Petr Machata [Mon, 6 Jan 2020 18:01:55 +0000 (18:01 +0000)]
mlxsw: spectrum_qdisc: Ignore grafting of invisible FIFO
The following patch will change PRIO to replace a removed Qdisc with an
invisible FIFO, instead of NOOP. mlxsw will see this replacement due to the
graft message that is generated. But because FIFO does not issue its own
REPLACE message, when the graft operation takes place, the Qdisc that mlxsw
tracks under the indicated band is still the old one. The child
handle (0:0) therefore does not match, and mlxsw rejects the graft
operation, which leads to an extack message:
Warning: Offloading graft operation failed.
Fix by ignoring the invisible children in the PRIO graft handler. The
DESTROY message of the removed Qdisc is going to follow shortly and handle
the removal.
Fixes: 32dc5efc6cb4 ("mlxsw: spectrum: qdiscs: prio: Handle graft command") Signed-off-by: Petr Machata <petrm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 6 Jan 2020 14:45:37 +0000 (06:45 -0800)]
gtp: fix bad unlock balance in gtp_encap_enable_socket
WARNING: bad unlock balance detected!
5.5.0-rc5-syzkaller #0 Not tainted
-------------------------------------
syz-executor921/9688 is trying to release lock (sk_lock-AF_INET6) at:
[<ffffffff84bf8506>] gtp_encap_enable_socket+0x146/0x400 drivers/net/gtp.c:830
but there are no more locks to release!
other info that might help us debug this:
2 locks held by syz-executor921/9688:
#0: ffffffff8a4d8840 (rtnl_mutex){+.+.}, at: rtnl_lock net/core/rtnetlink.c:72 [inline]
#0: ffffffff8a4d8840 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x405/0xaf0 net/core/rtnetlink.c:5421
#1: ffff88809304b560 (slock-AF_INET6){+...}, at: spin_lock_bh include/linux/spinlock.h:343 [inline]
#1: ffff88809304b560 (slock-AF_INET6){+...}, at: release_sock+0x20/0x1c0 net/core/sock.c:2951
Chen-Yu Tsai [Mon, 6 Jan 2020 03:09:45 +0000 (11:09 +0800)]
net: stmmac: dwmac-sun8i: Allow all RGMII modes
Allow all the RGMII modes to be used. This would allow us to represent
the hardware better in the device tree with RGMII_ID where in most
cases the PHY's internal delay for both RX and TX are used.
Fixes: 9f93ac8d4085 ("net-next: stmmac: Add dwmac-sun8i") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Chen-Yu Tsai [Mon, 6 Jan 2020 03:09:22 +0000 (11:09 +0800)]
net: stmmac: dwmac-sunxi: Allow all RGMII modes
Allow all the RGMII modes to be used. This would allow us to represent
the hardware better in the device tree with RGMII_ID where in most
cases the PHY's internal delay for both RX and TX are used.
Fixes: af0bd4e9ba80 ("net: stmmac: sunxi platform extensions for GMAC in Allwinner A20 SoC's") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 7 Jan 2020 18:57:01 +0000 (10:57 -0800)]
net: usb: lan78xx: fix possible skb leak
If skb_linearize() fails, we need to free the skb.
TSO makes skb bigger, and this bug might be the reason
Raspberry Pi 3B+ users had to disable TSO.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: RENARD Pierre-Francois <pfrenard@gmail.com> Cc: Stefan Wahren <stefan.wahren@i2se.com> Cc: Woojung Huh <woojung.huh@microchip.com> Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 7 Jan 2020 09:42:25 +0000 (01:42 -0800)]
vlan: vlan_changelink() should propagate errors
Both vlan_dev_change_flags() and vlan_dev_set_egress_priority()
can return an error. vlan_changelink() should not ignore them.
Fixes: 07b5b17e157b ("[VLAN]: Use rtnl_link API") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 7 Jan 2020 09:42:24 +0000 (01:42 -0800)]
vlan: fix memory leak in vlan_dev_set_egress_priority
There are few cases where the ndo_uninit() handler might be not
called if an error happens while device is initialized.
Since vlan_newlink() calls vlan_changelink() before
trying to register the netdevice, we need to make sure
vlan_dev_uninit() has been called at least once,
or we might leak allocated memory.
Fixe: 07b5b17e157b ("[VLAN]: Use rtnl_link API") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiping Ma [Tue, 7 Jan 2020 06:34:00 +0000 (14:34 +0800)]
stmmac: debugfs entry name is not be changed when udev rename device name.
Add one notifier for udev changes net device name. Fixes: b6601323ef9e ("net: stmmac: debugfs entry name is not be changed when udev rename") Signed-off-by: Jiping Ma <jiping.ma2@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Please pull and let me know if there is any problem.
For -stable v5.3
('net/mlx5: Move devlink registration before interfaces load')
For -stable v5.4
('net/mlx5e: Fix hairpin RSS table size')
('net/mlx5: DR, Init lists that are used in rule's member')
('net/mlx5e: Always print health reporter message to dmesg')
('net/mlx5: DR, No need for atomic refcount for internal SW steering resources')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen [Wed, 11 Dec 2019 07:17:40 +0000 (09:17 +0200)]
net/mlx5e: Fix hairpin RSS table size
Set hairpin table size to the corret size, based on the groups that
would be created in it. Groups are laid out on the table such that a
group occupies a range of entries in the table. This implies that the
group ranges should have correspondence to the table they are laid upon.
The patch cited below made group 1's size to grow hence causing
overflow of group range laid on the table.
Fixes: a795d8db2a6d ("net/mlx5e: Support RSS for IP-in-IP and IPv6 tunneled packets") Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
During cleanup path, FTE's parent node group is removed which is
referenced by the FTE while freeing the FTE.
Hence FTE's lockless read lookup optimization done in cited commit is
not possible at the moment.
Hence, revert the commit.
This avoid below KAZAN call trace.
[ 110.390896] BUG: KASAN: use-after-free in find_root.isra.14+0x56/0x60
[mlx5_core]
[ 110.391048] Read of size 4 at addr ffff888c19e6d220 by task
swapper/12/0
Eran Ben Elisha [Wed, 4 Dec 2019 12:34:18 +0000 (14:34 +0200)]
net/mlx5e: Always print health reporter message to dmesg
In case a reporter exists, error message is logged only to the devlink
tracer. The devlink tracer is a visibility utility only, which user can
choose not to monitor.
After cited patch, 3rd party monitoring tools that tracks these error
message will no longer find them in dmesg, causing a regression.
With this patch, error messages are also logged into the dmesg.
Fixes: c50de4af1d63 ("net/mlx5e: Generalize tx reporter's functionality") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Dmytro Linkin [Thu, 31 Oct 2019 16:15:51 +0000 (18:15 +0200)]
net/mlx5e: Avoid duplicating rule destinations
Following scenario easily break driver logic and crash the kernel:
1. Add rule with mirred actions to same device.
2. Delete this rule.
In described scenario rule is not added to database and on deletion
driver access invalid entry.
Example:
$ tc filter add dev ens1f0_0 ingress protocol ip prio 1 \
flower skip_sw \
action mirred egress mirror dev ens1f0_1 pipe \
action mirred egress redirect dev ens1f0_1
$ tc filter del dev ens1f0_0 ingress protocol ip prio 1
After further debugging, turns out while in case of other helper functions
we disallow passing modified ctx, the special case of ld/abs/ind instruction
which has similar semantics (except r6 being the ctx argument) is missing
such check. Modified ctx is impossible here as bpf_skb_load_helper_8_no_cache()
and others are expecting skb fields in original position, hence, add
check_ctx_reg() to reject any modified ctx. Issue was first introduced back
in f1174f77b50c ("bpf/verifier: rework value tracking").
Fixes: f1174f77b50c ("bpf/verifier: rework value tracking") Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/20200106215157.3553-1-daniel@iogearbox.net
Igor Russkikh [Mon, 6 Jan 2020 11:22:30 +0000 (14:22 +0300)]
net: atlantic: remove duplicate entries
Function entries were duplicated accidentally, removing the dups.
Fixes: ea4b4d7fc106 ("net: atlantic: loopback tests via private flags") Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Mon, 6 Jan 2020 11:22:29 +0000 (14:22 +0300)]
net: atlantic: loopback configuration in improper place
Initial loopback configuration should be called earlier, before
starting traffic on HW blocks. Otherwise depending on race conditions
it could be kept disabled.
Fixes: ea4b4d7fc106 ("net: atlantic: loopback tests via private flags") Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Mon, 6 Jan 2020 11:22:28 +0000 (14:22 +0300)]
net: atlantic: broken link status on old fw
Last code/checkpatch cleanup did a copy paste error where code from
firmware 3 API logic was moved to firmware 1 logic.
This resulted in FW1.x users would never see the link state as active.
Fixes: 7b0c342f1f67 ("net: atlantic: code style cleanup") Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roman Gushchin [Fri, 27 Dec 2019 21:50:34 +0000 (13:50 -0800)]
bpf: cgroup: prevent out-of-order release of cgroup bpf
Before commit 4bfc0bb2c60e ("bpf: decouple the lifetime of cgroup_bpf from cgroup itself")
cgroup bpf structures were released with
corresponding cgroup structures. It guaranteed the hierarchical order
of destruction: children were always first. It preserved attached
programs from being released before their propagated copies.
But with cgroup auto-detachment there are no such guarantees anymore:
cgroup bpf is released as soon as the cgroup is offline and there are
no live associated sockets. It means that an attached program can be
detached and released, while its propagated copy is still living
in the cgroup subtree. This will obviously lead to an use-after-free
bug.
To reproduce the issue the following script can be used:
Fix this by grabbing a reference to the bpf structure of each ancestor
on the initialization of the cgroup bpf structure, and dropping the
reference at the end of releasing the cgroup bpf structure.
This will restore the hierarchical order of cgroup bpf releasing,
without adding any operations on hot paths.
Thanks to Josef Bacik for the debugging and the initial analysis of
the problem.
Fixes: 4bfc0bb2c60e ("bpf: decouple the lifetime of cgroup_bpf from cgroup itself") Reported-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Roman Gushchin <guro@fb.com> Acked-by: Song Liu <songliubraving@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Vikas Gupta [Mon, 6 Jan 2020 06:24:02 +0000 (11:54 +0530)]
firmware: tee_bnxt: Fix multiple call to tee_client_close_context
Fix calling multiple tee_client_close_context in case of shm allocation
fails.
Fixes: 246880958ac9 (“firmware: broadcom: add OP-TEE based BNXT f/w manager”) Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 4 Jan 2020 22:14:51 +0000 (23:14 +0100)]
net: dsa: mv88e6xxx: Preserve priority when setting CPU port.
The 6390 family uses an extended register to set the port connected to
the CPU. The lower 5 bits indicate the port, the upper three bits are
the priority of the frames as they pass through the switch, what
egress queue they should use, etc. Since frames being set to the CPU
are typically management frames, BPDU, IGMP, ARP, etc set the priority
to 7, the reset default, and the highest.
Fixes: 33641994a676 ("net: dsa: mv88e6xxx: Monitor and Management tables") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Chris Healy <cphealy@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
name.
"SAMSUNG" is not an abbreviation but a regular trademarked name.
Therefore it should be written with lowercase letters starting with
capital letter.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: wan: sdla: Fix cast from pointer to integer of different size
Since net_device.mem_start is unsigned long, it should not be cast to
int right before casting to pointer. This fixes warning (compile
testing on alpha architecture):
drivers/net/wan/sdla.c: In function ‘sdla_transmit’:
drivers/net/wan/sdla.c:711:13: warning:
cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sat, 4 Jan 2020 06:15:02 +0000 (14:15 +0800)]
sctp: free cmd->obj.chunk for the unprocessed SCTP_CMD_REPLY
This patch is to fix a memleak caused by no place to free cmd->obj.chunk
for the unprocessed SCTP_CMD_REPLY. This issue occurs when failing to
process a cmd while there're still SCTP_CMD_REPLY cmds on the cmd seq
with an allocated chunk in cmd->obj.chunk.
So fix it by freeing cmd->obj.chunk for each SCTP_CMD_REPLY cmd left on
the cmd seq when any cmd returns error. While at it, also remove 'nomem'
label.
Reported-by: syzbot+107c4aff5f392bf1517f@syzkaller.appspotmail.com Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The complaint above occurred because the memory region pointed by attrbuf
variable was not initialized. To eliminate this warning, we use kcalloc()
rather than kmalloc_array() to allocate memory for attrbuf.
Reported-by: syzbot+b1fd2bf2c89d8407e15f@syzkaller.appspotmail.com Signed-off-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Boyd [Sat, 4 Jan 2020 00:19:21 +0000 (16:19 -0800)]
macb: Don't unregister clks unconditionally
The only clk init function in this driver that register a clk is
fu540_c000_clk_init(), and thus we need to unregister the clk when this
driver is removed on that platform. Other init functions, for example
macb_clk_init(), don't register clks and therefore we shouldn't
unregister the clks when this driver is removed. Convert this
registration path to devm so it gets auto-unregistered when this driver
is removed and drop the clk_unregister() calls in driver remove (and
error paths) so that we don't erroneously remove a clk from the system
that isn't registered by this driver.
Otherwise we get strange crashes with a use-after-free when the
devm_clk_get() call in macb_clk_init() calls clk_put() on a clk pointer
that has become invalid because it is freed in clk_unregister().
Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Yash Shah <yash.shah@sifive.com> Reported-by: Guenter Roeck <linux@roeck-us.net> Fixes: c218ad559020 ("macb: Add support for SiFive FU540-C000") Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Carl Huang [Fri, 3 Jan 2020 04:50:16 +0000 (12:50 +0800)]
net: qrtr: fix len of skb_put_padto in qrtr_node_enqueue
The len used for skb_put_padto is wrong, it need to add len of hdr.
In qrtr_node_enqueue, local variable size_t len is assign with
skb->len, then skb_push(skb, sizeof(*hdr)) will add skb->len with
sizeof(*hdr), so local variable size_t len is not same with skb->len
after skb_push(skb, sizeof(*hdr)).
Then the purpose of skb_put_padto(skb, ALIGN(len, 4)) is to add add
pad to the end of the skb's data if skb->len is not aligned to 4, but
unfortunately it use len instead of skb->len, at this line, skb->len
is 32 bytes(sizeof(*hdr)) more than len, for example, len is 3 bytes,
then skb->len is 35 bytes(3 + 32), and ALIGN(len, 4) is 4 bytes, so
__skb_put_padto will do nothing after check size(35) < len(4), the
correct value should be 36(sizeof(*hdr) + ALIGN(len, 4) = 32 + 4),
then __skb_put_padto will pass check size(35) < len(36) and add 1 byte
to the end of skb's data, then logic is correct.
function of skb_push:
void *skb_push(struct sk_buff *skb, unsigned int len)
{
skb->data -= len;
skb->len += len;
if (unlikely(skb->data < skb->head))
skb_under_panic(skb, len, __builtin_return_address(0));
return skb->data;
}
function of skb_put_padto
static inline int skb_put_padto(struct sk_buff *skb, unsigned int len)
{
return __skb_put_padto(skb, len, true);
}
function of __skb_put_padto
static inline int __skb_put_padto(struct sk_buff *skb, unsigned int len,
bool free_on_error)
{
unsigned int size = skb->len;
if (unlikely(size < len)) {
len -= size;
if (__skb_pad(skb, len, free_on_error))
return -ENOMEM;
__skb_put(skb, len);
}
return 0;
}
Signed-off-by: Carl Huang <cjhuang@codeaurora.org> Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Fenghua Yu [Thu, 2 Jan 2020 21:27:06 +0000 (13:27 -0800)]
drivers/net/b44: Change to non-atomic bit operations on pwol_mask
Atomic operations that span cache lines are super-expensive on x86
(not just to the current processor, but also to other processes as all
memory operations are blocked until the operation completes). Upcoming
x86 processors have a switch to cause such operations to generate a #AC
trap. It is expected that some real time systems will enable this mode
in BIOS.
In preparation for this, it is necessary to fix code that may execute
atomic instructions with operands that cross cachelines because the #AC
trap will crash the kernel.
Since "pwol_mask" is local and never exposed to concurrency, there is
no need to set bits in pwol_mask using atomic operations.
Directly operate on the byte which contains the bit instead of using
__set_bit() to avoid any big endian concern due to type cast to
unsigned long in __set_bit().
Suggested-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Liran Alon [Fri, 3 Jan 2020 16:44:59 +0000 (18:44 +0200)]
net: Google gve: Remove dma_wmb() before ringing doorbell
Current code use dma_wmb() to ensure Rx/Tx descriptors are visible
to device before writing to doorbell.
However, these dma_wmb() are wrong and unnecessary. Therefore,
they should be removed.
iowrite32be() called from gve_rx_write_doorbell()/gve_tx_put_doorbell()
should guaratee that all previous writes to WB/UC memory is visible to
device before the write done by iowrite32be().
E.g. On ARM64, iowrite32be() calls __iowmb() which expands to dma_wmb()
and only then calls __raw_writel().
Reviewed-by: Si-Wei Liu <si-wei.liu@oracle.com> Signed-off-by: Liran Alon <liran.alon@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 3 Jan 2020 15:13:56 +0000 (15:13 +0000)]
net: phylink: fix failure to register on x86 systems
The kernel test robot reports a boot failure with qemu in 5.5-rc,
referencing commit 2203cbf2c8b5 ("net: sfp: move fwnode parsing into
sfp-bus layer"). This is caused by phylink_create() being passed a
NULL fwnode, causing fwnode_property_get_reference_args() to return
-EINVAL.
Don't attempt to attach to a SFP bus if we have no fwnode, which
avoids this issue.
Reported-by: kernel test robot <rong.a.chen@intel.com> Fixes: 2203cbf2c8b5 ("net: sfp: move fwnode parsing into sfp-bus layer") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Fri, 3 Jan 2020 07:41:24 +0000 (15:41 +0800)]
selftests: loopback.sh: skip this test if the driver does not support
The loopback feature is only supported on a few drivers like broadcom,
mellanox, etc. The default veth driver has not supported it yet. To avoid
returning failed and making the runner feel confused, let's just skip
the test on drivers that not support loopback.
Fixes: ad11340994d5 ("selftests: Add loopback test") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 3 Jan 2020 00:40:51 +0000 (16:40 -0800)]
Merge tag 'linux-can-fixes-for-5.5-20200102' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2020-01-02
this is a pull request of 9 patches for net/master.
The first 5 patches target all the tcan4x5x driver. The first 3 patches
of them are by Dan Murphy and Sean Nyekjaer and improve the device
initialization (power on, reset and get device out of standby before
register access). The next patch is by Dan Murphy and disables the INH
pin device-state if the GPIO is unavailable. The last patch for the
tcan4x5x driver is by Gustavo A. R. Silva and fixes an inconsistent
PTR_ERR check in the tcan4x5x_parse_config() function.
The next patch is by Oliver Hartkopp and targets the generic CAN device
infrastructure. It ensures that an initialized headroom in outgoing CAN
sk_buffs (e.g. if injected by AF_PACKET).
The last 2 patches are by Johan Hovold and fix the kvaser_usb and gs_usb
drivers by always using the current alternate setting not blindly the
first one.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 2 Jan 2020 14:33:34 +0000 (15:33 +0100)]
net: freescale: fec: Fix ethtool -d runtime PM
In order to dump the FECs registers the clocks have to be ticking,
otherwise a data abort occurs. Add calls to runtime PM so they are
enabled and later disabled.
Fixes: e8fcfcd5684a ("net: fec: optimize the clock management to save power") Reported-by: Chris Healy <Chris.Healy@zii.aero> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Thu, 2 Jan 2020 09:23:45 +0000 (17:23 +0800)]
vxlan: fix tos value before xmit
Before ip_tunnel_ecn_encap() and udp_tunnel_xmit_skb() we should filter
tos value by RT_TOS() instead of using config tos directly.
vxlan_get_route() would filter the tos to fl4.flowi4_tos but we didn't
return it back, as geneve_get_v4_rt() did. So we have to use RT_TOS()
directly in function ip_tunnel_ecn_encap().
Fixes: 206aaafcd279 ("VXLAN: Use IP Tunnels tunnel ENC encap API") Fixes: 1400615d64cf ("vxlan: allow setting ipv6 traffic class") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wen Yang [Thu, 2 Jan 2020 09:21:43 +0000 (17:21 +0800)]
sch_cake: avoid possible divide by zero in cake_enqueue()
The variables 'window_interval' is u64 and do_div()
truncates it to 32 bits, which means it can test
non-zero and be truncated to zero for division.
The unit of window_interval is nanoseconds,
so its lower 32-bit is relatively easy to exceed.
Fix this issue by using div64_u64() instead.
Fixes: 7298de9cd725 ("sch_cake: Add ingress mode") Signed-off-by: Wen Yang <wenyang@linux.alibaba.com> Cc: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Cc: Toke Høiland-Jørgensen <toke@redhat.com> Cc: David S. Miller <davem@davemloft.net> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: cake@lists.bufferbloat.net Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
Pengcheng Yang [Mon, 30 Dec 2019 09:54:41 +0000 (17:54 +0800)]
tcp: fix "old stuff" D-SACK causing SACK to be treated as D-SACK
When we receive a D-SACK, where the sequence number satisfies:
undo_marker <= start_seq < end_seq <= prior_snd_una
we consider this is a valid D-SACK and tcp_is_sackblock_valid()
returns true, then this D-SACK is discarded as "old stuff",
but the variable first_sack_index is not marked as negative
in tcp_sacktag_write_queue().
If this D-SACK also carries a SACK that needs to be processed
(for example, the previous SACK segment was lost), this SACK
will be treated as a D-SACK in the following processing of
tcp_sacktag_write_queue(), which will eventually lead to
incorrect updates of undo_retrans and reordering.
Fixes: fd6dad616d4f ("[TCP]: Earlier SACK block verification & simplify access to them") Signed-off-by: Pengcheng Yang <yangpc@wangsu.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Baruch Siach [Thu, 19 Dec 2019 09:48:22 +0000 (11:48 +0200)]
net: dsa: mv88e6xxx: force cmode write on 6141/6341
mv88e6xxx_port_set_cmode() relies on cmode stored in struct
mv88e6xxx_port to skip cmode update when the requested value matches the
cached value. It turns out that mv88e6xxx_port_hidden_write() might
change the port cmode setting as a side effect, so we can't rely on the
cached value to determine that cmode update in not necessary.
Force cmode update in mv88e6341_port_set_cmode(), to make
serdes configuration work again. Other mv88e6xxx_port_set_cmode()
callers keep the current behaviour.
This fixes serdes configuration of the 6141 switch on SolidRun Clearfog
GT-8K.
Fixes: 7a3007d22e8 ("net: dsa: mv88e6xxx: fully support SERDES on Topaz family") Reported-by: Denis Odintsov <d.odintsov@traviangames.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Faber [Thu, 26 Dec 2019 18:51:24 +0000 (19:51 +0100)]
can: mscan: mscan_rx_poll(): fix rx path lockup when returning from polling to irq mode
Under load, the RX side of the mscan driver can get stuck while TX still
works. Restarting the interface locks up the system. This behaviour
could be reproduced reliably on a MPC5121e based system.
The patch fixes the return value of the NAPI polling function (should be
the number of processed packets, not constant 1) and the condition under
which IRQs are enabled again after polling is finished.
With this patch, no more lockups were observed over a test period of ten
days.
Fixes: afa17a500a36 ("net/can: add driver for mscan family & mpc52xx_mscan") Signed-off-by: Florian Faber <faber@faberman.de> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Johan Hovold [Tue, 10 Dec 2019 11:32:31 +0000 (12:32 +0100)]
can: gs_usb: gs_usb_probe(): use descriptors of current altsetting
Make sure to always use the descriptors of the current alternate setting
to avoid future issues when accessing fields that may differ between
settings.
Signed-off-by: Johan Hovold <johan@kernel.org> Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices") Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Johan Hovold [Tue, 10 Dec 2019 11:32:30 +0000 (12:32 +0100)]
can: kvaser_usb: fix interface sanity check
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: aec5fb2268b7 ("can: kvaser_usb: Add support for Kvaser USB hydra family") Cc: stable <stable@vger.kernel.org> # 4.19 Cc: Jimmy Assarsson <extja@kvaser.com> Cc: Christer Beskow <chbe@kvaser.com> Cc: Nicklas Johansson <extnj@kvaser.com> Cc: Martin Henriksson <mh@kvaser.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oliver Hartkopp [Sat, 7 Dec 2019 18:34:18 +0000 (19:34 +0100)]
can: can_dropped_invalid_skb(): ensure an initialized headroom in outgoing CAN sk_buffs
KMSAN sysbot detected a read access to an untinitialized value in the
headroom of an outgoing CAN related sk_buff. When using CAN sockets this
area is filled appropriately - but when using a packet socket this
initialization is missing.
The problematic read access occurs in the CAN receive path which can
only be triggered when the sk_buff is sent through a (virtual) CAN
interface. So we check in the sending path whether we need to perform
the missing initializations.
Fixes: d3b58c47d330d ("can: replace timestamp as unique skb attribute") Reported-by: syzbot+b02ff0707a97e4e79ebb@syzkaller.appspotmail.com Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Cc: linux-stable <stable@vger.kernel.org> # >= v4.1 Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
can: tcan4x5x: tcan4x5x_parse_config(): fix inconsistent IS_ERR and PTR_ERR
Fix inconsistent IS_ERR and PTR_ERR in tcan4x5x_parse_config().
The proper pointer to be passed as argument is tcan4x5x->device_wake_gpio.
This bug was detected with the help of Coccinelle.
Fixes: 2de497356955 ("can: tcan45x: Make wake-up GPIO an optional GPIO") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Dan Murphy [Tue, 10 Dec 2019 16:32:04 +0000 (10:32 -0600)]
can: tcan4x5x: tcan4x5x_can_probe(): turn on the power before parsing the config
The tcan4x5x_parse_config() function now performs action on the device
either reading or writing and a reset. If the devive has a switchable
power supppy (i.e. regulator is managed) it needs to be turned on.
So turn on the regulator if available. If the parsing fails, turn off
the regulator.
Fixes: 2de497356955 ("can: tcan45x: Make wake-up GPIO an optional GPIO") Signed-off-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the tcan device comes out of reset it goes in standby mode. The
m_can driver tries to access the control register but fails due to the
device being in standby mode.
So this patch will put the tcan device in normal mode before the m_can
driver does the initialization.
Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel") Cc: stable@vger.kernel.org Signed-off-by: Sean Nyekjaer <sean@geanix.com> Acked-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
1) Fix big endian overflow in nf_flow_table, from Arnd Bergmann.
2) Fix port selection on big endian in nft_tproxy, from Phil Sutter.
3) Fix precision tracking for unbound scalars in bpf verifier, from
Daniel Borkmann.
4) Fix integer overflow in socket rcvbuf check in UDP, from Antonio
Messina.
5) Do not perform a neigh confirmation during a pmtu update over a
tunnel, from Hangbin Liu.
6) Fix DMA mapping leak in dpaa_eth driver, from Madalin Bucur.
7) Various PTP fixes for sja1105 dsa driver, from Vladimir Oltean.
8) Add missing to dummy definition of of_mdiobus_child_is_phy(), from
Geert Uytterhoeven
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (54 commits)
hsr: fix slab-out-of-bounds Read in hsr_debugfs_rename()
net/sched: add delete_empty() to filters and use it in cls_flower
tcp: Fix highest_sack and highest_sack_seq
ptp: fix the race between the release of ptp_clock and cdev
net: dsa: sja1105: Reconcile the meaning of TPID and TPID2 for E/T and P/Q/R/S
Documentation: net: dsa: sja1105: Remove text about taprio base-time limitation
net: dsa: sja1105: Remove restriction of zero base-time for taprio offload
net: dsa: sja1105: Really make the PTP command read-write
net: dsa: sja1105: Take PTP egress timestamp by port, not mgmt slot
cxgb4/cxgb4vf: fix flow control display for auto negotiation
mlxsw: spectrum: Use dedicated policer for VRRP packets
mlxsw: spectrum_router: Skip loopback RIFs during MAC validation
net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs
net/sched: act_mirred: Pull mac prior redir to non mac_header_xmit device
net_sched: sch_fq: properly set sk->sk_pacing_status
bnx2x: Fix accounting of vlan resources among the PFs
bnx2x: Use appropriate define for vlan credit
of: mdio: Add missing inline to of_mdiobus_child_is_phy() dummy
net: phy: aquantia: add suspend / resume ops for AQR105
dpaa_eth: fix DMA mapping leak
...
Linus Torvalds [Tue, 31 Dec 2019 18:51:27 +0000 (10:51 -0800)]
Merge tag 'tomoyo-fixes-for-5.5' of git://git.osdn.net/gitroot/tomoyo/tomoyo-test1
Pull tomoyo fixes from Tetsuo Handa:
"Two bug fixes:
- Suppress RCU warning at list_for_each_entry_rcu()
- Don't use fancy names on sockets"
* tag 'tomoyo-fixes-for-5.5' of git://git.osdn.net/gitroot/tomoyo/tomoyo-test1:
tomoyo: Suppress RCU warning at list_for_each_entry_rcu().
tomoyo: Don't use nifty names on sockets.
Taehee Yoo [Sat, 28 Dec 2019 16:28:09 +0000 (16:28 +0000)]
hsr: fix slab-out-of-bounds Read in hsr_debugfs_rename()
hsr slave interfaces don't have debugfs directory.
So, hsr_debugfs_rename() shouldn't be called when hsr slave interface name
is changed.
Test commands:
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1
ip link set dummy0 name ap
Reported-by: syzbot+9328206518f08318a5fd@syzkaller.appspotmail.com Fixes: 4c2d5e33dcd3 ("hsr: rename debugfs file when interface name is changed") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Sat, 28 Dec 2019 15:36:58 +0000 (16:36 +0100)]
net/sched: add delete_empty() to filters and use it in cls_flower
Revert "net/sched: cls_u32: fix refcount leak in the error path of
u32_change()", and fix the u32 refcount leak in a more generic way that
preserves the semantic of rule dumping.
On tc filters that don't support lockless insertion/removal, there is no
need to guard against concurrent insertion when a removal is in progress.
Therefore, for most of them we can avoid a full walk() when deleting, and
just decrease the refcount, like it was done on older Linux kernels.
This fixes situations where walk() was wrongly detecting a non-empty
filter, like it happened with cls_u32 in the error path of change(), thus
leading to failures in the following tdc selftests:
6aa7: (filter, u32) Add/Replace u32 with source match and invalid indev
6658: (filter, u32) Add/Replace u32 with custom hash table and invalid handle
74c2: (filter, u32) Add/Replace u32 filter with invalid hash table id
On cls_flower, and on (future) lockless filters, this check is necessary:
move all the check_empty() logic in a callback so that each filter
can have its own implementation. For cls_flower, it's sufficient to check
if no IDRs have been allocated.
Changes since v1:
- document the need for delete_empty() when TCF_PROTO_OPS_DOIT_UNLOCKED
is used, thanks to Vlad Buslov
- implement delete_empty() without doing fl_walk(), thanks to Vlad Buslov
- squash revert and new fix in a single patch, to be nice with bisect
tests that run tdc on u32 filter, thanks to Dave Miller
Fixes: 275c44aa194b ("net/sched: cls_u32: fix refcount leak in the error path of u32_change()") Fixes: 6676d5e416ee ("net: sched: set dedicated tcf_walker flag when tp is empty") Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com> Suggested-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Reviewed-by: Vlad Buslov <vladbu@mellanox.com> Tested-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cambda Zhu [Fri, 27 Dec 2019 08:52:37 +0000 (16:52 +0800)]
tcp: Fix highest_sack and highest_sack_seq
>From commit 50895b9de1d3 ("tcp: highest_sack fix"), the logic about
setting tp->highest_sack to the head of the send queue was removed.
Of course the logic is error prone, but it is logical. Before we
remove the pointer to the highest sack skb and use the seq instead,
we need to set tp->highest_sack to NULL when there is no skb after
the last sack, and then replace NULL with the real skb when new skb
inserted into the rtx queue, because the NULL means the highest sack
seq is tp->snd_nxt. If tp->highest_sack is NULL and new data sent,
the next ACK with sack option will increase tp->reordering unexpectedly.
This patch sets tp->highest_sack to the tail of the rtx queue if
it's NULL and new data is sent. The patch keeps the rule that the
highest_sack can only be maintained by sack processing, except for
this only case.
Fixes: 50895b9de1d3 ("tcp: highest_sack fix") Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladis Dronov [Fri, 27 Dec 2019 02:26:27 +0000 (03:26 +0100)]
ptp: fix the race between the release of ptp_clock and cdev
In a case when a ptp chardev (like /dev/ptp0) is open but an underlying
device is removed, closing this file leads to a race. This reproduces
easily in a kvm virtual machine:
static void __fput(struct file *file)
{ ...
if (file->f_op->release)
file->f_op->release(inode, file); <<< cdev is kfree'd here
if (unlikely(S_ISCHR(inode->i_mode) && inode->i_cdev != NULL &&
!(mode & FMODE_PATH))) {
cdev_put(inode->i_cdev); <<< cdev fields are accessed here
Namely:
__fput()
posix_clock_release()
kref_put(&clk->kref, delete_clock) <<< the last reference
delete_clock()
delete_ptp_clock()
kfree(ptp) <<< cdev is embedded in ptp
cdev_put
module_put(p->owner) <<< *p is kfree'd, bang!
Here cdev is embedded in posix_clock which is embedded in ptp_clock.
The race happens because ptp_clock's lifetime is controlled by two
refcounts: kref and cdev.kobj in posix_clock. This is wrong.
Make ptp_clock's sysfs device a parent of cdev with cdev_device_add()
created especially for such cases. This way the parent device with its
ptp_clock is not released until all references to the cdev are released.
This adds a requirement that an initialized but not exposed struct
device should be provided to posix_clock_register() by a caller instead
of a simple dev_t.
This approach was adopted from the commit 72139dfa2464 ("watchdog: Fix
the race between the release of watchdog_core_data and cdev"). See
details of the implementation in the commit 233ed09d7fda ("chardev: add
helper function to register char devs with a struct device").
Link: https://lore.kernel.org/linux-fsdevel/20191125125342.6189-1-vdronov@redhat.com/T/#u Analyzed-by: Stephen Johnston <sjohnsto@redhat.com> Analyzed-by: Vern Lovejoy <vlovejoy@redhat.com> Signed-off-by: Vladis Dronov <vdronov@redhat.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Dec 2019 01:11:13 +0000 (03:11 +0200)]
net: dsa: sja1105: Reconcile the meaning of TPID and TPID2 for E/T and P/Q/R/S
For first-generation switches (SJA1105E and SJA1105T):
- TPID means C-Tag (typically 0x8100)
- TPID2 means S-Tag (typically 0x88A8)
While for the second generation switches (SJA1105P, SJA1105Q, SJA1105R,
SJA1105S) it is the other way around:
- TPID means S-Tag (typically 0x88A8)
- TPID2 means C-Tag (typically 0x8100)
In other words, E/T tags untagged traffic with TPID, and P/Q/R/S with
TPID2.
So the patch mentioned below fixed VLAN filtering for P/Q/R/S, but broke
it for E/T.
We strive for a common code path for all switches in the family, so just
lie in the static config packing functions that TPID and TPID2 are at
swapped bit offsets than they actually are, for P/Q/R/S. This will make
both switches understand TPID to be ETH_P_8021Q and TPID2 to be
ETH_P_8021AD. The meaning from the original E/T was chosen over P/Q/R/S
because E/T is actually the one with public documentation available
(UM10944.pdf).
Fixes: f9a1a7646c0d ("net: dsa: sja1105: Reverse TPID and TPID2") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Dec 2019 01:08:07 +0000 (03:08 +0200)]
Documentation: net: dsa: sja1105: Remove text about taprio base-time limitation
Since commit 86db36a347b4 ("net: dsa: sja1105: Implement state machine
for TAS with PTP clock source"), this paragraph is no longer true. So
remove it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Dec 2019 01:03:54 +0000 (03:03 +0200)]
net: dsa: sja1105: Remove restriction of zero base-time for taprio offload
The check originates from the initial implementation which was not based
on PTP time but on a standalone clock source. In the meantime we can now
program the PTPSCHTM register at runtime with the dynamic base time
(actually with a value that is 200 ns smaller, to avoid writing DELTA=0
in the Schedule Entry Points Parameters Table). And we also have logic
for moving the actual base time in the future of the PHC's current time
base, so the check for zero serves no purpose, since even if the user
will specify zero, that's not what will end up in the static config
table where the limitation is.
Fixes: 86db36a347b4 ("net: dsa: sja1105: Implement state machine for TAS with PTP clock source") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Dec 2019 01:01:50 +0000 (03:01 +0200)]
net: dsa: sja1105: Really make the PTP command read-write
When activating tc-taprio offload on the switch ports, the TAS state
machine will try to check whether it is running or not, but will find
both the STARTED and STOPPED bits as false in the
sja1105_tas_check_running function. So the function will return -EINVAL
(an abnormal situation) and the kernel will keep printing this from the
TAS FSM workqueue:
[ 37.691971] sja1105 spi0.1: An operation returned -22
The reason is that the underlying function that gets called,
sja1105_ptp_commit, does not actually do a SPI_READ, but a SPI_WRITE. So
the command buffer remains initialized with zeroes instead of retrieving
the hardware state. Fix that.
Fixes: 41603d78b362 ("net: dsa: sja1105: Make the PTP command read-write") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Dec 2019 00:59:54 +0000 (02:59 +0200)]
net: dsa: sja1105: Take PTP egress timestamp by port, not mgmt slot
The PTP egress timestamp N must be captured from register PTPEGR_TS[n],
where n = 2 * PORT + TSREG. There are 10 PTPEGR_TS registers, 2 per
port. We are only using TSREG=0.
As opposed to the management slots, which are 4 in number
(SJA1105_NUM_PORTS, minus the CPU port). Any management frame (which
includes PTP frames) can be sent to any non-CPU port through any
management slot. When the CPU port is not the last port (#4), there will
be a mismatch between the slot and the port number.
Luckily, the only mainline occurrence with this switch
(arch/arm/boot/dts/ls1021a-tsn.dts) does have the CPU port as #4, so the
issue did not manifest itself thus far.
Fixes: 47ed985e97f5 ("net: dsa: sja1105: Add logic for TX timestamping") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rahul Lakkireddy [Mon, 30 Dec 2019 12:44:08 +0000 (18:14 +0530)]
cxgb4/cxgb4vf: fix flow control display for auto negotiation
As per 802.3-2005, Section Two, Annex 28B, Table 28B-2 [1], when
_only_ Rx pause is enabled, both symmetric and asymmetric pause
towards local device must be enabled. Also, firmware returns the local
device's flow control pause params as part of advertised capabilities
and negotiated params as part of current link attributes. So, fix up
ethtool's flow control pause params fetch logic to read from acaps,
instead of linkattr.
David S. Miller [Sun, 29 Dec 2019 20:29:14 +0000 (12:29 -0800)]
Merge branch 'mlxsw-fixes'
Ido Schimmel says:
====================
mlxsw: Couple of fixes
This patch set contains two fixes for mlxsw. Please consider both for
stable.
Patch #1 from Amit fixes a wrong check during MAC validation when
creating router interfaces (RIFs). Given a particular order of
configuration this can result in the driver refusing to create new RIFs.
Patch #2 fixes a wrong trap configuration in which VRRP packets and
routing exceptions were policed by the same policer towards the CPU. In
certain situations this can prevent VRRP packets from reaching the CPU.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sun, 29 Dec 2019 11:40:23 +0000 (13:40 +0200)]
mlxsw: spectrum: Use dedicated policer for VRRP packets
Currently, VRRP packets and packets that hit exceptions during routing
(e.g., MTU error) are policed using the same policer towards the CPU.
This means, for example, that misconfiguration of the MTU on a routed
interface can prevent VRRP packets from reaching the CPU, which in turn
can cause the VRRP daemon to assume it is the Master router.
Fix this by using a dedicated policer for VRRP packets.
Fixes: 11566d34f895 ("mlxsw: spectrum: Add VRRP traps") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Alex Veber <alexve@mellanox.com> Tested-by: Alex Veber <alexve@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Sun, 29 Dec 2019 11:40:22 +0000 (13:40 +0200)]
mlxsw: spectrum_router: Skip loopback RIFs during MAC validation
When a router interface (RIF) is created the MAC address of the backing
netdev is verified to have the same MSBs as existing RIFs. This is
required in order to avoid changing existing RIF MAC addresses that all
share the same MSBs.
Loopback RIFs are special in this regard as they do not have a MAC
address, given they are only used to loop packets from the overlay to
the underlay.
Without this change, an error is returned when trying to create a RIF
after the creation of a GRE tunnel that is represented by a loopback
RIF. 'rif->dev->dev_addr' points to the GRE device's local IP, which
does not share the same MSBs as physical interfaces. Adding an IP
address to any physical interface results in:
Error: mlxsw_spectrum: All router interface MAC addresses must have the
same prefix.
Fix this by skipping loopback RIFs during MAC validation.
Fixes: 74bc99397438 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses") Signed-off-by: Amit Cohen <amitc@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 29 Dec 2019 18:01:27 +0000 (10:01 -0800)]
Merge tag 'riscv/for-v5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"One important fix for RISC-V:
- Redirect any incoming syscall with an ID less than -1 to
sys_ni_syscall, rather than allowing them to fall through into the
syscall handler.
and two minor build fixes:
- Export __asm_copy_{from,to}_user() from where they are defined.
This fixes a build error triggered by some randconfigs.
- Export flush_icache_all(). I'd resisted this before, since
historically we didn't want modules to be able to flush the I$
directly; but apparently everyone else is doing it now"
* tag 'riscv/for-v5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: export flush_icache_all to modules
riscv: reject invalid syscalls below -1
riscv: fix compile failure with EXPORT_SYMBOL() & !MMU
Linus Torvalds [Sun, 29 Dec 2019 17:50:57 +0000 (09:50 -0800)]
Merge tag 'locks-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux
Pull /proc/locks formatting fix from Jeff Layton:
"This is a trivial fix for a _very_ long standing bug in /proc/locks
formatting. Ordinarily, I'd wait for the merge window for something
like this, but it is making it difficult to validate some overlayfs
fixes.
I've also gone ahead and marked this for stable"
* tag 'locks-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
locks: print unsigned ino in /proc/locks
Linus Torvalds [Sun, 29 Dec 2019 17:48:47 +0000 (09:48 -0800)]
Merge tag '5.5-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"One performance fix for large directory searches, and one minor style
cleanup noticed by Clang"
* tag '5.5-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Optimize readdir on reparse points
cifs: Adjust indentation in smb2_open_file
Olof Johansson [Tue, 17 Dec 2019 04:07:04 +0000 (20:07 -0800)]
riscv: export flush_icache_all to modules
This is needed by LKDTM (crash dump test module), it calls
flush_icache_range(), which on RISC-V turns into flush_icache_all(). On
other architectures, the actual implementation is exported, so follow
that precedence and export it here too.
Fixes build of CONFIG_LKDTM that fails with:
ERROR: "flush_icache_all" [drivers/misc/lkdtm/lkdtm.ko] undefined!
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Running "stress-ng --enosys 4 -t 20 -v" showed a large number of kernel oops
with "Unable to handle kernel paging request at virtual address" message. This
happens when enosys stressor starts testing random non-valid syscalls.
I forgot to redirect any syscall below -1 to sys_ni_syscall.
With the patch kernel oops messages are gone while running stress-ng enosys
stressor.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com> Fixes: 5340627e3fe0 ("riscv: add support for SECCOMP and SECCOMP_FILTER") Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
riscv: fix compile failure with EXPORT_SYMBOL() & !MMU
When support for !MMU was added, the declaration of
__asm_copy_to_user() & __asm_copy_from_user() were #ifdefed
out hence their EXPORT_SYMBOL() give an error message like:
.../riscv_ksyms.c:13:15: error: '__asm_copy_to_user' undeclared here
.../riscv_ksyms.c:14:15: error: '__asm_copy_from_user' undeclared here
Since these symbols are not defined with !MMU it's wrong to export them.
Same for __clear_user() (even though this one is also declared in
include/asm-generic/uaccess.h and thus doesn't give an error message).
Fix this by doing the EXPORT_SYMBOL() directly where these symbols
are defined: inside lib/uaccess.S itself.
Fixes: 6bd33e1ece52 ("riscv: fix compile failure with EXPORT_SYMBOL() & !MMU") Reported-by: kbuild test robot <lkp@intel.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs
GXBB and newer SoCs use the fixed FCLK_DIV2 (1GHz) clock as input for
the m250_sel clock. Meson8b and Meson8m2 use MPLL2 instead, whose rate
can be adjusted at runtime.
So far we have been running MPLL2 with ~250MHz (and the internal
m250_div with value 1), which worked enough that we could transfer data
with an TX delay of 4ns. Unfortunately there is high packet loss with
an RGMII PHY when transferring data (receiving data works fine though).
Odroid-C1's u-boot is running with a TX delay of only 2ns as well as
the internal m250_div set to 2 - no lost (TX) packets can be observed
with that setting in u-boot.
Manual testing has shown that the TX packet loss goes away when using
the following settings in Linux (the vendor kernel uses the same
settings):
- MPLL2 clock set to ~500MHz
- m250_div set to 2
- TX delay set to 2ns on the MAC side
Update the m250_div divider settings to only accept dividers greater or
equal 2 to fix the TX delay generated by the MAC.
iperf3 results before the change:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 182 MBytes 153 Mbits/sec 514 sender
[ 5] 0.00-10.00 sec 182 MBytes 152 Mbits/sec receiver
iperf3 results after the change (including an updated TX delay of 2ns):
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-10.00 sec 927 MBytes 778 Mbits/sec 0 sender
[ 5] 0.00-10.01 sec 927 MBytes 777 Mbits/sec receiver
Fixes: 4f6a71b84e1afd ("net: stmmac: dwmac-meson8b: fix internal RGMII clock configuration") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Shmulik Ladkani [Wed, 25 Dec 2019 08:51:01 +0000 (10:51 +0200)]
net/sched: act_mirred: Pull mac prior redir to non mac_header_xmit device
There's no skb_pull performed when a mirred action is set at egress of a
mac device, with a target device/action that expects skb->data to point
at the network header.
As a result, either the target device is errornously given an skb with
data pointing to the mac (egress case), or the net stack receives the
skb with data pointing to the mac (ingress case).
E.g:
# tc qdisc add dev eth9 root handle 1: prio
# tc filter add dev eth9 parent 1: prio 9 protocol ip handle 9 basic \
action mirred egress redirect dev tun0
(tun0 is a tun device. result: tun0 errornously gets the eth header
instead of the iph)
Revise the push/pull logic of tcf_mirred_act() to not rely on the
skb_at_tc_ingress() vs tcf_mirred_act_wants_ingress() comparison, as it
does not cover all "pull" cases.
Instead, calculate whether the required action on the target device
requires the data to point at the network header, and compare this to
whether skb->data points to network header - and make the push/pull
adjustments as necessary.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Shmulik Ladkani <sladkani@proofpoint.com> Tested-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 27 Dec 2019 21:21:06 +0000 (13:21 -0800)]
Merge tag 'drm-fixes-2019-12-28' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Post-xmas food coma recovery fixes. Only three fixes for i915 since I
expect most people are holidaying.
i915:
- power management rc6 fix
- framebuffer tracking fix
- display power management ratelimit fix"
* tag 'drm-fixes-2019-12-28' of git://anongit.freedesktop.org/drm/drm:
drm/i915: Hold reference to intel_frontbuffer as we track activity
drm/i915/gt: Ratelimit display power w/a
drm/i915/pmu: Ensure monotonic rc6
Linus Torvalds [Fri, 27 Dec 2019 19:30:26 +0000 (11:30 -0800)]
Merge tag 'linux-kselftest-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
- rseq build failures fixes related to glibc 2.30 compatibility from
Mathieu Desnoyers
- Kunit fixes and cleanups from SeongJae Park
- Fixes to filesystems/epoll, firmware, and livepatch build failures
and skip handling.
* tag 'linux-kselftest-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
rseq/selftests: Clarify rseq_prepare_unload() helper requirements
rseq/selftests: Fix: Namespace gettid() for compatibility with glibc 2.30
rseq/selftests: Turn off timeout setting
kunit/kunit_tool_test: Test '--build_dir' option run
kunit: Rename 'kunitconfig' to '.kunitconfig'
kunit: Place 'test.log' under the 'build_dir'
kunit: Create default config in '--build_dir'
kunit: Remove duplicated defconfig creation
docs/kunit/start: Use in-tree 'kunit_defconfig'
selftests: livepatch: Fix it to do root uid check and skip
selftests: firmware: Fix it to do root uid check and skip
selftests: filesystems/epoll: fix build error
Linus Torvalds [Fri, 27 Dec 2019 19:26:54 +0000 (11:26 -0800)]
Merge tag 'pm-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Fix compile test of the Tegra devfreq driver (Arnd Bergmann) and
remove redundant Kconfig dependencies from multiple devfreq drivers
(Leonard Crestez)"
* tag 'pm-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / devfreq: tegra: Add COMMON_CLK dependency
PM / devfreq: Drop explicit selection of PM_OPP
Linus Torvalds [Fri, 27 Dec 2019 19:17:08 +0000 (11:17 -0800)]
Merge tag 'io_uring-5.5-20191226' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
- Removal of now unused busy wqe list (Hillf)
- Add cond_resched() to io-wq work processing (Hillf)
- And then the series that I hinted at from last week, which removes
the sqe from the io_kiocb and keeps all sqe handling on the prep
side. This guarantees that an opcode can't do the wrong thing and
read the sqe more than once. This is unchanged from last week, no
issues have been observed with this in testing. Hence I really think
we should fold this into 5.5.
* tag 'io_uring-5.5-20191226' of git://git.kernel.dk/linux-block:
io-wq: add cond_resched() to worker thread
io-wq: remove unused busy list from io_sqe
io_uring: pass in 'sqe' to the prep handlers
io_uring: standardize the prep methods
io_uring: read 'count' for IORING_OP_TIMEOUT in prep handler
io_uring: move all prep state for IORING_OP_{SEND,RECV}_MGS to prep handler
io_uring: move all prep state for IORING_OP_CONNECT to prep handler
io_uring: add and use struct io_rw for read/writes
io_uring: use u64_to_user_ptr() consistently
Linus Torvalds [Fri, 27 Dec 2019 19:09:04 +0000 (11:09 -0800)]
Merge tag 'block-5.5-20191226' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Only thing here are the changes from Arnd from last week, which now
have the appropriate header include to ensure they actually compile if
COMPAT is enabled"
* tag 'block-5.5-20191226' of git://git.kernel.dk/linux-block:
compat_ioctl: block: handle Persistent Reservations
compat_ioctl: block: handle add zone open, close and finish ioctl
compat_ioctl: block: handle BLKGETZONESZ/BLKGETNRZONES
compat_ioctl: block: handle BLKREPORTZONE/BLKRESETZONE
pktcdvd: fix regression on 64-bit architectures
Linus Torvalds [Fri, 27 Dec 2019 19:02:48 +0000 (11:02 -0800)]
Merge tag 'gpio-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"A set of fixes for the v5.5 series:
- Fix the build for the Xtensa driver.
- Make sure to set up the parent device for mpc8xxx.
- Clarify the look-up error message.
- Fix the usage of the line direction in the mockup device.
- Fix a type warning on the Aspeed driver.
- Remove the pointless __exit annotation on the xgs-iproc which is
causing a compilation problem.
- Fix up emultation of open drain outputs .get_direction()
- Fix the IRQ callbacks on the PCA953xx to use bitops and work
properly.
- Fix the Kconfig on the Tegra driver"
* tag 'gpio-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tegra186: Allow building on Tegra194-only configurations
gpio: pca953x: Switch to bitops in IRQ callbacks
gpiolib: fix up emulated open drain outputs
MAINTAINERS: Append missed file to the database
gpio: xgs-iproc: remove __exit annotation for iproc_gpio_remove
gpio: aspeed: avoid return type warning
gpio: mockup: Fix usage of new GPIO_LINE_DIRECTION
gpio: Fix error message on out-of-range GPIO in lookup table
gpio: mpc8xxx: Add platform device to gpiochip->parent
gpio: xtensa: fix driver build
Eric Dumazet [Mon, 23 Dec 2019 19:13:24 +0000 (11:13 -0800)]
net_sched: sch_fq: properly set sk->sk_pacing_status
If fq_classify() recycles a struct fq_flow because
a socket structure has been reallocated, we do not
set sk->sk_pacing_status immediately, but later if the
flow becomes detached.
This means that any flow requiring pacing (BBR, or SO_MAX_PACING_RATE)
might fallback to TCP internal pacing, which requires a per-socket
high resolution timer, and therefore more cpu cycles.
Fixes: 218af599fa63 ("tcp: internal implementation for pacing") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Soheil Hassas Yeganeh <soheil@google.com> Cc: Neal Cardwell <ncardwell@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 26 Dec 2019 23:27:15 +0000 (15:27 -0800)]
Merge branch 'bnx2x-Bug-fixes'
Manish Chopra says:
====================
bnx2x: Bug fixes
This series has changes in the area of vlan resources
management APIs to fix fw assert issue reported in max
vlan configuration testing over the PF.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Mon, 23 Dec 2019 18:23:09 +0000 (10:23 -0800)]
bnx2x: Fix accounting of vlan resources among the PFs
While testing max vlan configuration on the PF, firmware gets
assert as driver was configuring number of vlans more than what
is supported per port/engine, it was figured out that there is an
implicit vlan (hidden default vlan consuming hardware cam entry resource)
which is configured default for all the clients (PF/VFs) on client_init
ramrod by the adapter implicitly, so when allocating resources among the
PFs this implicit vlan should be considered or total vlan entries should
be reduced by one to accommodate that default/implicit vlan entry.
Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Mon, 23 Dec 2019 18:23:08 +0000 (10:23 -0800)]
bnx2x: Use appropriate define for vlan credit
Although it has same value as MAX_MAC_CREDIT_E2,
use MAX_VLAN_CREDIT_E2 appropriately.
Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
of: mdio: Add missing inline to of_mdiobus_child_is_phy() dummy
If CONFIG_OF_MDIO=n:
drivers/net/phy/mdio_bus.c:23:
include/linux/of_mdio.h:58:13: warning: ‘of_mdiobus_child_is_phy’ defined but not used [-Wunused-function]
static bool of_mdiobus_child_is_phy(struct device_node *child)
^~~~~~~~~~~~~~~~~~~~~~~
Fix this by adding the missing "inline" keyword.
Fixes: 0aa4d016c043d16a ("of: mdio: export of_mdiobus_child_is_phy") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Borislav Petkov <bp@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>