There are two issues with "i2c: cadence: Fix the hold bit setting" commit.
1. In case of combined message request from user space, when the HOLD
bit is cleared in cdns_i2c_mrecv function, a STOP condition is sent
on the bus even before the last message is started. This is because when
the HOLD bit is cleared, the FIFOS are empty and there is no pending
transfer. The STOP condition should occur only after the last message
is completed.
2. The code added by the commit is redundant. Driver is handling the
setting/clearing of HOLD bit in right way before the commit.
The setting of HOLD bit based on 'bus_hold_flag' is taken care in
cdns_i2c_master_xfer function even before cdns_i2c_msend/cdns_i2c_recv
functions.
The clearing of HOLD bit is taken care at the end of cdns_i2c_msend and
cdns_i2c_recv functions based on bus_hold_flag and byte count.
Since clearing of HOLD bit is done after the slave address is written to
the register (writing to address register triggers the message transfer),
it is ensured that STOP condition occurs at the right time after
completion of the pending transfer (last message).
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
According to the report of [1], this driver is possible to cause
the following error in ravb_tx_timeout_work().
ravb e6800000.ethernet ethernet: failed to switch device to config mode
This error means that the hardware could not change the state
from "Operation" to "Configuration" while some tx and/or rx queue
are operating. After that, ravb_config() in ravb_dmac_init() will fail,
and then any descriptors will be not allocaled anymore so that NULL
pointer dereference happens after that on ravb_start_xmit().
To fix the issue, the ravb_tx_timeout_work() should check
the return values of ravb_stop_dma() and ravb_dmac_init().
If ravb_stop_dma() fails, ravb_tx_timeout_work() re-enables TX and RX
and just exits. If ravb_dmac_init() fails, just exits.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The kernel test bot reported[1] that using set_mask_bits on a u8 causes
the following issue on parisc:
hppa-linux-ld: drivers/phy/ti/phy-tusb1210.o: in function `tusb1210_probe':
>> (.text+0x2f4): undefined reference to `__cmpxchg_called_with_bad_pointer'
>> hppa-linux-ld: (.text+0x324): undefined reference to `__cmpxchg_called_with_bad_pointer'
hppa-linux-ld: (.text+0x354): undefined reference to `__cmpxchg_called_with_bad_pointer'
I/O requests may be held in scheduler queue because of resource contention.
The starvation scenario was handled properly in the regular completion
path but we failed to account for it during I/O submission. This lead to
the hang captured below. Make sure we run the queue when resource
contention is encountered in the submission path.
Link: https://lore.kernel.org/r/20200720025435.812030-1-ming.lei@redhat.com Cc: linux-block@vger.kernel.org Cc: Christoph Hellwig <hch@lst.de> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The implementation of s3fwrn5_recv_frame() is supposed to consume skb on
all execution paths. Release skb before returning -ENODEV.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
$ sudo ./ip_defrag.sh
+ set -e
+ mktemp -u XXXXXX
+ readonly NETNS=ns-rGlXcw
+ trap cleanup EXIT
+ setup
+ ip netns add ns-rGlXcw
+ ip -netns ns-rGlXcw link set lo up
+ ip netns exec ns-rGlXcw sysctl -w net.ipv4.ipfrag_high_thresh=9000000
+ ip netns exec ns-rGlXcw sysctl -w net.ipv4.ipfrag_low_thresh=7000000
+ ip netns exec ns-rGlXcw sysctl -w net.ipv4.ipfrag_time=1
+ ip netns exec ns-rGlXcw sysctl -w net.ipv6.ip6frag_high_thresh=9000000
+ ip netns exec ns-rGlXcw sysctl -w net.ipv6.ip6frag_low_thresh=7000000
+ ip netns exec ns-rGlXcw sysctl -w net.ipv6.ip6frag_time=1
+ ip netns exec ns-rGlXcw sysctl -w net.netfilter.nf_conntrack_frag6_high_thresh=9000000
+ cleanup
+ ip netns del ns-rGlXcw
$ ls -la /proc/sys/net/netfilter/nf_conntrack_frag6_high_thresh
ls: cannot access '/proc/sys/net/netfilter/nf_conntrack_frag6_high_thresh': No such file or directory
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
This is likely firmware causing this but its starting to annoy customers.
Change the message level to verbose to prevent the spam.
Note that this seems to only show up with ISCSI enabled on the HBA via the
qedi driver.
Signed-off-by: Laurence Oberman <loberman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
During setup():
...
for ns in h0 r1 h1 h2 h3
do
create_ns ${ns}
done
...
while in cleanup():
...
for n in h1 r1 h2 h3 h4
do
ip netns del ${n} 2>/dev/null
done
...
and after removing the stderr redirection in cleanup():
$ sudo ./fib_nexthop_multiprefix.sh
...
TEST: IPv4: host 0 to host 3, mtu 1400 [ OK ]
TEST: IPv6: host 0 to host 3, mtu 1400 [ OK ]
Cannot remove namespace file "/run/netns/h4": No such file or directory
$ echo $?
1
and a non-zero return code, make kselftests fail (even if the test
itself is fine):
...
not ok 34 selftests: net: fib_nexthop_multiprefix.sh # exit=1
...
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
On sparc32, tcflag_t is "unsigned long", unlike on all other
architectures, where it is "unsigned int":
drivers/net/usb/hso.c: In function ‘hso_serial_set_termios’:
include/linux/kern_levels.h:5:18: warning: format ‘%d’ expects argument of type ‘unsigned int’, but argument 4 has type ‘tcflag_t {aka long unsigned int}’ [-Wformat=]
drivers/net/usb/hso.c:1393:3: note: in expansion of macro ‘hso_dbg’
hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n",
^~~~~~~
include/linux/kern_levels.h:5:18: warning: format ‘%d’ expects argument of type ‘unsigned int’, but argument 5 has type ‘tcflag_t {aka long unsigned int}’ [-Wformat=]
drivers/net/usb/hso.c:1393:3: note: in expansion of macro ‘hso_dbg’
hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n",
^~~~~~~
As "unsigned long" is 32-bit on sparc32, fix this by casting all tcflag_t
parameters to "unsigned int".
While at it, use "%u" to format unsigned numbers.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When vxlan interface is deleted, all fdbs are deleted by vxlan_flush().
vxlan_flush() flushes fdbs but it doesn't delete fdb, which contains
all-zeros-mac because it is deleted by vxlan_uninit().
But vxlan_uninit() deletes only the fdb, which contains both all-zeros-mac
and default vni.
So, the fdb, which contains both all-zeros-mac and non-default vni
will not be deleted.
Test commands:
ip link add vxlan0 type vxlan dstport 4789 external
ip link set vxlan0 up
bridge fdb add to 00:00:00:00:00:00 dst 172.0.0.1 dev vxlan0 via lo \
src_vni 10000 self permanent
ip link del vxlan0
Fixes: 3ad7a4b141eb ("vxlan: support fdb and learning in COLLECT_METADATA mode") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When recording with cache-misses and arm_spe_x event, I found that it
will just fail without showing any error info if i put cache-misses
after 'arm_spe_x' event.
[root@localhost 0620]# perf record -e cache-misses \
-e arm_spe_0/ts_enable=1,pct_enable=1,pa_enable=1,load_filter=1,jitter=1,store_filter=1,min_latency=0/ sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.067 MB perf.data ]
[root@localhost 0620]#
[root@localhost 0620]# perf record -e arm_spe_0/ts_enable=1,pct_enable=1,pa_enable=1,load_filter=1,jitter=1,store_filter=1,min_latency=0/ \
-e cache-misses sleep 1
[root@localhost 0620]#
The current code can only work if the only event to be traced is an
'arm_spe_x', or if it is the last event to be specified. Otherwise the
last event type will be checked against all the arm_spe_pmus[i]->types,
none will match and an out of bound 'i' index will be used in
arm_spe_recording_init().
We don't support concurrent multiple arm_spe_x events currently, that
is checked in arm_spe_recording_options(), and it will show the relevant
info. So add the check and record of the first found 'arm_spe_pmu' to
fix this issue here.
Fixes: ffd3d18c20b8 ("perf tools: Add ARM Statistical Profiling Extensions (SPE) support") Signed-off-by: Wei Li <liwei391@huawei.com> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Tested-by-by: Leo Yan <leo.yan@linaro.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Hanjun Guo <guohanjun@huawei.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kim Phillips <kim.phillips@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mike Leach <mike.leach@linaro.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Suzuki Poulouse <suzuki.poulose@arm.com> Cc: linux-arm-kernel@lists.infradead.org Link: http://lore.kernel.org/lkml/20200724071111.35593-2-liwei391@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The function invokes bpf_prog_inc(), which increases the reference
count of a bpf_prog object "rq->xdp_prog" if the object isn't NULL.
The refcount leak issues take place in two error handling paths. When
either mlx5_wq_ll_create() or mlx5_wq_cyc_create() fails, the function
simply returns the error code and forgets to drop the reference count
increased earlier, causing a reference count leak of "rq->xdp_prog".
Fix this issue by jumping to the error handling path err_rq_wq_destroy
while either function fails.
Fixes: 422d4c401edd ("net/mlx5e: RX, Split WQ objects for different RQ types") Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn> Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Fix the missing clk_disable_unprepare() before return
from gemini_ethernet_port_probe() in the error handling case.
Fixes: 4d5ae32f5e1e ("net: ethernet: Add a driver for Gemini gigabit ethernet") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If some processes in nixge_probe() fail, free_netdev(dev)
needs to be called to aviod a memory leak.
Fixes: 87ab207981ec ("net: nixge: Separate ctrl and dma resources") Fixes: abcd3d6fc640 ("net: nixge: Fix error path for obtaining mac address") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Lu Wei <luwei32@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Fix kernel oops observed when an ext adv data is larger than 31 bytes.
This can be reproduced by setting up an advertiser with advertisement
larger than 31 bytes. The issue is not sensitive to the advertisement
content. In particular, this was reproduced with an advertisement of
229 bytes filled with 'A'. See stack trace below.
This is fixed by not catching ext_adv as legacy adv are only cached to
be able to concatenate a scanable adv with its scan response before
sending it up through mgmt.
Although iph is expected to point to at least 20 bytes of valid memory,
ihl may be bogus, for example on reception of a corrupt packet. If it
happens to be less than 5, we really don't want to run away and
dereference 16GB worth of memory until it wraps back to exactly zero...
Fixes: 0e455d8e80aa ("arm64: Implement optimised IP checksum helpers") Reported-by: guodeqing <geffrey.guo@huawei.com> Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Commit f7b93d42945c ("arm64/alternatives: use subsections for replacement
sequences") breaks LLVM's integrated assembler, because due to its
one-pass design, it cannot compute instruction sequence lengths before the
layout for the subsection has been finalized. This change fixes the build
by moving the .org directives inside the subsection, so they are processed
after the subsection layout is known.
Fixes: f7b93d42945c ("arm64/alternatives: use subsections for replacement sequences") Signed-off-by: Sami Tolvanen <samitolvanen@google.com> Link: https://github.com/ClangBuiltLinux/linux/issues/1078 Link: https://lore.kernel.org/r/20200730153701.3892953-1-samitolvanen@google.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
A mpath object can hold reference on a list of skb that are waiting for
mpath resolution to be sent. When destroying a mpath this skb list
should be cleaned up in order to not leak memory.
Fix HASH_OF_MAPS bug of not putting inner map pointer on bpf_map_elem_update()
operation. This is due to per-cpu extra_elems optimization, which bypassed
free_htab_elem() logic doing proper clean ups. Make sure that inner map is put
properly in optimized case as well.
Fixes: 8c290e60fa2a ("bpf: fix hashmap extra_elems logic") Signed-off-by: Andrii Nakryiko <andriin@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Song Liu <songliubraving@fb.com> Link: https://lore.kernel.org/bpf/20200729040913.2815687-1-andriin@fb.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
RX queue IRQ mappings are disposed in both the TX IRQ and RX IRQ
error paths. Fix this and dispose of TX IRQ mappings correctly in
case of an error.
Fixes: ea22d51a7831 ("ibmvnic: simplify and improve driver probe function") Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The lifetime of EMAD transactions (i.e., 'struct mlxsw_reg_trans') is
managed using RCU. They are freed using kfree_rcu() once the transaction
ends.
However, in case the transaction failed it is freed immediately after being
removed from the active transactions list. This is problematic because it is
still possible for a different CPU to dereference the transaction from an RCU
read-side critical section while traversing the active transaction list in
mlxsw_emad_rx_listener_func(). In which case, a use-after-free is triggered
[1].
Fix this by freeing the transaction after a grace period by calling
kfree_rcu().
[1]
BUG: KASAN: use-after-free in mlxsw_emad_rx_listener_func+0x969/0xac0 drivers/net/ethernet/mellanox/mlxsw/core.c:671
Read of size 8 at addr ffff88800b7964e8 by task syz-executor.2/2881
Memory state around the buggy address: ffff88800b796380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88800b796400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff88800b796480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff88800b796500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88800b796580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: caf7297e7ab5 ("mlxsw: core: Introduce support for asynchronous EMAD register access") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The lifetime of the Rx listener item ('rxl_item') is managed using RCU,
but is dereferenced outside of RCU read-side critical section, which can
lead to a use-after-free.
Fix this by increasing the scope of the RCU read-side critical section.
Fixes: 93c1edb27f9e ("mlxsw: Introduce Mellanox switch driver core") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
This is a very similar problem to what had been fixed in:
commit 0d98ba8d70b0 ("scsi: hpsa: disable device during shutdown")
to address https://bugzilla.kernel.org/show_bug.cgi?id=199779.
Fixes: 2ba5fbd62b25 ("net/mlx4_core: Handle AER flow properly") Reported-by: Jake Lawrence <lawja@fb.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The rcu_dereference call in rht_ptr_rcu is completely bogus because
we've already dereferenced the value in __rht_ptr and operated on it.
This causes potential double readings which could be fatal. The RCU
dereference must occur prior to the comparison in __rht_ptr.
This patch changes the order of RCU dereference so that it is done
first and the result is then fed to __rht_ptr. The RCU marking
changes have been minimised using casts which will be removed in
a follow-up patch.
Fixes: ba6306e3f648 ("rhashtable: Remove RCU marking from...") Reported-by: "Gong, Sishuai" <sishuai@purdue.edu> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The interrupt URB transfer-buffer was never freed on disconnect or after
probe errors.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Add the missing endpoint sanity check to prevent a NULL-pointer
dereference should a malicious device lack the expected endpoints.
Note that the driver has a broken endpoint-lookup helper,
lan78xx_get_endpoints(), which can end up accepting interfaces in an
altsetting without endpoints as long as *some* altsetting has a bulk-in
and a bulk-out endpoint.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
After the cited commit, function 'mlx5_eswitch_set_vport_vlan' started
to acquire esw->state_lock.
However, esw is not defined for VF devices, hence attempting to set vf
VLANID on a VF dev will cause a kernel panic.
Fix it by moving up the (redundant) esw validation from function
'__mlx5_eswitch_set_vport_vlan' since the rest of the callers now have
and use a valid esw.
For example with vf device eth4:
# ip link set dev eth4 vf 0 vlan 0
When setting the PF interface up/down, notify the firmware to update
uplink state via MODIFY_VPORT_STATE, when E-Switch is enabled.
This behavior will prevent sending traffic out on uplink port when PF is
down, such as sending traffic from a VF interface which is still up.
Currently when calling mlx5e_open/close(), the driver only sends PAOS
command to notify the firmware to set the physical port state to
up/down, however, it is not sufficient. When VF is in "auto" state, it
follows the uplink state, which was not updated on mlx5e_open/close()
before this patch.
When switchdev mode is enabled and uplink representor is first enabled,
set the uplink port state value back to its FW default "AUTO".
Fixes: 63bfd399de55 ("net/mlx5e: Send PAOS command on interface up/down") Signed-off-by: Ron Diskin <rondi@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
On failure to attach the netdev, fix the rollback by re-setting the
device's state back to MLX5E_STATE_DESTROYING.
Failing to attach doesn't stop statistics polling via .ndo_get_stats64.
In this case, although the device is not attached, it falsely continues
to query the firmware for counters. Setting the device's state back to
MLX5E_STATE_DESTROYING prevents the firmware counters query.
Fixes: 26e59d8077a3 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks") Signed-off-by: Aya Levin <ayal@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When user had created a FD rule, all the aRFS rules should be clear up.
HNS3 process flow as below:
1.get spin lock of fd_ruls_list
2.clear up all aRFS rules
3.release lock
4.get spin lock of fd_ruls_list
5.creat a rules
6.release lock;
There is a short period of time between step 3 and step 4, which would
creatting some new aRFS FD rules if driver was receiving packet.
So refactor the fd_rule_lock to fix it.
Fixes: 441228875706 ("net: hns3: refine the flow director handle") Signed-off-by: Guojia Liao <liaoguojia@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When the queue depth and queue parameters are modified, there is
a low probability that TX timeout occurs. The two operations cause
the link to be down or up when the watchdog is still working. All
queues are stopped when the link is down. After the carrier is on,
all queues are woken up. If the watchdog detects the link between
the carrier on and wakeup queues, a false TX timeout occurs.
So fix this issue by modifying the sequence of carrier on and queue
wakeup, which is symmetrical to the link down action.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The slow path for traced system call entries accessed a wrong memory
location to get the number of the maximum allowed system call number.
Renumber the numbered "local" label for the correct location to avoid
collisions with actual local labels.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de> Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Fixes: f3a8308864f920d2 ("sh: Add a few missing irqflags tracing markers.") Signed-off-by: Rich Felker <dalias@libc.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
On powerpcle, int64_t maps to long long. Clang 9 threw:
warning: absolute value function 'labs' given an argument of type \
'long long' but has parameter of type 'long' which may cause \
truncation of value [-Wabsolute-value]
if (labs(tstop - texpect) > cfg_variance_us)
Tested: make -C tools/testing/selftests TARGETS="net" run_tests
Fixes: af5136f95045 ("selftests/net: SO_TXTIME with ETF and FQ") Signed-off-by: Tanner Love <tannerlove@google.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Clang 9 threw:
warning: format specifies type 'unsigned short' but the argument has \
type 'int' [-Wformat]
typeflags, PORT_BASE, PORT_BASE + port_off);
Tested: make -C tools/testing/selftests TARGETS="net" run_tests
Fixes: 77f65ebdca50 ("packet: packet fanout rollover during socket overload") Signed-off-by: Tanner Love <tannerlove@google.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The signedness of char is implementation-dependent. Some systems
(including PowerPC and ARM) use unsigned char. Clang 9 threw:
warning: result of comparison of constant -1 with expression of type \
'char' is always true [-Wtautological-constant-out-of-range-compare]
&arg_index)) != -1) {
Tested: make -C tools/testing/selftests TARGETS="net" run_tests
Fixes: 16e781224198 ("selftests/net: Add a test to validate behavior of rx timestamps") Signed-off-by: Tanner Love <tannerlove@google.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The commits "xfrm: Move dst->path into struct xfrm_dst"
and "net: Create and use new helper xfrm_dst_child()."
changed xfrm bundle handling under the assumption
that xdst->path and dst->child are not a NULL pointer
only if dst->xfrm is not a NULL pointer. That is true
with one exception. If the xfrm hold queue is used
to wait until a SA is installed by the key manager,
we create a dummy bundle without a valid dst->xfrm
pointer. The current xfrm bundle handling crashes
in that case. Fix this by extending the NULL check
of dst->xfrm with a test of the DST_XFRM_QUEUE flag.
Fixes: 0f6c480f23f4 ("xfrm: Move dst->path into struct xfrm_dst") Fixes: b92cf4aab8e6 ("net: Create and use new helper xfrm_dst_child().") Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The hardware codec on the A10, A10s, A13 and A20 needs buffer in the
first 256MB of RAM. This was solved by setting the CMA pool at a fixed
address in that range.
However, in recent kernels there's something else that comes in and
reserve some range that end up conflicting with our default pool
requirement, and thus makes its reservation fail.
The video codec will then use buffers from the usual default pool,
outside of the range it can access, and will fail to decode anything.
Since we're only concerned about that 256MB, we can however relax the
allocation to just specify the range that's allowed, and not try to
enforce a specific address.
Fixes: 5949bc5602cc ("ARM: dts: sun4i-a10: Add Video Engine and reserved memory nodes") Fixes: 960432010156 ("ARM: dts: sun5i: Add Video Engine and reserved memory nodes") Fixes: c2a641a74850 ("ARM: dts: sun7i-a20: Add Video Engine and reserved memory nodes") Signed-off-by: Maxime Ripard <maxime@cerno.tech> Acked-by: Chen-Yu Tsai <wens@csie.org> Link: https://lore.kernel.org/r/20200704130829.34297-1-maxime@cerno.tech Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
x25_connect() invokes x25_get_neigh(), which returns a reference of the
specified x25_neigh object to "x25->neighbour" with increased refcnt.
When x25 connect success and returns, the reference still be hold by
"x25->neighbour", so the refcount should be decreased in
x25_disconnect() to keep refcount balanced.
The reference counting issue happens in x25_disconnect(), which forgets
to decrease the refcnt increased by x25_get_neigh() in x25_connect(),
causing a refcnt leak.
Fix this issue by calling x25_neigh_put() before x25_disconnect()
returns.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
In binutils 2.35, 'nm -D' changed to show symbol versions along with
symbol names, with the usual @@ separator. When generating
libtraceevent-dynamic-list we need just the names, so strip off the
version suffix if present.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Tested-by: Salvatore Bonaccorso <carnil@debian.org> Reviewed-by: Steven Rostedt <rostedt@goodmis.org> Cc: linux-trace-devel@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
rds_notify_queue_get() is potentially copying uninitialized kernel stack
memory to userspace since the compiler may leave a 4-byte hole at the end
of `cmsg`.
In 2016 we tried to fix this issue by doing `= { 0 };` on `cmsg`, which
unfortunately does not always initialize that 4-byte hole. Fix it by using
memset() instead.
Cc: stable@vger.kernel.org Fixes: f037590fff30 ("rds: fix a leak of kernel memory") Fixes: bdbe6fbc6a2f ("RDS: recv.c") Suggested-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
A use-after-free in drm_gem_open_ioctl can happen if the
GEM object handle is closed between the idr lookup and
retrieving the size from said object since a local reference
is not being held at that point. Hold the local reference
while the object can still be accessed to fix this and
plug the potential security hole.
Signed-off-by: Steve Cohen <cohens@codeaurora.org> Cc: stable@vger.kernel.org Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/1595284250-31580-1-git-send-email-cohens@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The function mipi_dbi_spi1_transfer() will transfer its payload as 9-bit
data, the 9th (MSB) bit being the data/command bit. In order to do that,
it unpacks the 8-bit values into 16-bit values, then sets the 9th bit if
the byte corresponds to data, clears it otherwise. The 7 MSB are
padding. The array of now 16-bit values is then passed to the SPI core
for transfer.
This function was broken since its introduction, as the length of the
SPI transfer was set to the payload size before its conversion, but the
payload doubled in size due to the 8-bit -> 16-bit conversion.
Fixes: 02dd95fe3169 ("drm/tinydrm: Add MIPI DBI support") Cc: <stable@vger.kernel.org> # 5.4+ Signed-off-by: Paul Cercueil <paul@crapouillou.net> Reviewed-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Noralf Trønnes <noralf@tronnes.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200703141341.1266263-1-paul@crapouillou.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Compiler leaves a 4-byte hole near the end of `dev_info`, causing
amdgpu_info_ioctl() to copy uninitialized kernel stack memory to userspace
when `size` is greater than 356.
In 2015 we tried to fix this issue by doing `= {};` on `dev_info`, which
unfortunately does not initialize that 4-byte hole. Fix it by using
memset() instead.
Cc: stable@vger.kernel.org Fixes: c193fa91b918 ("drm/amdgpu: information leak in amdgpu_info_ioctl()") Fixes: d38ceaf99ed0 ("drm/amdgpu: add core driver (v4)") Suggested-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
This patch fixes a race condition that causes a use-after-free during
amdgpu_dm_atomic_commit_tail. This can occur when 2 non-blocking commits
are requested and the second one finishes before the first. Essentially,
this bug occurs when the following sequence of events happens:
1. Non-blocking commit #1 is requested w/ a new dm_state #1 and is
deferred to the workqueue.
2. Non-blocking commit #2 is requested w/ a new dm_state #2 and is
deferred to the workqueue.
3. Commit #2 starts before commit #1, dm_state #1 is used in the
commit_tail and commit #2 completes, freeing dm_state #1.
4. Commit #1 starts after commit #2 completes, uses the freed dm_state
1 and dereferences a freelist pointer while setting the context.
Since this bug has only been spotted with fast commits, this patch fixes
the bug by clearing the dm_state instead of using the old dc_state for
fast updates. In addition, since dm_state is only used for its dc_state
and amdgpu_dm_atomic_commit_tail will retain the dc_state if none is found,
removing the dm_state should not have any consequences in fast updates.
This use-after-free bug has existed for a while now, but only caused a
noticeable issue starting from 5.7-rc1 due to 3202fa62f ("slub: relocate
freelist pointer to middle of object") moving the freelist pointer from
dm_state->base (which was unused) to dm_state->context (which is
dereferenced).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=207383 Fixes: bd200d190f45 ("drm/amd/display: Don't replace the dc_state for fast updates") Reported-by: Duncan <1i5t5.duncan@cox.net> Signed-off-by: Mazin Rezk <mnrzk@protonmail.com> Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
free cmd id is read using virtio endian, spec says all fields
in balloon are LE. Fix it up.
Fixes: 86a559787e6f ("virtio-balloon: VIRTIO_BALLOON_F_FREE_PAGE_HINT") Cc: stable@vger.kernel.org Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Wei Wang <wei.w.wang@intel.com> Acked-by: David Hildenbrand <david@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The current pin muxing scheme muxes GPIO_1 pad for USB_OTG_ID
because of which when card is inserted, usb otg is enumerated
and the card is never detected.
[ 64.492645] cfg80211: failed to load regulatory.db
[ 64.492657] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
[ 76.343711] ci_hdrc ci_hdrc.0: EHCI Host Controller
[ 76.349742] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 2
[ 76.388862] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[ 76.396650] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[ 76.405412] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 76.412763] usb usb2: Product: EHCI Host Controller
[ 76.417666] usb usb2: Manufacturer: Linux 5.8.0-rc1-next-20200618 ehci_hcd
[ 76.424623] usb usb2: SerialNumber: ci_hdrc.0
[ 76.431755] hub 2-0:1.0: USB hub found
[ 76.435862] hub 2-0:1.0: 1 port detected
The TRM mentions GPIO_1 pad should be muxed/assigned for card detect
and ENET_RX_ER pad for USB_OTG_ID for proper operation.
This patch fixes pin muxing as per TRM and is tested on a
i.Core 1.5 MX6 DL SOM.
[ 22.449165] mmc0: host does not support reading read-only switch, assuming write-enable
[ 22.459992] mmc0: new high speed SDHC card at address 0001
[ 22.469725] mmcblk0: mmc0:0001 EB1QT 29.8 GiB
[ 22.478856] mmcblk0: p1 p2
Unprivileged memory accesses generated by the so-called "translated"
instructions (e.g. LDRT) in kernel mode can cause user watchpoints to fire
unexpectedly. In such cases, the hw_breakpoint logic will invoke the user
overflow handler which will typically raise a SIGTRAP back to the current
task. This is futile when returning back to the kernel because (a) the
signal won't have been delivered and (b) userspace can't handle the thing
anyway.
Avoid invoking the user overflow handler for watchpoints triggered by
kernel uaccess routines, and instead single-step over the faulting
instruction as we would if no overflow handler had been installed.
Cc: <stable@vger.kernel.org> Fixes: f81ef4a920c8 ("ARM: 6356/1: hw-breakpoint: add ARM backend for the hw-breakpoint framework") Reported-by: Luis Machado <luis.machado@linaro.org> Tested-by: Luis Machado <luis.machado@linaro.org> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Use offsetof to calculate offset of a field to take advantage of
compiler built-in version when possible, and avoid UBSAN warning when
compiling with Clang:
==================================================================
UBSAN: Undefined behaviour in net/wireless/wext-core.c:525:14
member access within null pointer of type 'struct iw_point'
CPU: 3 PID: 165 Comm: kworker/u16:3 Tainted: G S W 4.19.23 #43
Workqueue: cfg80211 __cfg80211_scan_done [cfg80211]
Call trace:
dump_backtrace+0x0/0x194
show_stack+0x20/0x2c
__dump_stack+0x20/0x28
dump_stack+0x70/0x94
ubsan_epilogue+0x14/0x44
ubsan_type_mismatch_common+0xf4/0xfc
__ubsan_handle_type_mismatch_v1+0x34/0x54
wireless_send_event+0x3cc/0x470
___cfg80211_scan_done+0x13c/0x220 [cfg80211]
__cfg80211_scan_done+0x28/0x34 [cfg80211]
process_one_work+0x170/0x35c
worker_thread+0x254/0x380
kthread+0x13c/0x158
ret_from_fork+0x10/0x18
===================================================================
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/r/20191204081307.138765-1-pihsun@chromium.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
vhost/scsi doesn't handle type conversion correctly
for request type when using virtio 1.0 and up for BE,
or cross-endian platforms.
Fix it up using vhost_32_to_cpu.
Cc: stable@vger.kernel.org Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The lookaside count is improperly initialized to the size of the
Receive Queue with the additional +1. In the traces below, the
RQ size is 384, so the count was set to 385.
The lookaside count is then rarely refreshed. Note the high and
incorrect count in the trace below:
Note that the RQ is empty (head == tail) yet we return the RWQE at tail 1,
which is not valid because of the bogus high count.
Best case, the RWQE has never been posted and the rc logic sees an RWQE
that is too small (all zeros) and puts the QP into an error state.
In the worst case, a server slow at posting receive buffers might fool
rvt_get_rwqe() into fetching an old RWQE and corrupt memory.
Fix by deleting the faulty initialization code and creating an
inline to fetch the posted count and convert all callers to use
new inline.
Fixes: f592ae3c999f ("IB/rdmavt: Fracture single lock used for posting and processing RWQEs") Link: https://lore.kernel.org/r/20200728183848.22226.29132.stgit@awfm-01.aw.intel.com Reported-by: Zhaojuan Guo <zguo@redhat.com> Cc: <stable@vger.kernel.org> # 5.4.x Reviewed-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Tested-by: Honggang Li <honli@redhat.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
It's been reported that, when neither nouveau nor Nvidia graphics
driver is used, the screen starts flickering. And, after comparing
between the working case (stable 4.4.x) and the broken case, it turned
out that the problem comes from the audio component binding. The
Nvidia and AMD audio binding code clears the bus->keep_power flag
whenever snd_hdac_acomp_init() succeeds. But this doesn't mean that
the component is actually bound, but it merely indicates that it's
ready for binding. So, when both nouveau and Nvidia are blacklisted
or not ready, the driver keeps running without the audio component but
also with bus->keep_power = false. This made the driver runtime PM
kicked in and powering down when unused, which results in flickering
in the graphics side, as it seems.
For fixing the bug, this patch moves the bus->keep_power flag change
into generic_acomp_notifier_set() that is the function called from the
master_bind callback of component ops; i.e. it's guaranteed that the
binding succeeded.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208609 Fixes: 5a858e79c911 ("ALSA: hda - Disable audio component for legacy Nvidia HDMI codecs") Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200728082033.23933-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
This patch fixes a small typo I accidently submitted with the initial patch. The board should be named GA401 not G401.
Fixes: ff53664daff2 ("ALSA: hda/realtek: enable headset mic of ASUS ROG Zephyrus G14(G401) series with ALC289") Signed-off-by: Armas Spann <zappel@retarded.farm> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200724140837.302763-1-zappel@retarded.farm Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
This patch adds support for headset mic to the ASUS ROG Zephyrus
G15(GA502) notebook series by adding the corresponding
vendor/pci_device id, as well as adding a new fixup for the used
realtek ALC289. The fixup stets the correct pin to get the headset mic
correctly recognized on audio-jack.
Signed-off-by: Armas Spann <zappel@retarded.farm> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200724140616.298892-1-zappel@retarded.farm Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When handling a page fault, we drop mmap_sem to start async readahead so
that we don't block on IO submission with mmap_sem held. However there's
no point to drop mmap_sem in case readahead is disabled. Handle that case
to avoid pointless dropping of mmap_sem and retrying the fault. This was
actually reported to block mlockall(MCL_CURRENT) indefinitely.
Fixes: 6b4c9f446981 ("filemap: drop the mmap_sem for all blocking operations") Reported-by: Minchan Kim <minchan@kernel.org> Reported-by: Robert Stupp <snazy@gmx.de> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: Minchan Kim <minchan@kernel.org> Link: http://lkml.kernel.org/r/20200212101356.30759-1-jack@suse.cz Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: SeongJae Park <sjpark@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Recently ASPM handling was changed to allow ASPM on PCIe-to-PCI/PCI-X
bridges. Unfortunately the ASMedia ASM1083/1085 PCIe to PCI bridge device
doesn't seem to function properly with ASPM enabled. On an Asus PRIME
H270-PRO motherboard, it causes errors like these:
In addition to flooding the kernel log, this also causes the machine to
wake up immediately after suspend is initiated.
The device advertises ASPM L0s and L1 support in the Link Capabilities
register, but the ASMedia web page for ASM1083 [1] claims "No PCIe ASPM
support".
Windows 10 (build 2004) enables L0s, but it also logs correctable PCIe
errors.
For all data packets transmitted, host gets htt tx completion event. Some QCA9984
firmware releases support WMI_SERVICE_TX_DATA_ACK_RSSI, which gives data
ack rssi values to host through htt event of data tx completion. Data ack rssi
values are valid if A0 bit is set in HTT rx message. So enable the feature also
for QCA9884.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00044
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org> Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
[kvalo@codeaurora.org: improve commit log] Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Release all allocated memory if sha type is invalid:
In ccp_run_sha_cmd, if the type of sha is invalid, the allocated
hmac_buf should be released.
v2: fix the goto.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Acked-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Or Cohen [Fri, 4 Sep 2020 04:05:28 +0000 (21:05 -0700)]
UBUNTU: SAUCE: net/packet: fix overflow in tpacket_rcv
Using tp_reserve to calculate netoff can overflow as
tp_reserve is unsigned int and netoff is unsigned short.
This may lead to macoff receving a smaller value then
sizeof(struct virtio_net_hdr), and if po->has_vnet_hdr
is set, an out-of-bounds write will occur when
calling virtio_net_hdr_from_skb.
The bug is fixed by converting netoff to unsigned int
and checking if it exceeds USHRT_MAX.
This addresses CVE-2020-14386
Fixes: 8913336a7e8d ("packet: add PACKET_RESERVE sockopt") Signed-off-by: Or Cohen <orcohen@paloaltonetworks.com> Signed-off-by: Eric Dumazet <edumazet@google.com>
CVE-2020-14386 Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com> Acked-by: Ian May <ian.may@canonical.com>
Michael Ellerman [Wed, 26 Aug 2020 01:31:00 +0000 (03:31 +0200)]
powerpc/64s: Don't init FSCR_DSCR in __init_FSCR()
BugLink: https://bugs.launchpad.net/bugs/1888332
__init_FSCR() was added originally in commit 2468dcf641e4 ("powerpc:
Add support for context switching the TAR register") (Feb 2013), and
only set FSCR_TAR.
At that point FSCR (Facility Status and Control Register) was not
context switched, so the setting was permanent after boot.
Later we added initialisation of FSCR_DSCR to __init_FSCR(), in commit 54c9b2253d34 ("powerpc: Set DSCR bit in FSCR setup") (Mar 2013), again
that was permanent after boot.
Then commit 2517617e0de6 ("powerpc: Fix context switch DSCR on
POWER8") (Aug 2013) added a limited context switch of FSCR, just the
FSCR_DSCR bit was context switched based on thread.dscr_inherit. That
commit said "This clears the H/FSCR DSCR bit initially", but it
didn't, it left the initialisation of FSCR_DSCR in __init_FSCR().
However the initial context switch from init_task to pid 1 would clear
FSCR_DSCR because thread.dscr_inherit was 0.
That commit also introduced the requirement that FSCR_DSCR be clear
for user processes, so that we can take the facility unavailable
interrupt in order to manage dscr_inherit.
Then in commit 152d523e6307 ("powerpc: Create context switch helpers
save_sprs() and restore_sprs()") (Dec 2015) FSCR was added to
thread_struct. However it still wasn't fully context switched, we just
took the existing value and set FSCR_DSCR if the new thread had
dscr_inherit set. FSCR was still initialised at boot to FSCR_DSCR |
FSCR_TAR, but that value was not propagated into the thread_struct, so
the initial context switch set FSCR_DSCR back to 0.
Finally commit b57bd2de8c6c ("powerpc: Improve FSCR init and context
switching") (Jun 2016) added a full context switch of the FSCR, and
added an initialisation of init_task.thread.fscr to FSCR_TAR |
FSCR_EBB, but omitted FSCR_DSCR.
The end result is that swapper runs with FSCR_DSCR set because of the
initialisation in __init_FSCR(), but no other processes do, they use
the value from init_task.thread.fscr.
Having FSCR_DSCR set for swapper allows it to access SPR 3 from
userspace, but swapper never runs userspace, so it has no useful
effect. It's also confusing to have the value initialised in two
places to two different values.
So remove FSCR_DSCR from __init_FSCR(), this at least gets us to the
point where there's a single value of FSCR, even if it's still set in
two places.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Tested-by: Alistair Popple <alistair@popple.id.au> Link: https://lore.kernel.org/r/20200527145843.2761782-1-mpe@ellerman.id.au
(cherry picked from commit 0828137e8f16721842468e33df0460044a0c588b) Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Xin Long [Mon, 10 Aug 2020 14:44:47 +0000 (16:44 +0200)]
xfrm: policy: match with both mark and mask on user interfaces
BugLink: https://bugs.launchpad.net/bugs/1890796
In commit ed17b8d377ea ("xfrm: fix a warning in xfrm_policy_insert_list"),
it would take 'priority' to make a policy unique, and allow duplicated
policies with different 'priority' to be added, which is not expected
by userland, as Tobias reported in strongswan.
To fix this duplicated policies issue, and also fix the issue in
commit ed17b8d377ea ("xfrm: fix a warning in xfrm_policy_insert_list"),
when doing add/del/get/update on user interfaces, this patch is to change
to look up a policy with both mark and mask by doing:
mark.v == pol->mark.v && mark.m == pol->mark.m
and leave the check:
(mark & pol->mark.m) == pol->mark.v
for tx/rx path only.
As the userland expects an exact mark and mask match to manage policies.
v1->v2:
- make xfrm_policy_mark_match inline and fix the changelog as
Tobias suggested.
Fixes: 295fae568885 ("xfrm: Allow user space manipulation of SPD mark") Fixes: ed17b8d377ea ("xfrm: fix a warning in xfrm_policy_insert_list") Reported-by: Tobias Brunner <tobias@strongswan.org> Tested-by: Tobias Brunner <tobias@strongswan.org> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
(cherry picked from commit 4f47e8ab6ab796b5380f74866fa5287aca4dcc58) Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Usage example:
devlink dev reload pci/0000:06:00.0
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
[Jeff Lane: dropped netns_change param from mlx5_devlink_reload_down
to conform to old devlink API]
(backported from commit 4383cfcc65e7879e1858da56954dae9fc20dfae9) Signed-off-by: Jeff Lane <jeffrey.lane@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
IB/mlx5: Load profile according to RoCE enablement state
BugLink: https://bugs.launchpad.net/bugs/1877270
When RoCE is disabled load mlx5_ib in raw_eth profile.
Clean pf_profile roce capability checks as it will not be used without
roce capability.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
(cherry picked from commit 94de879c28d8e6c20bfec308de84703625221712) Signed-off-by: Jeff Lane <jeffrey.lane@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1877270
Rename uplink_rep_profile and its unique init and cleanup stages to
suit its upcoming use as the profile when RoCE is disabled.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
(cherry picked from commit b5a498baf929a15536a4275967cf2377ad1b6015) Signed-off-by: Jeff Lane <jeffrey.lane@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1877270
Register "enable_roce" param, default value is RoCE enabled.
Current configuration is stored on mlx5_core_dev and exposed to user
through the cmode runtime devlink param.
Changing configuration requires changing the cmode driverinit devlink
param and calling devlink reload.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
(cherry picked from commit cc9defcbb8fae52810f7795b039223edae51ef95) Signed-off-by: Jeff Lane <jeffrey.lane@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
selftests/net: relax cpu affinity requirement in msg_zerocopy test
BugLink: https://bugs.launchpad.net/bugs/1812620
The msg_zerocopy test pins the sender and receiver threads to separate
cores to reduce variance between runs.
But it hardcodes the cores and skips core 0, so it fails on machines
with the selected cores offline, or simply fewer cores.
The test mainly gives code coverage in automated runs. The throughput
of zerocopy ('-z') and non-zerocopy runs is logged for manual
inspection.
Continue even when sched_setaffinity fails. Just log to warn anyone
interpreting the data.
Fixes: 07b65c5b31ce ("test: add msg_zerocopy test") Reported-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 16f6458f2478b55e2b628797bc81a4455045c74e linux-next) Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Ian May <ian.may@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
BugLink: https://launchpad.net/bugs/1890222
As stress-ng running SEC engine on the Ubuntu OS,
we found that SEC only supports two threads each with one TFM
based on the default module parameter 'ctx_q_num'.
If running more threads, stress-ng will fail since it cannot
get more TFMs.
In order to fix this, we adjusted the default values
of the module parameters to support more TFMs.
Signed-off-by: Longfang Liu <liulongfang@huawei.com> Signed-off-by: Zaibo Xu <xuzaibo@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
(cherry picked from commit 57b1aac1b426b7255afa195298ed691ffea204c6) Signed-off-by: Ike Panhc <ike.pan@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Signed-off-by: Ike Panhc <ike.pan@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
projects / mirror_ubuntu-focal-kernel.git / log