Dan Carpenter [Tue, 15 Dec 2015 10:07:52 +0000 (13:07 +0300)]
mISDN: fix a loop count
There are two issue here.
1) cnt starts as maxloop + 1 so all these loops iterate one more time
than intended.
2) At the end of the loop we test for "if (maxloop && !cnt)" but for
the first two loops, we end with cnt equal to -1. Changing this to
a pre-op means we end with cnt set to 0.
Fixes: cae86d4a4e56 ('mISDN: Add driver for Infineon ISDN chipset family') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: fc48866f7 ('net/mlx4: Adapt code for N-Port VF') Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Acked-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Mon, 14 Dec 2015 22:44:10 +0000 (17:44 -0500)]
skbuff: Fix offset error in skb_reorder_vlan_header
skb_reorder_vlan_header is called after the vlan header has
been pulled. As a result the offset of the begining of
the mac header has been incrased by 4 bytes (VLAN_HLEN).
When moving the mac addresses, include this incrase in
the offset calcualation so that the mac addresses are
copied correctly.
Fixes: a6e18ff1117 (vlan: Fix untag operations of stacked vlans with REORDER_HEADER off) CC: Nicolas Dichtel <nicolas.dichtel@6wind.com> CC: Patrick McHardy <kaber@trash.net> Signed-off-by: Vladislav Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Mon, 14 Dec 2015 21:48:36 +0000 (13:48 -0800)]
pptp: verify sockaddr_len in pptp_bind() and pptp_connect()
Reported-by: Dmitry Vyukov <dvyukov@gmail.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kazuya Mizuguchi [Sun, 13 Dec 2015 15:15:58 +0000 (00:15 +0900)]
ravb: Add disable 10base
Ethernet AVB does not support 10 Mbps transfer speed.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sun, 13 Dec 2015 20:05:07 +0000 (23:05 +0300)]
sh_eth: fix descriptor access endianness
The driver never calls cpu_to_edmac() when writing the descriptor address
and edmac_to_cpu() when reading it, although it should -- fix this.
Note that the frame/buffer length descriptor field accesses also need fixing
but since they are both 16-bit we can't use {cpu|edmac}_to_{edmac|cpu}()...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sun, 13 Dec 2015 18:27:04 +0000 (21:27 +0300)]
sh_eth: fix TX buffer byte-swapping
For the little-endian SH771x kernels the driver has to byte-swap the RX/TX
buffers, however yet unset physcial address from the TX descriptor is used
to call sh_eth_soft_swap(). Use 'skb->data' instead...
Fixes: 31fcb99d9958 ("net: sh_eth: remove __flush_purge_region") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 14 Dec 2015 22:08:53 +0000 (14:08 -0800)]
net: fix IP early demux races
David Wilder reported crashes caused by dst reuse.
<quote David>
I am seeing a crash on a distro V4.2.3 kernel caused by a double
release of a dst_entry. In ipv4_dst_destroy() the call to
list_empty() finds a poisoned next pointer, indicating the dst_entry
has already been removed from the list and freed. The crash occurs
18 to 24 hours into a run of a network stress exerciser.
</quote>
Thanks to his detailed report and analysis, we were able to understand
the core issue.
IP early demux can associate a dst to skb, after a lookup in TCP/UDP
sockets.
When socket cache is not properly set, we want to store into
sk->sk_dst_cache the dst for future IP early demux lookups,
by acquiring a stable refcount on the dst.
Problem is this acquisition is simply using an atomic_inc(),
which works well, unless the dst was queued for destruction from
dst_release() noticing dst refcount went to zero, if DST_NOCACHE
was set on dst.
We need to make sure current refcount is not zero before incrementing
it, or risk double free as David reported.
This patch, being a stable candidate, adds two new helpers, and use
them only from IP early demux problematic paths.
It might be possible to merge in net-next skb_dst_force() and
skb_dst_force_safe(), but I prefer having the smallest patch for stable
kernels : Maybe some skb_dst_force() callers do not expect skb->dst
can suddenly be cleared.
Can probably be backported back to linux-3.6 kernels
Reported-by: David J. Wilder <dwilder@us.ibm.com> Tested-by: David J. Wilder <dwilder@us.ibm.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sat, 12 Dec 2015 22:44:50 +0000 (01:44 +0300)]
sh_eth: uninline sh_eth_{write|read}()
Commit 3365711df024 ("sh_eth: WARN on access to a register not implemented in
in a particular chip") added WARN_ON() to sh_eth_{read|write}(), thus making
it unacceptable for these functions to be *inline* anymore. Remove *inline*
and move the functions from the header to the driver itself. Below is our
code economy with ARM gcc 4.7.3:
$ size drivers/net/ethernet/renesas/sh_eth.o{~,}
text data bss dec hex filename
32489 1140 0 33629 835d drivers/net/ethernet/renesas/sh_eth.o~
25413 1140 0 26553 67b9 drivers/net/ethernet/renesas/sh_eth.o
Suggested-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chen-Yu Tsai [Fri, 11 Dec 2015 10:03:49 +0000 (18:03 +0800)]
stmmac: dwmac-sunxi: Call exit cleanup function in probe error path
dwmac-sunxi has 2 callbacks that were called from stmmac_platform as
part of the probe and remove sequences.
Ater the conversion of dwmac-sunxi into a standalone platform driver,
the .init function is called before calling into the stmmac driver
core, but .exit is not called to clean up if stmmac returns an error.
This patch fixes the probe error path. This properly cleans up and
releases resources when the driver core fails to probe.
Cc: Joachim Eastwood <manabian@gmail.com> Fixes: 9a9e9a1edee8 ("stmmac: dwmac-sunxi: turn setup callback into a
probe function") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: David S. Miller <davem@davemloft.net>
AF_INET, AF_INET6 sockets actually only support 8-bit protocol
identifiers. inet_sock's skc_protocol field thus is sized accordingly,
thus larger protocol identifiers simply cut off the higher bits and
store a zero in the protocol fields.
This could lead to e.g. NULL function pointer because as a result of
the cut off inet_num is zero and we call down to inet_autobind, which
is NULL for raw sockets.
I found no particular commit which introduced this problem.
CVE: CVE-2015-8543 Cc: Cong Wang <cwang@twopensource.com> Reported-by: 郭永刚 <guoyonggang@360.cn> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Mon, 14 Dec 2015 12:51:51 +0000 (13:51 +0100)]
net: phy: mdio-mux: Check return value of mdiobus_alloc()
mdiobus_alloc() might return NULL, but its return value is not
checked in mdio_mux_init(). This could potentially lead to a NULL
pointer dereference. Fix it by checking the return value
Fixes: 0ca2997d1452 ("netdev/of/phy: Add MDIO bus multiplexer support.") Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Mon, 14 Dec 2015 13:29:58 +0000 (14:29 +0100)]
openvswitch: fix trivial comment typo
The commit 33db4125ec74 ("openvswitch: Rename LABEL->LABELS") left
over an old OVS_CT_ATTR_LABEL instance, fix it.
Fixes: 33db4125ec74 ("openvswitch: Rename LABEL->LABELS") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Joe Stringer <joe@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
The following patchset contains Netfilter fixes for you net tree,
specifically for nf_tables and nfnetlink_queue, they are:
1) Avoid a compilation warning in nfnetlink_queue that was introduced
in the previous merge window with the simplification of the conntrack
integration, from Arnd Bergmann.
2) nfnetlink_queue is leaking the pernet subsystem registration from
a failure path, patch from Nikolay Borisov.
3) Pass down netns pointer to batch callback in nfnetlink, this is the
largest patch and it is not a bugfix but it is a dependency to
resolve a splat in the correct way.
4) Fix a splat due to incorrect socket memory accounting with nfnetlink
skbuff clones.
5) Add missing conntrack dependencies to NFT_DUP_IPV4 and NFT_DUP_IPV6.
6) Traverse the nftables commit list in reverse order from the commit
path, otherwise we crash when the user applies an incremental update
via 'nft -f' that deletes an object that was just introduced in this
batch, from Xin Long.
Regarding the compilation warning fix, many people have sent us (and
keep sending us) patches to address this, that's why I'm including this
batch even if this is not critical.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 10 Dec 2015 18:25:24 +0000 (10:25 -0800)]
net: Flush local routes when device changes vrf association
The VRF driver cycles netdevs when an interface is enslaved or released:
the down event is used to flush neighbor and route tables and the up
event (if the interface was already up) effectively moves local and
connected routes to the proper table.
As of 4f823defdd5b the local route is left hanging around after a link
down, so when a netdev is moved from one VRF to another (or released
from a VRF altogether) local routes are left in the wrong table.
Fix by handling the NETDEV_CHANGEUPPER event. When the upper dev is
an L3mdev then call fib_disable_ip to flush all routes, local ones
to.
Fixes: 4f823defdd5b ("ipv4: fix to not remove local route on link down") Cc: Julian Anastasov <ja@ssi.bg> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 7 Dec 2015 10:48:07 +0000 (18:48 +0800)]
netfilter: nf_tables: use reverse traversal commit_list in nf_tables_abort
When we use 'nft -f' to submit rules, it will build multiple rules into
one netlink skb to send to kernel, kernel will process them one by one.
meanwhile, it add the trans into commit_list to record every commit.
if one of them's return value is -EAGAIN, status |= NFNL_BATCH_REPLAY
will be marked. after all the process is done. it will roll back all the
commits.
now kernel use list_add_tail to add trans to commit, and use
list_for_each_entry_safe to roll back. which means the order of adding
and rollback is the same. that will cause some cases cannot work well,
even trigger call trace, like:
1. add a set into table foo [return -EAGAIN]:
commit_list = 'add set trans'
2. del foo:
commit_list = 'add set trans' -> 'del set trans' -> 'del tab trans'
then nf_tables_abort will be called to roll back:
firstly process 'add set trans':
case NFT_MSG_NEWSET:
trans->ctx.table->use--;
list_del_rcu(&nft_trans_set(trans)->list);
it will del the set from the table foo, but it has removed when del
table foo [step 2], then the kernel will panic.
the right order of rollback should be:
'del tab trans' -> 'del set trans' -> 'add set trans'.
which is opposite with commit_list order.
so fix it by rolling back commits with reverse order in nf_tables_abort.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
David S. Miller [Sat, 12 Dec 2015 05:43:44 +0000 (00:43 -0500)]
Merge branch 'mpls-fixes'
Robert Shearman says:
====================
mpls: fixes for nexthops without via addresses
These four fixes all apply to the case of having an mpls route with an
output device, but without a nexthop.
Patches 2 and 3 could really have been combined in one patch, but I
wanted to separate the fix for some recent breakage from the fix for a
day-1 issue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Thu, 10 Dec 2015 19:30:51 +0000 (19:30 +0000)]
mpls: make via address optional for multipath routes
The via address is optional for a single path route, yet is mandatory
when the multipath attribute is used:
# ip -f mpls route add 100 dev lo
# ip -f mpls route add 101 nexthop dev lo
RTNETLINK answers: Invalid argument
Make them consistent by making the via address optional when the
RTA_MULTIPATH attribute is being parsed so that both forms of
specifying the route work.
Signed-off-by: Robert Shearman <rshearma@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Thu, 10 Dec 2015 19:30:50 +0000 (19:30 +0000)]
mpls: fix out-of-bounds access when via address not specified
When a via address isn't specified, the via table is left initialised
to 0 (NEIGH_ARP_TABLE), and the via address length also left
initialised to 0. This results in a via address array of length 0
being allocated (contiguous with route and nexthop array), meaning
that when a packet is sent using neigh_xmit the neighbour lookup and
creation will cause an out-of-bounds access when accessing the 4 bytes
of the IPv4 address it assumes it has been given a pointer to.
This could be fixed by allocating the 4 bytes of via address necessary
and leaving it as all zeroes. However, it seems wrong to me to use an
ipv4 nexthop (including possibly ARPing for 0.0.0.0) when the user
didn't specify to do so.
Instead, set the via address table to NEIGH_NR_TABLES to signify it
hasn't been specified and use this at forwarding time to signify a
neigh_xmit using an L2 address consisting of the device address. This
mechanism is the same as that used for both ARP and ND for loopback
interfaces and those flagged as no-arp, which are all we can really
support in this case.
Fixes: cf4b24f0024f ("mpls: reduce memory usage of routes") Signed-off-by: Robert Shearman <rshearma@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Thu, 10 Dec 2015 19:30:49 +0000 (19:30 +0000)]
mpls: don't dump RTA_VIA attribute if not specified
The problem seen is that when adding a route with a nexthop with no
via address specified, iproute2 generates bogus output:
# ip -f mpls route add 100 dev lo
# ip -f mpls route list
100 via inet 0.0.8.0 dev lo
The reason for this is that the kernel generates an RTA_VIA attribute
with the family set to AF_INET, but the via address data having zero
length. The cause of family being AF_INET is that on route insert
cfg->rc_via_table is left set to 0, which just happens to be
NEIGH_ARP_TABLE which is then translated into AF_INET.
iproute2 doesn't validate the length prior to printing and so prints
garbage. Although it could be fixed to do the validation, I would
argue that AF_INET addresses should always be exactly 4 bytes so the
kernel is really giving userspace bogus data.
Therefore, avoid generating the RTA_VIA attribute when dumping the
route if the via address wasn't specified on add/modify. This is
indicated by NEIGH_ARP_TABLE and a zero via address length - if the
user specified a via address the address length would have been
validated such that it was 4 bytes. Although this is a change in
behaviour that is visible to userspace, I believe that what was
generated before was invalid and as such userspace wouldn't be
expecting it.
Signed-off-by: Robert Shearman <rshearma@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Thu, 10 Dec 2015 19:30:48 +0000 (19:30 +0000)]
mpls: validate L2 via address length
If an L2 via address for an mpls nexthop is specified, the length of
the L2 address must match that expected by the output device,
otherwise it could access memory beyond the end of the via address
buffer in the route.
This check was present prior to commit f8efb73c97e2 ("mpls: multipath
route support"), but got lost in the refactoring, so add it back,
applying it to all nexthops in multipath routes.
Fixes: f8efb73c97e2 ("mpls: multipath route support") Signed-off-by: Robert Shearman <rshearma@brocade.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bert Kenward [Fri, 11 Dec 2015 09:39:32 +0000 (09:39 +0000)]
sfc: only use RSS filters if we're using RSS
Without this, filter insertion on a VF would fail if only one channel
was in use. This would include the unicast station filter and therefore
no traffic would be received.
Signed-off-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The reset logic calls bnxt_close_nic() and bnxt_open_nic() under rtnl_lock
from bnxt_sp_task. BNXT_STATE_IN_SP_TASK must be cleared before calling
bnxt_close_nic() to avoid deadlock.
v2: Fixed white space error. Thanks Dave.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 10 Dec 2015 00:35:43 +0000 (19:35 -0500)]
bnxt_en: Don't cancel sp_task from bnxt_close_nic().
When implementing driver reset from tx_timeout in the next patch,
bnxt_close_nic() will be called from the sp_task workqueue. Calling
cancel_work() on sp_task will hang the workqueue.
Instead, set a new bit BNXT_STATE_IN_SP_TASK when bnxt_sp_task() is running.
bnxt_close_nic() will wait for BNXT_STATE_IN_SP_TASK to clear before
proceeding.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 10 Dec 2015 00:35:41 +0000 (19:35 -0500)]
bnxt_en: Fix bitmap declaration to work on 32-bit arches.
The declaration of the bitmap vf_req_snif_bmap using fixed array of
unsigned long will only work on 64-bit archs. Use DECLARE_BITMAP instead
which will work on all archs.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Stringer [Wed, 9 Dec 2015 22:07:40 +0000 (14:07 -0800)]
openvswitch: Respect conntrack zone even if invalid
If userspace executes ct(zone=1), and the connection tracker determines
that the packet is invalid, then the ct_zone flow key field is populated
with the default zone rather than the zone that was specified. Even
though connection tracking failed, this field should be updated with the
value that the action specified. Fix the issue.
Fixes: 7f8a436eaa2c ("openvswitch: Add conntrack action") Signed-off-by: Joe Stringer <joe@ovn.org> Acked-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Stringer [Wed, 9 Dec 2015 22:07:39 +0000 (14:07 -0800)]
openvswitch: Fix helper reference leak
If the actions (re)allocation fails, or the actions list is larger than the
maximum size, and the conntrack action is the last action when these
problems are hit, then references to helper modules may be leaked. Fix
the issue.
Fixes: cae3a2627520 ("openvswitch: Allow attaching helpers to ct action") Signed-off-by: Joe Stringer <joe@ovn.org> Acked-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Wed, 9 Dec 2015 18:56:31 +0000 (19:56 +0100)]
phy: micrel: Fix finding PHY properties in MAC node.
commit 8b63ec1837fa ("phylib: Make PHYs children of their MDIO bus,
not the bus' parent.") changed the parenting of PHY devices, making
them a child of the MDIO bus, instead of the MAC device. This broken
the Micrel PHY driver which has a deprecated feature of allowing PHY
properties to be placed into the MAC node.
In order to find the MAC node, we need to walk up the tree of devices
until we find one with an OF node attached.
Reported-by: Dinh Nguyen <dinguyen@opensource.altera.com> Suggested-by: David Daney <david.daney@cavium.com> Acked-by: David Daney <david.daney@cavium.com> Fixes: 8b63ec1837fa ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 9 Dec 2015 15:25:06 +0000 (07:25 -0800)]
ipv6: sctp: clone options to avoid use after free
SCTP is lacking proper np->opt cloning at accept() time.
TCP and DCCP use ipv6_dup_options() helper, do the same
in SCTP.
We might later factorize this code in a common helper to avoid
future mistakes.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 8 Dec 2015 15:22:02 +0000 (07:22 -0800)]
xfrm: add rcu protection to sk->sk_policy[]
XFRM can deal with SYNACK messages, sent while listener socket
is not locked. We add proper rcu protection to __xfrm_sk_clone_policy()
and xfrm_sk_policy_lookup()
This might serve as the first step to remove xfrm.xfrm_policy_lock
use in fast path.
Fixes: fa76ce7328b2 ("inet: get rid of central tcp/dccp listener timer") Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 8 Dec 2015 15:22:01 +0000 (07:22 -0800)]
xfrm: add rcu grace period in xfrm_policy_destroy()
We will soon switch sk->sk_policy[] to RCU protection,
as SYNACK packets are sent while listener socket is not locked.
This patch simply adds RCU grace period before struct xfrm_policy
freeing, and the corresponding rcu_head in struct xfrm_policy.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: nfnetlink: fix splat due to incorrect socket memory accounting in skbuff clones
If we attach the sk to the skb from nfnetlink_rcv_batch(), then
netlink_skb_destructor() will underflow the socket receive memory
counter and we get warning splat when releasing the socket.
$ cat /proc/net/netlink
sk Eth Pid Groups Rmem Wmem Dump Locks Drops Inode ffff8800ca903000 12 0 00000000 -54144 0 0 2 0 17942
^^^^^^
skb->sk was only needed to lookup for the netns, however we don't need
this anymore since 633c9a840d0b ("netfilter: nfnetlink: avoid recurrent
netns lookups in call_batch") so this patch removes this manual socket
assignment to resolve this problem.
Reported-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com> Reported-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Tested-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Nikolay Borisov [Mon, 7 Dec 2015 10:13:26 +0000 (12:13 +0200)]
netfilter: nfnetlink_queue: Unregister pernet subsys in case of init failure
Commit 3bfe049807c2403 ("netfilter: nfnetlink_{log,queue}:
Register pernet in first place") reorganised the initialisation
order of the pernet_subsys to avoid "use-before-initialised"
condition. However, in doing so the cleanup logic in nfnetlink_queue
got botched in that the pernet_subsys wasn't cleaned in case
nfnetlink_subsys_register failed. This patch adds the necessary
cleanup routine call.
Fixes: 3bfe049807c2403 ("netfilter: nfnetlink_{log,queue}: Register pernet in first place") Signed-off-by: Nikolay Borisov <kernel@kyup.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Arnd Bergmann [Tue, 8 Dec 2015 15:28:59 +0000 (16:28 +0100)]
net: ezchip: fix address space confusion in nps_enet.c
The nps_enet driver happily mixes virtual, physical and __iomem
addresses, which are all different depending on the architecture
and configuration. That causes a warning when building the code
on ARM with LPAE mode enabled:
drivers/net/ethernet/ezchip/nps_enet.c: In function 'nps_enet_send_frame':
drivers/net/ethernet/ezchip/nps_enet.c:370:13: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
but will also fail to work for other reasons.
In this patch, I'm trying to change the code to use only normal
kernel pointers, which I assume is what the author actually meant:
* For reading or writing a 32-bit word that may be unaligned when
an SKB contains unaligned data, I'm using get_unaligned/put_unaligned()
rather than memcpy_fromio/toio.
* For converting a u8 pointer to a u32 pointer, I use a cast rather
than the incorrect virt_to_phys.
* For copying a couple of bytes from one place to another while respecting
alignment, I use memcpy instead of memcpy_toio.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Tue, 8 Dec 2015 15:17:29 +0000 (16:17 +0100)]
net: fsl: avoid 64-bit warning on pq_mdio
The pq_mdio driver can now be built for ARM64, where we get a format
string warning:
drivers/net/ethernet/freescale/fsl_pq_mdio.c: In function 'fsl_pq_mdio_probe':
drivers/net/ethernet/freescale/fsl_pq_mdio.c:467:25: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'long int' [-Wformat=]
The argument is an implicit ptrdiff_t from the subtraction of two pointers,
so we should use the %z format string modifier to make this work on 64-bit
architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: fe761bcb9046 ("net: fsl: expands dependencies of NET_VENDOR_FREESCALE") Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Wu [Tue, 8 Dec 2015 11:17:42 +0000 (12:17 +0100)]
r8152: fix lockup when runtime PM is enabled
When an interface is brought up which was previously suspended (via
runtime PM), it would hang. This happens because napi_disable is called
before napi_enable.
Solve this by avoiding napi_enable in the resume during open function
(netif_running is true when open is called, IFF_UP is set after a
successful open; netif_running is false when close is called, but IFF_UP
is then still set).
While at it, remove WORK_ENABLE check from rtl8152_open (introduced with
the original change) because it cannot happen:
- After this patch, runtime resume will not set it during rtl8152_open.
- When link is up, rtl8152_open is not called.
- When link is down during system/auto suspend/resume, it is not set.
Fixes: 41cec84cf285 ("r8152: don't enable napi before rx ready") Link: https://lkml.kernel.org/r/20151205105912.GA1766@al Signed-off-by: Peter Wu <peter@lekensteyn.nl> Acked-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Fedin [Tue, 8 Dec 2015 07:37:44 +0000 (10:37 +0300)]
net: thunderx: Correctly distinguish between VF and LMAC count
Commit bc69fdfc6c13
("net: thunderx: Enable BGX LMAC's RX/TX only after VF is up")
introduces lmac_cnt member and starts verifying VF number against it.
This is plain wrong, and works only because currently we have hardcoded
1:1 mapping between VFs and LMACs, and in this case num_vf_en and
lmac_cnt are always equal. However in future this may change, and the
code will badly misbehave. The worst consequence of this is failure to
deliver link status messages, causing VFs to go defunct because since
commit 0b72a9a1060e ("net: thunderx: Switchon carrier only upon
interface link up") VF will not fully bring itself up without it.
This patch fixes the potential problem by doing VF number checks against
the num_vf_en. Since lmac_cnt is not used anywhere else, it is removed.
Additionally some duplicated code is factored out into nic_enable_vf()
Signed-off-by: Pavel Fedin <p.fedin@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar [Tue, 8 Dec 2015 03:17:30 +0000 (19:17 -0800)]
geneve: Fix IPv6 xmit stats update.
Call to iptunnel_xmit_stats() is not required after udp-tunnel6-xmit.
By calling iptunnel_xmit_stats() results in incorrect device stats.
Following patch drops this call.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 7 Dec 2015 16:53:17 +0000 (08:53 -0800)]
xfrm: take care of request sockets
TCP SYNACK messages might now be attached to request sockets.
XFRM needs to get back to a listener socket.
Adds new helpers that might be used elsewhere :
sk_to_full_sk() and sk_const_to_full_sk()
Note: We also need to add RCU protection for xfrm lookups,
now TCP/DCCP have lockless listener processing. This will
be addressed in separate patches.
Fixes: ca6fb0651883 ("tcp: attach SYNACK messages to request sockets instead of listener") Reported-by: Dave Jones <davej@codemonkey.org.uk> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 7 Dec 2015 16:25:21 +0000 (08:25 -0800)]
ipv6: sctp: fix lockdep splat in sctp_v6_get_dst()
While cooking the sctp np->opt rcu fixes, I forgot to move
one rcu_read_unlock() after the added rcu_dereference() in
sctp_v6_get_dst()
This gave lockdep warnings reported by Dave Jones.
Fixes: c836a8ba9386 ("ipv6: sctp: add rcu protection around np->opt") Reported-by: Dave Jones <davej@codemonkey.org.uk> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc [Mon, 7 Dec 2015 15:29:08 +0000 (16:29 +0100)]
vxlan: interpret IP headers for ECN correctly
When looking for outer IP header, use the actual socket address family, not
the address family of the default destination which is not set for metadata
based interfaces (and doesn't have to match the address family of the
received packet even if it was set).
Fix also the misleading comment.
Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 7 Dec 2015 21:59:19 +0000 (16:59 -0500)]
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
Included changes:
- prevent compatibility issue between DAT and speedy join from creating
inconsistencies in the global translation table
- make sure temporary TT entries are purged out if not claimed
- fix comparison function used for TT hash table
- fix invalid stack access in batadv_dat_select_candidates()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Mon, 7 Dec 2015 12:53:15 +0000 (12:53 +0000)]
mpls: fix sending of local encapped packets
Locally generated IPv4 and (probably) IPv6 packets are dropped because
skb->protocol isn't set. We could write wrappers to lwtunnel_output
for IPv4 and IPv6 that set the protocol accordingly and then call
lwtunnel_output, but mpls_output relies on the AF-specific type of dst
anyway to get the via address.
Therefore, make use of dst->dst_ops->family in mpls_output to
determine the type of nexthop and thus protocol of the packet instead
of checking skb->protocol.
Fixes: 61adedf3e3f1 ("route: move lwtunnel state to dst_entry") Reported-by: Sam Russell <sam.h.russell@gmail.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 7 Dec 2015 21:31:25 +0000 (16:31 -0500)]
Merge branch 'vxlan-ipv6-metadata-dst'
Jiri Benc says:
====================
vxlan: IPv6 fill_metadata_dst support
This adds IPv6 support to ndo_fill_metadata_dst in vxlan. The IPv4 part
needs some restructuring to avoid duplicate code, this will be sent as
a separate patch targeting net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc [Mon, 7 Dec 2015 12:04:31 +0000 (13:04 +0100)]
vxlan: support ndo_fill_metadata_dst also for IPv6
Fill the metadata correctly even when tunneling over IPv6. Also, check that
the provided metadata is of an address family that is supported by the
tunnel.
Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When using INTa, ISR might be called before device is configured
for INTa [E.g., due to other device asserting the shared interrupt line],
in which case the ISR would read the SISR registers that shouldn't be
read unless HW is already configured for INTa. This might break interrupts
later on. There's also an MSI-X issue due to this difference, although
it's mostly theoretical.
This patch changes the initialization order, calling request_irq() for the
slowpath interrupt only after the chip is configured for working
in the preferred interrupt mode.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com> Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ariel Elior [Mon, 7 Dec 2015 11:25:58 +0000 (06:25 -0500)]
qed: Fix BAR size split for some servers
Can't rely on pci config space to discover bar size,
as in some environments this returns a wrong, too large value.
Instead, rely on device register, which contains the value
provided by MFW at preboot.
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tomer Tayar [Mon, 7 Dec 2015 11:25:57 +0000 (06:25 -0500)]
qed: fix handling of concurrent ramrods.
Concurrent non-blocking slowpath ramrods can be completed
out-of-order on the completion chain. Recycling completed elements,
while previously sent elements are still completion pending,
can lead to overriding of active elements on the chain. Furthermore,
sending pending slowpath ramrods currently lacks the update of the
chain element physical pointer.
This patch:
* Ensures that ramrods are sent to the FW with
consecutive echo values.
* Handles out-of-order completions by freeing only first
successive completed entries.
* Updates the chain element physical pointer when copying
a pending element into a free element for sending.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com> Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tomer Tayar [Mon, 7 Dec 2015 11:25:56 +0000 (06:25 -0500)]
qed: Fix corner case for chain in-between pages
The amount of chain next pointer elements between the producer
and the consumer indices depends on which pages they currently
point to. The current calculation is based only on their difference,
and it can lead to a number of free elements which is higher by 1
than the actual value.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com> Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sven Eckelmann [Tue, 3 Nov 2015 09:05:44 +0000 (10:05 +0100)]
batman-adv: Fix invalid stack access in batadv_dat_select_candidates
batadv_dat_select_candidates provides an u32 to batadv_hash_dat but it
needs a batadv_dat_entry with at least ip and vid filled in.
Fixes: 3e26722bc9f2 ("batman-adv: make the Distributed ARP Table vlan aware") Signed-off-by: Sven Eckelmann <sven@open-mesh.com> Acked-by: Antonio Quartulli <antonio@meshcoding.com> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The translation table implementation, namely batadv_compare_tt(),
is used to compare two client entries and deciding if they are the
holding the same information. Each client entry is identified by
its mac address and its VLAN id (VID).
Consequently, batadv_compare_tt() has to not only compare the mac
addresses but also the VIDs.
Without this fix adding a new client entry that possesses the same
mac address as another client but operates on a different VID will
fail because both client entries will considered identical.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
In the case when a temporary entry is added first and a proper tt entry
is added after that, the temporary tt entry is kept in the orig list.
However the temporary flag is removed at this point, and therefore the
purge function can not find this temporary entry anymore.
Therefore, remove the previous temp entry before adding the new proper
one.
This case can happen if a client behind a given originator moves before
the TT announcement is sent out. Other than that, this case can also be
created by bogus or malicious payload frames for VLANs which are not
existent on the sending originator.
Reported-by: Alessandro Bolletta <alessandro@mediaspot.net> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Acked-by: Antonio Quartulli <antonio@meshcoding.com> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
DAT Cache replies are answered on behalf of other clients which are not
connected to the answering originator. Therefore, we shouldn't add these
clients to the answering originators TT table through speed join to
avoid bogus entries.
Reported-by: Alessandro Bolletta <alessandro@mediaspot.net> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Acked-by: Antonio Quartulli <antonio@meshcoding.com> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Felix Fietkau [Sat, 5 Dec 2015 12:58:11 +0000 (13:58 +0100)]
net: remove unnecessary semicolon in netdev_alloc_pcpu_stats()
This semicolon causes a build error if the function call is wrapped in
parentheses.
Fixes: aabc92bbe3cf ("net: add __netdev_alloc_pcpu_stats() to indicate gfp flags") Reported-by: Imre Kaloz <kaloz@openwrt.org> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
lucien [Sat, 5 Dec 2015 07:35:36 +0000 (15:35 +0800)]
sctp: start t5 timer only when peer rwnd is 0 and local state is SHUTDOWN_PENDING
when A sends a data to B, then A close() and enter into SHUTDOWN_PENDING
state, if B neither claim his rwnd is 0 nor send SACK for this data, A
will keep retransmitting this data until t5 timeout, Max.Retrans times
can't work anymore, which is bad.
if B's rwnd is not 0, it should send abort after Max.Retrans times, only
when B's rwnd == 0 and A's retransmitting beyonds Max.Retrans times, A
will start t5 timer, which is also commit f8d960524328 ("sctp: Enforce
retransmission limit during shutdown") means, but it lacks the condition
peer rwnd == 0.
so fix it by adding a bit (zero_window_announced) in peer to record if
the last rwnd is 0. If it was, zero_window_announced will be set. and use
this bit to decide if start t5 timer when local.state is SHUTDOWN_PENDING.
Fixes: commit f8d960524328 ("sctp: Enforce retransmission limit during shutdown") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
lucien [Sat, 5 Dec 2015 07:19:27 +0000 (15:19 +0800)]
sctp: only drop the reference on the datamsg after sending a msg
If the chunks are enqueued successfully but sctp_cmd_interpreter()
return err to sctp_sendmsg() (mainly because of no mem), the chunks will
get re-queued, but we are dropping the reference and freeing them.
The fix is to just drop the reference on the datamsg just as it had
succeeded, as:
- if the chunks weren't queued, this is enough to get them freed.
- if they were queued, they will get freed when they finally get out or
discarded.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
lucien [Sat, 5 Dec 2015 07:15:17 +0000 (15:15 +0800)]
sctp: hold the chunks only after the chunk is enqueued in outq
When a msg is sent, sctp will hold the chunks of this msg and then try
to enqueue them. But if the chunks are not enqueued in sctp_outq_tail()
because of the invalid state, sctp_cmd_interpreter() may still return
success to sctp_sendmsg() after calling sctp_outq_flush(), these chunks
will become orphans and will leak.
So we fix them by moving sctp_chunk_hold() to sctp_outq_tail(), where we
are sure that the chunk is going to get queued.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Wahren [Fri, 4 Dec 2015 15:29:10 +0000 (16:29 +0100)]
net: qca_spi: fix transmit queue timeout handling
In case of a tx queue timeout every transmit is blocked until the
QCA7000 resets himself and triggers a sync which makes the driver
flushs the tx ring. So avoid this blocking situation by triggering
the sync immediately after the timeout. Waking the queue doesn't
make sense in this situation.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000") Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Sat, 5 Dec 2015 12:01:50 +0000 (13:01 +0100)]
net: cdc_mbim: add "NDP to end" quirk for Huawei E3372
The Huawei E3372 (12d1:157d) needs this quirk in MBIM mode
as well. Allow this by forcing the NTB to contain only a
single NDP, and add a device specific entry for this ID.
Due to the way Huawei use device IDs, this might be applied
to other modems as well. It is assumed that those modems
will be based on the same firmware and will need this quirk
too. If not, it will still not harm normal usage, although
multiplexing performance could be impacted.
Cc: Enrico Mioso <mrkiko.rs@gmail.com> Reported-by: Sami Farin <hvtaifwkbgefbaei@gmail.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Acked-By: Enrico Mioso <mrkiko.rs@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vmalloc cannot be used in BH disabled contexts, even
with GFP_ATOMIC. And we certainly want to support
rhashtable users inserting entries with software
interrupts disabled.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 6 Dec 2015 03:23:23 +0000 (22:23 -0500)]
Merge branch 'sctp-timestamp-fixes'
Marcelo Ricardo Leitner says:
====================
sctp: packet timestamp fixes
These a couple of fixes regarding sctp/packet timestamps.
Dmitry Vyukov <dvyukov@google.com> reported the counter leak on missing
net_enable_timestamp() (2nd patch) and further testing here revealed the
other two issues.
Please consider these to -stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp: also copy sk_tsflags when copying the socket
As we are keeping timestamps on when copying the socket, we also have to
copy sk_tsflags.
This is needed since b9f40e21ef42 ("net-timestamp: move timestamp flags
out of sk_flags").
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sctp: update the netstamp_needed counter when copying sockets
Dmitry Vyukov reported that SCTP was triggering a WARN on socket destroy
related to disabling sock timestamp.
When SCTP accepts an association or peel one off, it copies sock flags
but forgot to call net_enable_timestamp() if a packet timestamping flag
was copied, leading to extra calls to net_disable_timestamp() whenever
such clones were closed.
The fix is to call net_enable_timestamp() whenever we copy a sock with
that flag on, like tcp does.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sctp: use the same clock as if sock source timestamps were on
SCTP echoes a cookie o INIT ACK chunks that contains a timestamp, for
detecting stale cookies. This cookie is echoed back to the server by the
client and then that timestamp is checked.
Thing is, if the listening socket is using packet timestamping, the
cookie is encoded with ktime_get() value and checked against
ktime_get_real(), as done by __net_timestamp().
The fix is to sctp also use ktime_get_real(), so we can compare bananas
with bananas later no matter if packet timestamping was enabled or not.
Fixes: 52db882f3fc2 ("net: sctp: migrate cookie life from timeval to ktime") Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc [Fri, 4 Dec 2015 12:54:03 +0000 (13:54 +0100)]
vxlan: fix incorrect RCO bit in VXLAN header
Commit 3511494ce2f3d ("vxlan: Group Policy extension") changed definition of
VXLAN_HF_RCO from 0x00200000 to BIT(24). This is obviously incorrect. It's
also in violation with the RFC draft.
Fixes: 3511494ce2f3d ("vxlan: Group Policy extension") Cc: Thomas Graf <tgraf@suug.ch> Cc: Tom Herbert <therbert@google.com> Signed-off-by: Jiri Benc <jbenc@redhat.com> Acked-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Fri, 4 Dec 2015 13:15:08 +0000 (14:15 +0100)]
ipv6: keep existing flags when setting IFA_F_OPTIMISTIC
Commit 64236f3f3d74 ("ipv6: introduce IFA_F_STABLE_PRIVACY flag")
failed to update the setting of the IFA_F_OPTIMISTIC flag, causing
the IFA_F_STABLE_PRIVACY flag to be lost if IFA_F_OPTIMISTIC is set.
Cc: Erik Kline <ek@google.com> Cc: Fernando Gont <fgont@si6networks.com> Cc: Lorenzo Colitti <lorenzo@google.com> Cc: YOSHIFUJI Hideaki/吉藤英明 <hideaki.yoshifuji@miraclelinux.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Fixes: 64236f3f3d74 ("ipv6: introduce IFA_F_STABLE_PRIVACY flag") Signed-off-by: Bjørn Mork <bjorn@mork.no> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
There is a memleak when suspend/resume this driver version.
Currently the stmmac, during resume step, reallocates all the resources
but they are not released when suspend.
The patch is not to release these resources but the logic has been changed.
In fact, it is not necessary to free and reallocate all from scratch
because the memory data will be always preserved.
As final solution, the patch just reinit the descriptors and the rx/tx
pointers only when resume. Tested done on STi boxes.
Reported-by: ZhengShunQian <zhengsq@rock-chips.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
This is because netdev_alloc_skb() fails and 'mdp->rx_skbuff[entry]' is left
NULL but sh_eth_rx() later uses it without checking. Add such check...
Reported-by: Yasushi SHOJI <yashi@atmark-techno.com> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 5 Dec 2015 22:39:31 +0000 (17:39 -0500)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-12-03
This series contains updates to ixgbe, i40e/i40evf, MAINTAINERS and e100.txt
Alex provides a fix for ixgbe where enabling SR-IOV and then bringing the
interface up was resulting in the PF MAC addresses getting into a bad state.
The workaround for this issue is to bring up the interface first and then
enable SR-IOV as this will trigger the reset in the existing code.
I clean up legacy license stuff in the e100.txt documentation and then
update the maintainers/reviewers list for our drivers.
Jesse fixes an issue with the i40e/i40evf drivers, where if the driver were
to happen to have a mutex held while the i40e_init_adminq() call was called,
the init_adminq might inadvertently call mutex_init on a lock that was held
which is a violation of the calling semantices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Machek [Fri, 4 Dec 2015 08:50:00 +0000 (09:50 +0100)]
atl1c: Improve driver not to do order 4 GFP_ATOMIC allocation
atl1c driver is doing order-4 allocation with GFP_ATOMIC
priority. That often breaks networking after resume. Switch to
GFP_KERNEL. Still not ideal, but should be significantly better.
atl1c_setup_ring_resources() is called from .open() function, and
already uses GFP_KERNEL, so this change is safe.
Signed-off-by: Pavel Machek <pavel@ucw.cz> Acked-by: Michal Hocko <mhocko@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Fri, 4 Dec 2015 14:39:56 +0000 (22:39 +0800)]
rhashtable: Use __vmalloc with GFP_ATOMIC for table allocation
When an rhashtable user pounds rhashtable hard with back-to-back
insertions we may end up growing the table in GFP_ATOMIC context.
Unfortunately when the table reaches a certain size this often
fails because we don't have enough physically contiguous pages
to hold the new table.
Eric Dumazet suggested (and in fact wrote this patch) using
__vmalloc instead which can be used in GFP_ATOMIC context.
Reported-by: Phil Sutter <phil@nwl.cc> Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 3 Dec 2015 16:21:50 +0000 (17:21 +0100)]
gre6: allow to update all parameters via rtnl
Parameters were updated only if the kernel was unable to find the tunnel
with the new parameters, ie only if core pamareters were updated (keys,
addr, link, type).
Now it's possible to update ttl, hoplimit, flowinfo and flags.
Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Andrew <nitr0@seti.kr.ua> Fixes: 287f3a943fef ("pppoe: Use workqueue to die properly when a PADT is received") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 4 Dec 2015 20:01:13 +0000 (15:01 -0500)]
Merge branch 'mvpp2-fixes'
Marcin Wojtas says:
====================
Marvell Armada 375 mvpp2 fixes
During my work on mvneta driver I revised mvpp2, and it occurred that the
initial version of Marvell Armada 375 SoC comprised bugs around
DMA-unmapping in both ingress and egress paths - not all buffers were
umapped in TX path and none(!) in RX. Three patches that I send fix
this situation.
Any feedback would be welcome.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Thu, 3 Dec 2015 14:20:51 +0000 (15:20 +0100)]
net: mvpp2: fix refilling BM pools in RX path
In hitherto code in case of RX buffer allocation error during refill,
original buffer is pushed to the network stack, but the amount of
available buffer pointers in BM pool is decreased.
This commit fixes the situation by moving refill call before skb_put(),
and returning original buffer pointer to the pool in case of an error.
Signed-off-by: Marcin Wojtas <mw@semihalf.com> Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375
network unit")
Cc: <stable@vger.kernel.org> # v3.18+ Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Thu, 3 Dec 2015 14:20:50 +0000 (15:20 +0100)]
net: mvpp2: fix buffers' DMA handling on RX path
Each allocated buffer, whose pointer is put into BM pool is DMA-mapped.
Hence it should be properly unmapped after usage or when removing buffers
from pool.
This commit fixes DMA handling on RX path by adding dma_unmap_single() in
mvpp2_rx() and in mvpp2_bufs_free(). The latter function's argument number
had to be increased for this purpose.
Signed-off-by: Marcin Wojtas <mw@semihalf.com> Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375
network unit")
Cc: <stable@vger.kernel.org> # v3.18+ Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Thu, 3 Dec 2015 14:20:49 +0000 (15:20 +0100)]
net: mvpp2: fix missing DMA region unmap in egress processing
The Tx descriptor release code currently calls dma_unmap_single() and
dev_kfree_skb_any() if the descriptor is associated with a non-NULL skb.
This condition is true only for the last fragment of the packet.
Since every descriptor's buffer is DMA-mapped it has to be properly
unmapped.
Signed-off-by: Marcin Wojtas <mw@semihalf.com> Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375
network unit")
Cc: <stable@vger.kernel.org> # v3.18+ Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Thu, 3 Dec 2015 12:41:29 +0000 (20:41 +0800)]
rhashtable: Prevent spurious EBUSY errors on insertion
Thomas and Phil observed that under stress rhashtable insertion
sometimes failed with EBUSY, even though this error should only
ever been seen when we're under attack and our hash chain length
has grown to an unacceptable level, even after a rehash.
It turns out that the logic for detecting whether there is an
existing rehash is faulty. In particular, when two threads both
try to grow the same table at the same time, one of them may see
the newly grown table and thus erroneously conclude that it had
been rehashed. This is what leads to the EBUSY error.
This patch fixes this by remembering the current last table we
used during insertion so that rhashtable_insert_rehash can detect
when another thread has also done a resize/rehash. When this is
detected we will give up our resize/rehash and simply retry the
insertion with the new table.
Reported-by: Thomas Graf <tgraf@suug.ch> Reported-by: Phil Sutter <phil@nwl.cc> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Tested-by: Phil Sutter <phil@nwl.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 3 Dec 2015 23:45:16 +0000 (15:45 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes from this series. The most important here is a
regression fix for an issue that some folks would hit in blk-merge.c,
and the NVMe queue depth limit for the screwed up Apple "nvme"
controller.
In more detail, this pull request contains:
- a set of fixes for null_blk, including a fix for a few corner cases
where we could hang the device. From Arianna and Paolo.
- lightnvm:
- A build improvement from Keith.
- Update the qemu pci id detection from Matias.
- Error handling fixes for leaks and other little fixes from
Sudip and Wenwei.
- fix from Eric where BLKRRPART would not return EBUSY for whole
device mounts, only when partitions were mounted.
- fix from Jan Kara, where EOF O_DIRECT reads would return
negatively.
- remove check for rq_mergeable() when checking limits for cloned
requests. The check doesn't make any sense. It's assuming that
since NOMERGE is set on the request that we don't have to
recalculate limits since the request didn't change, but that's not
true if the request has been redirected. From Hannes.
- correctly get the bio front segment value set for single segment
bio's, fixing a BUG() in blk-merge. From Ming"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme: temporary fix for Apple controller reset
null_blk: change type of completion_nsec to unsigned long
null_blk: guarantee device restart in all irq modes
null_blk: set a separate timer for each command
blk-merge: fix computing bio->bi_seg_front_size in case of single segment
direct-io: Fix negative return from dio read beyond eof
block: Always check queue limits for cloned requests
lightnvm: missing nvm_lock acquire
lightnvm: unconverted ppa returned in get_bb_tbl
lightnvm: refactor and change vendor id for qemu
lightnvm: do device max sectors boundary check first
lightnvm: fix ioctl memory leaks
lightnvm: free memory when gennvm register fails
lightnvm: Simplify config when disabled
Return EBUSY from BLKRRPART for mounted whole-dev fs
Linus Torvalds [Thu, 3 Dec 2015 23:23:17 +0000 (15:23 -0800)]
Merge tag 'trace-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"During the merge window I added a new file that is used to filter
trace events on pids. It filters all events where only tasks with
their pid in that file exists. It also handles the sched_switch and
sched_wakeup trace events where the current task does not have its pid
in the file, but the task either being switched to or awaken does.
Unfortunately, I forgot about sched_wakeup_new and sched_waking. Both
of these tracepoints use the same class as the sched_wakeup
tracepoint, and they too should be included in what gets filtered by
the set_event_pid file"
* tag 'trace-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Add sched_wakeup_new and sched_waking tracepoints for pid filter
Jesse Brandeburg [Wed, 18 Nov 2015 23:47:06 +0000 (15:47 -0800)]
i40e/i40evf: avoid mutex re-init
If the driver were to happen to have a mutex held while
the i40e_init_adminq call was called, the init_adminq might
inadvertently call mutex_init on a lock that was held
which is a violation of the calling semantics.
Fix this by avoiding adminq.c code allocating/freeing this memory, and
then do the same work only once in probe/remove.
Testing Hints (Required if no HSD): for VF, load i40evf in bare metal
and echo 32 > sriov_numvfs; echo 0 > sriov_numvfs in a loop. Yes this
is a horrible thing to do.
Change-ID: Ida263c51b34e195252179e7e5e400d73a99be7a2 Reported-by: Stefan Assmann <sassmann@redhat.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher [Tue, 10 Nov 2015 19:09:06 +0000 (11:09 -0800)]
MAINTAINERS: Update Intel Wired LAN reviewers
Since Matthew has moved on to other pastures and no longer works
for Intel, remove him from the list of reviewers and add Bruce
Allan as his replacement.
CC: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher [Mon, 9 Nov 2015 13:03:47 +0000 (05:03 -0800)]
e100.txt: Cleanup license info in kernel doc
Apparently the e100.txt document contained a "License" section left
over from days of old, which does not need to be in the kernel
documentation. So clean it up..
CC: John Ronciak <john.ronciak@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com>
David S. Miller [Thu, 3 Dec 2015 20:56:22 +0000 (15:56 -0500)]
Merge tag 'mac80211-for-davem-2015-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A small set of fixes for 4.4:
* fix scanning in mac80211 to not actively scan radar
channels (from Antonio)
* fix uninitialized variable in remain-on-channel that
could lead to treating frame TX as remain-on-channel
and not sending the frame at all
* remove NL80211_FEATURE_FULL_AP_CLIENT_STATE again, it
was broken and needs more work, we'll enable it later
* fix call_rcu() induced use-after-reset/free in mesh
(that was suddenly causing issues in certain tests)
* always request block-ack window size 64 as we found
some APs will otherwise crash (really ...)
* fix P2P-Device teardown sequence to avoid restarting
with uninitialized data
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Tue, 20 Oct 2015 20:28:17 +0000 (13:28 -0700)]
ixgbe: Reset interface after enabling SR-IOV
Enabling SR-IOV and then bringing the interface up was resulting in the PF
MAC addresses getting into a bad state. Specifically the MAC address was
enabled for both VF 0 and the PF. This resulted in some odd behaviors such
as VF 0 receiving a copy of the PFs traffic, which in turn enables the
ability for VF 0 to spoof the PF.
A workaround for this issue appears to be to bring up the interface first
and then enable SR-IOV as this way the reset is then triggered in the
existing code.
In order to correct this I have added a change to ixgbe_setup_tc where if
the interface is down we still will at least call ixgbe_reset so that the
MAC addresses for the device are reset to the correct pools.
Expected Result, behavior after patch:
MPSAR[0] 00000080
MPSAR[254] 00000080
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jérôme Pouiller [Thu, 3 Dec 2015 09:02:35 +0000 (10:02 +0100)]
net: phy: reset only targeted phy
It is possible to address another chip on same MDIO bus. The case is
correctly handled for media advertising. It is taken into account
only if mii_data->phy_id == phydev->addr. However, this condition
was missing for reset case.
Signed-off-by: Jérôme Pouiller <jezz@sysmic.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-eoan-kernel.git / log