Russell King [Mon, 10 Apr 2017 15:28:04 +0000 (16:28 +0100)]
net: mvmdio: disable interrupts in driver failure path
When the mvmdio driver has an interrupt, it enables the "done" interrupt
after requesting its interrupt handler. However, probe failure results
in the interrupt being left enabled. Disable it on the failure path.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilan Tayari [Fri, 7 Apr 2017 23:07:08 +0000 (02:07 +0300)]
gso: Support frag_list splitting with head_frag
A driver may use build_skb() for received packets.
These SKBs then have a head_frag.
Since commit d7e8883cfcf4 ("net: make GRO aware of
skb->head_frag"), GRO may build frag_list SKBs out of
head_frag received SKBs.
In such a case, the chained SKBs end up with a head_frag.
Commit 07b26c9454a2 ("gso: Support partial splitting at
the frag_list pointer") adds partial segmentation of frag_list
SKB chains into individual SKBs.
However, this is not done if the chained SKBs have any
linear part, because the device may not be able to DMA
the private linear buffer.
A chained frag_list SKB with head_frag is wrongfully
detected in this case as having a private linear part
and thus falls back to software GSO, while in fact the
linear part is backed by a DMA page just like any other frag.
This causes low performance when forwarding those packets
that were built with build_skb()
Allow partial segmentation at the frag_list pointer for
chained SKBs with head_frag.
Note that such SKBs can only be created by GRO, when applied
to received packets with head_frag.
Also note that this change only affects the data path that
performs the partial segmentation at frag_list pointer, and
not any of the other more common data paths.
Signed-off-by: Ilan Tayari <ilant@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp: define parameters of l2tp_session_get*() as "const"
Make l2tp_pernet()'s parameter constant, so that l2tp_session_get*() can
declare their "net" variable as "const".
Also constify "ifname" in l2tp_session_get_by_ifname().
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
This is v2 of the fourth batch of updates to the ftgmac100 driver.
This is a bunch of misc cleanups and fixes, such as properly
disabling HW checksum generation on AST2400 where it's known
to be broken and some chip init updates.
This also adds the ability to turn HW checksum on/off and
configure the ring sizes via ethtool.
v2 Fixes patch 1/10 (NETIF_F_HW_CSUM conversion)
The next (and last) batch will add a few more "features" such
as netpoll, multicast/promist, vlan offload...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ftgmac100: Make ring sizes configurable via ethtool
We set an arbitrary max at 1024 since we pre-allocate the actual
descriptor arrays and skb arrays to the full size to keep the
code a bit simpler and avoid allocation failures in the reset
task.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
ftgmac100: Disable HW checksum generation on AST2400, enable on others
We found out that HW checksum generation only works from AST2500
onward. This disables it on AST2400 and removes the "no-hw-checksum"
properties in the device-trees. The problem we had wasn't related
to NC-SI.
Also rework the logic testing for that property so it can be used
to disable HW checksum generation and checking regardless of whether
NC-SI is used or not in case other variants out there need this.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: do not use IB_SEND_INLINE together with mapped data
smc specifies IB_SEND_INLINE for IB_WR_SEND ib_post_send calls, but
provides a mapped buffer to be sent. This is inconsistent, since
IB_SEND_INLINE works without mapped buffer. Problem has not been
detected in the past, because tests had been limited to Connect X3 cards
from Mellanox, whose mlx4 driver just ignored the IB_SEND_INLINE flag.
For now, the IB_SEND_INLINE flag is removed.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure sockets never accepted are removed cleanly.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
unhash is already called in sock_put_work. Remove the second call.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: guarantee ConnClosed send after shutdown SHUT_WR
State SMC_CLOSED should be reached only, if ConnClosed has been sent to
the peer. If ConnClosed is received from the peer, a socket with
shutdown SHUT_WR done, switches errorneously to state SMC_CLOSED, which
means the peer socket is dangling. The local SMC socket is supposed to
switch to state APPFINCLOSEWAIT to make sure smc_close_final() is called
during socket close.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: no socket state changes in tasklet context
Several state changes occur during SMC socket closing. Currently
state changes triggered locally occur in process context with
lock_sock() taken while state changes triggered by peer occur in
tasklet context with bh_lock_sock() taken. bh_lock_sock() does not
wait till a lock_sock(() task in process context is finished. This
may lead to races in socket state transitions resulting in dangling
SMC-sockets, or it may lead to duplicate SMC socket freeing.
This patch introduces a closing worker to run all state changes under
lock_sock().
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Reported-by: Dave Jones <davej@codemonkey.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: always call the POLL_IN part of sk_wake_async
Wake up reading file descriptors for a closing socket as well, otherwise
some socket applications may stall.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: guarantee reset of write_blocked for heavy workload
If peer indicates write_blocked, the cursor state of the received data
should be send to the peer immediately (in smc_tx_consumer_update()).
Afterwards the write_blocked indicator is cleared.
If there is no free slot for another write request, sending is postponed
to worker smc_tx_work, and the write_blocked indicator is not cleared.
Therefore another clearing check is needed in smc_tx_work().
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
SMC requires an active ib port on the RoCE device.
smc_pnet_find_roce_resource() determines the matching RoCE device port
according to the configured PNET table. Do not return the found
RoCE device port, if it is not flagged active.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The global event handler is created only, if the ib_device has already
been used by at least one link group. It is guaranteed that there exists
the corresponding entry in the smc_ib_devices list. Get rid of this
superfluous check.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: stmmac: use netif_set_real_num_{rx,tx}_queues
In the submission of the lastest multiple buffer patch set, this fix was lost.
I am sending this patch to put it right again. The fix was originally proposed
by Arnd Bergmann.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Joao Pinto <jpinto@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Tue, 11 Apr 2017 18:08:08 +0000 (14:08 -0400)]
bpf: pass sk to helper functions
BPF helper functions access socket fields through skb->sk. This is not
set in ingress cgroup and socket filters. The association is only made
in skb_set_owner_r once the filter has accepted the packet. Sk is
available as socket lookup has taken place.
Temporarily set skb->sk to sk in these cases.
Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
devlink: fix return value check in devlink_dpipe_header_put()
Fix the return value check which testing the wrong variable
in devlink_dpipe_header_put().
Fixes: 1555d204e743 ("devlink: Support for pipeline debug (dpipe)") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 11 Apr 2017 18:51:36 +0000 (14:51 -0400)]
Merge branch 's390-qeth-updates'
Julian Wiedmann says:
====================
more s390/net updates
here's a second batch of s390/net patches for net-next.
A mixed bunch of qeth cleanups, and a few patches to add support for
ETHTOOL_GLINKSETTINGS.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
prepare() and complete() are not implemented by any discipline, so just
drop all the indirection.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Hans Wippel <hwippel@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
s390/qeth: use LINK_MODE_* to report the link characteristics
LINK_MODE_* replaces the u32-limited SUPPORTED_* / ENABLED_*
definitions.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
get_settings() is deprecated and lacks support for higher link
speeds, so implement get_link_ksettings() instead.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for moving to get_link_ksettings(), clean up how
we build the supported and advertised port/speed masks.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1. a buffer has 16 is_header flags, because that's its # of elements
2. replace the last occurrence of QETH_HEADER_SIZE, and remove it
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
s390/qeth: use correct return type for hard_start_xmit()
ndo_start_xmit() expects us to return netdev_tx_t here...
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
'elements_needed' is not used in qeth_do_send_packet_fast(),
so consequently remove it.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Identical code, we just need to call a layer-specific hook
to process any received buffer.
qeth_buffer_reclaim_work() is shuffled around to avoid a
forward declaration for qeth_queue_input_buffer().
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There's a number of layer-independent ioctls that we can handle
in core, and reduce code duplication. For layer-specific ioctls,
add a do_ioctl() discipline hook.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 11 Apr 2017 13:34:58 +0000 (15:34 +0200)]
bpf: remove struct bpf_map_type_list
There's no need to have struct bpf_map_type_list since
it just contains a list_head, the type, and the ops
pointer. Since the types are densely packed and not
actually dynamically registered, it's much easier and
smaller to have an array of type->ops pointer. Also
initialize this array statically to remove code needed
to initialize it.
In order to save duplicating the list, move it to the
types header file added by the previous patch and
include it in the same fashion.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 11 Apr 2017 13:34:57 +0000 (15:34 +0200)]
bpf: remove struct bpf_prog_type_list
There's no need to have struct bpf_prog_type_list since
it just contains a list_head, the type, and the ops
pointer. Since the types are densely packed and not
actually dynamically registered, it's much easier and
smaller to have an array of type->ops pointer. Also
initialize this array statically to remove code needed
to initialize it.
In order to save duplicating the list, move it to a new
header file and include it in the places needing it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 11 Apr 2017 18:36:28 +0000 (14:36 -0400)]
Merge branch 'fec-driver-code-clean'
Fugang Duan says:
====================
net: fec: driver code clean
The patch series are for fec ethernet driver code clean up, each patch is
independent.
Patch #1,#4,#5 are code clean up.
Patch #2,#3 are for aarch64 platform.
Patch #6 is for i.MX6UL to add lost errata workaround.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Many boards use i2c/spi expander gpio as phy-reset-gpios and these
gpios maybe registered after fec port, driver should check the return
value of .of_get_named_gpio().
Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In aarch64 system, the BD pointer is 64bit, and the high-order 32-bits
of the address is effective, so replace usigned with (void *) type to
aovid 64bit address is casted to 32bit in .fec_enet_get_nextdesc() and
.fec_enet_get_prevdesc() functions.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 11 Apr 2017 17:48:10 +0000 (13:48 -0400)]
Merge branch 'l2tp-drop-l2tp_session_find'
Guillaume Nault says:
====================
l2tp: drop l2tp_session_find()
l2tp_netlink is the last user of l2tp_session_find(), but that call is
useless. Let's remove it and drop l2tp_session_find() definitely.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp: remove useless duplicate session detection in l2tp_netlink
There's no point in checking for duplicate sessions at the beginning of
l2tp_nl_cmd_session_create(); the ->session_create() callbacks already
return -EEXIST when the session already exists.
Furthermore, even if l2tp_session_find() returns NULL, a new session
might be created right after the test. So relying on ->session_create()
to avoid duplicate session is the only sane behaviour.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Remove deprecated pci_enable_msix API in favour of its
successor pci_alloc_irq_vectors.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@cavium.com> Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: David S. Miller <davem@davemloft.net>
This is version 2 of the third batch of updates to
the ftgmac100 driver.
This one tackles the TX path of the driver. This provides the
bulk of the performance improvements by adding support for
fragmented sends along with a bunch of cleanups.
Version 2 fixes a patch splitting mistake and uses
eth_skb_pad() (which uses skb_put_padto) to pad ethernet
frames rather than skb_padto(), thus removing the need to
also pad the packet headlen in a couple of places.
Subsequent batches will add various features (ethtool functions,
vlan offlan, ...) and cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Directly access the fields when needed. The accessors add clutter
not clarity and in some cases cause unnecessary read-modify-write
type access on the slow (uncached) descriptor memory.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Those are non-cachable stores, let's avoid those we don't need. Remove
the helper, it's not particularly helpful and since it uses "priv"
I can't move it to the header file.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
ftgmac100: Split tx packet freeing from ftgmac100_tx_complete_packet()
This moves the packet freeing to a separate function
which is also used by ftgmac100_free_buffers() and will
be used more in the error path of fragmented sends.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
We have a private lock which isn't terribly useful, and we maintain
a "tx_pending" counter for information that's already available
via a trivial arithmetic operation. Then we unconditionaly wake
the queue even when not stopped. Finally our code in tx isn't
really safe vs. a concurrent reclaim. The aspeed chips aren't SMP
today but I prefer the code being right and future proof.
So rip that out and replace it with more "standard" queue handling,
currently with a threshold of 1 queue element, which will be
increased when we implement fragmented sends.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than in the descriptor. The descriptor is mapped non-cachable
and rather slow to access.
Since to do that we need to keep track of the tx "pointer" we also
have no use of all the accesors to manipulate it, just open code
it, it's as clear and will help when adding fragmented sends.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: mt7530: Include gpio/consumer.h for GPIO functions
Fixes build errors seen with CONFIG_GPIOLIB disabled and warnings enabled:
drivers/net/dsa/mt7530.c: In function 'mt7530_setup':
drivers/net/dsa/mt7530.c:948:3: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror=implicit-function-declaration]
gpiod_set_value_cansleep(priv->reset, 0);
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/mt7530.c: In function 'mt7530_probe':
drivers/net/dsa/mt7530.c:1068:17: error: implicit declaration of function 'devm_gpiod_get_optional' [-Werror=implicit-function-declaration]
priv->reset = devm_gpiod_get_optional(&mdiodev->dev, "reset",
^~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/mt7530.c:1069:13: error: 'GPIOD_OUT_LOW' undeclared (first use in this function)
GPIOD_OUT_LOW);
^~~~~~~~~~~~~
drivers/net/dsa/mt7530.c:1069:13:
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
o s/bpf_bpf_get_socket_cookie/bpf_get_socket_cookie
Signed-off-by: Alexander Alemayhu <alexander@alemayhu.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
As per discussion between Roopa Prabhu and David Ahern, it is
advisable that we instead have the code collect the setlink triggered
events into a bitmask emitted in the IFLA_EVENT netlink attribute.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 9 Apr 2017 20:41:06 +0000 (13:41 -0700)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-04-08
This series contains updates to i40e and i40evf only.
Mitch fixes an issue where the client driver (i40iw) was attempting to
load on x710 devices (which do not support iWARP), so only register with
the client if iWARP is supported.
Jake fixes up error messages to better clarify to the user when adding a
invalid flow type. Updates the driver to look up the MAC address from
eth_get_platform_mac_address() first before checking what the firmware
provides. Cleans up code so we are not repeating a duplicate loop, by
checking both transmit and receive queues in a single loop. Also cleans
up flags never used, so remove the definitions.
Alex does cleanup so that we are always updating pf->flags when a change
is made to the private flags. Adds support for 3K buffers to the receive
path so that we can provide the additional padding needed in the event
of NET_IP_ALIGN being non-zero or a cache line being greater than 64.
Adds support for build_skb() to i40e/i40evf.
Maciej adjusts the scope of the rtnl lock held during reset because it
was stopping other PFs from running their reset procedures.
Alan reduces code complexity in i40e_detect_recover_hung_queue().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series does factor the common code found in all tag implementations
into dsa_switch_rcv(). The original motivation was to add GRO support, but this
may be a lot of work with unclear benefits at this point.
Changes in v2:
- take care of tag_mtk.c in the process
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
All DSA tag receive functions need to unshare the skb before mangling it, move
this to the generic dsa_switch_rcv() function which will allow us to make the
tag receive function return their mangled skb without caring about freeing a
NULL skb.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
All available gso_type flags are currently in use, so
extend gso_type from 'unsigned short' to 'unsigned int'
to be able to add further flags.
We reorder the struct skb_shared_info to use
two bytes of the four byte hole before dataref.
All fields before dataref are cleared, i.e.
four bytes more than before the change.
The remaining two byte hole is moved to the
beginning of the structure, this protects us
from immediate overwites on out of bound writes
to the sk_buff head.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Manlunas [Fri, 7 Apr 2017 02:22:22 +0000 (19:22 -0700)]
liquidio: fix VF incorrectly indicating that it successfully set its VLAN
For security reasons, NIC firmware does not allow VF to set its VLAN if PF
set it already. Firmware allows VF to set its VLAN if PF did not set it.
After the VF instructs the firmware to set the VLAN, VF always indicates
(via return 0) that the operation is successful--even for the times when it
isn't.
Put in a mechanism for the VF's set VLAN function to receive the firmware
response code, then make that function return -EPERM if the firmware
forbids the operation.
Make that mechanism available for other functions that may, in the future,
be interested in receiving the response code from the firmware. That
mechanism involves adding new fields to struct octnic_ctrl_pkt, so make all
users of struct octnic_ctrl_pkt initialize the struct to zero before using
it; otherwise, the mechanism might act on uninitialized garbage.
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by: Derek Chickles <derek.chickles@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netvsc: Initialize all channel related state prior to opening the channel
Prior to opening the channel we should have all the state setup to handle
interrupts. The current code does not do that; fix the bug. This bug
can result in faults in the interrupt path.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: mv88e6xxx: Make SMI c22/c45 read/write functions static
The SMI clause 22 & 45 read/write operations are local to the global2.c file,
so make them static. This eliminates the following warning:
drivers/net/dsa/mv88e6xxx/global2.c:571:5: warning: no previous prototype for 'mv88e6xxx_g2_smi_phy_read_c45' [-Wmissing-prototypes]
int mv88e6xxx_g2_smi_phy_read_c45(struct mv88e6xxx_chip *chip, int addr,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.c:602:5: warning: no previous prototype for 'mv88e6xxx_g2_smi_phy_read_c22' [-Wmissing-prototypes]
int mv88e6xxx_g2_smi_phy_read_c22(struct mv88e6xxx_chip *chip, int addr,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.c:635:5: warning: no previous prototype for 'mv88e6xxx_g2_smi_phy_write_c45' [-Wmissing-prototypes]
int mv88e6xxx_g2_smi_phy_write_c45(struct mv88e6xxx_chip *chip, int addr,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.c:664:5: warning: no previous prototype for 'mv88e6xxx_g2_smi_phy_write_c22' [-Wmissing-prototypes]
int mv88e6xxx_g2_smi_phy_write_c22(struct mv88e6xxx_chip *chip, int addr,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Suggested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Thu, 6 Apr 2017 14:10:42 +0000 (16:10 +0200)]
netlink: uapi: use hex numbers for NLM_F_* flags
It's rather confusing that the netlink message flags are
numbered 1, 2, 4, 8, 16, 32, <unused>, 0x100. Make that
more understandable by numbering the lower ones with hex
constants as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Thu, 6 Apr 2017 12:54:35 +0000 (13:54 +0100)]
nfp: don't dereference a null nn->eth_port to print a warning
On the case where nn->eth_port is null the warning message
is printing the port by dereferencing this null pointer.
Remove the deference to avoid a crash when printing the
warning message.
Detected by CoverityScan, CID#1426198 ("Dereference after null check")
Fixes: ce22f5a2cbe3c627 ("nfp: separate high level and low level NSP headers") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 8 Apr 2017 15:07:02 +0000 (08:07 -0700)]
Merge branch 'net-SO_COOKIE'
Chenbo Feng says:
====================
New getsockopt option to retrieve socket cookie
In the current kernel socket cookie implementation, there is no simple
and direct way to retrieve the socket cookie based on file descriptor. A
process mat need to get it from sock fd if it want to correlate with
sock_diag output or use a bpf map with new socket cookie function.
If userspace wants to receive the socket cookie for a given socket fd,
it must send a SOCK_DIAG_BY_FAMILY dump request and look for the 5-tuple.
This is slow and can be ambiguous in the case of sockets that have the
same 5-tuple (e.g., tproxy / transparent sockets, SO_REUSEPORT sockets,
etc.).
As shown in the example program. The xt_eBPF program is using socket cookie
to record the network traffics statistics and with the socket cookie
retrieved by getsockopt. The program can directly access to a specific
socket data without scanning the whole bpf map.
====================
Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Added a per socket traffic monitoring option to illustrate the usage
of new getsockopt SO_COOKIE. The program is based on the socket traffic
monitoring program using xt_eBPF and in the new option the data entry
can be directly accessed using socket cookie. The cookie retrieved
allow us to lookup an element in the eBPF for a specific socket.
Signed-off-by: Chenbo Feng <fengc@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new getsockopt operation to retrieve the socket cookie
for a specific socket based on the socket fd. It returns a unique
non-decreasing cookie for each socket.
Tested: https://android-review.googlesource.com/#/c/358163/
Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Chenbo Feng <fengc@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 8 Apr 2017 13:18:00 +0000 (06:18 -0700)]
Merge tag 'mlx5-updates-2017-04-16' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-04-16
This patchset provides some updates for the mlx5 drivers.
From Majd,
1st patch, Adds ConnectX-6 and ConnectX-6 VF PCI IDs support.
From Guy,
2nd patch, Adds RXFCS scatter support.
3rd patch, Small cleanup to make a function static.
From Eran,
4th patch, Adds 4 zeros padding to ethtool FW version.
6th patch, Trevial code reuse cleanup
From Inbar,
5th patch, Show board id in ethtool driver information
From Saeed,
7th patch, Set default RX moderation parameters on driver load
as a small fix for the latest fail-safe config feature.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 5 Apr 2017 11:51:03 +0000 (07:51 -0400)]
i40e/i40evf: Use build_skb to build frames
This patch is meant to improve the performance of the Rx path.
Specifically by using build_skb we have several distinct advantages.
In the case of small frames we were previously using a copy-break approach.
This means that we were allocating a page fragment to use for skb->head,
and were having to copy the packet into that region. Both of those calls
are now avoided since we just build the skb around the data.
In the case of large frames the gains are much more significant.
Specifically we were having to allocate skb->head, and copy the headers as
before. However in addition we were having to parse the header using
eth_get_headlen which could be quite expensive. All of this is avoided by
building the frame around the data. I have seen gains as high as 30% when
using VXLAN for instance due to just header pulling overhead.
Finally with all this in place it also sets us up to start looking at
enabling XDP. Specifically we now have a path in which the data is in the
page and the frame is built around it. So if we parse it with XDP before
we call build_skb we can take care of any necessary processing there.
Change-ID: Id4bdd618e94473d41f892417e5d8019639e421e3 Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 5 Apr 2017 11:51:02 +0000 (07:51 -0400)]
i40e/i40evf: Add support for padding start of frames
This patch adds padding to the start of frames to make room for headroom
for us to eventually start using build_skb. Right now we guarantee at
least NET_SKB_PAD + NET_IP_ALIGN, however we allocate more space if more is
available. For example on x86 the headroom should be 192 bytes.
On systems that have too large of a cache line size to support storing 1.5K
padding and shared info we default to using 3K buffers and reserve
everything that isn't used for skb_shared_info or the data buffer for
headroom.
Change-ID: I33c641c9a1ea10cf7cc484c2d20985368d2d709a Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 5 Apr 2017 11:51:01 +0000 (07:51 -0400)]
i40e/i40evf: Add support for using order 1 pages with a 3K buffer
There are situations where adding padding to the front and back of an Rx
buffer will require that we add additional padding. Specifically if
NET_IP_ALIGN is non-zero, or the MTU size is larger than 7.5K we would need
to use 2K buffers which leaves us with no room for the padding.
To preemptively address these cases I am adding support for 3K buffers to
the Rx path so that we can provide the additional padding needed in the
event of NET_IP_ALIGN being non-zero or a cache line being greater than 64.
Change-ID: I938bc1ba611285428df39a613cd66f98e60b55c7 Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 5 Apr 2017 11:51:00 +0000 (07:51 -0400)]
i40e: clean up historic deprecated flag definitions
Since an early commit a few flags have no longer
been used. Remove these definitions to reduce code clutter.
Change-ID: I3589be4622574e747013cd4dc403e18b039f4965 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alice Michael [Sat, 8 Apr 2017 06:01:35 +0000 (23:01 -0700)]
i40e: remove I40E_FLAG_NEED_LINK_UPDATE
The I40E_FLAG_NEED_LINK_UPDATE was never used. Remove the flag
definitions.
Change-ID: If59d0c6b4af85ca27281f3183c54b055adb439a4 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
projects / mirror_ubuntu-focal-kernel.git / log