octeon_mgmt: Fix MIX registers configuration on MTU setup
octeon_mgmt driver doesn't drop RX frames that are 1-4 bytes bigger than
MTU set for the corresponding interface. The problem is in the
AGL_GMX_RX0/1_FRM_MAX register setting, which should not account for VLAN
tagging.
According to Octeon HW manual:
"For tagged frames, MAX increases by four bytes for each VLAN found up to a
maximum of two VLANs, or MAX + 8 bytes."
OCTEON_FRAME_HEADER_LEN "define" is fine for ring buffer management, but
should not be used for AGL_GMX_RX0/1_FRM_MAX.
The problem could be easily reproduced using "ping" command. If affected
system has default MTU 1500, other host (having MTU >= 1504) can
successfully "ping" the affected system with payload size 1473-1476,
resulting in IP packets of size 1501-1504 accepted by the mgmt driver.
Fixed system still accepts IP packets of 1500 bytes even with VLAN tagging,
because the limits are lifted in HW as expected, for every VLAN tag.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
SMC ioctl processing requires the sock lock to work properly in
all thinkable scenarios.
Problem has been found with RaceFuzzer and fixes:
KASAN: null-ptr-deref Read in smc_ioctl
Reported-by: Byoungyoung Lee <lifeasageek@gmail.com> Reported-by: syzbot+35b2c5aa76fd398b9fd4@syzkaller.appspotmail.com Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch has fix for TX timeout while running bi-directional
traffic with 100 Mbps using 5762.
Signed-off-by: Sanjeev Bansal <sanjeevb.bansal@broadcom.com> Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Allen [Mon, 16 Jul 2018 15:29:30 +0000 (10:29 -0500)]
ibmvnic: Fix error recovery on login failure
Testing has uncovered a failure case that is not handled properly. In the
event that a login fails and we are not able to recover on the spot, we
return 0 from do_reset, preventing any error recovery code from being
triggered. Additionally, the state is set to "probed" meaning that when we
are able to trigger the error recovery, the driver always comes up in the
probed state. To handle the case properly, we need to return a failure code
here and set the adapter state to the state that we entered the reset in
indicating the state that we would like to come out of the recovery reset
in.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Wahren [Sun, 15 Jul 2018 19:53:20 +0000 (21:53 +0200)]
net: lan78xx: Fix race in tx pending skb size calculation
The skb size calculation in lan78xx_tx_bh is in race with the start_xmit,
which could lead to rare kernel oopses. So protect the whole skb walk with
a spin lock. As a benefit we can unlink the skb directly.
This patch was tested on Raspberry Pi 3B+
Link: https://github.com/raspberrypi/linux/issues/2608 Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet") Cc: stable <stable@vger.kernel.org> Signed-off-by: Floris Bos <bos@je-eigen-domein.nl> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Sun, 15 Jul 2018 16:35:19 +0000 (09:35 -0700)]
net/ipv6: Do not allow device only routes via the multipath API
Eric reported that reverting the patch that fixed and simplified IPv6
multipath routes means reverting back to invalid userspace notifications.
eg.,
$ ip -6 route add 2001:db8:1::/64 nexthop dev eth0 nexthop dev eth1
only generates a single notification:
2001:db8:1::/64 dev eth0 metric 1024 pref medium
While working on a fix for this problem I found another case that is just
broken completely - a multipath route with a gateway followed by device
followed by gateway:
$ ip -6 ro add 2001:db8:103::/64
nexthop via 2001:db8:1::64
nexthop dev dummy2
nexthop via 2001:db8:3::64
In this case the device only route is dropped completely - no notification
to userpsace but no addition to the FIB either:
$ ip -6 ro ls
2001:db8:1::/64 dev dummy1 proto kernel metric 256 pref medium
2001:db8:2::/64 dev dummy2 proto kernel metric 256 pref medium
2001:db8:3::/64 dev dummy3 proto kernel metric 256 pref medium
2001:db8:103::/64 metric 1024
nexthop via 2001:db8:1::64 dev dummy1 weight 1
nexthop via 2001:db8:3::64 dev dummy3 weight 1 pref medium
fe80::/64 dev dummy1 proto kernel metric 256 pref medium
fe80::/64 dev dummy2 proto kernel metric 256 pref medium
fe80::/64 dev dummy3 proto kernel metric 256 pref medium
Really, IPv6 multipath is just FUBAR'ed beyond repair when it comes to
device only routes, so do not allow it all.
This change will break any scripts relying on the mpath api for insert,
but I don't see any other way to handle the permutations. Besides, since
the routes are added to the FIB as standalone (non-multipath) routes the
kernel is not doing what the user requested, so it might as well tell the
user that.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Baranoff [Sun, 15 Jul 2018 15:36:37 +0000 (11:36 -0400)]
tcp: Fix broken repair socket window probe patch
Correct previous bad attempt at allowing sockets to come out of TCP
repair without sending window probes. To avoid changing size of
the repair variable in struct tcp_sock, this lets the decision for
sending probes or not to be made when coming out of repair by
introducing two ways to turn it off.
v2:
* Remove erroneous comment; defines now make behavior clear
Fixes: 70b7ff130224 ("tcp: allow user to create repair socket without window probes") Signed-off-by: Stefan Baranoff <sbaranoff@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Andrei Vagin <avagin@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When a new rx packet arrives, the rx path will decide whether to reuse
the remainder of the page or not according to one of the below conditions:
1. frag_info->frag_stride == PAGE_SIZE / 2
2. frags->page_offset + frag_info->frag_size > PAGE_SIZE;
The first condition is no met for when XDP is set.
For XDP, page_offset is always set to priv->rx_headroom which is
XDP_PACKET_HEADROOM and frag_info->frag_size is around mtu size + some
padding, still the 2nd release condition will hold since
XDP_PACKET_HEADROOM + 1536 < PAGE_SIZE, as a result the page will not
be released and will be _wrongly_ reused for next free rx descriptor.
In XDP there is an assumption to have a page per packet and reuse can
break such assumption and might cause packet data corruptions.
Fix this by adding an extra condition (!priv->rx_headroom) to the 2nd
case to avoid page reuse when XDP is set, since rx_headroom is set to 0
for non XDP setup and set to XDP_PACKET_HEADROOM for XDP setup.
No additional cache line is required for the new condition.
Fixes: 34db548bfb95 ("mlx4: add page recycling in receive path") Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Suggested-by: Martin KaFai Lau <kafai@fb.com> CC: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
CC [M] drivers/net/ethernet/freescale/fman/fman.o
In file included from ../drivers/net/ethernet/freescale/fman/fman.c:35:
../include/linux/fsl/guts.h: In function 'guts_set_dmacr':
../include/linux/fsl/guts.h:165:2: error: implicit declaration of function 'clrsetbits_be32' [-Werror=implicit-function-declaration]
clrsetbits_be32(&guts->dmacr, 3 << shift, device << shift);
^~~~~~~~~~~~~~~
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Madalin Bucur <madalin.bucur@nxp.com> Cc: netdev@vger.kernel.org Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: David S. Miller <davem@davemloft.net>
hv/netvsc: fix handling of fallback to single queue mode
The netvsc device may need to fallback to running in single queue
mode if host side only wants to support single queue.
Recent change for handling mtu broke this in setup logic.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 3ffe64f1a641 ("hv_netvsc: split sub-channel setup into async and sync") Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Fri, 13 Jul 2018 17:03:32 +0000 (12:03 -0500)]
ibmvnic: Revise RX/TX queue error messages
During a device failover, there may be latency between the loss
of the current backing device and a notification from firmware that
a failover has occurred. This latency can result in a large amount of
error printouts as firmware returns outgoing traffic with a generic
error code. These are not necessarily errors in this case as the
firmware is busy swapping in a new backing adapter and is not ready
to send packets yet. This patch reclassifies those error codes as
warnings with an explanation that a failover may be pending. All
other return codes will be considered errors.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: make DAD fail with enhanced DAD when nonce length differs
Commit adc176c54722 ("ipv6 addrconf: Implemented enhanced DAD (RFC7527)")
added enhanced DAD with a nonce length of 6 bytes. However, RFC7527
doesn't specify the length of the nonce, other than being 6 + 8*k bytes,
with integer k >= 0 (RFC3971 5.3.2). The current implementation simply
assumes that the nonce will always be 6 bytes, but others systems are
free to choose different sizes.
If another system sends a nonce of different length but with the same 6
bytes prefix, it shouldn't be considered as the same nonce. Thus, check
that the length of the received nonce is the same as the length we sent.
Ugly scapy test script running on veth0:
def loop():
pkt=sniff(iface="veth0", filter="icmp6", count=1)
pkt = pkt[0]
b = bytearray(pkt[Raw].load)
b[1] += 1
b += b'\xde\xad\xbe\xef\xde\xad\xbe\xef'
pkt[Raw].load = bytes(b)
pkt[IPv6].plen += 8
# fixup checksum after modifying the payload
pkt[IPv6].payload.cksum -= 0x3b44
if pkt[IPv6].payload.cksum < 0:
pkt[IPv6].payload.cksum += 0xffff
sendp(pkt, iface="veth0")
This should result in DAD failure for any address added to veth0's peer,
but is currently ignored.
Fixes: adc176c54722 ("ipv6 addrconf: Implemented enhanced DAD (RFC7527)") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch remove the following documentation warning
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:103: warning: Excess function parameter 'priv' description in 'stmmac_axi_setup'
It was introduced in commit afea03656add7 ("stmmac: rework DMA bus setting and introduce new platform AXI structure")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A KASAN:use-after-free bug was found related to ip6-erspan
while running selftests/net/ip6_gre_headroom.sh
It happens because of following sequence:
- ipv6hdr pointer is obtained from skb
- skb_cow_head() is called, skb->head memory is reallocated
- old data is accessed using ipv6hdr pointer
skb_cow_head() call was added in e41c7c68ea77 ("ip6erspan: make sure
enough headroom at xmit."), but looking at the history there was a
chance of similar bug because gre_handle_offloads() and pskb_trim()
can also reallocate skb->head memory. Fixes tag points to commit
which introduced possibility of this bug.
This patch moves ipv6hdr pointer assignment after skb_cow_head() call.
Fixes: 5a963eb61b7c ("ip6_gre: Add ERSPAN native tunnel support") Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp> Reviewed-by: Greg Rose <gvrose8192@gmail.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
On XDP_TX we need to free up the frame only when tun_xdp_tx() returns a
negative value. A positive value indicates that the packet is
successfully enqueued to the ptr_ring, so freeing the page causes
use-after-free.
Fixes: 735fc4054b3a ("xdp: change ndo_xdp_xmit API to support bulking") Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by: Jason Wang <jasowang@redhat.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Watson [Thu, 12 Jul 2018 15:03:43 +0000 (08:03 -0700)]
tls: Stricter error checking in zerocopy sendmsg path
In the zerocopy sendmsg() path, there are error checks to revert
the zerocopy if we get any error code. syzkaller has discovered
that tls_push_record can return -ECONNRESET, which is fatal, and
happens after the point at which it is safe to revert the iter,
as we've already passed the memory to do_tcp_sendpages.
Previously this code could return -ENOMEM and we would want to
revert the iter, but AFAIK this no longer returns ENOMEM after a447da7d004 ("tls: fix waitall behavior in tls_sw_recvmsg"),
so we fail for all error codes.
Reported-by: syzbot+c226690f7b3126c5ee04@syzkaller.appspotmail.com Reported-by: syzbot+709f2810a6a05f11d4d3@syzkaller.appspotmail.com Signed-off-by: Dave Watson <davejwatson@fb.com> Fixes: 3c4d7559159b ("tls: kernel TLS support") Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Constantine Shulyupin <const@MakeLinux.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Biggers [Wed, 11 Jul 2018 17:46:29 +0000 (10:46 -0700)]
KEYS: DNS: fix parsing multiple options
My recent fix for dns_resolver_preparse() printing very long strings was
incomplete, as shown by syzbot which still managed to hit the
WARN_ONCE() in set_precision() by adding a crafted "dns_resolver" key:
precision 50001 too large
WARNING: CPU: 7 PID: 864 at lib/vsprintf.c:2164 vsnprintf+0x48a/0x5a0
The bug this time isn't just a printing bug, but also a logical error
when multiple options ("#"-separated strings) are given in the key
payload. Specifically, when separating an option string into name and
value, if there is no value then the name is incorrectly considered to
end at the end of the key payload, rather than the end of the current
option. This bypasses validation of the option length, and also means
that specifying multiple options is broken -- which presumably has gone
unnoticed as there is currently only one valid option anyway.
A similar problem also applied to option values, as the kstrtoul() when
parsing the "dnserror" option will read past the end of the current
option and into the next option.
Fix these bugs by correctly computing the length of the option name and
by copying the option value, null-terminated, into a temporary buffer.
Reproducer for "dnserror" option being parsed incorrectly (expected
behavior is to fail when seeing the unknown option "foo", actual
behavior was to read the dnserror value as "1#foo" and fail there):
Reported-by: syzbot <syzkaller@googlegroups.com> Fixes: 4a2d789267e0 ("DNS: If the DNS server returns an error, allow that to be cached [ver #2]") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
multicast: init as INCLUDE when join SSM INCLUDE group
Based on RFC3376 5.1 and RFC3810 6.1, we should init as INCLUDE when join SSM
INCLUDE group. In my first version I only clear the group change record. But
this is not enough as when a new group join, it will init as EXCLUDE and
trigger an filter mode change in ip/ip6_mc_add_src(), which will clear all
source addresses' sf_crcount. This will prevent early joined address sending
state change records if multi source addresses joined at the same time.
In this v2 patchset, I fixed it by directly initializing the mode to INCLUDE
for SSM JOIN_SOURCE_GROUP. I also split the original patch into two separated
patches for IPv4 and IPv6.
Test: test by myself and customer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Tue, 10 Jul 2018 14:41:27 +0000 (22:41 +0800)]
ipv6/mcast: init as INCLUDE when join SSM INCLUDE group
This an IPv6 version patch of "ipv4/igmp: init group mode as INCLUDE when
join source group". From RFC3810, part 6.1:
If no per-interface state existed for that
multicast address before the change (i.e., the change consisted of
creating a new per-interface record), or if no state exists after the
change (i.e., the change consisted of deleting a per-interface
record), then the "non-existent" state is considered to have an
INCLUDE filter mode and an empty source list.
Which means a new multicast group should start with state IN(). Currently,
for MLDv2 SSM JOIN_SOURCE_GROUP mode, we first call ipv6_sock_mc_join(),
then ip6_mc_source(), which will trigger a TO_IN() message instead of
ALLOW().
The issue was exposed by commit a052517a8ff65 ("net/multicast: should not
send source list records when have filter mode change"). Before this change,
we sent both ALLOW(A) and TO_IN(A). Now, we only send TO_IN(A).
Fix it by adding a new parameter to init group mode. Also add some wrapper
functions to avoid changing too much code.
v1 -> v2:
In the first version I only cleared the group change record. But this is not
enough. Because when a new group join, it will init as EXCLUDE and trigger
a filter mode change in ip/ip6_mc_add_src(), which will clear all source
addresses sf_crcount. This will prevent early joined address sending state
change records if multi source addressed joined at the same time.
In v2 patch, I fixed it by directly initializing the mode to INCLUDE for SSM
JOIN_SOURCE_GROUP. I also split the original patch into two separated patches
for IPv4 and IPv6.
There is also a difference between v4 and v6 version. For IPv6, when the
interface goes down and up, we will send correct state change record with
unspecified IPv6 address (::) with function ipv6_mc_up(). But after DAD is
completed, we resend the change record TO_IN() in mld_send_initial_cr().
Fix it by sending ALLOW() for INCLUDE mode in mld_send_initial_cr().
Fixes: a052517a8ff65 ("net/multicast: should not send source list records when have filter mode change") Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Tue, 10 Jul 2018 14:41:26 +0000 (22:41 +0800)]
ipv4/igmp: init group mode as INCLUDE when join source group
Based on RFC3376 5.1
If no interface
state existed for that multicast address before the change (i.e., the
change consisted of creating a new per-interface record), or if no
state exists after the change (i.e., the change consisted of deleting
a per-interface record), then the "non-existent" state is considered
to have a filter mode of INCLUDE and an empty source list.
Which means a new multicast group should start with state IN().
Function ip_mc_join_group() works correctly for IGMP ASM(Any-Source Multicast)
mode. It adds a group with state EX() and inits crcount to mc_qrv,
so the kernel will send a TO_EX() report message after adding group.
But for IGMPv3 SSM(Source-specific multicast) JOIN_SOURCE_GROUP mode, we
split the group joining into two steps. First we join the group like ASM,
i.e. via ip_mc_join_group(). So the state changes from IN() to EX().
Then we add the source-specific address with INCLUDE mode. So the state
changes from EX() to IN(A).
Before the first step sends a group change record, we finished the second
step. So we will only send the second change record. i.e. TO_IN(A).
Regarding the RFC stands, we should actually send an ALLOW(A) message for
SSM JOIN_SOURCE_GROUP as the state should mimic the 'IN() to IN(A)'
transition.
The issue was exposed by commit a052517a8ff65 ("net/multicast: should not
send source list records when have filter mode change"). Before this change,
we used to send both ALLOW(A) and TO_IN(A). After this change we only send
TO_IN(A).
Fix it by adding a new parameter to init group mode. Also add new wrapper
functions so we don't need to change too much code.
v1 -> v2:
In my first version I only cleared the group change record. But this is not
enough. Because when a new group join, it will init as EXCLUDE and trigger
an filter mode change in ip/ip6_mc_add_src(), which will clear all source
addresses' sf_crcount. This will prevent early joined address sending state
change records if multi source addressed joined at the same time.
In v2 patch, I fixed it by directly initializing the mode to INCLUDE for SSM
JOIN_SOURCE_GROUP. I also split the original patch into two separated patches
for IPv4 and IPv6.
Fixes: a052517a8ff65 ("net/multicast: should not send source list records when have filter mode change") Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 14 Jul 2018 01:30:19 +0000 (18:30 -0700)]
Merge branch 'fix-DCTCP-delayed-ACK'
Yuchung Cheng says:
====================
fix DCTCP delayed ACK
This patch series addresses the issue that sometimes DCTCP
fail to acknowledge the latest sequence and result in sender timeout
if inflight is small.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After fixing the way DCTCP tracking delayed ACKs, the delayed-ACK
related callbacks are no longer needed
Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Lawrence Brakmo <brakmo@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, when a data segment was sent an ACK was piggybacked
on the data segment without generating a CA_EVENT_NON_DELAYED_ACK
event to notify congestion control modules. So the DCTCP
ca->delayed_ack_reserved flag could incorrectly stay set when
in fact there were no delayed ACKs being reserved. This could result
in sending a special ECN notification ACK that carries an older
ACK sequence, when in fact there was no need for such an ACK.
DCTCP keeps track of the delayed ACK status with its own separate
state ca->delayed_ack_reserved. Previously it may accidentally cancel
the delayed ACK without updating this field upon sending a special
ACK that carries a older ACK sequence. This inconsistency would
lead to DCTCP receiver never acknowledging the latest data until the
sender times out and retry in some cases.
+0.010 < [ect0] W. 4501:5501(1000) ack 4 win 257
// Previously the ACK sequence below would be 4501, causing a long RTO
+0.040~+0.045 > [ect01] . 4:4(0) ack 5501 // delayed ack
+0.311 < [ect0] . 5501:6501(1000) ack 4 win 257 // More data
+0 > [ect01] . 4:4(0) ack 6501 // now acks everything
+0.500 < F. 9501:9501(0) ack 4 win 257
Reported-by: Larry Brakmo <brakmo@fb.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Lawrence Brakmo <brakmo@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 12 Jul 2018 12:23:45 +0000 (15:23 +0300)]
qlogic: check kstrtoul() for errors
We accidentally left out the error handling for kstrtoul().
Fixes: a520030e326a ("qlcnic: Implement flash sysfs callback for 83xx adapter") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix AF_XDP TX error reporting before final kernel release such that it
becomes consistent between copy mode and zero-copy, from Magnus.
2) Fix three different syzkaller reported issues: oob due to ld_abs
rewrite with too large offset, another oob in l3 based skb test run
and a bug leaving mangled prog in subprog JITing error path, from Daniel.
3) Fix BTF handling for bitfield extraction on big endian, from Okash.
4) Fix a missing linux/errno.h include in cgroup/BPF found by kbuild bot,
from Roman.
5) Fix xdp2skb_meta.sh sample by using just command names instead of
absolute paths for tc and ip and allow them to be redefined, from Taeung.
6) Fix availability probing for BPF seg6 helpers before final kernel ships
so they can be detected at prog load time, from Mathieu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
skbuff: Unconditionally copy pfmemalloc in __skb_clone()
Commit 8b7008620b84 ("net: Don't copy pfmemalloc flag in
__copy_skb_header()") introduced a different handling for the
pfmemalloc flag in copy and clone paths.
In __skb_clone(), now, the flag is set only if it was set in the
original skb, but not cleared if it wasn't. This is wrong and
might lead to socket buffers being flagged with pfmemalloc even
if the skb data wasn't allocated from pfmemalloc reserves. Copy
the flag instead of ORing it.
Reported-by: Sabrina Dubroca <sd@queasysnail.net> Fixes: 8b7008620b84 ("net: Don't copy pfmemalloc flag in __copy_skb_header()") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Tested-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
This patch set adjusts the AF_XDP TX error reporting so that it becomes
consistent between copy mode and zero-copy. First some background:
Copy-mode for TX uses the SKB path in which the action of sending the
packet is performed from process context using the sendmsg
syscall. Completions are usually done asynchronously from NAPI mode by
using a TX interrupt. In this mode, send errors can be returned back
through the syscall.
In zero-copy mode both the sending of the packet and the completions
are done asynchronously from NAPI mode for performance reasons. In
this mode, the sendmsg syscall only makes sure that the TX NAPI loop
will be run that performs both the actions of sending and
completing. In this mode it is therefore not possible to return errors
through the sendmsg syscall as the sending is done from the NAPI
loop. Note that it is possible to implement a synchronous send with
our API, but in our benchmarks that made the TX performance drop by
nearly half due to synchronization requirements and cache line
bouncing. But for some netdevs this might be preferable so let us
leave it up to the implementation to decide.
The problem is that the current code base returns some errors in
copy-mode that are not possible to return in zero-copy mode. This
patch set aligns them so that the two modes always return the same
error code. We achieve this by removing some of the errors returned by
sendmsg in copy-mode (and in one case adding an error message for
zero-copy mode) and offering alternative error detection methods that
are consistent between the two modes.
The structure of the patch set is as follows:
Patch 1: removes the ENXIO return code from copy-mode when someone has
forcefully changed the number of queues on the device so that the
queue bound to the socket is no longer available. Just silently stop
sending anything as in zero-copy mode.
Patch 2: stop returning EAGAIN in copy mode when the completion queue
is full as zero-copy does not do this. Instead this situation can be
detected by comparing the head and tail pointers of the completion
queue in both modes. In any case, EAGAIN was not the correct error code
here since no amount of calling sendmsg will solve the problem. Only
consuming one or more messages on the completion queue will fix this.
Patch 3: Always return ENOBUFS from sendmsg if there is no TX queue
configured. This was not the case for zero-copy mode.
Patch 4: stop returning EMSGSIZE when the size of the packet is larger
than the MTU. Just send it to the device so that it will drop it as in
zero-copy mode.
Note that copy-mode can still return EAGAIN in certain circumstances,
but as these conditions cannot occur in zero-copy mode it is fine for
copy-mode to return them.
====================
Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Magnus Karlsson [Wed, 11 Jul 2018 08:12:52 +0000 (10:12 +0200)]
xsk: do not return EMSGSIZE in copy mode for packets larger than MTU
This patch stops returning EMSGSIZE from sendmsg in copy mode when the
size of the packet is larger than the MTU. Just send it to the device
so that it will drop it as in zero-copy mode. This makes the error
reporting consistent between copy mode and zero-copy mode.
Fixes: 35fcde7f8deb ("xsk: support for Tx") Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Magnus Karlsson [Wed, 11 Jul 2018 08:12:51 +0000 (10:12 +0200)]
xsk: always return ENOBUFS from sendmsg if there is no TX queue
This patch makes sure ENOBUFS is always returned from sendmsg if there
is no TX queue configured. This was not the case for zero-copy
mode. With this patch this error reporting is consistent between copy
mode and zero-copy mode.
Fixes: ac98d8aab61b ("xsk: wire upp Tx zero-copy functions") Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Magnus Karlsson [Wed, 11 Jul 2018 08:12:50 +0000 (10:12 +0200)]
xsk: do not return EAGAIN from sendmsg when completion queue is full
This patch stops returning EAGAIN in TX copy mode when the completion
queue is full as zero-copy does not do this. Instead this situation
can be detected by comparing the head and tail pointers of the
completion queue in both modes. In any case, EAGAIN was not the
correct error code here since no amount of calling sendmsg will solve
the problem. Only consuming one or more messages on the completion
queue will fix this.
With this patch, the error reporting becomes consistent between copy
mode and zero-copy mode.
Fixes: 35fcde7f8deb ("xsk: support for Tx") Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Magnus Karlsson [Wed, 11 Jul 2018 08:12:49 +0000 (10:12 +0200)]
xsk: do not return ENXIO from TX copy mode
This patch removes the ENXIO return code from TX copy-mode when
someone has forcefully changed the number of queues on the device so
that the queue bound to the socket is no longer available. Just
silently stop sending anything as in zero-copy mode so the error
reporting gets consistent between the two modes.
Fixes: 35fcde7f8deb ("xsk: support for Tx") Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Willem de Bruijn [Wed, 11 Jul 2018 16:00:46 +0000 (12:00 -0400)]
selftests: in udpgso_bench do not test udp zerocopy
The udpgso benchmark compares various configurations of UDP and TCP.
Including one that is not upstream, udp zerocopy. This is a leftover
from the earlier RFC patchset.
The test is part of kselftests and run in continuous spinners. Remove
the failing case to make the test start passing.
Fixes: 3a687bef148d ("selftests: udp gso benchmark") Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Wed, 11 Jul 2018 16:00:45 +0000 (12:00 -0400)]
packet: reset network header if packet shorter than ll reserved space
If variable length link layer headers result in a packet shorter
than dev->hard_header_len, reset the network header offset. Else
skb->mac_len may exceed skb->len after skb_mac_reset_len.
packet_sendmsg_spkt already has similar logic.
Fixes: b84bbaf7a6c8 ("packet: in packet_snd start writing at link layer allocation") Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Don't copy pfmemalloc flag in __copy_skb_header()
The pfmemalloc flag indicates that the skb was allocated from
the PFMEMALLOC reserves, and the flag is currently copied on skb
copy and clone.
However, an skb copied from an skb flagged with pfmemalloc
wasn't necessarily allocated from PFMEMALLOC reserves, and on
the other hand an skb allocated that way might be copied from an
skb that wasn't.
So we should not copy the flag on skb copy, and rather decide
whether to allow an skb to be associated with sockets unrelated
to page reclaim depending only on how it was allocated.
Move the pfmemalloc flag before headers_start[0] using an
existing 1-bit hole, so that __copy_skb_header() doesn't copy
it.
When cloning, we'll now take care of this flag explicitly,
contravening to the warning comment of __skb_clone().
While at it, restore the newline usage introduced by commit b19372273164 ("net: reorganize sk_buff for faster
__copy_skb_header()") to visually separate bytes used in
bitfields after headers_start[0], that was gone after commit a9e419dc7be6 ("netfilter: merge ctinfo into nfct pointer storage
area"), and describe the pfmemalloc flag in the kernel-doc
structure comment.
This doesn't change the size of sk_buff or cacheline boundaries,
but consolidates the 15 bits hole before tc_index into a 2 bytes
hole before csum, that could now be filled more easily.
Reported-by: Patrick Talbert <ptalbert@redhat.com> Fixes: c93bdd0e03e8 ("netvm: allow skb allocation to use PFMEMALLOC reserves") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We should take and release the filter_sem consistently during the
reset process, in the same manner as the mac_lock and reset_lock.
For lockdep consistency we also take the filter_sem for write around
other calls to efx->type->init().
Fixes: c2bebe37c6b6 ("sfc: give ef10 its own rwsem in the filter table instead of filter_lock") Signed-off-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In some situations we may end up calling down_read while already
holding the semaphore for write, thus hanging. This has been seen
when setting the MAC address for the interface. The hung task log
in this situation includes this stack:
down_read
efx_ef10_filter_insert
efx_ef10_filter_insert_addr_list
efx_ef10_filter_vlan_sync_rx_mode
efx_ef10_filter_add_vlan
efx_ef10_filter_table_probe
efx_ef10_set_mac_address
efx_set_mac_address
dev_set_mac_address
In addition, lockdep rightly points out that nested calling of
down_read is incorrect.
Fixes: c2bebe37c6b6 ("sfc: give ef10 its own rwsem in the filter table instead of filter_lock") Tested-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: systemport: Fix CRC forwarding check for SYSTEMPORT Lite
SYSTEMPORT Lite reversed the logic compared to SYSTEMPORT, the
GIB_FCS_STRIP bit is set when the Ethernet FCS is stripped, and that bit
is not set by default. Fix the logic such that we properly check whether
that bit is set or not and we don't forward an extra 4 bytes to the
network stack.
Fixes: 44a4524c54af ("net: systemport: Add support for SYSTEMPORT Lite") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Baranoff [Tue, 10 Jul 2018 21:31:10 +0000 (17:31 -0400)]
tcp: allow user to create repair socket without window probes
Under rare conditions where repair code may be used it is possible that
window probes are either unnecessary or undesired. If the user knows that
window probes are not wanted or needed this change allows them to skip
sending them when a socket comes out of repair.
Signed-off-by: Stefan Baranoff <sbaranoff@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Baranoff [Tue, 10 Jul 2018 21:25:20 +0000 (17:25 -0400)]
tcp: fix sequence numbers for repaired sockets re-using TIME-WAIT sockets
This patch fixes a bug where the sequence numbers of a socket created using
TCP repair functionality are lower than set after connect is called.
This occurs when the repair socket overlaps with a TIME-WAIT socket and
triggers the re-use code. The amount lower is equal to the number of times
that a particular IP/port set is re-used and then put back into TIME-WAIT.
Re-using the first time the sequence number is 1 lower, closing that socket
and then re-opening (with repair) a new socket with the same addresses/ports
puts the sequence number 2 lower than set via setsockopt. The third time is
3 lower, etc. I have not tested what the limit of this acrewal is, if any.
The fix is, if a socket is in repair mode, to respect the already set
sequence number and timestamp when it would have already re-used the
TIME-WAIT socket.
Signed-off-by: Stefan Baranoff <sbaranoff@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
What happens in jit_subprogs() is that kcalloc() for the subprog func
buffer is failing with NULL where we then bail out. Latter is a plain
return -ENOMEM, and this is definitely not okay since earlier in the
loop we are walking all subprogs and temporarily rewrite insn->off to
remember the subprog id as well as insn->imm to temporarily point the
call to __bpf_call_base + 1 for the initial JIT pass. Thus, bailing
out in such state and handing this over to the interpreter is troublesome
since later/subsequent e.g. find_subprog() lookups are based on wrong
insn->imm.
Therefore, once we hit this point, we need to jump to out_free path
where we undo all changes from earlier loop, so that interpreter can
work on unmodified insn->{off,imm}.
Another point is that should find_subprog() fail in jit_subprogs() due
to a verifier bug, then we also should not simply defer the program to
the interpreter since also here we did partial modifications. Instead
we should just bail out entirely and return an error to the user who is
trying to load the program.
Fixes: 1c2a088a6626 ("bpf: x64: add JIT support for multi-function programs") Reported-by: syzbot+7d427828b2ea6e592804@syzkaller.appspotmail.com Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Jacob Keller [Tue, 10 Jul 2018 21:22:27 +0000 (14:22 -0700)]
sch_fq_codel: zero q->flows_cnt when fq_codel_init fails
When fq_codel_init fails, qdisc_create_dflt will cleanup by using
qdisc_destroy. This function calls the ->reset() op prior to calling the
->destroy() op.
Unfortunately, during the failure flow for sch_fq_codel, the ->flows
parameter is not initialized, so the fq_codel_reset function will null
pointer dereference.
This is caused because flows_cnt is non-zero, but flows hasn't been
initialized. fq_codel_init has left the private data in a partially
initialized state.
To fix this, reset flows_cnt to 0 when we fail to initialize.
Additionally, to make the state more consistent, also cleanup the flows
pointer when the allocation of backlogs fails.
This fixes the NULL pointer dereference, since both the for-loop and
memset in fq_codel_reset will be no-ops when flow_cnt is zero.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/networking/e1000.rst:83: ERROR: Unexpected indentation.
Documentation/networking/e1000.rst:84: WARNING: Block quote ends without a blank line; unexpected unindent.
Documentation/networking/e1000.rst:173: WARNING: Definition list ends without a blank line; unexpected unindent.
Documentation/networking/e1000.rst:236: WARNING: Definition list ends without a blank line; unexpected unindent.
While here, fix highlights and mark a table as such.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Dan Carpenter [Wed, 4 Jul 2018 09:53:37 +0000 (12:53 +0300)]
ixgbe: Off by one in ixgbe_ipsec_tx()
The ipsec->tx_tbl[] has IXGBE_IPSEC_MAX_SA_COUNT elements so the > needs
to be changed to >= so we don't read one element beyond the end of the
array.
Fixes: 592594704761 ("ixgbe: process the Tx ipsec offload") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Shannon Nelson <shannon.nelson@oracle.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Mon, 18 Jun 2018 16:02:00 +0000 (12:02 -0400)]
ixgbe: Be more careful when modifying MAC filters
This change makes it so that we are much more explicit about the ordering
of updates to the receive address register (RAR) table. Prior to this patch
I believe we may have been updating the table while entries were still
active, or possibly allowing for reordering of things since we weren't
explicitly flushing writes to either the lower or upper portion of the
register prior to accessing the other half.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Thu, 12 Jul 2018 07:19:06 +0000 (00:19 -0700)]
Merge branch 'ieee802154-for-davem-2018-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2018-07-11
An update from ieee802154 for your *net* tree.
Build system fix for a missing include from Arnd Bergmann.
Setting the IFLA_LINK for the lowpan parent from Lubomir Rintel.
Fixes for some RX corner cases in adf7242 driver by Michael Hennerich.
And some small patches to cleanup our BUG_ON vs WARN_ON usage.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 10 Jul 2018 11:05:36 +0000 (12:05 +0100)]
sfp: fix module initialisation with netdev already up
It was been observed that with a particular order of initialisation,
the netdev can be up, but the SFP module still has its TX_DISABLE
signal asserted. This occurs when the network device brought up before
the SFP kernel module has been inserted by userspace.
This occurs because sfp-bus layer does not hear about the change in
network device state, and so assumes that it is still down. Set
netdev->sfp when the upstream is registered to work around this problem.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 10 Jul 2018 11:05:31 +0000 (12:05 +0100)]
sfp: ensure we clean up properly on bus registration failure
We fail to correctly clean up after a bus registration failure, which
can lead to an incorrect assumption about the registration state of
the upstream or sfp cage.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
After scrubbing the BPF prog a bit from the noise, turns out it called
bpf_skb_change_head() for the lwt_xmit prog with headroom of 2. Nothing
wrong in that, however, this was run with repeat >> 0 in bpf_prog_test_run_skb()
and the same skb thus keeps changing until the pskb_expand_head() called
from skb_cow() keeps bailing out in atomic alloc context with -ENOMEM.
So upon return we'll basically have 0 headroom left yet blindly do the
__skb_push() of 14 bytes and keep copying data from there in bpf_test_finish()
out of bounds. Fix to check if we have enough headroom and if pskb_expand_head()
fails, bail out with error.
Another bug independent of this fix (but related in triggering above) is
that BPF_PROG_TEST_RUN should be reworked to reset the skb/xdp buffer to
it's original state from input as otherwise repeating the same test in a
loop won't work for benchmarking when underlying input buffer is getting
changed by the prog each time and reused for the next run leading to
unexpected results.
When extracting bitfield from a number, btf_int_bits_seq_show() builds
a mask and accesses least significant byte of the number in a way
specific to little-endian. This patch fixes that by checking endianness
of the machine and then shifting left and right the unneeded bits.
Thanks to Martin Lau for the help in navigating potential pitfalls when
dealing with endianess and for the final solution.
Fixes: b00b8daec828 ("bpf: btf: Add pretty print capability for data with BTF type info") Signed-off-by: Okash Khawaja <osk@fb.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
bpf_lwt_seg6_* helpers require CONFIG_IPV6_SEG6_BPF, and currently
return -EOPNOTSUPP to indicate unavailability. This patch forces the
BPF verifier to reject programs using these helpers when
!CONFIG_IPV6_SEG6_BPF, allowing users to more easily probe if they are
available or not.
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Daniel Borkmann [Mon, 9 Jul 2018 22:43:22 +0000 (00:43 +0200)]
bpf: fix ldx in ld_abs rewrite for large offsets
Mark reported that syzkaller triggered a KASAN detected slab-out-of-bounds
bug in ___bpf_prog_run() with a BPF_LD | BPF_ABS word load at offset 0x8001.
After further investigation it became clear that the issue was the
BPF_LDX_MEM() which takes offset as an argument whereas it cannot encode
larger than S16_MAX offsets into it. For this synthetical case we need to
move the full address into tmp register instead and do the LDX without
immediate value.
Fixes: e0cea7ce988c ("bpf: implement ld_abs/ld_ind in native bpf") Reported-by: syzbot <syzkaller@googlegroups.com> Reported-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
rhashtable: add restart routine in rhashtable_free_and_destroy()
rhashtable_free_and_destroy() cancels re-hash deferred work
then walks and destroys elements. at this moment, some elements can be
still in future_tbl. that elements are not destroyed.
test case:
nft_rhash_destroy() calls rhashtable_free_and_destroy() to destroy
all elements of sets before destroying sets and chains.
But rhashtable_free_and_destroy() doesn't destroy elements of future_tbl.
so that splat occurred.
David S. Miller [Mon, 9 Jul 2018 23:27:15 +0000 (16:27 -0700)]
Merge branch 'bnxt_en-Bug-fixes'
Michael Chan says:
====================
bnxt_en: Bug fixes.
These are bug fixes in error code paths, TC Flower VLAN TCI flow
checking bug fix, proper filtering of Broadcast packets if IFF_BROADCAST
is not set, and a bug fix in bnxt_get_max_rings() to return 0 ring
parameters when the return value is -ENOMEM.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bug in the error code path when bnxt_request_irq() returns failure.
bnxt_disable_napi() should not be called in this error path because
NAPI has not been enabled yet.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 9 Jul 2018 06:24:51 +0000 (02:24 -0400)]
bnxt_en: Do not modify max IRQ count after RDMA driver requests/frees IRQs.
Calling bnxt_set_max_func_irqs() to modify the max IRQ count requested or
freed by the RDMA driver is flawed. The max IRQ count is checked when
re-initializing the IRQ vectors and this can happen multiple times
during ifup or ethtool -L. If the max IRQ is reduced and the RDMA
driver is operational, we may not initailize IRQs correctly. This
problem shows up on VFs with very small number of MSIX.
There is no other logic that relies on the IRQ count excluding the ones
used by RDMA. So we fix it by just removing the call to subtract or
add the IRQs used by RDMA.
Fixes: a588e4580a7e ("bnxt_en: Add interface to support RDMA driver.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 9 Jul 2018 06:24:50 +0000 (02:24 -0400)]
bnxt_en: Support clearing of the IFF_BROADCAST flag.
Currently, the driver assumes IFF_BROADCAST is always set and always sets
the broadcast filter. Modify the code to set or clear the broadcast
filter according to the IFF_BROADCAST flag.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 9 Jul 2018 06:24:49 +0000 (02:24 -0400)]
bnxt_en: Always set output parameters in bnxt_get_max_rings().
The current code returns -ENOMEM and does not bother to set the output
parameters to 0 when no rings are available. Some callers, such as
bnxt_get_channels() will display garbage ring numbers when that happens.
Fix it by always setting the output parameters.
Fixes: 6e6c5a57fbe1 ("bnxt_en: Modify bnxt_get_max_rings() to support shared or non shared rings.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If there aren't enough RX rings available, the driver will attempt to
use a single RX ring without the aggregation ring. If that also
fails, the BNXT_FLAG_AGG_RINGS flag is cleared but the other ring
parameters are not set consistently to reflect that. If more RX
rings become available at the next open, the RX rings will be in
an inconsistent state and may crash when freeing the RX rings.
Fix it by restoring the BNXT_FLAG_AGG_RINGS if not enough RX rings are
available to run without aggregation rings.
Fixes: bdbd1eb59c56 ("bnxt_en: Handle no aggregation ring gracefully.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that OVS may set don’t care for DEI/CFI bit in
vlan_tci mask. Hence, checking for vlan_tci exact match will endup
in a vlan flow rejection.
This patch fixes the problem by checking for vlan_pcp and vid
separately, instead of checking for the entire vlan_tci.
Fixes: e85a9be93cf1 (bnxt_en: do not allow wildcard matches for L2 flows) Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following patchset contains Netfilter fixes for your net tree:
1) Missing module autoloadfor icmp and icmpv6 x_tables matches,
from Florian Westphal.
2) Possible non-linear access to TCP header from tproxy, from
Mate Eckl.
3) Do not allow rbtree to be used for single elements, this patch
moves all set backend into one single module since such thing
can only happen if hashtable module is explicitly blacklisted,
which should not ever be done.
4) Reject error and standard targets from nft_compat for sanity
reasons, they are never used from there.
5) Don't crash on double hashsize module parameter, from Andrey
Ryabinin.
6) Drop dst on skb before placing it in the fragmentation
reassembly queue, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: ipv6: nf_defrag: drop skb dst before queueing
Eric Dumazet reports:
Here is a reproducer of an annoying bug detected by syzkaller on our production kernel
[..]
./b78305423 enable_conntrack
Then :
sleep 60
dmesg | tail -10
[ 171.599093] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 181.631024] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 191.687076] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 201.703037] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 211.711072] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 221.959070] unregister_netdevice: waiting for lo to become free. Usage count = 2
Reproducer sends ipv6 fragment that hits nfct defrag via LOCAL_OUT hook.
skb gets queued until frag timer expiry -- 1 minute.
Normally nf_conntrack_reasm gets called during prerouting, so skb has
no dst yet which might explain why this wasn't spotted earlier.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Reported-by: John Sperbeck <jsperbeck@google.com> Signed-off-by: Florian Westphal <fw@strlen.de> Tested-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nf_conntrack: Fix possible possible crash on module loading.
Loading the nf_conntrack module with doubled hashsize parameter, i.e.
modprobe nf_conntrack hashsize=12345 hashsize=12345
causes NULL-ptr deref.
If 'hashsize' specified twice, the nf_conntrack_set_hashsize() function
will be called also twice.
The first nf_conntrack_set_hashsize() call will set the
'nf_conntrack_htable_size' variable:
nf_conntrack_set_hashsize()
...
/* On boot, we can set this without any fancy locking. */
if (!nf_conntrack_htable_size)
return param_set_uint(val, kp);
But on the second invocation, the nf_conntrack_htable_size is already set,
so the nf_conntrack_set_hashsize() will take a different path and call
the nf_conntrack_hash_resize() function. Which will crash on the attempt
to dereference 'nf_conntrack_hash' pointer:
Fix this, by checking !nf_conntrack_hash instead of
!nf_conntrack_htable_size. nf_conntrack_hash will be initialized only
after the module loaded, so the second invocation of the
nf_conntrack_set_hashsize() won't crash, it will just reinitialize
nf_conntrack_htable_size again.
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nft_compat: explicitly reject ERROR and standard target
iptables-nft never requests these, but make this explicitly illegal.
If it were quested, kernel could oops as ->eval is NULL, furthermore,
the builtin targets have no owning module so its possible to rmmod
eb/ip/ip6_tables module even if they would be loaded.
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Reissuing RC_RX every 400ms - to adjust for offset drift in
receiver see datasheet page 61, OCL section.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Roman Gushchin [Fri, 6 Jul 2018 21:34:29 +0000 (14:34 -0700)]
bpf: include errno.h from bpf-cgroup.h
Commit fdb5c4531c1e ("bpf: fix attach type BPF_LIRC_MODE2 dependency
wrt CONFIG_CGROUP_BPF") caused some build issues, detected by 0-DAY
kernel test infrastructure.
The problem is that cgroup_bpf_prog_attach/detach/query() functions
can return -EINVAL error code, which is not defined. Fix this adding
errno.h to includes.
Fixes: fdb5c4531c1e ("bpf: fix attach type BPF_LIRC_MODE2 dependency wrt CONFIG_CGROUP_BPF") Signed-off-by: Roman Gushchin <guro@fb.com> Cc: Sean Young <sean@mess.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Stefan Schmidt [Fri, 22 Sep 2017 12:13:54 +0000 (14:13 +0200)]
ieee802154: at86rf230: use __func__ macro for debug messages
Instead of having the function name hard-coded (it might change and we
forgot to update them in the debug output) we can use __func__ instead
and also shorter the line so we do not need to break it. Also fix an
extra blank line while being here.
Found by checkpatch.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Fixes: 05255b823a61 ("tcp: add TCP_ZEROCOPY_RECEIVE support for zerocopy receive") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 6 Jul 2018 10:30:20 +0000 (12:30 +0200)]
ipfrag: really prevent allocation on netns exit
Setting the low threshold to 0 has no effect on frags allocation,
we need to clear high_thresh instead.
The code was pre-existent to commit 648700f76b03 ("inet: frags:
use rhashtables for reassembly units"), but before the above,
such assignment had a different role: prevent concurrent eviction
from the worker and the netns cleanup helper.
Fixes: 648700f76b03 ("inet: frags: use rhashtables for reassembly units") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Colitti [Sat, 7 Jul 2018 07:31:40 +0000 (16:31 +0900)]
net: diag: Don't double-free TCP_NEW_SYN_RECV sockets in tcp_abort
When tcp_diag_destroy closes a TCP_NEW_SYN_RECV socket, it first
frees it by calling inet_csk_reqsk_queue_drop_and_and_put in
tcp_abort, and then frees it again by calling sock_gen_put.
Since tcp_abort only has one caller, and all the other codepaths
in tcp_abort don't free the socket, just remove the free in that
function.
Cc: David Ahern <dsa@cumulusnetworks.com>
Tested: passes Android sock_diag_test.py, which exercises this codepath Fixes: d7226c7a4dd1 ("net: diag: Fix refcnt leak in error path destroying socket") Signed-off-by: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsa@cumulusnetworks.com> Tested-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Sat, 7 Jul 2018 23:15:26 +0000 (16:15 -0700)]
net/ipv4: Set oif in fib_compute_spec_dst
Xin reported that icmp replies may not use the address on the device the
echo request is received if the destination address is broadcast. Instead
a route lookup is done without considering VRF context. Fix by setting
oif in flow struct to the master device if it is enslaved. That directs
the lookup to the VRF table. If the device is not enslaved, oif is still
0 so no affect.
Fixes: cd2fbe1b6b51 ("net: Use VRF device index for lookups on RX") Reported-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we end up with attempting to send packets from down devices
or to send oversized packets, which may cause unexpected driver/device
behaviour. Generic XDP has already done this check, so reuse the logic
in native XDP.
====================
First three patches resolve issues found while testing sockhash and
reviewing code. Syzbot also found them about the same time as I was
working on fixes. The main issue is in the sockhash path we reduced
the scope of sk_callback lock but this meant we could get update and
close running in parallel so fix that here.
Then testing sk_msg and sk_skb programs together found that skb->dev
is not always assigned and some of the helpers were depending on this
to lookup max mtu. Fix this by using SKB_MAX_ALLOC when no MTU is
available.
Finally, Martin spotted that the sockmap code was still using the
qdisc skb cb structure. But I was sure we had fixed this long ago.
Looks like we missed it in a merge conflict resolution and then by
chance data_end offset was the same in both structures so everything
sort of continued to work even though it could break at any moment
if the structs ever change. So redo the conversion and this time
also convert the helpers.
v2: fix '0 files changed' issue in patches
====================
we added the routine bpf_compute_data_end_sk_skb() to compute the
correct data_end values, but this has since been lost. In kernel
v4.14 this was correct and the above patch was applied in it
entirety. Then when v4.14 was merged into v4.15-rc1 net-next tree
we lost the piece that renamed bpf_compute_data_pointers to the
new function bpf_compute_data_end_sk_skb. This was done here,
When it conflicted with the following rename patch,
6aaae2b6c433 ("bpf: rename bpf_compute_data_end into bpf_compute_data_pointers")
Finally, after a refactor I thought even the function
bpf_compute_data_end_sk_skb() was no longer needed and it was
erroneously removed.
However, we never reverted the sk_skb_convert_ctx_access() usage of
tcp_skb_cb which had been committed and survived the merge conflict.
Here we fix this by adding back the helper and *_data_end_sk_skb()
usage. Using the bpf_skc_data_end mapping is not correct because it
expects a qdisc_skb_cb object but at the sock layer this is not the
case. Even though it happens to work here because we don't overwrite
any data in-use at the socket layer and the cb structure is cleared
later this has potential to create some subtle issues. But, even
more concretely the filter.c access check uses tcp_skb_cb.
So when we use offset_of() to track down the byte offset we get 40 in
either case and everything continues to work. Fix this mess and use
correct structures its unclear how long this might actually work for
until someone moves the structs around.
Reported-by: Martin KaFai Lau <kafai@fb.com> Fixes: e1ea2f9856b7 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net") Fixes: 6aaae2b6c433 ("bpf: rename bpf_compute_data_end into bpf_compute_data_pointers") Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
John Fastabend [Thu, 5 Jul 2018 15:50:10 +0000 (08:50 -0700)]
bpf: sockmap, consume_skb in close path
Currently, when a sock is closed and the bpf_tcp_close() callback is
used we remove memory but do not free the skb. Call consume_skb() if
the skb is attached to the buffer.
John Fastabend [Thu, 5 Jul 2018 15:50:04 +0000 (08:50 -0700)]
bpf: sockhash, disallow bpf_tcp_close and update in parallel
After latest lock updates there is no longer anything preventing a
close and recvmsg call running in parallel. Additionally, we can
race update with close if we close a socket and simultaneously update
if via the BPF userspace API (note the cgroup ops are already run
with sock_lock held).
To resolve this take sock_lock in close and update paths.
Reported-by: syzbot+b680e42077a0d7c9a0c4@syzkaller.appspotmail.com Fixes: e9db4ef6bf4c ("bpf: sockhash fix omitted bucket lock in sock_close") Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
John Fastabend [Thu, 5 Jul 2018 15:49:59 +0000 (08:49 -0700)]
bpf: fix sk_skb programs without skb->dev assigned
Multiple BPF helpers in use by sk_skb programs calculate the max
skb length using the __bpf_skb_max_len function. However, this
calculates the max length using the skb->dev pointer which can be
NULL when an sk_skb program is paired with an sk_msg program.
To force this a sk_msg program needs to redirect into the ingress
path of a sock with an attach sk_skb program. Then the the sk_skb
program would need to call one of the helpers that adjust the skb
size.
To fix the null ptr dereference use SKB_MAX_ALLOC size if no dev
is available.
====================
I missed fixing the error path in the sockhash code to align with
supporting socks in multiple maps. Simply checking if the psock is
present does not mean we can decrement the reference count because
it could be part of another map. Fix this by cleaning up the error
path so this situation does not happen.
====================
John Fastabend [Thu, 5 Jul 2018 15:05:56 +0000 (08:05 -0700)]
bpf: sockmap, error path can not release psock in multi-map case
The current code, in the error path of sock_hash_ctx_update_elem,
checks if the sock has a psock in the user data and if so decrements
the reference count of the psock. However, if the error happens early
in the error path we may have never incremented the psock reference
count and if the psock exists because the sock is in another map then
we may inadvertently decrement the reference count.
Fix this by making the error path only call smap_release_sock if the
error happens after the increment.
====================
net/sched: fix NULL dereference in 'goto chain' control action
in a couple of TC actions (i.e. csum and tunnel_key), the control action
is stored together with the action-specific configuration data.
This avoids a race condition (see [1]), but it causes a crash when 'goto
chain' is used with the above actions. Since this race condition is
tolerated on the other TC actions (it's present even on actions where the
spinlock is still used), storing the control action in the common area
should be acceptable for tunnel_key and csum as well.
net/sched: act_tunnel_key: fix NULL dereference when 'goto chain' is used
the control action in the common member of struct tcf_tunnel_key must be a
valid value, as it can contain the chain index when 'goto chain' is used.
Ensure that the control action can be read as x->tcfa_action, when x is a
pointer to struct tc_action and x->ops->type is TCA_ACT_TUNNEL_KEY, to
prevent the following command:
Fixes: d0f6dd8a914f ("net/sched: Introduce act_tunnel_key") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched: act_csum: fix NULL dereference when 'goto chain' is used
the control action in the common member of struct tcf_csum must be a valid
value, as it can contain the chain index when 'goto chain' is used. Ensure
that the control action can be read as x->tcfa_action, when x is a pointer
to struct tc_action and x->ops->type is TCA_ACT_CSUM, to prevent the
following command:
# tc filter add dev $h2 ingress protocol ip pref 1 handle 101 flower \
> $tcflags dst_mac $h2mac action csum ip or tcp or udp or sctp goto chain 1
from triggering a NULL pointer dereference when a matching packet is
received.
Fixes: 9c5f69bbd75a ("net/sched: act_csum: don't use spinlock in the fast path") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: macb: Allocate valid memory for TX and RX BD prefetch
GEM version in ZynqMP and most versions greater than r1p07 supports
TX and RX BD prefetch. The number of BDs that can be prefetched is a
HW configurable parameter. For ZynqMP, this parameter is 4.
When GEM DMA is accessing the last BD in the ring, even before the
BD is processed and the WRAP bit is noticed, it will have prefetched
BDs outside the BD ring. These will not be processed but it is
necessary to have accessible memory after the last BD. Especially
in cases where SMMU is used, memory locations immediately after the
last BD may not have translation tables triggering HRESP errors. Hence
always allocate extra BDs to accommodate for prefetch.
The value of tx/rx bd prefetch for any given SoC version is:
2 ^ (corresponding field in design config 10 register).
(value of this field >= 1)
Added a capability flag so that older IP versions that do not have
DCFG10 or this prefetch capability are not affected.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-eoan-kernel.git / log