When tcmu_vma_fault() gets a page successfully, before the current context
completes page fault procedure, find_free_blocks() may run and call
unmap_mapping_range() to unmap the page. Assume that when
find_free_blocks() initially completes and the previous page fault
procedure starts to run again and completes, then one truncated page has
been mapped to userspace. But note that tcmu_vma_fault() has gotten a
refcount for the page so any other subsystem won't be able to use the page
unless the userspace address is unmapped later.
If another command subsequently runs and needs to extend dbi_thresh it may
reuse the corresponding slot for the previous page in data_bitmap. Then
though we'll allocate new page for this slot in data_area, no page fault
will happen because we have a valid map and the real request's data will be
lost.
Filesystem implementations will also run into this issue but they usually
lock the page when vm_operations_struct->fault gets a page and unlock the
page after finish_fault() completes. For truncate filesystems lock pages in
truncate_inode_pages() to protect against racing wrt. page faults.
To fix this possible data corruption scenario we can apply a method similar
to the filesystems. For pages that are to be freed, tcmu_blocks_release()
locks and unlocks. Make tcmu_vma_fault() also lock found page under
cmdr_lock. At the same time, since tcmu_vma_fault() gets an extra page
refcount, tcmu_blocks_release() won't free pages if pages are in page fault
procedure, which means it is safe to call tcmu_blocks_release() before
unmap_mapping_range().
With these changes tcmu_blocks_release() will wait for all page faults to
be completed before calling unmap_mapping_range(). And later, if
unmap_mapping_range() is called, it will ensure stale mappings are removed.
Link: https://lore.kernel.org/r/20220421023735.9018-1-xiaoguang.wang@linux.alibaba.com Reviewed-by: Bodo Stroesser <bostroesser@gmail.com> Signed-off-by: Xiaoguang Wang <xiaoguang.wang@linux.alibaba.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If a compat process tries to execute an unknown system call above the
__ARM_NR_COMPAT_END number, the kernel sends a SIGILL signal to the
offending process. Information about the error is printed to dmesg in
compat_arm_syscall() -> arm64_notify_die() -> arm64_force_sig_fault() ->
arm64_show_signal().
arm64_show_signal() interprets a non-zero value for
current->thread.fault_code as an exception syndrome and displays the
message associated with the ESR_ELx.EC field (bits 31:26).
current->thread.fault_code is set in compat_arm_syscall() ->
arm64_notify_die() with the bad syscall number instead of a valid ESR_ELx
value. This means that the ESR_ELx.EC field has the value that the user set
for the syscall number and the kernel can end up printing bogus exception
messages*. For example, for the syscall number 0x68000000, which evaluates
to ESR_ELx.EC value of 0x1A (ESR_ELx_EC_FPAC) the kernel prints this error:
which is misleading, as the bad compat syscall has nothing to do with
pointer authentication.
Stop arm64_show_signal() from printing exception syndrome information by
having compat_arm_syscall() set the ESR_ELx value to 0, as it has no
meaning for an invalid system call number. The example above now becomes:
which although shows less information because the syscall number,
wrongfully advertised as the ESR value, is missing, it is better than
showing plainly wrong information. The syscall number can be easily
obtained with strace.
*A 32-bit value above or equal to 0x8000_0000 is interpreted as a negative
integer in compat_arm_syscal() and the condition scno < __ARM_NR_COMPAT_END
evaluates to true; the syscall will exit to userspace in this case with the
ENOSYS error code instead of arm64_notify_die() being called.
Signed-off-by: Alexandru Elisei <alexandru.elisei@arm.com> Reviewed-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20220425114444.368693-3-alexandru.elisei@arm.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Double free crash is observed when FW recovery(caused by wmi
timeout/crash) is followed by immediate suspend event. The FW recovery
is triggered by ath10k_core_restart() which calls driver clean up via
ath10k_halt(). When the suspend event occurs between the FW recovery,
the restart worker thread is put into frozen state until suspend completes.
The suspend event triggers ath10k_stop() which again triggers ath10k_halt()
The double invocation of ath10k_halt() causes ath10k_htt_rx_free() to be
called twice(Note: ath10k_htt_rx_alloc was not called by restart worker
thread because of its frozen state), causing the crash.
To fix this, during the suspend flow, skip call to ath10k_halt() in
ath10k_stop() when the current driver state is ATH10K_STATE_RESTARTING.
Also, for driver state ATH10K_STATE_RESTARTING, call
ath10k_wait_for_suspend() in ath10k_stop(). This is because call to
ath10k_wait_for_suspend() is skipped later in
[ath10k_halt() > ath10k_core_stop()] for the driver state
ATH10K_STATE_RESTARTING.
The frozen restart worker thread will be cancelled during resume when the
device comes out of suspend.
Reported-by: kernel test robot <lkp@intel.com> CC: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
While the check for format_count > 64 in __drm_universal_plane_init()
shouldn't be hit (it's a WARN_ON), in its current position it will then
leak the plane->format_types array and fail to call
drm_mode_object_unregister() leaking the modeset identifier. Move it to
the start of the function to avoid allocating those resources in the
first place.
Signed-off-by: Steven Price <steven.price@arm.com> Signed-off-by: Liviu Dudau <liviu.dudau@arm.com> Link: https://lore.kernel.org/dri-devel/20211203102815.38624-1-steven.price@arm.com/ Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Add a quirk for the HP Pro Tablet 408, this BYTCR tablet has no CHAN
package in its ACPI tables and uses SSP0-AIF1 rather then SSP0-AIF2 which
is the default for BYTCR devices.
It also uses DMIC1 for the internal mic rather then the default IN3
and it uses JD2 rather then the default JD1 for jack-detect.
Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/1649396345-349-1-git-send-email-quic_haric@quicinc.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If no handler is found in lpfc_complete_unsol_iocb() to match the rctl of a
received frame, the frame is dropped and resources are leaked.
Fix by returning resources when discarding an unhandled frame type. Update
lpfc_fc_frame_check() handling of NOP basic link service.
Link: https://lore.kernel.org/r/20220426181419.9154-1-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync() and
pm_runtime_put_noidle(). This change is just to simplify the code, no
actual functional changes.
Link: https://lore.kernel.org/r/20220420090353.2588804-1-chi.minghao@zte.com.cn Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This patch fixes the issue where the driver miscomputes the 64-bit
values of the wptr of the SDMA doorbell when initializing the
hardware. SDMA engines v4 and later on have full 64-bit registers for
wptr thus they should be set properly.
Older generation hardwares like CIK / SI have only 16 / 20 / 24bits
for the WPTR, where the calls of lower_32_bits() will be removed in a
following patch.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Haohui Mai <ricetons@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If major equals 0, register_chrdev() returns an error code when it fails.
This function dynamically allocates a major and returns its number on
success, so we should use "< 0" to check it instead of "!".
Link: https://lore.kernel.org/r/20220418105755.2558828-1-lv.ruyi@zte.com.cn Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The ARASAN MMC controller on Keystone 3 class of devices need the SDCD
line to be connected for proper functioning. Similar to the issue pointed
out in sdhci-of-arasan.c driver, commit 3794c542641f ("mmc:
sdhci-of-arasan: Set controller to test mode when no CD bit").
In cases where this can't be connected, add a quirk to force the
controller into test mode and set the TESTCD bit. Use the flag
"ti,fails-without-test-cd", to implement this above quirk when required.
Do what is done in other DMA-enabled MMC host drivers (cf. host/mmci.c) and
limit the maximum segment size based on the DMA engine's capabilities. This
is needed to avoid warnings like the following with CONFIG_DMA_API_DEBUG=y.
If bitmap area contains invalid data, kernel will crash then mdadm
triggers "Segmentation fault".
This is cluster-md speical bug. In non-clustered env, mdadm will
handle broken metadata case. In clustered array, only kernel space
handles bitmap slot info. But even this bug only happened in clustered
env, current sanity check is wrong, the code should be changed.
In md_bitmap_read_sb (called by md_bitmap_create), bad bitmap magic didn't
block chunksize assignment, and zero value made DIV_ROUND_UP_SECTOR_T()
trigger "divide error".
When the driver fails to call the dma_set_mask(), the driver will get
the following splat:
[ 55.853884] BUG: KASAN: use-after-free in __process_removed_driver+0x3c/0x240
[ 55.854486] Read of size 8 at addr ffff88810de60408 by task modprobe/590
[ 55.856822] Call Trace:
[ 55.860327] __process_removed_driver+0x3c/0x240
[ 55.861347] bus_for_each_dev+0x102/0x160
[ 55.861681] i2c_del_driver+0x2f/0x50
This is because the driver has initialized the i2c related resources
in cx23885_dev_setup() but not released them in error handling, fix this
bug by modifying the error path that jumps after failing to call the
dma_set_mask().
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If venus_probe fails at pm_runtime_put_sync the error handling first
calls hfi_destroy and afterwards hfi_core_deinit. As hfi_destroy sets
core->ops to NULL, hfi_core_deinit cannot call the core_deinit function
anymore.
Avoid this null pointer derefence by skipping the call when necessary.
This patch fixes an invalid TX PA DC bias level on QCA9561, which
results in a very low output power and very low throughput as devices
are further away from the AP (compared to other 2.4GHz APs).
This patch was suggested by Felix Fietkau, who noted[1]:
"The value written to that register is wrong, because while the mask
definition AR_CH0_TOP2_XPABIASLVL uses a different value for 9561, the
shift definition AR_CH0_TOP2_XPABIASLVL_S is hardcoded to 12, which is
wrong for 9561."
In real life testing, without this patch the 2.4GHz throughput on
Yuncore XD3200 is around 10Mbps sitting next to the AP, and closer to
practical maximum with the patch applied.
commit cfb7b8bf1e2d66 ("ASoC: rsnd: tidyup
rsnd_ssiu_busif_err_status_clear()") merged duplicate code, but it didn't
care about default case, and causes smatch warnings.
smatch warnings:
sound/soc/sh/rcar/ssiu.c:112 rsnd_ssiu_busif_err_status_clear() \
error: uninitialized symbol 'offset'.
sound/soc/sh/rcar/ssiu.c:114 rsnd_ssiu_busif_err_status_clear() \
error: uninitialized symbol 'shift'.
This patch cares it.
Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/87r15rgn6p.wl-kuninori.morimoto.gx@renesas.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In function si_parse_power_table(), array adev->pm.dpm.ps and its member
is allocated. If the allocation of each member fails, the array itself
is freed and returned with an error code. However, the array is later
freed again in si_dpm_fini() function which is called when the function
returns an error.
This leads to potential double free of the array adev->pm.dpm.ps, as
well as leak of its array members, since the members are not freed in
the allocation function and the array is not nulled when freed.
In addition adev->pm.dpm.num_ps, which keeps track of the allocated
array member, is not updated until the member allocation is
successfully finished, this could also lead to either use after free,
or uninitialized variable access in si_dpm_fini().
Fix this by postponing the free of the array until si_dpm_fini() and
increment adev->pm.dpm.num_ps everytime the array member is allocated.
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When PSCI OSI mode is supported the syscore flag is set for the CPU devices
that becomes attached to their PM domains (genpds). In the suspend-to-idle
case, we call dev_pm_genpd_suspend|resume() to allow genpd to properly
manage the power-off/on operations (pick an idlestate and manage the on/off
notifications).
For suspend-to-ram, dev_pm_genpd_suspend|resume() is currently not being
called, which causes a problem that the genpd on/off notifiers do not get
sent as expected. This prevents the platform-specific operations from being
executed, typically needed just before/after the boot CPU is being turned
off/on.
To deal with this problem, let's register a syscore ops for cpuidle-psci
when PSCI OSI mode is being used and call dev_pm_genpd_suspend|resume()
from them. In this way, genpd regains control of the PM domain topology and
then sends the on/off notifications when it's appropriate.
Reported-by: Maulik Shah <quic_mkshah@quicinc.com> Suggested-by: Maulik Shah <quic_mkshah@quicinc.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Maulik Shah <quic_mkshah@quicinc.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
this_cpu_ptr() calls smp_processor_id() in a preemptible context.
Fix by using per_cpu_ptr() with raw_smp_processor_id() instead.
Link: https://lore.kernel.org/r/20220412222008.126521-16-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fix by reordering the taking of the lpfc_cmd->buf_lock and phba->hbalock in
lpfc_abort_handler routine so that it tries to take the lpfc_cmd->buf_lock
first before phba->hbalock.
Link: https://lore.kernel.org/r/20220412222008.126521-7-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The same CPU tries to claim the phba->port_list_lock twice.
Move the cfg_log_verbose checks as part of the lpfc_printf_vlog() and
lpfc_printf_log() macros before calling lpfc_dmp_dbg(). There is no need
to take the phba->port_list_lock within lpfc_dmp_dbg().
Link: https://lore.kernel.org/r/20220412222008.126521-3-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
ICX (and its duplicates) require special hard-coded DRAM RAPL units,
rather than using the generic RAPL energy units.
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The direction field in the DMA config is deprecated. The rspi driver
sets {src,dst}_{addr,addr_width} based on the DMA direction and
it results in dmaengine_slave_config() failure as RZ DMAC driver
validates {src,dst}_addr_width values independent of DMA direction.
This patch fixes the issue by passing both {src,dst}_{addr,addr_width}
values independent of DMA direction.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Suggested-by: Vinod Koul <vkoul@kernel.org> Reviewed-by: Vinod Koul <vkoul@kernel.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20220411173115.6619-1-biju.das.jz@bp.renesas.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It is possible when using ASoC that input_dev is unregistered while
calling snd_jack_report, which causes NULL pointer dereference.
In order to prevent this serialize access to input_dev using mutex lock.
The TASKS_RUDE_RCU does not select IRQ_WORK, which can result in build
failures for kernels that do not otherwise select IRQ_WORK. This commit
therefore causes the TASKS_RUDE_RCU Kconfig option to select IRQ_WORK.
Reported-by: Hyeonggon Yoo <42.hyeyoo@gmail.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This commit therefore fixes this issue by applying a single-CPU
optimization to the RCU Tasks Rude grace-period process. The key point
here is that the purpose of this RCU flavor is to force a schedule on
each online CPU since some past event. But the rcu_tasks_rude_wait_gp()
function runs in the context of the RCU Tasks Rude's grace-period kthread,
so there must already have been a context switch on the current CPU since
the call to either synchronize_rcu_tasks_rude() or call_rcu_tasks_rude().
So if there is only a single CPU online, RCU Tasks Rude's grace-period
kthread does not need to anything at all.
It turns out that the rcu_tasks_rude_wait_gp() function's call to
schedule_on_each_cpu() causes problems during early boot. During that
time, there is only one online CPU, namely the boot CPU. Therefore,
applying this single-CPU optimization fixes early-boot instances of
this problem.
Link: https://lore.kernel.org/lkml/20220210184319.25009-1-treasure4paddy@gmail.com/T/ Suggested-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Padmanabha Srinivasaiah <treasure4paddy@gmail.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If drm_universal_plane_init() fails early we jump to the common cleanup code
that calls komeda_plane_destroy() which in turn could access the uninitalised
drm_plane and crash. Return early if an error is detected without going through
the common code.
Reported-by: Steven Price <steven.price@arm.com> Reviewed-by: Steven Price <steven.price@arm.com> Signed-off-by: Liviu Dudau <liviu.dudau@arm.com> Link: https://lore.kernel.org/dri-devel/20211203100946.2706922-1-liviu.dudau@arm.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Using an ath9k card the debugfs output of minstrel_ht looks like the following
(note the zero values for the first four rates sum-of success/attempts):
Total packet count:: ideal 16582 lookaround 885
Average # of aggregated frames per A-MPDU: 1.0
Debugging showed that the rate statistics for the first four rates where
stored in the MINSTREL_CCK_GROUP instead of the MINSTREL_OFDM_GROUP because
in minstrel_ht_get_stats() the supported check was not honoured as done in
various other places, e.g net/mac80211/rc80211_minstrel_ht_debugfs.c:
While running inside virtual machine, the kernel can bypass cache
flushing. Changing sleep state in a virtual machine doesn't affect the
host system sleep state and cannot lead to data loss.
Before entering sleep states, the ACPI code flushes caches to prevent
data loss using the WBINVD instruction. This mechanism is required on
bare metal.
But, any use WBINVD inside of a guest is worthless. Changing sleep
state in a virtual machine doesn't affect the host system sleep state
and cannot lead to data loss, so most hypervisors simply ignore it.
Despite this, the ACPI code calls WBINVD unconditionally anyway.
It's useless, but also normally harmless.
In TDX guests, though, WBINVD stops being harmless; it triggers a
virtualization exception (#VE). If the ACPI cache-flushing WBINVD
were left in place, TDX guests would need handling to recover from
the exception.
Avoid using WBINVD whenever running under a hypervisor. This both
removes the useless WBINVDs and saves TDX from implementing WBINVD
handling.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20220405232939.73860-30-kirill.shutemov@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The UV5 platform synchronizes the TSCs among all chassis, and will not
proceed to OS boot without achieving synchronization. Previous UV
platforms provided a register indicating successful synchronization.
This is no longer available on UV5. On this platform TSC_ADJUST
should not be reset by the kernel.
Signed-off-by: Mike Travis <mike.travis@hpe.com> Signed-off-by: Steve Wahl <steve.wahl@hpe.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Dimitri Sivanich <dimitri.sivanich@hpe.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20220406195149.228164-3-steve.wahl@hpe.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This shouldn't be a problem in practice since until we've actually
taken over the console there's nothing we've registered with the
console/vt subsystem, so the exit/unbind path that check this can't
do the wrong thing. But it's confusing, so fix it by moving it a tad
later.
Acked-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Du Cheng <ducheng2@gmail.com> Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: Claudio Suarez <cssk@net-c.es> Cc: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220405210335.3434130-14-daniel.vetter@ffwll.ch Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
idev->addr_list needs to be protected by idev->lock. However, it is not
always possible to do so while iterating and performing actions on
inet6_ifaddr instances. For example, multiple functions (like
addrconf_{join,leave}_anycast) eventually call down to other functions
that acquire the idev->lock. The current code temporarily unlocked the
idev->lock during the loops, which can cause race conditions. Moving the
locks up is also not an appropriate solution as the ordering of lock
acquisition will be inconsistent with for example mc_lock.
This solution adds an additional field to inet6_ifaddr that is used
to temporarily add the instances to a temporary list while holding
idev->lock. The temporary list can then be traversed without holding
idev->lock. This change was done in two places. In addrconf_ifdown, the
list_for_each_entry_safe variant of the list loop is also no longer
necessary as there is no deletion within that specific loop.
Suggested-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Niels Dossche <dossche.niels@gmail.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Link: https://lore.kernel.org/r/20220403231523.45843-1-dossche.niels@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
crypt and crypt->ops could be null, so we need to checking null
before dereference
Signed-off-by: Haowen Bai <baihaowen@meizu.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/1648797055-25730-1-git-send-email-baihaowen@meizu.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
fix warning reported by smatch:
drivers/net/wireless/broadcom/b43/phy_n.c:585 b43_nphy_adjust_lna_gain_table()
warn: assigning (-2) to unsigned variable '*(lna_gain[0])'
Signed-off-by: Haowen Bai <baihaowen@meizu.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/1648203315-28093-1-git-send-email-baihaowen@meizu.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
fix warning reported by smatch:
drivers/net/wireless/broadcom/b43legacy/phy.c:1181 b43legacy_phy_lo_b_measure()
warn: assigning (-772) to unsigned variable 'fval'
Signed-off-by: Haowen Bai <baihaowen@meizu.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/1648203433-8736-1-git-send-email-baihaowen@meizu.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
cfg80211_ch_switch_notify uses ASSERT_WDEV_LOCK to assert that
net_device->ieee80211_ptr->mtx (which is the same as priv->wdev.mtx)
is held during the function's execution.
mwifiex_dfs_chan_sw_work_queue is one of its callers, which does not
hold that lock, therefore violating the assertion.
Add a lock around the call.
Disclaimer:
I am currently working on a static analyser to detect missing locks.
This was a reported case. I manually verified the report by looking
at the code, so that I do not send wrong information or patches.
After concluding that this seems to be a true positive, I created
this patch.
However, as I do not in fact have this particular hardware,
I was unable to test it.
Reviewed-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Niels Dossche <dossche.niels@gmail.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220321225515.32113-1-dossche.niels@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The script for checking that various lists of types in bpftool remain in
sync with the UAPI BPF header uses a regex to parse enum bpf_prog_type.
If this enum contains a set of values different from the list of program
types in bpftool, it complains.
This script should have reported the addition, some time ago, of the new
BPF_PROG_TYPE_SYSCALL, which was not reported to bpftool's program types
list. It failed to do so, because it failed to parse that new type from
the enum. This is because the new value, in the BPF header, has an
explicative comment on the same line, and the regex does not support
that.
Let's update the script to support parsing enum values when they have
comments on the same line.
Since commit 6521f8917082 ("namei: prepare for idmapped mounts")
vfs_link's prototype was changed, the kprobe definition in
profiler selftest in turn wasn't updated. The result is that all
argument after the first are now stored in different registers. This
means that self-test has been broken ever since. Fix it by updating the
kprobe definition accordingly.
Signed-off-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Link: https://lore.kernel.org/bpf/20220331140949.1410056-1-nborisov@suse.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The kms code wasn't validating the modifiers and was letting through
unsupported formats. rgb8 was never properly supported and has no
matching svga screen target format so remove it.
This fixes format/modifier failures in kms_addfb_basic from IGT.
Signed-off-by: Zack Rusin <zackr@vmware.com> Reviewed-by: Martin Krastev <krastevm@vmware.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220318174332.440068-4-zack@kde.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The VT-d spec requires (10.4.4 Global Command Register, TE
field) that:
Hardware implementations supporting DMA draining must drain
any in-flight DMA read/write requests queued within the
Root-Complex before completing the translation enable
command and reflecting the status of the command through
the TES field in the Global Status register.
Unfortunately, some integrated graphic devices fail to do
so after some kind of power state transition. As the
result, the system might stuck in iommu_disable_translati
on(), waiting for the completion of TE transition.
This adds RPLS to a quirk list for those devices and skips
TE disabling if the qurik hits.
[BUG]
Test case generic/475 have a very high chance (almost 100%) to hit a fs
hang, where a data page will never be unlocked and hang all later
operations.
[CAUSE]
In btrfs_do_readpage(), if we hit an error from submit_extent_page() we
will try to do the cleanup for our current io range, and exit.
This works fine for PAGE_SIZE == sectorsize cases, but not for subpage.
For subpage btrfs_do_readpage() will lock the full page first, which can
contain several different sectors and extents:
btrfs_do_readpage()
|- begin_page_read()
| |- btrfs_subpage_start_reader();
| Now the page will have PAGE_SIZE / sectorsize reader pending,
| and the page is locked.
|
|- end_page_read() for different branches
| This function will reduce subpage readers, and when readers
| reach 0, it will unlock the page.
But when submit_extent_page() failed, we only cleanup the current
io range, while the remaining io range will never be cleaned up, and the
page remains locked forever.
[FIX]
Update the error handling of submit_extent_page() to cleanup all the
remaining subpage range before exiting the loop.
Please note that, now submit_extent_page() can only fail due to
sanity check in alloc_new_bio().
Thus regular IO errors are impossible to trigger the error path.
CC: stable@vger.kernel.org # 5.15+ Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
[BUG]
There is a report that a btrfs has a bad super block num devices.
This makes btrfs to reject the fs completely.
BTRFS error (device sdd3): super_num_devices 3 mismatch with num_devices 2 found here
BTRFS error (device sdd3): failed to read chunk tree: -22
BTRFS error (device sdd3): open_ctree failed
[CAUSE]
During btrfs device removal, chunk tree and super block num devs are
updated in two different transactions:
btrfs_rm_device()
|- btrfs_rm_dev_item(device)
| |- trans = btrfs_start_transaction()
| | Now we got transaction X
| |
| |- btrfs_del_item()
| | Now device item is removed from chunk tree
| |
| |- btrfs_commit_transaction()
| Transaction X got committed, super num devs untouched,
| but device item removed from chunk tree.
| (AKA, super num devs is already incorrect)
|
|- cur_devices->num_devices--;
|- cur_devices->total_devices--;
|- btrfs_set_super_num_devices()
All those operations are not in transaction X, thus it will
only be written back to disk in next transaction.
So after the transaction X in btrfs_rm_dev_item() committed, but before
transaction X+1 (which can be minutes away), a power loss happen, then
we got the super num mismatch.
This has been fixed by commit bbac58698a55 ("btrfs: remove device item
and update super block in the same transaction").
[FIX]
Make the super_num_devices check less strict, converting it from a hard
error to a warning, and reset the value to a correct one for the current
or next transaction commit.
As the number of device items is the critical information where the
super block num_devices is only a cached value (and also useful for
cross checking), it's safe to automatically update it. Other device
related problems like missing device are handled after that and may
require other means to resolve, like degraded mount. With this fix,
potentially affected filesystems won't fail mount and require the manual
repair by btrfs check.
Reported-by: Luca Béla Palkovics <luca.bela.palkovics@gmail.com> Link: https://lore.kernel.org/linux-btrfs/CA+8xDSpvdm_U0QLBAnrH=zqDq_cWCOH5TiV46CKmp3igr44okQ@mail.gmail.com/ CC: stable@vger.kernel.org # 4.14+ Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
[BUG]
If we hit an error from submit_extent_page() inside
__extent_writepage_io(), we could still return 0 to the caller, and
even trigger the warning in btrfs_page_assert_not_dirty().
[CAUSE]
In __extent_writepage_io(), if we hit an error from
submit_extent_page(), we will just clean up the range and continue.
This is completely fine for regular PAGE_SIZE == sectorsize, as we can
only hit one sector in one page, thus after the error we're ensured to
exit and @ret will be saved.
But for subpage case, we may have other dirty subpage range in the page,
and in the next loop, we may succeeded submitting the next range.
In that case, @ret will be overwritten, and we return 0 to the caller,
while we have hit some error.
[FIX]
Introduce @has_error and @saved_ret to record the first error we hit, so
we will never forget what error we hit.
CC: stable@vger.kernel.org # 5.15+ Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The following error message lack the "0x" obviously:
cannot mount because of unsupported optional features (4000)
Add the prefix to make it less confusing. This can happen on older
kernels that try to mount a filesystem with newer features so it makes
sense to backport to older trees.
CC: stable@vger.kernel.org # 4.14+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The current implementation of PTRACE_KILL is buggy and has been for
many years as it assumes it's target has stopped in ptrace_stop. At a
quick skim it looks like this assumption has existed since ptrace
support was added in linux v1.0.
While PTRACE_KILL has been deprecated we can not remove it as
a quick search with google code search reveals many existing
programs calling it.
When the ptracee is not stopped at ptrace_stop some fields would be
set that are ignored except in ptrace_stop. Making the userspace
visible behavior of PTRACE_KILL a noop in those case.
As the usual rules are not obeyed it is not clear what the
consequences are of calling PTRACE_KILL on a running process.
Presumably userspace does not do this as it achieves nothing.
Replace the implementation of PTRACE_KILL with a simple
send_sig_info(SIGKILL) followed by a return 0. This changes the
observable user space behavior only in that PTRACE_KILL on a process
not stopped in ptrace_stop will also kill it. As that has always
been the intent of the code this seems like a reasonable change.
Cc: stable@vger.kernel.org Reported-by: Al Viro <viro@zeniv.linux.org.uk> Suggested-by: Al Viro <viro@zeniv.linux.org.uk> Tested-by: Kees Cook <keescook@chromium.org> Reviewed-by: Oleg Nesterov <oleg@redhat.com> Link: https://lkml.kernel.org/r/20220505182645.497868-7-ebiederm@xmission.com Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
xtensa is the last user of the PT_SINGLESTEP flag. Changing tsk->ptrace in
user_enable_single_step and user_disable_single_step without locking could
potentiallly cause problems.
So use a thread info flag instead of a flag in tsk->ptrace. Use TIF_SINGLESTEP
that xtensa already had defined but unused.
Remove the definitions of PT_SINGLESTEP and PT_BLOCKSTEP as they have no more users.
Cc: stable@vger.kernel.org Acked-by: Max Filippov <jcmvbkbc@gmail.com> Tested-by: Kees Cook <keescook@chromium.org> Reviewed-by: Oleg Nesterov <oleg@redhat.com> Link: https://lkml.kernel.org/r/20220505182645.497868-4-ebiederm@xmission.com Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
User mode linux is the last user of the PT_DTRACE flag. Using the flag to indicate
single stepping is a little confusing and worse changing tsk->ptrace without locking
could potentionally cause problems.
So use a thread info flag with a better name instead of flag in tsk->ptrace.
Remove the definition PT_DTRACE as uml is the last user.
Cc: stable@vger.kernel.org Acked-by: Johannes Berg <johannes@sipsolutions.net> Tested-by: Kees Cook <keescook@chromium.org> Reviewed-by: Oleg Nesterov <oleg@redhat.com> Link: https://lkml.kernel.org/r/20220505182645.497868-3-ebiederm@xmission.com Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When the system runs out of enclave memory, SGX can reclaim EPC pages
by swapping to normal RAM. These backing pages are allocated via a
per-enclave shared memory area. Since SGX allows unlimited over
commit on EPC memory, the reclaimer thread can allocate a large
number of backing RAM pages in response to EPC memory pressure.
When the shared memory backing RAM allocation occurs during
the reclaimer thread context, the shared memory is charged to
the root memory control group, and the shmem usage of the enclave
is not properly accounted for, making cgroups ineffective at
limiting the amount of RAM an enclave can consume.
For example, when using a cgroup to launch a set of test
enclaves, the kernel does not properly account for 50% - 75% of
shmem page allocations on average. In the worst case, when
nearly all allocations occur during the reclaimer thread, the
kernel accounts less than a percent of the amount of shmem used
by the enclave's cgroup to the correct cgroup.
SGX stores a list of mm_structs that are associated with
an enclave. Pick one of them during reclaim and charge that
mm's memcg with the shmem allocation. The one that gets picked
is arbitrary, but this list almost always only has one mm. The
cases where there is more than one mm with different memcg's
are not worth considering.
Create a new function - sgx_encl_alloc_backing(). This function
is used whenever a new backing storage page needs to be
allocated. Previously the same function was used for page
allocation as well as retrieving a previously allocated page.
Prior to backing page allocation, if there is a mm_struct associated
with the enclave that is requesting the allocation, it is set
as the active memory control group.
[ dhansen: - fix merge conflict with ELDU fixes
- check against actual ksgxd_tsk, not ->mm ]
Cc: stable@vger.kernel.org Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Acked-by: Roman Gushchin <roman.gushchin@linux.dev> Link: https://lkml.kernel.org/r/20220520174248.4918-1-kristen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In crash_prepare_elf64_headers(), a buffer is allocated via vmalloc() to
store elf headers. While it's not freed back to system correctly when
kdump kernel is reloaded or unloaded. Then memory leak is caused. Fix it
by introducing x86 specific function arch_kimage_file_post_load_cleanup(),
and freeing the buffer there.
And also remove the incorrect elf header buffer freeing code. Before
calling arch specific kexec_file loading function, the image instance has
been initialized. So 'image->elf_headers' must be NULL. It doesn't make
sense to free the elf header buffer in the place.
Three different people have reported three bugs about the memory leak on
x86_64 inside Redhat.
Link: https://lkml.kernel.org/r/20220223113225.63106-2-bhe@redhat.com Signed-off-by: Baoquan He <bhe@redhat.com> Acked-by: Dave Young <dyoung@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
According to the latest event list, the event encoding 0x55
INST_DECODED.DECODERS and 0x56 UOPS_DECODED.DEC0 are only available on
the first 4 counters. Add them into the event constraints table.
Fixes: 6017608936c1 ("perf/x86/intel: Add Icelake support") Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Signed-off-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220525133952.1660658-1-kan.liang@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In mce_threshold_create_device(), if threshold_create_bank() fails, the
previously allocated threshold banks array @bp will be leaked because
the call to mce_threshold_remove_device() will not free it.
This happens because mce_threshold_remove_device() fetches the pointer
through the threshold_banks per-CPU variable but bp is written there
only after the bank creation is successful, and not before, when
threshold_create_bank() fails.
Add a helper which unwinds all the bank creation work previously done
and pass into it the previously allocated threshold banks array for
freeing.
[ bp: Massage. ]
Fixes: 6458de97fc15 ("x86/mce/amd: Straighten CPU hotplug path") Co-developed-by: Alviro Iskandar Setiawan <alviro.iskandar@gnuweeb.org> Signed-off-by: Alviro Iskandar Setiawan <alviro.iskandar@gnuweeb.org> Co-developed-by: Yazen Ghannam <yazen.ghannam@amd.com> Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com> Signed-off-by: Ammar Faizi <ammarfaizi2@gnuweeb.org> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20220329104705.65256-3-ammarfaizi2@gnuweeb.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
intel_hid_dsm_fn_mask is a bit mask containing one bit for each function
index. Fix the function index check in intel_hid_evaluate_method
accordingly, which was missed in commit 97ab4516205e ("platform/x86:
intel-hid: fix _DSM function index handling").
Fixes: 97ab4516205e ("platform/x86: intel-hid: fix _DSM function index handling") Cc: stable@vger.kernel.org Signed-off-by: Michael Niewöhner <linux@mniewoehner.de> Link: https://lore.kernel.org/r/66f813f5bcc724a0f6dd5adefe6a9728dbe509e3.camel@mniewoehner.de Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
as this is the only way to make sure the region is allocated.
Fix the conditional that was wrong and only tried to make already
non-sparse files non-sparse.
Cc: stable@vger.kernel.org Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Apparently we need to maintain these functions with
ntfs_get_acl_ex and ntfs_set_acl_ex.
This commit fixes xfstest generic/099 Fixes: 95dd8b2c1ed0 ("fs/ntfs3: Remove unnecessary functions") Reviewed-by: Kari Argillander <kari.argillander@gmail.com> Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We must check size before trying to allocate.
Size can be set for example by "ulimit -f".
Fixes xfstest generic/228 Fixes: 4342306f0f0d ("fs/ntfs3: Add file operations and implementation") Reviewed-by: Kari Argillander <kari.argillander@gmail.com> Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If size of file was reduced, we still kept allocated blocks.
This commit makes ntfs3 work as other fs like btrfs. Link: https://bugzilla.kernel.org/show_bug.cgi?id=214719 Fixes: 4342306f0f0d ("fs/ntfs3: Add file operations and implementation") Reported-by: Ganapathi Kamath <hgkamath@hotmail.com> Tested-by: Ganapathi Kamath <hgkamath@hotmail.com> Reviewed-by: Kari Argillander <kari.argillander@gmail.com> Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Two problems:
1. ntfs3_setattr can't truncate preallocated space;
2. if allocated fragment "cross" valid size, then fragment splits into two parts:
- normal part;
- unwritten part (here we must return FIEMAP_EXTENT_LAST).
Before this commit we returned FIEMAP_EXTENT_LAST for whole fragment.
Fixes xfstest generic/092 Fixes: 4342306f0f0d ("fs/ntfs3: Add file operations and implementation") Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Update valid size if write is still in I/O queue.
Fixes xfstest generic/240 Fixes: 82cae269cfa9 ("fs/ntfs3: Add initialization of super block") Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It has been observed with certain PCIe USB cards (like Inateck connected
to AM64 EVM or J7200 EVM) that as soon as the primary roothub is
registered, port status change is handled even before xHC is running
leading to cold plug USB devices not detected. For such cases, registering
both the root hubs along with the second HCD is required. Add support for
deferring roothub registration in usb_add_hcd(), so that both primary and
secondary roothubs are registered along with the second HCD.
This patch has been added and reverted earier as it triggered a race
in usb device enumeration.
That race is now fixed in 5.16-rc3, and in stable back to 5.4
commit 6cca13de26ee ("usb: hub: Fix locking issues with address0_mutex")
commit 6ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0
race")
CC: stable@vger.kernel.org # 5.4+ Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com> Tested-by: Chris Chiu <chris.chiu@canonical.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Link: https://lore.kernel.org/r/20220510091630.16564-2-kishon@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When dwc3_gadget_ep_cleanup_completed_requests() called to
dwc3_gadget_giveback() where the dwc3 lock is released, other thread is
able to execute. In this situation, usb_ep_disable() gets the chance to
clear endpoint descriptor pointer which leds to the null pointer
dereference problem. So needs to move the null pointer check to a proper
place.
Running the driver through kasan gives an interesting splat:
BUG: KASAN: global-out-of-bounds in isp1760_register+0x180/0x70c
Read of size 20 at addr f1db2e64 by task swapper/0/1
(...)
isp1760_register from isp1760_plat_probe+0x1d8/0x220
(...)
This happens because the loop reading the regmap fields for the
different ISP1760 variants look like this:
for (i = 0; i < HC_FIELD_MAX; i++) { ... }
Meaning it expects the arrays to be at least HC_FIELD_MAX - 1 long.
However the arrays isp1760_hc_reg_fields[], isp1763_hc_reg_fields[],
isp1763_hc_volatile_ranges[] and isp1763_dc_volatile_ranges[] are
dynamically sized during compilation.
Fix this by putting an empty assignment to the [HC_FIELD_MAX]
and [DC_FIELD_MAX] array member at the end of each array.
This will make the array one member longer than it needs to be,
but avoids the risk of overwriting whatever is inside
[HC_FIELD_MAX - 1] and is simple and intuitive to read. Also
add comments explaining what is going on.
Fixes: 1da9e1c06873 ("usb: isp1760: move to regmap for register access") Cc: stable@vger.kernel.org Cc: Rui Miguel Silva <rui.silva@linaro.org> Cc: Dietmar Eggemann <dietmar.eggemann@arm.com> Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20220516091424.391209-1-linus.walleij@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The BG95 modem has 3 USB configurations that are configurable via the AT
command AT+QCFGEXT="usbnet",["ecm"|"modem"|"rmnet"] which make the modem
enumerate with the following interfaces, respectively:
At closing a USB MIDI output substream, there might be still a pending
work, which would eventually access the rawmidi runtime object that is
being released. For fixing the race, make sure to cancel the pending
work at closing.
Set microphone pins 0x18 (rear) and 0x19 (front) to VREF_50 to fix the
microphone noise on ASUS TUF B550M-PLUS which uses the ALCS1200A codec.
The initial value was VREF_80.
The same issue is also present on Windows using both the default Windows
driver and all tested Realtek drivers before version 6.0.9049.1. Comparing
Realtek driver 6.0.9049.1 (the first one without the microphone noise) to
Realtek driver 6.0.9047.1 (the last one with the microphone noise)
revealed that the fix is the result of setting pins 0x18 and 0x19 to
VREF_50.
This fix may also work for other boards that have been reported to have
the same microphone issue and use the ALC1150 and ALCS1200A codecs, since
these codecs are similar and the fix in the Realtek driver on Windows is
common for both. However, it is currently enabled only for ASUS TUF
B550M-PLUS as this is the only board that could be tested.
The 2022-model XPS 15 appears to use the same 4-speakers-on-ALC289
audio setup as the Dell XPS 15 9510, so requires the same quirk to
enable woofer output. Tested on my own 9520.
[ Move the entry to the right position in the SSID order -- tiwai ]
After commit 49b290e430d3 ("riscv: prevent compressed instructions in
alternatives"), builds with LLVM's integrated assembler fail:
In file included from arch/riscv/mm/init.c:10:
In file included from ./include/linux/mm.h:29:
In file included from ./include/linux/pgtable.h:6:
In file included from ./arch/riscv/include/asm/pgtable.h:108:
./arch/riscv/include/asm/tlbflush.h:23:2: error: expected assembly-time absolute expression
ALT_FLUSH_TLB_PAGE(__asm__ __volatile__ ("sfence.vma %0" : : "r" (addr) : "memory"));
^
./arch/riscv/include/asm/errata_list.h:33:5: note: expanded from macro 'ALT_FLUSH_TLB_PAGE'
asm(ALTERNATIVE("sfence.vma %0", "sfence.vma", SIFIVE_VENDOR_ID, \
^
./arch/riscv/include/asm/alternative-macros.h:187:2: note: expanded from macro 'ALTERNATIVE'
_ALTERNATIVE_CFG(old_content, new_content, vendor_id, errata_id, CONFIG_k)
^
./arch/riscv/include/asm/alternative-macros.h:113:2: note: expanded from macro '_ALTERNATIVE_CFG'
__ALTERNATIVE_CFG(old_c, new_c, vendor_id, errata_id, IS_ENABLED(CONFIG_k))
^
./arch/riscv/include/asm/alternative-macros.h:110:2: note: expanded from macro '__ALTERNATIVE_CFG'
ALT_NEW_CONTENT(vendor_id, errata_id, enable, new_c)
^
./arch/riscv/include/asm/alternative-macros.h:99:3: note: expanded from macro 'ALT_NEW_CONTENT'
".org . - (889b - 888b) + (887b - 886b)\n" \
^
<inline asm>:26:6: note: instantiated into assembly here
.org . - (889b - 888b) + (887b - 886b)
^
This error happens because LLVM's integrated assembler has a one-pass
design, which means it cannot figure out the instruction lengths when
the .org directive is outside of the subsection that contains the
instructions, which was changed by the .option directives added by the
above change.
Move the .org directives before the .previous directive so that these
directives are always within the same subsection, which resolves the
failures and does not introduce any new issues with GNU as. This was
done for arm64 in commit 966a0acce2fc ("arm64/alternatives: move length
validation inside the subsection") and commit 22315a2296f4 ("arm64:
alternatives: Move length validation in alternative_{insn, endif}").
While there is no error from the assembly versions of the macro, they
appear to have the same problem so just make the same change there as
well so that there are no problems in the future.
Move the __ARCH_WANT_MEMFD_SECRET define added in commit 7bb7f2ac24a0
("arch, mm: wire up memfd_secret system call where relevant") to
<uapi/asm/unistd.h> so __NR_memfd_secret is defined when including
<unistd.h> in userspace.
This allows the memfd_secret selftest to pass on riscv.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Link: https://lore.kernel.org/r/20220505081815.22808-1-tklauser@distanz.ch Fixes: 7bb7f2ac24a0 ("arch, mm: wire up memfd_secret system call where relevant") Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
irq_work is triggered via an IPI, but the IPI infrastructure is not
included in uniprocessor kernels. As a result, irq_work never runs.
Fall back to the tick-based irq_work implementation on uniprocessor
configurations.
Fixes: 298447928bb1 ("riscv: Support irq_work via self IPIs") Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Link: https://lore.kernel.org/r/20220430030025.58405-1-samuel@sholland.org Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Because of the stack canary feature that reads from the current task
structure the stack canary value, the thread pointer register "tp" must
be set before calling any C function from head.S: by chance, setup_vm
and all the functions that it calls does not seem to be part of the
functions where the canary check is done, but in the following commits,
some functions will.
Commit 00ab027a3b82 ("RISC-V: Add kernel image sections to the resource tree")
marked IORESOURCE_BUSY for reserved memory, which caused resource map
failed in subsequent operations of related driver, so remove the
IORESOURCE_BUSY flag. In order to prohibit userland mapping reserved
memory, mark IORESOURCE_EXCLUSIVE for it.
The code to reproduce the issue,
dts:
mem0: memory@a0000000 {
reg = <0x0 0xa0000000 0 0x1000000>;
no-map;
};
&test {
status = "okay";
memory-region = <&mem0>;
};
code:
np = of_parse_phandle(pdev->dev.of_node, "memory-region", 0);
ret = of_address_to_resource(np, 0, &r);
base = devm_ioremap_resource(&pdev->dev, &r);
// base = -EBUSY
Implement fb_is_primary_device() function, so that fbcon detects if this
framebuffer belongs to the default graphics card which was used to start
the system.
Signed-off-by: Helge Deller <deller@gmx.de> Cc: stable@vger.kernel.org # v5.10+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It places the .got.plt input section before the .got input section.
The same is true for the default linker script (ld --verbose) on most
architectures except x86/x86-64.
The binfmt_flat loader should relocate all GOT entries until it encounters
a -1 (the LONG(-1) in the linker script).
The problem is that the .got.plt input section starts with a GOTPLT header
(which has size 16 bytes on elf64-riscv and 8 bytes on elf32-riscv), where
the first word is set to -1. See the binutils implementation for riscv [1].
This causes the binfmt_flat loader to stop relocating GOT entries
prematurely and thus causes the application to crash when running.
Fix this by skipping the whole GOTPLT header, since the whole GOTPLT header
is reserved for the dynamic linker.
The GOTPLT header will only be skipped for bFLT binaries with flag
FLAT_FLAG_GOTPIC set. This flag is unconditionally set by elf2flt if the
supplied ELF binary has the symbol _GLOBAL_OFFSET_TABLE_ defined.
ELF binaries without a .got input section should thus remain unaffected.
Tested on RISC-V Canaan Kendryte K210 and RISC-V QEMU nommu_virt_defconfig.
Maris found out that the quirk for TEAC devices to work around the
clock setup is needed to apply only when the base clock is changed,
e.g. from 48000-based clocks (48000, 96000, 192000, 384000) to
44100-based clocks (44100, 88200, 176400, 352800), or vice versa,
while switching to another clock with the same base clock doesn't need
the (forcible) interface setup.
This patch implements the optimization for the TEAC clock quirk to
avoid the unnecessary interface re-setup.
Fixes: 5ce0b06ae5e6 ("ALSA: usb-audio: Workaround for clock setup on TEAC devices") Reported-by: Maris Abele <maris7abele@gmail.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20220531130749.30357-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The commit being fixed was aiming to disallow users from incorrectly
obtaining writable pointer to memory that is only meant to be read. This
is enforced now using a MEM_RDONLY flag.
For instance, in case of global percpu variables, when the BTF type is
not struct (e.g. bpf_prog_active), the verifier marks register type as
PTR_TO_MEM | MEM_RDONLY from bpf_this_cpu_ptr or bpf_per_cpu_ptr
helpers. However, when passing such pointer to kfunc, global funcs, or
BPF helpers, in check_helper_mem_access, there is no expectation
MEM_RDONLY flag will be set, hence it is checked as pointer to writable
memory. Later, verifier sets up argument type of global func as
PTR_TO_MEM | PTR_MAYBE_NULL, so user can use a global func to get around
the limitations imposed by this flag.
This check will also cover global non-percpu variables that may be
introduced in kernel BTF in future.
Also, we update the log message for PTR_TO_BUF case to be similar to
PTR_TO_MEM case, so that the reason for error is clear to user.
Fixes: 34d3a78c681e ("bpf: Make per_cpu_ptr return rdonly PTR_TO_MEM.") Reviewed-by: Hao Luo <haoluo@google.com> Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com> Link: https://lore.kernel.org/r/20220319080827.73251-3-memxor@gmail.com Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It is not permitted to write to PTR_TO_MAP_KEY, but the current code in
check_helper_mem_access would allow for it, reject this case as well, as
helpers taking ARG_PTR_TO_UNINIT_MEM also take PTR_TO_MAP_KEY.
The 'n_buckets * (value_size + sizeof(struct stack_map_bucket))' part of the
allocated memory for 'smap' is never used after the memlock accounting was
removed, thus get rid of it.
[ Note, Daniel:
Commit b936ca643ade ("bpf: rework memlock-based memory accounting for maps")
moved `cost += n_buckets * (value_size + sizeof(struct stack_map_bucket))`
up and therefore before the bpf_map_area_alloc() allocation, sigh. In a later
step commit c85d69135a91 ("bpf: move memory size checks to bpf_map_charge_init()"),
and the overflow checks of `cost >= U32_MAX - PAGE_SIZE` moved into
bpf_map_charge_init(). And then 370868107bf6 ("bpf: Eliminate rlimit-based
memory accounting for stackmap maps") finally removed the bpf_map_charge_init().
Anyway, the original code did the allocation same way as /after/ this fix. ]
Fixes: b936ca643ade ("bpf: rework memlock-based memory accounting for maps") Signed-off-by: Yuntao Wang <ytcoode@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20220407130423.798386-1-ytcoode@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The data length of skb frags + frag_list may be greater than 0xffff, and
skb_header_pointer can not handle negative offset. So, here INT_MAX is used
to check the validity of offset. Add the same change to the related function
skb_store_bytes.
Fixes: 05c74e5e53f6 ("bpf: add bpf_skb_load_bytes helper") Signed-off-by: Liu Jian <liujian56@huawei.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Song Liu <songliubraving@fb.com> Link: https://lore.kernel.org/bpf/20220416105801.88708-2-liujian56@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The cnt value in the 'cnt >= BPF_MAX_TRAMP_PROGS' check does not
include BPF_TRAMP_MODIFY_RETURN bpf programs, so the number of
the attached BPF_TRAMP_MODIFY_RETURN bpf programs in a trampoline
can exceed BPF_MAX_TRAMP_PROGS.
When this happens, the assignment '*progs++ = aux->prog' in
bpf_trampoline_get_progs() will cause progs array overflow as the
progs field in the bpf_tramp_progs struct can only hold at most
BPF_MAX_TRAMP_PROGS bpf programs.
Fixes: 88fd9e5352fe ("bpf: Refactor trampoline update code") Signed-off-by: Yuntao Wang <ytcoode@gmail.com> Link: https://lore.kernel.org/r/20220430130803.210624-1-ytcoode@gmail.com Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
nfsd4_release_lockowner() holds clp->cl_lock when it calls
check_for_locks(). However, check_for_locks() calls nfsd_file_get()
/ nfsd_file_put() to access the backing inode's flc_posix list, and
nfsd_file_put() can sleep if the inode was recently removed.
Let's instead rely on the stateowner's reference count to gate
whether the release is permitted. This should be a reliable
indication of locks-in-use since file lock operations and
->lm_get_owner take appropriate references, which are released
appropriately when file locks are removed.
Reported-by: Dai Ngo <dai.ngo@oracle.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We need to filter out ENOMEM in nfs_error_is_fatal_on_server(), because
running out of memory on our client is not a server error.
Reported-by: Olga Kornievskaia <aglo@umich.edu> Fixes: 2dc23afffbca ("NFS: ENOMEM should also be a fatal error.") Cc: stable@vger.kernel.org Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The reference to `explicit_in_reply_to` is pointless as when the
reference was added in the form of "#15" [1], Section 15) was "The
canonical patch format".
The reference of "#15" had not been properly updated in a couple of
reorganizations during the plain-text SubmittingPatches era.
Fix it by using `the_canonical_patch_format`.
[1]: 2ae19acaa50a ("Documentation: Add "how to write a good patch summary" to SubmittingPatches")
Signed-off-by: Akira Yokosawa <akiyks@gmail.com> Fixes: 5903019b2a5e ("Documentation/SubmittingPatches: convert it to ReST markup") Fixes: 9b2c76777acc ("Documentation/SubmittingPatches: enrich the Sphinx output") Cc: Jonathan Corbet <corbet@lwn.net> Cc: Mauro Carvalho Chehab <mchehab@kernel.org> Cc: stable@vger.kernel.org # v4.9+ Link: https://lore.kernel.org/r/64e105a5-50be-23f2-6cae-903a2ea98e18@gmail.com Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>