Vadim Pasternak [Tue, 12 Mar 2019 08:40:41 +0000 (08:40 +0000)]
mlxsw: core: Prevent duplication during QSFP module initialization
Verify during thermal initialization if QSFP module's entry is already
configured in order to prevent duplication.
Such scenario could happen in case two switch drivers (PCI and I2C
based) coexist and if after boot, splitting configuration is applied
for some ports and then I2C based driver is re-probed.
In such case after reboot same QSFP module, associated with split will
be discovered by I2C based driver few times, and it will cause a crash.
It could happen for example on system equipped with BMC (Baseboard
Management Controller), running I2C based driver, when the next steps
are performed:
- System boot
- Host side configures port spilt.
- BMC side is rebooted.
Fixes: 6a79507cfe94 ("mlxsw: core: Extend thermal module with per QSFP module thermal zones") Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kangjie Lu [Tue, 12 Mar 2019 07:43:18 +0000 (02:43 -0500)]
net: sh_eth: fix a missing check of of_get_phy_mode
of_get_phy_mode may fail and return a negative error code;
the fix checks the return value of of_get_phy_mode and
returns NULL of it fails.
Fixes: b356e978e92f ("sh_eth: add device tree support") Signed-off-by: Kangjie Lu <kjlu@umn.edu> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net>
For -stable v5.0:
('net/mlx5e: Fix access to non-existing receive queue')
('net/mlx5e: Properly get the PF number phys port name ndo')
('net/mlx5: Fix multiple updates of steering rules in parallel')
('net/mlx5: Avoid panic when setting vport mac, getting vport config')
('net/mlx5: Avoid panic when setting vport rate')
('net/mlx5e: IPoIB, Fix RX checksum statistics update')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patchset contains Netfilter fixes for your net tree:
1) Fix list corruption in device notifier in the masquerade
infrastructure, from Florian Westphal.
2) Fix double-free of sets and use-after-free when deleting elements.
3) Don't bogusly return EBUSY when removing a set after flush command.
4) Use-after-free in dynamically allocate operations.
5) Don't report a new ruleset generation to userspace if transaction
list is empty, this invalidates the userspace cache innecessarily.
From Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 95d6ebd53c79 ("net/x25: fix use-after-free in x25_device_event()") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: andrew hendry <andrew.hendry@gmail.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Paasch [Mon, 11 Mar 2019 18:41:05 +0000 (11:41 -0700)]
tcp: Don't access TCP_SKB_CB before initializing it
Since commit eeea10b83a13 ("tcp: add
tcp_v4_fill_cb()/tcp_v4_restore_cb()"), tcp_vX_fill_cb is only called
after tcp_filter(). That means, TCP_SKB_CB(skb)->end_seq still points to
the IP-part of the cb.
We thus should not mock with it, as this can trigger bugs (thanks
syzkaller):
[ 12.349396] ==================================================================
[ 12.350188] BUG: KASAN: slab-out-of-bounds in ip6_datagram_recv_specific_ctl+0x19b3/0x1a20
[ 12.351035] Read of size 1 at addr ffff88006adbc208 by task test_ip6_datagr/1799
Setting end_seq is actually no more necessary in tcp_filter as it gets
initialized later on in tcp_vX_fill_cb.
Cc: Eric Dumazet <edumazet@google.com> Fixes: eeea10b83a13 ("tcp: add tcp_v4_fill_cb()/tcp_v4_restore_cb()") Signed-off-by: Christoph Paasch <cpaasch@apple.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bryan Whitehead [Mon, 11 Mar 2019 17:39:39 +0000 (13:39 -0400)]
lan743x: Fix RX Kernel Panic
It has been noticed that running the speed test at
www.speedtest.net occasionally causes a kernel panic.
Investigation revealed that under this test RX buffer allocation
sometimes fails and returns NULL. But the lan743x driver did
not handle this case.
This patch fixes this issue by attempting to allocate a buffer
before sending the new rx packet to the OS. If the allocation
fails then the new rx packet is dropped and the existing buffer
is reused in the DMA ring.
Updates for v2:
Additional 2 locations where allocation was not checked,
has been changed to reuse existing buffer.
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver") Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: nf_tables: return immediately on empty commit
When running 'nft flush ruleset' while no rules exist, we will increment
the generation counter and announce a new genid to userspace, yet
nothing had changed in the first place.
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Tariq Toukan [Tue, 5 Mar 2019 14:45:09 +0000 (16:45 +0200)]
net/mlx5e: Fix access to non-existing receive queue
In case number of channels is changed while interface is down,
RSS indirection table is mistakenly not modified accordingly,
causing access to out-of-range non-existing object.
Fix by updating the RSS indireciton table also in the early
return flow of interface down.
Fixes: fb35c534b788 ("net/mlx5e: Fix NULL pointer derefernce in set channels error flow") Fixes: bbeb53b8b2c9 ("net/mlx5e: Move RSS params to a dedicated struct") Reported-by: Or Gerlitz <ogerlitz@mellanox.com> Tested-by: Maria Pasechnik <mariap@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Roi Dayan [Tue, 26 Feb 2019 14:18:19 +0000 (16:18 +0200)]
net/mlx5e: Properly get the PF number phys port name ndo
Currently, we fail to retrieve the PF number in some cases (e.g
single ported cards, lag capability), this further results in a
call trace issued by the rtnetlink code, since the error value
is not -EOPNOTSUPP. Change the implementation to be independent
from the lag code and function properly on both two ports and
single ported cards.
Fixes: c12ecc230564 ("net/mlx5e: Move to use common phys port names for vport representors") Signed-off-by: Roi Dayan <roid@mellanox.com> Acked-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eli Britstein [Tue, 8 Jan 2019 10:15:37 +0000 (12:15 +0200)]
net/mlx5: Consolidate update FTE for all removal changes
With commit a18e879d4e45 ("net/mlx5e: Annul encap action ordering
requirement") and a use-case of e-switch remote mirroring, the
incremental/stepped FTE removal process done by the fs core got us to
illegal transient states and FW errors:
SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad
parameter(0x3), syndrome (0x9c2e40)
To avoid that and improve FTE removal performance, aggregate the FTE's
updates that should be applied. Remove the FTE if it is empty, or apply
one FW update command with the aggregated updates.
Fixes: a18e879d4e45 ("net/mlx5e: Annul encap action ordering requirement") Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eli Britstein [Thu, 31 Jan 2019 12:38:32 +0000 (14:38 +0200)]
net/mlx5: Add a locked flag to node removal functions
Add a locked flag to the node removal functions to signal if the
parent is already locked from the caller function or not as a pre-step
towards outside lock. Currently always use false with no functional
change.
Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eli Britstein [Thu, 31 Jan 2019 12:56:01 +0000 (14:56 +0200)]
net/mlx5: Fix multiple updates of steering rules in parallel
There might be a condition where the fte found is not active yet. In
this case we should not use it, but continue to search for another, or
allocate a new one.
Fixes: bd71b08ec2ee ("net/mlx5: Support multiple updates of steering rules in parallel") Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Arnd Bergmann [Mon, 11 Mar 2019 15:38:17 +0000 (16:38 +0100)]
y2038: fix socket.h header inclusion
Referencing the __kernel_long_t type caused some user space applications
to stop compiling when they had not already included linux/posix_types.h,
e.g.
s/multicast.c -o ext/sockets/multicast.lo
In file included from /builddir/build/BUILD/php-7.3.3/main/php.h:468,
from /builddir/build/BUILD/php-7.3.3/ext/sockets/sockets.c:27:
/builddir/build/BUILD/php-7.3.3/ext/sockets/sockets.c: In function 'zm_startup_sockets':
/builddir/build/BUILD/php-7.3.3/ext/sockets/sockets.c:776:40: error: '__kernel_long_t' undeclared (first use in this function)
776 | REGISTER_LONG_CONSTANT("SO_SNDTIMEO", SO_SNDTIMEO, CONST_CS | CONST_PERSISTENT);
It is safe to include that header here, since it only contains kernel
internal types that do not conflict with other user space types.
It's still possible that some related build failures remain, but those
are likely to be for code that is not already y2038 safe.
Reported-by: Laura Abbott <labbott@redhat.com> Fixes: a9beb86ae6e5 ("sock: Add SO_RCVTIMEO_NEW and SO_SNDTIMEO_NEW") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch says there are three functions which free expr->ops.
Fixes: b8e204006340 ("netfilter: nft_compat: use .release_ops and remove list of extension") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nf_tables: bogus EBUSY when deleting set after flush
Set deletion after flush coming in the same batch results in EBUSY. Add
set use counter to track the number of references to this set from
rules. We cannot rely on the list of bindings for this since such list
is still populated from the preparation phase.
Reported-by: Václav Zindulka <vaclav.zindulka@tlapnet.cz> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fixes: c9e6bc644e55 ("net: add gro_cells infrastructure") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 10 Mar 2019 17:36:40 +0000 (10:36 -0700)]
vxlan: test dev->flags & IFF_UP before calling gro_cells_receive()
Same reasons than the ones explained in commit 4179cb5a4c92
("vxlan: test dev->flags & IFF_UP before calling netif_rx()")
netif_rx() or gro_cells_receive() must be called under a strict contract.
At device dismantle phase, core networking clears IFF_UP
and flush_all_backlogs() is called after rcu grace period
to make sure no incoming packet might be in a cpu backlog
and still referencing the device.
A similar protocol is used for gro_cells infrastructure, as
gro_cells_destroy() will be called only after a full rcu
grace period is observed after IFF_UP has been cleared.
Most drivers call netif_rx() from their interrupt handler,
and since the interrupts are disabled at device dismantle,
netif_rx() does not have to check dev->flags & IFF_UP
Virtual drivers do not have this guarantee, and must
therefore make the check themselves.
Otherwise we risk use-after-free and/or crashes.
Fixes: d342894c5d2f ("vxlan: virtual extensible lan") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 10 Mar 2019 16:07:14 +0000 (09:07 -0700)]
net/x25: fix use-after-free in x25_device_event()
In case of failure x25_connect() does a x25_neigh_put(x25->neighbour)
but forgets to clear x25->neighbour pointer, thus triggering use-after-free.
Since the socket is visible in x25_list, we need to hold x25_list_lock
to protect the operation.
syzbot report :
BUG: KASAN: use-after-free in x25_kill_by_device net/x25/af_x25.c:217 [inline]
BUG: KASAN: use-after-free in x25_device_event+0x296/0x2b0 net/x25/af_x25.c:252
Read of size 8 at addr ffff8880a030edd0 by task syz-executor003/7854
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot+04babcefcd396fabec37@syzkaller.appspotmail.com Cc: andrew hendry <andrew.hendry@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shiju Jose [Sun, 10 Mar 2019 06:47:51 +0000 (14:47 +0800)]
net: hns3: fix to stop multiple HNS reset due to the AER changes
The commit bfcb79fca19d
("PCI/ERR: Run error recovery callbacks for all affected devices")
affected the non-fatal error recovery logic for the HNS and RDMA devices.
This is because each HNS PF under PCIe bus receive callbacks
from the AER driver when an error is reported for one of the PF.
This causes unwanted PF resets because
the HNS decides which PF to reset based on the reset type set.
The HNS error handling code sets the reset type based on the hw error
type detected.
This patch provides fix for the above issue for the recovery of
the hw errors in the HNS and RDMA devices.
This patch needs backporting to the kernel v5.0+
Fixes: 332fbf576579 ("net: hns3: add handling of hw ras errors using new set of commands") Reported-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: Shiju Jose <shiju.jose@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 9 Mar 2019 22:43:38 +0000 (14:43 -0800)]
ip: fix ip_mc_may_pull() return value
ip_mc_may_pull() must return 0 if there is a problem, not an errno.
syzbot reported :
BUG: KASAN: use-after-free in br_ip4_multicast_igmp3_report net/bridge/br_multicast.c:947 [inline]
BUG: KASAN: use-after-free in br_multicast_ipv4_rcv net/bridge/br_multicast.c:1631 [inline]
BUG: KASAN: use-after-free in br_multicast_rcv+0x3cd8/0x4440 net/bridge/br_multicast.c:1741
Read of size 4 at addr ffff88820a4084ee by task syz-executor.2/11183
Fixes: ba5ea614622d ("bridge: simplify ip_mc_check_igmp() and ipv6_mc_check_mld() calls") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Sat, 9 Mar 2019 09:26:53 +0000 (10:26 +0100)]
net: keep refcount warning in reqsk_free()
As Eric Dumazet said, "We do not have a way to tell if the req was ever
inserted in a hash table, so better play safe.".
Let's remove this comment, so that nobody will be tempted to drop the
WARN_ON_ONCE() line.
Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: stmmac: Avoid one more sometimes uninitialized Clang warning
When building with -Wsometimes-uninitialized, Clang warns:
drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c:111:2: error: variable
'ns' is used uninitialized whenever 'if' condition is false
[-Werror,-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c:111:2: error: variable
'ns' is used uninitialized whenever '&&' condition is false
[-Werror,-Wsometimes-uninitialized]
Clang is concerned with the use of stmmac_do_void_callback (which
stmmac_get_systime wraps), as it may fail to initialize these values if
the if condition was ever false (meaning the callback doesn't exist).
It's not wrong because the callback is what initializes ns. While it's
unlikely that the callback is going to disappear at some point and make
that condition false, we can easily avoid this warning by zero
initializing the variable.
Link: https://github.com/ClangBuiltLinux/linux/issues/384 Fixes: df103170854e ("net: stmmac: Avoid sometimes uninitialized Clang warnings") Suggested-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Fri, 8 Mar 2019 00:21:27 +0000 (01:21 +0100)]
net: dsa: mv88e6xxx: Set correct interface mode for CPU/DSA ports
By default, the switch driver is expected to configure CPU and DSA
ports to their maximum speed. For the 6341 and 6390 families, the
ports interface mode has to be configured as well. The 6390X range
support 10G ports using XAUI, while the 6341 and 6390 supports
2500BaseX, as their maximum speed.
Fixes: 787799a9d555 ("net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseX") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Sat, 9 Mar 2019 00:29:58 +0000 (00:29 +0000)]
rxrpc: Fix client call queueing, waiting for channel
rxrpc_get_client_conn() adds a new call to the front of the waiting_calls
queue if the connection it's going to use already exists. This is bad as
it allows calls to get starved out.
Fix this by adding to the tail instead.
Also change the other enqueue point in the same function to put it on the
front (ie. when we have a new connection). This makes the point that in
the case of a new connection the new call goes at the front (though it
doesn't actually matter since the queue should be unoccupied).
Fixes: 45025bceef17 ("rxrpc: Improve management and caching of client connection objects") Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a crash in AF_XDP's xsk_diag_put_ring() which was passing
wrong queue argument, from Eric.
2) Fix a regression due to wrong test for TCP GSO packets used in
various BPF helpers like NAT64, from Willem.
3) Fix a sk_msg strparser warning which asserts that strparser must
be stopped first, from Jakub.
4) Fix rejection of invalid options/bind flags in AF_XDP, from Björn.
5) Fix GSO in bpf_lwt_push_ip_encap() which must properly set inner
headers and inner protocol, from Peter.
6) Fix a libbpf leak when kernel does not support BTF, from Nikita.
7) Various BPF selftest and libbpf build fixes to make out-of-tree
compilation work and to properly resolve dependencies via fixdep
target, from Stanislav.
8) Fix rejection of invalid ldimm64 imm field, from Daniel.
9) Fix bpf stats sysctl compile warning of unused helper function
proc_dointvec_minmax_bpf_stats() under some configs, from Arnd.
10) Fix couple of warnings about using plain integer as NULL, from Bo.
11) Fix some BPF sample spelling mistakes, from Colin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Fri, 8 Mar 2019 21:09:47 +0000 (22:09 +0100)]
tcp: handle inet_csk_reqsk_queue_add() failures
Commit 7716682cc58e ("tcp/dccp: fix another race at listener
dismantle") let inet_csk_reqsk_queue_add() fail, and adjusted
{tcp,dccp}_check_req() accordingly. However, TFO and syncookies
weren't modified, thus leaking allocated resources on error.
Contrary to tcp_check_req(), in both syncookies and TFO cases,
we need to drop the request socket. Also, since the child socket is
created with inet_csk_clone_lock(), we have to unlock it and drop an
extra reference (->sk_refcount is initially set to 2 and
inet_csk_reqsk_queue_add() drops only one ref).
For TFO, we also need to revert the work done by tcp_try_fastopen()
(with reqsk_fastopen_remove()).
Fixes: 7716682cc58e ("tcp/dccp: fix another race at listener dismantle") Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ethernet: sun: Zero initialize class in default case in niu_add_ethtool_tcam_entry
When building with -Wsometimes-uninitialized, Clang warns:
drivers/net/ethernet/sun/niu.c:7466:5: warning: variable 'class' is used
uninitialized whenever switch default is taken
[-Wsometimes-uninitialized]
The default case can never happen because i can only be 0 to 3
(NIU_L3_PROG_CLS is defined as 4). To make this clear to Clang,
just zero initialize class in the default case (use the macro
CLASS_CODE_UNRECOG to make it clear this shouldn't happen).
Link: https://github.com/ClangBuiltLinux/linux/issues/403 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 26fc181e6cac ("fou, fou6: do not assume linear skbs") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Stefano Brivio <sbrivio@redhat.com> Cc: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Buslov [Wed, 6 Mar 2019 15:50:43 +0000 (17:50 +0200)]
net: sched: fix potential use-after-free in __tcf_chain_put()
When used with unlocked classifier that have filters attached to actions
with goto chain, __tcf_chain_put() for last non action reference can race
with calls to same function from action cleanup code that releases last
action reference. In this case action cleanup handler could free the chain
if it executes after all references to chain were released, but before all
concurrent users finished using it. Modify __tcf_chain_put() to only access
tcf_chain fields when holding block->lock. Remove local variables that were
used to cache some tcf_chain fields and are no longer needed because their
values can now be obtained directly from chain under block->lock
protection.
Fixes: 726d061286ce ("net: sched: prevent insertion of new classifiers during chain flush") Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Wed, 6 Mar 2019 11:05:49 +0000 (12:05 +0100)]
vhost: silence an unused-variable warning
On some architectures, the MMU can be disabled, leading to access_ok()
becoming an empty macro that does not evaluate its size argument,
which in turn produces an unused-variable warning:
Adalbert Lazăr [Wed, 6 Mar 2019 10:13:53 +0000 (12:13 +0200)]
vsock/virtio: fix kernel panic from virtio_transport_reset_no_sock
Previous to commit 22b5c0b63f32 ("vsock/virtio: fix kernel panic
after device hot-unplug"), vsock_core_init() was called from
virtio_vsock_probe(). Now, virtio_transport_reset_no_sock() can be called
before vsock_core_init() has the chance to run.
[Wed Feb 27 14:17:09 2019] BUG: unable to handle kernel NULL pointer dereference at 0000000000000110
[Wed Feb 27 14:17:09 2019] #PF error: [normal kernel read fault]
[Wed Feb 27 14:17:09 2019] PGD 0 P4D 0
[Wed Feb 27 14:17:09 2019] Oops: 0000 [#1] SMP PTI
[Wed Feb 27 14:17:09 2019] CPU: 3 PID: 59 Comm: kworker/3:1 Not tainted 5.0.0-rc7-390-generic-hvi #390
[Wed Feb 27 14:17:09 2019] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
[Wed Feb 27 14:17:09 2019] Workqueue: virtio_vsock virtio_transport_rx_work [vmw_vsock_virtio_transport]
[Wed Feb 27 14:17:09 2019] RIP: 0010:virtio_transport_reset_no_sock+0x8c/0xc0 [vmw_vsock_virtio_transport_common]
[Wed Feb 27 14:17:09 2019] Code: 35 8b 4f 14 48 8b 57 08 31 f6 44 8b 4f 10 44 8b 07 48 8d 7d c8 e8 84 f8 ff ff 48 85 c0 48 89 c3 74 2a e8 f7 31 03 00 48 89 df <48> 8b 80 10 01 00 00 e8 68 fb 69 ed 48 8b 75 f0 65 48 33 34 25 28
[Wed Feb 27 14:17:09 2019] RSP: 0018:ffffb42701ab7d40 EFLAGS: 00010282
[Wed Feb 27 14:17:09 2019] RAX: 0000000000000000 RBX: ffff9d79637ee080 RCX: 0000000000000003
[Wed Feb 27 14:17:09 2019] RDX: 0000000000000001 RSI: 0000000000000002 RDI: ffff9d79637ee080
[Wed Feb 27 14:17:09 2019] RBP: ffffb42701ab7d78 R08: ffff9d796fae70e0 R09: ffff9d796f403500
[Wed Feb 27 14:17:09 2019] R10: ffffb42701ab7d90 R11: 0000000000000000 R12: ffff9d7969d09240
[Wed Feb 27 14:17:09 2019] R13: ffff9d79624e6840 R14: ffff9d7969d09318 R15: ffff9d796d48ff80
[Wed Feb 27 14:17:09 2019] FS: 0000000000000000(0000) GS:ffff9d796fac0000(0000) knlGS:0000000000000000
[Wed Feb 27 14:17:09 2019] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[Wed Feb 27 14:17:09 2019] CR2: 0000000000000110 CR3: 0000000427f22000 CR4: 00000000000006e0
[Wed Feb 27 14:17:09 2019] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[Wed Feb 27 14:17:09 2019] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[Wed Feb 27 14:17:09 2019] Call Trace:
[Wed Feb 27 14:17:09 2019] virtio_transport_recv_pkt+0x63/0x820 [vmw_vsock_virtio_transport_common]
[Wed Feb 27 14:17:09 2019] ? kfree+0x17e/0x190
[Wed Feb 27 14:17:09 2019] ? detach_buf_split+0x145/0x160
[Wed Feb 27 14:17:09 2019] ? __switch_to_asm+0x40/0x70
[Wed Feb 27 14:17:09 2019] virtio_transport_rx_work+0xa0/0x106 [vmw_vsock_virtio_transport]
[Wed Feb 27 14:17:09 2019] NET: Registered protocol family 40
[Wed Feb 27 14:17:09 2019] process_one_work+0x167/0x410
[Wed Feb 27 14:17:09 2019] worker_thread+0x4d/0x460
[Wed Feb 27 14:17:09 2019] kthread+0x105/0x140
[Wed Feb 27 14:17:09 2019] ? rescuer_thread+0x360/0x360
[Wed Feb 27 14:17:09 2019] ? kthread_destroy_worker+0x50/0x50
[Wed Feb 27 14:17:09 2019] ret_from_fork+0x35/0x40
[Wed Feb 27 14:17:09 2019] Modules linked in: vmw_vsock_virtio_transport vmw_vsock_virtio_transport_common input_leds vsock serio_raw i2c_piix4 mac_hid qemu_fw_cfg autofs4 cirrus ttm drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops virtio_net psmouse drm net_failover pata_acpi virtio_blk failover floppy
Fixes: 22b5c0b63f32 ("vsock/virtio: fix kernel panic after device hot-unplug") Reported-by: Alexandru Herghelegiu <aherghelegiu@bitdefender.com> Signed-off-by: Adalbert Lazăr <alazar@bitdefender.com> Co-developed-by: Stefan Hajnoczi <stefanha@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Wed, 6 Mar 2019 06:46:27 +0000 (14:46 +0800)]
connector: fix unsafe usage of ->real_parent
proc_exit_connector() uses ->real_parent lockless. This is not
safe that its parent can go away at any moment, so use RCU to
protect it, and ensure that this task is not released.
Fixes: b086ff87251b4a4 ("connector: add parent pid and tgid to coredump and exit events") Signed-off-by: Zhang Yu <zhangyu31@baidu.com> Signed-off-by: Li RongQing <lirongqing@baidu.com> Acked-by: Evgeniy Polyakov <zbr@ioremap.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Wed, 6 Mar 2019 03:26:37 +0000 (11:26 +0800)]
net: hns3: add dma_rmb() for rx description
HW can not guarantee complete write desc->rx.size, even though
HNS3_RXD_VLD_B has been set. Driver needs to add dma_rmb()
instruction to make sure desc->rx.size is always valid.
Fixes: e55970950556 ("net: hns3: Add handling of GRO Pkts not fully RX'ed in NAPI poll") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pedro Tammela [Tue, 5 Mar 2019 14:35:54 +0000 (11:35 -0300)]
net: add missing documentation in linux/skbuff.h
This patch adds missing documentation for some inline functions on
linux/skbuff.h. The patch is incomplete and a lot more can be added,
just wondering if it's of interest of the netdev developers.
Also fixed some whitespaces.
Signed-off-by: Pedro Tammela <pctammela@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bo YU [Fri, 8 Mar 2019 06:45:51 +0000 (01:45 -0500)]
bpf: fix warning about using plain integer as NULL
Sparse warning below:
sudo make C=2 CF=-D__CHECK_ENDIAN__ M=net/bpf/
CHECK net/bpf//test_run.c
net/bpf//test_run.c:19:77: warning: Using plain integer as NULL pointer
./include/linux/bpf-cgroup.h:295:77: warning: Using plain integer as NULL pointer
Fixes: 8bad74f9840f ("bpf: extend cgroup bpf core to allow multiple cgroup storage types") Acked-by: Yonghong Song <yhs@fb.com> Signed-off-by: Bo YU <tsu.yubo@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Björn Töpel [Fri, 8 Mar 2019 07:57:27 +0000 (08:57 +0100)]
xsk: fix to reject invalid options in Tx descriptor
Passing a non-existing option in the options member of struct
xdp_desc was, incorrectly, silently ignored. This patch addresses
that behavior, and drops any Tx descriptor with non-existing options.
We have examined existing user space code, and to our best knowledge,
no one is relying on the current incorrect behavior. AF_XDP is still
in its infancy, so from our perspective, the risk of breakage is very
low, and addressing this problem now is important.
Fixes: 35fcde7f8deb ("xsk: support for Tx") Signed-off-by: Björn Töpel <bjorn.topel@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Björn Töpel [Fri, 8 Mar 2019 07:57:26 +0000 (08:57 +0100)]
xsk: fix to reject invalid flags in xsk_bind
Passing a non-existing flag in the sxdp_flags member of struct
sockaddr_xdp was, incorrectly, silently ignored. This patch addresses
that behavior, and rejects any non-existing flags.
We have examined existing user space code, and to our best knowledge,
no one is relying on the current incorrect behavior. AF_XDP is still
in its infancy, so from our perspective, the risk of breakage is very
low, and addressing this problem now is important.
Fixes: 965a99098443 ("xsk: add support for bind for Rx") Signed-off-by: Björn Töpel <bjorn.topel@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
bpf, libbpf: fixing leak when kernel does not support btf
We could end up in situation when we have object file w/ all btf
info, but kernel does not support btf yet. In this situation
currently libbpf just set obj->btf to NULL w/o freeing it first.
This patch is fixing it by making sure to run btf__free first.
Fixes: d29d87f7e612 ("btf: separate btf creation and loading") Signed-off-by: Nikita V. Shirokov <tehnerd@tehnerd.com> Acked-by: Yonghong Song <yhs@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
David S. Miller [Fri, 8 Mar 2019 19:48:20 +0000 (11:48 -0800)]
Merge branch 'stmmac-add-some-fixes-for-stm32'
Christophe Roullier says:
====================
stmmac: add some fixes for stm32
For common stmmac:
- Add support to set CSR Clock range selection in DT
For stm32mpu:
- Glue codes to support magic packet
- Glue codes to support all PHY config :
PHY_MODE (MII,GMII, RMII, RGMII) and in normal,
PHY wo crystal (25Mhz),
PHY wo crystal (50Mhz), No 125Mhz from PHY config
For stm32mcu:
- Add Ethernet support for stm32h7
Changes in V3:
- Reverse for syscfg management because it is manage by these patches
https://lkml.org/lkml/2018/12/12/133
https://lkml.org/lkml/2018/12/12/134
https://lkml.org/lkml/2018/12/12/131
https://lkml.org/lkml/2018/12/12/132
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: ethernet: stmmac: add management of clk_csr property
In Documentation stmmac.txt there is possibility to
fixed CSR Clock range selection with property clk_csr.
This patch add the management of this property
For example to use it, add in your ethernet node DT:
clk_csr = <3>;
Signed-off-by: Christophe Roullier <christophe.roullier@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add properties to support all Phy config
PHY_MODE (MII,GMII, RMII, RGMII) and in normal, PHY wo crystal (25Mhz),
PHY wo crystal (50Mhz), No 125Mhz from PHY config.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ethernet: stmmac: update to support all PHY config for stm32mp157c.
Update glue codes to support all PHY config on stm32mp157c
PHY_MODE (MII,GMII, RMII, RGMII) and in normal, PHY wo crystal (25Mhz),
PHY wo crystal (50Mhz), No 125Mhz from PHY config.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
sctp: process the error returned from sctp_sock_migrate()
This patchset is to process the errs returned by sctp_auth_init_hmacs()
and sctp_bind_addr_dup() from sctp_sock_migrate(). And also fix a panic
caused by new ep->auth_hmacs was not set due to net->sctp.auth_enable
changed by sysctl before accepting an assoc.
====================
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 3 Mar 2019 09:54:55 +0000 (17:54 +0800)]
sctp: call sctp_auth_init_hmacs() in sctp_sock_migrate()
New ep's auth_hmacs should be set if old ep's is set, in case that
net->sctp.auth_enable has been changed to 0 by users and new ep's
auth_hmacs couldn't be set in sctp_endpoint_init().
It can even crash kernel by doing:
1. on server: sysctl -w net.sctp.auth_enable=1,
sysctl -w net.sctp.addip_enable=1,
sysctl -w net.sctp.addip_noauth_enable=0,
listen() on server,
sysctl -w net.sctp.auth_enable=0.
2. on client: connect() to server.
3. on server: accept() the asoc,
sysctl -w net.sctp.auth_enable=1.
4. on client: send() asconf packet to server.
It's because the old ep->auth_hmacs wasn't copied to the new ep while
ep->auth_hmacs is used in sctp_auth_calculate_hmac() when processing
the incoming auth chunks, and it should have been done when migrating
sock.
Reported-by: Ying Xu <yinxu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 3 Mar 2019 09:54:54 +0000 (17:54 +0800)]
sctp: move up sctp_auth_init_hmacs() in sctp_endpoint_init()
sctp_auth_init_hmacs() is called only when ep->auth_enable is set.
It better to move up sctp_auth_init_hmacs() and remove auth_enable
check in it and check auth_enable only once in sctp_endpoint_init().
Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Brivio [Fri, 8 Mar 2019 15:40:57 +0000 (16:40 +0100)]
vxlan: Fix GRO cells race condition between receive and link delete
If we receive a packet while deleting a VXLAN device, there's a chance
vxlan_rcv() is called at the same time as vxlan_dellink(). This is fine,
except that vxlan_dellink() should never ever touch stuff that's still in
use, such as the GRO cells list.
Otherwise, vxlan_rcv() crashes while queueing packets via
gro_cells_receive().
Move the gro_cells_destroy() to vxlan_uninit(), which runs after the RCU
grace period is elapsed and nothing needs the gro_cells anymore.
This is now done in the same way as commit 8e816df87997 ("geneve: Use GRO
cells infrastructure.") originally implemented for GENEVE.
Reported-by: Jianlin Shi <jishi@redhat.com> Fixes: 58ce31cca1ff ("vxlan: GRO support at tunnel layer") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Fri, 8 Mar 2019 12:48:39 +0000 (12:48 +0000)]
rxrpc: Fix client call connect/disconnect race
rxrpc_disconnect_client_call() reads the call's connection ID protocol
value (call->cid) as part of that function's variable declarations. This
is bad because it's not inside the locked section and so may race with
someone granting use of the channel to the call.
This manifests as an assertion failure (see below) where the call in the
presumed channel (0 because call->cid wasn't set when we read it) doesn't
match the call attached to the channel we were actually granted (if 1, 2 or
3).
Fix this by moving the read and dependent calculations inside of the
channel_lock section. Also, only set the channel number and pointer
variables if cid is not zero (ie. unset).
This problem can be induced by injecting an occasional error in
rxrpc_wait_for_channel() before the call to schedule().
Make two further changes also:
(1) Add a trace for wait failure in rxrpc_connect_call().
(2) Drop channel_lock before BUG'ing in the case of the assertion failure.
Fixes: 45025bceef17 ("rxrpc: Improve management and caching of client connection objects") Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Fri, 8 Mar 2019 07:49:16 +0000 (15:49 +0800)]
sctp: remove sched init from sctp_stream_init
syzbot reported a NULL-ptr deref caused by that sched->init() in
sctp_stream_init() set stream->rr_next = NULL.
kasan: GPF could be caused by NULL-ptr deref or user memory access
RIP: 0010:sctp_sched_rr_dequeue+0xd3/0x170 net/sctp/stream_sched_rr.c:141
Call Trace:
sctp_outq_dequeue_data net/sctp/outqueue.c:90 [inline]
sctp_outq_flush_data net/sctp/outqueue.c:1079 [inline]
sctp_outq_flush+0xba2/0x2790 net/sctp/outqueue.c:1205
All sched info is saved in sout->ext now, in sctp_stream_init()
sctp_stream_alloc_out() will not change it, there's no need to
call sched->init() again, since sctp_outq_init() has already
done it.
Fixes: 5bbbbe32a431 ("sctp: introduce stream scheduler foundations") Reported-by: syzbot+4c9934f20522c0efd657@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Fri, 8 Mar 2019 06:50:54 +0000 (14:50 +0800)]
route: set the deleted fnhe fnhe_daddr to 0 in ip_del_fnhe to fix a race
The race occurs in __mkroute_output() when 2 threads lookup a dst:
CPU A CPU B
find_exception()
find_exception() [fnhe expires]
ip_del_fnhe() [fnhe is deleted]
rt_bind_exception()
In rt_bind_exception() it will bind a deleted fnhe with the new dst, and
this dst will get no chance to be freed. It causes a dev defcnt leak and
consecutive dmesg warnings:
unregister_netdevice: waiting for ethX to become free. Usage count = 1
Especially thanks Jon to identify the issue.
This patch fixes it by setting fnhe_daddr to 0 in ip_del_fnhe() to stop
binding the deleted fnhe with a new dst when checking fnhe's fnhe_daddr
and daddr in rt_bind_exception().
It works as both ip_del_fnhe() and rt_bind_exception() are protected by
fnhe_lock and the fhne is freed by kfree_rcu().
Fixes: deed49df7390 ("route: check and remove route cache when we get route") Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: nf_tables: fix set double-free in abort path
The abort path can cause a double-free of an anonymous set.
Added-and-to-be-aborted rule looks like this:
udp dport { 137, 138 } drop
The to-be-aborted transaction list looks like this:
newset
newsetelem
newsetelem
rule
This gets walked in reverse order, so first pass disables the rule, the
set elements, then the set.
After synchronize_rcu(), we then destroy those in same order: rule, set
element, set element, newset.
Problem is that the anonymous set has already been bound to the rule, so
the rule (lookup expression destructor) already frees the set, when then
cause use-after-free when trying to delete the elements from this set,
then try to free the set again when handling the newset expression.
Rule releases the bound set in first place from the abort path, this
causes the use-after-free on set element removal when undoing the new
element transactions. To handle this, skip new element transaction if
set is bound from the abort path.
This is still causes the use-after-free on set element removal. To
handle this, remove transaction from the list when the set is already
bound.
Joint work with Florian Westphal.
Fixes: f6ac85858976 ("netfilter: nf_tables: unbind set in rule from commit path")
Bugzilla: https://bugzilla.netfilter.org/show_bug.cgi?id=1325 Acked-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fixes: f421436a591d ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Arvid Brodin <arvid.brodin@alten.se> Signed-off-by: David S. Miller <davem@davemloft.net>
The simple vNIC mailbox length should be 12 decimal and not 0x12.
Using a decimal also makes it clear this is a length value and not
another field within the simple mailbox defines.
Found by code inspection, there are no known firmware configurations
where this would cause issues.
Fixes: 527d7d1b9949 ("nfp: read mailbox address from TLV caps") Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: atm: Add another IS_ENABLED(CONFIG_COMPAT) in atm_dev_ioctl
I removed compat's universal assignment to 0, which allows this if
statement to fall through when compat is passed with a value other
than 0.
Fixes: f9d19a7494e5 ("net: atm: Use IS_ENABLED in atm_dev_ioctl") Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: stmmac: Avoid sometimes uninitialized Clang warnings
When building with -Wsometimes-uninitialized, Clang warns:
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:495:3: warning: variable 'ns' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:495:3: warning: variable 'ns' is used uninitialized whenever '&&' condition is false [-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:532:3: warning: variable 'ns' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:532:3: warning: variable 'ns' is used uninitialized whenever '&&' condition is false [-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:741:3: warning: variable 'sec_inc' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:741:3: warning: variable 'sec_inc' is used uninitialized whenever '&&' condition is false [-Wsometimes-uninitialized]
Clang is concerned with the use of stmmac_do_void_callback (which
stmmac_get_timestamp and stmmac_config_sub_second_increment wrap),
as it may fail to initialize these values if the if condition was ever
false (meaning the callbacks don't exist). It's not wrong because the
callbacks (get_timestamp and config_sub_second_increment respectively)
are the ones that initialize the variables. While it's unlikely that the
callbacks are ever going to disappear and make that condition false, we
can easily avoid this warning by zero initialize the variables.
Link: https://github.com/ClangBuiltLinux/linux/issues/384 Suggested-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When building with -Wsometimes-uninitialized, Clang warns:
net/atm/resources.c:256:6: warning: variable 'number' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
net/atm/resources.c:212:7: warning: variable 'iobuf_len' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
Clang won't realize that compat is 0 when CONFIG_COMPAT is not set until
the constant folding stage, which happens after this semantic analysis.
Use IS_ENABLED instead so that the zero is present at the semantic
analysis stage, which eliminates this warning.
qede: Fix internal loopback failure with jumbo mtu configuration
Driver uses port-mtu as packet-size for the loopback traffic. This patch
limits the max packet size to 1.5K to avoid data being split over multiple
buffer descriptors (BDs) in cases where MTU > PAGE_SIZE.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 7 Mar 2019 15:52:24 +0000 (16:52 +0100)]
enic: fix build warning without CONFIG_CPUMASK_OFFSTACK
The enic driver relies on the CONFIG_CPUMASK_OFFSTACK feature to
dynamically allocate a struct member, but this is normally intended for
local variables.
Building with clang, I get a warning for a few locations that check the
address of the cpumask_var_t:
drivers/net/ethernet/cisco/enic/enic_main.c:122:22: error: address of array 'enic->msix[i].affinity_mask' will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]
As far as I can tell, the code is still correct, as the truth value of
the pointer is what we need in this configuration. To get rid of
the warning, use cpumask_available() instead of checking the
pointer directly.
Fixes: 322cf7e3a4e8 ("enic: assign affinity hint to interrupts") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 7 Mar 2019 10:31:55 +0000 (11:31 +0100)]
peak_usb: fix clang build warning
Clang points out undefined behavior when building the pcan_usb_pro driver:
drivers/net/can/usb/peak_usb/pcan_usb_pro.c:136:15: error: passing an object that undergoes default argument promotion to 'va_start' has undefined behavior [-Werror,-Wvarargs]
Changing the function prototype to avoid argument promotion in the
varargs call avoids the warning, and should make this well-defined.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Masaru Nagai [Thu, 7 Mar 2019 10:24:47 +0000 (11:24 +0100)]
ravb: Decrease TxFIFO depth of Q3 and Q2 to one
Hardware has the CBS (Credit Based Shaper) which affects only Q3
and Q2. When updating the CBS settings, even if the driver does so
after waiting for Tx DMA finished, there is a possibility that frame
data still remains in TxFIFO.
To avoid this, decrease TxFIFO depth of Q3 and Q2 to one.
This patch has been exercised this using netperf TCP_MAERTS, TCP_STREAM
and UDP_STREAM tests run on an Ebisu board. No performance change was
detected, outside of noise in the tests, both in terms of throughput and
CPU utilisation.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper") Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com> Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[simon: updated changelog] Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 7 Mar 2019 09:32:07 +0000 (10:32 +0100)]
isdn: isdnloop: fix pointer dereference bug
clang has spotted an ancient code bug and warns about it with:
drivers/isdn/isdnloop/isdnloop.c:573:12: error: address of array 'card->rcard' will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]
This is an array of pointers, so we should check if a specific
pointer exists in the array before using it, not whether the
array itself exists.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 7 Mar 2019 09:31:20 +0000 (10:31 +0100)]
davinci_emac: always build in CONFIG_OF code
clang warns about what seems to be an unintended use of an obscure C
language feature where a forward declaration of an array remains usable
when the final definition is never seen:
drivers/net/ethernet/ti/davinci_emac.c:1694:34: error: tentative array definition assumed to have one element [-Werror]
static const struct of_device_id davinci_emac_of_match[];
There is no harm in always enabling the device tree matching code here,
and it makes the code behave in a more conventional way aside from
avoiding the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Mon, 4 Mar 2019 20:08:53 +0000 (21:08 +0100)]
bpf: fix replace_map_fd_with_map_ptr's ldimm64 second imm field
Non-zero imm value in the second part of the ldimm64 instruction for
BPF_PSEUDO_MAP_FD is invalid, and thus must be rejected. The map fd
only ever sits in the first instructions' imm field. None of the BPF
loaders known to us are using it, so risk of regression is minimal.
For clarity and consistency, the few insn->{src_reg,imm} occurrences
are rewritten into insn[0].{src_reg,imm}. Add a test case to the BPF
selftest suite as well.
Fixes: 0246e64d9a5f ("bpf: handle pseudo BPF_LD_IMM64 insn") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Song Liu <songliubraving@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Jakub Sitnicki [Thu, 7 Mar 2019 10:35:43 +0000 (11:35 +0100)]
bpf: Stop the psock parser before canceling its work
We might have never enabled (started) the psock's parser, in which case it
will not get stopped when destroying the psock. This leads to a warning
when trying to cancel parser's work from psock's deferred destructor:
Stop psock's parser just before canceling its work.
Fixes: 1d79895aef18 ("sk_msg: Always cancel strp work before freeing the psock") Reported-by: kernel test robot <rong.a.chen@intel.com> Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
selftests: bpf: test_progs: initialize duration in singal_pending test
CHECK macro implicitly uses duration. We call CHECK() a couple of times
before duration is initialized from bpf_prog_test_run().
Explicitly set duration to 0 to avoid compiler warnings.
Fixes: 740f8a657221 ("selftests/bpf: make sure signal interrupts BPF_PROG_TEST_RUN") Signed-off-by: Stanislav Fomichev <sdf@google.com> Acked-by: Yonghong Song <yhs@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
libbpf: force fixdep compilation at the start of the build
libbpf targets don't explicitly depend on fixdep target, so when
we do 'make -j$(nproc)', there is a high probability, that some
objects will be built before fixdep binary is available.
Fix this by running sub-make; this makes sure that fixdep dependency
is properly accounted for.
For the same issue in perf, see commit abb26210a395 ("perf tools: Force
fixdep compilation at the start of the build").
Auto-detecting system features:
... libelf: [ on ]
... bpf: [ on ]
HOSTCC /tmp/bld/fixdep.o
CC /tmp/bld/libbpf.o
CC /tmp/bld/bpf.o
CC /tmp/bld/btf.o
CC /tmp/bld/nlattr.o
CC /tmp/bld/libbpf_errno.o
CC /tmp/bld/str_error.o
CC /tmp/bld/netlink.o
CC /tmp/bld/bpf_prog_linfo.o
CC /tmp/bld/libbpf_probes.o
CC /tmp/bld/xsk.o
HOSTLD /tmp/bld/fixdep-in.o
LINK /tmp/bld/fixdep
LD /tmp/bld/libbpf-in.o
LINK /tmp/bld/libbpf.a
LINK /tmp/bld/libbpf.so
LINK /tmp/bld/test_libbpf
$ head /tmp/bld/.libbpf.o.cmd
# cannot find fixdep (/usr/local/google/home/sdf/src/linux/xxx//fixdep)
# using basic dep data
Auto-detecting system features:
... libelf: [ on ]
... bpf: [ on ]
HOSTCC /tmp/bld/fixdep.o
HOSTLD /tmp/bld/fixdep-in.o
LINK /tmp/bld/fixdep
CC /tmp/bld/libbpf.o
CC /tmp/bld/bpf.o
CC /tmp/bld/nlattr.o
CC /tmp/bld/btf.o
CC /tmp/bld/libbpf_errno.o
CC /tmp/bld/str_error.o
CC /tmp/bld/netlink.o
CC /tmp/bld/bpf_prog_linfo.o
CC /tmp/bld/libbpf_probes.o
CC /tmp/bld/xsk.o
LD /tmp/bld/libbpf-in.o
LINK /tmp/bld/libbpf.a
LINK /tmp/bld/libbpf.so
LINK /tmp/bld/test_libbpf
Fixes: 7c422f557266 ("tools build: Build fixdep helper from perf and basic libs") Reported-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Stanislav Fomichev <sdf@google.com> Acked-by: Yonghong Song <yhs@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
selftests: bpf: fix compilation with out-of-tree $(OUTPUT)
A bunch of related changes lumped together:
* Create prog_tests and verifier output directories; these don't exist with
out-of-tree $(OUTPUT)
* Add missing -I (via separate TEST_{PROGS,VERIFIER}_CFLAGS) for the main tree
($(PWD) != $(OUTPUT) for out-of-tree)
* Add libbpf.a dependency for test_progs_32 (parallel make fails otherwise)
* Add missing "; \" after "cd" when generating test.h headers
Tested by:
$ alias m="make -s -j$(nproc)"
$ m -C tools/testing/selftests/bpf/ clean
$ m -C tools/lib/bpf/ clean
$ rm -rf xxx; mkdir xxx; m -C tools/testing/selftests/bpf/ OUTPUT=$PWD/xxx
$ m -C tools/testing/selftests/bpf/
Fixes: 3f30658830f3 ("selftests: bpf: break up test_progs - preparations") Fixes: 2dfb40121ee8 ("selftests: bpf: prepare for break up of verifier tests") Fixes: 3ef84346c561 ("selftests: bpf: makefile support sub-register code-gen test mode") Signed-off-by: Stanislav Fomichev <sdf@google.com> Acked-by: Yonghong Song <yhs@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Peter Oskolkov [Tue, 5 Mar 2019 00:27:09 +0000 (16:27 -0800)]
selftests/bpf: test that GSO works in lwt_ip_encap
Add a test on egress that a large TCP packet successfully goes through
the lwt+bpf encap tunnel.
Although there is no direct evidence that GSO worked, as opposed to
e.g. TCP segmentation or IP fragmentation (maybe a kernel stats counter
should be added to track the number of failed GSO attempts?), without
the previous patch in the patchset this test fails, and printk-debugging
showed that software-based GSO succeeded here (veth is not compatible with
SKB_GSO_DODGY, so GSO happens in the software stack).
Also removed an unnecessary nodad and added a missed failed flag.
Signed-off-by: Peter Oskolkov <posk@google.com> Acked-by: Song Liu <songliubraving@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Peter Oskolkov [Tue, 5 Mar 2019 00:27:08 +0000 (16:27 -0800)]
net: fix GSO in bpf_lwt_push_ip_encap
GSO needs inner headers and inner protocol set properly to work.
skb->inner_mac_header: skb_reset_inner_headers() assigns the current
mac header value to inner_mac_header; but it is not set at the point,
so we need to call skb_reset_inner_mac_header, otherwise gre_gso_segment
fails: it does
int tnl_hlen = skb_inner_mac_header(skb) - skb_transport_header(skb);
...
if (unlikely(!pskb_may_pull(skb, tnl_hlen)))
...
skb->inner_protocol should also be correctly set.
Fixes: ca78801a81e0 ("bpf: handle GSO in bpf_lwt_push_encap") Signed-off-by: Peter Oskolkov <posk@google.com> Reviewed-by: David Ahern <dsahern@gmail.com> Acked-by: Song Liu <songliubraving@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Fixes: a36b38aa2af6 ("xsk: add sock_diag interface for AF_XDP") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Björn Töpel <bjorn.topel@intel.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Magnus Karlsson <magnus.karlsson@intel.com> Acked-by: Björn Töpel <bjorn.topel@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Song Liu <songliubraving@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
BPF can adjust gso only for tcp bytestreams. Fail on other gso types.
But only on gso packets. It does not touch this field if !gso_size.
Fixes: b90efd225874 ("bpf: only adjust gso_size on bytestream protocols") Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Yonghong Song <yhs@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Arnd Bergmann [Mon, 4 Mar 2019 20:34:12 +0000 (21:34 +0100)]
bpf: fix sysctl.c warning
When CONFIG_BPF_SYSCALL or CONFIG_SYSCTL is disabled, we get
a warning about an unused function:
kernel/sysctl.c:3331:12: error: 'proc_dointvec_minmax_bpf_stats' defined but not used [-Werror=unused-function]
static int proc_dointvec_minmax_bpf_stats(struct ctl_table *table, int write,
The CONFIG_BPF_SYSCALL check was already handled, but the SYSCTL check
is needed on top.
Fixes: 492ecee892c2 ("bpf: enable program stats") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Christian Brauner <christian@brauner.io> Acked-by: Song Liu <songliubraving@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>