#' from beginning of kernel-doc comment macro names.
Remove extra (erroneous) blank lines in kernel-doc.
Warning(plist.h:100): Cannot understand * #PLIST_HEAD_INIT - static struct plist_head initializer on line 100 - I thought it was a doc line
Warning(plist.h:112): Cannot understand * #PLIST_NODE_INIT - static struct plist_node initializer on line 112 - I thought it was a doc line
Warning(plist.h:103): No description found for parameter '_lock'
Warning(plist.h:129): No description found for parameter 'lock'
Warning(plist.h:158): No description found for parameter 'pos'
Warning(plist.h:169): No description found for parameter 'pos'
Warning(plist.h:169): No description found for parameter 'n'
Warning(plist.h:179): No description found for parameter 'mem'
This still leaves one warning & one error that need attention:
Error(plist.h:219): cannot understand prototype: '('
Warning(plist.h): no structured comments found
Acked-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: Daniel Walker <dwalker@mvista.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Oleg Nesterov <oleg@tv-sign.ru> Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 17 Apr 2007 05:53:13 +0000 (22:53 -0700)]
exec.c: fix coredump to pipe problem and obscure "security hole"
The patch checks for "|" in the pattern not the output and doesn't nail a
pid on to a piped name (as it is a program name not a file)
Also fixes a very very obscure security corner case. If you happen to have
decided on a core pattern that starts with the program name then the user
can run a program called "|myevilhack" as it stands. I doubt anyone does
this.
Signed-off-by: Alan Cox <alan@redhat.com> Confirmed-by: Christopher S. Aker <caker@theshore.net> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don Zickus [Tue, 17 Apr 2007 05:53:12 +0000 (22:53 -0700)]
allow vmsplice to work in 32-bit mode on ppc64
Trivial change to pass vmsplice arguments through the compat layer on
pp64.
Signed-off-by: Don Zickus <dzickus@redhat.com> Acked-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[BRIDGE]: Unaligned access when comparing ethernet addresses
compare_ether_addr() implicitly requires that the addresses
passed are 2-bytes aligned in memory.
This is not true for br_stp_change_bridge_id() and
br_stp_recalculate_bridge_id() in which one of the addresses
is unsigned char *, and thus may not be 2-bytes aligned.
Paolo Galtieri [Tue, 17 Apr 2007 19:52:36 +0000 (12:52 -0700)]
[SCTP]: Unmap v4mapped addresses during SCTP_BINDX_REM_ADDR operation.
During the sctp_bindx() call to add additional addresses to the
endpoint, any v4mapped addresses are converted and stored as regular
v4 addresses. However, when trying to remove these addresses, the
v4mapped addresses are not converted and the operation fails. This
patch unmaps the addresses on during the remove operation as well.
Signed-off-by: Paolo Galtieri <pgaltieri@mvista.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In current implementation, LKSCTP does receive buffer accounting for
data in sctp_receive_queue and pd_lobby. However, LKSCTP don't do
accounting for data in frag_list when data is fragmented. In addition,
LKSCTP doesn't do accounting for data in reasm and lobby queue in
structure sctp_ulpq.
When there are date in these queue, assertion failed message is printed
in inet_sock_destruct because sk_rmem_alloc of oldsk does not become 0
when socket is destroyed.
Signed-off-by: Tsutomu Fujii <t-fujii@nb.jp.nec.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In net poll mode, the current checksum function doesn't consider the
kind of packet which is padded to reach a specific minimum length. I
believe that's the problem causing my test case failed. The following
patch fixed this issue.
Signed-off-by: Aubrey.Li <aubreylee@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[KEY]: Fix conversion between IPSEC_MODE_xxx and XFRM_MODE_xxx.
We should not blindly convert between IPSEC_MODE_xxx and XFRM_MODE_xxx just
by incrementing / decrementing because the assumption is not true any longer.
Herbert Xu [Tue, 17 Apr 2007 19:28:27 +0000 (12:28 -0700)]
[NET]: Get rid of alloc_skb_from_cache
Since this was added originally for Xen, and Xen has recently (~2.6.18)
stopped using this function, we can safely get rid of it. Good timing
too since this function has started to bit rot.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
cache_k8_northbridges() is storing config values to incorrect locations
(in flush_words) and also its overflowing beyond the allocation, causing
slab verification failures.
IB/mthca: Fix data corruption after FMR unmap on Sinai
In mthca_arbel_fmr_unmap(), the high bits of the key are masked off.
This gets rid of the effect of adjust_key(), which makes sure that
bits 3 and 23 of the key are equal when the Sinai throughput
optimization is enabled, and so it may happen that an FMR will end up
with bits 3 and 23 in the key being different. This causes data
corruption, because when enabling the throughput optimization, the
driver promises the HCA firmware that bits 3 and 23 of all memory keys
will always be equal.
Fix by re-applying adjust_key() after masking the key.
Thanks to Or Gerlitz for reproducing the problem, and Ariel Shahar for
help in debug.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
[PATCH] x86: Fix potential overflow in perfctr reservation
While reviewing this code again I found a potential overflow of the bitmap.
The p4 oprofile can theoretically set bits beyond the reservation bitmap for
specific configurations. Avoid that by sizing the bitmaps properly.
Due to an over aggressive optimizer gcc 4.2 cannot optimize away _proxy_pda
in all cases (counter intuitive, but true). This breaks loading of some
modules.
The earlier workaround to just export a dummy symbol didn't work unfortunately
because the module code ignores exports with 0 value.
Fix logic error in VMI relocation processing. NOPs would always cause
a BUG_ON to fire because the != RELOCATION_NONE in the first if clause
precluding the == VMI_RELOCATION_NOP in the second clause. Make these
direct equality tests and just warn for unsupported relocation types
(which should never happen), falling back to native in that case.
NFS: Ensure PG_writeback is cleared when writeback fails
If the writebacks are cancelled via nfs_cancel_dirty_list, or due to the
memory allocation failing in nfs_flush_one/nfs_flush_multi, then we must
ensure that the PG_writeback flag is cleared.
Also ensure that we actually own the PG_writeback flag whenever we
schedule a new writeback by making nfs_set_page_writeback() return the
value of test_set_page_writeback().
The PG_writeback page flag ends up replacing the functionality of the
PG_FLUSHING nfs_page flag, so we rip that out too.
James Bottomley [Fri, 6 Apr 2007 16:14:56 +0000 (11:14 -0500)]
[SCSI] 3w-xxxx: fix oops caused by incorrect REQUEST_SENSE handling
3w-xxxx emulates a REQUEST_SENSE response by simply returning nothing.
Unfortunately, it's assuming that the REQUEST_SENSE command is
implemented with use_sg == 0, which is no longer the case. The oops
occurs because it's clearing the scatterlist in request_buffer instead
of the memory region.
This is fixed by using tw_transfer_internal() to transfer correctly to
the scatterlist.
Acked-by: adam radford <aradford@gmail.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Olaf Kirch [Fri, 13 Apr 2007 05:18:44 +0000 (01:18 -0400)]
DVB: dvb-usb-remote - fix oops when changing keymap
DVB USB remotes do not support changing keycode maps but set
input_dev->keycodesize and input_dev->keycodemax without setting
input_dev->keycode. This causes kernel oops when user tries to
look up (or change) current keymap.
While the proper fix would be to make remotes handle keymap changes
we'll just remove keycodemax and keycodesize initialization so
EVIOCGKEYCODE and EVIOCSKEYCODE will simply return -EINVAL.
David S. Miller [Fri, 13 Apr 2007 23:37:54 +0000 (16:37 -0700)]
[NETFILTER] arp_tables: Fix unaligned accesses.
There are two device string comparison loops in arp_packet_match().
The first one goes byte-by-byte but the second one tries to be
clever and cast the string to a long and compare by longs.
The device name strings in the arp table entries are not guarenteed
to be aligned enough to make this value, so just use byte-by-byte
for both cases.
Based upon a report by <drraid@gmail.com>.
Signed-off-by: David S. Miller <davem@davemloft.net>
A packet which is being discarded because of no routes in the
forwarding path should not be counted as OutNoRoutes but as
InNoRoutes.
Additionally, on this occasion, a packet whose destinaion is
not valid should be counted as InAddrErrors separately.
Based on patch from Mitsuru Chinen <mitch@linux.vnet.ibm.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
We are using size of security context from xfrm_policy to determine
how much space to alloc skb and then putting security context from
xfrm_state into skb. Should have been using size of security context
from xfrm_state to alloc skb. Following fix does that
Signed-off-by: Joy Latten <latten@austin.ibm.com> Acked-by: James Morris <jmorris@namei.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[VLAN]: Allow VLAN interface on top of bridge interface
When a VLAN interface is created on top of a bridge interface and
netfilter is enabled to see the bridged packets, the packets can be
corrupted when passing through the netfilter code. This is caused by the
VLAN driver not setting the 'protocol' and 'nh' members of the sk_buff
structure. In general, this is no problem as the VLAN interface is mostly
connected to a physical ethernet interface which does not use the
'protocol' and 'nh' members. For a bridge interface, however, these
members do matter.
Signed-off-by: Jerome Borsboom <j.borsboom@erasmusmc.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
While building a test kernel for the new esp driver (against
git-current), I hit this bug. Trivial fix, put the inline declaration
in the right place. :)
Signed-off-by: Tom "spot" Callaway <tcallawa@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
autofs_dentry_release() ends up clearing the ->dentry and ->inode members
of autofs_info before removing it from the rehash list. The list is
protected by the rehash lock in both functions, but since
autofs_dentry_release() starts tearing the autofs_info struct down before
removing it from the list, autofs_lookup_unhashed() can get a autofs_info
with a NULL dentry.
This patch moves the clearing of ->dentry and ->inode after the removal
from the rehash list.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Acked-by: Ian Kent <raven@themaw.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a bug in function decrementing a key of stat data item.
Offset of reiserfs keys are compared as signed values. To set key offset
to maximal possible value maximal signed value has to be used.
This bug is responsible for severe reiserfs filesystem corruption which
shows itself as warning vs-13060. reiserfsck fixes this corruption by
filesystem tree rebuilding.
Signed-off-by: Vladimir Saveliev <vs@namesys.com> Cc: <reiserfs-dev@namesys.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Neil Brown [Thu, 12 Apr 2007 06:28:44 +0000 (23:28 -0700)]
[PATCH] md: fix calculation for size of filemap_attr array in md/bitmap
If 'num_pages' were ever 1 more than a multiple of 8 (32bit platforms)
or of 16 (64 bit platforms). filemap_attr would be allocated one
'unsigned long' shorter than required. We need a round-up in there.
Signed-off-by: Neil Brown <neilb@suse.de> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] cciss: unregister from SCSI before tearing down device resources
We must unregister from SCSI before we unmap device resources and unhook
the IRQ handler. Otherwise, SCSI may send us more requests, and we won't
be able to handle them.
I see the following oops during every reboot of my HP DL360:
Randy Dunlap [Thu, 12 Apr 2007 06:28:41 +0000 (23:28 -0700)]
[PATCH] fix kernel oops with badly formatted module option
Catch malformed kernel parameter usage of "param = value". Spaces are not
supported, but don't cause a kernel fault on such usage, just report an
error.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Acked-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Thu, 12 Apr 2007 21:45:32 +0000 (14:45 -0700)]
[PKTGEN]: Add try_to_freeze()
The pktgen module prevents suspend-to-disk. Fix.
Acked-by: "Michal Piotrowski" <michal.k.k.piotrowski@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-eoan-kernel.git / log