ipv6: addrconf: fix dev refcont leak when DAD failed
In general, when DAD detected IPv6 duplicate address, ifp->state
will be set to INET6_IFADDR_STATE_ERRDAD and DAD is stopped by a
delayed work, the call tree should be like this:
ndisc_recv_ns
-> addrconf_dad_failure <- missing ifp put
-> addrconf_mod_dad_work
-> schedule addrconf_dad_work()
-> addrconf_dad_stop() <- missing ifp hold before call it
addrconf_dad_failure() called with ifp refcont holding but not put.
addrconf_dad_work() call addrconf_dad_stop() without extra holding
refcount. This will not cause any issue normally.
But the race between addrconf_dad_failure() and addrconf_dad_work()
may cause ifp refcount leak and netdevice can not be unregister,
dmesg show the following messages:
IPv6: eth0: IPv6 duplicate address fe80::XX:XXXX:XXXX:XX detected!
...
unregister_netdevice: waiting for eth0 to become free. Usage count = 1
Cc: stable@vger.kernel.org Fixes: c15b1ccadb32 ("ipv6: move DAD and addrconf_verify processing
to workqueue") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 5 Sep 2016 05:57:35 +0000 (01:57 -0400)]
bnxt_en: Fix TX push operation on ARM64.
There is a code path where we are calling __iowrite64_copy() on
an address that is not 64-bit aligned. This causes an exception on
some architectures such as arm64. Fix that code path by using
__iowrite32_copy().
Reported-by: JD Zheng <jiandong.zheng@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Tomlinson [Sun, 4 Sep 2016 22:20:20 +0000 (10:20 +1200)]
net: Don't delete routes in different VRFs
When deleting an IP address from an interface, there is a clean-up of
routes which refer to this local address. However, there was no check to
see that the VRF matched. This meant that deletion wasn't confined to
the VRF it should have been.
To solve this, a new field has been added to fib_info to hold a table
id. When removing fib entries corresponding to a local ip address, this
table id is also used in the comparison.
The table id is populated when the fib_info is created. This was already
done in some places, but not in ip_rt_ioctl(). This has now been fixed.
Fixes: 021dd3b8a142 ("net: Add routes to the table associated with the device") Acked-by: David Ahern <dsa@cumulusnetworks.com> Tested-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
net: macb: initialize checksum when using checksum offloading
I'm still struggling to get this fix right..
Changes since v2:
- do not blindly modify SKB contents according to Dave's legitimate
objection
Changes since v1:
- dropped disabling HW checksum offload for Zynq
- initialize checksum similar to net/ethernet/freescale/fec_main.c
-- >8 --
MACB/GEM needs the checksum field initialized to 0 to get correct
results on transmit in all cases, e.g. on Zynq, UDP packets with
payload <= 2 otherwise contain a wrong checksums.
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Jones [Fri, 2 Sep 2016 18:39:50 +0000 (14:39 -0400)]
ipv6: release dst in ping_v6_sendmsg
Neither the failure or success paths of ping_v6_sendmsg release
the dst it acquires. This leads to a flood of warnings from
"net/core/dst.c:288 dst_release" on older kernels that
don't have 8bf4ada2e21378816b28205427ee6b0e1ca4c5f1 backported.
That patch optimistically hoped this had been fixed post 3.10, but
it seems at least one case wasn't, where I've seen this triggered
a lot from machines doing unprivileged icmp sockets.
Cc: Martin Lau <kafai@fb.com> Signed-off-by: Dave Jones <davej@codemonkey.org.uk> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
af_unix: split 'u->readlock' into two: 'iolock' and 'bindlock'
Right now we use the 'readlock' both for protecting some of the af_unix
IO path and for making the bind be single-threaded.
The two are independent, but using the same lock makes for a nasty
deadlock due to ordering with regards to filesystem locking. The bind
locking would want to nest outside the VSF pathname locking, but the IO
locking wants to nest inside some of those same locks.
We tried to fix this earlier with commit c845acb324aa ("af_unix: Fix
splice-bind deadlock") which moved the readlock inside the vfs locks,
but that caused problems with overlayfs that will then call back into
filesystem routines that take the lock in the wrong order anyway.
Splitting the locks means that we can go back to having the bind lock be
the outermost lock, and we don't have any deadlocks with lock ordering.
Acked-by: Rainer Weikusat <rweikusat@cyberadapt.com> Acked-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that it just replaces one deadlock with another one: we can
still get the wrong lock ordering with the readlock due to overlayfs
calling back into the filesystem layer and still taking the vfs locks
after the readlock.
The proper solution ends up being to just split the readlock into two
pieces: the bind lock (taken *outside* the vfs locks) and the IO lock
(taken *inside* the filesystem locks). The two locks are independent
anyway.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 4 Sep 2016 18:42:57 +0000 (11:42 -0700)]
Merge branch 'vxlan-fixes'
Jiri Benc says:
====================
vxlan: fix error reporting
This patchset improves checking for invalid configuration in VXLAN and
fixes problems with duplicated and inappropriate error messages.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan_dev_configure outputs error messages before returning, no need to
print again the same mesages in vxlan_newlink. Also, vxlan_dev_configure may
return a particular error code for a different reason than vxlan_newlink
thinks.
Move the remaining error messages into vxlan_dev_configure and let
vxlan_newlink just pass on the error code.
Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan: reject multicast destination without an interface
Currently, kernel accepts configurations such as:
ip l a type vxlan dstport 4789 id 1 group 239.192.0.1
ip l a type vxlan dstport 4789 id 1 group ff0e::110
However, neither of those really works. In the IPv4 case, the interface
cannot be brought up ("RTNETLINK answers: No such device"). This is because
multicast join will be rejected without the interface being specified.
In the IPv6 case, multicast wil be joined on the first interface found. This
is not what the user wants as it depends on random factors (order of
interfaces).
Note that it's possible to add a local address but it doesn't solve
anything. For IPv4, it's not considered in the multicast join (thus the same
error as above is returned on ifup). This could be added but it wouldn't
help for IPv6 anyway. For IPv6, we do need the interface.
Just reject a configuration that sets multicast address and does not provide
an interface. Nobody can depend on the previous behavior as it never worked.
Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(a) Create bonding master
> modprobe bonding miimon=50
(b) Create macvlan bridge on eth2
> ip link add link eth2 dev mvl0 address aa:0:0:0:0:01 \
type macvlan
(c) Now try adding eth2 into the bond
> echo +eth2 > /sys/class/net/bond0/bonding/slaves
<crash>
Bonding does lots of things before checking if the device enslaved is
busy or not.
In this case when the notifier call-chain sends notifications, the
bond_netdev_event() assumes that the rx_handler /rx_handler_data is
registered while the bond_enslave() hasn't progressed far enough to
register rx_handler for the new slave.
This patch adds a rx_handler check that can be performed right at the
beginning of the enslave code to avoid getting into this situation.
Signed-off-by: Mahesh Bandewar <maheshb@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 3 Sep 2016 00:28:34 +0000 (17:28 -0700)]
Merge branch 'smsc911x-fixes'
Jeremy Linton says:
====================
net: smsc911x: Move phy and interrupt config
v2-v3: Move error handing into separate patch, replace a couple cases
of fixed errors with the errors being returned from the failing functions.
Hoist irq handler.
The smsc911x driver is doing a number of things in its probe routine that
should be delayed until the interface is started. Because of this, the module
cannot be unloaded, the phy states are incorrect/stale if the interface isn't
running, open's unnecessarily fail causing network configuration problems, and
the /proc/irq nodes are incorrectly named.
Clean up a number of these problems by moving the mdio and interrupt
configuration into the smsc911x_open routine.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeremy Linton [Thu, 1 Sep 2016 20:15:09 +0000 (15:15 -0500)]
net: smsc911x: Move interrupt allocation to open/stop
The /proc/irq/xx information is incorrect for smsc911x because
the request_irq is happening before the register_netdev has the
proper device name. Moving it to the open also fixes the case
of when the device is renamed.
Reported-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Jeremy Linton <jeremy.linton@arm.com> Tested-by: Will Deacon <will.deacon@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Move phy startup/shutdown into the smsc911x_open/stop routines. This
allows the module to be unloaded because phy_connect_direct is no longer
always holding the module use count. This one change also resolves a
number of other problems.
The link status of a downed interface no longer reflects a stale state.
Errors caused by the net device being opened before the mdio/phy was
configured. There is also a potential power savings as the phy's don't
remain powered when the interface isn't running.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tunnel deletion is delayed by both a workqueue (l2tp_tunnel_delete -> wq
-> l2tp_tunnel_del_work) and RCU (sk_destruct -> RCU ->
l2tp_tunnel_destruct).
By the time l2tp_tunnel_destruct() runs to destroy the tunnel and finish
destroying the socket, the private data reserved via the net_generic
mechanism has already been freed, but l2tp_tunnel_destruct() actually
uses this data.
Make sure tunnel deletion for the netns has completed before returning
from l2tp_exit_net() by first flushing the tunnel removal workqueue, and
then waiting for RCU callbacks to complete.
Fixes: 167eb17e0b17 ("l2tp: create tunnel sockets in the right namespace") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cooper [Fri, 26 Aug 2016 15:52:29 +0000 (23:52 +0800)]
ipv6: Don't unset flowi6_proto in ipxip6_tnl_xmit()
Commit 8eb30be0352d0916 ("ipv6: Create ip6_tnl_xmit") unsets
flowi6_proto in ip4ip6_tnl_xmit() and ip6ip6_tnl_xmit().
Since xfrm_selector_match() relies on this info, IPv6 packets
sent by an ip6tunnel cannot be properly selected by their
protocols after removing it. This patch puts flowi6_proto back.
Cc: stable@vger.kernel.org Fixes: 8eb30be0352d ("ipv6: Create ip6_tnl_xmit") Signed-off-by: Eli Cooper <elicooper@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x: don't reset chip on cleanup if PCI function is offline
When PCI error is detected, in some architectures (like PowerPC) a slot
reset is performed - the driver's error handlers are in charge of "disable"
device before the reset, and re-enable it after a successful slot reset.
There are two cases though that another path is taken on the code: if the
slot reset is not successful or if too many errors already happened in the
specific adapter (meaning that possibly the device is experiencing a HW
failure that slot reset is not able to solve), the core PCI error mechanism
(called EEH in PowerPC) will remove the adapter from the system, since it
will consider this as a permanent failure on device. In this case, a path
is taken that leads to bnx2x_chip_cleanup() calling bnx2x_reset_hw(), which
then tries to perform a HW reset on chip. This reset won't succeed since
the HW is in a fault state, which can be seen by multiple messages on
kernel log like below:
bnx2x: [bnx2x_issue_dmae_with_comp:552(eth1)]DMAE timeout!
bnx2x: [bnx2x_write_dmae:600(eth1)]DMAE returned failure -1
After some time, the PCI error mechanism gives up on waiting the driver's
correct removal procedure and forcibly remove the adapter from the system.
We can see soft lockup while core PCI error mechanism is waiting for driver
to accomplish the right removal process.
This patch adds a verification to avoid a chip reset whenever the function
is in PCI error state - since this case is only reached when we have a
device being removed because of a permanent failure, the HW chip reset is
not expected to work fine neither is necessary.
Also, as a minor improvement in error path, we avoid the MCP information dump
in case of non-recoverable PCI error (when adapter is about to be removed),
since it will certainly fail.
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com> Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Acked-By: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gao Feng [Wed, 31 Aug 2016 06:15:05 +0000 (14:15 +0800)]
rps: flow_dissector: Fix uninitialized flow_keys used in __skb_get_hash possibly
The original codes depend on that the function parameters are evaluated from
left to right. But the parameter's evaluation order is not defined in C
standard actually.
When flow_keys_have_l4(&keys) is invoked before ___skb_get_hash(skb, &keys,
hashrnd) with some compilers or environment, the keys passed to
flow_keys_have_l4 is not initialized.
Fixes: 6db61d79c1e1 ("flow_dissector: Ignore flow dissector return value from ___skb_get_hash") Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Gao Feng <fgao@ikuai8.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neal Cardwell [Tue, 30 Aug 2016 15:55:23 +0000 (11:55 -0400)]
tcp: fastopen: fix rcv_wup initialization for TFO server on SYN/data
Yuchung noticed that on the first TFO server data packet sent after
the (TFO) handshake, the server echoed the TCP timestamp value in the
SYN/data instead of the timestamp value in the final ACK of the
handshake. This problem did not happen on regular opens.
The tcp_replace_ts_recent() logic that decides whether to remember an
incoming TS value needs tp->rcv_wup to hold the latest receive
sequence number that we have ACKed (latest tp->rcv_nxt we have
ACKed). This commit fixes this issue by ensuring that a TFO server
properly updates tp->rcv_wup to match tp->rcv_nxt at the time it sends
a SYN/ACK for the SYN/data.
Reported-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Fixes: 168a8f58059a ("tcp: TCP Fast Open Server - main code path") Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: don't increment tx_dropped in br_do_proxy_arp
pskb_may_pull may fail due to various reasons (e.g. alloc failure), but the
skb isn't changed/dropped and processing continues so we shouldn't
increment tx_dropped.
CC: Kyeyoon Park <kyeyoonp@codeaurora.org> CC: Roopa Prabhu <roopa@cumulusnetworks.com> CC: Stephen Hemminger <stephen@networkplumber.org> CC: bridge@lists.linux-foundation.org Fixes: 958501163ddd ("bridge: Add support for IEEE 802.11 Proxy ARP") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Tue, 30 Aug 2016 08:09:21 +0000 (10:09 +0200)]
ipv6: add missing netconf notif when 'all' is updated
The 'default' value was not advertised.
Fixes: f3a1bfb11ccb ("rtnl/ipv6: use netconf msg to advertise forwarding status") Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Tue, 30 Aug 2016 06:06:27 +0000 (11:36 +0530)]
net: thunderx: Fix for issues with multiple CQEs posted for a TSO packet
On ThunderX 88xx pass 2.x chips when TSO is offloaded to HW,
HW posts a CQE for every TSO segment transmitted. Current code
does handles this, but is prone to issues when segment sizes are
small resulting in SW processing too many CQEs and also at times
frees a SKB which is not yet transmitted.
This patch handles the errata in a different way and eliminates issues
with earlier approach, TSO packet is submitted to HW with post_cqe=0,
so that no CQE is posted upon completion of transmission of TSO packet
but a additional HDR + IMMEDIATE descriptors are added to SQ due to
which a CQE is posted and will have required info to be used while
cleanup in napi. This way only one CQE is posted for a TSO packet.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Tue, 30 Aug 2016 06:06:26 +0000 (11:36 +0530)]
net: thunderx: Fix for HW issue while padding TSO packet
There is a issue in HW where-in while sending GSO sized pkts
as part of TSO, if pkt len falls below configured min packet
size i.e 60, NIC will zero PAD packet and also updates IP total length.
Hence set this value to lessthan min pkt size of MAC + IP + TCP
headers, BGX will anyway do the padding to transmit 64 byte pkt
including FCS.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Ertman [Tue, 30 Aug 2016 00:38:26 +0000 (17:38 -0700)]
i40e: Fix kernel panic on enable/disable LLDP
If DCB is configured on the link partner switch with an
unsupported traffic class configuration (e.g. non-contiguous TCs),
the driver is flagging DCB as disabled. But, for future DCB
LLDPDUs, the driver was checking if the interface was DCB capable
instead of enabled. This was causing a kernel panic when LLDP
was enabled/disabled on the link partner switch.
This patch corrects the situation by having the LLDP event handler
check the correct flag in the pf structure. It also cleans up the
setting and clearing of the enabled flag for other checks.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tipc: fix random link resets while adding a second bearer
In a dual bearer configuration, if the second tipc link becomes
active while the first link still has pending nametable "bulk"
updates, it randomly leads to reset of the second link.
When a link is established, the function named_distribute(),
fills the skb based on node mtu (allows room for TUNNEL_PROTOCOL)
with NAME_DISTRIBUTOR message for each PUBLICATION.
However, the function named_distribute() allocates the buffer by
increasing the node mtu by INT_H_SIZE (to insert NAME_DISTRIBUTOR).
This consumes the space allocated for TUNNEL_PROTOCOL.
When establishing the second link, the link shall tunnel all the
messages in the first link queue including the "bulk" update.
As size of the NAME_DISTRIBUTOR messages while tunnelling, exceeds
the link mtu the transmission fails (-EMSGSIZE).
Thus, the synch point based on the message count of the tunnel
packets is never reached leading to link timeout.
In this commit, we adjust the size of name distributor message so that
they can be tunnelled.
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Thu, 1 Sep 2016 09:28:59 +0000 (11:28 +0200)]
tg3: Fix for disallow tx coalescing time to be 0
The recent commit 087d7a8c9174 "tg3: Fix for diasllow rx coalescing
time to be 0" disallow to set Rx coalescing time to be 0 as this stops
generating interrupts for the incoming packets. I found the zero
Tx coalescing time stops generating interrupts for outgoing packets
as well and fires Tx watchdog later. To avoid this, don't allow to set
Tx coalescing time to 0 and also remove subsequent checks that become
senseless.
Cc: satish.baddipadige@broadcom.com Cc: siva.kallam@broadcom.com Cc: michael.chan@broadcom.com Signed-off-by: Ivan Vecera <ivecera@redhat.com> Acked-by: Siva Reddy Kallam <siva.kallam@broadcom.com> Acked-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/qlogic/qed/qed_dcbx.c:1230:13-20: WARNING: kzalloc should be used for dcbx_info, instead of kmalloc/memset
drivers/net/ethernet/qlogic/qed/qed_dcbx.c:1192:13-20: WARNING: kzalloc should be used for dcbx_info, instead of kmalloc/memset
Use kzalloc rather than kmalloc followed by memset with 0
This considers some simple cases that are common and easy to validate
Note in particular that there are no ...s in the rule, so all of the
matched code has to be contiguous
mlxsw: spectrum: Use existing flood setup when adding VLANs
When a VLAN is added on a bridge port we should use the existing unicast
flood configuration of the port instead of assuming it's enabled.
Fixes: 0293038e0c36 ("mlxsw: spectrum: Add support for flood control") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Don't take multiple references on a FID
In commit 14d39461b3f4 ("mlxsw: spectrum: Use per-FID struct for the
VLAN-aware bridge") I added a per-FID struct, which member ports can
take a reference on upon VLAN membership configuration.
However, sometimes only the VLAN flags (e.g. egress untagged) are
toggled without changing the VLAN membership. In these cases we
shouldn't take another reference on the FID.
Fixes: 14d39461b3f4 ("mlxsw: spectrum: Use per-FID struct for the VLAN-aware bridge") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Fix error path in mlxsw_sp_module_init
Add forgotten notifier unregister.
Fixes: 99724c18fc66 ("mlxsw: spectrum: Introduce support for router interfaces") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Originally, I expected that there would be needed to call update
operation in case RALUE record action is changed. However, that is not
needed since write operation takes care of that nicely. Remove prepared
construct and always call the write operation.
Fixes: 61c503f976b5 ("mlxsw: spectrum_router: Implement fib4 add/del switchdev obj ops") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_router: Fix failure caused by double fib removal from HW
In mlxsw we squash tables 254 and 255 together into HW. Kernel adds/dels
/32 ip to/from both 254 and 255. On del path, that causes the same
prefix being removed twice. Fix this by introducing reference counting
for private mlxsw fib entries. That required a bit of code reshuffle.
Also put dev into fib entry key so the same prefix could be represented
once per every router interface.
Fixes: 61c503f976b5 ("mlxsw: spectrum_router: Implement fib4 add/del switchdev obj ops") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch takes care of clearing the uninitialized buffer before using it.
1. pfc pri-enable bitmap need to be cleared before setting the requested
enable bits. Without this, the un-touched values will be merged with
requested values and sent to MFW.
2. The data in app-entry field need to be cleared before using it.
3. Clear the output data buffer used in qed_dcbx_query_params().
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qed: Set selection-field while configuring the app entry in ieee mode.
Management firmware requires the selection-field (SF) to be set for
configuring the application/protocol entry in IEEE mode. Without this
setting, the app entry will be configured incorrectly in MFW.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qed*: Disallow dcbx configuration for VF interfaces.
Dcbx configuration is not supported for VF interfaces. Hence don't populate
the callbacks for VFs and also fail the dcbx-query for VFs.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This is because on the error path, after we install
the new socket file, we call sock_release() to clean
up the socket, which leaves the fd pointing to a freed
socket. Fix this by calling sys_close() on that fd
directly.
Fixes: ab7ac4eb9832 ("kcm: Kernel Connection Multiplexor module") Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Tom Herbert <tom@herbertland.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 1 Sep 2016 03:53:49 +0000 (20:53 -0700)]
Merge branch 'mediatek-fixes'
Sean Wang says:
====================
net: ethernet: mediatek: a couple of fixes
a couple of fixes come out from integrating with linux-4.8 rc1
they all are verified and workable on linux-4.8 rc1
Changes since v1:
- usage of loops to work out if all required clock are ready instead
of tedious coding
- remove redundant pinctrl setup that is already done by core driver
thanks for careful and patient reviewing by Andrew Lunn
- splitting distinct changes into the separate patches
- change variable naming from err to ret for readable coding
Changes since v2:
- restore to original clock disabling sequence that is changed
accidentally in the last version
- refine the commit log that would cause misunderstanding what has
been done in the changes
- refine the commit log that would cause footnote losing due to
improper delimiter use
Changes since v3:
- fix git rejects caused by mixing a change from net-next, so
remake the patch set based on the current net branch again.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Return -ENODEV if the MDIO bus is disabled in the device tree.
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Acked-by: John Crispin <john@phrozen.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Wang [Thu, 1 Sep 2016 02:47:34 +0000 (10:47 +0800)]
net: ethernet: mediatek: use devm_mdiobus_alloc instead of mdiobus_alloc inside mtk_mdio_init
a lot of parts in the driver uses devm_* APIs to gain benefits from the
device resource management, so devm_mdiobus_alloc is also used instead
of mdiobus_alloc to have more elegant code flow.
Using common code provided by the devm_* helps to
1) have simplified the code flow as [1] says
2) decrease the risk of incorrect error handling by human
3) only a few drivers used it since it was proposed on linux 3.16,
so just hope to promote for this.
Sean Wang [Thu, 1 Sep 2016 02:47:30 +0000 (10:47 +0800)]
net: ethernet: mediatek: remove redundant free_irq for devm_request_irq allocated irq
these irqs are not used for shared irq and disabled during ethernet stops.
irq requested by devm_request_irq is safe to be freed automatically on
driver detach.
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Acked-by: John Crispin <john@phrozen.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Wang [Thu, 1 Sep 2016 02:47:28 +0000 (10:47 +0800)]
net: ethernet: mediatek: fix incorrect return value of devm_clk_get with EPROBE_DEFER
1) If the return value of devm_clk_get is EPROBE_DEFER, we should
defer probing the driver. The change is verified and works based
on 4.8-rc1 staying with the latest clk-next code for MT7623.
2) Changing with the usage of loops to work out if all clocks
required are fine
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Wang [Thu, 1 Sep 2016 02:47:27 +0000 (10:47 +0800)]
net: ethernet: mediatek: fix fails from TX housekeeping due to incorrect port setup
which net device the SKB is complete for depends on the forward port
on txd4 on the corresponding TX descriptor, but the information isn't
set up well in case of SKB fragments that would lead to watchdog timeout
from the upper layer, so fix it up.
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Acked-by: John Crispin <john@phrozen.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Wed, 31 Aug 2016 12:16:44 +0000 (14:16 +0200)]
bridge: re-introduce 'fix parsing of MLDv2 reports'
commit bc8c20acaea1 ("bridge: multicast: treat igmpv3 report with
INCLUDE and no sources as a leave") seems to have accidentally reverted
commit 47cc84ce0c2f ("bridge: fix parsing of MLDv2 reports"). This
commit brings back a change to br_ip6_multicast_mld2_report() where
parsing of MLDv2 reports stops when the first group is successfully
added to the MDB cache.
Fixes: bc8c20acaea1 ("bridge: multicast: treat igmpv3 report with INCLUDE and no sources as a leave") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 31 Aug 2016 04:34:48 +0000 (21:34 -0700)]
Merge tag 'mac80211-for-davem-2016-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Three little fixes:
* revert a recent wext patch, which Ben Hutchings noticed was
wrong, and it turns out not to be necessary for any driver
* fix an infinite loop that can occur under certain conditions
in mac80211's TDLS code (depending on regulatory information)
* add a cfg80211_get_station() static inline when cfg80211 isn't
built, to allow other modules to not have to depend on it for it
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We have already use skb_header_pointer to get the ip header pointer,
so there's no need to use ip_hdr again. Moreover, in NETDEV INGRESS
hook, ip header maybe not linear, so use ip_hdr is not appropriate,
remove it.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Linus Torvalds [Tue, 30 Aug 2016 02:12:35 +0000 (19:12 -0700)]
Merge tag 'hwmon-for-linus-v4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Add missing sysfs attribute group terminator to it87 driver"
* tag 'hwmon-for-linus-v4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (it87) Add missing sysfs attribute group terminator
Linus Torvalds [Mon, 29 Aug 2016 19:37:11 +0000 (12:37 -0700)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Fix bugs that could cause kernel deadlocks or file system corruption
while moving xattrs to expand the extended inode.
Also add some sanity checks to the block group descriptors to make
sure we don't end up overwriting the superblock"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: avoid deadlock when expanding inode size
ext4: properly align shifted xattrs when expanding inodes
ext4: fix xattr shifting when expanding inodes part 2
ext4: fix xattr shifting when expanding inodes
ext4: validate that metadata blocks do not overlap superblock
ext4: reserve xattr index for the Hurd
1) Segregate namespaces properly in conntrack dumps, from Liping Zhang.
2) tcp listener refcount fix in netfilter tproxy, from Eric Dumazet.
3) Fix timeouts in qed driver due to xmit_more, from Yuval Mintz.
4) Fix use-after-free in tcp_xmit_retransmit_queue().
5) Userspace header fixups (use of __u32, missing includes, etc.) from
Mikko Rapeli.
6) Further refinements to fragmentation wrt gso and tunnels, from
Shmulik Ladkani.
7) Trigger poll correctly for zero length UDP packets, from Eric
Dumazet.
8) TCP window scaling fix, also from Eric Dumazet.
9) SLAB_DESTROY_BY_RCU is not relevant any more for UDP sockets.
10) Module refcount leak in qdisc_create_dflt(), from Eric Dumazet.
11) Fix deadlock in cp_rx_poll() of 8139cp driver, from Gao Feng.
12) Memory leak in rhashtable's alloc_bucket_locks(), from Eric Dumazet.
13) Add new device ID to alx driver, from Owen Lin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (83 commits)
Add Killer E2500 device ID in alx driver.
net: smc91x: fix SMC accesses
Documentation: networking: dsa: Remove platform device TODO
net/mlx5: Increase number of ethtool steering priorities
net/mlx5: Add error prints when validate ETS failed
net/mlx5e: Fix memory leak if refreshing TIRs fails
net/mlx5e: Add ethtool counter for TX xmit_more
net/mlx5e: Fix ethtool -g/G rx ring parameter report with striding RQ
net/mlx5e: Don't wait for SQ completions on close
net/mlx5e: Don't post fragmented MPWQE when RQ is disabled
net/mlx5e: Don't wait for RQ completions on close
net/mlx5e: Limit UMR length to the device's limitation
rhashtable: fix a memory leak in alloc_bucket_locks()
sfc: fix potential stack corruption from running past stat bitmask
team: loadbalance: push lacpdus to exact delivery
net: hns: dereference ppe_cb->ppe_common_cb if it is non-null
8139cp: Fix one possible deadloop in cp_rx_poll
i40e: Change some init flow for the client
Revert "phy: IRQ cannot be shared"
net: dsa: bcm_sf2: Fix race condition while unmasking interrupts
...
Linus Torvalds [Mon, 29 Aug 2016 19:20:22 +0000 (12:20 -0700)]
Merge tag 'platform-drivers-x86-v4.8-4' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Remove module related code from two drivers that are only configurable
as built-in: intel_pmic_gpio and platform/olpc"
* tag 'platform-drivers-x86-v4.8-4' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
intel_pmic_gpio: Make explicitly non-modular
platform/olpc: Make ec explicitly non-modular
Linus Torvalds [Mon, 29 Aug 2016 19:12:15 +0000 (12:12 -0700)]
Merge tag 'powerpc-4.8-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Ben Herrenschmidt:
"This was meant to be sent early last week, but I has a change pending
on one of the fixes and other things made me forget all about. Ugh.
We have some misc fixes for powerpc 4.8. Some trivial bits and some
regressions, and a trivial cleanup or two that I saw no point in
letting rot in patchwork"
* tag 'powerpc-4.8-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: signals: Discard transaction state from signal frames
powerpc/powernv : Drop reference added by kset_find_obj()
powerpc/tm: do not use r13 for tabort_syscall
powerpc: move hmi.c to arch/powerpc/kvm/
powerpc: sysdev: cpm: fix gpio save_regs functions
powerpc/pseries: PACA save area fix for MCE vs MCE
powerpc/pseries: PACA save area fix for general exception vs MCE
powerpc/prom: Fix sub-processor option passed to ibm, client-architecture-support
powerpc, hotplug: Avoid to touch non-existent cpumasks.
powerpc: migrate exception table users off module.h and onto extable.h
powerpc/powernv/pci: fix iterator signedness
powerpc/pseries: use pci_host_bridge.release_fn() to kfree(phb)
cxl: use pcibios_free_controller_deferred() when removing vPHBs
powerpc: mpc8349emitx: Delete unnecessary assignment for the field "owner"
powerpc/512x: Delete unnecessary assignment for the field "owner"
drivers/macintosh: Delete owner assignment
powerpc: cputhreads: Add missing include file
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
We don't replace module.h with init.h since the file already has that.
Cc: Alek Du <alek.du@intel.com> Cc: platform-driver-x86@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Paul Gortmaker [Mon, 15 Aug 2016 22:25:17 +0000 (18:25 -0400)]
platform/olpc: Make ec explicitly non-modular
The Kconfig entry controlling compilation of this code is:
arch/x86/Kconfig:config OLPC
arch/x86/Kconfig: bool "One Laptop Per Child support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: platform-driver-x86@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Acked-by: Andres Salomon <dilinger@queued.net> Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Russell King [Sat, 27 Aug 2016 16:33:03 +0000 (17:33 +0100)]
net: smc91x: fix SMC accesses
Commit b70661c70830 ("net: smc91x: use run-time configuration on all ARM
machines") broke some ARM platforms through several mistakes. Firstly,
the access size must correspond to the following rule:
(a) at least one of 16-bit or 8-bit access size must be supported
(b) 32-bit accesses are optional, and may be enabled in addition to
the above.
Secondly, it provides no emulation of 16-bit accesses, instead blindly
making 16-bit accesses even when the platform specifies that only 8-bit
is supported.
Reorganise smc91x.h so we can make use of the existing 16-bit access
emulation already provided - if 16-bit accesses are supported, use
16-bit accesses directly, otherwise if 8-bit accesses are supported,
use the provided 16-bit access emulation. If neither, BUG(). This
exactly reflects the driver behaviour prior to the commit being fixed.
Since the conversion incorrectly cut down the available access sizes on
several platforms, we also need to go through every platform and fix up
the overly-restrictive access size: Arnd assumed that if a platform can
perform 32-bit, 16-bit and 8-bit accesses, then only a 32-bit access
size needed to be specified - not so, all available access sizes must
be specified.
This likely fixes some performance regressions in doing this: if a
platform does not support 8-bit accesses, 8-bit accesses have been
emulated by performing a 16-bit read-modify-write access.
Tested on the Intel Assabet/Neponset platform, which supports only 8-bit
accesses, which was broken by the original commit.
Fixes: b70661c70830 ("net: smc91x: use run-time configuration on all ARM machines") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sat, 27 Aug 2016 22:34:20 +0000 (15:34 -0700)]
Documentation: networking: dsa: Remove platform device TODO
Since commit 83c0afaec7b7 ("net: dsa: Add new binding implementation"),
the shortcomings of the dsa platform device have been addressed, remove
that TODO item.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
This series contains some bug fixes for the mlx5 core and mlx5
ethernet driver.
From Saeed, Fix UMR to consider hardware translation table field
size limitation when calculating the maximum number of MTTs required
by the driver. Three patches to speed-up netdevice close time by
serializing channel (SQs & RQs) destruction rather than issuing and
waiting for hardware interrupts to free them.
From Eran, Fix ethtool ring parameter reporting for striding RQ layout.
Add error prints on ETS validation failure.
From Kamal, Fix memory leak on error flow.
From Maor, Fix ethtool steering priorities number.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Maor Gottlieb [Sun, 28 Aug 2016 22:13:50 +0000 (01:13 +0300)]
net/mlx5: Increase number of ethtool steering priorities
Ethtool has 11 flow tables, each flow table has its own priority.
Increase the number of priorities to be aligned with the number of flow
tables.
Fixes: 1174fce8d141 ('net/mlx5e: Support l3/l4 flow type specs in ethtool flow steering') Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eran Ben Elisha [Sun, 28 Aug 2016 22:13:49 +0000 (01:13 +0300)]
net/mlx5: Add error prints when validate ETS failed
Upon set ETS failure due to user invalid input, add error prints to
specify the exact error to the user.
Fixes: cdcf11212b22 ('net/mlx5e: Validate BW weight values of ETS') Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kamal Heib [Sun, 28 Aug 2016 22:13:48 +0000 (01:13 +0300)]
net/mlx5e: Fix memory leak if refreshing TIRs fails
Free 'in' command object also when mlx5_core_modify_tir fails.
Fixes: 724b2aa15126 ("net/mlx5e: TIRs management refactoring") Signed-off-by: Kamal Heib <kamalh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Sun, 28 Aug 2016 22:13:47 +0000 (01:13 +0300)]
net/mlx5e: Add ethtool counter for TX xmit_more
Add a counter in ethtool for the number of times that
TX xmit_more was used.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eran Ben Elisha [Sun, 28 Aug 2016 22:13:46 +0000 (01:13 +0300)]
net/mlx5e: Fix ethtool -g/G rx ring parameter report with striding RQ
The driver RQ has two possible configurations: striding RQ and
non-striding RQ. Until this patch, the driver always reported the
number of hardware WQEs (ring descriptors). For non striding RQ
configuration, this was OK since we have one WQE per pending packet
For striding RQ, multiple packets can fit into one WQE. For better
user experience we normalize the rx_pending parameter (size of wqe/mtu)
as the average ring size in case of striding RQ.
Fixes: 461017cb006a ('net/mlx5e: Support RX multi-packet WQE ...') Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Sun, 28 Aug 2016 22:13:45 +0000 (01:13 +0300)]
net/mlx5e: Don't wait for SQ completions on close
Instead of asking the firmware to flush the SQ (Send Queue) via
asynchronous completions when moved to error, we handle SQ flush
manually (mlx5e_free_tx_descs) same as we did when SQ flush got
timed out or on tx_timeout.
This will reduce SQs flush time and speedup interface down procedure.
Moved mlx5e_free_tx_descs to the end of en_tx.c for tx
critical code locality.
Fixes: 29429f3300a3 ('net/mlx5e: Timeout if SQ doesn't flush during close') Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Sun, 28 Aug 2016 22:13:44 +0000 (01:13 +0300)]
net/mlx5e: Don't post fragmented MPWQE when RQ is disabled
ICO (Internal control operations) SQ (Send Queue) is closed/disabled
after RQ (Receive Queue). After RQ is closed an ICO SQ completion
might post a fragmented MPWQE (Multi Packet Work Queue Element) into
that RQ.
As on regular RQ post, check if we are allowed to post to that
RQ (RQ is enabled). Cleanup in-progress UMR MPWQE on mlx5e_free_rx_descs
if needed.
Fixes: bc77b240b3c5 ('net/mlx5e: Add fragmented memory support for RX multi packet WQE') Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Sun, 28 Aug 2016 22:13:43 +0000 (01:13 +0300)]
net/mlx5e: Don't wait for RQ completions on close
This will significantly reduce receive queue flush time on interface
down.
Instead of asking the firmware to flush the RQ (Receive Queue) via
asynchronous completions when moved to error, we handle RQ flush
manually (mlx5e_free_rx_descs) same as we did when RQ flush got timed
out.
This will reduce RQs flush time and speedup interface down procedure
(ifconfig down) from 6 sec to 0.3 sec on a 48 cores system.
Moved mlx5e_free_rx_descs en_main.c where it is needed, to keep en_rx.c
free form non critical data path code for better code locality.
Fixes: 6cd392a082de ('net/mlx5e: Handle RQ flush in error cases') Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Sun, 28 Aug 2016 22:13:42 +0000 (01:13 +0300)]
net/mlx5e: Limit UMR length to the device's limitation
ConnectX-4 UMR (User Memory Region) MTT translation table offset in WQE
is limited to U16_MAX, before this patch we ignored that limitation and
requested the maximum possible UMR translation length that the netdev
might need (MAX channels * MAX pages per channel).
In case of a system with #cores > 32 and when linear WQE allocation fails,
falling back to using UMR WQEs will cause the RQ (Receive Queue) to get
stuck.
Here we limit UMR length to min(U16_MAX, max required pages) (while
considering the required alignments) on driver load, by default U16_MAX is
sufficient since the default RX rings value guarantees that we are in
range, dynamically (on set_ringparam/set_channels) we will check if the
new required UMR length (num mtts) is still in range, if not, fail the
request.
Fixes: bc77b240b3c5 ('net/mlx5e: Add fragmented memory support for RX multi packet WQE') Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cyril Bur [Tue, 23 Aug 2016 00:46:17 +0000 (10:46 +1000)]
powerpc: signals: Discard transaction state from signal frames
Userspace can begin and suspend a transaction within the signal
handler which means they might enter sys_rt_sigreturn() with the
processor in suspended state.
sys_rt_sigreturn() wants to restore process context (which may have
been in a transaction before signal delivery). To do this it must
restore TM SPRS. To achieve this, any transaction initiated within the
signal frame must be discarded in order to be able to restore TM SPRs
as TM SPRs can only be manipulated non-transactionally..
>From the PowerPC ISA:
TM Bad Thing Exception [Category: Transactional Memory]
An attempt is made to execute a mtspr targeting a TM register in
other than Non-transactional state.
It isn't clear exactly if there is really a use case for userspace
returning with a suspended transaction, however, doing so doesn't (on
its own) constitute a bad frame. As such, this patch simply discards
the transactional state of the context calling the sigreturn and
continues.
Mukesh Ojha [Mon, 22 Aug 2016 06:47:44 +0000 (12:17 +0530)]
powerpc/powernv : Drop reference added by kset_find_obj()
In a situation, where Linux kernel gets notified about duplicate error log
from OPAL, it is been observed that kernel fails to remove sysfs entries
(/sys/firmware/opal/elog/0xXXXXXXXX) of such error logs. This is because,
we currently search the error log/dump kobject in the kset list via
'kset_find_obj()' routine. Which eventually increment the reference count
by one, once it founds the kobject.
So, unless we decrement the reference count by one after it found the kobject,
we would not be able to release the kobject properly later.
This patch adds the 'kobject_put()' which was missing earlier.
Nicholas Piggin [Mon, 25 Jul 2016 04:26:51 +0000 (14:26 +1000)]
powerpc/tm: do not use r13 for tabort_syscall
tabort_syscall runs with RI=1, so a nested recoverable machine
check will load the paca into r13 and overwrite what we loaded
it with, because exceptions returning to privileged mode do not
restore r13.
Fixes: b4b56f9ecab4 (powerpc/tm: Abort syscalls in active transactions) Cc: stable@vger.kernel.org Signed-off-by: Nick Piggin <npiggin@gmail.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds [Sun, 28 Aug 2016 21:31:36 +0000 (14:31 -0700)]
Merge tag 'drm-fixes-for-4.8-rc4' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A bunch of fixes covering i915, amdgpu, one tegra and some core DRM
ones. Nothing too strange at this point"
* tag 'drm-fixes-for-4.8-rc4' of git://people.freedesktop.org/~airlied/linux: (21 commits)
drm/atomic: Don't potentially reset color_mgmt_changed on successive property updates.
drm: Protect fb_defio in drivers with CONFIG_KMS_FBDEV_EMULATION
drm/amdgpu: skip TV/CV in display parsing
drm/amdgpu: avoid a possible array overflow
drm/amdgpu: fix lru size grouping v2
drm/tegra: dsi: Enhance runtime power management
drm/i915: Fix botched merge that downgrades CSR versions.
drm/i915/skl: Ensure pipes with changed wms get added to the state
drm/i915/gen9: Only copy WM results for changed pipes to skl_hw
drm/i915/skl: Add support for the SAGV, fix underrun hangs
drm/i915/gen6+: Interpret mailbox error flags
drm/i915: Reattach comment, complete type specification
drm/i915: Unconditionally flush any chipset buffers before execbuf
drm/i915/gen9: Drop invalid WARN() during data rate calculation
drm/i915/gen9: Initialize intel_state->active_crtcs during WM sanitization (v2)
drm: Reject page_flip for !DRIVER_MODESET
drm/amdgpu: fix timeout value check in amd_sched_job_recovery
drm/amdgpu: fix sdma_v2_4_ring_test_ib
drm/amdgpu: fix amdgpu_move_blit on 32bit systems
drm/radeon: fix radeon_move_blit on 32bit systems
...
Mario Kleiner [Fri, 26 Aug 2016 23:02:28 +0000 (01:02 +0200)]
drm/atomic: Don't potentially reset color_mgmt_changed on successive property updates.
Due to assigning the 'replaced' value instead of or'ing it,
if drm_atomic_crtc_set_property() gets called multiple times,
the last call will define the color_mgmt_changed flag, so
a non-updating call to a property can reset the flag and
prevent actual hw state updates required by preceding
property updates.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: <stable@vger.kernel.org> # v4.6+ Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Sun, 28 Aug 2016 17:02:23 +0000 (10:02 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"A few fixes from the perf departement
- prevent a imbalanced preemption disable in the events teardown code
- prevent out of bound acces in perf userspace
- make perf tools compile with UCLIBC again
- a fix for the userspace unwinder utility"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Use this_cpu_ptr() when stopping AUX events
perf evsel: Do not access outside hw cache name arrays
tools lib: Reinstate strlcpy() header guard with __UCLIBC__
perf unwind: Use addr_location::addr instead of ip for entries
Linus Torvalds [Sun, 28 Aug 2016 16:52:40 +0000 (09:52 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"This lot provides:
- plug a hotplug race in the new affinity infrastructure
- a fix for the trigger type of chained interrupts
- plug a potential memory leak in the core code
- a few fixes for ARM and MIPS GICs"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mips-gic: Implement activate op for device domain
irqchip/mips-gic: Cleanup chip and handler setup
genirq/affinity: Use get/put_online_cpus around cpumask operations
genirq: Fix potential memleak when failing to get irq pm
irqchip/gicv3-its: Disable the ITS before initializing it
irqchip/gicv3: Remove disabling redistributor and group1 non-secure interrupts
irqchip/gic: Allow self-SGIs for SMP on UP configurations
genirq: Correctly configure the trigger on chained interrupts
Linus Torvalds [Sun, 28 Aug 2016 16:03:05 +0000 (09:03 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A few updates for timers & co:
- prevent a livelock in the timekeeping code when debugging is
enabled
- prevent out of bounds access in the timekeeping debug code
- various fixes in clocksource drivers
- a new maintainers entry"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/sun4i: Clear interrupts after stopping timer in probe function
drivers/clocksource/pistachio: Fix memory corruption in init
clocksource/drivers/timer-atmel-pit: Enable mck clock
clocksource/drivers/pxa: Fix include files for compilation
MAINTAINERS: Add ARM ARCHITECTED TIMER entry
timekeeping: Cap array access in timekeeping_debug
timekeeping: Avoid taking lock in NMI path with CONFIG_DEBUG_TIMEKEEPING
Linus Torvalds [Sat, 27 Aug 2016 22:51:50 +0000 (15:51 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"ARM:
- fixes for ITS init issues, error handling, IRQ leakage, race
conditions
- an erratum workaround for timers
- some removal of misleading use of errors and comments
- a fix for GICv3 on 32-bit guests
MIPS:
- fix for where the guest could wrongly map the first page of
physical memory
x86:
- nested virtualization fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
MIPS: KVM: Check for pfn noslot case
kvm: nVMX: fix nested tsc scaling
KVM: nVMX: postpone VMCS changes on MSR_IA32_APICBASE write
KVM: nVMX: fix msr bitmaps to prevent L2 from accessing L0 x2APIC
arm64: KVM: report configured SRE value to 32-bit world
arm64: KVM: remove misleading comment on pmu status
KVM: arm/arm64: timer: Workaround misconfigured timer interrupt
arm64: Document workaround for Cortex-A72 erratum #853709
KVM: arm/arm64: Change misleading use of is_error_pfn
KVM: arm64: ITS: avoid re-mapping LPIs
KVM: arm64: check for ITS device on MSI injection
KVM: arm64: ITS: move ITS registration into first VCPU run
KVM: arm64: vgic-its: Make updates to propbaser/pendbaser atomic
KVM: arm64: vgic-its: Plug race in vgic_put_irq
KVM: arm64: vgic-its: Handle errors from vgic_add_lpi
KVM: arm64: ITS: return 1 on successful MSI injection
Linus Torvalds [Sat, 27 Aug 2016 06:01:09 +0000 (23:01 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Round one of 4.8 rc fixes.
This should be the bulk of the -rc fixes for 4.8. I only have a few
things that are still outstanding (two ipoib bugs for which the
solution is not yet fully known, and a few queued items that came in
after my last push and I didn't want to delay this pull request for
late comers again).
Even though the patch count is kind of high, everything is minor fixes
so the overall churn is pretty low.
Summary:
- minor fixes to cxgb4
- minor fixes to mlx4
- one minor fix each to core, rxe, isert, srpt, mlx5, ocrdma, and usnic
- six or so fixes to i40iw fixes
- the rest are hfi1 fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (34 commits)
i40iw: Send last streaming mode message for loopback connections
IB/srpt: Update sport->port_guid with each port refresh
RDMA/ocrdma: Fix the max_sge reported from FW
i40iw: Avoid writing to freed memory
i40iw: Fix double free of allocated_buffer
IB/mlx5: Remove superfluous include of io-mapping.h
i40iw: Do not set self-referencing pointer to NULL after kfree
i40iw: Add missing NULL check for MPA private data
iw_cxgb4: Fix cxgb4 arm CQ logic w/IB_CQ_REPORT_MISSED_EVENTS
i40iw: Add missing check for interface already open
i40iw: Protect req_resource_num update
i40iw: Change mem_resources pointer to a u8
IB/core: Use memdup_user() rather than duplicating its implementation
IB/qib: Use memdup_user() rather than duplicating its implementation
iw_cxgb4: use the MPA initiator's IRD if < our ORD
iw_cxgb4: limit IRD/ORD advertised to ULP by device max.
IB/hfi1: Fix mm_struct use after free
IB/rdmvat: Fix double vfree() in rvt_create_qp() error path
IB/hfi1: Improve J_KEY generation
IB/hfi1: Return invalid field for non-QSFP CableInfo queries
...
projects / mirror_ubuntu-eoan-kernel.git / log