gpio: add flags argument to gpiod_get*() functions
The huge majority of GPIOs have their direction and initial value set
right after being obtained by one of the gpiod_get() functions. The
integer GPIO API had gpio_request_one() that took a convenience flags
parameter allowing to specify an direction and value applied to the
returned GPIO. This feature greatly simplifies client code and ensures
errors are always handled properly.
A similar feature has been requested for the gpiod API. Since setting
the direction of a GPIO is so often the very next action done after
obtaining its descriptor, we prefer to extend the existing functions
instead of introducing new functions that would raise the
number of gpiod getters to 16 (!).
The drawback of this approach is that all gpiod clients need to be
updated. To limit the pain, temporary macros are introduced that allow
gpiod_get*() to be called with or without the extra flags argument. They
will be removed once all consumer code has been updated.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since now we have irqchip helpers that the GPIO chip drivers are supposed
to use if possible, we can move the registration of ACPI events to happen
in these helpers. This seems to be more natural place and might encourage
GPIO chip driver writers to take advantage of the irqchip helpers.
We make the functions available to GPIO chip drivers via private gpiolib.h,
just in case generic irqchip helpers are not suitable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio: split gpiod board registration into machine header
As per example from the regulator subsystem: put all defines and
functions related to registering board info for GPIO descriptors
into a separate <linux/gpio/machine.h> header.
Cc: Andrew Victor <linux@maxim.org.za> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Thierry Reding <thierry.reding@gmail.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Alexandre Courbot <gnurou@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio_ensure_requested() has been introduced in Feb. 2008 by commit d2876d08d86f2 to force users of the GPIO API to explicitly request GPIOs
before using them.
Hopefully by now all GPIOs are correctly requested and this extra check
can be omitted ; in any case the GPIO maintainers won't feel bad if
machines start failing after 6 years of warnings.
This patch removes that function from the dark ages.
gpiolib: Export gpiochip_request_own_desc and gpiochip_free_own_desc
Both functions were introduced to let gpio drivers request their own
gpio pins. Without exporting the functions, this can however only be
used by gpio drivers built into the kernel.
Secondary impact is that the functions can not currently be used by
platform initialization code associated with the gpio-pca953x driver.
This code permits auto-export of gpio pins through platform data, but
if this functionality is used, the module can no longer be unloaded due
to the problem solved with the introduction of gpiochip_request_own_desc
and gpiochip_free_own_desc.
Export both function so they can be used from modules and from
platform initialization code.
gpio: move gpio_ensure_requested() into legacy C file
gpio_ensure_requested() only makes sense when using the integer-based
GPIO API, so make sure it is called from there instead of the gpiod
API which we know cannot be called with a non-requested GPIO anyway.
The uses of gpio_ensure_requested() in the gpiod API were kind of
out-of-place anyway, so putting them in gpio-legacy.c helps clearing the
code.
Actually, considering the time this ensure_requested mechanism has been
around, maybe we should just turn this patch into "remove
gpio_ensure_requested()" if we know for sure that no user depend on it
anymore?
gpio_lock/unlock_as_irq() are working with (chip, offset) arguments and
are thus not using the old integer namespace. Therefore, there is no
reason to have gpiod variants of these functions working with
descriptors, especially since the (chip, offset) tuple is more suitable
to the users of these functions (GPIO drivers, whereas GPIO descriptors
are targeted at GPIO consumers).
As GPIO descriptors are not going to remain unique anymore, having this
function public is not safe. Restrain its use to gpiolib since we have
no user outside of it.
For some reason gpiochip_export() would invalidate all the descriptors
of a chip if exporting it to sysfs failed. This does not appear as
necessary. Remove that part of the code.
While we are at it, add a note about the non-safety of temporarily
releasing a spinlock in the middle of the loop that protects its
iterator, and explain why this is done.
gpio: Add support for GPIOF_ACTIVE_LOW to gpio_request_one functions
The gpio include file and the gpio documentation declare and document
GPIOF_ACTIVE_LOW as one of the flags to be passed to gpio_request_one
and related functions. However, the flag is not evaluated or used.
This can cause problems in at least two areas: First, the same API can
be used to auto-export pins to user space. The missing support for
GPIOF_ACTIVE_LOW results in unexpected behavior for such auto-exported
pins. Second, the requested gpio pin can be convered for use by
gpiod functions with gpio_to_desc(). While gpio API functions do not
support GPIOF_ACTIVE_LOW, gpiod functions do, which again results in
unexpected behavior.
Check the flag in gpio_request_one and set the gpio internal flag
FLAG_ACTIVE_LOW if it is set to address those problems.
gpio: zynq: Clear pending interrupt when enabling a IRQ
The Zynq GPIO controller does not disable the interrupt detection when the
interrupt is masked and only disables the propagation of the interrupt. This
means when the controller detects an interrupt condition while the interrupt is
logically disabled (and masked) it will propagate the recorded interrupt event
once the interrupt is enabled. This will cause the interrupt consumer to see
spurious interrupts to prevent this first make sure that the interrupt is not
asserted and then enable it.
E.g. when a interrupt is requested with request_irq() it will be configured
according to the requested type (edge/level triggered, etc.) after that it will
be enabled. But the detection circuit might have already registered a false
interrupt before the interrupt type was correctly configured and once the
interrupt is unmasked this false interrupt will be propagated and the interrupt
handler for the just request interrupt will called.
gpio: drop retval check enforcing from gpiochip_remove()
As we start to decomission the return value from gpiochip_remove()
the compilers emit warnings due to the function being tagged
__must_check. So drop this until we remove the return value
altogether.
Add support for GPIO controller used by Xilinx Zynq.
v3 changes:
- Use linux/gpio/driver.h instead of linux/gpio.h
- Make irq a local variable in probe
v2 changes:
- convert to pm_runtime_force_(suspend|resume)
- add pm_runtime_set_active in probe()
- also (un)prepare clocks when they are dis-/enabled
- add some missing calls to pm_runtime_get()
- use pm_runtime_put() instead of sync variant
- remove gpio chip in driver remove()
- remove redundant type casts
- directly use IO helpers
- use BIT macro to set/clear bits
- migrate to GPIOLIB_IRQCHIP
The old integer GPIO interface is, in effect, a privileged user of the
gpiod interface. Reflect this fact further by moving legacy GPIO support
into its own source file. This makes the code clearer and will allow us
to disable legacy GPIO support in the (far) future.
sysfs support is currently entangled within the core GPIO support, while
it should relly just be a (privileged) user of the integer GPIO API.
This patch is a first step towards making the gpiolib code more readable
by splitting it into logical parts.
Move all sysfs support to their own source file, and share static
members of gpiolib that need to be in the private gpiolib.h file. In
the future we will want to put some of them back into gpiolib.c, but this
first patch let us at least identify them.
Compiling out GPIO labels results in a space gain so small that it can
hardly be justified. Labels can also be useful for printing debug
messages, so always keep them around.
The GPIO OMAP driver didn't have a consistent naming scheme for
all its functions. Some of them had an omap prefix while others
didn't. There are many advantages on having a separate namespace
for driver functions so let's add an "omap" prefix to all of them.
Signed-off-by: Javier Martinez Canillas <jmartinez@softcrates.net> Acked-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The <linux/irqchip/chained_irq.h> header is already included
when selecting GPIOLIB_IRQCHIP so there is no need to do it
in the driver. This is a left over from commit fb655f5
("gpio: omap: convert driver to use gpiolib irqchip").
Signed-off-by: Javier Martinez Canillas <jmartinez@softcrates.net> Acked-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO irqchips assign to the cascaded IRQs their own lock class
in order to avoid warnings about lockdep recursions since that
allow the lockdep core to keep track of things.
Since commit e45d1c80 ("gpio: put GPIO IRQs into their own lock class")
there is no need to do this in a driver if it's using the GPIO
irqchip helpers since gpiolib already assigns a lockdep class.
Signed-off-by: Javier Martinez Canillas <jmartinez@softcrates.net> Acked-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Andrew Ruder [Thu, 5 Jun 2014 19:13:23 +0000 (14:13 -0500)]
gpio-pxa: gpio0 and gpio1 support on dt
pxa_gpio_probe() has some issues supporting the gpio0 and gpio1
interrupts under device-tree - it never actually sets up the chain
handler to get interrupts on edge detect for GPIO0 and GPIO1.
1) Fix checksumming regressions, from Tom Herbert.
2) Undo unintentional permissions changes for SCTP rto_alpha and
rto_beta sysfs knobs, from Denial Borkmann.
3) VXLAN, like other IP tunnels, should advertize it's encapsulation
size using dev->needed_headroom instead of dev->hard_header_len.
From Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: sctp: fix permissions for rto_alpha and rto_beta knobs
vxlan: Checksum fixes
net: add skb_pop_rcv_encapsulation
udp: call __skb_checksum_complete when doing full checksum
net: Fix save software checksum complete
net: Fix GSO constants to match NETIF flags
udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
vxlan: use dev->needed_headroom instead of dev->hard_header_len
MAINTAINERS: update cxgb4 maintainer
Linus Torvalds [Mon, 16 Jun 2014 02:02:20 +0000 (16:02 -1000)]
Merge tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux
Pull more clock framework updates from Mike Turquette:
"This contains the second half the of the clk changes for 3.16.
They are simply fixes and code refactoring for the OMAP clock drivers.
The sunxi clock driver changes include splitting out the one
mega-driver into several smaller pieces and adding support for the A31
SoC clocks"
* tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
clk: sunxi: document PRCM clock compatible strings
clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
clk: sun6i: Protect SDRAM gating bit
clk: sun6i: Protect CPU clock
clk: sunxi: Rework clock protection code
clk: sunxi: Move the GMAC clock to a file of its own
clk: sunxi: Move the 24M oscillator to a file of its own
clk: sunxi: Remove calls to clk_put
clk: sunxi: document new A31 USB clock compatible
clk: sunxi: Implement A31 USB clock
ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
CLK: TI: gate: add composite interface clock to OMAP2 only build
ARM: OMAP2: clock: add DT boot support for cpufreq_ck
CLK: TI: OMAP2: add clock init support
...
Pull NVMe update from Matthew Wilcox:
"Mostly bugfixes again for the NVMe driver. I'd like to call out the
exported tracepoint in the block layer; I believe Keith has cleared
this with Jens.
We've had a few reports from people who're really pounding on NVMe
devices at scale, hence the timeout changes (and new module
parameters), hotplug cpu deadlock, tracepoints, and minor performance
tweaks"
[ Jens hadn't seen that tracepoint thing, but is ok with it - it will
end up going away when mq conversion happens ]
* git://git.infradead.org/users/willy/linux-nvme: (22 commits)
NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
NVMe: Use Log Page constants in SCSI emulation
NVMe: Define Log Page constants
NVMe: Fix hot cpu notification dead lock
NVMe: Rename io_timeout to nvme_io_timeout
NVMe: Use last bytes of f/w rev SCSI Inquiry
NVMe: Adhere to request queue block accounting enable/disable
NVMe: Fix nvme get/put queue semantics
NVMe: Delete NVME_GET_FEAT_TEMP_THRESH
NVMe: Make admin timeout a module parameter
NVMe: Make iod bio timeout a parameter
NVMe: Prevent possible NULL pointer dereference
NVMe: Fix the buffer size passed in GetLogPage(CDW10.NUMD)
NVMe: Update data structures for NVMe 1.2
NVMe: Enable BUILD_BUG_ON checks
NVMe: Update namespace and controller identify structures to the 1.1a spec
NVMe: Flush with data support
NVMe: Configure support for block flush
NVMe: Add tracepoints
NVMe: Protect against badly formatted CQEs
...
Daniel Borkmann [Sat, 14 Jun 2014 22:59:14 +0000 (00:59 +0200)]
net: sctp: fix permissions for rto_alpha and rto_beta knobs
Commit 3fd091e73b81 ("[SCTP]: Remove multiple levels of msecs
to jiffies conversions.") has silently changed permissions for
rto_alpha and rto_beta knobs from 0644 to 0444. The purpose of
this was to discourage users from tweaking rto_alpha and
rto_beta knobs in production environments since they are key
to correctly compute rtt/srtt.
RFC4960 under section 6.3.1. RTO Calculation says regarding
rto_alpha and rto_beta under rule C3 and C4:
[...]
C3) When a new RTT measurement R' is made, set
Note: The value of SRTT used in the update to RTTVAR
is its value before updating SRTT itself using the
second assignment. After the computation, update
RTO <- SRTT + 4 * RTTVAR.
C4) When data is in flight and when allowed by rule C5
below, a new RTT measurement MUST be made each round
trip. Furthermore, new RTT measurements SHOULD be
made no more than once per round trip for a given
destination transport address. There are two reasons
for this recommendation: First, it appears that
measuring more frequently often does not in practice
yield any significant benefit [ALLMAN99]; second,
if measurements are made more often, then the values
of RTO.Alpha and RTO.Beta in rule C3 above should be
adjusted so that SRTT and RTTVAR still adjust to
changes at roughly the same rate (in terms of how many
round trips it takes them to reflect new values) as
they would if making only one measurement per
round-trip and using RTO.Alpha and RTO.Beta as given
in rule C3. However, the exact nature of these
adjustments remains a research issue.
[...]
While it is discouraged to adjust rto_alpha and rto_beta
and not further specified how to adjust them, the RFC also
doesn't explicitly forbid it, but rather gives a RECOMMENDED
default value (rto_alpha=3, rto_beta=2). We have a couple
of users relying on the old permissions before they got
changed. That said, if someone really has the urge to adjust
them, we could allow it with a warning in the log.
Fixes: 3fd091e73b81 ("[SCTP]: Remove multiple levels of msecs to jiffies conversions.") Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Cc: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 15 Jun 2014 08:00:56 +0000 (01:00 -0700)]
Merge branch 'csum_fixes'
Tom Herbert says:
====================
Fixes related to some recent checksum modifications.
- Fix GSO constants to match NETIF flags
- Fix logic in saving checksum complete in __skb_checksum_complete
- Call __skb_checksum_complete from UDP if we are checksumming over
whole packet in order to save checksum.
- Fixes to VXLAN to work correctly with checksum complete
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 15 Jun 2014 06:24:28 +0000 (23:24 -0700)]
net: add skb_pop_rcv_encapsulation
This function is used by UDP encapsulation protocols in RX when
crossing encapsulation boundary. If ip_summed is set to
CHECKSUM_UNNECESSARY and encapsulation is not set, change to
CHECKSUM_NONE since the checksum has not been validated within the
encapsulation. Clears csum_valid by the same rationale.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 15 Jun 2014 06:24:20 +0000 (23:24 -0700)]
udp: call __skb_checksum_complete when doing full checksum
In __udp_lib_checksum_complete check if checksum is being done over all
the data (len is equal to skb->len) and if it is call
__skb_checksum_complete instead of __skb_checksum_complete_head. This
allows checksum to be saved in checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 15 Jun 2014 06:24:03 +0000 (23:24 -0700)]
net: Fix save software checksum complete
Geert reported issues regarding checksum complete and UDP.
The logic introduced in commit 7e3cead5172927732f51fde
("net: Save software checksum complete") is not correct.
This patch:
1) Restores code in __skb_checksum_complete_header except for setting
CHECKSUM_UNNECESSARY. This function may be calculating checksum on
something less than skb->len.
2) Adds saving checksum to __skb_checksum_complete. The full packet
checksum 0..skb->len is calculated without adding in pseudo header.
This value is saved in skb->csum and then the pseudo header is added
to that to derive the checksum for validation.
3) In both __skb_checksum_complete_header and __skb_checksum_complete,
set skb->csum_valid to whether checksum of zero was computed. This
allows skb_csum_unnecessary to return true without changing to
CHECKSUM_UNNECESSARY which was done previously.
4) Copy new csum related bits in __copy_skb_header.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 15 Jun 2014 06:23:52 +0000 (23:23 -0700)]
net: Fix GSO constants to match NETIF flags
Joseph Gasparakis reported that VXLAN GSO offload stopped working with
i40e device after recent UDP changes. The problem is that the
SKB_GSO_* bits are out of sync with the corresponding NETIF flags. This
patch fixes that. Also, we add BUILD_BUG_ONs in net_gso_ok for several
GSO constants that were missing to avoid the problem in the future.
Reported-by: Joseph Gasparakis <joseph.gasparakis@intel.com> Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 15 Jun 2014 00:49:48 +0000 (19:49 -0500)]
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is just a couple of drivers (hpsa and lpfc) that got left out for
further testing in linux-next. We also have one fix to a prior
submission (qla2xxx sparse)"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (36 commits)
qla2xxx: fix sparse warnings introduced by previous target mode t10-dif patch
lpfc: Update lpfc version to driver version 10.2.8001.0
lpfc: Fix ExpressLane priority setup
lpfc: mark old devices as obsolete
lpfc: Fix for initializing RRQ bitmap
lpfc: Fix for cleaning up stale ring flag and sp_queue_event entries
lpfc: Update lpfc version to driver version 10.2.8000.0
lpfc: Update Copyright on changed files from 8.3.45 patches
lpfc: Update Copyright on changed files
lpfc: Fixed locking for scsi task management commands
lpfc: Convert runtime references to old xlane cfg param to fof cfg param
lpfc: Fix FW dump using sysfs
lpfc: Fix SLI4 s abort loop to process all FCP rings and under ring_lock
lpfc: Fixed kernel panic in lpfc_abort_handler
lpfc: Fix locking for postbufq when freeing
lpfc: Fix locking for lpfc_hba_down_post
lpfc: Fix dynamic transitions of FirstBurst from on to off
hpsa: fix handling of hpsa_volume_offline return value
hpsa: return -ENOMEM not -1 on kzalloc failure in hpsa_get_device_id
hpsa: remove messages about volume status VPD inquiry page not supported
...
Linus Torvalds [Sun, 15 Jun 2014 00:48:43 +0000 (19:48 -0500)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull more btrfs updates from Chris Mason:
"This has a few fixes since our last pull and a new ioctl for doing
btree searches from userland. It's very similar to the existing
ioctl, but lets us return larger items back down to the app"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix error handling in create_pending_snapshot
btrfs: fix use of uninit "ret" in end_extent_writepage()
btrfs: free ulist in qgroup_shared_accounting() error path
Btrfs: fix qgroups sanity test crash or hang
btrfs: prevent RCU warning when dereferencing radix tree slot
Btrfs: fix unfinished readahead thread for raid5/6 degraded mounting
btrfs: new ioctl TREE_SEARCH_V2
btrfs: tree_search, search_ioctl: direct copy to userspace
btrfs: new function read_extent_buffer_to_user
btrfs: tree_search, copy_to_sk: return needed size on EOVERFLOW
btrfs: tree_search, copy_to_sk: return EOVERFLOW for too small buffer
btrfs: tree_search, search_ioctl: accept varying buffer
btrfs: tree_search: eliminate redundant nr_items check
Al Viro [Sat, 14 Jun 2014 06:12:41 +0000 (07:12 +0100)]
fix __swap_writepage() compile failure on old gcc versions
Tetsuo Handa wrote:
"Commit 62a8067a7f35 ("bio_vec-backed iov_iter") introduced an unnamed
union inside a struct which gcc-4.4.7 cannot handle. Name the unnamed
union as u in order to fix build failure"
Let's do this instead: there is only one place in the entire tree that
steps into this breakage. Anon structs and unions work in older gcc
versions; as the matter of fact, we have those in the tree - see e.g.
struct ieee80211_tx_info in include/net/mac80211.h
What doesn't work is handling their initializers:
struct {
int a;
union {
int b;
char c;
};
} x[2] = {{.a = 1, .c = 'a'}, {.a = 0, .b = 1}};
is the obvious syntax for initializer, perfectly fine for C11 and
handled correctly by gcc-4.7 or later.
Earlier versions, though, break on it - declaration is fine and so's
access to fields (i.e. x[0].c = 'a'; would produce the right code), but
members of the anon structs and unions are not inserted into the right
namespace. Tellingly, those older versions will not barf on struct {int
a; struct {int a;};}; - looks like they just have it hacked up somewhere
around the handling of . and -> instead of doing the right thing.
The easiest way to deal with that crap is to turn initialization of
those fields (in the only place where we have such initializer of
iov_iter) into plain assignment.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 14 Jun 2014 21:51:25 +0000 (14:51 -0700)]
Merge tag 'hsi-for-3.16-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi
Pull HSI build fixes from Sebastian Reichel:
- tighten dependency between ssi-protocol and omap-ssi to fix build
failures with randconfig.
- use normal module refcounting in omap driver to fix build with
disabled module support
* tag 'hsi-for-3.16-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi:
hsi: omap_ssi_port: use normal module refcounting
HSI: fix omap ssi driver dependency
Linus Torvalds [Sat, 14 Jun 2014 21:46:29 +0000 (14:46 -0700)]
Merge branch 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 vdso fixes from Peter Anvin:
"Fixes for x86/vdso.
One is a simple build fix for bigendian hosts, one is to make "make
vdso_install" work again, and the rest is about working around a bug
in Google's Go language -- two are documentation patches that improves
the sample code that the Go coders took, modified, and broke; the
other two implements a workaround that keeps existing Go binaries from
segfaulting at least"
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vdso: Fix vdso_install
x86/vdso: Hack to keep 64-bit Go programs working
x86/vdso: Add PUT_LE to store little-endian values
x86/vdso/doc: Make vDSO examples more portable
x86/vdso/doc: Rename vdso_test.c to vdso_standalone_test_x86.c
x86, vdso: Remove one final use of htole16()
Linus Torvalds [Sat, 14 Jun 2014 21:43:23 +0000 (14:43 -0700)]
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for Sensirion SHTC1 humidity / temperature sensor
- convert ltc4151 and vexpress drivers to use devm functions
- drop generic chip detection from lm85 driver
- avoid forward declarations in atxp1 driver
- fix sign extensions in ina2xx driver
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: vexpress: Use devm helper for hwmon device registration
hwmon: (atxp1) Avoid forward declaration
hwmon: add support for Sensirion SHTC1 sensor
hwmon: (ltc4151) Convert to devm_hwmon_device_register_with_groups
hwmon: (lm85) Drop generic detection
hwmon: (ina2xx) Cast to s16 on shunt and current regs
Eric Dumazet [Thu, 12 Jun 2014 23:13:06 +0000 (16:13 -0700)]
udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
Its too easy to add thousand of UDP sockets on a particular bucket,
and slow down an innocent multicast receiver.
Early demux is supposed to be an optimization, we should avoid spending
too much time in it.
It is interesting to note __udp4_lib_demux_lookup() only tries to
match first socket in the chain.
10 is the threshold we already have in __udp4_lib_lookup() to switch
to secondary hash.
Fixes: 421b3885bf6d5 ("udp: ipv4: Add udp early demux") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: David Held <drheld@google.com> Cc: Shawn Bohrer <sbohrer@rgmadvisors.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Thu, 12 Jun 2014 18:53:10 +0000 (11:53 -0700)]
vxlan: use dev->needed_headroom instead of dev->hard_header_len
When we mirror packets from a vxlan tunnel to other device,
the mirror device should see the same packets (that is, without
outer header). Because vxlan tunnel sets dev->hard_header_len,
tcf_mirred() resets mac header back to outer mac, the mirror device
actually sees packets with outer headers
Vxlan tunnel should set dev->needed_headroom instead of
dev->hard_header_len, like what other ip tunnels do. This fixes
the above problem.
Cc: "David S. Miller" <davem@davemloft.net> Cc: stephen hemminger <stephen@networkplumber.org> Cc: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: Cong Wang <cwang@twopensource.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Lutomirski [Thu, 12 Jun 2014 15:28:10 +0000 (08:28 -0700)]
x86/vdso: Fix vdso_install
"make vdso_install" installs unstripped versions of the vdso objects
for the benefit of the debugger. This was broken by checkin:
6f121e548f83 x86, vdso: Reimplement vdso.so preparation in build-time C
The filenames are different now, so update the Makefile to cope.
This still installs the 64-bit vdso as vdso64.so. We believe this
will be okay, as the only known user is a patched gdb which is known
to use build-ids, but if it turns out to be a problem we may have to
add a link.
Dan McLeran [Fri, 6 Jun 2014 14:27:27 +0000 (08:27 -0600)]
NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
This patch contains several fixes for Scsi START_STOP_UNIT. The previous
code did not account for signed vs. unsigned arithmetic which resulted
in an invalid lowest power state caculation when the device only supports
1 power state.
The code for Power Condition == 2 (Idle) was not following the spec. The
spec calls for setting the device to specific power states, depending
upon Power Condition Modifier, without accounting for the number of
power states supported by the device.
The code for Power Condition == 3 (Standby) was using a hard-coded '0'
which is replaced with the macro POWER_STATE_0.
Signed-off-by: Dan McLeran <daniel.mcleran@intel.com> Reviewed-by: Vishal Verma <vishal.l.verma@linux.intel.com> Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Eric Sandeen [Thu, 12 Jun 2014 05:53:44 +0000 (00:53 -0500)]
btrfs: fix error handling in create_pending_snapshot
fcebe456 cut and pasted some code to a later point
in create_pending_snapshot(), but didn't switch
to the appropriate error handling for this stage
of the function.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Chris Mason <clm@fb.com>
Eric Sandeen [Thu, 12 Jun 2014 05:39:58 +0000 (00:39 -0500)]
btrfs: fix use of uninit "ret" in end_extent_writepage()
If this condition in end_extent_writepage() is false:
if (tree->ops && tree->ops->writepage_end_io_hook)
we will then test an uninitialized "ret" at:
ret = ret < 0 ? ret : -EIO;
The test for ret is for the case where ->writepage_end_io_hook
failed, and we'd choose that ret as the error; but if
there is no ->writepage_end_io_hook, nothing sets ret.
Initializing ret to 0 should be sufficient; if
writepage_end_io_hook wasn't set, (!uptodate) means
non-zero err was passed in, so we choose -EIO in that case.
Signed-of-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Chris Mason <clm@fb.com>
Filipe Manana [Thu, 12 Jun 2014 01:47:37 +0000 (02:47 +0100)]
Btrfs: fix qgroups sanity test crash or hang
Often when running the qgroups sanity test, a crash or a hang happened.
This is because the extent buffer the test uses for the root node doesn't
have an header level explicitly set, making it have a random level value.
This is a problem when it's not zero for the btrfs_search_slot() calls
the test ends up doing, resulting in crashes or hangs such as the following:
Wang Shilong [Wed, 11 Jun 2014 02:55:22 +0000 (10:55 +0800)]
Btrfs: fix unfinished readahead thread for raid5/6 degraded mounting
Steps to reproduce:
# mkfs.btrfs -f /dev/sd[b-f] -m raid5 -d raid5
# mkfs.ext4 /dev/sdc --->corrupt one of btrfs device
# mount /dev/sdb /mnt -o degraded
# btrfs scrub start -BRd /mnt
This is because readahead would skip missing device, this is not true
for RAID5/6, because REQ_GET_READ_MIRRORS return 1 for RAID5/6 block
mapping. If expected data locates in missing device, readahead thread
would not call __readahead_hook() which makes event @rc->elems=0
wait forever.
Fix this problem by checking return value of btrfs_map_block(),we
can only skip missing device safely if there are several mirrors.
Signed-off-by: Wang Shilong <wangsl.fnst@cn.fujitsu.com> Signed-off-by: Chris Mason <clm@fb.com>
Gerhard Heift [Thu, 30 Jan 2014 15:24:03 +0000 (16:24 +0100)]
btrfs: new ioctl TREE_SEARCH_V2
This new ioctl call allows the user to supply a buffer of varying size in which
a tree search can store its results. This is much more flexible if you want to
receive items which are larger than the current fixed buffer of 3992 bytes or
if you want to fetch more items at once. Items larger than this buffer are for
example some of the type EXTENT_CSUM.
Signed-off-by: Gerhard Heift <Gerhard@Heift.Name> Signed-off-by: Chris Mason <clm@fb.com> Acked-by: David Sterba <dsterba@suse.cz>
Keith Busch [Wed, 11 Jun 2014 17:51:35 +0000 (11:51 -0600)]
NVMe: Fix hot cpu notification dead lock
There is a potential dead lock if a cpu event occurs during nvme probe
since it registered with hot cpu notification. This fixes the race by
having the module register with notification outside of probe rather
than have each device register.
The actual work is done in a scheduled work queue instead of in the
notifier since assigning IO queues has the potential to block if the
driver creates additional queues.
Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Linus Torvalds [Fri, 13 Jun 2014 14:42:49 +0000 (07:42 -0700)]
Merge tag 'sound-fix-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Most of changes are small and easy cleanup or fixes:
- a few HD-audio Realtek codec fixes and quirks
- Intel HDMI audio fixes for Broadwell and Haswell / ValleyView
- FireWire sound stack cleanups
- a couple of sequencer core fixes
- compress ABI fix for 64bit
- conversion to modern ktime*() API"
* tag 'sound-fix-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (23 commits)
ALSA: hda/realtek - Add more entry for enable HP mute led
ALSA: hda - Add quirk for external mic on Lifebook U904
ALSA: hda - fix a fixup value for codec alc293 in the pin_quirk table
ALSA: intel8x0: Use ktime and ktime_get()
ALSA: core: Use ktime_get_ts()
ALSA: hda - verify pin:converter connection on unsol event for HSW and VLV
ALSA: compress: Cancel the optimization of compiler and fix the size of struct for all platform.
ALSA: hda - Add quirk for ABit AA8XE
Revert "ALSA: hda - mask buggy stream DMA0 for Broadwell display controller"
ALSA: hda - using POS_FIX_LPIB on Broadwell HDMI Audio
ALSA: hda/realtek - Add support of ALC667 codec
ALSA: hda/realtek - Add more codec rename
ALSA: hda/realtek - New vendor ID for ALC233
ALSA: hda - add two new pin tables
ALSA: hda/realtek - Add support of ALC891 codec
ALSA: seq: Continue broadcasting events to ports if one of them fails
ALSA: bebob: Remove unused function prototype
ALSA: fireworks: Remove meaningless mutex_destroy()
ALSA: fireworks: Remove a constant over width to which it's applied
ALSA: fireworks: Improve comments about Fireworks transaction
...
Linus Torvalds [Fri, 13 Jun 2014 14:39:39 +0000 (07:39 -0700)]
Merge branch 'serge-next-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sergeh/linux-security
Pull more security layer updates from Serge Hallyn:
"A few more commits had previously failed to make it through
security-next into linux-next but this week made it into linux-next.
At least commit "ima: introduce ima_kernel_read()" was deemed critical
by Mimi to make this merge window.
This is a temporary tree just for this request. Mimi has pointed me
to some previous threads about keeping maintainer trees at the
previous release, which I'll certainly do for anything long-term,
after talking with James"
* 'serge-next-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sergeh/linux-security:
ima: introduce ima_kernel_read()
evm: prohibit userspace writing 'security.evm' HMAC value
ima: check inode integrity cache in violation check
ima: prevent unnecessary policy checking
evm: provide option to protect additional SMACK xattrs
evm: replace HMAC version with attribute mask
ima: prevent new digsig xattr from being replaced
ALSA: hda - Add quirk for external mic on Lifebook U904
According to the bug reporter (Данило Шеган), the external mic
starts to work and has proper jack detection if only pin 0x19
is marked properly as an external headset mic.
AlsaInfo at https://bugs.launchpad.net/ubuntu/+source/pulseaudio/+bug/1328587/+attachment/4128991/+files/AlsaInfo.txt
Hui Wang [Fri, 13 Jun 2014 01:23:10 +0000 (09:23 +0800)]
ALSA: hda - fix a fixup value for codec alc293 in the pin_quirk table
The fixup value for codec alc293 was set to
ALC269_FIXUP_DELL1_MIC_NO_PRESENCE by a mistake, if we don't fix it,
the Dock mic will be overwriten by the headset mic, this will make
the Dock mic can't work.
Cc: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Fri, 13 Jun 2014 06:06:23 +0000 (23:06 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph updates from Sage Weil:
"This has a mix of bug fixes and cleanups.
Alex's patch fixes a rare race in RBD. Ilya's patches fix an ENOENT
check when a second rbd image is mapped and a couple memory leaks.
Zheng fixes several issues with fragmented directories and multiple
MDSs. Josh fixes a spin/sleep issue, and Josh and Guangliang's
patches fix setting and unsetting RBD images read-only.
Naturally there are several other cleanups mixed in for good measure"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (23 commits)
rbd: only set disk to read-only once
rbd: move calls that may sleep out of spin lock range
rbd: add ioctl for rbd
ceph: use truncate_pagecache() instead of truncate_inode_pages()
ceph: include time stamp in every MDS request
rbd: fix ida/idr memory leak
rbd: use reference counts for image requests
rbd: fix osd_request memory leak in __rbd_dev_header_watch_sync()
rbd: make sure we have latest osdmap on 'rbd map'
libceph: add ceph_monc_wait_osdmap()
libceph: mon_get_version request infrastructure
libceph: recognize poolop requests in debugfs
ceph: refactor readpage_nounlock() to make the logic clearer
mds: check cap ID when handling cap export message
ceph: remember subtree root dirfrag's auth MDS
ceph: introduce ceph_fill_fragtree()
ceph: handle cap import atomically
ceph: pre-allocate ceph_cap struct for ceph_add_cap()
ceph: update inode fields according to issued caps
rbd: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
...
Linus Torvalds [Fri, 13 Jun 2014 06:04:28 +0000 (23:04 -0700)]
Merge branch 'topic/omap3isp' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull OMAP3 updates from Mauro Carvalho Chehab:
"Some driver improvements on OMAP3. This series depend on some iommu
patches already merged"
* 'topic/omap3isp' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (26 commits)
[media] omap3isp: Rename isp_buffer isp_addr field to dma
[media] omap3isp: Move to videobuf2
[media] v4l: vb2: Add a function to discard all DONE buffers
[media] omap3isp: Cancel all queued buffers when stopping the video stream
[media] omap3isp: Move buffer irqlist to isp_buffer structure
[media] omap3isp: Move queue irqlock to isp_video structure
[media] omap3isp: Move queue mutex to isp_video structure
[media] omap3isp: queue: Don't build scatterlist for kernel buffer
[media] omap3isp: Use the ARM DMA IOMMU-aware operations
[media] omap3isp: queue: Use sg_alloc_table_from_pages()
[media] omap3isp: queue: Map PFNMAP buffers to device
[media] omap3isp: queue: Fix the dma_map_sg() return value check
[media] omap3isp: queue: Allocate kernel buffers with dma_alloc_coherent
[media] omap3isp: queue: Inline the ispmmu_v(un)map functions
[media] omap3isp: queue: Merge the prepare and sglist functions
[media] omap3isp: queue: Use sg_table structure
[media] omap3isp: queue: Move IOMMU handling code to the queue
[media] omap3isp: video: Set the buffer bytesused field at completion time
[media] omap3isp: ccdc: Use the DMA API for FPC
[media] omap3isp: ccdc: Use the DMA API for LSC
...
Linus Torvalds [Fri, 13 Jun 2014 05:38:32 +0000 (22:38 -0700)]
Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Add support for T10 PI pass-through between vhost-scsi +
virtio-scsi (MST + Paolo + MKP + nab)
- Add support for T10 PI in qla2xxx target mode (Quinn + MKP + hch +
nab, merged through scsi.git)
- Add support for percpu-ida pre-allocation in qla2xxx target code
(Quinn + nab)
- A number of iser-target fixes related to hardening the network
portal shutdown path (Sagi + Slava)
- Fix response length residual handling for a number of control CDBs
(Roland + Christophe V.)
- Various iscsi RFC conformance fixes in the CHAP authentication path
(Tejas and Calsoft folks + nab)
- Return TASK_SET_FULL status for tcm_fc(FCoE) DataIn + Response
failures (Vasu + Jun + nab)
- Fix long-standing ABORT_TASK + session reset hang (nab)
- Convert iser-initiator + iser-target to include T10 bytes into EDTL
(Sagi + Or + MKP + Mike Christie)
- Fix NULL pointer dereference regression related to XCOPY introduced
in v3.15 + CC'ed to v3.12.y (nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (34 commits)
target: Fix NULL pointer dereference for XCOPY in target_put_sess_cmd
vhost-scsi: Include prot_bytes into expected data transfer length
TARGET/sbc,loopback: Adjust command data length in case pi exists on the wire
libiscsi, iser: Adjust data_length to include protection information
scsi_cmnd: Introduce scsi_transfer_length helper
target: Report correct response length for some commands
target/sbc: Check that the LBA and number of blocks are correct in VERIFY
target/sbc: Remove sbc_check_valid_sectors()
Target/iscsi: Fix sendtargets response pdu for iser transport
Target/iser: Fix a wrong dereference in case discovery session is over iser
iscsi-target: Fix ABORT_TASK + connection reset iscsi_queue_req memory leak
target: Use complete_all for se_cmd->t_transport_stop_comp
target: Set CMD_T_ACTIVE bit for Task Management Requests
target: cleanup some boolean tests
target/spc: Simplify INQUIRY EVPD=0x80
tcm_fc: Generate TASK_SET_FULL status for response failures
tcm_fc: Generate TASK_SET_FULL status for DataIN failures
iscsi-target: Reject mutual authentication with reflected CHAP_C
iscsi-target: Remove no-op from iscsit_tpg_del_portal_group
iscsi-target: Fix CHAP_A parameter list handling
...
Linus Torvalds [Fri, 13 Jun 2014 04:29:20 +0000 (21:29 -0700)]
Merge branch 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild misc updates from Michal Marek:
"This is the non-critical part of kbuild for v3.16-rc1:
- make deb-pkg can do s390x and arm64
- new patterns in scripts/tags.sh
- scripts/tags.sh skips userspace tools' sources (which sometimes
have copies of kernel structures) and symlinks
- improvements to the objdiff tool
- two new coccinelle patches
- other minor fixes"
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scripts: objdiff: support directories for the augument of record command
scripts: objdiff: fix a comment
scripts: objdiff: change the extension of disassembly from .o to .dis
scripts: objdiff: improve path flexibility for record command
scripts: objdiff: remove unnecessary code
scripts: objdiff: direct error messages to stderr
scripts: objdiff: get the path to .tmp_objdiff more simply
deb-pkg: Add automatic support for s390x architecture
coccicheck: Add unneeded return variable test
kbuild: Fix a typo in documentation
kbuild: trivial - use tabs for code indent where possible
kbuild: trivial - remove trailing empty lines
coccinelle: Check for missing NULL terminators in of_device_id tables
scripts/tags.sh: ignore symlink'ed source files
scripts/tags.sh: add regular expression replacement pattern for memcg
builddeb: add arm64 in the supported architectures
builddeb: use $OBJCOPY variable instead of objcopy
scripts/tags.sh: ignore code of user space tools
scripts/tags.sh: add pattern for DEFINE_HASHTABLE
.gitignore: ignore Module.symvers in all directories
Linus Torvalds [Fri, 13 Jun 2014 04:23:38 +0000 (21:23 -0700)]
Merge branch 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild updates from Michal Marek:
"Kbuild changes for v3.16-rc1:
- cross-compilation fix so that cc-option is testing the right
compiler
- Fix for make defconfig all
- Using relative paths to the object and source directory where
possible, plus fixes for the fallout of the change
- several cleanups in the Makefiles and scripts
The powerpc fix is from today, because it was only discovered
recently. The rest has been in linux-next for some time"
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
powerpc: Avoid circular dependency with zImage.%
kbuild: create include/config directory in scripts/kconfig/Makefile
kbuild: do not create include/linux directory
Makefile: Fix unrecognized cross-compiler command line options
kbuild: do not add "selinux" to subdir- twice
um: Fix for relative objtree when generating x86 headers
kbuild: Use relative path when building in a subdir of the source tree
kbuild: Use relative path when building in the source tree
kbuild: Use relative path for $(objtree)
firmware: Use $(quote) in the Makefile
firmware: Simplify directory creation
kbuild: trivial - fix comment block indent
kbuild: trivial - remove trailing spaces
kbuild: support simultaneous "make %config" and "make all"
kbuild: move extra gcc checks to scripts/Makefile.extrawarn
Linus Torvalds [Fri, 13 Jun 2014 04:07:25 +0000 (21:07 -0700)]
Merge tag 'trace-3.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing cleanups and bugfixes from Steven Rostedt:
"One bug fix that goes back to 3.10. Accessing a non existent buffer
if "possible cpus" is greater than actual CPUs (including offline
CPUs).
Namhyung Kim did some reviews of the patches I sent this merge window
and found a memory leak and had a few clean ups"
* tag 'trace-3.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix check of ftrace_trace_arrays list_empty() check
tracing: Fix leak of per cpu max data in instances
tracing: Cleanup saved_cmdlines_size changes
ring-buffer: Check if buffer exists before polling
Linus Torvalds [Fri, 13 Jun 2014 03:11:38 +0000 (20:11 -0700)]
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull more powerpc updates from Ben Herrenschmidt:
"Here are the remaining bits I was mentioning earlier. Mostly bug
fixes and new selftests from Michael (yay !). He also removed the WSP
platform and A2 core support which were dead before release, so less
clutter.
One little "feature" I snuck in is the doorbell IPI support for
non-virtualized P8 which speeds up IPIs significantly between threads
of a core"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (34 commits)
powerpc/book3s: Fix some ABIv2 issues in machine check code
powerpc/book3s: Fix guest MC delivery mechanism to avoid soft lockups in guest.
powerpc/book3s: Increment the mce counter during machine_check_early call.
powerpc/book3s: Add stack overflow check in machine check handler.
powerpc/book3s: Fix machine check handling for unhandled errors
powerpc/eeh: Dump PE location code
powerpc/powernv: Enable POWER8 doorbell IPIs
powerpc/cpuidle: Only clear LPCR decrementer wakeup bit on fast sleep entry
powerpc/powernv: Fix killed EEH event
powerpc: fix typo 'CONFIG_PMAC'
powerpc: fix typo 'CONFIG_PPC_CPU'
powerpc/powernv: Don't escalate non-existing frozen PE
powerpc/eeh: Report frozen parent PE prior to child PE
powerpc/eeh: Clear frozen state for child PE
powerpc/powernv: Reduce panic timeout from 180s to 10s
powerpc/xmon: avoid format string leaking to printk
selftests/powerpc: Add tests of PMU EBBs
selftests/powerpc: Add support for skipping tests
selftests/powerpc: Put the test in a separate process group
selftests/powerpc: Fix instruction loop for ABIv2 (LE)
...
Linus Torvalds [Fri, 13 Jun 2014 03:08:47 +0000 (20:08 -0700)]
Merge tag 'blackfin-for-linus' of http://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux
Pull blackfin updates from Steven Miao.
* tag 'blackfin-for-linus' of http://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux:
blackfin: defconfigs: add MTD_SPI_NOR (new dependency for M25P80)
Revert "blackfin: dma: current count mmr is read only"
bf533: fix build error: add linux/gpio.h
Linus Torvalds [Fri, 13 Jun 2014 03:03:47 +0000 (20:03 -0700)]
Merge branch 'x86-irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 irq fixes from Ingo Molnar:
"Two changes: a cpu-hotplug/irq race fix, plus a HyperV related fix"
* 'x86-irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/irq: Fix fixup_irqs() error handling
x86, irq, pic: Probe for legacy PIC and set legacy_pic appropriately
Linus Torvalds [Fri, 13 Jun 2014 02:42:15 +0000 (19:42 -0700)]
Merge branch 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull more scheduler updates from Ingo Molnar:
"Second round of scheduler changes:
- try-to-wakeup and IPI reduction speedups, from Andy Lutomirski
- continued power scheduling cleanups and refactorings, from Nicolas
Pitre
- misc fixes and enhancements"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Delete extraneous extern for to_ratio()
sched/idle: Optimize try-to-wake-up IPI
sched/idle: Simplify wake_up_idle_cpu()
sched/idle: Clear polling before descheduling the idle thread
sched, trace: Add a tracepoint for IPI-less remote wakeups
cpuidle: Set polling in poll_idle
sched: Remove redundant assignment to "rt_rq" in update_curr_rt(...)
sched: Rename capacity related flags
sched: Final power vs. capacity cleanups
sched: Remove remaining dubious usage of "power"
sched: Let 'struct sched_group_power' care about CPU capacity
sched/fair: Disambiguate existing/remaining "capacity" usage
sched/fair: Change "has_capacity" to "has_free_capacity"
sched/fair: Remove "power" from 'struct numa_stats'
sched: Fix signedness bug in yield_to()
sched/fair: Use time_after() in record_wakee()
sched/balancing: Reduce the rate of needless idle load balancing
sched/fair: Fix unlocked reads of some cfs_b->quota/period
Linus Torvalds [Fri, 13 Jun 2014 02:18:49 +0000 (19:18 -0700)]
Merge branch 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull more perf updates from Ingo Molnar:
"A second round of perf updates:
- wide reaching kprobes sanitization and robustization, with the hope
of fixing all 'probe this function crashes the kernel' bugs, by
Masami Hiramatsu.
- uprobes updates from Oleg Nesterov: tmpfs support, corner case
fixes and robustization work.
- perf tooling updates and fixes from Jiri Olsa, Namhyung Ki, Arnaldo
et al:
* Add support to accumulate hist periods (Namhyung Kim)
* various fixes, refactorings and enhancements"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (101 commits)
perf: Differentiate exec() and non-exec() comm events
perf: Fix perf_event_comm() vs. exec() assumption
uprobes/x86: Rename arch_uprobe->def to ->defparam, minor comment updates
perf/documentation: Add description for conditional branch filter
perf/x86: Add conditional branch filtering support
perf/tool: Add conditional branch filter 'cond' to perf record
perf: Add new conditional branch filter 'PERF_SAMPLE_BRANCH_COND'
uprobes: Teach copy_insn() to support tmpfs
uprobes: Shift ->readpage check from __copy_insn() to uprobe_register()
perf/x86: Use common PMU interrupt disabled code
perf/ARM: Use common PMU interrupt disabled code
perf: Disable sampled events if no PMU interrupt
perf: Fix use after free in perf_remove_from_context()
perf tools: Fix 'make help' message error
perf record: Fix poll return value propagation
perf tools: Move elide bool into perf_hpp_fmt struct
perf tools: Remove elide setup for SORT_MODE__MEMORY mode
perf tools: Fix "==" into "=" in ui_browser__warning assignment
perf tools: Allow overriding sysfs and proc finding with env var
perf tools: Consider header files outside perf directory in tags target
...
Andy Lutomirski [Fri, 13 Jun 2014 00:53:12 +0000 (17:53 -0700)]
x86/vdso: Hack to keep 64-bit Go programs working
The Go runtime has a buggy vDSO parser that currently segfaults.
This writes an empty SHT_DYNSYM entry that causes Go's runtime to
malfunction by thinking that the vDSO is empty rather than
malfunctioning by running off the end and segfaulting.
This affects x86-64 only as far as we know, so we do not need this for
the i386 and x32 vdsos.
Linus Torvalds [Fri, 13 Jun 2014 01:48:15 +0000 (18:48 -0700)]
Merge branch 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull more locking changes from Ingo Molnar:
"This is the second round of locking tree updates for v3.16, offering
large system scalability improvements:
- optimistic spinning for rwsems, from Davidlohr Bueso.
- 'qrwlocks' core code and x86 enablement, from Waiman Long and PeterZ"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, locking/rwlocks: Enable qrwlocks on x86
locking/rwlocks: Introduce 'qrwlocks' - fair, queued rwlocks
locking/mutexes: Documentation update/rewrite
locking/rwsem: Fix checkpatch.pl warnings
locking/rwsem: Fix warnings for CONFIG_RWSEM_GENERIC_SPINLOCK
locking/rwsem: Support optimistic spinning
Gerhard Heift [Thu, 30 Jan 2014 15:23:59 +0000 (16:23 +0100)]
btrfs: tree_search, copy_to_sk: return EOVERFLOW for too small buffer
In copy_to_sk, if an item is too large for the given buffer, it now returns
-EOVERFLOW instead of copying a search_header with len = 0. For backward
compatibility for the first item it still copies such a header to the buffer,
but not any other following items, which could have fitted.
tree_search changes -EOVERFLOW back to 0 to behave similiar to the way it
behaved before this patch.
Signed-off-by: Gerhard Heift <Gerhard@Heift.Name> Signed-off-by: Chris Mason <clm@fb.com> Acked-by: David Sterba <dsterba@suse.cz>
If the amount of items reached the given limit of nr_items, we can leave
copy_to_sk without updating the key. Also by returning 1 we leave the loop in
search_ioctl without rechecking if we reached the given limit.
Signed-off-by: Gerhard Heift <Gerhard@Heift.Name> Signed-off-by: Chris Mason <clm@fb.com> Acked-by: David Sterba <dsterba@suse.cz>
Dmitry Kasatkin [Thu, 8 May 2014 11:03:22 +0000 (14:03 +0300)]
ima: introduce ima_kernel_read()
Commit 8aac62706 "move exit_task_namespaces() outside of exit_notify"
introduced the kernel opps since the kernel v3.10, which happens when
Apparmor and IMA-appraisal are enabled at the same time.
The reason for the oops is that IMA-appraisal uses "kernel_read()" when
file is closed. kernel_read() honors LSM security hook which calls
Apparmor handler, which uses current->nsproxy->mnt_ns. The 'guilty'
commit changed the order of cleanup code so that nsproxy->mnt_ns was
not already available for Apparmor.
Discussion about the issue with Al Viro and Eric W. Biederman suggested
that kernel_read() is too high-level for IMA. Another issue, except
security checking, that was identified is mandatory locking. kernel_read
honors it as well and it might prevent IMA from calculating necessary hash.
It was suggested to use simplified version of the function without security
and locking checks.
This patch introduces special version ima_kernel_read(), which skips security
and mandatory locking checking. It prevents the kernel oops to happen.
Signed-off-by: Dmitry Kasatkin <d.kasatkin@samsung.com> Suggested-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com> Cc: <stable@vger.kernel.org>
Mimi Zohar [Sun, 11 May 2014 04:05:23 +0000 (00:05 -0400)]
evm: prohibit userspace writing 'security.evm' HMAC value
Calculating the 'security.evm' HMAC value requires access to the
EVM encrypted key. Only the kernel should have access to it. This
patch prevents userspace tools(eg. setfattr, cp --preserve=xattr)
from setting/modifying the 'security.evm' HMAC value directly.
Dmitry Kasatkin [Thu, 27 Mar 2014 08:29:28 +0000 (10:29 +0200)]
ima: check inode integrity cache in violation check
When IMA did not support ima-appraisal, existance of the S_IMA flag
clearly indicated that the file was measured. With IMA appraisal S_IMA
flag indicates that file was measured and/or appraised. Because of
this, when measurement is not enabled by the policy, violations are
still reported.
To differentiate between measurement and appraisal policies this
patch checks the inode integrity cache flags. The IMA_MEASURED
flag indicates whether the file was actually measured, while the
IMA_MEASURE flag indicates whether the file should be measured.
Unfortunately, the IMA_MEASURED flag is reset to indicate the file
needs to be re-measured. Thus, this patch checks the IMA_MEASURE
flag.
This patch limits the false positive violation reports, but does
not fix it entirely. The IMA_MEASURE/IMA_MEASURED flags are
indications that, at some point in time, the file opened for read
was in policy, but might not be in policy now (eg. different uid).
Other changes would be needed to further limit false positive
violation reports.
Changelog:
- expanded patch description based on conversation with Roberto (Mimi)
projects / mirror_ubuntu-eoan-kernel.git / log