Vladimir Oltean [Tue, 7 Feb 2023 18:31:17 +0000 (20:31 +0200)]
net: mscc: ocelot: fix all IPv6 getting trapped to CPU when PTP timestamping is used
While running this selftest which usually passes:
~/selftests/drivers/net/dsa# ./local_termination.sh eno0 swp0
TEST: swp0: Unicast IPv4 to primary MAC address [ OK ]
TEST: swp0: Unicast IPv4 to macvlan MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, promisc [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, allmulti [ OK ]
TEST: swp0: Multicast IPv4 to joined group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, allmulti [ OK ]
TEST: swp0: Multicast IPv6 to joined group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, allmulti [ OK ]
if I start PTP timestamping then run it again (debug prints added by me),
the unknown IPv6 MC traffic is seen by the CPU port even when it should
have been dropped:
~/selftests/drivers/net/dsa# ptp4l -i swp0 -2 -P -m
ptp4l[225.410]: selected /dev/ptp1 as PTP clock
[ 225.445746] mscc_felix 0000:00:00.5: ocelot_l2_ptp_trap_add: port 0 adding L2 PTP trap
[ 225.453815] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_add: port 0 adding IPv4 PTP event trap
[ 225.462703] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_add: port 0 adding IPv4 PTP general trap
[ 225.471768] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_add: port 0 adding IPv6 PTP event trap
[ 225.480651] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_add: port 0 adding IPv6 PTP general trap
ptp4l[225.488]: port 1: INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[225.488]: port 0: INITIALIZING to LISTENING on INIT_COMPLETE
^C
~/selftests/drivers/net/dsa# ./local_termination.sh eno0 swp0
TEST: swp0: Unicast IPv4 to primary MAC address [ OK ]
TEST: swp0: Unicast IPv4 to macvlan MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, promisc [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, allmulti [ OK ]
TEST: swp0: Multicast IPv4 to joined group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, allmulti [ OK ]
TEST: swp0: Multicast IPv6 to joined group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group [FAIL]
reception succeeded, but should have failed
TEST: swp0: Multicast IPv6 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, allmulti [ OK ]
The PGID_MCIPV6 is configured correctly to not flood to the CPU,
I checked that.
Furthermore, when I disable back PTP RX timestamping (ptp4l doesn't do
that when it exists), packets are RX filtered again as they should be:
~/selftests/drivers/net/dsa# hwstamp_ctl -i swp0 -r 0
[ 218.202854] mscc_felix 0000:00:00.5: ocelot_l2_ptp_trap_del: port 0 removing L2 PTP trap
[ 218.212656] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_del: port 0 removing IPv4 PTP event trap
[ 218.222975] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_del: port 0 removing IPv4 PTP general trap
[ 218.233133] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_del: port 0 removing IPv6 PTP event trap
[ 218.242251] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_del: port 0 removing IPv6 PTP general trap
current settings:
tx_type 1
rx_filter 12
new settings:
tx_type 1
rx_filter 0
~/selftests/drivers/net/dsa# ./local_termination.sh eno0 swp0
TEST: swp0: Unicast IPv4 to primary MAC address [ OK ]
TEST: swp0: Unicast IPv4 to macvlan MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, promisc [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, allmulti [ OK ]
TEST: swp0: Multicast IPv4 to joined group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, allmulti [ OK ]
TEST: swp0: Multicast IPv6 to joined group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, allmulti [ OK ]
So it's clear that something in the PTP RX trapping logic went wrong.
Looking a bit at the code, I can see that there are 4 typos, which
populate "ipv4" VCAP IS2 key filter fields for IPv6 keys.
VCAP IS2 keys of type OCELOT_VCAP_KEY_IPV4 and OCELOT_VCAP_KEY_IPV6 are
handled by is2_entry_set(). OCELOT_VCAP_KEY_IPV4 looks at
&filter->key.ipv4, and OCELOT_VCAP_KEY_IPV6 at &filter->key.ipv6.
Simply put, when we populate the wrong key field, &filter->key.ipv6
fields "proto.mask" and "proto.value" remain all zeroes (or "don't care").
So is2_entry_set() will enter the "else" of this "if" condition:
if (msk == 0xff && (val == IPPROTO_TCP || val == IPPROTO_UDP))
and proceed to ignore the "proto" field. The resulting rule will match
on all IPv6 traffic, trapping it to the CPU.
This is the reason why the local_termination.sh selftest sees it,
because control traps are stronger than the PGID_MCIPV6 used for
flooding (from the forwarding data path).
But the problem is in fact much deeper. We trap all IPv6 traffic to the
CPU, but if we're bridged, we set skb->offload_fwd_mark = 1, so software
forwarding will not take place and IPv6 traffic will never reach its
destination.
The fix is simple - correct the typos.
I was intentionally inaccurate in the commit message about the breakage
occurring when any PTP timestamping is enabled. In fact it only happens
when L4 timestamping is requested (HWTSTAMP_FILTER_PTP_V2_EVENT or
HWTSTAMP_FILTER_PTP_V2_L4_EVENT). But ptp4l requests a larger RX
timestamping filter than it needs for "-2": HWTSTAMP_FILTER_PTP_V2_EVENT.
I wanted people skimming through git logs to not think that the bug
doesn't affect them because they only use ptp4l in L2 mode.
Fixes: 96ca08c05838 ("net: mscc: ocelot: set up traps for PTP packets") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230207183117.1745754-1-vladimir.oltean@nxp.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Pietro Borrello [Tue, 7 Feb 2023 18:26:34 +0000 (18:26 +0000)]
rds: rds_rm_zerocopy_callback() use list_first_entry()
rds_rm_zerocopy_callback() uses list_entry() on the head of a list
causing a type confusion.
Use list_first_entry() to actually access the first element of the
rs_zcookie_queue list.
Fixes: 9426bbc6de99 ("rds: use list structure to track information for zerocopy completion notification") Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it> Link: https://lore.kernel.org/r/20230202-rds-zerocopy-v3-1-83b0df974f9a@diag.uniroma1.it Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Thu, 9 Feb 2023 05:35:38 +0000 (21:35 -0800)]
Merge tag 'ipsec-2023-02-08' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
ipsec 2023-02-08
1) Fix policy checks for nested IPsec tunnels when using
xfrm interfaces. From Benedict Wong.
2) Fix netlink message expression on 32=>64-bit
messages translators. From Anastasia Belova.
3) Prevent potential spectre v1 gadget in xfrm_xlate32_attr.
From Eric Dumazet.
4) Always consistently use time64_t in xfrm_timer_handler.
From Eric Dumazet.
5) Fix KCSAN reported bug: Multiple cpus can update use_time
at the same time. From Eric Dumazet.
6) Fix SCP copy from IPv4 to IPv6 on interfamily tunnel.
From Christian Hopps.
* tag 'ipsec-2023-02-08' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec:
xfrm: fix bug with DSCP copy to v6 from v4 tunnel
xfrm: annotate data-race around use_time
xfrm: consistently use time64_t in xfrm_timer_handler()
xfrm/compat: prevent potential spectre v1 gadget in xfrm_xlate32_attr()
xfrm: compat: change expression for switch in xfrm_xlate64
Fix XFRM-I support for nested ESP tunnels
====================
Jakub Kicinski [Thu, 9 Feb 2023 03:23:44 +0000 (19:23 -0800)]
Merge tag 'mlx5-fixes-2023-02-07' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2023-02-07
This series provides bug fixes to mlx5 driver.
* tag 'mlx5-fixes-2023-02-07' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Serialize module cleanup with reload and remove
net/mlx5: fw_tracer, Zero consumer index when reloading the tracer
net/mlx5: fw_tracer, Clear load bit when freeing string DBs buffers
net/mlx5: Expose SF firmware pages counter
net/mlx5: Store page counters in a single array
net/mlx5e: IPoIB, Show unknown speed instead of error
net/mlx5e: Fix crash unsetting rx-vlan-filter in switchdev mode
net/mlx5: Bridge, fix ageing of peer FDB entries
net/mlx5: DR, Fix potential race in dr_rule_create_rule_nic
net/mlx5e: Update rx ring hw mtu upon each rx-fcs flag change
====================
David S. Miller [Wed, 8 Feb 2023 09:39:34 +0000 (09:39 +0000)]
Merge branch 'mptcp-fixes'
Matthieu Baerts says:
====================
mptcp: fixes for v6.2
Patch 1 clears resources earlier if there is no more reasons to keep
MPTCP sockets alive.
Patches 2 and 3 fix some locking issues visible in some rare corner
cases: the linked issues should be quite hard to reproduce.
Patch 4 makes sure subflows are correctly cleaned after the end of a
connection.
Patch 5 and 6 improve the selftests stability when running in a slow
environment by transfering data for a longer period on one hand and by
stopping the tests when all expected events have been observed on the
other hand.
All these patches fix issues introduced before v6.2.
====================
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Matthieu Baerts [Tue, 7 Feb 2023 13:04:18 +0000 (14:04 +0100)]
selftests: mptcp: stop tests earlier
These 'endpoint' tests from 'mptcp_join.sh' selftest start a transfer in
the background and check the status during this transfer.
Once the expected events have been recorded, there is no reason to wait
for the data transfer to finish. It can be stopped earlier to reduce the
execution time by more than half.
For these tests, the exchanged data were not verified. Errors, if any,
were ignored but that's fine, plenty of other tests are looking at that.
It is then OK to mute stderr now that we are sure errors will be printed
(and still ignored) because the transfer is stopped before the end.
Fixes: e274f7154008 ("selftests: mptcp: add subflow limits test-cases") Cc: stable@vger.kernel.org Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 7 Feb 2023 13:04:17 +0000 (14:04 +0100)]
selftests: mptcp: allow more slack for slow test-case
A test-case is frequently failing on some extremely slow VMs.
The mptcp transfer completes before the script is able to do
all the required PM manipulation.
Address the issue in the simplest possible way, making the
transfer even more slow.
Additionally dump more info in case of failures, to help debugging
similar problems in the future and init dump_stats var.
Fixes: e274f7154008 ("selftests: mptcp: add subflow limits test-cases") Cc: stable@vger.kernel.org Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/323 Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 7 Feb 2023 13:04:16 +0000 (14:04 +0100)]
mptcp: be careful on subflow status propagation on errors
Currently the subflow error report callback unconditionally
propagates the fallback subflow status to the owning msk.
If the msk is already orphaned, the above prevents the code
from correctly tracking the msk moving to the TCP_CLOSE state
and doing the appropriate cleanup.
All the above causes increasing memory usage over time and
sporadic self-tests failures.
There is a great deal of infrastructure trying to propagate
correctly the fallback subflow status to the owning mptcp socket,
e.g. via mptcp_subflow_eof() and subflow_sched_work_if_closed():
in the error propagation path we need only to cope with unorphaned
sockets.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/339 Fixes: 15cc10453398 ("mptcp: deliver ssk errors to msk") Cc: stable@vger.kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 7 Feb 2023 13:04:15 +0000 (14:04 +0100)]
mptcp: fix locking for in-kernel listener creation
For consistency, in mptcp_pm_nl_create_listen_socket(), we need to
call the __mptcp_nmpc_socket() under the msk socket lock.
Note that as a side effect, mptcp_subflow_create_socket() needs a
'nested' lockdep annotation, as it will acquire the subflow (kernel)
socket lock under the in-kernel listener msk socket lock.
The current lack of locking is almost harmless, because the relevant
socket is not exposed to the user space, but in future we will add
more complexity to the mentioned helper, let's play safe.
Fixes: 1729cf186d8a ("mptcp: create the listening socket for new port") Cc: stable@vger.kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 7 Feb 2023 13:04:14 +0000 (14:04 +0100)]
mptcp: fix locking for setsockopt corner-case
We need to call the __mptcp_nmpc_socket(), and later subflow socket
access under the msk socket lock, or e.g. a racing connect() could
change the socket status under the hood, with unexpected results.
Fixes: 54635bd04701 ("mptcp: add TCP_FASTOPEN_CONNECT socket option") Cc: stable@vger.kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 7 Feb 2023 13:04:13 +0000 (14:04 +0100)]
mptcp: do not wait for bare sockets' timeout
If the peer closes all the existing subflows for a given
mptcp socket and later the application closes it, the current
implementation let it survive until the timewait timeout expires.
While the above is allowed by the protocol specification it
consumes resources for almost no reason and additionally
causes sporadic self-tests failures.
Let's move the mptcp socket to the TCP_CLOSE state when there are
no alive subflows at close time, so that the allocated resources
will be freed immediately.
Fixes: e16163b6e2b7 ("mptcp: refactor shutdown and close") Cc: stable@vger.kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 7 Feb 2023 10:30:27 +0000 (12:30 +0200)]
net: ethernet: mtk_eth_soc: fix DSA TX tag hwaccel for switch port 0
Arınç reports that on his MT7621AT Unielec U7621-06 board and MT7623NI
Bananapi BPI-R2, packets received by the CPU over mt7530 switch port 0
(of which this driver acts as the DSA master) are not processed
correctly by software. More precisely, they arrive without a DSA tag
(in packet or in the hwaccel area - skb_metadata_dst()), so DSA cannot
demux them towards the switch's interface for port 0. Traffic from other
ports receives a skb_metadata_dst() with the correct port and is demuxed
properly.
Looking at mtk_poll_rx(), it becomes apparent that this driver uses the
skb vlan hwaccel area:
as a temporary storage for the VLAN hwaccel tag, or the DSA hwaccel tag.
If this is a DSA master it's a DSA hwaccel tag, and finally clears up
the skb VLAN hwaccel header.
I'm guessing that the problem is the (mis)use of API.
skb_vlan_tag_present() looks like this:
So if both vlan_proto and vlan_tci are zeroes, skb_vlan_tag_present()
returns precisely false. I don't know for sure what is the format of the
DSA hwaccel tag, but I surely know that lowermost 3 bits of vlan_proto
are 0 when receiving from port 0:
unsigned int port = vlan_proto & GENMASK(2, 0);
If the RX descriptor has no other bits set to non-zero values in
RX_DMA_VTAG, then the call to __vlan_hwaccel_put_tag() will not, in
fact, make the subsequent skb_vlan_tag_present() return true, because
it's implemented like this:
What we need to do to fix this problem (assuming this is the problem) is
to stop using skb->vlan_all as temporary storage for driver affairs, and
just create some local variables that serve the same purpose, but
hopefully better. Instead of calling skb_vlan_tag_present(), let's look
at a boolean has_hwaccel_tag which we set to true when the RX DMA
descriptors have something. Disambiguate based on netdev_uses_dsa()
whether this is a VLAN or DSA hwaccel tag, and only call
__vlan_hwaccel_put_tag() if we're certain it's a VLAN tag.
Arınç confirms that the treatment works, so this validates the
assumption.
Link: https://lore.kernel.org/netdev/704f3a72-fc9e-714a-db54-272e17612637@arinc9.com/ Fixes: 2d7605a72906 ("net: ethernet: mtk_eth_soc: enable hardware DSA untagging") Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com> Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: David S. Miller <davem@davemloft.net>
Yu Xiao [Tue, 7 Feb 2023 10:16:50 +0000 (11:16 +0100)]
nfp: ethtool: fix the bug of setting unsupported port speed
Unsupported port speed can be set and cause error. Now fixing it
and return an error if setting unsupported speed.
This fix depends on the following, which was included in v6.2-rc1:
commit a61474c41e8c ("nfp: ethtool: support reporting link modes").
Fixes: 7c698737270f ("nfp: add support for .set_link_ksettings()") Signed-off-by: Yu Xiao <yu.xiao@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 26859240e4ee ("txhash: Add socket option to control TX hash rethink behavior") Signed-off-by: Kevin Yang <yyd@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Mon, 6 Feb 2023 20:47:03 +0000 (22:47 +0200)]
net: ethernet: mtk_eth_soc: fix wrong parameters order in __xdp_rxq_info_reg()
Parameters 'queue_index' and 'napi_id' are passed in a swapped order.
Fix it here.
Fixes: 23233e577ef9 ("net: ethernet: mtk_eth_soc: rely on page_pool for single page buffers") Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arınç ÜNAL [Sun, 5 Feb 2023 17:53:31 +0000 (20:53 +0300)]
net: ethernet: mtk_eth_soc: enable special tag when any MAC uses DSA
The special tag is only enabled when the first MAC uses DSA. However, it
must be enabled when any MAC uses DSA. Change the check accordingly.
This fixes hardware DSA untagging not working on the second MAC of the
MT7621 and MT7623 SoCs, and likely other SoCs too. Therefore, remove the
check that disables hardware DSA untagging for the second MAC of the MT7621
and MT7623 SoCs.
Fixes: a1f47752fd62 ("net: ethernet: mtk_eth_soc: disable hardware DSA untagging for second MAC") Co-developed-by: Richard van Schagen <richard@routerhints.com> Signed-off-by: Richard van Schagen <richard@routerhints.com> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 8 Feb 2023 06:04:44 +0000 (22:04 -0800)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-02-06 (ice)
This series contains updates to ice driver only.
Ani removes WQ_MEM_RECLAIM flag from workqueue to resolve
check_flush_dependency warning.
Michal fixes KASAN out-of-bounds warning.
Brett corrects behaviour for port VLAN Rx filters to prevent receiving
of unintended traffic.
Dan Carpenter fixes possible off by one issue.
Zhang Changzhong adjusts error path for switch recipe to prevent memory
leak.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: switch: fix potential memleak in ice_add_adv_recipe()
ice: Fix off by one in ice_tc_forward_to_queue()
ice: Fix disabling Rx VLAN filtering with port VLAN enabled
ice: fix out-of-bounds KASAN warning in virtchnl
ice: Do not use WQ_MEM_RECLAIM flag for workqueue
====================
Sasha Neftin [Mon, 6 Feb 2023 23:58:18 +0000 (15:58 -0800)]
igc: Add ndo_tx_timeout support
On some platforms, 100/1000/2500 speeds seem to have sometimes problems
reporting false positive tx unit hang during stressful UDP traffic. Likely
other Intel drivers introduce responses to a tx hang. Update the 'tx hang'
comparator with the comparison of the head and tail of ring pointers and
restore the tx_timeout_factor to the previous value (one).
This can be test by using netperf or iperf3 applications.
Example:
iperf3 -s -p 5001
iperf3 -c 192.168.0.2 --udp -p 5001 --time 600 -b 0
Haiyang Zhang [Mon, 6 Feb 2023 21:28:49 +0000 (13:28 -0800)]
net: mana: Fix accessing freed irq affinity_hint
After calling irq_set_affinity_and_hint(), the cpumask pointer is
saved in desc->affinity_hint, and will be used later when reading
/proc/irq/<num>/affinity_hint. So the cpumask variable needs to be
persistent. Otherwise, we are accessing freed memory when reading
the affinity_hint file.
Also, need to clear affinity_hint before free_irq(), otherwise there
is a one-time warning and stack trace during module unloading:
To fix the bug, use the persistent mask, cpumask_of(cpu#), and set
affinity_hint to NULL before freeing the IRQ, as required by free_irq().
Cc: stable@vger.kernel.org Fixes: 71fa6887eeca ("net: mana: Assign interrupts to CPUs based on NUMA nodes") Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/1675718929-19565-1-git-send-email-haiyangz@microsoft.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 8 Feb 2023 04:50:30 +0000 (20:50 -0800)]
Merge tag 'linux-can-fixes-for-6.2-20230207' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
can 2023-02-07
The patch is from Devid Antonio Filoni and fixes an address claiming
problem in the J1939 CAN protocol.
* tag 'linux-can-fixes-for-6.2-20230207' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: j1939: do not wait 250 ms if the same addr was already claimed
====================
Shay Drory [Wed, 14 Dec 2022 20:16:23 +0000 (22:16 +0200)]
net/mlx5: Serialize module cleanup with reload and remove
Currently, remove and reload flows can run in parallel to module cleanup.
This design is error prone. For example: aux_drivers callbacks are called
from both cleanup and remove flows with different lockings, which can
cause a deadlock[1].
Hence, serialize module cleanup with reload and remove.
Shay Drory [Wed, 25 Jan 2023 15:39:36 +0000 (17:39 +0200)]
net/mlx5: fw_tracer, Zero consumer index when reloading the tracer
When tracer is reloaded, the device will log the traces at the
beginning of the log buffer. Also, driver is reading the log buffer in
chunks in accordance to the consumer index.
Hence, zero consumer index when reloading the tracer.
Shay Drory [Mon, 9 Jan 2023 13:27:40 +0000 (15:27 +0200)]
net/mlx5: fw_tracer, Clear load bit when freeing string DBs buffers
Whenever the driver is reading the string DBs into buffers, the driver
is setting the load bit, but the driver never clears this bit.
As a result, in case load bit is on and the driver query the device for
new string DBs, the driver won't read again the string DBs.
Fix it by clearing the load bit when query the device for new string
DBs.
Fixes: 2d69356752ff ("net/mlx5: Add support for fw live patch event") Signed-off-by: Shay Drory <shayd@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maher Sanalla [Sun, 22 Jan 2023 21:24:56 +0000 (23:24 +0200)]
net/mlx5: Expose SF firmware pages counter
Currently, each core device has VF pages counter which stores number of
fw pages used by its VFs and SFs.
The current design led to a hang when performing firmware reset on DPU,
where the DPU PFs stalled in sriov unload flow due to waiting on release
of SFs pages instead of waiting on only VFs pages.
Thus, Add a separate counter for SF firmware pages, which will prevent
the stall scenario described above.
Dragos Tatulea [Mon, 23 Jan 2023 14:06:32 +0000 (16:06 +0200)]
net/mlx5e: IPoIB, Show unknown speed instead of error
ethtool is returning an error for unknown speeds for the IPoIB interface:
$ ethtool ib0
netlink error: failed to retrieve link settings
netlink error: Invalid argument
netlink error: failed to retrieve link settings
netlink error: Invalid argument
Settings for ib0:
Link detected: no
After this change, ethtool will return success and show "unknown speed":
$ ethtool ib0
Settings for ib0:
Supported ports: [ ]
Supported link modes: Not reported
Supported pause frame use: No
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Full
Auto-negotiation: off
Port: Other
PHYAD: 0
Transceiver: internal
Link detected: no
Fixes: eb234ee9d541 ("net/mlx5e: IPoIB, Add support for get_link_ksettings in ethtool") Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com> Reviewed-by: Gal Pressman <gal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Amir Tzin [Sun, 8 Jan 2023 13:54:46 +0000 (15:54 +0200)]
net/mlx5e: Fix crash unsetting rx-vlan-filter in switchdev mode
Moving to switchdev mode with rx-vlan-filter on and then setting it off
causes the kernel to crash since fs->vlan is freed during nic profile
cleanup flow.
RX VLAN filtering is not supported in switchdev mode so unset it when
changing to switchdev and restore its value when switching back to
legacy.
Vlad Buslov [Thu, 26 Jan 2023 13:47:12 +0000 (14:47 +0100)]
net/mlx5: Bridge, fix ageing of peer FDB entries
SWITCHDEV_FDB_ADD_TO_BRIDGE event handler that updates FDB entry 'lastuse'
field is only executed for eswitch that owns the entry. However, if peer
entry processed packets at least once it will have hardware counter 'used'
value greater than entry 'lastuse' from that point on, which will cause FDB
entry not being aged out.
net/mlx5: DR, Fix potential race in dr_rule_create_rule_nic
Selecting builder should be protected by the lock to prevent the case
where a new rule sets a builder in the nic_matcher while the previous
rule is still using the nic_matcher.
Fixing this issue and cleaning the error flow.
Fixes: b9b81e1e9382 ("net/mlx5: DR, For short chains of STEs, avoid allocating ste_arr dynamically") Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com> Reviewed-by: Alex Vesker <valex@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Adham Faris [Sun, 8 Jan 2023 16:09:32 +0000 (18:09 +0200)]
net/mlx5e: Update rx ring hw mtu upon each rx-fcs flag change
rq->hw_mtu is used in function en_rx.c/mlx5e_skb_from_cqe_mpwrq_linear()
to catch oversized packets. If FCS is concatenated to the end of the
packet then the check should be updated accordingly.
Rx rings initialization (mlx5e_init_rxq_rq()) invoked for every new set
of channels, as part of mlx5e_safe_switch_params(), unknowingly if it
runs with default configuration or not. Current rq->hw_mtu
initialization assumes default configuration and ignores
params->scatter_fcs_en flag state.
Fix this, by accounting for params->scatter_fcs_en flag state during
rq->hw_mtu initialization.
In addition, updating rq->hw_mtu value during ingress traffic might
lead to packets drop and oversize_pkts_sw_drop counter increase with no
good reason. Hence we remove this optimization and switch the set of
channels with a new one, to make sure we don't get false positives on
the oversize_pkts_sw_drop counter.
Fixes: 102722fc6832 ("net/mlx5e: Add support for RXFCS feature flag") Signed-off-by: Adham Faris <afaris@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
can: j1939: do not wait 250 ms if the same addr was already claimed
The ISO 11783-5 standard, in "4.5.2 - Address claim requirements", states:
d) No CF shall begin, or resume, transmission on the network until 250
ms after it has successfully claimed an address except when
responding to a request for address-claimed.
But "Figure 6" and "Figure 7" in "4.5.4.2 - Address-claim
prioritization" show that the CF begins the transmission after 250 ms
from the first AC (address-claimed) message even if it sends another AC
message during that time window to resolve the address contention with
another CF.
As stated in "4.4.2.3 - Address-claimed message":
In order to successfully claim an address, the CF sending an address
claimed message shall not receive a contending claim from another CF
for at least 250 ms.
As stated in "4.4.3.2 - NAME management (NM) message":
1) A commanding CF can
d) request that a CF with a specified NAME transmit the address-
claimed message with its current NAME.
2) A target CF shall
d) send an address-claimed message in response to a request for a
matching NAME
Taking the above arguments into account, the 250 ms wait is requested
only during network initialization.
Do not restart the timer on AC message if both the NAME and the address
match and so if the address has already been claimed (timer has expired)
or the AC message has been sent to resolve the contention with another
CF (timer is still running).
Signed-off-by: Devid Antonio Filoni <devid.filoni@egluetechnologies.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Link: https://lore.kernel.org/all/20221125170418.34575-1-devid.filoni@egluetechnologies.com Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol") Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jiri Pirko [Mon, 6 Feb 2023 09:41:51 +0000 (10:41 +0100)]
devlink: change port event netdev notifier from per-net to global
Currently only the network namespace of devlink instance is monitored
for port events. If netdev is moved to a different namespace and then
unregistered, NETDEV_PRE_UNINIT is missed which leads to trigger
following WARN_ON in devl_port_unregister().
WARN_ON(devlink_port->type != DEVLINK_PORT_TYPE_NOTSET);
Fix this by changing the netdev notifier from per-net to global so no
event is missed.
Fixes: 02a68a47eade ("net: devlink: track netdev with devlink_port assigned") Signed-off-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20230206094151.2557264-1-jiri@resnulli.us Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Vladimir Oltean [Sun, 5 Feb 2023 19:24:09 +0000 (21:24 +0200)]
selftests: ocelot: tc_flower_chains: make test_vlan_ingress_modify() more comprehensive
We have two IS1 filters of the OCELOT_VCAP_KEY_ANY key type (the one with
"action vlan pop" and the one with "action vlan modify") and one of the
OCELOT_VCAP_KEY_IPV4 key type (the one with "action skbedit priority").
But we have no IS1 filter with the OCELOT_VCAP_KEY_ETYPE key type, and
there was an uncaught breakage there.
To increase test coverage, convert one of the OCELOT_VCAP_KEY_ANY
filters to OCELOT_VCAP_KEY_ETYPE, by making the filter also match on the
MAC SA of the traffic sent by mausezahn, $h1_mac.
Vladimir Oltean [Sun, 5 Feb 2023 19:24:08 +0000 (21:24 +0200)]
net: mscc: ocelot: fix VCAP filters not matching on MAC with "protocol 802.1Q"
Alternative short title: don't instruct the hardware to match on
EtherType with "protocol 802.1Q" flower filters. It doesn't work for the
reasons detailed below.
the created filter is set by ocelot_flower_parse_key() to be of type
OCELOT_VCAP_KEY_ETYPE, and etype is set to {value=0x8100, mask=0xffff}.
This gets propagated all the way to is1_entry_set() which commits it to
hardware (the VCAP_IS1_HK_ETYPE field of the key). Compare this to the
case where src_mac isn't specified - the key type is OCELOT_VCAP_KEY_ANY,
and is1_entry_set() doesn't populate VCAP_IS1_HK_ETYPE.
The problem is that for VLAN-tagged frames, the hardware interprets the
ETYPE field as holding the encapsulated VLAN protocol. So the above
filter will only match those packets which have an encapsulated protocol
of 0x8100, rather than all packets with VLAN ID 200 and the given src_mac.
The reason why this is allowed to occur is because, although we have a
block of code in ocelot_flower_parse_key() which sets "match_protocol"
to false when VLAN keys are present, that code executes too late.
There is another block of code, which executes for Ethernet addresses,
and has a "goto finished_key_parsing" and skips the VLAN header parsing.
By skipping it, "match_protocol" remains with the value it was
initialized with, i.e. "true", and "proto" is set to f->common.protocol,
or 0x8100.
The concept of ignoring some keys rather than erroring out when they are
present but can't be offloaded is dubious in itself, but is present
since the initial commit fe3490e6107e ("net: mscc: ocelot: Hardware
ofload for tc flower filter"), and it's outside of the scope of this
patch to change that.
The problem was introduced when the driver started to interpret the
flower filter's protocol, and populate the VCAP filter's ETYPE field
based on it.
To fix this, it is sufficient to move the code that parses the VLAN keys
earlier than the "goto finished_key_parsing" instruction. This will
ensure that if we have a flower filter with both VLAN and Ethernet
address keys, it won't match on ETYPE 0x8100, because the VLAN key
parsing sets "match_protocol = false".
Fixes: 86b956de119c ("net: mscc: ocelot: support matching on EtherType") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230205192409.1796428-1-vladimir.oltean@nxp.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Vladimir Oltean [Sun, 5 Feb 2023 14:07:13 +0000 (16:07 +0200)]
net: dsa: mt7530: don't change PVC_EG_TAG when CPU port becomes VLAN-aware
Frank reports that in a mt7530 setup where some ports are standalone and
some are in a VLAN-aware bridge, 8021q uppers of the standalone ports
lose their VLAN tag on xmit, as seen by the link partner.
This seems to occur because once the other ports join the VLAN-aware
bridge, mt7530_port_vlan_filtering() also calls
mt7530_port_set_vlan_aware(ds, cpu_dp->index), and this affects the way
that the switch processes the traffic of the standalone port.
Relevant is the PVC_EG_TAG bit. The MT7530 documentation says about it:
EG_TAG: Incoming Port Egress Tag VLAN Attribution
0: disabled (system default)
1: consistent (keep the original ingress tag attribute)
My interpretation is that this setting applies on the ingress port, and
"disabled" is basically the normal behavior, where the egress tag format
of the packet (tagged or untagged) is decided by the VLAN table
(MT7530_VLAN_EGRESS_UNTAG or MT7530_VLAN_EGRESS_TAG).
But there is also an option of overriding the system default behavior,
and for the egress tagging format of packets to be decided not by the
VLAN table, but simply by copying the ingress tag format (if ingress was
tagged, egress is tagged; if ingress was untagged, egress is untagged;
aka "consistent). This is useful in 2 scenarios:
- VLAN-unaware bridge ports will always encounter a miss in the VLAN
table. They should forward a packet as-is, though. So we use
"consistent" there. See commit e045124e9399 ("net: dsa: mt7530: fix
tagged frames pass-through in VLAN-unaware mode").
- Traffic injected from the CPU port. The operating system is in god
mode; if it wants a packet to exit as VLAN-tagged, it sends it as
VLAN-tagged. Otherwise it sends it as VLAN-untagged*.
*This is true only if we don't consider the bridge TX forwarding offload
feature, which mt7530 doesn't support.
So for now, make the CPU port always stay in "consistent" mode to allow
software VLANs to be forwarded to their egress ports with the VLAN tag
intact, and not stripped.
Dan Carpenter [Fri, 28 Oct 2022 15:02:24 +0000 (18:02 +0300)]
ice: Fix off by one in ice_tc_forward_to_queue()
The > comparison should be >= to prevent reading one element beyond
the end of the array.
The "vsi->num_rxq" is not strictly speaking the number of elements in
the vsi->rxq_map[] array. The array has "vsi->alloc_rxq" elements and
"vsi->num_rxq" is less than or equal to the number of elements in the
array. The array is allocated in ice_vsi_alloc_arrays(). It's still
an off by one but it might not access outside the end of the array.
Fixes: 143b86f346c7 ("ice: Enable RX queue selection using skbedit action") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Brett Creeley [Mon, 16 Jan 2023 12:34:58 +0000 (13:34 +0100)]
ice: Fix disabling Rx VLAN filtering with port VLAN enabled
If the user turns on the vf-true-promiscuous-support flag, then Rx VLAN
filtering will be disabled if the VF requests to enable promiscuous
mode. When the VF is in a port VLAN, this is the incorrect behavior
because it will allow the VF to receive traffic outside of its port VLAN
domain. Fortunately this only resulted in the VF(s) receiving broadcast
traffic outside of the VLAN domain because all of the VLAN promiscuous
rules are based on the port VLAN ID. Fix this by setting the
.disable_rx_filtering VLAN op to a no-op when a port VLAN is enabled on
the VF.
Also, make sure to make this fix for both Single VLAN Mode and Double
VLAN Mode enabled devices.
Fixes: c31af68a1b94 ("ice: Add outer_vlan_ops and VSI specific VLAN ops implementations") Signed-off-by: Brett Creeley <brett.creeley@intel.com> Signed-off-by: Karen Ostrowska <karen.ostrowska@intel.com> Tested-by: Marek Szlosek <marek.szlosek@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ICE_AQ_LINK_SPEED_UNKNOWN define is BIT(15). The value is bigger
than both legacy and normal link speed tables. Add one element (0 -
unknown) to both tables. There is no need to explicitly set table size,
leave it empty.
Fixes: 1d0e28a9be1f ("ice: Remove and replace ice speed defines with ethtool.h versions") Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
When both ice and the irdma driver are loaded, a warning in
check_flush_dependency is being triggered. This is due to ice driver
workqueue being allocated with the WQ_MEM_RECLAIM flag and the irdma one
is not.
According to kernel documentation, this flag should be set if the
workqueue will be involved in the kernel's memory reclamation flow.
Since it is not, there is no need for the ice driver's WQ to have this
flag set so remove it.
Alan Stern [Fri, 3 Feb 2023 19:32:09 +0000 (14:32 -0500)]
net: USB: Fix wrong-direction WARNING in plusb.c
The syzbot fuzzer detected a bug in the plusb network driver: A
zero-length control-OUT transfer was treated as a read instead of a
write. In modern kernels this error provokes a WARNING:
The fix is to call usbnet_write_cmd() instead of usbnet_read_cmd() and
remove the USB_DIR_IN flag.
Reported-and-tested-by: syzbot+2a0e7abd24f1eb90ce25@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Fixes: 090ffa9d0e90 ("[PATCH] USB: usbnet (9/9) module for pl2301/2302 cables") CC: stable@vger.kernel.org Link: https://lore.kernel.org/r/00000000000052099f05f3b3e298@google.com/ Signed-off-by: David S. Miller <davem@davemloft.net>
net: microchip: sparx5: fix PTP init/deinit not checking all ports
Check all ports instead of just port_count ports. PTP init was only
checking ports 0 to port_count. If the hardware ports are not mapped
starting from 0 then they would be missed, e.g. if only ports 20-30 were
mapped it would attempt to init ports 0-10, resulting in NULL pointers
when attempting to timestamp. Now it will init all mapped ports.
Fixes: 70dfe25cd866 ("net: sparx5: Update extraction/injection for timestamping") Signed-off-by: Casper Andersson <casper.casan@gmail.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
uapi: add missing ip/ipv6 header dependencies for linux/stddef.h
Since commit 58e0be1ef6118 ("net: use struct_group to copy ip/ipv6
header addresses"), ip and ipv6 headers started to use the __struct_group
definition, which is defined at include/uapi/linux/stddef.h. However,
linux/stddef.h isn't explicitly included in include/uapi/linux/{ip,ipv6}.h,
which breaks build of xskxceiver bpf selftest if you install the uapi
headers in the system:
$ make V=1 xskxceiver -C tools/testing/selftests/bpf
...
make: Entering directory '(...)/tools/testing/selftests/bpf'
gcc -g -O0 -rdynamic -Wall -Werror (...)
In file included from xskxceiver.c:79:
/usr/include/linux/ip.h:103:9: error: expected specifier-qualifier-list before ‘__struct_group’
103 | __struct_group(/* no tag */, addrs, /* no attrs */,
| ^~~~~~~~~~~~~~
...
Include the missing <linux/stddef.h> dependency in ip.h and do the
same for the ipv6.h header.
Fixes: 58e0be1ef611 ("net: use struct_group to copy ip/ipv6 header addresses") Signed-off-by: Herton R. Krzesinski <herton@redhat.com> Reviewed-by: Carlos O'Donell <carlos@redhat.com> Tested-by: Carlos O'Donell <carlos@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
neigh: make sure used and confirmed times are valid
Entries can linger in cache without timer for days, thanks to
the gc_thresh1 limit. As result, without traffic, the confirmed
time can be outdated and to appear to be in the future. Later,
on traffic, NUD_STALE entries can switch to NUD_DELAY and start
the timer which can see the invalid confirmed time and wrongly
switch to NUD_REACHABLE state instead of NUD_PROBE. As result,
timer is set many days in the future. This is more visible on
32-bit platforms, with higher HZ value.
Why this is a problem? While we expect unused entries to expire,
such entries stay in REACHABLE state for too long, locked in
cache. They are not expired normally, only when cache is full.
Problem and the wrong state change reported by Zhang Changzhong:
172.16.1.18 dev bond0 lladdr 0a:0e:0f:01:12:01 ref 1 used 350521/15994171/350520 probes 4 REACHABLE
350520 seconds have elapsed since this entry was last updated, but it is
still in the REACHABLE state (base_reachable_time_ms is 30000),
preventing lladdr from being updated through probe.
Fix it by ensuring timer is started with valid used/confirmed
times. Considering the valid time range is LONG_MAX jiffies,
we try not to go too much in the past while we are in
DELAY/PROBE state. There are also places that need
used/updated times to be validated while timer is not running.
Reported-by: Zhang Changzhong <zhangchangzhong@huawei.com> Signed-off-by: Julian Anastasov <ja@ssi.bg> Tested-by: Zhang Changzhong <zhangchangzhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allen Hubbe [Thu, 2 Feb 2023 21:55:37 +0000 (13:55 -0800)]
ionic: missed doorbell workaround
In one version of the HW there is a remote possibility that it
will miss the doorbell ring. This adds a bit of protection to
be sure we don't stall a queue from a missed doorbell.
Fixes: 0f3154e6bcb3 ("ionic: Add Tx and Rx handling") Signed-off-by: Allen Hubbe <allen.hubbe@amd.com> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Shannon Nelson [Thu, 2 Feb 2023 21:55:36 +0000 (13:55 -0800)]
ionic: clear up notifyq alloc commentary
Make sure the q+cq alloc for NotifyQ is clearly documented
and don't bother with unnecessary local variables.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Neel Patel [Thu, 2 Feb 2023 21:55:35 +0000 (13:55 -0800)]
ionic: clean interrupt before enabling queue to avoid credit race
Clear the interrupt credits before enabling the queue rather
than after to be sure that the enabled queue starts at 0 and
that we don't wipe away possible credits after enabling the
queue.
Fixes: 0f3154e6bcb3 ("ionic: Add Tx and Rx handling") Signed-off-by: Neel Patel <neel.patel@amd.com> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiner Kallweit [Thu, 2 Feb 2023 20:45:36 +0000 (21:45 +0100)]
net: phy: meson-gxl: use MMD access dummy stubs for GXL, internal PHY
Jerome provided the information that also the GXL internal PHY doesn't
support MMD register access and EEE. MMD reads return 0xffff, what
results in e.g. completely wrong ethtool --show-eee output.
Therefore use the MMD dummy stubs.
Fixes: d853d145ea3e ("net: phy: add an option to disable EEE advertisement") Suggested-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Link: https://lore.kernel.org/r/84432fe4-0be4-bc82-4e5c-557206b40f56@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: macb: Perform zynqmp dynamic configuration only for SGMII interface
In zynqmp platforms where firmware supports dynamic SGMII configuration
but has other non-SGMII ethernet devices, it fails them with no packets
received at the RX interface.
To fix this behaviour perform SGMII dynamic configuration only
for the SGMII phy interface.
Qi Zheng [Thu, 2 Feb 2023 09:32:55 +0000 (17:32 +0800)]
bonding: fix error checking in bond_debug_reregister()
Since commit ff9fb72bc077 ("debugfs: return error values,
not NULL") changed return value of debugfs_rename() in
error cases from %NULL to %ERR_PTR(-ERROR), we should
also check error values instead of NULL.
Clément Léger [Tue, 31 Jan 2023 10:02:42 +0000 (11:02 +0100)]
net: phylink: move phy_device_free() to correctly release phy device
After calling fwnode_phy_find_device(), the phy device refcount is
incremented. Then, when the phy device is attached to a netdev with
phy_attach_direct(), the refcount is also incremented but only
decremented in the caller if phy_attach_direct() fails. Move
phy_device_free() before the "if" to always release it correctly.
Indeed, either phy_attach_direct() failed and we don't want to keep a
reference to the phydev or it succeeded and a reference has been taken
internally.
Fixes: 25396f680dd6 ("net: phylink: introduce phylink_fwnode_phy_connect()") Signed-off-by: Clément Léger <clement.leger@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 2 Feb 2023 22:03:31 +0000 (14:03 -0800)]
Merge tag 'net-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf, can and netfilter.
Current release - regressions:
- phy: fix null-deref in phy_attach_direct
- mac802154: fix possible double free upon parsing error
Previous releases - regressions:
- bpf: preserve reg parent/live fields when copying range info,
prevent mis-verification of programs as safe
- ip6: fix GRE tunnels not generating IPv6 link local addresses
- phy: dp83822: fix null-deref on DP83825/DP83826 devices
- sctp: do not check hb_timer.expires when resetting hb_timer
- eth: mtk_sock: fix SGMII configuration after phylink conversion
Previous releases - always broken:
- eth: xdp: execute xdp_do_flush() before napi_complete_done()
- skb: do not mix page pool and page referenced frags in GRO
- bpf:
- fix a possible task gone issue with bpf_send_signal[_thread]()
- fix an off-by-one bug in bpf_mem_cache_idx() to select the right
cache
- add missing btf_put to register_btf_id_dtor_kfuncs
- sockmap: fon't let sock_map_{close,destroy,unhash} call itself
- gso: fix null-deref in skb_segment_list()
- mctp: purge receive queues on sk destruction
- fix UaF caused by accept on already connected socket in exotic
socket families
- tls: don't treat list head as an entry in tls_is_tx_ready()
- netfilter: br_netfilter: disable sabotage_in hook after first
suppression
- wwan: t7xx: fix runtime PM implementation
Misc:
- MAINTAINERS: spring cleanup of networking maintainers"
* tag 'net-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
mtk_sgmii: enable PCS polling to allow SFP work
net: mediatek: sgmii: fix duplex configuration
net: mediatek: sgmii: ensure the SGMII PHY is powered down on configuration
MAINTAINERS: update SCTP maintainers
MAINTAINERS: ipv6: retire Hideaki Yoshifuji
mailmap: add John Crispin's entry
MAINTAINERS: bonding: move Veaceslav Falico to CREDITS
net: openvswitch: fix flow memory leak in ovs_flow_cmd_new
net: ethernet: mtk_eth_soc: disable hardware DSA untagging for second MAC
virtio-net: Keep stop() to follow mirror sequence of open()
selftests: net: udpgso_bench_tx: Cater for pending datagrams zerocopy benchmarking
selftests: net: udpgso_bench: Fix racing bug between the rx/tx programs
selftests: net: udpgso_bench_rx/tx: Stop when wrong CLI args are provided
selftests: net: udpgso_bench_rx: Fix 'used uninitialized' compiler warning
can: mcp251xfd: mcp251xfd_ring_set_ringparam(): assign missing tx_obj_num_coalesce_irq
can: isotp: split tx timer into transmission and timeout
can: isotp: handle wait_event_interruptible() return values
can: raw: fix CAN FD frame transmissions over CAN XL devices
can: j1939: fix errant WARN_ON_ONCE in j1939_session_deactivate
hv_netvsc: Fix missed pagebuf entries in netvsc_dma_map/unmap()
...
Linus Torvalds [Thu, 2 Feb 2023 21:08:18 +0000 (13:08 -0800)]
Merge tag 'linux-kselftest-kunit-fixes-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit fixes from Shuah Khan:
"Three fixes to bugs that cause kernel crash, link error during build,
and a third to fix kunit_test_init_section_suites() extra indirection
issue"
* tag 'linux-kselftest-kunit-fixes-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: fix kunit_test_init_section_suites(...)
kunit: fix bug in KUNIT_EXPECT_MEMEQ
kunit: Export kunit_running()
Linus Torvalds [Thu, 2 Feb 2023 21:02:45 +0000 (13:02 -0800)]
Merge tag 'soc-fixes-6.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"The majority of bugfixes is once more for the NXP i.MX platform,
addressing issue with i.MX8M (UART, watchdog and ethernet) as well as
imx8dxl power button and the USB modem on an imx7 board.
The reason that i.MX always shows up here is obviously not that they
are more buggy than the others, but they have the most boards and are
good about getting fixes in quickly.
The other DT fixes are for the Nuvoton wpcm450 flash controller and
the i2c mux on an ASpeed board.
Lastly, there are updates to the MAINTAINERS entries for Mediatek,
AMD/Seattle and NXP SoCs, as well as a lone code fix for error
handling in the allwinner 'rsb' bus driver"
* tag 'soc-fixes-6.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: wpcm450: Add nuvoton,shm = <&shm> to FIU node
MAINTAINERS: Update entry for MediaTek SoC support
MAINTAINERS: amd: drop inactive Brijesh Singh
ARM: dts: imx7d-smegw01: Fix USB host over-current polarity
arm64: dts: imx8mm-verdin: Do not power down eth-phy
MAINTAINERS: match freescale ARM64 DT directory in i.MX entry
arm64: dts: imx8mm: Fix pad control for UART1_DTE_RX
ARM: dts: aspeed: Fix pca9849 compatible
arm64: dts: freescale: imx8dxl: fix sc_pwrkey's property name linux,keycode
arm64: dts: imx8m-venice: Remove incorrect 'uart-has-rtscts'
arm64: dts: imx8mm: Reinstate GPIO watchdog always-running property on eDM SBC
bus: sunxi-rsb: Fix error handling in sunxi_rsb_init()
Linus Torvalds [Thu, 2 Feb 2023 20:52:47 +0000 (12:52 -0800)]
Merge tag 's390-6.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Heiko Carstens:
- With CONFIG_VMAP_STACK enabled it is not possible to load the s390
specific diag288_wdt watchdog module. The reason is that a pointer to
a string is passed to an inline assembly; this string however is
located on the stack, while the instruction within the inline
assembly expects a physicial address. Fix this by copying the string
to a kmalloc'ed buffer.
- The diag288_wdt watchdog module does not indicate that it accesses
memory from an inline assembly, which it does. Add "memory" to the
clobber list to prevent the compiler from optimizing code incorrectly
away.
- Pass size of the uncompressed kernel image to __decompress() call.
Otherwise the kernel image decompressor may corrupt/overwrite an
initrd. This was reported to happen on s390 after commit 2aa14b1ab2c4
("zstd: import usptream v1.5.2").
* tag 's390-6.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/decompressor: specify __decompress() buf len to avoid overflow
watchdog: diag288_wdt: fix __diag288() inline assembly
watchdog: diag288_wdt: do not use stack buffers for hardware data
Linus Torvalds [Thu, 2 Feb 2023 20:47:08 +0000 (12:47 -0800)]
Merge tag 'platform-drivers-x86-v6.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"A set of AMD PMF fixes + a few other small fixes"
* tag 'platform-drivers-x86-v6.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: touchscreen_dmi: Add Chuwi Vi8 (CWI501) DMI match
platform/x86: thinkpad_acpi: Fix thinklight LED brightness returning 255
platform/x86/amd: pmc: add CONFIG_SERIO dependency
platform/x86/amd/pmf: Ensure mutexes are initialized before use
platform/x86/amd/pmf: Fix to update SPS thermals when power supply change
platform/x86/amd/pmf: Fix to update SPS default pprof thermals
platform/x86/amd/pmf: update to auto-mode limits only after AMT event
platform/x86/amd/pmf: Add helper routine to check pprof is balanced
platform/x86/amd/pmf: Add helper routine to update SPS thermals
Bjørn Mork [Wed, 1 Feb 2023 18:23:30 +0000 (19:23 +0100)]
net: mediatek: sgmii: fix duplex configuration
The logic of the duplex bit is inverted. Setting it means half
duplex, not full duplex.
Fix and rename macro to avoid confusion.
Fixes: 7e538372694b ("net: ethernet: mediatek: Re-add support SGMII") Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Bjørn Mork <bjorn@mork.no> Acked-by: Daniel Golle <daniel@makrotopia.org> Tested-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: mediatek: sgmii: ensure the SGMII PHY is powered down on configuration
The code expect the PHY to be in power down which is only true after reset.
Allow changes of the SGMII parameters more than once.
Only power down when reconfiguring to avoid bouncing the link when there's
no reason to - based on code from Russell King.
There are cases when the SGMII_PHYA_PWD register contains 0x9 which
prevents SGMII from working. The SGMII still shows link but no traffic
can flow. Writing 0x0 to the PHYA_PWD register fix the issue. 0x0 was
taken from a good working state of the SGMII interface.
Fixes: 42c03844e93d ("net-next: mediatek: add support for MediaTek MT7622 SoC") Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk> Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
[ bmork: rebased and squashed into one patch ] Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Bjørn Mork <bjorn@mork.no> Acked-by: Daniel Golle <daniel@makrotopia.org> Tested-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 2 Feb 2023 19:51:24 +0000 (11:51 -0800)]
Merge tag 'linux-can-fixes-for-6.2-20230202' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
can 2023-02-02
The first patch is by Ziyang Xuan and removes a errant WARN_ON_ONCE()
in the CAN J1939 protocol.
The next 3 patches are by Oliver Hartkopp. The first 2 target the CAN
ISO-TP protocol and fix the state machine with respect to signals and
a regression found by the syzbot.
The last patch is by me an missing assignment during the ethtool ring
configuration callback.
* tag 'linux-can-fixes-for-6.2-20230202' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: mcp251xfd: mcp251xfd_ring_set_ringparam(): assign missing tx_obj_num_coalesce_irq
can: isotp: split tx timer into transmission and timeout
can: isotp: handle wait_event_interruptible() return values
can: raw: fix CAN FD frame transmissions over CAN XL devices
can: j1939: fix errant WARN_ON_ONCE in j1939_session_deactivate
====================
====================
MAINTAINERS: spring refresh of networking maintainers
Use Jon Corbet's script for generating statistics about maintainer
coverage to identify inactive maintainers of relatively active code.
Move them to CREDITS.
====================
Arınç ÜNAL [Sat, 28 Jan 2023 09:42:32 +0000 (12:42 +0300)]
net: ethernet: mtk_eth_soc: disable hardware DSA untagging for second MAC
According to my tests on MT7621AT and MT7623NI SoCs, hardware DSA untagging
won't work on the second MAC. Therefore, disable this feature when the
second MAC of the MT7621 and MT7623 SoCs is being used.
Andrei Gherzan [Wed, 1 Feb 2023 00:16:16 +0000 (00:16 +0000)]
selftests: net: udpgso_bench_tx: Cater for pending datagrams zerocopy benchmarking
The test tool can check that the zerocopy number of completions value is
valid taking into consideration the number of datagram send calls. This can
catch the system into a state where the datagrams are still in the system
(for example in a qdisk, waiting for the network interface to return a
completion notification, etc).
This change adds a retry logic of computing the number of completions up to
a configurable (via CLI) timeout (default: 2 seconds).
Fixes: 79ebc3c26010 ("net/udpgso_bench_tx: options to exercise TX CMSG") Signed-off-by: Andrei Gherzan <andrei.gherzan@canonical.com> Cc: Willem de Bruijn <willemb@google.com> Cc: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/20230201001612.515730-4-andrei.gherzan@canonical.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Andrei Gherzan [Wed, 1 Feb 2023 00:16:14 +0000 (00:16 +0000)]
selftests: net: udpgso_bench: Fix racing bug between the rx/tx programs
"udpgro_bench.sh" invokes udpgso_bench_rx/udpgso_bench_tx programs
subsequently and while doing so, there is a chance that the rx one is not
ready to accept socket connections. This racing bug could fail the test
with at least one of the following:
This change addresses this by making udpgro_bench.sh wait for the rx
program to be ready before firing off the tx one - up to a 10s timeout.
Fixes: 3a687bef148d ("selftests: udp gso benchmark") Signed-off-by: Andrei Gherzan <andrei.gherzan@canonical.com> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Willem de Bruijn <willemb@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/20230201001612.515730-3-andrei.gherzan@canonical.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Andrei Gherzan [Wed, 1 Feb 2023 00:16:12 +0000 (00:16 +0000)]
selftests: net: udpgso_bench_rx/tx: Stop when wrong CLI args are provided
Leaving unrecognized arguments buried in the output, can easily hide a
CLI/script typo. Avoid this by exiting when wrong arguments are provided to
the udpgso_bench test programs.
Fixes: 3a687bef148d ("selftests: udp gso benchmark") Signed-off-by: Andrei Gherzan <andrei.gherzan@canonical.com> Cc: Willem de Bruijn <willemb@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/20230201001612.515730-2-andrei.gherzan@canonical.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
/usr/include/x86_64-linux-gnu/bits/error.h:40:5: warning: ‘gso_size’ may
be used uninitialized [-Wmaybe-uninitialized]
40 | __error_noreturn (__status, __errnum, __format,
__va_arg_pack ());
|
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
udpgso_bench_rx.c: In function ‘main’:
udpgso_bench_rx.c:253:23: note: ‘gso_size’ was declared here
253 | int ret, len, gso_size, budget = 256;
If the a new ring layout is set, the max coalesced frames for RX and
TX are re-calculated, too. Add the missing assignment of the newly
calculated TX max coalesced frames.
Oliver Hartkopp [Wed, 4 Jan 2023 14:57:01 +0000 (15:57 +0100)]
can: isotp: split tx timer into transmission and timeout
The timer for the transmission of isotp PDUs formerly had two functions:
1. send two consecutive frames with a given time gap
2. monitor the timeouts for flow control frames and the echo frames
This led to larger txstate checks and potentially to a problem discovered
by syzbot which enabled the panic_on_warn feature while testing.
The former 'txtimer' function is split into 'txfrtimer' and 'txtimer'
to handle the two above functionalities with separate timer callbacks.
The two simplified timers now run in one-shot mode and make the state
transitions (especially with isotp_rcv_echo) better understandable.
Fixes: 866337865f37 ("can: isotp: fix tx state handling for echo tx processing") Reported-by: syzbot+5aed6c3aaba661f5b917@syzkaller.appspotmail.com Cc: stable@vger.kernel.org # >= v6.0 Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Link: https://lore.kernel.org/all/20230104145701.2422-1-socketcan@hartkopp.net Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When wait_event_interruptible() has been interrupted by a signal the
tx.state value might not be ISOTP_IDLE. Force the state machines
into idle state to inhibit the timer handlers to continue working.
Fixes: 866337865f37 ("can: isotp: fix tx state handling for echo tx processing") Cc: stable@vger.kernel.org Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Link: https://lore.kernel.org/all/20230112192347.1944-1-socketcan@hartkopp.net Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oliver Hartkopp [Tue, 31 Jan 2023 10:56:13 +0000 (11:56 +0100)]
can: raw: fix CAN FD frame transmissions over CAN XL devices
A CAN XL device is always capable to process CAN FD frames. The former
check when sending CAN FD frames relied on the existence of a CAN FD
device and did not check for a CAN XL device that would be correct
too.
With this patch the CAN FD feature is enabled automatically when CAN
XL is switched on - and CAN FD cannot be switch off while CAN XL is
enabled.
This precondition also leads to a clean up and reduction of checks in
the hot path in raw_rcv() and raw_sendmsg(). Some conditions are
reordered to handle simple checks first.
changes since v1: https://lore.kernel.org/all/20230131091012.50553-1-socketcan@hartkopp.net
- fixed typo: devive -> device
changes since v2: https://lore.kernel.org/all/20230131091824.51026-1-socketcan@hartkopp.net/
- reorder checks in if statements to handle simple checks first
Ziyang Xuan [Mon, 6 Sep 2021 09:42:00 +0000 (17:42 +0800)]
can: j1939: fix errant WARN_ON_ONCE in j1939_session_deactivate
The conclusion "j1939_session_deactivate() should be called with a
session ref-count of at least 2" is incorrect. In some concurrent
scenarios, j1939_session_deactivate can be called with the session
ref-count less than 2. But there is not any problem because it
will check the session active state before session putting in
j1939_session_deactivate_locked().
Here is the concurrent scenario of the problem reported by syzbot
and my reproduction log.
Michael Kelley [Tue, 31 Jan 2023 03:33:06 +0000 (19:33 -0800)]
hv_netvsc: Fix missed pagebuf entries in netvsc_dma_map/unmap()
netvsc_dma_map() and netvsc_dma_unmap() currently check the cp_partial
flag and adjust the page_count so that pagebuf entries for the RNDIS
portion of the message are skipped when it has already been copied into
a send buffer. But this adjustment has already been made by code in
netvsc_send(). The duplicate adjustment causes some pagebuf entries to
not be mapped. In a normal VM, this doesn't break anything because the
mapping doesn’t change the PFN. But in a Confidential VM,
dma_map_single() does bounce buffering and provides a different PFN.
Failing to do the mapping causes the wrong PFN to be passed to Hyper-V,
and various errors ensue.
Fix this by removing the duplicate adjustment in netvsc_dma_map() and
netvsc_dma_unmap().
Fixes: 846da38de0e8 ("net: netvsc: Add Isolation VM support for netvsc driver") Cc: stable@vger.kernel.org Signed-off-by: Michael Kelley <mikelley@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Link: https://lore.kernel.org/r/1675135986-254490-1-git-send-email-mikelley@microsoft.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tom Rix [Tue, 31 Jan 2023 21:54:37 +0000 (13:54 -0800)]
igc: return an error if the mac type is unknown in igc_ptp_systim_to_hwtstamp()
clang static analysis reports
drivers/net/ethernet/intel/igc/igc_ptp.c:673:3: warning: The left operand of
'+' is a garbage value [core.UndefinedBinaryOperatorResult]
ktime_add_ns(shhwtstamps.hwtstamp, adjust);
^ ~~~~~~~~~~~~~~~~~~~~
igc_ptp_systim_to_hwtstamp() silently returns without setting the hwtstamp
if the mac type is unknown. This should be treated as an error.
Fixes: 81b055205e8b ("igc: Add support for RX timestamping") Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Acked-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20230131215437.1528994-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yanguo Li [Tue, 31 Jan 2023 08:03:13 +0000 (09:03 +0100)]
nfp: flower: avoid taking mutex in atomic context
A mutex may sleep, which is not permitted in atomic context.
Avoid a case where this may arise by moving the to
nfp_flower_lag_get_info_from_netdev() in nfp_tun_write_neigh() spinlock.
Fixes: abc210952af7 ("nfp: flower: tunnel neigh support bond offload") Reported-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Yanguo Li <yanguo.li@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230131080313.2076060-1-simon.horman@corigine.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
ip/ip6_gre: Fix GRE tunnels not generating IPv6 link local addresses
For our point-to-point GRE tunnels, they have IN6_ADDR_GEN_MODE_NONE
when they are created then we set IN6_ADDR_GEN_MODE_EUI64 when they
come up to generate the IPv6 link local address for the interface.
Recently we found that they were no longer generating IPv6 addresses.
Also, non-point-to-point tunnels were not generating any IPv6 link
local address and instead generating an IPv6 compat address,
breaking IPv6 communication on the tunnel.
These failures were caused by commit e5dd729460ca and this patch set
aims to resolve these issues.
====================
Thomas Winter [Tue, 31 Jan 2023 03:46:46 +0000 (16:46 +1300)]
ip/ip6_gre: Fix non-point-to-point tunnel not generating IPv6 link local address
We recently found that our non-point-to-point tunnels were not
generating any IPv6 link local address and instead generating an
IPv6 compat address, breaking IPv6 communication on the tunnel.
Previously, addrconf_gre_config always would call addrconf_addr_gen
and generate a EUI64 link local address for the tunnel.
Then commit e5dd729460ca changed the code path so that add_v4_addrs
is called but this only generates a compat IPv6 address for
non-point-to-point tunnels.
I assume the compat address is specifically for SIT tunnels so
have kept that only for SIT - GRE tunnels now always generate link
local addresses.
Fixes: e5dd729460ca ("ip/ip6_gre: use the same logic as SIT interfaces when computing v6LL address") Signed-off-by: Thomas Winter <Thomas.Winter@alliedtelesis.co.nz> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Thomas Winter [Tue, 31 Jan 2023 03:46:45 +0000 (16:46 +1300)]
ip/ip6_gre: Fix changing addr gen mode not generating IPv6 link local address
For our point-to-point GRE tunnels, they have IN6_ADDR_GEN_MODE_NONE
when they are created then we set IN6_ADDR_GEN_MODE_EUI64 when they
come up to generate the IPv6 link local address for the interface.
Recently we found that they were no longer generating IPv6 addresses.
This issue would also have affected SIT tunnels.
Commit e5dd729460ca changed the code path so that GRE tunnels
generate an IPv6 address based on the tunnel source address.
It also changed the code path so GRE tunnels don't call addrconf_addr_gen
in addrconf_dev_config which is called by addrconf_sysctl_addr_gen_mode
when the IN6_ADDR_GEN_MODE is changed.
This patch aims to fix this issue by moving the code in addrconf_notify
which calls the addr gen for GRE and SIT into a separate function
and calling it in the places that expect the IPv6 address to be
generated.
The previous addrconf_dev_config is renamed to addrconf_eth_config
since it only expected eth type interfaces and follows the
addrconf_gre/sit_config format.
A part of this changes means that the loopback address will be
attempted to be configured when changing addr_gen_mode for lo.
This should not be a problem because the address should exist anyway
and if does already exist then no error is produced.
Fixes: e5dd729460ca ("ip/ip6_gre: use the same logic as SIT interfaces when computing v6LL address") Signed-off-by: Thomas Winter <Thomas.Winter@alliedtelesis.co.nz> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Wed, 1 Feb 2023 18:31:53 +0000 (10:31 -0800)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"Just small bugfixes all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa: ifcvf: Do proper cleanup if IFCVF init fails
vhost-scsi: unbreak any layout for response
tools/virtio: fix the vringh test for virtio ring changes
vhost/net: Clear the pending messages when the backend is removed
Linus Torvalds [Wed, 1 Feb 2023 18:26:23 +0000 (10:26 -0800)]
Merge tag 'sound-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A bit higher volume of changes than wished, but each change is
relatively small and the fix targets are mostly device-specific, so
those should be safe as a late stage merge.
The most significant LoC is about the memalloc helper fix, which is
applied only to Xen PV. The other major parts are ASoC Intel SOF and
AVS fixes that are scattered as various small code changes. The rest
are device-specific fixes and quirks for HD- and USB-audio, FireWire
and ASoC AMD / HDMI"
* tag 'sound-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (30 commits)
ALSA: firewire-motu: fix unreleased lock warning in hwdep device
ALSA: memalloc: Workaround for Xen PV
ASoC: cs42l56: fix DT probe
ASoC: codecs: wsa883x: correct playback min/max rates
ALSA: hda/realtek: Add Acer Predator PH315-54
ASoC: amd: yc: Add Xiaomi Redmi Book Pro 15 2022 into DMI table
ALSA: hda: Do not unset preset when cleaning up codec
ASoC: SOF: sof-audio: prepare_widgets: Check swidget for NULL on sink failure
ASoC: hdmi-codec: zero clear HDMI pdata
ASoC: SOF: ipc4-mtrace: prevent underflow in sof_ipc4_priority_mask_dfs_write()
ASoC: Intel: sof_ssp_amp: always set dpcm_capture for amplifiers
ASoC: Intel: sof_nau8825: always set dpcm_capture for amplifiers
ASoC: Intel: sof_cs42l42: always set dpcm_capture for amplifiers
ASoC: Intel: sof_rt5682: always set dpcm_capture for amplifiers
ALSA: hda/via: Avoid potential array out-of-bound in add_secret_dac_path()
ALSA: usb-audio: Add FIXED_RATE quirk for JBL Quantum610 Wireless
ALSA: hda/realtek: fix mute/micmute LEDs, speaker don't work for a HP platform
ASoC: SOF: keep prepare/unprepare widgets in sink path
ASoC: SOF: sof-audio: skip prepare/unprepare if swidget is NULL
ASoC: SOF: sof-audio: unprepare when swidget->use_count > 0
...
ARM: dts: wpcm450: Add nuvoton,shm = <&shm> to FIU node
The Flash Interface Unit (FIU) should have a reference to the Shared
Memory controller (SHM) so that flash access from the host (x86 computer
managed by the WPCM450 BMC) can be blocked during flash access by the
FIU driver.
MAINTAINERS: Update entry for MediaTek SoC support
The linux-mediatek IRC channel has moved to liber.chat for quite some
time. Apart from that, not all patches are also send to LKML, so add
this ML explicitly.
And last but not least:
Angelo does a wunderfull job in reviewing patches for all kind of
devices from MediaTek.
The Meson G12A Internal PHY does not support standard IEEE MMD extended
register access, therefore add generic dummy stubs to fail the read and
write MMD calls. This is necessary to prevent the core PHY code from
erroneously believing that EEE is supported by this PHY even though this
PHY does not support EEE, as MMD register access returns all FFFFs.
Yan Zhai [Mon, 30 Jan 2023 20:51:48 +0000 (12:51 -0800)]
net: fix NULL pointer in skb_segment_list
Commit 3a1296a38d0c ("net: Support GRO/GSO fraglist chaining.")
introduced UDP listifyed GRO. The segmentation relies on frag_list being
untouched when passing through the network stack. This assumption can be
broken sometimes, where frag_list itself gets pulled into linear area,
leaving frag_list being NULL. When this happens it can trigger
following NULL pointer dereference, and panic the kernel. Reverse the
test condition should fix it.
Fixes: 3a1296a38d0c ("net: Support GRO/GSO fraglist chaining.") Suggested-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Yan Zhai <yan@cloudflare.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/r/Y9gt5EUizK1UImEP@debian Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Mon, 30 Jan 2023 19:30:51 +0000 (21:30 +0200)]
net: fman: memac: free mdio device if lynx_pcs_create() fails
When memory allocation fails in lynx_pcs_create() and it returns NULL,
there remains a dangling reference to the mdiodev returned by
of_mdio_find_device() which is leaked as soon as memac_pcs_create()
returns empty-handed.
Fixes: a7c2a32e7f22 ("net: fman: memac: Use lynx pcs driver") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Sean Anderson <sean.anderson@seco.com> Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Link: https://lore.kernel.org/r/20230130193051.563315-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
projects / mirror_ubuntu-kernels.git / log