The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
When we remove an early section, we don't free the usage map, as the
usage maps of other sections are placed into the same page. Once the
section is removed, it is no longer an early section (especially, the
memmap is freed). When we re-add that section, the usage map is reused,
however, it is no longer an early section. When removing that section
again, we try to kfree() a usage map that was allocated during early
boot - bad.
Let's check against PageReserved() to see if we are dealing with an
usage map that was allocated during boot. We could also check against
!(PageSlab(usage_page) || PageCompound(usage_page)), but PageReserved() is
cleaner.
Can be triggered using memtrace under ppc64/powernv:
$ mount -t debugfs none /sys/kernel/debug/
$ echo 0x20000000 > /sys/kernel/debug/powerpc/memtrace/enable
$ echo 0x20000000 > /sys/kernel/debug/powerpc/memtrace/enable
------------[ cut here ]------------
kernel BUG at mm/slub.c:3969!
Oops: Exception in kernel mode, sig: 5 [#1]
LE PAGE_SIZE=3D64K MMU=3DHash SMP NR_CPUS=3D2048 NUMA PowerNV
Modules linked in:
CPU: 0 PID: 154 Comm: sh Not tainted 5.5.0-rc2-next-20191216-00005-g0be1dba7b7c0 #61
NIP kfree+0x338/0x3b0
LR section_deactivate+0x138/0x200
Call Trace:
section_deactivate+0x138/0x200
__remove_pages+0x114/0x150
arch_remove_memory+0x3c/0x160
try_remove_memory+0x114/0x1a0
__remove_memory+0x20/0x40
memtrace_enable_set+0x254/0x850
simple_attr_write+0x138/0x160
full_proxy_write+0x8c/0x110
__vfs_write+0x38/0x70
vfs_write+0x11c/0x2a0
ksys_write+0x84/0x140
system_call+0x5c/0x68
---[ end trace 4b053cbd84e0db62 ]---
The first invocation will offline+remove memory blocks. The second
invocation will first add+online them again, in order to offline+remove
them again (usually we are lucky and the exact same memory blocks will
get "reallocated").
Tested on powernv with boot memory: The usage map will not get freed.
Tested on x86-64 with DIMMs: The usage map will get freed.
Using Dynamic Memory under a Power DLAPR can trigger it easily.
Triggering removal (I assume after previously removed+re-added) of
memory from the HMC GUI can crash the kernel with the same call trace
and is fixed by this patch.
Link: http://lkml.kernel.org/r/20191217104637.5509-1-david@redhat.com Fixes: 326e1b8f83a4 ("mm/sparsemem: introduce a SECTION_IS_EARLY flag") Signed-off-by: David Hildenbrand <david@redhat.com> Tested-by: Pingfan Liu <piliu@redhat.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: Michal Hocko <mhocko@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If scrub returns an error we are not copying back the scrub arguments
structure to user space. This prevents user space to know how much
progress scrub has done if an error happened - this includes -ECANCELED
which is returned when users ask for scrub to stop. A particular use
case, which is used in btrfs-progs, is to resume scrub after it is
canceled, in that case it relies on checking the progress from the scrub
arguments structure and then use that progress in a call to resume
scrub.
So fix this by always copying the scrub arguments structure to user
space, overwriting the value returned to user space with -EFAULT only if
copying the structure failed to let user space know that either that
copying did not happen, and therefore the structure is stale, or it
happened partially and the structure is probably not valid and corrupt
due to the partial copy.
Reported-by: Graham Cobb <g.btrfs@cobb.uk.net> Link: https://lore.kernel.org/linux-btrfs/d0a97688-78be-08de-ca7d-bcb4c7fb397e@cobb.uk.net/ Fixes: 06fe39ab15a6a4 ("Btrfs: do not overwrite scrub error with fault error in scrub ioctl") CC: stable@vger.kernel.org # 5.1+ Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Qu Wenruo <wqu@suse.com> Tested-by: Graham Cobb <g.btrfs@cobb.uk.net> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We now use btrfs_can_overcommit() to see if we can flip a block group
read only. Before this would fail because we weren't taking into
account the usable un-allocated space for allocating chunks. With my
patches we were allowed to do the balance, which is technically correct.
The test is trying to start balance on degraded mount. So now we're
trying to allocate a chunk and cannot because we want to allocate a
RAID1 chunk, but there's only 1 device that's available for usage. This
results in an ENOSPC.
But we shouldn't even be making it this far, we don't have enough
devices to restripe. The problem is we're using btrfs_num_devices(),
that also includes missing devices. That's not actually what we want, we
need to use rw_devices.
The chunk_mutex is not needed here, rw_devices changes only in device
add, remove or replace, all are excluded by EXCL_OP mechanism.
Fixes: e4d8ec0f65b9 ("Btrfs: implement online profile changing") CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com>
[ add stacktrace, update changelog, drop chunk_mutex ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
[CAUSE]
All these call sites are only relying on root->reloc_root, which can
undergo btrfs_drop_snapshot(), and since we don't have real refcount
based protection to reloc roots, we can reach already dropped reloc
root, triggering KASAN.
[FIX]
To avoid such access to unstable root->reloc_root, we should check
BTRFS_ROOT_DEAD_RELOC_TREE bit first.
This patch introduces wrappers that provide the correct way to check the
bit with memory barriers protection.
Most callers don't distinguish merged reloc tree and no reloc tree. The
only exception is should_ignore_root(), as merged reloc tree can be
ignored, while no reloc tree shouldn't.
[CRITICAL SECTION ANALYSIS]
Although test_bit()/set_bit()/clear_bit() doesn't imply a barrier, the
DEAD_RELOC_TREE bit has extra help from transaction as a higher level
barrier, the lifespan of root::reloc_root and DEAD_RELOC_TREE bit are:
NULL: reloc_root is NULL PTR: reloc_root is not NULL
0: DEAD_RELOC_ROOT bit not set DEAD: DEAD_RELOC_ROOT bit set
(NULL, 0) Initial state __
| /\ Section A
btrfs_init_reloc_root() \/
| __
(PTR, 0) reloc_root initialized /\
| |
btrfs_update_reloc_root() | Section B
| |
(PTR, DEAD) reloc_root has been merged \/
| __
=== btrfs_commit_transaction() ====================
| /\
clean_dirty_subvols() |
| | Section C
(NULL, DEAD) reloc_root cleanup starts \/
| __
btrfs_drop_snapshot() /\
| | Section D
(NULL, 0) Back to initial state \/
Every have_reloc_root() or test_bit(DEAD_RELOC_ROOT) caller holds
transaction handle, so none of such caller can cross transaction boundary.
In Section A, every caller just found no DEAD bit, and grab reloc_root.
In the cross section A-B, caller may get no DEAD bit, but since reloc_root
is still completely valid thus accessing reloc_root is completely safe.
No test_bit() caller can cross the boundary of Section B and Section C.
In Section C, every caller found the DEAD bit, so no one will access
reloc_root.
In the cross section C-D, either caller gets the DEAD bit set, avoiding
access reloc_root no matter if it's safe or not. Or caller get the DEAD
bit cleared, then access reloc_root, which is already NULL, nothing will
be wrong.
The memory write barriers are between the reloc_root updates and bit
set/clear, the pairing read side is before test_bit.
Reported-by: Zygo Blaxell <ce3g8jdj@umail.furryterror.org> Fixes: d2311e698578 ("btrfs: relocation: Delay reloc tree deletion after merge_reloc_roots") CC: stable@vger.kernel.org # 5.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com>
[ barriers ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 96a2b03f281d ("mm, debug_pagelloc: use static keys to enable
debugging") has introduced a static key to reduce overhead when
debug_pagealloc is compiled in but not enabled. It relied on the
assumption that jump_label_init() is called before parse_early_param()
as in start_kernel(), so when the "debug_pagealloc=on" option is parsed,
it is safe to enable the static key.
However, it turns out multiple architectures call parse_early_param()
earlier from their setup_arch(). x86 also calls jump_label_init() even
earlier, so no issue was found while testing the commit, but same is not
true for e.g. ppc64 and s390 where the kernel would not boot with
debug_pagealloc=on as found by our QA.
To fix this without tricky changes to init code of multiple
architectures, this patch partially reverts the static key conversion
from 96a2b03f281d. Init-time and non-fastpath calls (such as in arch
code) of debug_pagealloc_enabled() will again test a simple bool
variable. Fastpath mm code is converted to a new
debug_pagealloc_enabled_static() variant that relies on the static key,
which is enabled in a well-defined point in mm_init() where it's
guaranteed that jump_label_init() has been called, regardless of
architecture.
[sfr@canb.auug.org.au: export _debug_pagealloc_enabled_early] Link: http://lkml.kernel.org/r/20200106164944.063ac07b@canb.auug.org.au Link: http://lkml.kernel.org/r/20191219130612.23171-1-vbabka@suse.cz Fixes: 96a2b03f281d ("mm, debug_pagelloc: use static keys to enable debugging") Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Matthew Wilcox <willy@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Qian Cai <cai@lca.pw> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently slab percpu vmstats are flushed twice: during the memcg
offlining and just before freeing the memcg structure. Each time percpu
counters are summed, added to the atomic counterparts and propagated up
by the cgroup tree.
The second flushing is required due to how recursive vmstats are
implemented: counters are batched in percpu variables on a local level,
and once a percpu value is crossing some predefined threshold, it spills
over to atomic values on the local and each ascendant levels. It means
that without flushing some numbers cached in percpu variables will be
dropped on floor each time a cgroup is destroyed. And with uptime the
error on upper levels might become noticeable.
The first flushing aims to make counters on ancestor levels more
precise. Dying cgroups may resume in the dying state for a long time.
After kmem_cache reparenting which is performed during the offlining
slab counters of the dying cgroup don't have any chances to be updated,
because any slab operations will be performed on the parent level. It
means that the inaccuracy caused by percpu batching will not decrease up
to the final destruction of the cgroup. By the original idea flushing
slab counters during the offlining should minimize the visible
inaccuracy of slab counters on the parent level.
The problem is that percpu counters are not zeroed after the first
flushing. So every cached percpu value is summed twice. It creates a
small error (up to 32 pages per cpu, but usually less) which accumulates
on parent cgroup level. After creating and destroying of thousands of
child cgroups, slab counter on parent level can be way off the real
value.
For now, let's just stop flushing slab counters on memcg offlining. It
can't be done correctly without scheduling a work on each cpu: reading
and zeroing it during css offlining can race with an asynchronous
update, which doesn't expect values to be changed underneath.
With this change, slab counters on parent level will become eventually
consistent. Once all dying children are gone, values are correct. And
if not, the error is capped by 32 * NR_CPUS pages per dying cgroup.
It's not perfect, as slab are reparented, so any updates after the
reparenting will happen on the parent level. It means that if a slab
page was allocated, a counter on child level was bumped, then the page
was reparented and freed, the annihilation of positive and negative
counter values will not happen until the child cgroup is released. It
makes slab counters different from others, and it might want us to
implement flushing in a correct form again. But it's also a question of
performance: scheduling a work on each cpu isn't free, and it's an open
question if the benefit of having more accurate counters is worth it.
We might also consider flushing all counters on offlining, not only slab
counters.
So let's fix the main problem now: make the slab counters eventually
consistent, so at least the error won't grow with uptime (or more
precisely the number of created and destroyed cgroups). And think about
the accuracy of counters separately.
Link: http://lkml.kernel.org/r/20191220042728.1045881-1-guro@fb.com Fixes: bee07b33db78 ("mm: memcontrol: flush percpu slab vmstats on kmem offlining") Signed-off-by: Roman Gushchin <guro@fb.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In Exynos542x/5800 SoCs, the G3D leaf clocks are located in the G3D power
domain. This is similar to the other hardware modules and their power
domains. However there is one thing specific to G3D clocks hierarchy.
Unlike other hardware modules, the G3D clocks hierarchy doesn't have any
gate clock between the TOP part of the hierarchy and the part located in
the power domain and some SoC internal busses are sourced directly from
the TOP muxes. The consequence of this design if the fact that the TOP
part of the hierarchy has to be enabled permanently to ensure proper
operation of the SoC power related components (G3D power domain and
Exynos Power Management Unit for system suspend/resume).
This patch adds an explicit call to clk_prepare_enable() on the last MUX
in the TOP part of G3D clock hierarchy to keep it enabled permanently to
ensure that the internal busses get their clock regardless of the main
G3D clock enablement status.
This fixes following imprecise abort issue observed on Odroid XU3/XU4
after enabling Panfrost driver by commit 1a5a85c56402 "ARM: dts: exynos:
Add Mali/GPU node on Exynos5420 and enable it on Odroid XU3/4"):
panfrost 11800000.gpu: clock rate = 400000000
panfrost 11800000.gpu: failed to get regulator: -517
panfrost 11800000.gpu: regulator init failed -517
Power domain G3D disable failed
...
panfrost 11800000.gpu: clock rate = 400000000
8<--- cut here ---
Unhandled fault: imprecise external abort (0x1406) at 0x00000000
pgd = (ptrval)
[00000000] *pgd=00000000
Internal error: : 1406 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 7 PID: 53 Comm: kworker/7:1 Not tainted 5.4.0-rc8-next-20191119-00032-g56f1001191a6 #6923
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
PC is at panfrost_gpu_soft_reset+0x94/0x110
LR is at ___might_sleep+0x128/0x2dc
...
[<c05c231c>] (panfrost_gpu_soft_reset) from [<c05c2704>] (panfrost_gpu_init+0x10/0x67c)
[<c05c2704>] (panfrost_gpu_init) from [<c05c15d0>] (panfrost_device_init+0x158/0x2cc)
[<c05c15d0>] (panfrost_device_init) from [<c05c0cb0>] (panfrost_probe+0x80/0x178)
[<c05c0cb0>] (panfrost_probe) from [<c05cfaa0>] (platform_drv_probe+0x48/0x9c)
[<c05cfaa0>] (platform_drv_probe) from [<c05cd20c>] (really_probe+0x1c4/0x474)
[<c05cd20c>] (really_probe) from [<c05cd694>] (driver_probe_device+0x78/0x1bc)
[<c05cd694>] (driver_probe_device) from [<c05cb374>] (bus_for_each_drv+0x74/0xb8)
[<c05cb374>] (bus_for_each_drv) from [<c05ccfa8>] (__device_attach+0xd4/0x16c)
[<c05ccfa8>] (__device_attach) from [<c05cc110>] (bus_probe_device+0x88/0x90)
[<c05cc110>] (bus_probe_device) from [<c05cc634>] (deferred_probe_work_func+0x4c/0xd0)
[<c05cc634>] (deferred_probe_work_func) from [<c0149df0>] (process_one_work+0x300/0x864)
[<c0149df0>] (process_one_work) from [<c014a3ac>] (worker_thread+0x58/0x5a0)
[<c014a3ac>] (worker_thread) from [<c0151174>] (kthread+0x12c/0x160)
[<c0151174>] (kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
Exception stack(0xee03dfb0 to 0xee03dff8)
...
Code: e594300ce5933020e3130c011a00000f (ebefff50).
---[ end trace badde2b74a65a540 ]---
In the above case, the Panfrost driver disables G3D clocks after failure
of getting the needed regulator and return with -EPROVE_DEFER code. This
causes G3D power domain disable failure and then, during second probe
an imprecise abort is triggered due to undefined power domain state.
Fixes: 45f10dabb56b ("clk: samsung: exynos5420: Add SET_RATE_PARENT flag to clocks on G3D path") Fixes: c9f7567aff31 ("clk: samsung: exynos542x: Move G3D subsystem clocks to its sub-CMU") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Link: https://lkml.kernel.org/r/20191216131407.17225-1-m.szyprowski@samsung.com Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Chanwoo Choi <cw00.choi@samsung.com> Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The new machine loader on z15 always creates an IPL Report block and
thus sets the IPL_PL_FLAG_IPLSR even when secure boot is disabled. This
causes the wrong message being printed at boot. Fix this by checking for
IPL_PL_FLAG_SIPL instead.
Fixes: 9641b8cc733f ("s390/ipl: read IPL report at early boot") Signed-off-by: Philipp Rudo <prudo@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On x86, until PAT is initialized, WC translates into UC-. Since we
calculate and store pgprot_writecombine(PAGE_KERNEL) when earlycon is
initialized, this means we actually use UC- mappings instead of WC
mappings, which makes scrolling very slow.
Instead store a boolean flag to indicate whether we want to use
writeback or write-combine mappings, and recalculate the actual pgprot_t
we need on every mapping. Once PAT is initialized, we will start using
write-combine mappings, which speeds up the scrolling considerably.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Fixes: 69c1f396f25b ("efi/x86: Convert x86 EFI earlyprintk into generic earlycon implementation") Link: https://lkml.kernel.org/r/20191224132909.102540-2-ardb@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
An Oops during the boot is found on some SNR machines. It turns out
this is because the snr_uncore_imc_freerunning_events[] array was
missing an end-marker.
Fixes: ee49532b38dd ("perf/x86/intel/uncore: Add IMC uncore support for Snow Ridge") Reported-by: Like Xu <like.xu@linux.intel.com> Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Tested-by: Like Xu <like.xu@linux.intel.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20200116200210.18937-1-kan.liang@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When CONFIG_SYSFS is disabled, but CONFIG_HOTPLUG_SMT is enabled,
the kernel fails to link:
arch/x86/power/cpu.o: In function `hibernate_resume_nonboot_cpu_disable':
(.text+0x38d): undefined reference to `cpuhp_smt_enable'
arch/x86/power/hibernate.o: In function `arch_resume_nosmt':
hibernate.c:(.text+0x291): undefined reference to `cpuhp_smt_enable'
hibernate.c:(.text+0x29c): undefined reference to `cpuhp_smt_disable'
Move the exported functions out of the #ifdef section into its
own with the correct conditions.
The patch that caused this is marked for stable backports, so
this one may need to be backported as well.
Fixes: ec527c318036 ("x86/power: Fix 'nosmt' vs hibernation triple fault during resume") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Jiri Kosina <jkosina@suse.cz> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191210195614.786555-1-arnd@arndb.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
As we reset the GPMI block at resume, the timing parameters setup by a
previous exec_op is lost. Rewriting GPMI timing registers on first exec_op
after resume fixes the problem.
This patch fixes a regression on setting up asynchronous commands to use
external trigger sources when board-specific routing information is
missing.
`ni_find_device_routes()` (called via `ni_assign_device_routes()`) finds
the table of register values for the device family and the set of valid
routes for the specific board. If both are found,
`tables->route_values` is set to point to the table of register values
for the device family and `tables->valid_routes` is set to point to the
list of valid routes for the specific board. If either is not found,
both `tables->route_values` and `tables->valid_routes` are left set at
their initial null values (initialized by `ni_assign_device_routes()`)
and the function returns `-ENODATA`.
Returning an error results in some routing functionality being disabled.
Unfortunately, leaving `table->route_values` set to `NULL` also breaks
the setting up of asynchronous commands that are configured to use
external trigger sources. Calls to `ni_check_trigger_arg()` or
`ni_check_trigger_arg_roffs()` while checking the asynchronous command
set-up would result in a null pointer dereference if
`table->route_values` is `NULL`. The null pointer dereference is fixed
in another patch, but it now results in failure to set up the
asynchronous command. That is a regression from the behavior prior to
commit 347e244884c3 ("staging: comedi: tio: implement global tio/ctr
routing") and commit 56d0b826d39f ("staging: comedi: ni_mio_common:
implement new routing for TRIG_EXT").
Change `ni_find_device_routes()` to set `tables->route_values` and/or
`tables->valid_routes` to valid information even if the other one can
only be set to `NULL` due to missing information. The function will
still return an error in that case. This should result in
`tables->valid_routes` being valid for all currently supported device
families even if the board-specific routing information is missing.
That should be enough to fix the regression on setting up asynchronous
commands to use external triggers for boards with missing routing
information.
Fixes: 347e244884c3 ("staging: comedi: tio: implement global tio/ctr routing") Fixes: 56d0b826d39f ("staging: comedi: ni_mio_common: implement new routing for TRIG_EXT"). Cc: <stable@vger.kernel.org> # 4.20+ Cc: Spencer E. Olson <olsonse@umich.edu> Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Link: https://lore.kernel.org/r/20200114182532.132058-3-abbotti@mev.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In `ni_find_route_source()`, `tables->route_values` gets dereferenced.
However it is possible that `tables->route_values` is `NULL`, leading to
a null pointer dereference. `tables->route_values` will be `NULL` if
the call to `ni_assign_device_routes()` during board initialization
returned an error due to missing device family routing information or
missing board-specific routing information. For example, there is
currently no board-specific routing information provided for the
PCIe-6251 board and several other boards, so those are affected by this
bug.
The bug is triggered when `ni_find_route_source()` is called via
`ni_check_trigger_arg()` or `ni_check_trigger_arg_roffs()` when checking
the arguments for setting up asynchronous commands. Fix it by returning
`-EINVAL` if `tables->route_values` is `NULL`.
Even with this fix, setting up asynchronous commands to use external
trigger sources for boards with missing routing information will still
fail gracefully. Since `ni_find_route_source()` only depends on the
device family routing information, it would be better if that was made
available even if the board-specific routing information is missing.
That will be addressed by another patch.
Fixes: 4bb90c87abbe ("staging: comedi: add interface to ni routing table information") Cc: <stable@vger.kernel.org> # 4.20+ Cc: Spencer E. Olson <olsonse@umich.edu> Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Link: https://lore.kernel.org/r/20200114182532.132058-2-abbotti@mev.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
IIO triggered buffer depends on IIO buffer which is missing from Kconfig
file. This should go unnoticed most of the time because there's a
chance something else has already enabled buffers. In some rare cases
though one might experience kbuild warnings about unmet direct
dependencies and build failures due to missing symbols.
Fix this by selecting IIO_BUFFER explicitly.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com> Fixes: a1d642266c14 ("iio: chemical: add support for Plantower PMS7003 sensor") Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
According to the data sheet the ambient sensor's scale is 0.12 lux/step
(not 0.024 lux/step as used by vcnl4200) when the integration time is
80ms. The integration time is currently hardcoded in the driver to that
value.
See p. 8 in https://www.vishay.com/docs/84307/designingvcnl4040.pdf
Fixes: 5a441aade5b3 ("iio: light: vcnl4000 add support for the VCNL4040 proximity and light sensor") Signed-off-by: Guido Günther <agx@sigxcpu.org> Reviewed-by: Marco Felsch <m.felsch@pengutronix.de> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
At the moment, attempting to probe a device with ST_LSM6DS3_ID
(e.g. using the st,lsm6ds3 compatible) fails with:
st_lsm6dsx_i2c 1-006b: unsupported whoami [69]
... even though 0x69 is the whoami listed for ST_LSM6DS3_ID.
This happens because st_lsm6dsx_check_whoami() also attempts
to match unspecified (zero-initialized) entries in the "id" array.
ST_LSM6DS3_ID = 0 will therefore match any entry in
st_lsm6dsx_sensor_settings (here: the first), because none of them
actually have all 12 entries listed in the "id" array.
Avoid this by additionally checking if "name" is set,
which is only set for valid entries in the "id" array.
Note: Although the problem was introduced earlier it did not surface until
commit 52f4b1f19679 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
because ST_LSM6DS3_ID was the first entry in st_lsm6dsx_sensor_settings.
Fixes: d068e4a0f921 ("iio: imu: st_lsm6dsx: add support to multiple devices with the same settings") Cc: <stable@vger.kernel.org> # 5.4 Acked-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch fixes device tree channel configuration.
ad7124 driver reads channels configuration from the device tree.
It expects to find channel specifications as child nodes.
Before this patch ad7124 driver assumed that the child nodes are parsed
by for_each_available_child_of_node in the order 0,1,2,3...
This is wrong and the real order of the children can be seen by running:
dtc -I fs /sys/firmware/devicetree/base on the machine.
For example, running this on an rpi 3B+ yields the real
children order: 4,2,0,7,5,3,1,6
Before this patch the driver assigned the channel configuration
like this:
- 0 <- 4
- 1 <- 2
- 2 <- 0
........
For example, the symptoms can be observed by connecting the 4th channel
to a 1V tension and then reading the in_voltage0-voltage19_raw sysfs
(multiplied of course by the scale) one would see that channel 0
measures 1V and channel 4 measures only noise.
Now the driver uses the reg property of each child in order to
correctly identify to which channel the parsed configuration
belongs to.
Fixes b3af341bbd966: ("iio: adc: Add ad7124 support") Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
One of the uses of the external clock outputs is to provide a stable
32768 Hz clock signal to WiFi and Bluetooth chips. On the R40, the RTC
has an internal RC oscillator that is muxed with the external crystal.
Allow setting the parent rate for the external clock outputs so that
requests for 32768 Hz get passed to the RTC's clock driver to mux in
the external crystal if it isn't already muxed correctly.
Fixes: cd030a78f7aa ("clk: sunxi-ng: support R40 SoC") Fixes: 01a7ea763fc4 ("clk: sunxi-ng: r40: Force LOSC parent to RTC LOSC output") Cc: <stable@kernel.org> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a quirk for the Irbis NB41 netbook was added, to override the defaults
for this device, I forgot to add/keep the BYT_CHT_ES8316_SSP0 part of the
defaults, completely breaking audio on this netbook.
This commit adds the BYT_CHT_ES8316_SSP0 flag to the Irbis NB41 netbook
quirk, making audio work again.
Cc: stable@vger.kernel.org Cc: russianneuromancer@ya.ru Fixes: aa2ba991c420 ("ASoC: Intel: bytcht_es8316: Add quirk for Irbis NB41 netbook") Reported-and-tested-by: russianneuromancer@ya.ru Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20200106113903.279394-1-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
According to arm cpus binding doc,
"
On 32-bit ARM v7 or later systems this property is
required and matches the CPU MPIDR[23:0] register
bits.
Bits [23:0] in the reg cell must be set to
bits [23:0] in MPIDR.
All other bits in the reg cell must be set to 0.
"
In i.MX7ULP, the MPIDR[23:0] is 0xf00, not 0, so fix it.
Otherwise there will be warning:
"DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map"
In stm32_afsdm_pcm_cb function, the transfer size is provided in bytes.
However, samples are copied as 16 bits words from iio buffer.
Divide by two the transfer size, to copy the right number of samples.
Fixes: 1e7f6e1c69f0 ("ASoC: stm32: dfsdm: add 16 bits audio record support") Signed-off-by: Olivier Moysan <olivier.moysan@st.com> Link: https://lore.kernel.org/r/20200110131131.3191-1-olivier.moysan@st.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In current driver, locks can be taken as follows:
- Register access: take a lock on regmap config and then on clock.
- Master clock provider: take a lock on clock and then on regmap config.
This can lead to the circular locking summarized below.
Remove peripheral clock management through regmap framework, and manage
peripheral clock in driver instead. On register access, lock on clock
is taken first, which allows to avoid possible locking issue.
Commit d878970f6ce1 ("bus: ti-sysc: Add separate functions for handling
clocks") separated handling of optional clocks from the main clocks, but
introduced an issue where we do not necessarily allocate a slot for both
fck and ick clocks, but still assume fixed slots for enumerating over the
clocks.
Let's fix the issue by ensuring we always have slots for both fck and ick
even if we don't use ick, and don't attempt to enumerate optional clocks
if not allocated.
In the long run we might want to simplify things a bit by only allocating
space only for the optional clocks as we have only few devices with
optional clocks.
Fixes: d878970f6ce1 ("bus: ti-sysc: Add separate functions for handling clocks") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Using SDMA1 with UART1 is causing a "Timeout waiting for CH0" error.
This patch changes to ahb clock from SDMA1_ROOT to AHB which
fixes the timeout error.
Fixes: a05ea40eb384 ("arm64: dts: imx: Add i.mx8mm dtsi support") Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since i2c_smbus functions can sleep, the brightness setting function
for this driver must be the blocking version to avoid scheduling while
atomic.
Signed-off-by: Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/r/20191106200106.29519-2-eajames@linux.ibm.com Fixes: ef9e1cdf419a3 ("hwmon: (pmbus/cffps) Add led class device for power supply fault led") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Those regulators are not actually supported by the AB8500 regulator
driver. There is no ab8500_regulator_info for them and no entry in
ab8505_regulator_match.
As such, they cannot be registered successfully, and looking them
up in ab8505_regulator_match causes an out-of-bounds array read.
Fixes: 547f384f33db ("regulator: ab8500: add support for ab8505") Cc: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20191106173125.14496-2-stephan@gerhold.net Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since there are some DIE which has only ranges instead of the
combination of entrypc/highpc, address verification must use
dwarf_haspc() instead of dwarf_entrypc/dwarf_highpc.
Also, the ranges only DIE will have a partial code in different section
(e.g. unlikely code will be in text.unlikely as "FUNC.cold" symbol). In
that case, we can not use dwarf_entrypc() or die_entrypc(), because the
offset from original DIE can be a minus value.
Instead, this simply gets the symbol and offset from symtab.
Without this patch;
# perf probe -D clear_tasks_mm_cpumask:1
Failed to get entry address of clear_tasks_mm_cpumask
Error: Failed to add events.
This patch fixes an unintended sign extension on left shifts. From Colin
King: "Shifting a u8 left will cause the value to be promoted to an
integer. If the top bit of the u8 is set then the following conversion to
an u64 will sign extend the value causing the upper 32 bits to be set in
the result."
Fix this by using get_unaligned_be*() instead.
Fixes: bf8162354233 ("[SCSI] add scsi trace core functions and put trace points") Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Link: https://lore.kernel.org/r/20191101211447.187151-1-bvanassche@acm.org Reported-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In qla2x00_find_all_fabric_devs(), fcport->flags & FCF_LOGIN_NEEDED is a
necessary condition for logging into new rports, but not for dropping lost
ones.
Fixes: 726b85487067 ("qla2xxx: Add framework for async fabric discovery") Link: https://lore.kernel.org/r/20191122221912.20100-2-martin.wilck@suse.com Tested-by: David Bond <dbond@suse.com> Signed-off-by: Martin Wilck <mwilck@suse.com> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 4fa183455988 ("scsi: qla2xxx: Utilize pci_alloc_irq_vectors/
pci_free_irq_vectors calls.") use pci_alloc_irq_vectors() to replace
pci_enable_msi() but it didn't handle the return value correctly. This bug
make qla2x00 always fail to setup MSI if MSI-X fail, so fix it.
BTW, improve the log message of return value in qla2x00_request_irqs() to
avoid confusion.
Fixes: 4fa183455988 ("scsi: qla2xxx: Utilize pci_alloc_irq_vectors/pci_free_irq_vectors calls.") Cc: Michael Hernandez <michael.hernandez@cavium.com> Link: https://lore.kernel.org/r/1574314847-14280-1-git-send-email-chenhc@lemote.com Signed-off-by: Huacai Chen <chenhc@lemote.com> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Print the string for which conversion failed instead of printing the
function name twice.
Fixes: 2650d71e244f ("target: move transport ID handling to the core") Cc: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20191107215525.64415-1-bvanassche@acm.org Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The member hba->pcidev may be used after its reference is dropped. Move the
put function to where it is never used to avoid potential use after free
issues.
Fixes: a77171806515 ("[SCSI] bnx2i: Removed the reference to the netdev->base_addr") Link: https://lore.kernel.org/r/1573043541-19126-1-git-send-email-bianpan2016@163.com Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The variable init_fw_cb is released twice, resulting in a double free
bug. The call to the function dma_free_coherent() before goto is removed to
get rid of potential double free.
Fixes: 2a49a78ed3c8 ("[SCSI] qla4xxx: added IPv6 support.") Link: https://lore.kernel.org/r/1572945927-27796-1-git-send-email-bianpan2016@163.com Signed-off-by: Pan Bian <bianpan2016@163.com> Acked-by: Manish Rangankar <mrangankar@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 60e4cf67a58 (reiserfs: fix extended attributes on the root
directory) introduced a regression open_xa_root started returning
-EOPNOTSUPP but it was not handled properly in reiserfs_for_each_xattr.
When the reiserfs module is built without CONFIG_REISERFS_FS_XATTR,
deleting an inode would result in a warning and chowning an inode
would also result in a warning and then fail to complete.
With CONFIG_REISERFS_FS_XATTR enabled, the xattr root would always be
present for read-write operations.
This commit handles -EOPNOSUPP in the same way -ENODATA is handled.
Fixes: 60e4cf67a582 ("reiserfs: fix extended attributes on the root directory") CC: stable@vger.kernel.org # Commit 60e4cf67a58 was picked up by stable Link: https://lore.kernel.org/r/20200115180059.6935-1-jeffm@suse.com Reported-by: Michael Brunnbauer <brunni@netestate.de> Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Due to the use of sizeof(), command size set for the spi transfer
was wrong. Driver was sending and receiving always 1 byte less
and especially on write, it was hanging.
echo -n -e "\\x1\\x2\\x3\\x4" > /dev/mtd1
And read part too now works as expected.
hexdump -C -n16 /dev/mtd1 00000000 01 02 03 04 ab f3 ad c2 ab e3 f4 36 dd 38 04 15 00000010
Fixes: 4379075a870b ("mtd: mchp23k256: Add support for mchp23lcv1024") Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 951d48855d86 ("of: Make of_dma_get_range() work on bus nodes")
reworked the logic such that of_dma_get_range() works correctly
starting from a bus node containing "dma-ranges".
Since on Juno we don't have a SoC level bus node and "dma-ranges" is
present only in the root node, we get the following error:
OF: translation of DMA address(0) to CPU address failed node(/sram@2e000000)
OF: translation of DMA address(0) to CPU address failed node(/uart@7ff80000)
...
OF: translation of DMA address(0) to CPU address failed node(/mhu@2b1f0000)
OF: translation of DMA address(0) to CPU address failed node(/iommu@2b600000)
OF: translation of DMA address(0) to CPU address failed node(/iommu@2b600000)
OF: translation of DMA address(0) to CPU address failed node(/iommu@2b600000)
So let's fix it by dropping the "dma-ranges" property for now. This
should be fine since it doesn't represent any kind of device-visible
restriction; it was only there for completeness, and we've since given
in to the assumption that missing "dma-ranges" implies a 1:1 mapping
anyway.
We can add it later with a proper SoC bus node and moving all the
devices that belong there along with the "dma-ranges" if required.
Fixes: 193d00a2b35e ("arm64: dts: juno: add dma-ranges property") Cc: Rob Herring <robh+dt@kernel.org> Cc: Liviu Dudau <liviu.dudau@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.0-rc7+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Use READ_ONCE() and WRITE_ONCE() to annotate this expected race.
Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20191205045619.204946-1-edumazet@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
arch/arm/dts/meson-gxl-s905x-khadas-vim.dtb: Warning (avoid_unnecessary_addr_size):
/gpio-keys-polled: unnecessary #address-cells/#size-cells
without "ranges" or child "reg" property
Fixes: e15d2774b8c0 ("ARM64: dts: meson-gxl: add support for the Khadas VIM board") Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
At the time commit ce5ec440994b ("tcp: ensure epoll edge trigger
wakeup when write queue is empty") was added to the kernel,
we still had a single write queue, combining rtx and write queues.
Once we moved the rtx queue into a separate rb-tree, testing
if sk_write_queue is empty has been suboptimal.
Indeed, if we have packets in the rtx queue, we probably want
to delay the EPOLLOUT generation at the time incoming packets
will free them, making room, but more importantly avoiding
flooding application with EPOLLOUT events.
Solution is to use tcp_rtx_and_write_queues_empty() helper.
Fixes: 75c119afe14f ("tcp: implement rb-tree based retransmit queue") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jason Baron <jbaron@akamai.com> Cc: Neal Cardwell <ncardwell@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
../drivers/block/xen-blkfront.c:1117:4: warning: misleading indentation;
statement is not part of the previous 'if' [-Wmisleading-indentation]
nr_parts = PARTS_PER_DISK;
^
../drivers/block/xen-blkfront.c:1115:3: note: previous statement is here
if (err)
^
This is because there is a space at the beginning of this line; remove
it so that the indentation is consistent according to the Linux kernel
coding style and clang no longer warns.
While we are here, the previous line has some trailing whitespace; clean
that up as well.
mlxsw configures Spectrum in such a way that BUM traffic is passed not
through its nominal traffic class TC, but through its MC counterpart TC+8.
However, when collecting statistics, Qdiscs only look at the nominal TC and
ignore the MC TC.
Add two helpers to compute the value for logical TC from the constituents,
one for backlog, the other for tail drops. Use them throughout instead of
going through the xstats pointer directly.
Counters for TX bytes and packets are deduced from packet priority
counters, and therefore already include BUM traffic. wred_drop counter is
irrelevant on MC TCs, because RED is not enabled on them.
Fixes: 7b8195306694 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports") Signed-off-by: Petr Machata <petrm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Per-port counter cache used by Qdiscs is updated periodically, unless the
port is down. The fact that the cache is not updated for down ports is no
problem for most counters, which are relative in nature. However, backlog
is absolute in nature, and if there is a non-zero value in the cache around
the time that the port goes down, that value just stays there. This value
then leaks to offloaded Qdiscs that report non-zero backlog even if
there (obviously) is no traffic.
The HW does not keep backlog of a downed port, so do likewise: as the port
goes down, wipe the backlog value from xstats.
Fixes: 075ab8adaf4e ("mlxsw: spectrum: Collect tclass related stats periodically") Signed-off-by: Petr Machata <petrm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When adding the sh_eth_cpu_data::dual_port flag I forgot to add the flag
checks to __sh_eth_get_regs(), causing the non-existing TSU registers to
be dumped by 'ethtool' on the single port Ether controllers having TSU...
Fixes: a94cf2a614f8 ("sh_eth: fix TSU init on SH7734/R8A7740") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the packet pointed to by retransmit_skb_hint is unlinked by ACK,
retransmit_skb_hint will be set to NULL in tcp_clean_rtx_queue().
If packet loss is detected at this time, retransmit_skb_hint will be set
to point to the current packet loss in tcp_verify_retransmit_hint(),
then the packets that were previously marked lost but not retransmitted
due to the restriction of cwnd will be skipped and cannot be
retransmitted.
To fix this, when retransmit_skb_hint is NULL, retransmit_skb_hint can
be reset only after all marked lost packets are retransmitted
(retrans_out >= lost_out), otherwise we need to traverse from
tcp_rtx_queue_head in tcp_xmit_retransmit_queue().
Packetdrill to demonstrate:
// Disable RACK and set max_reordering to keep things simple
0 `sysctl -q net.ipv4.tcp_recovery=0`
+0 `sysctl -q net.ipv4.tcp_max_reordering=3`
// Send 8 data segments
+0 write(4, ..., 8000) = 8000
+0 > P. 1:8001(8000) ack 1
// Enter recovery and 1:3001 is marked lost
+.01 < . 1:1(0) ack 1 win 257 <sack 3001:4001,nop,nop>
+0 < . 1:1(0) ack 1 win 257 <sack 5001:6001 3001:4001,nop,nop>
+0 < . 1:1(0) ack 1 win 257 <sack 5001:7001 3001:4001,nop,nop>
// Retransmit 1:1001, now retransmit_skb_hint points to 1001:2001
+0 > . 1:1001(1000) ack 1
// 1001:2001 was ACKed causing retransmit_skb_hint to be set to NULL
+.01 < . 1:1(0) ack 2001 win 257 <sack 5001:8001 3001:4001,nop,nop>
// Now retransmit_skb_hint points to 4001:5001 which is now marked lost
// BUG: 2001:3001 was not retransmitted
+0 > . 2001:3001(1000) ack 1
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com> Acked-by: Neal Cardwell <ncardwell@google.com> Tested-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add missing endpoint sanity check to probe in order to prevent a
NULL-pointer dereference (or slab out-of-bounds access) when retrieving
the interrupt-endpoint bInterval on ndo_open() in case a device lacks
the expected endpoints.
Fixes: 40a82917b1d3 ("net/usb/r8152: enable interrupt transfer") Cc: hayeswang <hayeswang@realtek.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There is a bug in ptp_clock_unregister(), where ptp_cleanup_pin_groups()
first frees ptp->pin_{,dev_}attr, but then posix_clock_unregister() needs
them to destroy a related sysfs device.
These functions can not be just swapped, as posix_clock_unregister() frees
ptp which is needed in the ptp_cleanup_pin_groups(). Fix this by calling
ptp_cleanup_pin_groups() in ptp_clock_release(), right before ptp is freed.
This makes this patch fix an UAF bug in a patch which fixes an UAF bug.
Reported-by: Antti Laakso <antti.laakso@intel.com> Fixes: a33121e5487b ("ptp: fix the race between the release of ptp_clock and cdev") Link: https://lore.kernel.org/netdev/3d2bd09735dbdaf003585ca376b7c1e5b69a19bd.camel@intel.com/ Signed-off-by: Vladis Dronov <vdronov@redhat.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Array utdm_info is declared as an array of MAX_HDLC_NUM (4) elements
however up to UCC_MAX_NUM (8) elements are potentially being written
to it. Currently we have an array out-of-bounds write error on the
last 4 elements. Fix this by making utdm_info UCC_MAX_NUM elements in
size.
Addresses-Coverity: ("Out-of-bounds write") Fixes: c19b6d246a35 ("drivers/net: support hdlc function for QE-UCC") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
lan78xx_tx_bh() makes sure to not exceed MAX_SINGLE_PACKET_SIZE
bytes in the aggregated packets it builds, but does
nothing to prevent large GSO packets being submitted.
Pierre-Francois reported various hangs when/if TSO is enabled.
For localy generated packets, we can use netif_set_gso_max_size()
to limit the size of TSO packets.
Note that forwarded packets could still hit the issue,
so a complete fix might require implementing .ndo_features_check
for this driver, forcing a software segmentation if the size
of the TSO packet exceeds MAX_SINGLE_PACKET_SIZE.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: RENARD Pierre-Francois <pfrenard@gmail.com> Tested-by: RENARD Pierre-Francois <pfrenard@gmail.com> Cc: Stefan Wahren <stefan.wahren@i2se.com> Cc: Woojung Huh <woojung.huh@microchip.com> Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When there is not enough memory and napi_alloc_skb() return NULL,
the HNS driver will print error message, and than try again, if
the memory is not enough for a while, huge error message and the
retry operation will cause soft lockup.
When napi_alloc_skb() return NULL because of no memory, we can
get a warn_alloc() call trace, so this patch deletes the error
message. We already use polling mode to handle irq, but the
retry operation will render the polling weight inactive, this
patch just return budget when the rx is not completed to avoid
dead loop.
Fixes: 36eedfde1a36 ("net: hns: Optimize hns_nic_common_poll for better performance") Fixes: b5996f11ea54 ("net: add Hisilicon Network Subsystem basic ethernet support") Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
DSA subsystem takes care of netdev statistics since commit 4ed70ce9f01c
("net: dsa: Refactor transmit path to eliminate duplication"), so
any accounting inside tagger callbacks is redundant and can lead to
messing up the stats.
This bug is present in Qualcomm tagger since day 0.
Fixes: cafdc45c949b ("net-next: dsa: add Qualcomm tag RX/TX handler") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexander Lobakin <alobakin@dlink.ru> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
rndis_filter_device_add() allocates an instance of struct rndis_device
which never gets deallocated as rndis_filter_device_remove() sets
net_device->extension which points to the rndis_device struct to NULL,
leaving the rndis_device dangling.
Since net_device->extension is eventually freed in free_netvsc_device(),
we refrain from setting it to NULL inside rndis_filter_device_remove()
Signed-off-by: Mohammed Gamal <mgamal@redhat.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
I missed the fact that macvlan_broadcast() can be used both
in RX and TX.
skb_eth_hdr() makes only sense in TX paths, so we can not
use it blindly in macvlan_broadcast()
Fixes: 96cc4b69581d ("macvlan: do not assume mac_header is set in macvlan_broadcast()") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Jurgen Van Ham <juvanham@gmail.com> Tested-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The distributed arp table is using a DHT to store and retrieve MAC address
information for an IP address. This is done using unicast messages to
selected peers. The potential peers are looked up using the IP address and
the VID.
While the IP address is always stored in big endian byte order, this is not
the case of the VID. It can (depending on the host system) either be big
endian or little endian. The host must therefore always convert it to big
endian to ensure that all devices calculate the same peers for the same
lookup data.
Fixes: be1db4f6615b ("batman-adv: make the Distributed ARP Table vlan aware") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The driver was doing a synchronous uninterruptible bulk-transfer without
using a timeout. This could lead to the driver hanging on probe due to a
malfunctioning (or malicious) device until the device is physically
disconnected. While sleeping in probe the driver prevents other devices
connected to the same hub from being added to (or removed from) the bus.
An arbitrary limit of five seconds should be more than enough.
Fixes: dbafc28955fa ("NFC: pn533: don't send USB data off of the stack") Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A missing generation check during DELTABLE processing causes it to queue
the DELFLOWTABLE operation a second time, so we corrupt the list here:
case NFT_MSG_DELFLOWTABLE:
list_del_rcu(&nft_trans_flowtable(trans)->list);
nf_tables_flowtable_notify(&trans->ctx,
because we have two different DELFLOWTABLE transactions for the same
flowtable. We then call list_del_rcu() twice for the same flowtable->list.
The object handling seems to suffer from the same bug so add a generation
check too and only queue delete transactions for flowtables/objects that
are still active in the next generation.
This patch fixes a WARN_ON in nft_set_destroy() due to missing
set reference count drop from the preparation phase. This is triggered
by the module autoload path. Do not exercise the abort path from
nft_request_module() while preparation phase cleaning up is still
pending.
An earlier commit (1b789577f655060d98d20e,
"netfilter: arp_tables: init netns pointer in xt_tgchk_param struct")
fixed missing net initialization for arptables, but turns out it was
incomplete. We can get a very similar struct net NULL deref during
error unwinding:
map->members is freed by ip_set_free() right before using it in
mtype_ext_cleanup() again. So we just have to move it down.
Reported-by: syzbot+4c3cc6dbe7259dbf9054@syzkaller.appspotmail.com Fixes: 40cd63bf33b2 ("netfilter: ipset: Support extensions which need a per data destroy function") Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The fragments attached to a skb can be part of a compound page. In that case,
page_ref_inc will increment the refcount for the wrong page. Fix this by
using get_page instead, which calls page_ref_inc on the compound head and
also checks for overflow.
Fixes: 2b67f944f88c ("cfg80211: reuse existing page fragments in A-MSDU rx") Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20200113182107.20461-1-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Meaning, the visible effect is very similar to f54c7898ed1c ("bpf: Fix
precision tracking for unbounded scalars"), that is, the fall-through
branch in the instruction 5 is considered to be never taken given the
conclusion from the min/max bounds tracking in w6, and therefore the
dead-code sanitation rewrites it as goto pc-1. However, real-life input
disagrees with verification analysis since a soft-lockup was observed.
The bug sits in the analysis of the ARSH. The definition is that we shift
the target register value right by K bits through shifting in copies of
its sign bit. In adjust_scalar_min_max_vals(), we do first coerce the
register into 32 bit mode, same happens after simulating the operation.
However, for the case of simulating the actual ARSH, we don't take the
mode into account and act as if it's always 64 bit, but location of sign
bit is different:
Consider an unknown R0 where bpf_get_socket_cookie() (or others) would
for example return 0xffff. With the above ARSH simulation, we'd see the
following results:
In insn 3, we have a runtime value of 0xcfb40000, which is '1100 1111 1011
0100 0000 0000 0000 0000', the result after the shift has 0xe7da0000 that
is '1110 0111 1101 1010 0000 0000 0000 0000', where the sign bit is correctly
retained in 32 bit mode. In insn4, the umax was 0xffffffff, and changed into
0x7ffbfff8 after the shift, that is, '0111 1111 1111 1011 1111 1111 1111 1000'
and means here that the simulation didn't retain the sign bit. With above
logic, the updates happen on the 64 bit min/max bounds and given we coerced
the register, the sign bits of the bounds are cleared as well, meaning, we
need to force the simulation into s32 space for 32 bit alu mode.
Verification after the fix below. We're first analyzing the fall-through branch
on 32 bit signed >= test eventually leading to rejection of the program in this
specific case:
Patch series "Fix two above-47bit hint address vs. THP bugs".
The two get_unmapped_area() implementations have to be fixed to provide
THP-friendly mappings if above-47bit hint address is specified.
This patch (of 2):
Filesystems use thp_get_unmapped_area() to provide THP-friendly
mappings. For DAX in particular.
Normally, the kernel doesn't create userspace mappings above 47-bit,
even if the machine allows this (such as with 5-level paging on x86-64).
Not all user space is ready to handle wide addresses. It's known that
at least some JIT compilers use higher bits in pointers to encode their
information.
Userspace can ask for allocation from full address space by specifying
hint address (with or without MAP_FIXED) above 47-bits. If the
application doesn't need a particular address, but wants to allocate
from whole address space it can specify -1 as a hint address.
Unfortunately, this trick breaks thp_get_unmapped_area(): the function
would not try to allocate PMD-aligned area if *any* hint address
specified.
Modify the routine to handle it correctly:
- Try to allocate the space at the specified hint address with length
padding required for PMD alignment.
- If failed, retry without length padding (but with the same hint
address);
- If the returned address matches the hint address return it.
- Otherwise, align the address as required for THP and return.
The user specified hint address is passed down to get_unmapped_area() so
above-47bit hint address will be taken into account without breaking
alignment requirements.
Link: http://lkml.kernel.org/r/20191220142548.7118-2-kirill.shutemov@linux.intel.com Fixes: b569bab78d8d ("x86/mm: Prepare to expose larger address space to userspace") Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reported-by: Thomas Willhalm <thomas.willhalm@intel.com> Tested-by: Dan Williams <dan.j.williams@intel.com> Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.vnet.ibm.com> Cc: "Bruggeman, Otto G" <otto.g.bruggeman@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
XGMAC supports maximum MTU that can go to 16KB. Lets add this check in
the calculation of RX buffer size.
Fixes: 7ac6653a085b ("stmmac: Move the STMicroelectronics driver") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The 16KB RX Buffer must also be 16 byte aligned. Fix it.
Fixes: 7ac6653a085b ("stmmac: Move the STMicroelectronics driver") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The EDIMM STARTER KIT i.Core 1.5 MIPI Evaluation is based on
the 1.5 version of the i.Core MX6 cpu module. The 1.5 version
differs from the original one for a few details, including the
ethernet PHY interface clock provider.
With this commit, the ethernet interface works properly:
SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver
While before using the 1.5 version, ethernet failed to startup
do to un-clocked PHY interface:
fec 2188000.ethernet eth0: could not attach to PHY
Similar fix has merged for i.Core MX6Q but missed to update for DL.
Patch series "use div64_ul() instead of div_u64() if the divisor is
unsigned long".
We were first inspired by commit b0ab99e7736a ("sched: Fix possible divide
by zero in avg_atom () calculation"), then refer to the recently analyzed
mm code, we found this suspicious place.
201 if (min) {
202 min *= this_bw;
203 do_div(min, tot_bw);
204 }
And we also disassembled and confirmed it:
/usr/src/debug/kernel-4.9.168-016.ali3000/linux-4.9.168-016.ali3000.alios7.x86_64/mm/page-writeback.c: 201
0xffffffff811c37da <__wb_calc_thresh+234>: xor %r10d,%r10d
0xffffffff811c37dd <__wb_calc_thresh+237>: test %rax,%rax
0xffffffff811c37e0 <__wb_calc_thresh+240>: je 0xffffffff811c3800 <__wb_calc_thresh+272>
/usr/src/debug/kernel-4.9.168-016.ali3000/linux-4.9.168-016.ali3000.alios7.x86_64/mm/page-writeback.c: 202
0xffffffff811c37e2 <__wb_calc_thresh+242>: imul %r8,%rax
/usr/src/debug/kernel-4.9.168-016.ali3000/linux-4.9.168-016.ali3000.alios7.x86_64/mm/page-writeback.c: 203
0xffffffff811c37e6 <__wb_calc_thresh+246>: mov %r9d,%r10d ---> truncates it to 32 bits here
0xffffffff811c37e9 <__wb_calc_thresh+249>: xor %edx,%edx
0xffffffff811c37eb <__wb_calc_thresh+251>: div %r10
0xffffffff811c37ee <__wb_calc_thresh+254>: imul %rbx,%rax
0xffffffff811c37f2 <__wb_calc_thresh+258>: shr $0x2,%rax
0xffffffff811c37f6 <__wb_calc_thresh+262>: mul %rcx
0xffffffff811c37f9 <__wb_calc_thresh+265>: shr $0x2,%rdx
0xffffffff811c37fd <__wb_calc_thresh+269>: mov %rdx,%r10
This series uses div64_ul() instead of div_u64() if the divisor is
unsigned long, to avoid truncation to 32-bit on 64-bit platforms.
This patch (of 3):
The variables 'min' and 'max' are unsigned long and do_div truncates
them to 32 bits, which means it can test non-zero and be truncated to
zero for division. Fix this issue by using div64_ul() instead.
Link: http://lkml.kernel.org/r/20200102081442.8273-2-wenyang@linux.alibaba.com Fixes: 693108a8a667 ("writeback: make bdi->min/max_ratio handling cgroup writeback aware") Signed-off-by: Wen Yang <wenyang@linux.alibaba.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Qian Cai <cai@lca.pw> Cc: Tejun Heo <tj@kernel.org> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
(gdb) l *(btrfs_find_all_roots_safe+0x41)
0x8d7e1 is in btrfs_find_all_roots_safe (fs/btrfs/backref.c:1413).
1408
1409 tmp = ulist_alloc(GFP_NOFS);
1410 if (!tmp)
1411 return -ENOMEM;
1412 *roots = ulist_alloc(GFP_NOFS);
1413 if (!*roots) {
1414 ulist_free(tmp);
1415 return -ENOMEM;
1416 }
1417
Following the lifetime of the allocated 'roots' ulist, it gets freed
again in btrfs_qgroup_account_extent().
But this does not happen if the function is called with the
'BTRFS_FS_QUOTA_ENABLED' flag cleared, then btrfs_qgroup_account_extent()
does a short leave and directly returns.
Instead of directly returning we should jump to the 'out_free' in order to
free all resources as expected.
btrfs_del_root_ref() will simply WARN_ON() if the ref doesn't match in
any way, and then continue to delete the reference. This shouldn't
happen, we have these values because there's more to the reference than
the original root and the sub root. If any of these checks fail, return
-ENOENT.
CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
btrfs sub create A
btrfs sub create A/B
btrfs sub snap A C
mkdir C/foo
mv A/B C/foo
rm -rf *
We will end up with a transaction abort.
The reason for this is because we create a root ref for B pointing to A.
When we create a snapshot of C we still have B in our tree, but because
the root ref points to A and not C we will make it appear to be empty.
The problem happens when we move B into C. This removes the root ref
for B pointing to A and adds a ref of B pointing to C. When we rmdir C
we'll see that we have a ref to our root and remove the root ref,
despite not actually matching our reference name.
Now btrfs_del_root_ref() allowing this to work is a bug as well, however
we know that this inode does not actually point to a root ref in the
first place, so we shouldn't be calling btrfs_del_root_ref() in the
first place and instead simply look up our dir index for this item and
do the rest of the removal.
CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
btrfs_unlink_subvol takes the name of the dentry and the root objectid
based on what kind of inode this is, either a real subvolume link or a
empty one that we inherited as a snapshot. We need to fix how we unlink
in the case for BTRFS_EMPTY_SUBVOL_DIR_OBJECTID in the future, so rework
btrfs_unlink_subvol to just take the dentry and handle getting the right
objectid given the type of inode this is. There is no functional change
here, simply pushing the work into btrfs_unlink_subvol() proper.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The root cause is that the IOMMU subsystem runs before the workqueue
subsystem, which the variable 'wq_online' is still 'false'. This leads
to the statement 'if (WARN_ON(!wq_online))' in flush_workqueue() is
'true'.
Since the variable 'memcg_kmem_cache_wq' is not allocated during the
time, it is unnecessary to call flush_memcg_workqueue(). This prevents
the WARNING message triggered by flush_workqueue().
Link: http://lkml.kernel.org/r/20200103085503.1665-1-ahuang12@lenovo.com Fixes: 92ee383f6daab ("mm: fix race between kmem_cache destroy, create and deactivate") Signed-off-by: Adrian Huang <ahuang12@lenovo.com> Reported-by: Xiaochun Lee <lixc17@lenovo.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Cc: Joerg Roedel <jroedel@suse.de> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Shmem/tmpfs tries to provide THP-friendly mappings if huge pages are
enabled. But it doesn't work well with above-47bit hint address.
Normally, the kernel doesn't create userspace mappings above 47-bit,
even if the machine allows this (such as with 5-level paging on x86-64).
Not all user space is ready to handle wide addresses. It's known that
at least some JIT compilers use higher bits in pointers to encode their
information.
Userspace can ask for allocation from full address space by specifying
hint address (with or without MAP_FIXED) above 47-bits. If the
application doesn't need a particular address, but wants to allocate
from whole address space it can specify -1 as a hint address.
Unfortunately, this trick breaks THP alignment in shmem/tmp:
shmem_get_unmapped_area() would not try to allocate PMD-aligned area if
*any* hint address specified.
This can be fixed by requesting the aligned area if the we failed to
allocated at user-specified hint address. The request with inflated
length will also take the user-specified hint address. This way we will
not lose an allocation request from the full address space.
[kirill@shutemov.name: fold in a fixup] Link: http://lkml.kernel.org/r/20191223231309.t6bh5hkbmokihpfu@box Link: http://lkml.kernel.org/r/20191220142548.7118-3-kirill.shutemov@linux.intel.com Fixes: b569bab78d8d ("x86/mm: Prepare to expose larger address space to userspace") Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: "Willhalm, Thomas" <thomas.willhalm@intel.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: "Bruggeman, Otto G" <otto.g.bruggeman@intel.com> Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.vnet.ibm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We observed an issue that was some extra columns displayed after switching
perf data file in browser. The steps to reproduce:
1. perf record -a -e cycles,instructions -- sleep 3
2. perf report --group
3. In browser, we use hotkey 's' to switch to another perf.data
4. Now in browser, the extra columns 'Self' and 'Children' are displayed.
The issue is setup_sorting() executed again after repeat path, so dimensions
are added again.
This patch checks the last key returned from __cmd_report(). If it's
K_SWITCH_INPUT_DATA, skips the setup_sorting().
Fixes: ad0de0971b7f ("perf report: Enable the runtime switching of perf data file") Signed-off-by: Jin Yao <yao.jin@linux.intel.com> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Feng Tang <feng.tang@intel.com> Cc: Jin Yao <yao.jin@intel.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20191220013722.20592-1-yao.jin@linux.intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
set_cache_qos_cfg() is leaking memory when the given level is not
RDT_RESOURCE_L3 or RDT_RESOURCE_L2. At the moment, this function is
called with only valid levels but move the allocation after the valid
level checks in order to make it more robust and future proof.
Fix build error:
./drivers/gpu/drm/i915/selftests/i915_random.h: In function i915_prandom_u32_max_state:
./drivers/gpu/drm/i915/selftests/i915_random.h:48:23: error:
implicit declaration of function mul_u32_u32; did you mean mul_u64_u32_div? [-Werror=implicit-function-declaration]
return upper_32_bits(mul_u32_u32(prandom_u32_state(state), ep_ro));
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: 7ce5b6850b47 ("drm/i915/selftests: Use mul_u32_u32() for 32b x 32b -> 64b result") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20200107135014.36472-1-yuehaibing@huawei.com
(cherry picked from commit 62bf5465b26d1f502430b9c654be7d16bf2e242d) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The EFI mixed mode entry code goes through the ordinary startup_32()
routine before jumping into the kernel's EFI boot code in 64-bit
mode. The 32-bit startup code must be entered with paging disabled,
but this is not documented as a requirement for the EFI handover
protocol, and so we should disable paging explicitly when entering
the kernel from 32-bit EFI firmware.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Cc: <stable@vger.kernel.org> Cc: Arvind Sankar <nivedita@alum.mit.edu> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Link: https://lkml.kernel.org/r/20191224132909.102540-4-ardb@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the SME and SEV features are present via CPUID, but memory encryption
support is not enabled (MSR 0xC001_0010[23]), the feature flags are cleared
using clear_cpu_cap(). However, if get_cpu_cap() is later called, these
feature flags will be reset back to present, which is not desired.
Change from using clear_cpu_cap() to setup_clear_cpu_cap() so that the
clearing of the flags is maintained.
A system that supports resource monitoring may have multiple resources
while not all of these resources are capable of monitoring. Monitoring
related state is initialized only for resources that are capable of
monitoring and correspondingly this state should subsequently only be
removed from these resources that are capable of monitoring.
domain_add_cpu() calls domain_setup_mon_state() only when r->mon_capable
is true where it will initialize d->mbm_over. However,
domain_remove_cpu() calls cancel_delayed_work(&d->mbm_over) without
checking r->mon_capable resulting in an attempt to cancel d->mbm_over on
all resources, even those that never initialized d->mbm_over because
they are not capable of monitoring. Hence, it triggers a debugobjects
warning when offlining CPUs because those timer debugobjects are never
initialized:
ODEBUG: assert_init not available (active state 0) object type:
timer_list hint: 0x0
WARNING: CPU: 143 PID: 789 at lib/debugobjects.c:484
debug_print_object
Hardware name: HP Synergy 680 Gen9/Synergy 680 Gen9 Compute Module, BIOS I40 05/23/2018
RIP: 0010:debug_print_object
Call Trace:
debug_object_assert_init
del_timer
try_to_grab_pending
cancel_delayed_work
resctrl_offline_cpu
cpuhp_invoke_callback
cpuhp_thread_fun
smpboot_thread_fn
kthread
ret_from_fork
- D+ goes high, Host starts running by remote wakeup
- D+ is not stable, goes low
- Host requests GetPortStatus at (*1) and gets the following hub status:
- Current Connect Status bit is 0
- Connect Status Change bit is 1
- D+ stabilizes, goes high
- Host requests ClearPortFeature and thus Connect Status Change bit is
cleared at (*2)
- After waiting 100 ms, Host starts the Interrupt Transfer at (*3)
- Since the Connect Status Change bit is 0, Hub returns NAK.
In this case, port_event() is not called in hub_event() and Host cannot
recognize device. To solve this issue, flag change_bits even if only
Connect Status Change bit is 1 when got in the first GetPortStatus.
This issue occurs rarely because it only if D+ changes during a very
short time between GetPortStatus and ClearPortFeature. However, it is
fatal if it occurs in embedded system.
Commit 69f594a38967 ("ptrace: do not audit capability check when outputing /proc/pid/stat")
introduced the ability to opt out of audit messages for accesses to various
proc files since they are not violations of policy. While doing so it
somehow switched the check from ns_capable() to
has_ns_capability{_noaudit}(). That means it switched from checking the
subjective credentials of the task to using the objective credentials. This
is wrong since. ptrace_has_cap() is currently only used in
ptrace_may_access() And is used to check whether the calling task (subject)
has the CAP_SYS_PTRACE capability in the provided user namespace to operate
on the target task (object). According to the cred.h comments this would
mean the subjective credentials of the calling task need to be used.
This switches ptrace_has_cap() to use security_capable(). Because we only
call ptrace_has_cap() in ptrace_may_access() and in there we already have a
stable reference to the calling task's creds under rcu_read_lock() there's
no need to go through another series of dereferences and rcu locking done
in ns_capable{_noaudit}().
As one example where this might be particularly problematic, Jann pointed
out that in combination with the upcoming IORING_OP_OPENAT feature, this
bug might allow unprivileged users to bypass the capability checks while
asynchronously opening files like /proc/*/mem, because the capability
checks for this would be performed against kernel credentials.
To illustrate on the former point about this being exploitable: When
io_uring creates a new context it records the subjective credentials of the
caller. Later on, when it starts to do work it creates a kernel thread and
registers a callback. The callback runs with kernel creds for
ktask->real_cred and ktask->cred. To prevent this from becoming a
full-blown 0-day io_uring will call override_cred() and override
ktask->cred with the subjective credentials of the creator of the io_uring
instance. With ptrace_has_cap() currently looking at ktask->real_cred this
override will be ineffective and the caller will be able to open arbitray
proc files as mentioned above.
Luckily, this is currently not exploitable but will turn into a 0-day once
IORING_OP_OPENAT{2} land in v5.6. Fix it now!
Cc: Oleg Nesterov <oleg@redhat.com> Cc: Eric Paris <eparis@redhat.com> Cc: stable@vger.kernel.org Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Serge Hallyn <serge@hallyn.com> Reviewed-by: Jann Horn <jannh@google.com> Fixes: 69f594a38967 ("ptrace: do not audit capability check when outputing /proc/pid/stat") Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>