This introduces pSeries_reconfig_notify() as a just wrapper of
blocking_notifier_call_chain() for pSeries_reconfig_chain.
This is a preparation to improvement of error code on reconfiguration
notifier failure.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Scott Wood [Wed, 22 Jun 2011 11:25:42 +0000 (11:25 +0000)]
powerpc/book3e-64: use a separate TLB handler when linear map is bolted
On MMUs such as FSL where we can guarantee the entire linear mapping is
bolted, we don't need to worry about linear TLB misses. If on top of
that we do a full table walk, we get rid of all recursive TLB faults, and
can dispense with some state saving. This gains a few percent on
TLB-miss-heavy workloads, and around 50% on a benchmark that had a high
rate of virtual page table faults under the normal handler.
While touching the EX_TLB layout, remove EX_TLB_MMUCR0, EX_TLB_SRR0, and
EX_TLB_SRR1 as they're not used.
[BenH: Fixed build with 64K pages (wsp config)]
Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Timur Tabi [Tue, 14 Jun 2011 13:04:33 +0000 (13:04 +0000)]
powerpc/85xx: disable timebase synchronization under the hypervisor
The Freescale hypervisor does not allow guests to write to the timebase
registers (virtualizing the timebase register was deemed too complicated),
so don't try to synchronize the timebase registers when we're running
under the hypervisor.
This typically happens when kexec support is enabled.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1010RDB Overview
-----------------
1Gbyte DDR3 (on board DDR)
32Mbyte 16bit NOR flash
32Mbyte SLC NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
I2C Board 128x8 bit memory
SD/MMC connector to interface with the SD memory card
2 SATA interface
1 internal SATA connect to 2.5. 160G SATA2 HDD
1 eSATA connector to rear panel
USB 2.0
x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
eTSEC1: Connected to RGMII PHY VSC8641XKO
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY VSC8221 eCAN
Two DB-9 female connectors for Field bus interface UART
DUART interface: supports two UARTs up to 115200 bps for console display
Timur Tabi [Thu, 23 Jun 2011 16:16:47 +0000 (11:16 -0500)]
powerpc/86xx: enable the framebuffer console on the MPC8610 HPCD
Enable framebuffer console support by default in the defconfig on the
Freescale MPC8610 HPCD reference board. This allows the boot messages to
be shown on the video display.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Thu, 23 Jun 2011 06:16:48 +0000 (06:16 +0000)]
powerpc/86xx: improve calculation of DIU pixel clock on the MPC8610 HPCD
mpc8610hpcd_set_pixel_clock() calculates the correct value of the PXCLK
bits in the CLKDVDR register for a given pixel clock rate. The code which
performs this calculation is overly complicated and includes an error
estimation routine that doesn't work most of the time anyway. Replace the
code with the simpler routine that's currently used on the P1022DS.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Thu, 23 Jun 2011 19:48:55 +0000 (14:48 -0500)]
powerpc/85xx: enable the framebuffer console for the defconfigs
Enable framebuffer console support by default in the defconfigs for the
Freescale 85xx-based reference board. This allows the boot messages to
be shown on the video display on the P1022DS.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Thu, 23 Jun 2011 19:48:54 +0000 (14:48 -0500)]
powerpc/85xx: clamp the P1022DS DIU pixel clock to allowed values
To ensure that the DIU pixel clock will not be set to an invalid value,
clamp the PXCLK divider to the allowed range (2-255). This also acts as
a limiter for the pixel clock.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Scott Wood [Wed, 22 Jun 2011 23:10:30 +0000 (18:10 -0500)]
powerpc/e500mc: Add support for the wait instruction in e500_idle
e500mc cannot doze or nap due to an erratum (as well as having a
different mechanism than previous e500), but it has a "wait" instruction
that is similar to doze.
On 64-bit, due to the soft-irq-disable mechanism, the existing
book3e_idle should be used instead.
Signed-off-by: Vakul Garg <vakul@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 22 Jun 2011 10:17:45 +0000 (05:17 -0500)]
powerpc/85xx: Add P4080 SoC device tree include stub
Split out common (non-board specific) parts of the SoC related device
tree into a stub so multiple board dts files can include it and we can
reduce duplication and maintenance effort.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FSL PCIe controller can act as agent(EP) or host(RC). Under Agent(EP) mode
the controller will be configured by the host system. So its not required
to be registered with the PCI(e) sub-system. We only register the
controller if its configured in host(RC) mode.
Timur Tabi [Thu, 19 May 2011 13:54:29 +0000 (08:54 -0500)]
powerpc: add Freescale hypervisor partition control functions
Add functions to restart and halt the current partition when running under
the Freescale hypervisor. These functions should be assigned to various
function pointers of the ppc_md structure during the .probe() function for
the board:
Ashish Kalra [Thu, 19 May 2011 13:54:28 +0000 (08:54 -0500)]
powerpc: introduce the ePAPR embedded hypervisor vmpic driver
The Freescale ePAPR reference hypervisor provides interrupt controller
services via a hypercall interface, instead of emulating the MPIC
controller. This is called the VMPIC.
The ePAPR "virtual interrupt controller" provides interrupt controller
services for external interrupts. External interrupts received by a
partition can come from two sources:
- Hardware interrupts - hardware interrupts come from external
interrupt lines or on-chip I/O devices.
- Virtual interrupts - virtual interrupts are generated by the hypervisor
as part of some hypervisor service or hypervisor-created virtual device.
Both types of interrupts are processed using the same programming model and
same set of hypercalls.
Signed-off-by: Ashish Kalra <ashish.kalra@freescale.com> Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
ePAPR hypervisors provide operating system services via a "hypercall"
interface. The following steps need to be performed to make an hcall:
1. Load r11 with the hcall number
2. Load specific other registers with parameters
3. Issue instrucion "sc 1"
4. The return code is in r3
5. Other returned parameters are in other registers.
To provide this service to the kernel, these steps are wrapped in inline
assembly functions. Standard ePAPR hcalls are in epapr_hcalls.h, and
Freescale extensions are in fsl_hcalls.h.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Stuart Yoder [Thu, 19 May 2011 13:54:26 +0000 (08:54 -0500)]
powerpc: make irq_choose_cpu() available to all PIC drivers
Move irq_choose_cpu() into arch/powerpc/kernel/irq.c so that it can be used
by other PIC drivers. The function is not MPIC-specific.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com> Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Roy Zang [Fri, 20 May 2011 01:20:13 +0000 (20:20 -0500)]
powerpc/85xx: Add basic P1023RDS board support
The P1023 processor is an e500v2 based SoC that utilizes the DPAA
networking architecture. This adds basic board support for non-DPAA
functionality (device tree, board file, etc).
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
powerpc/85xx: Save scratch registers to thread info instead of using SPRGs.
We expect this is actually faster, and we end up needing more space than we
can get from the SPRGs in some instances. This is also useful when running
as a guest OS - SPRGs4-7 do not have guest versions.
8 slots are allocated in thread_info for this even though we only actually
use 4 of them - this allows space for future code to have more scratch
space (and we know we'll need it for things like hugetlb).
Signed-off-by: Ashish Kalra <Ashish.Kalra@freescale.com> Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 20 May 2011 00:56:50 +0000 (19:56 -0500)]
powerpc/fsl_pci: Simplify matching logic for PCI_FIXUP_HEADER
We fixup every FSL PCIe Root Complex we need to fixup a few things.
Rather than adding every device under the sun we move to just matching
only on the vendor (PCI_VENDOR_ID_FREESCALE) and than check that we are
a PCIe controller in host mode in the fixup.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Mon, 9 May 2011 20:08:57 +0000 (15:08 -0500)]
powerpc/85xx: Cleanup PCIe support on corenet_ds boards
Several changes on PCIe support on P3041DS/P4080DS/P5020DS boards:
* Add support for "fsl,qoriq-pcie-v2.2" needed by P3041 & P5020
* Removed support for setting primary_phb_addr as we have no ISA need
* Add PCI controller to of_platform_bus_probe (for EDAC)
* Cleanup building w/SWIOTLB off on P4080DS (not stricly PCIe related)
Kumar Gala [Mon, 9 May 2011 19:13:13 +0000 (14:13 -0500)]
powerpc/85xx: Updates to P4080DS device tree
* Added BSD dual-license
* Moved mpic-parent to root so we dont need to duplicate everywhere
* Added next level cache from L2 to CPC
* Moved to 4-cell MPIC interrupt properties
* Added 3 MSI banks
* Added numerous missing nodes: soc-sram-error, guts, pins, clockgen,
rcpm, sfp, serdes, etc.
* Reworked PCIe interrupts to be at virtual bridge level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 19 May 2011 18:22:25 +0000 (13:22 -0500)]
powerpc: Add a defconfig for 'corenet' 32-bit platforms
The e500mc and e5500 based cores are only available on corenet based
SoCs. We use this name for the P204x, P3040, P4040, P4080, P50x0 SoCs
and any future processors in these families.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 19 May 2011 18:19:52 +0000 (13:19 -0500)]
powerpc: Rename e55xx_smp_defconfig to corenet64_smp_defconfig
Rather than trying to use the core name we use corenet to distinquish
the platform/core combo. corenet64 will be a 64-bit kernel build and
we'll add a new defconfig for corenet32 for a 32-bit platforms.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Michael Neuling [Sun, 5 Jun 2011 16:48:47 +0000 (16:48 +0000)]
powerpc: Fix doorbell type shift
doorbell type is defined as bits 32:36 so should be shifted by 63-36 =
27 rather than 28.
We never noticed this bug as we've only every used type PPC_DBELL = 0.
Signed-off-by: Michael Neuling <mikey@neuling.org> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul Mackerras [Wed, 25 May 2011 23:34:12 +0000 (23:34 +0000)]
powerpc: Avoid extra indirect function call in sending IPIs
On many platforms (including pSeries), smp_ops->message_pass is always
smp_muxed_ipi_message_pass. This changes arch/powerpc/kernel/smp.c so
that if smp_ops->message_pass is NULL, it calls smp_muxed_ipi_message_pass
directly.
This means that a platform doesn't need to set both .message_pass and
.cause_ipi, only one of them. It is a slight performance improvement
in that it gets rid of an indirect function call at the expense of a
predictable conditional branch.
Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Matt Evans [Wed, 25 May 2011 18:09:12 +0000 (18:09 +0000)]
powerpc: Fix early boot accounting of CPUs
smp_release_cpus() waits for all cpus (including the bootcpu) due to an
off-by-one count on boot_cpu_count (which is all CPUs). This patch replaces
that with spinning_secondaries (which is all secondary CPUs).
Signed-off-by: Matt Evans <matt@ozlabs.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds [Wed, 8 Jun 2011 22:18:19 +0000 (15:18 -0700)]
vfs: reorganize 'struct inode' layout a bit
This tries to make the 'struct inode' accesses denser in the data cache
by moving a commonly accessed field (i_security) closer to other fields
that are accessed often.
It also makes 'i_state' just an 'unsigned int' rather than 'unsigned
long', since we only use a few bits of that field, and moves it next to
the existing 'i_flags' so that we potentially get better structure
layout (although depending on config options, i_flags may already have
packed in the same word as i_lock, so this improves packing only for the
case of spinlock debugging)
Out 'struct inode' is still way too big, and we should probably move
some other fields around too (the acl fields in particular) for better
data cache access density. Other fields (like the inode hash) are
likely to be entirely irrelevant under most loads.
Linus Torvalds [Wed, 8 Jun 2011 22:11:56 +0000 (15:11 -0700)]
selinux: simplify and clean up inode_has_perm()
This is a rather hot function that is called with a potentially NULL
"struct common_audit_data" pointer argument. And in that case it has to
provide and initialize its own dummy common_audit_data structure.
However, all the _common_ cases already pass it a real audit-data
structure, so that uncommon NULL case not only creates a silly run-time
test, more importantly it causes that function to have a big stack frame
for the dummy variable that isn't even used in the common case!
So get rid of that stupid run-time behavior, and make the (few)
functions that currently call with a NULL pointer just call a new helper
function instead (naturally called inode_has_perm_noapd(), since it has
no adp argument).
This makes the run-time test be a static code generation issue instead,
and allows for a much denser stack since none of the common callers need
the dummy structure. And a denser stack not only means less stack space
usage, it means better cache behavior. So we have a win-win-win from
this simplification: less code executed, smaller stack footprint, and
better cache behavior.
Linus Torvalds [Wed, 8 Jun 2011 21:27:48 +0000 (14:27 -0700)]
Merge branch 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (28 commits)
MAINTAINERS: add a maintainer to Gadget Framework
USB: serial: add another 4N-GALAXY.DE PID to ftdi_sio driver
Revert "USB: option: add ID for ZTE MF 330"
drivers/usb/host/ohci-pxa27x.c: add missing clk_put
USB: CONFIG_USB_GADGET_DUALSPEED is not user-configurable
USB: dummy-hcd needs the has_tt flag
usb-storage: redo incorrect reads
usb/renesas_usbhs: free uep on removal
usb/s3c-hsudc: fix error path
usb/pxa25x_udc: cleanup the LUBBOCK err path
usb/mv_udc_core: fix compile
usb: gadget: include <linux/prefetch.h> to fix compiling error
USB: s3c-hsotg: Tone down debugging
usb: remove bad dput after dentry_unhash
USB: core: Tolerate protocol stall during hub and port status read
musb: fix prefetch build failure
USB: cdc-acm: Adding second ACM channel support for Nokia E7 and C7
usb-gadget: unlock data->lock mutex on error path in ep_write()
USB: option Add blacklist for ZTE K3765-Z (19d2:2002)
option: add Prolink PH300 modem IDs
...
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: trivial: add space in fsc error message
cifs: silence printk when establishing first session on socket
CIFS ACL support needs CONFIG_KEYS, so depend on it
possible memory corruption in cifs_parse_mount_options()
cifs: make CIFS depend on CRYPTO_ECB
cifs: fix the kernel release version in the default security warning message
spi/rtc-m41t93: Use spi_get_drvdata() for SPI devices
One new offender detected by the recently increased type checking in
platform_get_drvdata():
drivers/rtc/rtc-m41t93.c: In function ‘m41t93_remove’:
drivers/rtc/rtc-m41t93.c:192: warning: passing argument 1 of ‘platform_get_drvdata’ from incompatible pointer type
Use spi_get_drvdata() instead of platform_get_drvdata(), cfr. commit 42fea15d6dc410e62dac6a764142045280624a5b ("spi/rtc-{ds1390,ds3234,m41t94}:
Use spi_get_drvdata() for SPI devices")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Linus Torvalds [Wed, 8 Jun 2011 19:03:37 +0000 (12:03 -0700)]
Merge branch 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: off by one errors in multicalls.c
xen: use the trigger info we already have to choose the irq handler
Linus Torvalds [Wed, 8 Jun 2011 15:36:15 +0000 (08:36 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Fix comments in include/linux/perf_event.h
perf: Comment /proc/sys/kernel/perf_event_paranoid to be part of user ABI
perf python: Fix argument name list of read_on_cpu()
perf evlist: Don't die if sample_{id_all|type} is invalid
perf python: Use exception to propagate errors
perf evlist: Remove dependency on debug routines
perf, cgroups: Fix up for new API
Linus Torvalds [Wed, 8 Jun 2011 15:21:48 +0000 (08:21 -0700)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] soc_camera: preserve const attribute
[media] uvc_entity: initialize return value
[media] media: Fix media device minor registration
[media] Make nchg variable signed because the code compares this variable against negative values
[media] omap3isp: fix compiler warning
[media] v4l: Fix media_entity_to_video_device macro argument name
[media] ivtv: Internally separate encoder & decoder standard setting
[media] ivtvfb: Add sanity check to ivtvfb_pan_display()
[media] ivtvfb: use display information in info not in var for panning
[media] ivtv: Make two ivtv_msleep_timeout calls uninterruptable
[media] anysee: return EOPNOTSUPP for unsupported I2C messages
[media] gspca - ov519: Set the default frame rate to 15 fps
[media] gspca - stv06xx: Set a lower default value of gain for hdcs sensors
[media] gspca: Remove coarse_expo_autogain.h
[media] gspca - ov519: Change the ovfx2 bulk transfer size
[media] gspca - ov519: Fix a regression for ovfx2 webcams
Linus Torvalds [Wed, 8 Jun 2011 15:19:14 +0000 (08:19 -0700)]
Merge branch 'drm-radeon-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-radeon-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: disable hdmi audio by default
drm/radeon/kms: fix for radeon on systems >4GB without hardware iommu
drm/radeon/kms: set family for use in parser.
Linus Torvalds [Wed, 8 Jun 2011 14:46:30 +0000 (07:46 -0700)]
tty_buffer: get rid of 'seen_tail' logic in flush_to_ldisc
The flush_to_ldisc() work entry has special logic to notice when it has
seen the original tail of the data queue, and it avoids continuing the
flush if it sees that _original_ tail rather than the current tail.
This logic can trigger in case somebody is constantly adding new data to
the tty while the flushing is active - and the intent is to avoid
excessive CPU usage while flushing the tty, especially as we used to do
this from a softirq context which made it non-preemptible.
However, since we no longer re-arm the work-queue from within itself
(because that causes other trouble: see commit a5660b41af6a "tty: fix
endless work loop when the buffer fills up"), this just leads to
possible hung tty's (most easily seen in SMP and with a test-program
that floods a pty with data - nobody seems to have reported this for any
real-life situation yet).
And since the workqueue isn't done from timers and softirq's any more,
it's doubtful whether the CPU useage issue is really relevant any more.
So just remove the logic entirely, and see if anybody ever notices.
Alternatively, we might want to re-introduce the "re-arm the work" for
just this case, but then we'd have to re-introduce the delayed work
model or some explicit timer, which really doesn't seem worth it for
this.
Reported-and-tested-by: Guillaume Chazarain <guichaz@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Felipe Balbi <balbi@ti.com> Cc: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alex Deucher [Mon, 6 Jun 2011 21:39:16 +0000 (17:39 -0400)]
drm/radeon/kms: disable hdmi audio by default
The current RE'd code causes blank screens and
display problems on a lot of systems. So disable
it by default for now. It can still be enabled
by setting the audio parameter to 1. E.g.:
radeon.audio=1
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=38010
https://bugs.freedesktop.org/show_bug.cgi?id=27731
https://bugs.freedesktop.org/show_bug.cgi?id=35970
https://bugs.freedesktop.org/show_bug.cgi?id=26195
and many other reported problems.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel Haid [Wed, 8 Jun 2011 10:04:45 +0000 (20:04 +1000)]
drm/radeon/kms: fix for radeon on systems >4GB without hardware iommu
On my x86_64 system with >4GB of ram and swiotlb instead of
a hardware iommu (because I have a VIA chipset), the call
to pci_set_dma_mask (see below) with 40bits returns an error.
But it seems that the radeon driver is designed to have
need_dma32 = true exactly if pci_set_dma_mask is called
with 32 bits and false if it is called with 40 bits.
I have read somewhere that the default are 32 bits. So if the
call fails I suppose that need_dma32 should be set to true.
And indeed the patch fixes the problem I have had before
and which I had described here:
http://choon.net/forum/read.php?21,106131,115940
Acked-by: Alex Deucher <alexdeucher@gmail.com>
cc: stable@kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Wed, 8 Jun 2011 02:20:53 +0000 (19:20 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/amd-iommu: Fix boot crash with hidden PCI devices
x86/amd-iommu: Use only per-device dma_ops
x86/amd-iommu: Fix 3 possible endless loops
Linus Torvalds [Wed, 8 Jun 2011 02:09:26 +0000 (19:09 -0700)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/nv40: fall back to paged dma object for the moment
drm/nouveau: fix leak of gart mm node
drm/nouveau: fix vram page mapping when crossing page table boundaries
drm/nv17-nv40: Fix modesetting failure when pitch == 4096px (fdo bug 35901).
drm/nouveau: don't create accel engine objects when noaccel=1
drm/nvc0: recognise 0xdX chipsets as NV_C0
drm/i915: Add a no lvds quirk for the Asus EeeBox PC EB1007
drm/i915: Share the common force-audio property between connectors
drm/i915: Remove unused enum "chip_family"
drm/915: fix relaxed tiling on gen2: tile height
drm/i915/crt: Explicitly return false if connected to a digital monitor
drm/i915: Replace ironlake_compute_wm0 with g4x_compute_wm0
drm/i915: Only print out the actual number of fences for i915_error_state
drm/i915: s/addr & ~PAGE_MASK/offset_in_page(addr)/
drm: i915: correct return status in intel_hdmi_mode_valid()
drm/i915: fix regression after clock gating init split
drm/i915: fix if statement in ivybridge irq handler
Linus Torvalds [Wed, 8 Jun 2011 02:09:17 +0000 (19:09 -0700)]
Merge branch 'drm-radeon-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-radeon-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms/atom: fix PHY init
drm/radeon/kms: add missing Evergreen texture formats to the CS parser
drm/radeon/kms: viewport height has to be even
drm/radeon/kms: remove duplicate reg from r600 safe regs
drm/radeon/kms: add support for Llano Fusion APUs
drm/radeon/kms: add llano pci ids
drm/radeon/kms: fill in asic struct for llano
drm/radeon/kms: add family ids for llano APUs
drm/radeon: fix oops in ttm reserve when pageflipping (v2)
drm/radeon/kms: clean up the radeon kms Kconfig
drm/radeon/kms: fix thermal sensor reading on juniper
drm/radeon/kms: add missing case for cayman thermal sensor
drm/radeon/kms: add blit support for cayman (v2)
drm/radeon/kms/blit: workaround some hw issues on evergreen+
Linus Torvalds [Wed, 8 Jun 2011 02:07:22 +0000 (19:07 -0700)]
Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: Consider slack value in mod_timer()
clockevents: Handle empty cpumask gracefully
Linus Torvalds [Wed, 8 Jun 2011 02:06:28 +0000 (19:06 -0700)]
Merge branch 'kvm-updates/3.0' of git://git.kernel.org/pub/scm/virt/kvm/kvm
* 'kvm-updates/3.0' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Initialize kvm before registering the mmu notifier
KVM: x86: use proper port value when checking io instruction permission
KVM: add missing void __user * cast to access_ok() call
Grant Likely [Mon, 6 Jun 2011 06:40:48 +0000 (00:40 -0600)]
MAINTAINERS: Saying goodbye to David Brownell
We had to say goodbye when David passed away recently. David had a
huge impact on our community, both personally in the lives of the
people he worked with, and technically in the design and maintenance
of several subsystems. He is greatly missed.
He also leaves behind a number of much loved subsystems now orphaned.
This patch updates the MAINTAINERS file for the areas that David was
responsible for and adds an entry for him to the CREDITS file.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Harry Wei <harryxiyou@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Mon, 6 Jun 2011 14:47:14 +0000 (15:47 +0100)]
MN10300: die_if_no_fixup() shouldn't use get_user() as it doesn't call set_fs()
die_if_no_fixup() shouldn't use get_user() as it doesn't call set_fs() to
indicate that it wants to probe a kernel address. Instead it should use
probe_kernel_read().
This fixes the problem of gdb seeing SIGILL rather than SIGTRAP when hitting
the KGDB special breakpoint upon SysRq+g being seen. The problem was that
die_if_no_fixup() was failing to read the opcode of the instruction that caused
the exception, and thus not fixing up the exception.
This caused gdb to get a S04 response to the $? request in its remote protocol
rather than S05 - which would then cause it to continue with $C04 rather than
$c in an attempt to pass the signal onto the inferior process. The kernel,
however, does not support $Cnn, and so objects by returning an E22 response,
indicating an error. gdb does not expect this and prints:
warning: Remote failure reply: E22
and then returns to the gdb command prompt unable to continue.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Mon, 6 Jun 2011 14:47:05 +0000 (15:47 +0100)]
MN10300: Fix one of the kernel debugger cacheflush variants
One of the kernel debugger cacheflush variants escaped proper testing. Two of
the labels are wrong, being derived from the code that was copied to construct
the variant.
The first label results in the following assembler message:
AS arch/mn10300/mm/cache-dbg-flush-by-reg.o
arch/mn10300/mm/cache-dbg-flush-by-reg.S: Assembler messages:
arch/mn10300/mm/cache-dbg-flush-by-reg.S:123: Error: symbol `debugger_local_cache_flushinv_no_dcache' is already defined
And the second label results in the following linker message:
arch/mn10300/mm/built-in.o:(.text+0x1d39): undefined reference to `mn10300_local_icache_inv_range_reg_end'
arch/mn10300/mm/built-in.o:(.text+0x1d39): relocation truncated to fit: R_MN10300_PCREL16 against undefined symbol `mn10300_local_icache_inv_range_reg_end'
To test this file the following configuration pieces must be set:
Linus Torvalds [Wed, 8 Jun 2011 01:46:37 +0000 (18:46 -0700)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (21 commits)
ARM: OMAP4: MMC: increase delay for pbias
arm: omap2plus: move NAND_BLOCK_SIZE out of boards
omap4: hwmod: Enable the keypad
omap3: Free Beagle rev gpios when they are read, so others can read them later
arm: omap3: beagle: Ensure msecure is mux'd to be able to set the RTC
omap: rx51: Don't power up speaker amplifier at bootup
omap: rx51: Set regulator V28_A always on
ARM: OMAP4: MMC: no regulator off during probe for eMMC
arm: omap2plus: fix ads7846 pendown gpio request
ARM: OMAP2: Add missing iounmap in omap4430_phy_init
ARM: omap4: Pass core and wakeup mux tables to omap4_mux_init
ARM: omap2+: mux: Allow board mux settings to be NULL
OMAP4: fix return value of omap4_l3_init
OMAP: iovmm: fix SW flags passed by user
arch/arm/mach-omap1/dma.c: Invert calls to platform_device_put and platform_device_del
OMAP2+: mux: fix compilation warnings
OMAP: SRAM: Fix warning: format '%08lx' expects type 'long unsigned int'
arm: omap3: cm-t3517: fix section mismatch warning
OMAP2+: Fix 9 section mismatch(es) warnings from mach-omap2/built-in.o
ARM: OMAP2: Add missing include of linux/gpio.h
...
Linus Torvalds [Wed, 8 Jun 2011 01:36:59 +0000 (18:36 -0700)]
Merge branch 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
vfs: make unlink() and rmdir() return ENOENT in preference to EROFS
lmLogOpen() broken failure exit
usb: remove bad dput after dentry_unhash
more conservative S_NOSEC handling
PM / Runtime: Fix loops in pm_runtime_clk_notify()
The loops over connection ID strings in pm_runtime_clk_notify()
should actually iterate over the strings and not over the elements
of the first of them, so make them behave as appropriate.
This fixes a regression introduced by commit 600b776eb39a13a28b090
(OMAP1 / PM: Use generic clock manipulation routines for runtime PM).
Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The Samsung GPIO drivers are always built-in when the relevant
platform is selected. Change the Kconfig symbol to def_bool y
dependant on the platform.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
PM / Intel IOMMU: Fix init_iommu_pm_ops() for CONFIG_PM unset
If CONFIG_PM is not set, init_iommu_pm_ops() introduced by commit 134fac3f457f3dd753ecdb25e6da3e5f6629f696 (PCI / Intel IOMMU: Use
syscore_ops instead of sysdev class and sysdev) is not defined
appropriately. Fix this issue.
Reported-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Thomas Abraham [Tue, 7 Jun 2011 08:34:49 +0000 (14:04 +0530)]
gpio/exynos4: Fix incorrect mapping of gpio pull-up macro to register setting
The S3C_GPIO_PULL_UP macro value incorrectly maps to a reserved setting of GPIO
pull up/down registers on Exynos4 platform. Fix this incorrect mapping by adding
wrappers to the s3c_gpio_setpull_updown and s3c_gpio_getpull_updown functions.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
e1 = clk_get@p1(...);
... when != e1 = e2
when != clk_put(e1)
when any
if (...) { ... when != clk_put(e1)
when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
} else S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 7 Jun 2011 15:31:05 +0000 (11:31 -0400)]
USB: CONFIG_USB_GADGET_DUALSPEED is not user-configurable
This patch (as1468) changes the Kconfig definition for
USB_GADGET_DUALSPEED. This option is determined entirely by which
device controller drivers are to be built, through Select statements;
it does not need to be (and should not be) configurable by the user.
Also, the "default n" line is superfluous -- everything defaults to N.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 7 Jun 2011 15:33:01 +0000 (11:33 -0400)]
USB: dummy-hcd needs the has_tt flag
Like with other host controllers capable of operating at both high
speed and full speed, we need to indicate that the emulated controller
presented by dummy-hcd has this ability. Otherwise usbcore will not
accept full-speed gadgets under dummy-hcd. This patch (as1469) sets
the appropriate has_tt flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 7 Jun 2011 15:35:52 +0000 (11:35 -0400)]
usb-storage: redo incorrect reads
Some USB mass-storage devices have bugs that cause them not to handle
the first READ(10) command they receive correctly. The Corsair
Padlock v2 returns completely bogus data for its first read (possibly
it returns the data in encrypted form even though the device is
supposed to be unlocked). The Feiya SD/SDHC card reader fails to
complete the first READ(10) command after it is plugged in or after a
new card is inserted, returning a status code that indicates it thinks
the command was invalid, which prevents the kernel from retrying the
read.
Since the first read of a new device or a new medium is for the
partition sector, the kernel is unable to retrieve the device's
partition table. Users have to manually issue an "hdparm -z" or
"blockdev --rereadpt" command before they can access the device.
This patch (as1470) works around the problem. It adds a new quirk
flag, US_FL_INVALID_READ10, indicating that the first READ(10) should
always be retried immediately, as should any failing READ(10) commands
(provided the preceding READ(10) command succeeded, to avoid getting
stuck in a loop). The patch also adds appropriate unusual_devs
entries containing the new flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Sven Geggus <sven-usbst@geggus.net> Tested-by: Paul Hartman <paul.hartman+linux@gmail.com> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> CC: <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Theodore Ts'o [Mon, 6 Jun 2011 23:19:40 +0000 (19:19 -0400)]
vfs: make unlink() and rmdir() return ENOENT in preference to EROFS
If user space attempts to remove a non-existent file or directory, and
the file system is mounted read-only, return ENOENT instead of EROFS.
Either error code is arguably valid/correct, but ENOENT is a more
specific error message.
Reported-by: Michael Tokarev <mjt@tls.msk.ru> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sun, 5 Jun 2011 18:22:56 +0000 (19:22 +0100)]
lmLogOpen() broken failure exit
Callers of lmLogOpen() expect it to return -E... on failure exits, which
is what it returns, except for the case of blkdev_get_by_dev() failure.
It that case lmLogOpen() return the error with the wrong sign...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Peter Zijlstra [Fri, 3 Jun 2011 15:37:07 +0000 (17:37 +0200)]
sched: Fix/clarify set_task_cpu() locking rules
Sergey reported a CONFIG_PROVE_RCU warning in push_rt_task where
set_task_cpu() was called with both relevant rq->locks held, which
should be sufficient for running tasks since holding its rq->lock
will serialize against sched_move_task().
Update the comments and fix the task_group() lockdep test.
Peter Zijlstra [Mon, 6 Jun 2011 10:32:43 +0000 (12:32 +0200)]
lockdep: Fix lock_is_held() on recursion
The main lock_is_held() user is lockdep_assert_held(), avoid false
assertions in lockdep_off() sections by unconditionally reporting the
lock is taken.
[ the reason this is important is a lockdep_assert_held() in ttwu()
which triggers a warning under lockdep_off() as in printk() which
can trigger another wakeup and lock up due to spinlock
recursion, as reported and heroically debugged by Arne Jansen ]
Reported-and-tested-by: Arne Jansen <lists@die-jansens.de> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: <stable@kernel.org> Link: http://lkml.kernel.org/r/1307398759.2497.966.camel@laptop Signed-off-by: Ingo Molnar <mingo@elte.hu>
Joerg Roedel [Mon, 6 Jun 2011 14:50:14 +0000 (16:50 +0200)]
x86/amd-iommu: Fix boot crash with hidden PCI devices
Some PCIe cards ship with a PCI-PCIe bridge which is not
visible as a PCI device in Linux. But the device-id of the
bridge is present in the IOMMU tables which causes a boot
crash in the IOMMU driver.
This patch fixes by removing these cards from the IOMMU
handling. This is a pure -stable fix, a real fix to handle
this situation appriatly will follow for the next merge
window.
projects / mirror_ubuntu-focal-kernel.git / log