Add process_read_urb to usb_serial_driver so that a driver can rely on
the generic read (and throttle) mechanism but still do device specific
processing of incoming data (such as adding tty_flags before pushing to
line discipline).
The default generic implementation handles sysrq for consoles but
otherwise simply pushes to tty.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Johan Hovold [Wed, 17 Mar 2010 22:05:56 +0000 (23:05 +0100)]
USB: serial: clean up read processing in generic driver
Always process and flush read urb, but only resubmit when not throttled.
The new tty-layer supply plenty of slack so there is really no need to
cache and delay processing of a single urb while throttled.
Note that unthrottle now submits using GFP_KERNEL as we are not in
atomic context (so there is no need to save irq state either).
Note also that the process_read_urb function could be added to
usb_serial_driver should any driver need to do any device specific
processing.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Johan Hovold [Wed, 17 Mar 2010 22:05:54 +0000 (23:05 +0100)]
USB: serial: remove unnecessary re-initialisation of generic urbs
The generic read and write bulk urbs are initialised when allocated in
usb_serial_probe. The only field that needs to be updated after that is
the transfer_buffer_length of the write urb.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Johan Hovold [Wed, 17 Mar 2010 22:00:40 +0000 (23:00 +0100)]
USB: pl2303: increase the bulk-out buffer size to 256 byte
Increase the bulk-out buffer size from 64 to 256 byte.
This gives a significant increase in throughput already at 1Mbaud as well
as lowered CPU usage. The buffer is big enough to keep up also at 3Mbaud
(128b would not suffice).
Johan Hovold [Wed, 17 Mar 2010 22:00:37 +0000 (23:00 +0100)]
USB: serial: allow drivers to define bulk buffer sizes
Allow drivers to define custom bulk in/out buffer sizes in struct
usb_serial_driver. If not set, fall back to the default buffer size
which matches the endpoint size.
Three drivers are currently freeing the pre-allocated buffers and
allocating larger ones to achieve this at port probe (ftdi_sio) or even
at port open (ipaq and iuu_phoenix), which needless to say is suboptimal.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hans de Goede [Mon, 29 Mar 2010 10:03:17 +0000 (12:03 +0200)]
USB: Add a new quirk: USB_QUIRK_HONOR_BNUMINTERFACES
Add a new quirk USB_QUIRK_HONOR_BNUMINTERFACES, when this quirk is
set and a device has more interface descriptors in a configuration
then it claims to have in config->bNumInterfaces, ignore all additional
interfaces.
This is needed for devices which try to hide unused interfaces by only
lowering config->bNumInterfaces, and which can't handle if you try to talk
to the "hidden" interfaces.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jason Wessel [Tue, 16 Mar 2010 21:05:44 +0000 (16:05 -0500)]
usb-console: pass baud from console to the initial tty open
The usb console code has had a long standing problem of not being able
to pass the baud rate from the kernel argument console=ttyUSB0,BAUD
down to the initial tty open, unless you were willing to settle for
9600 baud.
The solution is to directly use tty_init_termios() in
usb_console_setup() as this will preserve any changes to the initial
termios setting on future opens.
CC: Alan Cox <alan@linux.intel.com> CC: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: f_mass_storage: dynamic buffers for better alignment
"Static" buffers in fsg_buffhd structure (ie. fields which are arrays
rather then pointers to dynamically allocated memory) are not aligned
to any "big" power of two which may lead to poor DMA performance
(copying "by hand" of head or tail) or no DMA at all even if otherwise
hardware supports it.
Therefore, this patch makes mass storage function use kmalloc()ed
buffers which are (because of their size) page aligned (which should
be enough for any hardware).
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Felipe Balbi [Fri, 12 Mar 2010 08:29:12 +0000 (10:29 +0200)]
usb: musb: gadget: support musb-specific test modes
we can support the musb-specific test modes on the
vendor specific range of test selector as stated
on USB Specification Table 9-7 Test Mode Selectors.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Felipe Balbi [Fri, 12 Mar 2010 08:29:06 +0000 (10:29 +0200)]
usb: musb: allow board to pass down fifo mode
boards might want to optimize their fifo configuration
to the particular needs of that specific board. Allow
that by moving all related data structures to
<linux/usb/musb.h>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Manuel Lauss [Mon, 8 Mar 2010 19:43:32 +0000 (20:43 +0100)]
USB: ehci-au1xxx does not need EHCI IO watchdog
I've been running variations of this patch for well over a year now;
my usual zoo of test devices didn't trigger any ill effects even
under heavy load. As a nice sideeffect idle-wakeups are reduced
from 20/s to about 2/s (EHCI hub with mouse and kbd).
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 5 Mar 2010 20:10:17 +0000 (15:10 -0500)]
USB: remove uses of URB_NO_SETUP_DMA_MAP
This patch (as1350) removes all usages of coherent buffers for USB
control-request setup-packet buffers. There's no good reason to
reserve coherent memory for these things; control requests are hardly
ever used in large quantity (the major exception is firmware
transfers, and they aren't time-critical). Furthermore, only seven
drivers used it. We might as well always use streaming DMA mappings
for setup-packet buffers, and remove some extra complexity from
usbcore.
The DMA-mapping portion of hcd.c is currently in flux. A separate
patch will be submitted to remove support for URB_NO_SETUP_DMA_MAP
after everything else settles down. The removal should go smoothly,
as by then nobody will be using it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 4 Mar 2010 22:05:08 +0000 (17:05 -0500)]
USB: straighten out port feature vs. port status usage
This patch (as1349b) clears up the confusion in many USB host
controller drivers between port features and port statuses. In mosty
cases it's true that the status bit is in the position given by the
corresponding feature value, but that's not always true and it's not
guaranteed in the USB spec.
There's no functional change, just replacing expressions of the form
(1 << USB_PORT_FEAT_x) with USB_PORT_STAT_x, which has the same value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 4 Mar 2010 16:32:30 +0000 (11:32 -0500)]
USB: remove bogus USB_PORT_FEAT_*_SPEED symbols
This patch (as1348) removes the bogus
USB_PORT_FEAT_{HIGHSPEED,SUPERSPEED} symbols from ch11.h. No such
features are defined by the USB spec. (There is a PORT_LOWSPEED
feature, but the spec doesn't mention it except to say that host
software should never use it.) The speed indicators are port
statuses, not port features.
As a temporary workaround for the xhci-hcd driver, a fictional
USB_PORT_STAT_SUPER_SPEED symbol is added.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ian Munsie [Wed, 3 Mar 2010 00:00:37 +0000 (11:00 +1100)]
USB: Remove large struct from the stack in USB storage isd200 driver
The compiler throws the following warning when compiling for a PowerPC 64
bit machine:
drivers/usb/storage/isd200.c:580: warning: the frame size of 2208 bytes is larger than 2048 bytes
There is a struct scsi_device which is placed on the stack and is
largely responsible for such wastage. The struct is just a dummy struct
filled with NULLs and set as the scsi_cmnd->device to make the
usb_stor_Bulk_transport function happy.
This patch makes the struct static, so that it is never placed onto the
stack and silences the compiler warning.
Signed-off-by: Ian Munsie <imunsie@au.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Eric Lescouet [Sat, 24 Apr 2010 21:38:17 +0000 (23:38 +0200)]
USB: split hub.h into ch11.h and merge-in hcd.h
Base on inputs from Alan Stern, split the hub.h header into:
- new ch11.h header (most of it) containing constants and
structures from chapter 11 of the USB 2.0 spec.
- a small remaining part being merged into hcd.h.
Signed-of-by: Eric Lescouet <eric@lescouet.org> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Eric Lescouet [Sat, 24 Apr 2010 21:34:27 +0000 (23:34 +0200)]
USB: make hub.h public (drivers dependency)
The usbcore headers: hcd.h and hub.h are shared between usbcore,
HCDs and a couple of other drivers (e.g. USBIP modules).
So, it makes sense to move them into a more public location and
to cleanup dependency of those modules on kernel internal headers.
This patch moves hub.h from drivers/usb/core into include/linux/usb/
Signed-of-by: Eric Lescouet <eric@lescouet.org> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Eric Lescouet [Sat, 24 Apr 2010 21:21:52 +0000 (23:21 +0200)]
USB: make hcd.h public (drivers dependency)
The usbcore headers: hcd.h and hub.h are shared between usbcore,
HCDs and a couple of other drivers (e.g. USBIP modules).
So, it makes sense to move them into a more public location and
to cleanup dependency of those modules on kernel internal headers.
This patch moves hcd.h from drivers/usb/core into include/linux/usb/
Signed-of-by: Eric Lescouet <eric@lescouet.org> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Tue, 18 May 2010 23:05:26 +0000 (16:05 -0700)]
USB: xhci: Fix check for room on the ring.
The length of the scatter gather list a driver can enqueue is limited by
the bus' sg_tablesize to 62 entries. Each entry will be described by at
least one transfer request block (TRB). If the entry's buffer crosses a
64KB boundary, then that entry will have to be described by two or more
TRBs. So even if the USB device driver respects sg_tablesize, the whole
scatter list may take more than 62 TRBs to describe, and won't fit on
the ring.
Don't assume that an empty ring means there is enough room on the
transfer ring. The old code would unconditionally queue this too-large
transfer, and over write the beginning of the transfer. This would mean
the cycle bit was unchanged in those overwritten transfers, causing the
hardware to think it didn't own the TRBs, and the host would seem to
hang.
Now drivers may see submit_urb() fail with -ENOMEM if the transfers are
too big to fit on the ring.
Sarah Sharp [Tue, 18 May 2010 23:05:21 +0000 (16:05 -0700)]
USB: xhci: Limit bus sg_tablesize to 62 TRBs.
When a scatter-gather list is enqueued to the xHCI driver, it translates
each entry into a transfer request block (TRB). Only 63 TRBs can be
used per ring segment, and there must be one additional TRB reserved to
make sure the hardware does not think the ring is empty (so the enqueue
pointer doesn't equal the dequeue pointer). Limit the bus sg_tablesize
to 62 TRBs.
Sarah Sharp [Thu, 6 May 2010 20:40:08 +0000 (13:40 -0700)]
USB: xhci: Fix issue with set interface after stall.
When the USB core installs a new interface, it unconditionally clears the
halts on all the endpoints on the new interface. Usually the xHCI host
needs to know when an endpoint is reset, so it can change its internal
endpoint state. In this case, it doesn't care, because the endpoints were
never halted in the first place.
To avoid issuing a redundant Reset Endpoint command, the xHCI driver looks
at xhci_virt_ep->stopped_td to determine if the endpoint was actually
halted. However, the functions that handle the stall never set that
variable to NULL after it dealt with the stall. So if an endpoint stalled
and a Reset Endpoint command completed, and then the class driver tried to
install a new alternate setting, the xHCI driver would access the old
xhci_virt_ep->stopped_td pointer. A similar problem occurs if the
endpoint has been stopped to cancel a transfer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
rtnetlink: make SR-IOV VF interface symmetric
sctp: delete active ICMP proto unreachable timer when free transport
tcp: fix MD5 (RFC2385) support
Linus Torvalds [Sun, 16 May 2010 18:11:31 +0000 (11:11 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Oprofile: Fix Loongson irq handler
MIPS: N32: Use compat version for sys_ppoll.
MIPS FPU emulator: allow Cause bits of FCSR to be writeable by ctc1
Wei Yongjun [Sun, 9 May 2010 16:56:07 +0000 (16:56 +0000)]
sctp: delete active ICMP proto unreachable timer when free transport
transport may be free before ICMP proto unreachable timer expire, so
we should delete active ICMP proto unreachable timer when transport
is going away.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 16 May 2010 07:34:04 +0000 (00:34 -0700)]
tcp: fix MD5 (RFC2385) support
TCP MD5 support uses percpu data for temporary storage. It currently
disables preemption so that same storage cannot be reclaimed by another
thread on same cpu.
We also have to make sure a softirq handler wont try to use also same
context. Various bug reports demonstrated corruptions.
Fix is to disable preemption and BH.
Reported-by: Bhaskar Dutta <bhaskie@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wu Zhangjin [Thu, 6 May 2010 16:59:46 +0000 (00:59 +0800)]
MIPS: Oprofile: Fix Loongson irq handler
The interrupt enable bit for the performance counters is in the Control
Register $24, not in the counter register.
loongson2_perfcount_handler(), we need to use
Shane McDonald [Fri, 7 May 2010 05:26:57 +0000 (23:26 -0600)]
MIPS FPU emulator: allow Cause bits of FCSR to be writeable by ctc1
In the FPU emulator code of the MIPS, the Cause bits of the FCSR register
are not currently writeable by the ctc1 instruction. In odd corner cases,
this can cause problems. For example, a case existed where a divide-by-zero
exception was generated by the FPU, and the signal handler attempted to
restore the FPU registers to their state before the exception occurred. In
this particular setup, writing the old value to the FCSR register would
cause another divide-by-zero exception to occur immediately. The solution
is to change the ctc1 instruction emulator code to allow the Cause bits of
the FCSR register to be writeable. This is the behaviour of the hardware
that the code is emulating.
This problem was found by Shane McDonald, but the credit for the fix goes
to Kevin Kissell. In Kevin's words:
I submit that the bug is indeed in that ctc_op: case of the emulator. The
Cause bits (17:12) are supposed to be writable by that instruction, but the
CTC1 emulation won't let them be updated by the instruction. I think that
actually if you just completely removed lines 387-388 [...] things would
work a good deal better. At least, it would be a more accurate emulation of
the architecturally defined FPU. If I wanted to be really, really pedantic
(which I sometimes do), I'd also protect the reserved bits that aren't
necessarily writable.
Signed-off-by: Shane McDonald <mcdonald.shane@gmail.com>
To: anemo@mba.ocn.ne.jp
To: kevink@paralogos.com
To: sshtylyov@mvista.com
Patchwork: http://patchwork.linux-mips.org/patch/1205/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
Nicolas Ferre [Sat, 15 May 2010 16:32:31 +0000 (12:32 -0400)]
mmc: at91_mci: modify cache flush routines
As we were using an internal dma flushing routine, this patch changes to
the DMA API flush_kernel_dcache_page(). Driver is able to compile now.
[akpm@linux-foundation.org: flush_kernel_dcache_page() comes before kunmap_atomic()] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 15 May 2010 16:03:15 +0000 (09:03 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
JFS: Free sbi memory in error path
fs/sysv: dereferencing ERR_PTR()
Fix double-free in logfs
Fix the regression created by "set S_DEAD on unlink()..." commit
Linus Torvalds [Sat, 15 May 2010 16:03:02 +0000 (09:03 -0700)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf record: Add a fallback to the reference relocation symbol
Jan Blunck [Mon, 12 Apr 2010 23:44:08 +0000 (16:44 -0700)]
JFS: Free sbi memory in error path
I spotted the missing kfree() while removing the BKL.
[akpm@linux-foundation.org: avoid multiple returns so it doesn't happen again] Signed-off-by: Jan Blunck <jblunck@suse.de> Cc: Dave Kleikamp <shaggy@austin.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Fri, 30 Apr 2010 21:17:09 +0000 (17:17 -0400)]
Fix the regression created by "set S_DEAD on unlink()..." commit
1) i_flags simply doesn't work for mount/unlink race prevention;
we may have many links to file and rm on one of those obviously
shouldn't prevent bind on top of another later on. To fix it
right way we need to mark _dentry_ as unsuitable for mounting
upon; new flag (DCACHE_CANT_MOUNT) is protected by d_flags and
i_mutex on the inode in question. Set it (with dont_mount(dentry))
in unlink/rmdir/etc., check (with cant_mount(dentry)) in places
in namespace.c that used to check for S_DEAD. Setting S_DEAD
is still needed in places where we used to set it (for directories
getting killed), since we rely on it for readdir/rmdir race
prevention.
2) rename()/mount() protection has another bogosity - we unhash
the target before we'd checked that it's not a mountpoint. Fixed.
3) ancient bogosity in pivot_root() - we locked i_mutex on the
right directory, but checked S_DEAD on the different (and wrong)
one. Noticed and fixed.
Linus Torvalds [Sat, 15 May 2010 04:28:42 +0000 (21:28 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6126/1: ARM mpcore_wdt: fix build failure and other fixes
ARM: 6125/1: ARM TWD: move TWD registers to common header
ARM: 6110/1: Fix Thumb-2 kernel builds when UACCESS_WITH_MEMCPY is enabled
ARM: 6112/1: Use the Inner Shareable I-cache and BTB ops on ARMv7 SMP
ARM: 6111/1: Implement read/write for ownership in the ARMv6 DMA cache ops
ARM: 6106/1: Implement copy_to_user_page() for noMMU
ARM: 6105/1: Fix the __arm_ioremap_caller() definition in nommu.c
Hugh Dickins [Sat, 15 May 2010 02:44:10 +0000 (19:44 -0700)]
profile: fix stats and data leakage
If the kernel is large or the profiling step small, /proc/profile
leaks data and readprofile shows silly stats, until readprofile -r
has reset the buffer: clear the prof_buffer when it is vmalloc()ed.
H. Peter Anvin [Fri, 14 May 2010 20:55:57 +0000 (13:55 -0700)]
x86, mrst: Don't blindly access extended config space
Do not blindly access extended configuration space unless we actively
know we're on a Moorestown platform. The fixed-size BAR capability
lives in the extended configuration space, and thus is not applicable
if the configuration space isn't appropriately sized.
This fixes booting certain VMware configurations with CONFIG_MRST=y.
Moorestown will add a fake PCI-X 266 capability to advertise the
presence of extended configuration space.
Reported-and-tested-by: Petr Vandrovec <petr@vandrovec.name> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Acked-by: Jacob Pan <jacob.jun.pan@intel.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <AANLkTiltKUa3TrKR1M51eGw8FLNoQJSLT0k0_K5X3-OJ@mail.gmail.com>
Linus Torvalds [Fri, 14 May 2010 19:20:09 +0000 (12:20 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, cacheinfo: Turn off L3 cache index disable feature in virtualized environments
x86, k8: Fix build error when K8_NB is disabled
x86, amd: Check X86_FEATURE_OSVW bit before accessing OSVW MSRs
x86: Fix fake apicid to node mapping for numa emulation
The L3 cache index disable feature of AMD CPUs has to be disabled if the
kernel is running as guest on top of a hypervisor because northbridge
devices are not available to the guest. Currently, this fixes a boot
crash on top of Xen. In the future this will become an issue on KVM as
well.
Check if northbridge devices are present and do not enable the feature
if there are none.
[ hpa: backported to 2.6.34 ]
Signed-off-by: Frank Arnold <frank.arnold@amd.com>
LKML-Reference: <1271945222-5283-3-git-send-email-bp@amd64.org> Acked-by: Borislav Petkov <borislav.petkov@amd.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: <stable@kernel.org>
K8_NB depends on PCI and when the last is disabled (allnoconfig) we fail
at the final linking stage due to missing exported num_k8_northbridges.
Add a header stub for that.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <20100503183036.GJ26107@aftab> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: <stable@kernel.org>
Linus Torvalds [Fri, 14 May 2010 18:49:42 +0000 (11:49 -0700)]
Merge branch 'for-linus' of git://git.infradead.org/users/eparis/notify
* 'for-linus' of git://git.infradead.org/users/eparis/notify:
inotify: don't leak user struct on inotify release
inotify: race use after free/double free in inotify inode marks
inotify: clean up the inotify_add_watch out path
Inotify: undefined reference to `anon_inode_getfd'
Manual merge to remove duplicate "select ANON_INODES" from Kconfig file
Sergei Shtylyov [Thu, 13 May 2010 18:51:51 +0000 (22:51 +0400)]
DA830: fix USB 2.0 clock entry
DA8xx OHCI driver fails to load due to failing clk_get() call for the USB 2.0
clock. Arrange matching USB 2.0 clock by the clock name instead of the device.
(Adding another CLK() entry for "ohci.0" device won't do -- in the future I'll
also have to enable USB 2.0 clock to configure CPPI 4.1 module, in which case
I won't have any device at all.)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Pavel Emelyanov [Wed, 12 May 2010 22:34:07 +0000 (15:34 -0700)]
inotify: don't leak user struct on inotify release
inotify_new_group() receives a get_uid-ed user_struct and saves the
reference on group->inotify_data.user. The problem is that free_uid() is
never called on it.
Issue seem to be introduced by 63c882a0 (inotify: reimplement inotify
using fsnotify) after 2.6.30.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Eric Paris <eparis@parisplace.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Eric Paris <eparis@redhat.com>
Eric Paris [Tue, 11 May 2010 21:17:40 +0000 (17:17 -0400)]
inotify: race use after free/double free in inotify inode marks
There is a race in the inotify add/rm watch code. A task can find and
remove a mark which doesn't have all of it's references. This can
result in a use after free/double free situation.
Task A Task B
------------ -----------
inotify_new_watch()
allocate a mark (refcnt == 1)
add it to the idr
inotify_rm_watch()
inotify_remove_from_idr()
fsnotify_put_mark()
refcnt hits 0, free
take reference because we are on idr
[at this point it is a use after free]
[time goes on]
refcnt may hit 0 again, double free
The fix is to take the reference BEFORE the object can be found in the
idr.
Signed-off-by: Eric Paris <eparis@redhat.com> Cc: <stable@kernel.org>
Linus Torvalds [Fri, 14 May 2010 14:29:29 +0000 (07:29 -0700)]
Merge branch 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze
* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Fix module loading on system with WB cache
microblaze: export assembly functions used by modules
microblaze: Remove powerpc code from Microblaze port
microblaze: Remove compilation warnings in cache macro
microblaze: export assembly functions used by modules
microblaze: fix get_user/put_user side-effects
microblaze: re-enable interrupts before calling schedule
Redirecting directly to lsm, here's the patch discussed on lkml:
http://lkml.org/lkml/2010/4/22/219
The mmap_min_addr value is useful information for an admin to see without
being root ("is my system vulnerable to kernel NULL pointer attacks?") and
its setting is trivially easy for an attacker to determine by calling
mmap() in PAGE_SIZE increments starting at 0, so trying to keep it private
has no value.
Only require CAP_SYS_RAWIO if changing the value, not reading it.
Comment from Serge :
Me, I like to write my passwords with light blue pen on dark blue
paper, pasted on my window - if you're going to get my password, you're
gonna get a headache.
Signed-off-by: Kees Cook <kees.cook@canonical.com> Acked-by: Serge Hallyn <serue@us.ibm.com> Signed-off-by: James Morris <jmorris@namei.org>
(cherry picked from commit 822cceec7248013821d655545ea45d1c6a9d15b3)
Linus Torvalds [Thu, 13 May 2010 21:36:19 +0000 (14:36 -0700)]
Merge branch 'kvm-updates/2.6.34' of git://git.kernel.org/pub/scm/virt/kvm/kvm
* 'kvm-updates/2.6.34' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Keep index within boundaries in kvmppc_44x_emul_tlbwe()
KVM: VMX: blocked-by-sti must not defer NMI injections
KVM: x86: Call vcpu_load and vcpu_put in cpuid_update
KVM: SVM: Fix wrong intercept masks on 32 bit
KVM: convert ioapic lock to spinlock
serial: imx.c: fix CTS trigger level lower to avoid lost chars
The imx CTS trigger level is left at its reset value that is 32
chars. Since the RX FIFO has 32 entries, when CTS is raised, the
FIFO already is full. However, some serial port devices first empty
their TX FIFO before stopping when CTS is raised, resulting in lost
chars.
This patch sets the trigger level lower so that other chars arrive
after CTS is raised, there is still room for 16 of them.
Alan Cox [Tue, 4 May 2010 19:42:36 +0000 (20:42 +0100)]
tty: Fix unbalanced BKL handling in error path
Arnd noted:
After the "retry_open:" label, we first get the tty_mutex
and then the BKL. However a the end of tty_open, we jump
back to retry_open with the BKL still held. If we run into
this case, the tty_open function will be left with the BKL
still held.
Jan Kara [Thu, 13 May 2010 10:52:57 +0000 (12:52 +0200)]
vfs: Fix O_NOFOLLOW behavior for paths with trailing slashes
According to specification
mkdir d; ln -s d a; open("a/", O_NOFOLLOW | O_RDONLY)
should return success but currently it returns ELOOP. This is a
regression caused by path lookup cleanup patch series.
Fix the code to ignore O_NOFOLLOW in case the provided path has trailing
slashes.
Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Reported-by: Marius Tolzmann <tolzmann@molgen.mpg.de> Acked-by: Miklos Szeredi <mszeredi@suse.cz> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 13 May 2010 14:35:26 +0000 (07:35 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ice1724 - Fix ESI Maya44 capture source control
ALSA: pcm - Use pgprot_noncached() for MIPS non-coherent archs
ALSA: virtuoso: fix Xonar D1/DX front panel microphone
ALSA: hda - Add hp-dv4 model for IDT 92HD71bx
ALSA: hda - Fix mute-LED GPIO pin for HP dv series
ALSA: hda: Fix 0 dB for Lenovo models using Conexant CX20549 (Venice)
projects / mirror_ubuntu-eoan-kernel.git / log