Martin Bachem [Tue, 15 May 2012 23:51:04 +0000 (23:51 +0000)]
mISDN: Bugfix hfcsusb: usb endpoint activation/deactivation
Here was a off by one in the activation/deactivation.
The additional activation in open_bchannel() did hide
it, but only if you do not try to use B2.
Signed-off-by: Martin Bachem <info@colognechip.com> Signed-off-by: Karsten Keil <kkeil@linux-pingi.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Keil [Tue, 15 May 2012 23:51:03 +0000 (23:51 +0000)]
mISDN: avmfritz use the bigger fifo of chip version 2
If we detect the latest hardware revision we should use the bigger fifo
to avoid TX underruns and have less interrupts.
TX underruns should be logged as warning.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Keil [Tue, 15 May 2012 23:51:01 +0000 (23:51 +0000)]
mISDN: Cleanup channel also if it already was deactivated
If a channel was closed after it was deactivated it could happen that
something was not proper resetted. The test if a channel is still activ
was wrong, so remove it and always do the cleanup.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Support for monitor device intended to capture all the network activity.
This interface could be used by networks sniffers and is already
supported by WireShark. That's a good test point to check that basic
MAC support works.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This stack implementation distinguishes several types of slave
interfaces. Another parameter to 'add_iface_' function is added
to clarify the interface type is going to be registered.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Slaves represent typical network interfaces available from userspace.
Each ieee802154 device/transceiver may have several slaves and able
to be associated with several networks at the same time. So this
patch adds structure for slaves declaration.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
According IEEE 802.15.4 standard each node can be either full functionality
device (FFD) or reduce functionality device (RFD). So 2 sets of operations
are needed. This patch declare RFD operations structure.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The IEEE 802.15.4 Working Group focuses on the standardization of the
bottom two layers of ISO/OSI protocol stack: Physical (PHY) and MAC.
The MAC layer provides access control to a shared channel and reliable
data delivery. The main functions performed by the MAC sublayer are:
association and disassociation, security control, optional star
network topology functions, such as beacon generation and Guaranteed
Time Slots (GTSs) management, generation of ACK frames (if used), and,
finally, application support for the two possible network topologies
described in the standard.
This is an initial commit which describes main data structures needed
for ieee802.15.4 compatible devices representation in the MAC layer.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Tue, 15 May 2012 14:11:53 +0000 (14:11 +0000)]
net: ipv6: Standardize prefixes for message logging
Add #define pr_fmt(fmt) as appropriate.
Add "IPv6: " to appropriate files.
Convert printk(KERN_<LEVEL> to pr_<level> (but not KERN_DEBUG).
Standardize on "%s: " not "%s(): " when emitting __func__.
Use "%s: ", __func__ instead of embedding function name.
Coalesce formats, align arguments.
ADDRCONF output is now prefixed with "IPv6: "
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Daney [Tue, 15 May 2012 10:46:52 +0000 (10:46 +0000)]
netdev/phy: Make get_phy_id() static and quit EXPORTing it.
This function is only referenced from within phy_device.c, so there is
no reason to export it. In fact, we can make it static.
Signed-off-by: David Daney <david.daney@cavium.com> Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Tue, 15 May 2012 10:35:04 +0000 (10:35 +0000)]
net/mlx4_core: Fixed error flow in rem_slave_eqs
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Tue, 15 May 2012 10:35:03 +0000 (10:35 +0000)]
net/mlx4_core: Add XRC domains and counters to resource tracker
Add missing resource tracking for XRC domains and complete the tracking for HCA
network flow counters.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Tue, 15 May 2012 10:35:02 +0000 (10:35 +0000)]
net/mlx4_core: Fix potential kernel Oops in res tracker during Dom0 driver unload
Currently the slave and master resources are deleted after master freed
all bitmaps. If any resources were not properly cleaned up during the
shutdown process, an Oops would result.
Fix so that delete slave (only) resources during cleanup. Master resources
are cleaned up during unload process, and need not separately be cleaned.
Note that during cleanup, we need to split the resource-tracker freeing
functionality.
Before removing all the bitmaps, we free any leftover slave resources.
However, we can only remove the resource tracker linked list after
all bitmap frees, since some of the freeing functions (e.g.,
mlx4_cleanup_eq_table) use paravirtualized FW commands which expect
the resource tracker linked list to be present.
Found-by: Aviad Yehezkel <aviadye@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Tue, 15 May 2012 10:35:01 +0000 (10:35 +0000)]
net/mlx4_core: Do not reset module-parameter num_vfs when fail to enable sriov
Consider the following scenario: 2 HCAs, where only one of which can run SRIOV.
If we reset the module parameter, all the VFs of the SRIOV HCA will be
claimed by the PPF host (-- the code relies on num_vfs being non-zero
to avoid this claiming, and num_vfs was reset when pci_enable_sriov failed
for the non-SRIOV HCA).
The solution is not to touch the num_vfs parameter.
Also, eliminate the unneeded check of num_vfs when disabling sriov
(the dev flag bit is sufficient).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Tue, 15 May 2012 10:35:00 +0000 (10:35 +0000)]
net/mlx4_core: Remove unused *_str functions from the resource tracker
Removed unsued *_str helper functions from resource_tracker.c
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Tue, 15 May 2012 10:34:59 +0000 (10:34 +0000)]
net/mlx4_core: Change SYNC_TPT to be native (not wrapped)
The "wrapped" was incorrect, since no wrapper function was defined.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Tue, 15 May 2012 10:34:58 +0000 (10:34 +0000)]
net/mlx4_core: Fix init_port mask state for slaves
In function mlx4_INIT_PORT_wrapper, the port state mask for the
slave is only set if we are invoking the INIT_PORT fw command.
However, the reference count for the (initialized) port is
incremented anyway.
This creates a problem in that when we have multiple slaves,
then the CLOSE_PORT command will never be invoked. The
reason is that in the CLOSE_PORT wrapper, if the port-state
mask is zero for the slave (which it is), the wrapper returns
without doing anything. The only slave which will not return
immediately in the CLOSE_PORT wrapper is that slave for which
INIT_PORT was invoked.
The fix is to not have the port-state mask setting depend
on the logic for calling the INIT_PORT fw command.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Tue, 15 May 2012 10:34:57 +0000 (10:34 +0000)]
net/mlx4: Address build warnings on set but not used variables
Handle the compiler warnings on variables which are set but not used
by removing the relevant variable or casting a return value which is
ignored on purpose to void.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Gortmaker [Thu, 10 May 2012 02:41:59 +0000 (22:41 -0400)]
tokenring: delete all remaining driver support
This represents the mass deletion of the of the tokenring support.
It gets rid of:
- the net/tr.c which the drivers depended on
- the drivers/net component
- the Kbuild infrastructure around it
- any tokenring related CONFIG_ settings in any defconfigs
- the tokenring headers in the include/linux dir
- the firmware associated with the tokenring drivers.
- any associated token ring documentation.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Paul Gortmaker [Thu, 10 May 2012 21:14:35 +0000 (17:14 -0400)]
net: delete all instances of special processing for token ring
We are going to delete the Token ring support. This removes any
special processing in the core networking for token ring, (aside
from net/tr.c itself), leaving the drivers and remaining tokenring
support present but inert.
The mass removal of the drivers and net/tr.c will be in a separate
commit, so that the history of these files that we still care
about won't have the giant deletion tied into their history.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Joe Perches [Sun, 13 May 2012 21:56:25 +0000 (21:56 +0000)]
net: Add net_ratelimited_function and net_<level>_ratelimited macros
__ratelimit() can be considered an inverted bool test because
it returns true when not ratelimited. Several tests in the
kernel tree use this __ratelimit() function incorrectly.
No net_ratelimit uses are incorrect currently though.
Most uses of net_ratelimit are to log something via printk or
pr_<level>.
In order to minimize the uses of net_ratelimit, and to start
standardizing the code style used for __ratelimit() and net_ratelimit(),
add a net_ratelimited_function() macro and net_<level>_ratelimited()
logging macros similar to pr_<level>_ratelimited that use the global
net_ratelimit instead of a static per call site "struct ratelimit_state".
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alan Cox [Mon, 14 May 2012 03:57:31 +0000 (03:57 +0000)]
dummy: documentation is stale
dummy0/1/2 names are always used and there are options to set multiple
dummy devices. Remove the obsolete text
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42865 Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Beulich [Tue, 15 May 2012 01:57:44 +0000 (01:57 +0000)]
xfrm: make xfrm_algo.c a module
By making this a standalone config option (auto-selected as needed),
selecting CRYPTO from here rather than from XFRM (which is boolean)
allows the core crypto code to become a module again even when XFRM=y.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish chopra [Tue, 15 May 2012 01:13:38 +0000 (01:13 +0000)]
linux/ethtool: Added macro ETH_FW_DUMP_DISABLE
o flag field of ethtool_dump structure must be initialized by this macro
value that is zero, if the firmware dump is disabled.
by this we can get the firmware dump capability [enable/disable] via ethtool
Signed-off-by: Manish chopra <manish.chopra@qlogic.com> Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Upon resume from standby, there is a possible interrupt
unsafe locking scenario raised when configure the Kernel
with CONFIG_PROVE_LOCKING. So this patch fixes that in
PM driver stuff by calling lock/unlock_irqsave/restore.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In mixed burst (MB) mode, the AHB master always initiates
the bursts with fixed-size when the DMA requests transfers
of size less than or equal to 16 beats.
This patch adds the MB support and the flag that can be
passed from the platform to select it.
MB mode can also give some benefits in terms of performances
on some platforms.
v2: fixed Coding Style
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac: extend mac addr reg and fix perfect filering
This patch is to extend the number of MAC address registers
for 16 to 32. In fact, other new 16 registers are available in new
chips and this can help on perfect filter mode for unicast.
This patch also fixes the perfect filtering mode by setting the
bit 31 in the MAC address registers.
v2: fixed Coding Style.
Signed-off-by: Gianni Antoniazzi <gianni.antoniazzi-ext@st.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 12 May 2012 21:23:23 +0000 (21:23 +0000)]
codel: use u16 field instead of 31bits for rec_inv_sqrt
David pointed out gcc might generate poor code with 31bit fields.
Using u16 is more than enough and permits a better code output.
Also make the code intent more readable using constants, fixed point arithmetic
not being trivial for everybody.
Suggested-by: David Miller <davem@davemloft.net> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 14 May 2012 22:15:33 +0000 (18:15 -0400)]
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
* an improvement to avoid to linearise the whole received packet when not needed
* an improvement for client traffic rerouting after roaming
* a fix for the local translation table state-machine
* minor cleanups and fixes
Sasha Levin [Mon, 14 May 2012 11:57:06 +0000 (11:57 +0000)]
net: codel: fix build errors
Fix the following build error:
net/sched/sch_fq_codel.c: In function 'fq_codel_dump_stats':
net/sched/sch_fq_codel.c:464:3: error: unknown field 'qdisc_stats' specified in initializer
net/sched/sch_fq_codel.c:464:3: warning: missing braces around initializer
net/sched/sch_fq_codel.c:464:3: warning: (near initialization for 'st.<anonymous>')
net/sched/sch_fq_codel.c:465:3: error: unknown field 'qdisc_stats' specified in initializer
net/sched/sch_fq_codel.c:465:3: warning: excess elements in struct initializer
net/sched/sch_fq_codel.c:465:3: warning: (near initialization for 'st')
net/sched/sch_fq_codel.c:466:3: error: unknown field 'qdisc_stats' specified in initializer
net/sched/sch_fq_codel.c:466:3: warning: excess elements in struct initializer
net/sched/sch_fq_codel.c:466:3: warning: (near initialization for 'st')
net/sched/sch_fq_codel.c:467:3: error: unknown field 'qdisc_stats' specified in initializer
net/sched/sch_fq_codel.c:467:3: warning: excess elements in struct initializer
net/sched/sch_fq_codel.c:467:3: warning: (near initialization for 'st')
make[1]: *** [net/sched/sch_fq_codel.o] Error 1
Signed-off-by: Sasha Levin <levinsasha928@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched/sch_codel.c: In function ‘dequeue’:
net/sched/sch_codel.c:70: error: implicit declaration of function ‘prefetch’
make[1]: *** [net/sched/sch_codel.o] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
batman-adv: unset the TT_CLIENT_PENDING flag if the new local entry already exists
When trying to add a new tt_local_entry, if such entry already exists, we have
to ensure that the TT_CLIENT_PENDING flag is not set, otherwise the entry will
be deleted soon.
Reported-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Sven Eckelmann [Mon, 2 Apr 2012 17:31:26 +0000 (19:31 +0200)]
batman-adv: README cleanups
- Add routing_algo
- Remove date from README:
The date has to be updated when a patch touches the README. Therefore, nearly
every feature will modify this date. It can happens quite often that not only
one feature is currently in development or waiting on the mailinglist. This
creates merge conflicts when applying a patchset.
The date itself doesn't provide any additional information when this file is
only available in a release tarball or as part of a SCM repository.
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Marek Lindner [Sat, 17 Mar 2012 07:28:33 +0000 (15:28 +0800)]
batman-adv: refactor window_protected to avoid unnecessary return statement
Reported-by: David Laight <David.Laight@aculab.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
In case of a client X roaming from a generic node A to another node B, it is
possible that a third node C gets A's OGM but not B's. At this point in time, if
C wants to send data to X it will send a unicast packet destined to A. The
packet header will contain A's last ttvn (C got A's OGM and so it knows it).
The packet will travel towards A without being intercepted because the ttvn
contained in its header is the newest for A.
Once A will receive the packet, A's state will not report to be in a "roaming
phase" (because, after a roaming, once A sends out its OGM, all the changes are
committed and the node is considered not to be in the roaming state anymore)
and it will match the ttvn carried by the packet. Therefore there is no reason
for A to try to alter the packet's route, thus dropping the packet because the
destination client is not there anymore.
However, C is well aware that it's routing information towards the client X is
outdated as it received an OGM from A saying that the client roamed away.
Thanks to this detail, this patch introduces a small change in behaviour: as
long as C is in the state of not knowing the new location of client X it will
forward the traffic to its last known location using ttvn-1 of the destination.
By using an older ttvn node A will be forced to re-route the packet.
Intermediate nodes are also allowed to update the packet's destination as long
as they have the information about the client's new location.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Carolyn Wyborny [Sun, 4 Mar 2012 03:26:26 +0000 (03:26 +0000)]
igb: Add function and pointers for 82580 low power state settings.
82580 and later parts did not have low power setting functions. This patch
adds the specific functions, pointers and assignments for these low
power settings.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Eric Dumazet [Fri, 11 May 2012 09:30:50 +0000 (09:30 +0000)]
fq_codel: Fair Queue Codel AQM
Fair Queue Codel packet scheduler
Principles :
- Packets are classified (internal classifier or external) on flows.
- This is a Stochastic model (as we use a hash, several flows might
be hashed on same slot)
- Each flow has a CoDel managed queue.
- Flows are linked onto two (Round Robin) lists,
so that new flows have priority on old ones.
- For a given flow, packets are not reordered (CoDel uses a FIFO)
- head drops only.
- ECN capability is on by default.
- Very low memory footprint (64 bytes per flow)
tc qdisc ... fq_codel [ limit PACKETS ] [ flows number ]
[ target TIME ] [ interval TIME ] [ noecn ]
[ quantum BYTES ]
PING 172.30.42.18 (172.30.42.18) 56(84) bytes of data.
64 bytes from 172.30.42.18: icmp_req=1 ttl=64 time=0.227 ms
64 bytes from 172.30.42.18: icmp_req=2 ttl=64 time=0.165 ms
64 bytes from 172.30.42.18: icmp_req=3 ttl=64 time=0.166 ms
64 bytes from 172.30.42.18: icmp_req=4 ttl=64 time=0.151 ms
64 bytes from 172.30.42.18: icmp_req=5 ttl=64 time=0.164 ms
64 bytes from 172.30.42.18: icmp_req=6 ttl=64 time=0.172 ms
64 bytes from 172.30.42.18: icmp_req=7 ttl=64 time=0.175 ms
64 bytes from 172.30.42.18: icmp_req=8 ttl=64 time=0.183 ms
64 bytes from 172.30.42.18: icmp_req=9 ttl=64 time=0.158 ms
64 bytes from 172.30.42.18: icmp_req=10 ttl=64 time=0.200 ms
10 packets transmitted, 10 received, 0% packet loss, time 8999ms
rtt min/avg/max/mdev = 0.151/0.176/0.227/0.022 ms
Much better than SFQ because of priority given to new flows, and fast
path dirtying less cache lines.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the Newton method and reciprocal divide.
Total cost is 15 cycles instead of 120 on my Corei5 machine (64bit
kernel).
There is a small 'error' for count values < 5, but we don't really care.
I reuse a hole in struct codel_vars :
- pack the dropping boolean into one bit
- use 31bit to store the reciprocal value of sqrt(count).
Suggested-by: Van Jacobson <van@pollere.net> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Dave Taht <dave.taht@bufferbloat.net> Cc: Kathleen Nichols <nichols@pollere.com> Cc: Tom Herbert <therbert@google.com> Cc: Matt Mathis <mattmathis@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Nandita Dukkipati <nanditad@google.com> Cc: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jussi Kivilinna [Fri, 11 May 2012 22:17:57 +0000 (22:17 +0000)]
rndis_wlan: cleanup: change oid from __le32 to u32 in various places
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jussi Kivilinna [Fri, 11 May 2012 22:17:50 +0000 (22:17 +0000)]
rndis_host: cleanup: change oid from __le32 to u32 in rndis_query()
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jussi Kivilinna [Fri, 11 May 2012 22:17:42 +0000 (22:17 +0000)]
rndis_wlan: cleanup: byteswap data from device instead of RNDIS_* defines
All other values from device provided buffer are byteswapped, so it seems more
logical to do same for these.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jussi Kivilinna [Fri, 11 May 2012 22:17:34 +0000 (22:17 +0000)]
rndis_host: cleanup: byteswap data from device instead of RNDIS_* defines
All other values from device provided buffer are byteswapped, so it seems
more logical to do same for these.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij [Fri, 11 May 2012 22:17:07 +0000 (22:17 +0000)]
usb/net: rndis: merge command codes
Switch the hyperv filter and rndis gadget driver to use the same command
enumerators as the other drivers and delete the surplus command codes.
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij [Fri, 11 May 2012 22:16:54 +0000 (22:16 +0000)]
usb/net: rndis: move and namespace PnP defines
This moves the PnP OID definitions to the RNDIS_* namespace
and puts them in the next falling slot in the list. Oh, the comment
above the PnP defines was referring to some obsolete or out-of-tree
driver so removed it, and removed my own comments telling where each
header segment came from as well, we have moved everything around by
this point anyway.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij [Fri, 11 May 2012 22:16:39 +0000 (22:16 +0000)]
usb/net: rndis: merge media type definitions
Let's have a unified table of RNDIS media. We used to have a similar
table with NDIS_* prefix from the gadget driver, but since we're only
using RNDIS in the kernel (IIRC NDIS, non-remote, is for the windows-
internal network drivers so what do we care) let's prefix everything
with RNDIS. Some of the definitions were conflicting, in one of the
defines 0x0B is bearer "CO WAN" and in two others "BPC". Well I took
the majority vote. Two definition of medium 0x09 calls it "wireless
WAN" but one vote for "wireless LAN" but in this case I am sticking
with the minority, "Wide Area Network" does not make much sense in
this case as far as I can tell.
NOTE: latin singular and plural is so screwed up in these defines
that it makes my eyes bleed. But I will not attempt to submit a
patch converting all use of _MEDIA_ to _MEDIUM_ while I can probably
tell from the semantics of the code that RNDIS_MEDIA_STATE_CONNECTED
is most probably (erroneously) referring to a singular, unless it
can return an array of connected media. I suspect these erroneous
plurals are used in documentation and such so I don't want to
mess around with things for no functional change.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij [Fri, 11 May 2012 22:16:08 +0000 (22:16 +0000)]
usb/net: rndis: eliminate first set of duplicate OIDs
The RNDIS protocol contains a vast number of Object ID:s (OIDs).
The current definitions had multiple definitions of these ID:s,
let's use the nicely RNDIS_*-prefixed defines from the HyperV
implementation, rename everywhere they're used, and copy+rename
the few that were missing from this list of objects.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij [Fri, 11 May 2012 22:15:59 +0000 (22:15 +0000)]
usb/net: rndis: remove ambigous status codes
The RNDIS status codes are redefined with much stranged ifdeffery
and only one of these codes was used in the hyperv driver, and
there it is very clearly referring to the RNDIS variant, not some
other status. So clarify this by explictly using the RNDIS_*
prefixed status code in the hyperv drivera and delete the
duplicate defines.
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij [Fri, 11 May 2012 22:15:50 +0000 (22:15 +0000)]
usb/net: rndis: break out <linux/rndis.h> defines
As a first step to consolidate the RNDIS implementations, break out
a common file with all the #defines and move it to <linux/rndis.h>.
This also deletes the immediate duplicated defines in the
<linux/rndis.h> file that yields a lot of compilation warnings.
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij [Fri, 11 May 2012 22:15:39 +0000 (22:15 +0000)]
usb/net: rndis: inline the cpu_to_le32() macro
The header file <linux/usb/rndis_host.h> used a number of #defines
that included the cpu_to_le32() macro to assure the result will be
in LE endianness. Inlining this into the code instead of using it
in the code definitions yields consolidation opportunities later
on as you will see in the following patches. The individual
drivers also used local defines - all are switched over to the
pattern of doing the conversion at the call sites instead.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eldad Zack [Sat, 5 May 2012 10:13:53 +0000 (10:13 +0000)]
net/ipv6/af_inet6.c: checkpatch cleanup
af_inet6.c:80: ERROR: do not initialise statics to 0 or NULL
af_inet6.c:259: ERROR: spaces required around that '=' (ctx:VxV)
af_inet6.c:394: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
af_inet6.c:412: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
af_inet6.c:422: ERROR: do not use assignment in if condition
af_inet6.c:425: ERROR: do not use assignment in if condition
af_inet6.c:433: ERROR: do not use assignment in if condition
af_inet6.c:437: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
af_inet6.c:446: ERROR: spaces required around that '=' (ctx:VxV)
af_inet6.c:478: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
af_inet6.c:485: ERROR: that open brace { should be on the previous line
af_inet6.c:485: ERROR: space required before the open parenthesis '('
af_inet6.c:513: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
af_inet6.c:629: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
af_inet6.c:647: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
af_inet6.c:687: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
af_inet6.c:709: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
af_inet6.c:1073: ERROR: space required before the open parenthesis '('
Signed-off-by: Eldad Zack <eldad@fogrefinery.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Randy Dunlap <rdunlap@xenotime.net> Cc: David Daney <david.daney@cavium.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Acked-by: David Daney <david.daney@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 11 May 2012 21:57:52 +0000 (17:57 -0400)]
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
* fix a little bug in the DHCP packet snooping introduced so far
* minor fixes and cleanups
* minor routing protocol API cleanups
* add a new contributor name to translation-table.{c,h}
* update copyright years in file headers
* minor improvement for the routing algorithm
translation_table.{c,h} have been heavily modified by another contributor and
for legal purposes it is better to include his name into the contributor list
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Marek Lindner [Sat, 10 Mar 2012 22:17:53 +0000 (06:17 +0800)]
batman-adv: avoid temporary routing loops by being strict on forwarded OGMs
batman-adv would forward OGMs from non-besthops while replacing the the TQ
and TTL values with the values from the best hop. In certain corner cases
this leads to a temporary routing loop.
This patch changes this behavior: Only packets from best next hops are
forwarded - TQ and TTL values won't be replaced anymore. However, the protocol
needs to rebroadcast OGMs from single hop neighbors regardless of whether or
not they are the best hop. To handle this case a new flag is introduced to
alert neighboring nodes about the forwarded OGM that is not from my best
next hop. It is to be discarded by all nodes except for the one originating
the OGM.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Acked-by: Daniele Furlan <daniele.furlan@gmail.com> Tested-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Linus Luessing [Sat, 10 Mar 2012 22:17:52 +0000 (06:17 +0800)]
batman-adv: Adding hard_iface specific sysfs wrapper macros for UINT
This allows us to easily add a sysfs parameter for an unsigned int
later, which is not for a batman mesh interface (e.g. bat0), but for a
common interface instead. It allows reading and writing an atomic_t in
hard_iface (instead of bat_priv compared to the mesh variant).
Developed by Linus during a 6 months trainee study period in Ascom
(Switzerland) AG.
Signed-off-by: Linus Luessing <linus.luessing@web.de> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Marek Lindner [Sat, 10 Mar 2012 22:17:49 +0000 (06:17 +0800)]
batman-adv: ignore protocol packets if the interface did not enable this protocol
Reported-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Marek Lindner [Thu, 1 Mar 2012 07:35:21 +0000 (15:35 +0800)]
batman-adv: split neigh_new function into generic and batman iv specific parts
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Marek Lindner [Thu, 1 Mar 2012 07:35:20 +0000 (15:35 +0800)]
batman-adv: replace HZ calculations with jiffies_to_msecs()
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Marek Lindner [Thu, 1 Mar 2012 07:35:19 +0000 (15:35 +0800)]
batman-adv: rename last_valid to last_seen
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Marek Lindner [Sun, 4 Mar 2012 08:56:25 +0000 (16:56 +0800)]
batman-adv: register batman ogm receive function during protocol init
The B.A.T.M.A.N. IV OGM receive function still was hard-coded although
it is a routing protocol specific function. This patch takes advantage
of the dynamic packet handler registration to remove the hard-coded
function calls.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Marek Lindner [Thu, 1 Mar 2012 07:35:17 +0000 (15:35 +0800)]
batman-adv: introduce packet type handler array for incoming packets
The packet handler array replaces the growing switch statement, thus
dealing with incoming packets in a more efficient way. It also adds
to possibility to register packet handlers on the fly.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Marek Lindner [Thu, 1 Mar 2012 07:35:16 +0000 (15:35 +0800)]
batman-adv: introduce is_single_hop_neigh variable to increase readability
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
In is_type_dhcprequest(), while parsing a DHCP message, if the entry we found in
the option list is neither a padding nor the dhcp-type, we have to ignore it and
jump as many bytes as its length + 1. The "+ 1" byte is given by the subtype
field itself that has to be jumped too.
Reported-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
According to the RFC4944 (Transmission of IPv6 Packets over
IEEE 802.15.4 Networks), chapter 7:
The IPv6 link-local address [RFC4291] for an IEEE 802.15.4 interface
is formed by appending the Interface Identifier, as defined above, to
the prefix FE80::/64.
projects / mirror_ubuntu-disco-kernel.git / log