Ville Syrjälä [Fri, 10 Jan 2014 12:06:47 +0000 (14:06 +0200)]
drm/i915: Fix 915GM self-refresh enable/disable
INSTPM is a masked register so use the _MASKED_BIT_{ENABLE,DISABLE}
macros when enabling/disabling self-refresh on 915GM.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 10 Jan 2014 12:06:46 +0000 (14:06 +0200)]
drm/i915: 830M doesn't have an LVDS port
There's no LVDS port on 830M so don't go reading the LVDS control
register.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 10 Jan 2014 12:06:45 +0000 (14:06 +0200)]
drm/i915: No panel fitter on 830M or non-mobile gen2/3 platforms
PFIT_CONTROL doesn't exist on 830M, so avoid reading it in
i9xx_get_pfit_config().
Also assume that only mobile gen2/3 chipsets have a panel fitter. This
matches the documentation, but I didn't have real hardware to verify.
Gen4 docmentation is a bit inconsistent, but experimenetation on my
LPT machine suggests that the panel fitter is available on non-mobile
gen4 platforms. At least on this machine panel fitter appears works
just fine even on VGA output.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Deepak S [Fri, 10 Jan 2014 09:48:26 +0000 (15:18 +0530)]
drm/i915/vlv: Add drpc debugfs support for valleyview
Many of the fields from Gen6 have gone away for vlv. Strip all those
fields that are not relevent and try to update fields that we care
about. This patch give information about current RP & RC status and
individual Wells.
v2: Move Render & Media Well status to separate lines (Ville)
Signed-off-by: Deepak S <deepak.s@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Thu, 9 Jan 2014 15:08:16 +0000 (17:08 +0200)]
drm/i915: vlv: W/a for hotplug/manual VGA detection
VGA detection requires the reference clock to be on, so make sure this
is the case.
This fixes VGA hotplug/manual detection where all pipes are off and so
we would normally disable all clocks.
v2:
- Instead of disabling PSR clock gating, force the reference clock on
through the DPLL_A register. (Kin Chan S <kin.s.chan@intel.com>)
v3:
- Move enabling of the clock to intel_reset_dpio() and use the DPLL_B
register instead, where we already have a similar tweak for the CRI
clock. (Ville)
Reported-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Thu, 9 Jan 2014 15:08:15 +0000 (17:08 +0200)]
drm/i915: vlv: make CRI clock enabling explicit during resume
intel_init_dpio() isn't called during resume, so we won't set the CRI
clock enable bit during that time. Move the enabling to
intel_reset_dpio() instead.
Note that the HW reset value for this bit is 1, so probably this patch
won't make any difference. We should still make the setting explicit,
since BIOS could change things under us.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 8 Jan 2014 14:18:23 +0000 (14:18 +0000)]
drm/i915: Introduce new intel_output_name()
That we can use for debugging purposes.
v2: Use designated initializers for the 'names' array (Paulo Zanoni,
Jani Nikula).
Add a check in case the array has a hole (which can now remain
unnoticed with designated initializers) (Jani Nikula)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (for v1) Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Tue, 7 Jan 2014 16:55:53 +0000 (14:55 -0200)]
drm/i915: don't set modes for 2 connectors on the same encoder
In some cases we have more than 1 connector associated to an encoder
(e.g., SDVO, Haswell DP/HDMI) and we can only set a mode for one of
these connectors. If we only allowed modesets for connected connectors
we would never need this patch, but since we do allow modeset for
disconnected connectors we may see user space trying to set modes on
the two connectors attached to the same encoder, so we need to forbid
that.
This problem can be reproduced by running the following
intel-gpu-tools test case:
./kms_setmode --run-subtest clone-exclusive-crtc
Thanks to Daniel Vetter for providing a version of this patch on
pastebin.
Credits-to: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Sat, 14 Dec 2013 22:38:30 +0000 (20:38 -0200)]
drm/i915: i830M has watermarks like i855
So shuffle the checks around a bit. Also give all the structs and
functions proper prefixes: i830_ for the dual-pipe mobile platforms
and i845_ for the two single-pipe desktop platforms.
Note that the max fifo value isn't actually correct for the i830M, but
since we don't frob the fifo split we don't actually need it. This is
different for some gen3 devices where we need the full fifo for self
refresh mode.
Cc: Thomas Richter <richter@rus.uni-stuttgart.de> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Fri, 10 Jan 2014 07:50:12 +0000 (08:50 +0100)]
drm/i915: Drop I915_ prefix from HAS_FBC
My OCD just couldn't let this slide. Spotted while reviewing Ville's
patch to only flip planes when we have FBC.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 7 Jan 2014 14:15:37 +0000 (16:15 +0200)]
drm/i915: Don't swap planes on 830M
Looks like 830M doesn't quite like it when you try to move a plane from
one pipe to another. It seems that the plane's old pipe has to be active
even if the plane is already disabled, otherwise the relevant register
just won't accept new values.
caused a regression on 830M. It will attempt to swap the planes when the
driver is loaded, but at that time only pipe A might be active, so plane
A gets disabled, but plane B won't get enabled since pipe B is not
active when we try to move the plane over to pipe A.
There's no reason to swap planes on 830M since it doesn't support
FBC. Change the logic a bit to limit the plane swapping to platforms
which actually support FBC. This should avoid getting a black screen on
830M.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Wed, 8 Jan 2014 13:12:28 +0000 (11:12 -0200)]
drm/i915: fix wrong PLL debug messages.
LPT does have PCH refclk, but it's different form the IBX/CPT/PPT one
and doesn't use the same structs. It is wrong to have a message saying
that "LPT does not has PCH refclk" (sic). While at it, signal that we
only want this function on IBX/CPT/PPT by renaming it and adding a
WARN.
On HSW we also print "0 shared PLLs initialized", but we *do* have
shared PLLs on HSW (LCPLL, WRPLL, SPLL) and we *do* initialize them.
We just don't use "struct intel_shared_dpll". So remove the debug
message.
In the future we may want to rename all that "intel shared pll" code
to "ibx shared pll", but I'll leave this to another patch.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse Barnes [Tue, 7 Jan 2014 21:30:45 +0000 (13:30 -0800)]
drm/i915/bdw: don't try to check IPS state on BDW v2
According to Art, we don't have a way to read back the state reliably at
runtime, through the control reg or the mailbox, at least not without risking
disabling it again. So drop the readout and checking on BDW.
v2: drop TODO comment (Paulo)
move POSTING_READ of control reg under HSW branch in disable (Paulo)
always report IPS as enabled on BDW (Paulo)
References: https://bugs.freedesktop.org/show_bug.cgi?id=71906 Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So it seems to have been missed both in the fastboot patch and in the
3d mode suppport (where only crtc_htotal reflects the real pipe
width).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add note based on Ville's review.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse Barnes [Thu, 19 Dec 2013 18:48:01 +0000 (10:48 -0800)]
drm/i915: fix fastboot pfit disable hack to update pipe w/h
When fastbooting, we read out the pipe timings early on, and then in a
panel fitted config, disable the fitter later. But we weren't updating
the pipe src h/w, which meant the mouse cursor was clipped to the
pfitted size rather than the native size set later. Fix that up so the
cursor is visible in the new mode.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Avoid duplicating the same piece of code several times by separating
the watemark vfunc setup from the init_clock_gating vfunc setup on PCH
platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 7 Jan 2014 14:14:09 +0000 (16:14 +0200)]
drm/i915: Enable watermarks for BDW
We forgot to intialize the watermark vfuncs for BDW, and hence the
watermarks were never updated.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 7 Jan 2014 14:14:08 +0000 (16:14 +0200)]
drm/i915: Fix watermark code for BDW
Looks like I forgot to update the ILK/SNB/IVB watermark patches to deal
with BDW. Add the relevant BDW checks to make sure we take the HSW
codepaths on BDW as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 20 Dec 2013 17:09:41 +0000 (15:09 -0200)]
drm/i915: avoid unclaimed registers when capturing the error state
We're iterating over the CPU transcoders, so check for the correct
power domain.
This fixes many "unclaimed register" error messages.
This can be reproduced by the IGT test mentioned below, but we still
get a FAIL when we run it.
Testcase: igt/kms_lip/flip-vs-panning-vs-hang Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Thu, 2 Jan 2014 14:32:35 +0000 (14:32 +0000)]
drm/i915: Flush outstanding requests before allocating new seqno
In very rare cases (such as a memory failure stress test) it is possible
to fill the entire ring without emitting a request. Under this
circumstance, the outstanding request is flushed and waited upon. After
space on the ring is cleared, we return to emitting the new command -
except that we just cleared the seqno allocated for this operation and
trigger the sanity check that a request is only ever emitted with a
valid seqno. The fix is to rearrange the code to make sure the
allocation of the seqno for this operation is after any required flushes
of outstanding operations.
The bug exists since the preallocation was introduced in
commit 9d7730914f4cd496e356acfab95b41075aa8eae8
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Nov 27 16:22:52 2012 +0000
drm/i915: Preallocate next seqno before touching the ring
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Tue, 31 Dec 2013 15:50:31 +0000 (15:50 +0000)]
drm/i915: Avoid dereference past end of page array in gen8_ppgtt_insert_entries()
The bug from gen6_ppgtt_insert_entries() was replicated into
gen8_ppgtt_insert_entries(). This applies the fix for the OOPS from the
previous patch to the gen8 routine.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Ben Widawsky <benjamin.widawsky@intel.com> Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This bug dates back to the original introduction of the
gen6_ppgtt_insert_entries()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Ben Widawsky <benjamin.widawsky@intel.com> Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Dropped cc: stable since without full ppgtt there's no way
we'll access the last page directory with this function since that
range is occupied (only in the allocator) with the ppgtt pdes. Without
aliasing we can start to use that range and blow up.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
we added the workaround, but never emitted any debug message that it was
active. Doing so should help identify known performance regressions.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tetsuo Handa [Fri, 3 Jan 2014 11:42:18 +0000 (20:42 +0900)]
drm/i915: Fix refcount leak and possible NULL pointerdereference.
Since get_pid_task() grabs a reference on the task_struct, we have to drop the
refcount after reading that task's comm name. Use pid_task() with RCU instead.
Also, avoid directly reading like pid_task()->comm because
pid_task() will return NULL if the task have already exit()ed.
This patch fixes both problems.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Tue, 17 Dec 2013 22:42:11 +0000 (23:42 +0100)]
drm/i915: grab a pages pin count for preallocate stolen
But only when we indeed set up a gtt mapping. We need this since the
vma also holds a pages_pin_count, on top of the unconditional
pages_pin_count we grab for all stolen objects (to avoid swap-out).
This should avoid a pages_pin_count underrun when cleaning up
framebuffers objects taken over from the BIOS.
Chris mentioned in his review that this bug even predates the vma
conversion.
Reported-by: Jesse Barnes <jbarnes@virtuousgeek.org> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Cc: Ben Widawsky <benjamin.widawsky@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Tue, 17 Dec 2013 12:46:36 +0000 (14:46 +0200)]
drm/i915: s/haswell_update_wm/ilk_update_wm/
We use this hook starting from ILK onwards, so change the prefix
accordingly. Also rename functions/struct names used from
haswell_update_wm that are relevant to ILK already.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Tue, 17 Dec 2013 12:46:35 +0000 (14:46 +0200)]
drm/i915: remove unused WM defines
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Tue, 17 Dec 2013 12:46:34 +0000 (14:46 +0200)]
drm/i915: simplify platform specific code in hsw_write_wm_values
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 5 Dec 2013 13:51:31 +0000 (15:51 +0200)]
Revert "drm/i915/sprite: Always enable the scaler on IronLake"
Apparently always enabling the sprite scaler magically made
sprites work on ILK in the past.
I think the real reason for the failure was missing sprite
watermark programming, and enabling the scaler effectively
disabled LP1+ watermarks, which was enough to keep things going.
Or it might be that the hardware more or less ignores watermarks
for scaled sprites since things seem to work even if I leave
sprite watermarks at 0 and disable all other planes except the
sprite.
In any case, we left the scaler always on but then failed to
check whether we might be exceeding the scaler's source size
limits. That caused the sprite to fail when a sufficiently
large unscaled image was being displayed.
Now that we're getting proper watermark programming for ILK, we
can keep the scaler disabled unless we need to do actual scaling.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 5 Dec 2013 13:51:41 +0000 (15:51 +0200)]
drm/i915: Avoid underruns when disabling sprites
As the watermark registers aren't double bufferd, clearing the
watermarks immediately after writing the sprite registers can be
hazardous.
Until we have something better, add a wait for vblank between the
two steps to make sure the sprite no longer needs the watermark
levels before we clear them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 5 Dec 2013 13:51:40 +0000 (15:51 +0200)]
drm/i915: Don't disable primary when color keying is used
When color keying is used, the primary may not be invisible even though
the sprite fully covers it. So check for color keying before deciding to
disable the primary plane.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 5 Dec 2013 13:51:39 +0000 (15:51 +0200)]
drm/i915: Try to fix the messy IVB sprite scaling workaround
We now have a very clear method of disabling LP1+ wartermarks,
and we can actually detect if we actually did disable them, or
if they were already disabled. Use that to clean up the
WaCxSRDisabledForSpriteScaling:ivb handling.
I was hoping to apply the workaround in a way that wouldn't
require a blocking wait, but sadly IVB really does appear to
require LP1+ watermarks to be off for an entire frame before
enabling sprite scaling. Simply disabling LP1+ watermarks
during the previous frame is not enough, no matter how early
in the frame we do it :(
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 5 Dec 2013 13:51:38 +0000 (15:51 +0200)]
drm/i915: Move ILK/SNB/IVB over to the HSW WM code
The new HSW watermark code can now handle ILK/SNB/IVB as well, so
switch them over. Kill the old code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 5 Dec 2013 13:51:37 +0000 (15:51 +0200)]
drm/i915: Disable LP1+ watermarks safely in init
ILK doesn't like if we just write the LP1+ watermarks registers with 0.
We need to just disable the watermarks by clearing the enable bit. Use
that method also when disabling LP1+ watermarks in init_clock_gating.
It looks like disabling the sprite LP1 watermarks can cause underruns
even if we just toggle the WM1S_LP_EN bit. So treat that bit like the
actual watermark numbers and avoid setting it to 0 immediately.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 5 Dec 2013 13:51:36 +0000 (15:51 +0200)]
drm/i915: Linetime watermarks are a HSW feature
Linetime watermarks don't exist on ILK/SNB/IVB, so don't compute them
except on HSW.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 5 Dec 2013 13:51:35 +0000 (15:51 +0200)]
drm/i915: Disable FBC WM on ILK, and disable LP2+ when FBC is enabled
ILK has a bunch of issues with FBC. First of all, BSpec tells us that
FBC WM should never be enabled. Secondly when FBC is enabled
with FBC WM disabled, LP2+ watermarks must be disabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 5 Dec 2013 13:51:34 +0000 (15:51 +0200)]
drm/i915: Don't merge LP1+ watermarks on ILK/SNB/IVB when multiple pipes are enabled
Multi-pipe LP1+ watermarks are a HSW+ feature, so let's not do it on
earlier generations.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 5 Dec 2013 13:51:33 +0000 (15:51 +0200)]
drm/i915: Fix LP1+ watermark disabling ILK
On ILK disabling LP1+ watermarks must be done carefully to avoid
underruns. If we just write 0 to the register in the middle of the scan
cycle we often get an underrun. So instead we have to leave the actual
watermark levels in the register intact, and just toggle the enable bit.
Presumably the hardware takes a while to get out of low power mode, and
so the watermark level need to stay valid until that time.
We also have to be careful with the WM1S_LP_EN bit. It seems the
hardware more or less treats it like the actual watermarks numbers, and
so we must not toggle it too soon. Just leave it alone when disabling
the LP1+ watermarks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 5 Dec 2013 13:51:32 +0000 (15:51 +0200)]
drm/i915: Fix LP1 sprite watermarks for ILK/SNB
ILK/SNB don't have LP2+ watermarks for sprites. Also the LP1 sprite
watermark register has its own enable bit. Take these differences
into account when programming the LP1+ registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 5 Dec 2013 13:51:30 +0000 (15:51 +0200)]
drm/i915: Avoid computing invalid WM levels when sprites/scaling is enabled
On ILK/SNB only LP0/1 watermarks can be enabled when sprites are
enabled, and on ILK/SNB/IVB sprite scaling is limited to LP0 only.
So we can avoid computing the extra levels we're never going to use.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 5 Dec 2013 13:51:29 +0000 (15:51 +0200)]
drm/i915: Add ILK/SNB/IVB WM latency field support
Add a new function ilk_wm_lp_latency() which will tell us what to write
into the WM_LPx register latency field. HSW is different from erlier
gens in this regard.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 5 Dec 2013 13:51:28 +0000 (15:51 +0200)]
drm/i915: Add IVB DDB partitioning control
On IVB the display data buffer partitioning control lives in the
DISP_ARB_CTL2 register. Add the relevant defines/code for it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Tue, 17 Dec 2013 09:00:54 +0000 (10:00 +0100)]
drm/i915: kick firmware fbs even when i915 fbdev is disabled
Otherwise we don't kick out firmware framebuffers like vesafb and
efifb when CONFIG_DRM_I915_FBDEV=n but CONFIG_FB=y.
There's still the pesky issue with vgacon which we should somehow
replace with the dummy console at least. We have a similar issue at
module un/reload, since vgacon state is terminally botched after
i915.ko has loaded in modeset mode. But this gets us a step further at
least.
v2: Use IS_ENABLED - I always get this wrong for tristates. Spotted by
Jani.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Jani Nikula <jani.nikula@linux.intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Tue, 17 Dec 2013 04:50:38 +0000 (20:50 -0800)]
drm/i915: Don't emit mbox updates without semaphores
Aside from the fact that it leaves confusing dumps on error capture, it
is entirely unnecessary, and potentially harmful in cases like BDW,
where the instruction has changed.
In reality (seemingly), this will have no behavioral impact.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse Barnes [Tue, 17 Dec 2013 00:34:23 +0000 (16:34 -0800)]
drm/i915/vlv: add early DPIO init v3
Just add an early init since we may need to access DPIO regs early on.
The init call in modeset_init_hw is also needed for the resume case,
when we need to reset DPIO to keep things happy.
v2: split reset and reg init
v3: split patches (Daniel)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wei Yongjun [Mon, 16 Dec 2013 06:13:25 +0000 (14:13 +0800)]
drm/i915: fix return value check of debugfs_create_file()
In case of error, the function debugfs_create_file() returns NULL
pointer not ERR_PTR() if debugfs is enabled. The IS_ERR() test in
the return value check should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 13 Dec 2013 17:22:31 +0000 (15:22 -0200)]
drm/i915: release the GTT mmaps when going into D3
So we'll get a fault when someone tries to access the mmap, then we'll
wake up from D3.
v2: - Rebase
v3: - Use gtt active/inactive
Testcase: igt/pm_pc8/gem-mmap-gtt Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add comment + WARN as discussed with Paulo on irc.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Thu, 12 Dec 2013 23:28:04 +0000 (15:28 -0800)]
drm/i915/bdw: Implement ff workarounds
WaVSRefCountFullforceMissDisable and
WaDSRefCountFullforceMissDisable
VS is a carry-over from HSW, and DS is likely not used by anyone yet.
Cc: Kenneth Graunke <kenneth@whitecape.org> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Line of 106 chars is too long. Really.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 13 Dec 2013 11:26:20 +0000 (13:26 +0200)]
drm/i915/bdw: Don't use forcewake needlessly
Not all registers need forcewake even if they're not shadowed.
Add the missing check to gen8_writeX() to avoid needless forcewake
usage when writing eg. display registers.
v2: Use straight up <0x40000 check instead of NEEDS_FORCE_WAKE()
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 3 Dec 2013 09:30:09 +0000 (11:30 +0200)]
drm/i915: Clear out old GT FIFO errors in intel_uncore_early_sanitize()
The BIOS or someone else might have done something bad and there
might be old GT FIFO erros reported in GTFIFODBG. Clear those out
in intel_uncore_early_sanitize() to make sure we don't mistake them
for our problems.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Thu, 12 Dec 2013 15:54:42 +0000 (17:54 +0200)]
drm/i915: dont call irq_put when irq test is on
If test is running, irq_get was not called so we should gain
balance by not doing irq_put
"So the rule is: if you access unlocked values, you use ACCESS_ONCE().
You don't say "but it can't matter". Because you simply don't know."
-- Linus
v2: use local variable so it can't change during test (Chris)
v3: update commit msg and use ACCESS_ONCE (Ville)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 12 Dec 2013 15:27:40 +0000 (17:27 +0200)]
drm/i915: Rework the FBC interval/stall stuff a bit
Don't touch DPFC_RECOMP_CTL on FBC2, use RMW to update
the FBC_CONTROL on FBC1 to make it easier for people to
experiment with different numbers. Also fix the interval
mask for FBC1.
v2: Rebased
Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 28 Nov 2013 15:30:02 +0000 (17:30 +0200)]
drm/i915: Enable FBC for all mobile gen2 and gen3 platforms
All mobile gen2 and gen3 chipsets should have FBC1, and the code
should now handle them all. So just set has_fbc=true for all such
chipsets.
Note that fbc is still disabled by default for now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 28 Nov 2013 15:29:57 +0000 (17:29 +0200)]
drm/i915: FBC_CONTROL2 is gen4 only
Gen2 and gen3 don't have the FBC_CONTROL2 register, so don't
touch it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 28 Nov 2013 15:29:56 +0000 (17:29 +0200)]
drm/i915: Gen2 FBC1 CFB pitch wants 32B units
On gen2 the compressed frame buffer pitch is specified in 32B units
rather than the 64B units used on gen3+.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Mon, 25 Nov 2013 17:27:08 +0000 (15:27 -0200)]
drm/i915: split intel_ddi_pll_mode_set in 2 pieces
The first piece, intel_ddi_pll_select, finds a PLL and assigns it to
the CRTC, but doesn't write any register. It can also fail in case it
doesn't find a PLL.
The second piece, intel_ddi_pll_enable, uses the information stored by
intel_ddi_pll_select to actually enable the PLL by writing to its
register. This function can't fail. We also have some refcount sanity
checks here.
The idea is that one day we'll remove all the functions that touch
registers from haswell_crtc_mode_set to haswell_crtc_enable, so we'll
call intel_ddi_pll_select at haswell_crtc_mode_set and then call
intel_ddi_pll_enable at haswell_crtc_enable. Since I'm already
touching this code, let's take care of this particular split today.
v2: - Clock on the debug message is in KHz
- Add missing POSTING_READ
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Bikeshed comments.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Tue, 10 Dec 2013 15:02:43 +0000 (17:02 +0200)]
drm/i915: Fix timeout with missed interrupts in __wait_seqno
Commit 094f9a54e355 ("drm/i915: Fix __wait_seqno to use true infinite
timeouts") added support for __wait_seqno to detect missing interrupts and
go around them by polling. As there is also timeout detection in
__wait_seqno, the polling and timeout detection were done with the same
timer.
When there has been missed interrupts and polling is needed, the timer is
set to trigger in (now + 1) jiffies in future, instead of the caller
specified timeout.
Now when io_schedule() returns, we calculate the jiffies left to timeout
using the timer expiration value. As the current jiffies is now bound to be
always equal or greater than the expiration value, the timeout_jiffies will
become zero or negative and we return -ETIME to caller even tho the
timeout was never reached.
Fix this by decoupling timeout calculation from timer expiration.
v2: Commit message with some sense in it (Chris Wilson)
v3: add parenthesis on timeout_expire calculation
v4: don't read jiffies without timeout (Chris Wilson)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Wed, 11 Dec 2013 20:50:10 +0000 (18:50 -0200)]
drm/i915: touch VGA MSR after we enable the power well
Fixes regression introduced by:
commit bf51d5e2cda5d36d98e4b46ac7fca9461e512c41
Author: Paulo Zanoni <paulo.r.zanoni at intel.com>
Date: Wed Jul 3 17:12:13 2013 -0300
drm/i915: switch disable_power_well default value to 1
The bug I'm seeing can be reproduced with:
- Have vgacon configured/enabled
- Make sure the power well gets disabled, then enabled. You can
check this by seeing the messages print by hsw_set_power_well
- Stop your display manager
- echo 0 > /sys/class/vtconsole/vtcon1/bind
I can easily reproduce this by blacklising snd_hda_intel and booting
with eDP+HDMI.
If you do this and then look at dmesg, you'll see we're printing
infinite "Unclaimed register" messages. This is happening because
we're stuck on an infinite loop inside console_unlock(), which is
calling many functions from vgacon.c. And the code that's triggering
the error messages is from vgacon_set_cursor_size().
After we re-enable the power well, every time we read/write the VGA
address 0x3d5 we get an "unclaimed register" interrupt (ERR_INT) and
print error messages. If we write anything to the VGA MSR register (it
doesn't really matter which value you write to bit 0), any
reads/writes to 0x3d5 _don't_ trigger the "unclaimed register" errors
anymore (even if MSR bit 0 is zero). So what happens with the current
code is that when we unbind i915 and bind vgacon, we call
console_unlock(). Function console_unlock() is responsible for
printing any messages that were supposed to be print when the console
was locked, so it calls the TTY layer, which calls the console layer,
which calls vgacon to print the messages. At this point, vgacon
eventually calls vgacon_set_cursor_size(), which touches 0x3d5, which
triggers unclaimed register interrupts. The problem is that when we
get these interrupts, we print the error messages, so we add more work
to console_unlock(), which will try to print it again, and then call
vgacon again, trigger a new interrupt, which will put more stuff to
the buffer, and then we'll be stuck at console_unlock() forever.
If you patch intel_uncore.c to not print anything when we detect
unclaimed registers, we won't get into the console_unlock() infinite
loop and the driver unbind will work just fine. We will still be
getting interrupts every time vgacon touches those registers, but we
will survive. This is a valid experiment, but IMHO it's not the real
fix: if we don't print any error messages we will still keep getting
the interrupts, and if we disable ERR_INT we won't get the interrupt
anymore, but we will also stop getting all the other error interrupts.
I talked about this problem with the HW engineer and his
recommendation is "So don't do any VGA I/O or memory access while the
power well is disabled, and make to re-program MSR after enabling the
power well and before using VGA I/O or memory accesses.".
Notice that this is just a partial fix to fd.o #67813. This fixes the
case where the power well is already enabled when we unbind, not when
it's disabled when we unbind.
V2: - Rebase (first version was sent in September).
V3: - Complete rewrite of the same fix: smaller implementation,
improved commit message.
Testcase: igt/drv_module_reload
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67813 Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Wed, 11 Dec 2013 20:50:08 +0000 (18:50 -0200)]
drm/i915: remove i915_disable_vga_mem declaration
It was supposed to have been killed on the same commit that killed the
function, e1264ebe9ff48e1b3e1dd11805eec9f5b143ab7c, but I guess the
intel_drv.h reorganization accidentally brought it back.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Shobhit Kumar [Tue, 10 Dec 2013 06:45:00 +0000 (12:15 +0530)]
drm/i915: Parametrize the dphy and other spec specific parameters
The values of these parameters will be different for differnet panel
based on dsi rate, lane count, etc. Remove the hardcodings and make
these as parameters whch will be initialized in panel specific
sub-encoder implementaion.
This will also form groundwork for planned generic panel sub-encoder
implemntation based on VBT design enhancments to support multiple panels
v2: Mask away the port_bits before use
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Shobhit Kumar [Wed, 11 Dec 2013 12:22:05 +0000 (17:52 +0530)]
drm/i915: Reorganize the DSI enable/disable sequence
Basically ULPS handling during enable/disable has been moved to
pre_enable and post_disable phases. PLL and panel power disable
also has been moved to post_disable phase. The ULPS entry/exit
sequneces as suggested by HW team is as follows -
During enable time -
set DEVICE_READY --> Clear DEVICE_READY --> set DEVICE_READY
And during disable time to flush all FIFOs -
set ENTER_SLEEP --> EXIT_SLEEP --> ENTER_SLEEP
Also during disbale sequnece sub-encoder disable is moved to the end
after port is disabled.
v2: Based on comments from Ville
- Detailed epxlaination in the commit messgae
- Moved parameter changes out into another patch
- Backlight enabling will be a new patch
v3: Updated as per Jani's comments
- Removed the I915_WRITE_BITS as it is not needed
- Moved panel_reset and send_otp_cmds hooks to dsi_pre_enable
- Moved disable_panel_power hook to dsi_post_disable
- Replace hardcoding with AFE_LATCHOUT
v4: Make intel_dsi_device_ready and intel_dsi_clear_device_ready static
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohan.marimuthu@intel.com> Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Shobhit Kumar [Tue, 10 Dec 2013 06:44:57 +0000 (12:14 +0530)]
drm/i915: Try harder to get best m, n, p values with minimal error
Basically check for both +ive and -ive deviation from target clock and
pick the one with minimal error. If we get a direct match, break from
loop to acheive some optimization.
v2: Use signed variable for target and calculated dsi clock values
Signed-off-by: Vijayakumar Balakrishnan <vijayakumar.balakrishnan@intel.com> Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Shobhit Kumar [Tue, 10 Dec 2013 06:44:56 +0000 (12:14 +0530)]
drm/i915: Compute dsi_clk from pixel clock
Pixel clock based calculation is recommended in the MIPI host controller
documentation
v2: Based on review comments from Jani and Ville
- Use dsi_clk in KHz rather than converting in Hz and back to MHz
- RR formula is retained though not used but return dsi_clk in KHz now
- Moved the m-n-p changes into a separate patch
- Removed the parameter check for intel_dsi->dsi_clock_freq. This will be
bought back in if needed when appropriate panel drivers are done
v3: Removed the unused mnp calculation from static table
Signed-off-by: Vijayakumar Balakrishnan <vijayakumar.balakrishnan@intel.com> Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 9 Dec 2013 16:54:17 +0000 (18:54 +0200)]
drm/i915: Decrease gen2 vco frequency minimum to 908 MHz
On my 855 machine the BIOS uses the following DPLL settings:
DPLL 0x90016000
FP0 = 0x61207
FP1 = 0x21207
With the 66MHz SSC refclock, that puts the BIOS generated VCO
frequency at ~908 MHz, which is lower than the 930 MHz limit
we have currently. This also results in the pixel clock coming
out significantly higher than the requested 65 MHz when we try
to recompute it.
Reduce the the VCO limit to 908 MHz. Combined with the earlier
SSC reference clock accuracy fix, this results in the pixel clock
coming out as 65.08 MHz which is quite close to the target. For
some reason the BIOS uses 64.881 MHz, which isn't quite as close.
This makes kms_flip wf_vblank-ts-check pass for the first time
on this machine \o/
Cc: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 9 Dec 2013 16:54:16 +0000 (18:54 +0200)]
drm/i915: Fix 66 MHz LVDS SSC freq for gen2
Store the SSC refclock frequency in kHz to get more accuracy. Currently
we're pretending that 66 MHz is ~66000 kHz, when in fact it is actually
~66667 kHz. By storing the less rounded kHz value we get a much better
accuracy for out pixel clock calculations.
Cc: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 9 Dec 2013 16:54:15 +0000 (18:54 +0200)]
drm/i915: Increase gen2 vco frequency limit to 1512 MHz
Bruno Prémont has a 855 machine with a 1400x1050 LVDS screen.
The VBT mode is as follows:
0:"1400x1050" 0 108000 1400 1416 1528 1688 1050 1051 1054 1066 0x8 0xa
The BIOS uses the following DPLL settings:
DPLL = 0x90020000
FP0 = 0x2140e
FP1 = 0x21207
That puts the BIOS generated VCO frequency at 1512 MHz, which is
higher than the 1400 MHz limit we have currently.
Let's bump the VCO limit to 1512 MHz and see what happens.
Cc: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 9 Dec 2013 16:54:14 +0000 (18:54 +0200)]
drm/i915: Change N divider minimum from 3 to 2 for gen2
Bruno Prémont has a 855 machine with a 1400x1050 LVDS screen.
The VBT mode is as follows:
0:"1400x1050" 0 108000 1400 1416 1528 1688 1050 1051 1054 1066 0x8 0xa
The BIOS uses the following DPLL settings:
DPLL = 0x90020000
FP0 = 0x2140e
FP1 = 0x21207
We can't generate that pixel clock currently as we're limiting the N
divider to at least 3, whereas the BIOS uses a value of 2.
Let's reduce the N minimum to 2 and see what happens.
Cc: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 9 Dec 2013 16:54:13 +0000 (18:54 +0200)]
drm/i915: Extract p2 divider correctly for gen2 LVDS dual channel
In order to determine the correct p2 divider for LVDS on gen2,
we need to check the CLKB mode from the LVDS port register to
determine if we're dealing with single or dual channel LVDS.
Cc: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 10 Dec 2013 19:44:43 +0000 (21:44 +0200)]
drm/i915: Record BB_ADDR for every ring
Every ring seems to have a BB_ADDR registers, so include them all in the
error state.
v2: Also include the _UDW on BDW
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 10 Dec 2013 18:47:44 +0000 (20:47 +0200)]
drm/i915: Use 32bit read for BB_ADDR
The BB_ADDR register is documented to be 32bits at least since SNB.
Prior to that the high 32bits were listed as MBZ, so using a 64bit read
doesn't seem worth anything. Also the simulator doesn't like the 64bit
read. So just switch to using a 32bit read instead.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 6 Dec 2013 19:32:42 +0000 (17:32 -0200)]
drm/i915: fix VDD override off wait
If we're disabling the VDD override bit and the panel is enabled, we
don't need to wait for anything. If the panel is disabled, then we
need to actually wait for panel_power_cycle_delay, not
panel_power_down_delay, because the power down delay was already
respected when we disabled the panel.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 6 Dec 2013 19:32:41 +0000 (17:32 -0200)]
drm/i915: don't touch the VDD when disabling the panel
I don't see a reason to touch VDD when we're disabling the panel:
since the panel is enabled, we don't need VDD. This saves a few sleep
calls from the vdd_on and vdd_off functions at every modeset.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69693 Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix the patch mangle wiggle has done ... Spotted by Paulo.
Also drop the runtime_pm_put call which now has to go due to different
patch ordering. Also from Paul.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 21 Nov 2013 15:47:28 +0000 (13:47 -0200)]
drm/i915: add runtime PM support on Haswell
The code to enable/disable PC8 already takes care of saving and
restoring all the registers we need to save/restore, so do a put()
call when we enable PC8 and a get() call when we disable it.
Ideally, in order to make it easier to add runtime PM support to other
platforms, we should move some things from the PC8 code to the runtime
PM code, but let's do this later, since we can make Haswell work right
now.
V2: - Rebase
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Don't actually enable runtime pm since I didn't merge all
patches.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 21 Nov 2013 15:47:25 +0000 (13:47 -0200)]
drm/i915: disable interrupts when enabling PC8
The plan is to merge PC8 and D3 into a single feature, and when we're
in D3 we won't get any hotplug interrupt anyway, so leaving them
enable doesn't make sense, and it also brings us a problem. The
problem is that we get a hotplug interrupt right when we we wake up
from D3, when we're still waking up everything. If we fully disable
interrupts we won't get this hotplug interrupt, so we won't have
problems.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 21 Nov 2013 15:47:24 +0000 (13:47 -0200)]
drm/i915: do not assert DE_PCH_EVENT_IVB enabled
The current code was checking if all bits of "val" were enabled and
DE_PCH_EVENT_IVB was disabled. The new code doesn't care about the
state of DE_PCH_EVENT_IVB: it just checks if everything else is 1.
The goal is that future patches may completely disable interrupts, and
the LCPLL-disabling code shouldn't care about the state of
DE_PCH_EVENT_IVB.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: I think the commit message is actually wrong in it's
description of what the old test checked, but the new one seems sane.
So meh.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 21 Nov 2013 15:47:23 +0000 (13:47 -0200)]
drm/i915: get a runtime PM reference when the panel VDD is on
And put it when it's off. Otherwise, when you run pm_pc8 from
intel-gpu-tools, and the delayed function that disables VDD runs,
we'll get some messages saying we're touching registers while the HW
is suspended.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Wed, 27 Nov 2013 20:20:34 +0000 (18:20 -0200)]
drm/i915: add runtime put/get calls at the basic places
If I add code to enable runtime PM on my Haswell machine, start a
desktop environment, then enable runtime PM, these functions will
complain that they're trying to read/write registers while the
graphics card is suspended.
v2: - Simplify i915_gem_fault changes.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Drop the hunk in i915_hangcheck_elapsed, it's the wrong thing
to do.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 6 Dec 2013 22:34:21 +0000 (20:34 -0200)]
drm/i915: do adapter power state notification at runtime PM
Now that we are actually setting the device to the D3 state, we should
issue the notification.
The opregion spec says we should send the message before the adapter
is about to be placed in a lower power state, and after the adapter is
placed in a higher power state.
Jani originally wrote a similar patch for PC8, but then we discovered
that we were not really changing the PCI D states when
enabling/disabling PC8, so we had to postpone his patch.
v2: - Improve commit message, explaining the expected state.
v3: - Rebase.
Cc: Jani Nikula <jani.nikula@intel.com> Credits-to: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> (v2) Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 6 Dec 2013 22:32:13 +0000 (20:32 -0200)]
drm/i915: add initial Runtime PM functions
This patch adds the initial infrastructure to allow a Runtime PM
implementation that sets the device to its D3 state. The patch just
adds the necessary callbacks and the initial infrastructure.
We still don't have any platform that actually uses this
infrastructure, we still don't call get/put in all the places we need
to, and we don't have any function to save/restore the state of the
registers. This is not a problem since no platform uses the code added
by this patch. We have a few people simultaneously working on runtime
PM, so this initial code could help everybody make their plans.
V2: - Move some functions to intel_pm.c
- Remove useless pm_runtime_allow() call at init
- Remove useless pm_runtime_mark_last_busy() call at get
- Use pm_runtime_get_sync() instead of 2 calls
- Add a WARN to check if we're really awake
V3: - Rebase.
V4: - Don't need to call pci_{save,restore}_state and
pci_set_power_sate, since they're already called by the PCI
layer
- Remove wrong pm_runtime_enable() call at init_runtime_pm
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Wed, 27 Nov 2013 19:59:22 +0000 (17:59 -0200)]
drm/i915: get a PC8 reference when enabling the power well
In the current code, at haswell_modeset_global_resources, first we
decide if we want to enable/disable the power well, then we decide if
we want to enable/disable PC8. On the case where we're enabling PC8
this works fine, but on the case where we disable PC8 due to a non-eDP
monitor being enabled, we first enable the power well and then disable
PC8. Although wrong, this doesn't seem to be causing any problems now,
and we don't even see anything in dmesg. But the patches for runtime
D3 turn this problem into a real bug, so we need to fix it.
This fixes the "modeset-non-lpsp" subtest from the "pm_pc8" test from
intel-gpu-tools.
v2: - Rebase (i915_disable_power_well).
v3: - More reabase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
projects / mirror_ubuntu-kernels.git / log