Matt Carlson [Thu, 3 Dec 2009 08:36:25 +0000 (08:36 +0000)]
tg3: Update version to 3.105
This patch updates the tg3 version to 3.105.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Thu, 3 Dec 2009 08:36:24 +0000 (08:36 +0000)]
tg3: Clean tg3_init_one()
Tg3's firmware is no longer loaded from tg3_init_one(). Remove the
error path that releases the firmware back to the system.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Thu, 3 Dec 2009 08:36:23 +0000 (08:36 +0000)]
tg3: Use pci_read_vpd() instead of private method
If the driver needs to use PCI configuration space to read the VPD data,
the accesses could collide with the pci_read_vpd() function. This patch
converts the driver to use pci_read_vpd() to avoid any potential
collisions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Thu, 3 Dec 2009 08:36:22 +0000 (08:36 +0000)]
tg3: Add some VPD preprocessor constants
This patch cleans up the VPD code by creating preprocessor definitions
and using them in the place of hardcoded constants.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Thu, 3 Dec 2009 08:36:21 +0000 (08:36 +0000)]
tg3: Add 57765 asic rev
This patch adds the 57765 asic revision.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Thu, 3 Dec 2009 08:36:20 +0000 (08:36 +0000)]
tg3: Make TSS enable independent of MSI-X enable
The 57765 asic rev has MSI-X capability, but does not support TSS. This
patch changes the tx paths so that TSS is explicitly mentioned, rather
than implied through the ENABLE_MSIX flag.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Thu, 3 Dec 2009 06:16:59 +0000 (06:16 +0000)]
be2net: Support for WoL using magic packet after suspend.
Add support for WOL using Magic Packet after suspend is done.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com> Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Thu, 3 Dec 2009 06:12:06 +0000 (06:12 +0000)]
be2net: Changes to print fw command opcode when command is failed by controller.
When a firmware command fails, only the failure codes are printed.
It is difficult to co-relate this to the actual command that has failed.
These changes will now print the command code that has failed.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com> Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This function walks the whole hashtable so there is no point in
passing it a network namespace. Instead I purge all timewait
sockets from dead network namespaces that I find. If the namespace
is one of the once I am trying to purge I am guaranteed no new timewait
sockets can be formed so this will get them all. If the namespace
is one I am not acting for it might form a few more but I will
call inet_twsk_purge again and shortly to get rid of them. In
any even if the network namespace is dead timewait sockets are
useless.
Move the calls of inet_twsk_purge into batch_exit routines so
that if I am killing a bunch of namespaces at once I will just
call inet_twsk_purge once and save a lot of redundant unnecessary
work.
My simple 4k network namespace exit test the cleanup time dropped from
roughly 8.2s to 1.6s. While the time spent running inet_twsk_purge fell
to about 2ms. 1ms for ipv4 and 1ms for ipv6.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
While we are looking up entries to free there is no reason to take
the lock in inet_twsk_purge. We have to drop locks and restart
occassionally anyway so adding a few more in case we get on the
wrong list because of a timewait move is no big deal. At the
same time not taking the lock for long periods of time is much
more polite to the rest of the users of the hash table.
In my test configuration of killing 4k network namespaces
this change causes 4k back to back runs of inet_twsk_purge on an
empty hash table to go from roughly 20.7s to 3.3s, and the total
time to destroy 4k network namespaces goes from roughly 44s to
3.3s.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the code so fib_rules_register always takes a template instead
of the actual fib_rules_ops structure that will be used. This is
required for network namespace support so 2 out of the 3 callers already
do this, it allows the error handling to be made common, and it allows
fib_rules_unregister to free the template for hte caller.
Modify fib_rules_unregister to use call_rcu instead of syncrhonize_rcu
to allw multiple namespaces to be cleaned up in the same rcu grace
period.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netns: Add an explicit rcu_barrier to unregister_pernet_{device|subsys}
This allows namespace exit methods to batch work that comes requires an
rcu barrier using call_rcu without having to treat the
unregister_pernet_operations cases specially.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Allow xfrm_user_net_exit to batch efficiently.
xfrm.nlsk is provided by the xfrm_user module and is access via rcu from
other parts of the xfrm code. Add xfrm.nlsk_stash a copy of xfrm.nlsk that
will never be set to NULL. This allows the synchronize_net and
netlink_kernel_release to be deferred until a whole batch of xfrm.nlsk sockets
have been set to NULL.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4: add sysctl to accept packets with local source addresses
Change fib_validate_source() to accept packets with a local source address when
the "accept_local" sysctl is set for the incoming inet device. Combined with the
previous patches, this allows to communicate between multiple local interfaces
over the wire.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Allow to delete the local rule and recreate it with a higher priority. This
can be used to force packets with a local destination out on the wire instead
of routing them to loopback. Additionally this patch allows to recreate rules
with a priority of 0.
Combined with the previous patch to allow oif classification, a socket can
be bound to the desired interface and packets routed to the wire like this:
# move local rule to lower priority
ip rule add pref 1000 lookup local
ip rule del pref 0
# route packets of sockets bound to eth0 to the wire independant
# of the destination address
ip rule add pref 100 oif eth0 lookup 100
ip route add default dev eth0 table 100
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
The ifname member is only used to resolve interface names and is not needed
during rule lookups. The target and ctarget members however are used during
rule lookups and are currently located in a second cacheline.
Move ifname further to the end to make sure both target and ctarget are
located in the same cacheline as other members used during rule lookups.
Mikulas Patocka [Thu, 3 Dec 2009 06:26:38 +0000 (22:26 -0800)]
sunhme: fix dma warning in Sun HME
Fix dma-api-checking warnings in Sun HME
Sun HME driver is mapping the first fragment with dma_map_single and subsequent
fragments with dma_map_page. It is unmapping all fragments with dma_unmap_single
and that produces the warning.
This patch changes it so that it unmaps only the first fragment with
dma_unmap_single and subsequent fragments are unmapped with dma_unmap_page.
Ilpo Järvinen [Thu, 3 Dec 2009 06:24:02 +0000 (22:24 -0800)]
tcp: clear hints to avoid a stale one (nfs only affected?)
Eric Dumazet mentioned in a context of another problem:
"Well, it seems NFS reuses its socket, so maybe we miss some
cleaning as spotted in this old patch"
I've not check under which conditions that actually happens but
if true, we need to make sure we don't accidently leave stale
hints behind when the write queue had to be purged (whether reusing
with NFS can actually happen if purging took place is something I'm
not sure of).
...At least it compiles.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Take advantage of the fact that an explicit rtnl_kill_links is
unnecessary (and skipping it improves batching), as network namespace
exit calls dellink on all remaining virtual devices, and
rtnl_link_unregister calls dellink on all outstanding devices in that
network namespace. To do this we need to leave the vlan proc
directories in place until after network device exit time, which is
done by using register_pernet_subsys instead of
register_pernet_device.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This is a significantly revised implementation of an earlier (year-old)
patch that no longer applies cleanly, with permission of the original
author (Adam Langley):
This is a significantly revised implementation of an earlier (year-old)
patch that no longer applies cleanly, with permission of the original
author (Adam Langley):
TCPCT part 1e: implement socket option TCP_COOKIE_TRANSACTIONS
Provide per socket control of the TCP cookie option and SYN/SYNACK data.
This is a straightforward re-implementation of an earlier (year-old)
patch that no longer applies cleanly, with permission of the original
author (Adam Langley):
TCPCT part 1d: define TCP cookie option, extend existing struct's
Data structures are carefully composed to require minimal additions.
For example, the struct tcp_options_received cookie_plus variable fits
between existing 16-bit and 8-bit variables, requiring no additional
space (taking alignment into consideration). There are no additions to
tcp_request_sock, and only 1 pointer in tcp_sock.
This is a significantly revised implementation of an earlier (year-old)
patch that no longer applies cleanly, with permission of the original
author (Adam Langley):
The principle difference is using a TCP option to carry the cookie nonce,
instead of a user configured offset in the data. This is more flexible and
less subject to user configuration error. Such a cookie option has been
suggested for many years, and is also useful without SYN data, allowing
several related concepts to use the same extension option.
"Re: SYN floods (was: does history repeat itself?)", September 9, 1996.
http://www.merit.net/mail.archives/nanog/1996-09/msg00235.html
"Re: what a new TCP header might look like", May 12, 1998.
ftp://ftp.isi.edu/end2end/end2end-interest-1998.mail
These functions will also be used in subsequent patches that implement
additional features.
Requires:
TCPCT part 1a: add request_values parameter for sending SYNACK
TCPCT part 1b: generate Responder Cookie secret
TCPCT part 1c: sysctl_tcp_cookie_size, socket option TCP_COOKIE_TRANSACTIONS
Signed-off-by: William.Allen.Simpson@gmail.com Signed-off-by: David S. Miller <davem@davemloft.net>
TCPCT part 1c: sysctl_tcp_cookie_size, socket option TCP_COOKIE_TRANSACTIONS
Define sysctl (tcp_cookie_size) to turn on and off the cookie option
default globally, instead of a compiled configuration option.
Define per socket option (TCP_COOKIE_TRANSACTIONS) for setting constant
data values, retrieving variable cookie values, and other facilities.
Move inline tcp_clear_options() unchanged from net/tcp.h to linux/tcp.h,
near its corresponding struct tcp_options_received (prior to changes).
This is a straightforward re-implementation of an earlier (year-old)
patch that no longer applies cleanly, with permission of the original
author (Adam Langley):
TCPCT part 1a: add request_values parameter for sending SYNACK
Add optional function parameters associated with sending SYNACK.
These parameters are not needed after sending SYNACK, and are not
used for retransmission. Avoids extending struct tcp_request_sock,
and avoids allocating kernel memory.
Also affects DCCP as it uses common struct request_sock_ops,
but this parameter is currently reserved for future use.
Signed-off-by: William.Allen.Simpson@gmail.com Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Handle few corner cases in firmware hang detection and recovery:
o Don't mark device state as READY, till handshake with
firmware is done.
o During probe, if start_firmware fails, restore reference
count.
o Don't increment refernce count, if start_firmware fails
during firmware reset.
o Clear __NX_RESETTING bit, incase of fatal error or tempeature
reaches critical limit so that pci remove() doesn't poll on
this bit.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Narender Kumar [Wed, 2 Dec 2009 15:46:18 +0000 (15:46 +0000)]
netxen : fix debug tools access for NX2031
Driver maps only some part of the MMIO bar 0 in case of
NX2031. This is sufficient for tx and rx by the driver.
When debug tools need to access resources in
unmapped regions, driver needs to map these on the fly
in order to complete read/write request.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com> Signed-off-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 2 Dec 2009 17:03:18 +0000 (17:03 +0000)]
e1000e: correct ICH/PCH PHY operations function pointers
Some function pointers for a few PHY operations (for 82578 and 82567) and
were set incorrectly causing functions to be executed that were accessing
incorrect PHY register offsets for that particular device. This patch also
moves a few PHY-specific functions from ich8lan.c to the more appropriate
phy.c.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 2 Dec 2009 17:02:43 +0000 (17:02 +0000)]
e1000e: refactor PHY ID detection workaround
The workaround that detects the correct PHY ID when an initial read of the
PHY ID registers returns an invalid one should retry up to ten times with
a small delay between attempts using a single PHY address and then repeat
using the remaining possible PHY addresses. Do this instead of trying each
possible PHY address repeating that up to 100 times.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 2 Dec 2009 17:02:14 +0000 (17:02 +0000)]
e1000e: check_polarity function pointers not set for 8257x
The function pointers for 8257x devices are not set. This is not really a
problem now because there is nothing in the driver that references the
pointers for this particular MAC-family (the appropriate functions are
called directly), but the pointers should be set in case they are used in
the future.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 2 Dec 2009 16:49:02 +0000 (16:49 +0000)]
skbuff: remove skb_dma_map/unmap
The two functions skb_dma_map/unmap are unsafe to use as they cause
problems when packets are cloned and sent to multiple devices while a HW
IOMMU is enabled. Due to this it is best to remove the code so it is not
used by any other network driver maintainters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 2 Dec 2009 16:48:38 +0000 (16:48 +0000)]
tg3: remove use of skb_dma_map/unmap
Due to the fact that skb_dma_map/unmap do not work correctly when a HW
IOMMU is enabled it has been recommended to go about removing the calls
from the network device drivers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> CC: Matt Carlson <mcarlson@broadcom.com> CC: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 2 Dec 2009 16:48:18 +0000 (16:48 +0000)]
be2net: remove use of skb_dma_map/unmap
Due to the fact that skb_dma_map/unmap do not work correctly when a HW
IOMMU is enabled it has been recommended to go about removing the calls
from the network device drivers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> CC: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 2 Dec 2009 16:47:57 +0000 (16:47 +0000)]
bnx2: remove skb_dma_map/unmap calls from driver
Due to the fact that skb_dma_map/unmap do not work correctly when a HW
IOMMU is enabled it has been recommended to go about removing the calls
from the network device drivers.
[ Fix bnx2_free_tx_skbs() ring indexing and use NETDEV_TX_OK return
code in bnx2_start_xmit() after cleaning up DMA mapping errors. -Mchan ]
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 2 Dec 2009 16:47:37 +0000 (16:47 +0000)]
igbvf: remove skb_dma_map/unmap call from drivers
This patch removes the skb_dma_map/unmap calls from the igbvf driver due to
the fact that it does not play well with HW IOMMU when combined with
transmitting cloned skbs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 2 Dec 2009 16:47:18 +0000 (16:47 +0000)]
igb: remove use of skb_dma_map from driver
This change removes skb_dma_map/unmap calls from the igb driver due to the
fact that the call is incompatible with iommu enabled kernels. In order to
prevent warnings about using the wrong unmap call I have added a
mapped_as_page value to the buffer_info structure to track if the mapped
region is a page or a buffer.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 2 Dec 2009 16:46:56 +0000 (16:46 +0000)]
ixgbe: remove skb_dma_map/unmap calls from driver
This patch removes skb_dma_map/unmap calls from the ixgbe driver due to the
fact that the calls don't work with HW IOMMU enabled systems. The problem
is that multiple mappings will give different results when HW IOMMU is
enabled and the skb_dma_map/unmap calls only have one location to store
mappings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 2 Dec 2009 16:46:31 +0000 (16:46 +0000)]
ixgb: remove use of skb_dma_map from ixgb
skb_dma_map is incompatible with HW iommu due to the fact that multiple
mappings can result in different results each time. For this reason it is
best to just remove use of these function calls.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 2 Dec 2009 16:46:00 +0000 (16:46 +0000)]
e1000: remove use of skb_dma_map from e1000 driver
Remove the use of skb_dma_map from the e1000 driver in order to avoid
issues when HW iommu are in use.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 2 Dec 2009 16:45:31 +0000 (16:45 +0000)]
e1000e: remove use of skb_dma_map from e1000e driver
In testing we have found that skb_dma_map/unmap is incompatible with HW
IOMMU due to the fact that multiple mappings will return different results.
In order to correct this we need to remove skb_dma_map/unmap calls from the
e1000e driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shan Wei [Wed, 2 Dec 2009 23:39:04 +0000 (15:39 -0800)]
ip: update the description of rp_filter in ip-sysctl.txt
The commit 27fed4175acf81ddd91d9a4ee2fd298981f60295 (ip: fix logic of
reverse path filter sysctl) has changed the logic of rp_filter. The
document about rp_filter is out of date. Now, setting
conf/all/rp_filte with 0 can also enable source validation.
Update the document according to the commit.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Breno Leitao [Thu, 26 Nov 2009 07:31:49 +0000 (07:31 +0000)]
bnx2: EEH is failing with timeout
bnx2 is failing when a PCI error is detected. The error is the
following:
bnx2: Chip not in correct endian mode
bnx2: fw sync timeout, reset code = 404001d
This error was caused because the way pci_restore_state() is working
after commit 4b77b0a2ba27d64f58f16d8d4d48d8319dda36ff ("PCI: Clear
saved_state after the state has been restored").
Signed-off-by: Breno Leitao<leitao@linux.vnet.ibm.com> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: compat_sys_recvmmsg user timespec arg can be NULL
We must test if user timespec is non-NULL before copying from userpace,
same as sys_recvmmsg().
Commiter note: changed it so that we have just one branch.
Signed-off-by: Jean-Mickael Guerin <jean-mickael.guerin@6wind.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Both to traverse the entries and to set the msg_len field.
Commiter note: folded two patches and avoided one branch repeating the
compat test.
Signed-off-by: Jean-Mickael Guerin <jean-mickael.guerin@6wind.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warning, when building on 64 bits:
net/sctp/socket.c:2091: warning: large integer implicitly
truncated to unsigned type
Signed-off-by: Andrei Pelinescu-Onciul <andrei@iptel.org> Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hideyuki Sasaki [Tue, 1 Dec 2009 12:15:58 +0000 (12:15 +0000)]
net/ps3: Add support for gelic link negotiation
Add ethtool_ops.set_settings support to the PS3 gelic network driver.
Allows manual setting of ethernet link speed.
Signed-off-by: Hideyuki Sasaki <xhide@rd.scei.sony.co.jp> Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Geoff Levand [Tue, 1 Dec 2009 12:15:53 +0000 (12:15 +0000)]
net/ps3: Cleanup gelic enums
Cleanup of the gelic driver enumerations:
o Add some missing commas.
o Add an Ether port post fix (PS3 currently only supports PORT_0).
o Add a new enum gelic_lv1_phy to use when interacting with the PHY.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Sun, 29 Nov 2009 17:57:46 +0000 (17:57 +0000)]
be2net: fix unnecessary access to hardware to get link, port info
Every time while doing ethtool->get_settings we are accessing
the hardware to get link status and port information.
This is not necessary. We now use the cached copy for this info
and update it when the link status changes.
From: Suresh R <sureshr@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Yang [Tue, 1 Dec 2009 17:18:34 +0000 (17:18 +0000)]
atl1e:disable NETIF_F_TSO6 for hardware limit
For hardware limit to support TSOV6, just disable this feature Signed-off-by: Jie Yang <jie.yang@atheros.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin [Tue, 1 Dec 2009 15:54:24 +0000 (15:54 +0000)]
e1000e: Use sizeof struct rather than pointer in e1000_get_eeprom()
Don't use the sizeof the pointer to clear the result
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Tue, 1 Dec 2009 15:53:48 +0000 (15:53 +0000)]
e1000e: PHY type cleanups in e1000e_check_downshift()
Remove the case for 82577 because it does not support the ability to check
for downshift. Add case for e1000_phy_bm which can do this.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Tue, 1 Dec 2009 15:53:07 +0000 (15:53 +0000)]
e1000e: add debug messages
Add some helpful debug messages.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Tue, 1 Dec 2009 15:51:11 +0000 (15:51 +0000)]
e1000e: comment corrections
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Tue, 1 Dec 2009 15:50:31 +0000 (15:50 +0000)]
e1000e: enable new 82567V-3 device
This new PCI device ID is for a new combination of MAC and PHY both of
which already have supporting code in the driver, just not yet in this
combination. During validation of the device, an intermittent issue was
discovered with waking it from a suspended state which can be resolved with
the pre-existing workaround to disable gigabit speed prior to suspending.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Tue, 1 Dec 2009 15:49:51 +0000 (15:49 +0000)]
e1000e: ensure the link state is correct for serdes links
This patch ensures that the link state (as reported in
mac->serdes_has_link) will transition to false when autoneg fails to
complete but valid codewords were detected.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Tue, 1 Dec 2009 15:47:22 +0000 (15:47 +0000)]
e1000e: provide family-specific PHY power up/down operations
The different families (80003es2lan, 8257x, ICHx/PCH) supported by the
driver each have their own conditions when the PHY can be powered down.
This patch rewrites the PHY power up/down code to fit with the family-
specific style used in the driver. All pre-existing calls to power up or
down the PHY remain untouched. A new call to power down the PHY when
removing the driver when the interface is down replaces the current call
to reset the PHY in order to reduce power consumption.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Tue, 1 Dec 2009 15:47:02 +0000 (15:47 +0000)]
e1000e: guard against buffer overflow in cable length tables
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Tue, 1 Dec 2009 15:46:43 +0000 (15:46 +0000)]
e1000e: provide family-specific functions to manage VLAN filter arrays
The two MAC-families that have VLAN filter table register arrays manage
each a bit differently from one another, so provide family-specific
functions for managing the register arrays and function pointers to access
the appropriate function. Also make sure attempts to access these
register arrays are not done on parts not supporting that feature.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: remove [un]register_pernet_gen_... and update the docs.
No that all of the callers have been updated to set fields in
struct pernet_operations, and simplified to let the network
namespace core handle the allocation and freeing of the storage
for them, remove the surpurpflous methods and update the docs
to the new style.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-kernels.git / log