* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Fix missing devices due to PCI bridge test in of_create_pci_dev().
sparc64: Fix disappearing PCI devices on e3500.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
ath9k: Fix IRQ nobody cared issue with ath9k
wireless: zd1211rw: add device ID fix wifi dongle "trust nw-3100"
ath9k: connectivity is lost after Group rekeying is done
has changed the serial core behavior to not to suspend the port if the
device is enabled as a wakeup source. If the AT91 system goes to slow
clock mode, the port should be suspended always and the clocks should be
switched off. The patch attached updates the atmel_serial driver to match
the changes in serial core.
Also, the interrupts are disabled when the clock is disabled. If we
disable the clock with interrupts enabled, an interrupt may get stuck. If
this is the DBGU interrupt, this blocks the OR logic at system controller
and thus all other sysc interrupts.
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Cc: Michael Trimarchi <trimarchimichael@yahoo.it> Cc: Andrew Victor <linux@maxim.org.za> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Current memory cgroup(both in mainline and -mm) doesn't account swap
caches as memory(swap cache support is dropped temporarily now).
So try_to_free_mem_cgroup_pages doesn't reflect the count of pages that
have been moved to swap cache.
But this makes mem_cgroup_shrink_usage fail easily if most of the pages
are anon/shmem, and then shmem_getpage returns -ENOMEM and the process
will be killed.
This patch adds res_counter_check_under_limit to avoid these cases.
BTW, even if swap cache support is enabled again, if a process is moved to
another cgroup, which has been just made, between precharge and
shrink_usage in shmem_getpage, shrink_usage may fail just because there is
no pages to reclaim.
Nick Piggin [Mon, 22 Sep 2008 20:57:50 +0000 (13:57 -0700)]
mm: tiny-shmem fix lock ordering: mmap_sem vs i_mutex
tiny-shmem calls do_truncate in shmem_file_setup. do_truncate takes
i_mutex, and shmem_file_setup is called with mmap_sem held. However
i_mutex nests outside mmap_sem.
Copy the code in shmem.c to avoid this problem.
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Nick Piggin <npiggin@suse.de> Reported-and-tested-by: Ingo Molnar <mingo@elte.hu> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Matt Mackall <mpm@selenic.com> Cc: Hugh Dickins <hugh@veritas.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Kerrisk [Mon, 22 Sep 2008 20:57:49 +0000 (13:57 -0700)]
sys_paccept: disable paccept() until API design is resolved
The reasons for disabling paccept() are as follows:
* The API is more complex than needed. There is AFAICS no demonstrated
use case that the sigset argument of this syscall serves that couldn't
equally be served by the use of pselect/ppoll/epoll_pwait + traditional
accept(). Roland seems to concur with this opinion
(http://thread.gmane.org/gmane.linux.kernel/723953/focus=732255). I
have (more than once) asked Ulrich to explain otherwise
(http://thread.gmane.org/gmane.linux.kernel/723952/focus=731018), but he
does not respond, so one is left to assume that he doesn't know of such
a case.
* The use of a sigset argument is not consistent with other I/O APIs
that can block on a single file descriptor (e.g., read(), recv(),
connect()).
* The behavior of paccept() when interrupted by a signal is IMO strange:
the kernel restarts the system call if SA_RESTART was set for the
handler. I think that it should not do this -- that it should behave
consistently with paccept()/ppoll()/epoll_pwait(), which never restart,
regardless of SA_RESTART. The reasoning here is that the very purpose
of paccept() is to wait for a connection or a signal, and that
restarting in the latter case is probably never useful. (Note: Roland
disagrees on this point, believing that rather paccept() should be
consistent with accept() in its behavior wrt EINTR
(http://thread.gmane.org/gmane.linux.kernel/723953/focus=732255).)
I believe that instead, a simpler API, consistent with Ulrich's other
recent additions, is preferable:
accept4(int fd, struct sockaddr *sa, socklen_t *salen, ind flags);
(This simpler API was originally proposed by Ulrich:
http://thread.gmane.org/gmane.linux.network/92072)
If this simpler API is added, then if we later decide that the sigset
argument really is required, then a suitable bit in 'flags' could be added
to indicate the presence of the sigset argument.
At this point, I am hoping we either will get a counter-argument from
Ulrich about why we really do need paccept()'s sigset argument, or that he
will resubmit the original accept4() patch.
Signed-off-by: Michael Kerrisk <mtk.manpages@gmail.com> Cc: David Miller <davem@davemloft.net> Cc: Davide Libenzi <davidel@xmailserver.org> Cc: Alan Cox <alan@redhat.com> Cc: Ulrich Drepper <drepper@redhat.com> Cc: Jakub Jelinek <jakub@redhat.com> Cc: Roland McGrath <roland@redhat.com> Cc: Oleg Nesterov <oleg@tv-sign.ru> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jonathan Steel [Mon, 22 Sep 2008 20:57:45 +0000 (13:57 -0700)]
kexec: fix segmentation fault in kimage_add_entry
A segmentation fault can occur in kimage_add_entry in kexec.c when loading
a kernel image into memory. The fault occurs because a page is requested
by calling kimage_alloc_page with gfp_mask GFP_KERNEL and the function may
actually return a page with gfp_mask GFP_HIGHUSER. The high mem page is
returned because it was swapped with the kernel page due to the kernel
page being a page that will shortly be copied to.
This patch ensures that kimage_alloc_page returns a page that was created
with the correct gfp flags.
I have verified the change and fixed the whitespace damage of the original
patch. Jonathan did a great job of tracking this down after he hit the
problem. -- Eric
Signed-off-by: Jonathan Steel <jon.steel@esentire.com> Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Acked-by: Simon Horman <horms@verge.net.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Mon, 22 Sep 2008 20:57:44 +0000 (13:57 -0700)]
kernel-doc: allow structs whose members are all private
Struct members may be marked as private by using
/* private: */
before them, as noted in Documentation/kernel-doc-nano-HOWTO.txt
Fix kernel-doc to handle structs whose members are all private;
otherwise invalid XML is generated:
xmlto: input does not validate (status 3)
linux-2.6.27-rc6-git4/Documentation/DocBook/debugobjects.xml:146: element variablelist: validity error : Element variablelist content does not follow the DTD, expecting ((title , titleabbrev?)? , varlistentry+), got ()
Document linux-2.6.27-rc6-git4/Documentation/DocBook/debugobjects.xml does not validate
make[1]: *** [Documentation/DocBook/debugobjects.html] Error 3
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Reported-by: Roland McGrath <roland@redhat.com> Cc: Roland McGrath <roland@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Tue, 16 Sep 2008 10:31:01 +0000 (11:31 +0100)]
[WATCHDOG] wdt285: fix sparse warnings
The wdt285.c watchdog driver is producing a number of
sparse errors due to missing __user attributes to calls
to put_user and copy_to_user, as well as in the prototype
of watchdog_write.
wdt285.c:144:21: warning: incorrect type in argument 1 (different address spaces)
wdt285.c:144:21: expected void [noderef] <asn:1>*to
wdt285.c:144:21: got void *<noident>
wdt285.c:150:9: warning: incorrect type in initializer (different address spaces)
wdt285.c:150:9: expected int const [noderef] <asn:1>*register __p
wdt285.c:150:9: got int *<noident>
wdt285.c:159:9: warning: incorrect type in initializer (different address spaces)
wdt285.c:159:9: expected int const [noderef] <asn:1>*register __p
wdt285.c:159:9: got int *<noident>
wdt285.c:174:9: warning: incorrect type in initializer (different address spaces)
wdt285.c:174:9: expected int const [noderef] <asn:1>*register __p
wdt285.c:174:9: got int *<noident>
wdt285.c:183:12: warning: incorrect type in initializer (incompatible argument 2 (different address spaces))
wdt285.c:183:12: expected int ( *write )( ... )
wdt285.c:183:12: got int ( static [toplevel] *<noident> )( ... )
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
David S. Miller [Mon, 22 Sep 2008 22:42:24 +0000 (15:42 -0700)]
sparc64: Fix missing devices due to PCI bridge test in of_create_pci_dev().
Just like in the arch/sparc64/kernel/of_device.c code fix commit 071d7f4c3b411beae08d27656e958070c43b78b4 ("sparc64: Fix SMP bootup
with CONFIG_STACK_DEBUG or ftrace.") we have to check the OF device
node name for "pci" instead of relying upon the 'device_type' property
being there on all PCI bridges.
Tested by Meelis Roos, and confirmed to make the PCI QFE devices
reappear on the E3500 system.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Tested-by: Steven Noonan <steven@uplinklabs.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
wireless: zd1211rw: add device ID fix wifi dongle "trust nw-3100"
akpm: taken from http://bugzilla.kernel.org/show_bug.cgi?id=11587
I bought the wifi dongle trust nw-3100 wich is in fact a zd1211rw. Its
hardware id was missing in the sources, adding it made it work flawlessly.
Cc: Daniel Drake <dsd@gentoo.org> Cc: Ulrich Kunitz <kune@deine-taler.de> Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: connectivity is lost after Group rekeying is done
Connectivtiy is lost after Group rekeying is done. The keytype
maintained by ath9k is reset when group key is updated. Though
sc_keytype can be reset only for broadcast key the proper fix
would be to use mac80211 provided key type from txinfo during
xmit and get rid of sc_keytype from ath9k ath_softc.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Tested-by: Steven Noonan <steven@uplinklabs.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alan Cox [Mon, 22 Sep 2008 14:58:14 +0000 (15:58 +0100)]
pcmcia: Fix broken abuse of dev->driver_data
PCMCIA abuses dev->private_data in the probe methods. Unfortunately it
continues to abuse it after calling drv->probe() which leads to crashes and
other nasties (such as bogus probes of multifunction devices) giving errors like
pcmcia: registering new device pcmcia0.1
kernel: 0.1: GetNextTuple: No more items
Extract the passed data before calling the driver probe function that way
we don't blow up when the driver reuses dev->private_data as its right.
As its close to the final release just move the hack so it works out,
hopefully someone will be sufficiently embarrassed to produce a nice rework
for 2.6.28.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: jornada720_ts - fix build error ( LONG() usage )
Input: bcm5974 - switch back to normal mode when closing
Atsushi Nemoto [Tue, 5 Aug 2008 14:45:14 +0000 (23:45 +0900)]
[MIPS] vmlinux.lds.S: handle .text.*
The -ffunction-sections puts each text in .text.function_name section.
Without this patch, most functions are placed outside _text..._etext
area and it breaks show_stacktrace(), etc.
Currently simple_tx_hash is hashing inside of udp fragments. As a result
packets are getting getting sent to all queues when they shouldn't be.
This causes a serious performance regression which can be seen by sending
UDP frames larger than mtu on multiqueue devices. This change will make
it so that fragments are hashed only as IP datagrams w/o any protocol
information.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 21 Sep 2008 05:00:40 +0000 (22:00 -0700)]
sparc64: Fix disappearing PCI devices on e3500.
Based upon a bug report by Meelis Roos.
The OF device layer builds properties by matching bus types and
applying 'range' properties as appropriate, up to the root.
The match for "PCI" busses is looking at the 'device_type' property,
and this does work %99 of the time.
But on an E3500 system with a PCI QFE card, the DEC 21153 bridge
sitting above the QFE network interface devices has a 'name' of "pci",
but it completely lacks a 'device_type' property. So we don't match
it as a PCI bus, and subsequently we end up with no resource values at
all for the devices sitting under that DEC bridge.
Signed-off-by: David S. Miller <davem@davemloft.net>
Akinobu Mita [Sat, 13 Sep 2008 10:03:32 +0000 (19:03 +0900)]
mmc_test: initialize mmc_test_lock statically
The mutex mmc_test_lock is initialized at every time mmc_test device
is probed. Probing another mmc_test device may break the mutex, if
the probe function is called while the mutex is locked.
This patch fixes it by statically initializing mmc_test_lock.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
We used to store a binary register snapshot in the "regs" file, so we
set the file size to be the size of this snapshot. This is no longer
valid since we switched to using seq_file.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The debugfs hook atmci_regs_show allocates a temporary buffer for
storing a register snapshot, but it doesn't free it before returning.
Plug this leak.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Andrew Paprocki [Sat, 20 Sep 2008 08:25:19 +0000 (10:25 +0200)]
hwmon: (it87) Fix fan tachometer reading in IT8712F rev 0x7 (I)
The IT8712F v0.9.1 datasheet applies to revisions >= 0x8 (J).
The driver was incorrectly attempting to enable 16-bit fan
readings on rev 0x7 (I) which led to incorrect RPM values.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com> Tested-by: John Gumb <john.gumb@tandberg.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Commit 4611a77 ("[IA64] fix compile failure with non modular builds")
introduced struct fdesc into asm/elf.h, which duplicates KVM's definition.
Remove the latter to avoid the build error.
Signed-off-by: Jes Sorensen <jes@sgi.com> Acked-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Avi Kivity <avi@redhat.com>
* git://oss.sgi.com:8090/xfs/linux-2.6:
[XFS] Don't do I/O beyond eof when unreserving space
[XFS] Fix use-after-free with buffers
[XFS] Prevent lockdep false positives when locking two inodes.
[XFS] Fix barrier status change detection.
[XFS] Prevent direct I/O from mapping extents beyond eof
[XFS] Fix regression introduced by remount fixup
[XFS] Move memory allocations for log tracing out of the critical path
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Fix deadlock on RTNL between bcast join comp and ipoib_stop()
RDMA/nes: Fix client side QP destroy
IB/mlx4: Fix up fast register page list format
mlx4_core: Set RAE and init mtt_sz field in FRMR MPT entries
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: fix deadlock in setting scheduler parameter to zero
sched: fix 2.6.27-rc5 couldn't boot on tulsa machine randomly
Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clockevents: make device shutdown robust
clocksource, acpi_pm.c: fix check for monotonicity
clockevents: remove WARN_ON which was used to gather information
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
Fix compile failure with non modular builds
powerpc: Holly board needs dtbImage target
powerpc: Fix interrupt values for DMA2 in MPC8610 HPCD device tree
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5255/1: Update jornada ssp to remove build errors/warnings
[ARM] omap: back out 'internal_clock' support
[ARM] 5249/1: davinci: remove redundant check in davinci_psc_config()
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Fix SMP bootup with CONFIG_STACK_DEBUG or ftrace.
sparc64: Fix OOPS in psycho_pcierr_intr_other().
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
e100: Use pci_pme_active to clear PME_Status and disable PME#
e1000: prevent corruption of EEPROM/NVM
forcedeth: call restore mac addr in nv_shutdown path
bnx2: Promote vector field in bnx2_irq structure from u16 to unsigned int
sctp: Fix oops when INIT-ACK indicates that peer doesn't support AUTH
sctp: do not enable peer features if we can't do them.
sctp: set the skb->ip_summed correctly when sending over loopback.
udp: Fix rcv socket locking
Manfred Spraul [Wed, 20 Aug 2008 13:39:59 +0000 (15:39 +0200)]
avr32: nmi_enter() without nmi_exit()
While updating the rcu code, I noticed that do_nmi() for AVR32 is odd:
There is an nmi_enter() call without an nmi_exit().
This can't be correct, it breaks rcu (at least the preempt version) and
lockdep.
[haavard.skinnemoen@atmel.com: fixed another case that returned directly] Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
On AVR32, all parameters beyond the 5th are passed on the stack. System
calls don't use the stack -- they borrow a callee-saved register
instead. This means that syscalls that take 6 parameters must be called
through a stub that pushes the last parameter on the stack.
This patch adds a stub for sync_file_range syscall on AVR32
architecture. Tested with uClibc snapshot.
md: Don't wait UNINTERRUPTIBLE for other resync to finish
When two md arrays share some block device (e.g each uses different
partitions on the one device), a resync of one array will wait for
the resync on the other to finish.
This can be a long time and as it currently waits TASK_UNINTERRUPTIBLE,
the softlockup code notices and complains.
So use TASK_INTERRUPTIBLE instead and make sure to flush signals
before calling schedule.
e100: Use pci_pme_active to clear PME_Status and disable PME#
Currently e100 uses pci_enable_wake() to clear pending wake-up events
and disable PME# during intitialization, but that function is not
suitable for this purpose, because it immediately returns error code
if device_may_wakeup() returns false for given device.
Make e100 use pci_pme_active(), which carries out exactly the
required operations, instead.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Christopher Li [Fri, 5 Sep 2008 21:04:05 +0000 (14:04 -0700)]
e1000: prevent corruption of EEPROM/NVM
Andrey reports e1000 corruption, and that a patch in vmware's ESX fixed
it.
The EEPROM corruption is triggered by concurrent access of the EEPROM
read/write. Putting a lock around it solve the problem.
[akpm@linux-foundation.org: use DEFINE_SPINLOCK to avoid confusing lockdep] Signed-off-by: Christopher Li <chrisl@vmware.com> Reported-by: Andrey Borzenkov <arvidjaar@mail.ru> Cc: Zach Amsden <zach@vmware.com> Cc: Pratap Subrahmanyam <pratap@vmware.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: Bruce Allan <bruce.w.allan@intel.com> Cc: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com> Cc: John Ronciak <john.ronciak@intel.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Yinghai Lu [Sat, 13 Sep 2008 20:10:31 +0000 (13:10 -0700)]
forcedeth: call restore mac addr in nv_shutdown path
after
| commit f735a2a1a4f2a0f5cd823ce323e82675990469e2
| Author: Tobias Diedrich <ranma+kernel@tdiedrich.de>
| Date: Sun May 18 15:02:37 2008 +0200
|
| [netdrvr] forcedeth: setup wake-on-lan before shutting down
|
| When hibernating in 'shutdown' mode, after saving the image the suspend hook
| is not called again.
| However, if the device is in promiscous mode, wake-on-lan will not work.
| This adds a shutdown hook to setup wake-on-lan before the final shutdown.
|
| Signed-off-by: Tobias Diedrich <ranma+kernel@tdiedrich.de>
| Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
my servers with nvidia ck804 and mcp55 will reverse mac address with kexec.
it turns out that we need to restore the mac addr in nv_shutdown().
[akpm@linux-foundation.org: fix typo in printk] Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com> Cc: Tobias Diedrich <ranma+kernel@tdiedrich.de> Cc: Ayaz Abdulla <aabdulla@nvidia.com> Cc: Jeff Garzik <jeff@garzik.org> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Benjamin Li [Thu, 18 Sep 2008 23:46:11 +0000 (16:46 -0700)]
bnx2: Promote vector field in bnx2_irq structure from u16 to unsigned int
The bnx2 driver stores/uses the irq value from the pci_dev internally.
But when it stores the irq value, it has been performing an
integer demotion. Because of the recent changes made to
arch/x86/kernel/io_apic.c, the new method in creating the irq value
(using build_irq_for_pci_dev()) has exposed this bug on x86 systems.
Because of this demotion when calling request_irq() from
bnx2_request_irq(), the driver would get a return code of -EINVAL.
This is because the kernel could not find the requested irq descriptor.
By storing the irq value properly, the kernel can find the correct
irq descriptor and the bnx2 driver can operate normally.
Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sctp: Fix oops when INIT-ACK indicates that peer doesn't support AUTH
If INIT-ACK is received with SupportedExtensions parameter which
indicates that the peer does not support AUTH, the packet will be
silently ignore, and sctp_process_init() do cleanup all of the
transports in the association.
When T1-Init timer is expires, OOPS happen while we try to choose
a different init transport.
The solution is to only clean up the non-active transports, i.e
the ones that the peer added. However, that introduces a problem
with sctp_connectx(), because we don't mark the proper state for
the transports provided by the user. So, we'll simply mark
user-provided transports as ACTIVE. That will allow INIT
retransmissions to work properly in the sctp_connectx() context
and prevent the crash.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sctp: do not enable peer features if we can't do them.
Do not enable peer features like addip and auth, if they
are administratively disabled localy. If the peer resports
that he supports something that we don't, neither end can
use it so enabling it is pointless. This solves a problem
when talking to a peer that has auth and addip enabled while
we do not. Found by Andrei Pelinescu-Onciul <andrei@iptel.org>.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[ARM] 5255/1: Update jornada ssp to remove build errors/warnings
* Adds ssp functions into header so we don't get
"implicit declaration" error at builtime.
* Converts jornada_ssp_start/end functions into voids with
proper declarations (to avoid "prototype..." warning).
* Sorts include files in alphabetical order
* Minor comment changes
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
sctp: set the skb->ip_summed correctly when sending over loopback.
Loopback used to clobber the ip_summed filed which sctp then used
to figure out if it needed to do checksumming or not. Now that
loopback doesn't do that any more, sctp needs to set the ip_summed
field correctly.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 17 Sep 2008 19:58:11 +0000 (20:58 +0100)]
[ARM] omap: back out 'internal_clock' support
The structures weren't ready for this change:
arch/arm/plat-omap/devices.c:320: error: 'struct omap_mmc_conf' has no member named 'internal_clock'
arch/arm/plat-omap/devices.c:326: error: implicit declaration of function 'omap_ctrl_readl'
arch/arm/plat-omap/devices.c:326: error: 'OMAP2_CONTROL_DEVCONF0' undeclared (first use in this function)
arch/arm/plat-omap/devices.c:328: error: implicit declaration of function 'omap_ctrl_writel'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
James Bottomley [Tue, 9 Sep 2008 14:04:18 +0000 (14:04 +0000)]
Fix compile failure with non modular builds
Commit deac93df26b20cf8438339b5935b5f5643bc30c9 ("lib: Correct printk
%pF to work on all architectures") broke the non modular builds by
moving an essential function into modules.c. Fix this by moving it
out again and into asm/sections.h as an inline. To do this, the
definition of struct ppc64_opd_entry has been lifted out of modules.c
and put in asm/elf.h where it belongs.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
One of the changes in the bootwrapper makefile introduced the dtbImage
targets for boards that need a simple zImage with a DTB embedded in
them (595be948cce574ff2d5dde5d0426a636a4363c70, "[POWERPC]
bootwrapper: Build multiple cuImages"). When this was done, it broke
booting on the Holly board as the zImage.holly wrapper did not get the
DTB embedded properly.
This changes the target for the Holly board to a dtbImage so that the
wrapper includes the vmlinux, wrapper bits, and DTB.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
[XFS] Don't do I/O beyond eof when unreserving space
When unreserving space with boundaries that are not block aligned we round
up the start and round down the end boundaries and then use this function,
xfs_zero_remaining_bytes(), to zero the parts of the blocks that got
dropped during the rounding. The problem is we don't consider if these
blocks are beyond eof. Worse still is if we encounter delayed allocations
beyond eof we will try to use the magic delayed allocation block number as
a real block number. If the file size is ever extended to expose these
blocks then we'll go through xfs_zero_eof() to zero them anyway.
SGI-PV: 983683
SGI-Modid: xfs-linux-melb:xfs-kern:32055a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com> Signed-off-by: Christoph Hellwig <hch@infradead.org>
We have a use-after-free issue where log completions access buffers via
the buffer log item and the buffer has already been freed. Fix this by
taking a reference on the buffer when attaching the buffer log item and
release the hold when the buffer log item is detached and we no longer
need the buffer. Also create a new function xfs_buf_item_free() to combine
some common code.
SGI-PV: 985757
SGI-Modid: xfs-linux-melb:xfs-kern:32025a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com> Signed-off-by: Christoph Hellwig <hch@infradead.org>
David Chinner [Wed, 17 Sep 2008 06:51:21 +0000 (16:51 +1000)]
[XFS] Prevent lockdep false positives when locking two inodes.
If we call xfs_lock_two_inodes() to grab both the iolock and the ilock,
then drop the ilocks on both inodes, then grab them again (as
xfs_swap_extents() does) then lockdep will report a locking order problem.
This is a false positive.
To avoid this, disallow xfs_lock_two_inodes() fom locking both inode locks
at once - force calers to make two separate calls. This means that nested
dropping and regaining of the ilocks will retain the same lockdep subclass
and so lockdep will not see anything wrong with this code.
SGI-PV: 986238
SGI-Modid: xfs-linux-melb:xfs-kern:31999a
Signed-off-by: David Chinner <david@fromorbit.com> Signed-off-by: Christoph Hellwig <hch@infradead.org> Signed-off-by: Peter Leckie <pleckie@sgi.com> Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
[XFS] Prevent direct I/O from mapping extents beyond eof
With the help from some tracing I found that we try to map extents beyond
eof when doing a direct I/O read. It appears that the way to inform the
generic direct I/O path (ie do_direct_IO()) that we have breached eof is
to return an unmapped buffer from xfs_get_blocks_direct(). This will cause
do_direct_IO() to jump to the hole handling code where is will check for
eof and then abort.
This problem was found because a direct I/O read was trying to map beyond
eof and was encountering delayed allocations. The delayed allocations
beyond eof are speculative allocations and they didn't get converted when
the direct I/O flushed the file because there was only enough space in the
current AG to convert and write out the dirty pages within eof. Note that
xfs_iomap_write_allocate() wont necessarily convert all the delayed
allocation passed to it - it will return after allocating the first extent
- so if the delayed allocation extends beyond eof then it will stay that
way.
SGI-PV: 983683
SGI-Modid: xfs-linux-melb:xfs-kern:31929a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com> Signed-off-by: Christoph Hellwig <hch@infradead.org>
Logically we would return an error in xfs_fs_remount code to prevent users
from believing they might have changed mount options using remount which
can't be changed.
But unfortunately mount(8) adds all options from mtab and fstab to the
mount arguments in some cases so we can't blindly reject options, but have
to check for each specified option if it actually differs from the
currently set option and only reject it if that's the case.
Until that is implemented we return success for every remount request, and
silently ignore all options that we can't actually change.
SGI-PV: 985710
SGI-Modid: xfs-linux-melb:xfs-kern:31908a
Signed-off-by: Christoph Hellwig <hch@infradead.org> Signed-off-by: Tim Shimmin <tes@sgi.com> Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
[XFS] Move memory allocations for log tracing out of the critical path
Memory allocations for log->l_grant_trace and iclog->ic_trace are done on
demand when the first event is logged. In xlog_state_get_iclog_space() we
call xlog_trace_iclog() under a spinlock and allocating memory here can
cause us to sleep with a spinlock held and deadlock the system.
For the log grant tracing we use KM_NOSLEEP but that means we can lose
trace entries. Since there is no locking to serialize the log grant
tracing we could race and have multiple allocations and leak memory.
So move the allocations to where we initialize the log/iclog structures.
Use KM_NOFS to avoid recursing into the filesystem and drop log->l_trace
since it's not even used.
SGI-PV: 983738
SGI-Modid: xfs-linux-melb:xfs-kern:31896a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com> Signed-off-by: Christoph Hellwig <hch@infradead.org>
Arjan van de Ven [Mon, 15 Sep 2008 23:43:18 +0000 (16:43 -0700)]
warn: Turn the netdev timeout WARN_ON() into a WARN()
this patch turns the netdev timeout WARN_ON_ONCE() into a WARN_ONCE(),
so that the device and driver names are inside the warning message.
This helps automated tools like kerneloops.org to collect the data
and do statistics, as well as making it more likely that humans
cut-n-paste the important message as part of a bugreport.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Miller [Tue, 16 Sep 2008 22:00:11 +0000 (15:00 -0700)]
Fix PNP build failure, bugzilla #11276
This fill fix the following regression list entry:
Bug-Entry : http://bugzilla.kernel.org/show_bug.cgi?id=11276
Subject : build error: CONFIG_OPTIMIZE_INLINING=y causes gcc 4.2 to do stupid things
Submitter : Randy Dunlap <randy.dunlap@oracle.com>
Date : 2008-08-06 17:18 (38 days old)
References : http://marc.info/?l=linux-kernel&m=121804329014332&w=4
http://lkml.org/lkml/2008/7/22/353
Handled-By : Bjorn Helgaas <bjorn.helgaas@hp.com>
Patch : http://lkml.org/lkml/2008/7/22/364
with what I believe is a better fix than the one referenced
in the regression entry above.
These PNP header interfaces try to work in such a way that
you can reference some of them even if PNP is not enabled,
and the compiler was expected to optimize everything away.
Which is mostly fine, except that there was one interface
for which there was not provided an inline "NOP" implementation.
Once we add that, all of these compile failures cannot handle
any more.
pnp: Provide NOP inline implementation of pnp_get_resource() when !PNP
Fixes kernel bugzilla #11276.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes kernel regression for 2.6.27-rc in
http://bugzilla.kernel.org/show_bug.cgi?id=11547
The change to split 8390 into old isa and non-isa versions
overlooked this driver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit bc19d6e0b74ef03a3baf035412c95192b54dfc6f, which as
Larry Finger reports causes the radio LED on his system to no longer
respond to rfkill switch events.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net> Requested-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Timur Tabi [Tue, 9 Sep 2008 19:43:39 +0000 (14:43 -0500)]
powerpc: Fix interrupt values for DMA2 in MPC8610 HPCD device tree
For Freescale 8xxx devices that use an MPIC, the interrupt numbers in
the device tree must be 16 greater than the values documented in the
reference manual. In these chips, the MPIC is wired to use the first
16 numbers for external interrupts, but the documentation numbers
internal interrupts from 0.
In the MPC8610 HPCD device tree, the interrupt properties for the DMA
channels for DMA2 were not the adjusted values. This fixes that.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Thomas Gleixner [Tue, 16 Sep 2008 18:32:50 +0000 (11:32 -0700)]
clockevents: make device shutdown robust
The device shut down does not cleanup the next_event variable of the
clock event device. So when the device is reactivated the possible
stale next_event value can prevent the device to be reprogrammed as it
claims to wait on a event already.
This is the root cause of the resurfacing suspend/resume problem,
where systems need key press to come back to life.
Fix this by setting next_event to KTIME_MAX when the device is shut
down. Use a separate function for shutdown which takes care of that
and only keep the direct set mode call in the broadcast code, where we
can not touch the next_event value.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
IPoIB: Fix deadlock on RTNL between bcast join comp and ipoib_stop()
Taking rtnl_lock in ipoib_mcast_join_complete() causes a deadlock with
ipoib_stop(). We avoid it by scheduling the piece of code that takes
the lock on ipoib_workqueue instead of executing it directly. This
works because we only flush the ipoib_workqueue with the RTNL not held.
The deadlock happens because ipoib_stop() calls ipoib_ib_dev_down()
which calls ipoib_mcast_dev_flush(), which calls ipoib_mcast_free(),
which calls ipoib_mcast_leave(). The latter calls
ib_sa_free_multicast(), and this waits until the multicast completion
handler finishes. This handler is ipoib_mcast_join_complete(), which
waits for the rtnl_lock(), which was already taken by ipoib_stop().
This bug was introduced in commit a77a57a1 ("IPoIB: Fix deadlock on
RTNL in ipoib_stop()").
Signed-off-by: Yossi Etigin <yosefe@voltaire.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix QP not being destroyed properly on the client, which leads to
userspace programs hanging on exit. This is a missing chunk from the
connection management rewrite in commit 6492cdf3 ("RDMA/nes: CM
connection setup/teardown rework").
Signed-off-by: Faisal Latif <flatif@neteffect.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
projects / mirror_ubuntu-disco-kernel.git / log