DIV_ROUND_UP_ULL adds the two arguments and then invokes
DIV_ROUND_DOWN_ULL. But on a 32bit system the addition of two 32 bit
values can overflow. DIV_ROUND_DOWN_ULL does it correctly and stashes
the addition into a unsigned long long so cast the result to unsigned
long long here to avoid the overflow condition.
[akpm@linux-foundation.org: DIV_ROUND_UP_ULL must be an rval] Link: http://lkml.kernel.org/r/20190625100518.30753-1-vkoul@kernel.org Signed-off-by: Vinod Koul <vkoul@kernel.org> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Setting invalid value to /sys/devices/system/cpu/cpuX/hotplug/fail
can control `struct cpuhp_step *sp` address, results in the following
global-out-of-bounds read.
The buggy address belongs to the variable:
cpu_hotplug_lock+0x98/0xa0
Memory state around the buggy address: ffffffff89734300: fa fa fa fa 00 00 00 00 00 00 00 00 00 00 00 00 ffffffff89734380: fa fa fa fa 00 00 00 00 00 00 00 00 00 00 00 00
>ffffffff89734400: 00 00 00 00 fa fa fa fa 00 00 00 00 fa fa fa fa
^ ffffffff89734480: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffffffff89734500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Add a sanity check for the value written from user space.
A kernel which boots in 5-level paging mode crashes in a small percentage
of cases if KASLR is enabled.
This issue was tracked down to the case when the kernel image unpacks in a
way that it crosses an 1G boundary. The crash is caused by an overrun of
the PMD page table in __startup_64() and corruption of P4D page table
allocated next to it. This particular issue is not visible with 4-level
paging as P4D page tables are not used.
But the P4D and the PUD calculation have similar problems.
The PMD index calculation is wrong due to operator precedence, which fails
to confine the PMDs in the PMD array on wrap around.
The P4D calculation for 5-level paging and the PUD calculation calculate
the first index correctly, but then blindly increment it which causes the
same issue when a kernel image is located across a 512G and for 5-level
paging across a 46T boundary.
This wrap around mishandling was introduced when these parts moved from
assembly to C.
Restore it to the correct behaviour.
Fixes: c88d71508e36 ("x86/boot/64: Rewrite startup_64() in C") Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lkml.kernel.org/r/20190620112345.28833-1-kirill.shutemov@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since commit 605ad7f184b60cfaacbc038aa6c55ee68dee3c89 "tcp: refine TSO autosizing",
outbound throughput is dramatically reduced for some connections, as sis900
is doing TX completion within idle states only.
Make TX completion happen after every transmitted packet.
Test:
netperf
before patch:
> netperf -H remote -l -2000000 -- -s 1000000
MIGRATED TCP STREAM TEST from 0.0.0.0 () port 0 AF_INET to 95.223.112.76 () port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 327680 327680 253.44 0.06
after patch:
> netperf -H remote -l -10000000 -- -s 1000000
MIGRATED TCP STREAM TEST from 0.0.0.0 () port 0 AF_INET to 95.223.112.76 () port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 327680 327680 5.38 14.89
Thx to Dave Miller and Eric Dumazet for helpful hints
Signed-off-by: Sergej Benilov <sergej.benilov@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The arc4 crypto is mandatory at ppp_mppe probe time, so let's put a
softdep line, so that the corresponding module gets prepared
gracefully. Without this, a simple inclusion to initrd via dracut
failed due to the missing dependency, for example.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Certain cards in conjunction with certain switches need a little more
time for link setup that results in ethtool link test failure after
offline test. Patch adds a loop that waits for a link setup finish.
Changes in v2:
- added fixes header
Fixes: 4276e47e2d1c ("be2net: Add link test to list of ethtool self tests.") Signed-off-by: Petr Oros <poros@redhat.com> Reviewed-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
omap3xxx_prm_enable_io_wakeup() is marked __init, but its caller is not, so
we get a warning with clang-8:
WARNING: vmlinux.o(.text+0x343c8): Section mismatch in reference from the function omap3xxx_prm_late_init() to the function .init.text:omap3xxx_prm_enable_io_wakeup()
The function omap3xxx_prm_late_init() references
the function __init omap3xxx_prm_enable_io_wakeup().
This is often because omap3xxx_prm_late_init lacks a __init
annotation or the annotation of omap3xxx_prm_enable_io_wakeup is wrong.
When building with gcc, omap3xxx_prm_enable_io_wakeup() is always
inlined, so we never noticed in the past.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Andrew Murray <andrew.murray@arm.com> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
perf_sample_regs_user() uses 'current->mm' to test for the presence of
userspace, but this is insufficient, consider use_mm().
A better test is: '!(current->flags & PF_KTHREAD)', exec() clears
PF_KTHREAD after it sets the new ->mm but before it drops to userspace
for the first time.
Possibly obsoletes: bf05fc25f268 ("powerpc/perf: Fix oops when kthread execs user process")
Reported-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com> Reported-by: Young Xiao <92siuyang@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Will Deacon <will.deacon@arm.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 4018994f3d87 ("perf: Add ability to attach user level registers dump to sample") Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Starting with ACPI 6.2 bits 1 and 2 of the BGRT status field are no longer
reserved. These bits are now used to indicate if the image needs to be
rotated before being displayed.
The first device using these bits has now shown up (the GPD MicroPC) and
the reserved bits check causes us to reject the valid BGRT table on this
device.
Rather then changing the reserved bits check, allowing only the 2 new bits,
instead just completely remove it so that we do not end up with a similar
problem when more bits are added in the future.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If we do a clk_get() for a clock that does not exists, we have
_ti_omap4_clkctrl_xlate() return uninitialized data if no match
is found. This can be seen in some cases with SLAB_DEBUG enabled:
Unable to handle kernel paging request at virtual address 5a5a5a5a
...
clk_hw_create_clk.part.33
sysc_notifier_call
notifier_call_chain
blocking_notifier_call_chain
device_add
Let's fix this by setting a found flag only when we find a match.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Fixes: 88a172526c32 ("clk: ti: add support for clkctrl clocks") Signed-off-by: Tony Lindgren <tony@atomide.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This check might otherwise be useful to stop users from using a non-linux
compiler, but if you're doing that you are going to have a lot more
trouble anyway.
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21149/ Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Cc: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The VMCI handle array has an integer overflow in
vmci_handle_arr_append_entry when it tries to expand the array. This can be
triggered from a guest, since the doorbell link hypercall doesn't impose a
limit on the number of doorbell handles that a VM can create in the
hypervisor, and these handles are stored in a handle array.
In this change, we introduce a mandatory max capacity for handle
arrays/lists to avoid excessive memory usage.
This patch follows Alan Stern's recent patch:
"p54: Fix race between disconnect and firmware loading"
that overhauled carl9170 buggy firmware loading and driver
unbinding procedures.
Since the carl9170 code was adapted from p54 it uses the
same functions and is likely to have the same problem, but
it's just that the syzbot hasn't reproduce them (yet).
a summary from the changes (copied from the p54 patch):
* Call usb_driver_release_interface() rather than
device_release_driver().
* Lock udev (the interface's parent) before unbinding the
driver instead of locking udev->parent.
* During the firmware loading process, take a reference
to the USB interface instead of the USB device.
* Don't take an unnecessary reference to the device during
probe (and then don't drop it during disconnect).
and
* Make sure to prevent use-after-free bugs by explicitly
setting the driver context to NULL after signaling the
completion.
Cc: <stable@vger.kernel.org> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
syzkallar found a 32-byte memory leak in a rarely executed error
case. The transaction complete work item was not freed if put_user()
failed when writing the BR_TRANSACTION_COMPLETE to the user command
buffer. Fixed by freeing it before put_user() is called.
The interrupt handler `pci230_interrupt()` causes a null pointer
dereference for a PCI260 card. There is no analog output subdevice for
a PCI260. The `dev->write_subdev` subdevice pointer and therefore the
`s_ao` subdevice pointer variable will be `NULL` for a PCI260. The
following call near the end of the interrupt handler results in the null
pointer dereference for a PCI260:
comedi_handle_events(dev, s_ao);
Fix it by only calling the above function if `s_ao` is valid.
Note that the other uses of `s_ao` in the calls
`pci230_handle_ao_nofifo(dev, s_ao);` and `pci230_handle_ao_fifo(dev,
s_ao);` will never be reached for a PCI260, so they are safe.
Fixes: 39064f23284c ("staging: comedi: amplc_pci230: use comedi_handle_events()") Cc: <stable@vger.kernel.org> # v3.19+ Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The interrupt handler `dt282x_interrupt()` causes a null pointer
dereference for those supported boards that have no analog output
support. For these boards, `dev->write_subdev` will be `NULL` and
therefore the `s_ao` subdevice pointer variable will be `NULL`. In that
case, the following call near the end of the interrupt handler results
in a null pointer dereference:
comedi_handle_events(dev, s_ao);
Fix it by only calling the above function if `s_ao` is valid.
(There are other uses of `s_ao` by the interrupt handler that may or may
not be reached depending on values of hardware registers. Trust that
they are reliable for now.)
Note:
commit 4f6f009b204f ("staging: comedi: dt282x: use comedi_handle_events()")
propagates an earlier error from
commit f21c74fa4cfe ("staging: comedi: dt282x: use cfc_handle_events()").
Fixes: 4f6f009b204f ("staging: comedi: dt282x: use comedi_handle_events()") Cc: <stable@vger.kernel.org> # v3.19+ Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The old commit 6e4b74e4690d ("usb: renesas: fix scheduling in atomic
context bug") fixed an atomic issue by using workqueue for the shdmac
dmaengine driver. However, this has a potential race condition issue
between the work pending and usbhsg_ep_free_request() in gadget mode.
When usbhsg_ep_free_request() is called while pending the queue,
since the work_struct will be freed and then the work handler is
called, kernel panic happens on process_one_work().
To fix the issue, if we could call cancel_work_sync() at somewhere
before the free request, it could be easy. However,
the usbhsg_ep_free_request() is called on atomic (e.g. f_ncm driver
calls free request via gether_disconnect()).
For now, almost all users are having "USB-DMAC" and the DMAengine
driver can be used on atomic. So, this patch adds a workaround for
a race condition to call the DMAengine APIs without the workqueue.
This means we still have TODO on shdmac environment (SH7724), but
since it doesn't have SMP, the race condition might not happen.
Fixes: ab330cf3888d ("usb: renesas_usbhs: add support for USB-DMAC") Cc: <stable@vger.kernel.org> # v4.1+ Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On spin lock release in rx_submit, gether_disconnect get a chance to
run, it makes port_usb NULL, rx_submit access NULL port USB, hence null
pointer crash.
Fixed by releasing the lock in rx_submit after port_usb is used.
The syzbot fuzzer found a bug in the p54 USB wireless driver. The
issue involves a race between disconnect and the firmware-loader
callback routine, and it has several aspects.
One big problem is that when the firmware can't be loaded, the
callback routine tries to unbind the driver from the USB _device_ (by
calling device_release_driver) instead of from the USB _interface_ to
which it is actually bound (by calling usb_driver_release_interface).
The race involves access to the private data structure. The driver's
disconnect handler waits for a completion that is signalled by the
firmware-loader callback routine. As soon as the completion is
signalled, you have to assume that the private data structure may have
been deallocated by the disconnect handler -- even if the firmware was
loaded without errors. However, the callback routine does access the
private data several times after that point.
Another problem is that, in order to ensure that the USB device
structure hasn't been freed when the callback routine runs, the driver
takes a reference to it. This isn't good enough any more, because now
that the callback routine calls usb_driver_release_interface, it has
to ensure that the interface structure hasn't been freed.
Finally, the driver takes an unnecessary reference to the USB device
structure in the probe function and drops the reference in the
disconnect handler. This extra reference doesn't accomplish anything,
because the USB core already guarantees that a device structure won't
be deallocated while a driver is still bound to any of its interfaces.
To fix these problems, this patch makes the following changes:
Call usb_driver_release_interface() rather than
device_release_driver().
Don't signal the completion until after the important
information has been copied out of the private data structure,
and don't refer to the private data at all thereafter.
Lock udev (the interface's parent) before unbinding the driver
instead of locking udev->parent.
During the firmware loading process, take a reference to the
USB interface instead of the USB device.
Don't take an unnecessary reference to the device during probe
(and then don't drop it during disconnect).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: syzbot+200d4bb11b23d929335f@syzkaller.appspotmail.com CC: <stable@vger.kernel.org> Acked-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Reading LSR unconditionally but processing the error flags only if
UART_IIR_RDI bit was set before in IIR may lead to a loss of transmission
error information on UARTs where the transmission error flags are cleared
by a read of LSR. Information are lost in case an error is detected right
before the read of LSR while processing e.g. an UART_IIR_THRI interrupt.
Signed-off-by: Oliver Barta <o.barta89@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Fixes: 2e9fe5391083 ("serial: 8250: Don't service RX FIFO if interrupts are disabled") Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Per the 802.11 specification, vendor IEs are (at minimum) only required
to contain an OUI. A type field is also included in ieee80211.h (struct
ieee80211_vendor_ie) but doesn't appear in the specification. The
remaining fields (subtype, version) are a convention used in WMM
headers.
Thus, we should not reject vendor-specific IEs that have only the
minimum length (3 bytes) -- we should skip over them (since we only want
to match longer IEs, that match either WMM or WPA formats). We can
reject elements that don't have the minimum-required 3 byte OUI.
While we're at it, move the non-standard subtype and version fields into
the WMM structs, to avoid this confusion in the future about generic
"vendor header" attributes.
Fixes: 685c9b7750bf ("mwifiex: Abort at too short BSS descriptor element") Cc: Takashi Iwai <tiwai@suse.de> Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently mwifiex_update_bss_desc_with_ie() implicitly assumes that
the source descriptor entries contain the enough size for each type
and performs copying without checking the source size. This may lead
to read over boundary.
Fix this by putting the source size check in appropriate places.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The index to access the threads tls array is controlled by userspace
via syscall: sys_ptrace(), hence leading to a potential exploitation
of the Spectre variant 1 vulnerability.
The index can be controlled from:
ptrace -> arch_ptrace -> do_get_thread_area.
Fix this by sanitizing the user supplied index before using it to access
the p->thread.tls_array.
The index to access the threads ptrace_bps is controlled by userspace via
syscall: sys_ptrace(), hence leading to a potential exploitation of the
Spectre variant 1 vulnerability.
The index can be controlled from:
ptrace -> arch_ptrace -> ptrace_get_debugreg.
Fix this by sanitizing the user supplied index before using it access
thread->ptrace_bps.
In reboot tests on several devices we were seeing a "use after free"
when slub_debug or KASAN was enabled. The kernel complained about:
Unable to handle kernel paging request at virtual address 6b6b6c2b
...which is a classic sign of use after free under slub_debug. The
stack crawl in kgdb looked like:
0 test_bit (addr=<optimized out>, nr=<optimized out>)
1 bfq_bfqq_busy (bfqq=<optimized out>)
2 bfq_select_queue (bfqd=<optimized out>)
3 __bfq_dispatch_request (hctx=<optimized out>)
4 bfq_dispatch_request (hctx=<optimized out>)
5 0xc056ef00 in blk_mq_do_dispatch_sched (hctx=0xed249440)
6 0xc056f728 in blk_mq_sched_dispatch_requests (hctx=0xed249440)
7 0xc0568d24 in __blk_mq_run_hw_queue (hctx=0xed249440)
8 0xc0568d94 in blk_mq_run_work_fn (work=<optimized out>)
9 0xc024c5c4 in process_one_work (worker=0xec6d4640, work=0xed249480)
10 0xc024cff4 in worker_thread (__worker=0xec6d4640)
Digging in kgdb, it could be found that, though bfqq looked fine,
bfqq->bic had been freed.
Through further digging, I postulated that perhaps it is illegal to
access a "bic" (AKA an "icq") after bfq_exit_icq() had been called
because the "bic" can be freed at some point in time after this call
is made. I confirmed that there certainly were cases where the exact
crashing code path would access the "bic" after bfq_exit_icq() had
been called. Sspecifically I set the "bfqq->bic" to (void *)0x7 and
saw that the bic was 0x7 at the time of the crash.
To understand a bit more about why this crash was fairly uncommon (I
saw it only once in a few hundred reboots), you can see that much of
the time bfq_exit_icq_fbqq() fully frees the bfqq and thus it can't
access the ->bic anymore. The only case it doesn't is if
bfq_put_queue() sees a reference still held.
However, even in the case when bfqq isn't freed, the crash is still
rare. Why? I tracked what happened to the "bic" after the exit
routine. It doesn't get freed right away. Rather,
put_io_context_active() eventually called put_io_context() which
queued up freeing on a workqueue. The freeing then actually happened
later than that through call_rcu(). Despite all these delays, some
extra debugging showed that all the hoops could be jumped through in
time and the memory could be freed causing the original crash. Phew!
To make a long story short, assuming it truly is illegal to access an
icq after the "exit_icq" callback is finished, this patch is needed.
Cc: stable@vger.kernel.org Reviewed-by: Paolo Valente <paolo.valente@unimore.it> Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Dell headset mode platform with ALC236.
It doesn't recording after system resume from S3.
S3 mode was deep. s2idle was not has this issue.
S3 deep will cut of codec power. So, the register will back to default
after resume back.
This patch will solve this issue.
In some cases, using the 'truncate' command to extend a UDF file results
in a mismatch between the length of the file's extents (specifically, due
to incorrect length of the final NOT_ALLOCATED extent) and the information
(file) length. The discrepancy can prevent other operating systems
(i.e., Windows 10) from opening the file.
Two particular errors have been observed when extending a file:
1. The final extent is larger than it should be, having been rounded up
to a multiple of the block size.
B. The final extent is not shorter than it should be, due to not having
been updated when the file's information length was increased.
[JK: simplified udf_do_extend_final_block(), fixed up some types]
Fixes: 2c948b3f86e5 ("udf: Avoid IO in udf_clear_inode") CC: stable@vger.kernel.org Signed-off-by: Steven J. Magnani <steve@digidescorp.com> Link: https://lore.kernel.org/r/1561948775-5878-1-git-send-email-steve@digidescorp.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The directory may have been removed when entering
fscrypt_ioctl_set_policy(). If so, the empty_dir() check will return
error for ext4 file system.
ext4_rmdir() sets i_size = 0, then ext4_empty_dir() reports an error
because 'inode->i_size < EXT4_DIR_REC_LEN(1) + EXT4_DIR_REC_LEN(2)'. If
the fs is mounted with errors=panic, it will trigger a panic issue.
Add the check IS_DEADDIR() to fix this problem.
Fixes: 9bd8212f981e ("ext4 crypto: add encryption policy and password salt support") Cc: <stable@vger.kernel.org> # v4.1+ Signed-off-by: Hongjie Fang <hongjiefang@asrmicro.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
rpc_clnt_add_xprt take a reference to struct rpc_xprt_switch, but forget
to release it before return, may lead to a memory leak.
Signed-off-by: Lin Yi <teroincn@163.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Run below script as root, dquot_add_space will return -EDQUOT since
__dquot_transfer call dquot_add_space with flags=0, and dquot_add_space
think it's a preallocation. Fix it by set flags as DQUOT_SPACE_WARN.
Left shifting the signed int value 1 by 31 bits has undefined behaviour
and the shift amount oq_no can be as much as 63. Fix this by using
BIT_ULL(oq_no) instead.
Addresses-Coverity: ("Bad shift operation") Fixes: f21fb3ed364b ("Add support of Cavium Liquidio ethernet adapters") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A similar fix to Patch "ip_tunnel: allow not to count pkts on tstats by
setting skb's dev to NULL" is also needed by ip6_tunnel.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The copy_from_user() function returns the number of bytes remaining
to be copied but we want to return a negative error code. Otherwise
the callers treat it as a successful copy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190618131843.GA29463@mwanda Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Some transceivers may comply with SFF-8472 even though they do not
implement the Digital Diagnostic Monitoring (DDM) interface described in
the spec. The existence of such area is specified by the 6th bit of byte
92, set to 1 if implemented.
Currently, without checking this bit, bnx2x fails trying to read sfp
module's EEPROM with the follow message:
ethtool -m enP5p1s0f1
Cannot get Module EEPROM data: Input/output error
Because it fails to read the additional 256 bytes in which it is assumed
to exist the DDM data.
This issue was noticed using a Mellanox Passive DAC PN 01FT738. The EEPROM
data was confirmed by Mellanox as correct and similar to other Passive
DACs from other manufacturers.
Signed-off-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com> Acked-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Stopping external metadata arrays during resync/recovery causes
retries, loop of interrupting and starting reconstruction, until it
hit at good moment to stop completely. While these retries
curr_mark_cnt can be small- especially on HDD drives, so subtraction
result can be smaller than 0. However it is casted to uint without
checking. As a result of it the status bar in /proc/mdstat while stopping
is strange (it jumps between 0% and 99%).
The real problem occurs here after commit 72deb455b5ec ("block: remove
CONFIG_LBDAF"). Sector_div() macro has been changed, now the
divisor is casted to uint32. For db = -8 the divisior(db/32-1) becomes 0.
Check if db value can be really counted and replace these macro by
div64_u64() inline.
Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@intel.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Switch qmimux_unregister_device() and qmi_wwan_disconnect() to
use unregister_netdevice_queue() and unregister_netdevice_many()
instead of unregister_netdevice(). This avoids RCU stalls which
have been observed on device disconnect in certain setups otherwise.
Fixes: c6adf77953bc ("net: usb: qmi_wwan: add qmap mux protocol support") Cc: Daniele Palmas <dnlplm@gmail.com> Signed-off-by: Reinhard Speyerer <rspmn@arcor.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The QMAP code in the qmi_wwan driver is based on the CodeAurora GobiNet
driver which does not process QMAP padding in the RX path correctly.
Add support for QMAP padding to qmimux_rx_fixup() according to the
description of the rmnet driver.
Fixes: c6adf77953bc ("net: usb: qmi_wwan: add qmap mux protocol support") Cc: Daniele Palmas <dnlplm@gmail.com> Signed-off-by: Reinhard Speyerer <rspmn@arcor.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In multiple SSID cases, it takes time to prepare every AP interface
to be ready in initializing phase. If a sta already knows everything it
needs to join one of the APs and sends authentication to the AP which
is not fully prepared at this point of time, AP's channel context
could be NULL. As a result, warning message occurs.
Even worse, if the AP is under attack via tools such as MDK3 and massive
authentication requests are received in a very short time, console will
be hung due to kernel warning messages.
WARN_ON_ONCE() could be a better way for indicating warning messages
without duplicate messages to flood the console.
Johannes: We still need to address the underlying problem, but we
don't really have a good handle on it yet. Suppress the
worst side-effects for now.
kvm_device->destroy() seems to be supposed to free its kvm_device
struct, but vgic_its_destroy() is not currently doing this,
resulting in a memory leak, resulting in kmemleak reports such as
the following:
Cc: Andre Przywara <andre.przywara@arm.com> Fixes: 1085fdc68c60 ("KVM: arm64: vgic-its: Introduce new KVM ITS device") Signed-off-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There are several scenarios that keyboard can NOT wake up system
from suspend, e.g., if a keyboard is depressed between system
device suspend phase and device noirq suspend phase, the keyboard
ISR will be called and both keyboard depress and release interrupts
will be disabled, then keyboard will no longer be able to wake up
system. Another scenario would be, if a keyboard is kept depressed,
and then system goes into suspend, the expected behavior would be
when keyboard is released, system will be waked up, but current
implementation can NOT achieve that, because both depress and release
interrupts are disabled in ISR, and the event check is still in
progress.
To fix these issues, need to make sure keyboard's depress or release
interrupt is enabled after noirq device suspend phase, this patch
moves the suspend/resume callback to noirq suspend/resume phase, and
enable the corresponding interrupt according to current keyboard status.
It was observed that multicast packets were no longer received after
a device reset. The fix is to resend the current multicast list to
the backing device after recovery.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
During frame reception while the MCAN is in Error Passive state and the
Receive Error Counter has thevalue MCAN_ECR.REC = 127, it may happen
that MCAN_IR.MRAF is set although there was no Message RAM access
failure. If MCAN_IR.MRAF is enabled, an interrupt to the Host CPU is
generated.
Work around:
The Message RAM Access Failure interrupt routine needs to check whether
MCAN_ECR.RP = '1' and MCAN_ECR.REC = '127'.
In this case, reset MCAN_IR.MRAF. No further action is required.
This affects versions older than 3.2.0
Errata explained on Sama5d2 SoC which includes this hardware block:
http://ww1.microchip.com/downloads/en/DeviceDoc/SAMA5D2-Family-Silicon-Errata-and-Data-Sheet-Clarification-DS80000803B.pdf
chapter 6.2
Reproducibility: If 2 devices with m_can are connected back to back,
configuring different bitrate on them will lead to interrupt storm on
the receiving side, with error "Message RAM access failure occurred".
Another way is to have a bad hardware connection. Bad wire connection
can lead to this issue as well.
This patch fixes the issue according to provided workaround.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In the error handling code of iwl_req_fw_callback(), iwl_dealloc_ucode()
is called to free data. In iwl_drv_stop(), iwl_dealloc_ucode() is called
again, which can cause double-free problems.
To fix this bug, the call to iwl_dealloc_ucode() in
iwl_req_fw_callback() is deleted.
This bug is found by a runtime fuzzing tool named FIZZER written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
ifmsh->csa is an RCU-protected pointer. The writer context
in ieee80211_mesh_finish_csa() is already mutually
exclusive with wdev->sdata.mtx, but the RCU checker did
not know this. Use rcu_dereference_protected() to avoid a
warning.
fixes the following warning:
[ 12.519089] =============================
[ 12.520042] WARNING: suspicious RCU usage
[ 12.520652] 5.1.0-rc7-wt+ #16 Tainted: G W
[ 12.521409] -----------------------------
[ 12.521972] net/mac80211/mesh.c:1223 suspicious rcu_dereference_check() usage!
[ 12.522928] other info that might help us debug this:
[ 12.523984] rcu_scheduler_active = 2, debug_locks = 1
[ 12.524855] 5 locks held by kworker/u8:2/152:
[ 12.525438] #0: 00000000057be08c ((wq_completion)phy0){+.+.}, at: process_one_work+0x1a2/0x620
[ 12.526607] #1: 0000000059c6b07a ((work_completion)(&sdata->csa_finalize_work)){+.+.}, at: process_one_work+0x1a2/0x620
[ 12.528001] #2: 00000000f184ba7d (&wdev->mtx){+.+.}, at: ieee80211_csa_finalize_work+0x2f/0x90
[ 12.529116] #3: 00000000831a1f54 (&local->mtx){+.+.}, at: ieee80211_csa_finalize_work+0x47/0x90
[ 12.530233] #4: 00000000fd06f988 (&local->chanctx_mtx){+.+.}, at: ieee80211_csa_finalize_work+0x51/0x90
Signed-off-by: Thomas Pedersen <thomas@eero.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
According to the AD7150 configuration register description, bit 7 assumes
value 1 when the threshold mode is fixed and 0 when it is adaptive,
however, the operation that identifies this mode was considering the
opposite values.
This patch renames the boolean variable to describe it correctly and
properly replaces it in the places where it is used.
Backlog work for psock (sk_psock_backlog) might sleep while waiting
for memory to free up when sending packets. However, while sleeping
the socket may be closed and removed from the map by the user space
side.
This breaks an assumption in sk_stream_wait_memory, which expects the
wait queue to be still there when it wakes up resulting in a
use-after-free shown below. To fix his mark sendmsg as MSG_DONTWAIT
to avoid the sleep altogether. We already set the flag for the
sendpage case but we missed the case were sendmsg is used.
Sockmap is currently the only user of skb_send_sock_locked() so only
the sockmap paths should be impacted.
==================================================================
BUG: KASAN: use-after-free in remove_wait_queue+0x31/0x70
Write of size 8 at addr ffff888069a0c4e8 by task kworker/0:2/110
Fixes: 20bf50de3028c ("skbuff: Function to send an skbuf on a socket") Reported-by: Jakub Sitnicki <jakub@cloudflare.com> Tested-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The talitos driver has two ways to perform AEAD depending on the
HW capability. Some HW support both. It is needed to give them
different names to distingish which one it is for instance when
a test fails.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Fixes: 7405c8d7ff97 ("crypto: talitos - templates for AEAD using HMAC_SNOOP_NO_AFEU") Cc: stable@vger.kernel.org Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The cacheinfo structures are alloced/freed by cpu online/offline
callbacks. Originally these were only used by sysfs to expose the
cache topology to user space. Without any in-kernel dependencies
CPUHP_AP_ONLINE_DYN was an appropriate choice.
resctrl has started using these structures to identify CPUs that
share a cache. It updates its 'domain' structures from cpu
online/offline callbacks. These depend on the cacheinfo structures
(resctrl_online_cpu()->domain_add_cpu()->get_cache_id()->
get_cpu_cacheinfo()).
These also run as CPUHP_AP_ONLINE_DYN.
Now that there is an in-kernel dependency, move the cacheinfo
work earlier so we know its done before resctrl's CPUHP_AP_ONLINE_DYN
work runs.
Fixes: 2264d9c74dda1 ("x86/intel_rdt: Build structures for each resource based on cache topology") Cc: <stable@vger.kernel.org> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: James Morse <james.morse@arm.com> Link: https://lore.kernel.org/r/20190624173656.202407-1-james.morse@arm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
cpu_to_le32/le32_to_cpu is defined in include/linux/byteorder/generic.h,
which is not exported to user-space.
UAPI headers must use the ones prefixed with double-underscore.
Detected by compile-testing exported headers:
include/linux/nilfs2_ondisk.h: In function `nilfs_checkpoint_set_snapshot':
include/linux/nilfs2_ondisk.h:536:17: error: implicit declaration of function `cpu_to_le32' [-Werror=implicit-function-declaration]
cp->cp_flags = cpu_to_le32(le32_to_cpu(cp->cp_flags) | \
^
include/linux/nilfs2_ondisk.h:552:1: note: in expansion of macro `NILFS_CHECKPOINT_FNS'
NILFS_CHECKPOINT_FNS(SNAPSHOT, snapshot)
^~~~~~~~~~~~~~~~~~~~
include/linux/nilfs2_ondisk.h:536:29: error: implicit declaration of function `le32_to_cpu' [-Werror=implicit-function-declaration]
cp->cp_flags = cpu_to_le32(le32_to_cpu(cp->cp_flags) | \
^
include/linux/nilfs2_ondisk.h:552:1: note: in expansion of macro `NILFS_CHECKPOINT_FNS'
NILFS_CHECKPOINT_FNS(SNAPSHOT, snapshot)
^~~~~~~~~~~~~~~~~~~~
include/linux/nilfs2_ondisk.h: In function `nilfs_segment_usage_set_clean':
include/linux/nilfs2_ondisk.h:622:19: error: implicit declaration of function `cpu_to_le64' [-Werror=implicit-function-declaration]
su->su_lastmod = cpu_to_le64(0);
^~~~~~~~~~~
Link: http://lkml.kernel.org/r/20190605053006.14332-1-yamada.masahiro@socionext.com Fixes: e63e88bc53ba ("nilfs2: move ioctl interface and disk layout to uapi separately") Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: Joe Perches <joe@perches.com> Cc: <stable@vger.kernel.org> [4.9+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Thinkpad t480 laptops had some touchpad features disabled, resulting in the
loss of pinch to activities in GNOME, on wayland, and other touch gestures
being slower. This patch adds the touchpad of the t480 to the smbus_pnp_ids
whitelist to enable the extra features. In my testing this does not break
suspend (on fedora, with wayland, and GNOME, using the rc-6 kernel), while
also fixing the feature on a T480.
Driver does not want to keep packets in Tx queue when link is lost.
But present code only reset NIC to flush them, but does not prevent
queuing new packets. Moreover reset sequence itself could generate
new packets via netconsole and NIC falls into endless reset loop.
This patch wakes Tx queue only when NIC is ready to send packets.
This is proper fix for problem addressed by commit 0f9e980bf5ee
("e1000e: fix cyclic resets at link up with active tx").
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Suggested-by: Alexander Duyck <alexander.duyck@gmail.com> Tested-by: Joseph Yasi <joe.yasi@gmail.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Tested-by: Oleksandr Natalenko <oleksandr@redhat.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
One space is left unused in circular FIFO to differentiate
'full' and 'empty' cases. So take that in to account while
counting for the descriptors completed.
Fixes the issue reported here,
https://lkml.org/lkml/2019/6/18/669
scripts/package/builddeb calls "make dtbs_install" after executing
a plain make (i.e. no build targets specified). It will fail if dtbs
were not built beforehand. Match the arm64 architecture where DTBs get
built by the "all" target.
Since commit 10a68cdf10 (nfsd: fix performance-limiting session
calculation) (Linux 5.1-rc1 and 4.19.31), shares from NFS servers with
1 TB of memory cannot be mounted anymore. The mount just hangs on the
client.
The gist of commit 10a68cdf10 is the change below.
`total_avail` is 8,434,659,328 on the 1 TB machine. `clamp_t()` casts
the values to `int`, which for 32-bit integers can only hold values
−2,147,483,648 (−2^31) through 2,147,483,647 (2^31 − 1).
`avail` (in the function signature) is just 65536, so that no overflow
was happening. Before the commit the assignment would result in 21845,
and `num = 4`.
When using `total_avail`, it is causing the assignment to be 18446744072226137429 (printed as %lu), and `num` is then 4164608182.
My next guess is, that `nfsd_drc_mem_used` is then exceeded, and the
server thinks there is no memory available any more for this client.
Updating the arguments of `clamp_t()` and `min_t()` to `unsigned long`
fixes the issue.
Now, `avail = 65536` (before commit 10a68cdf10 `avail = 21845`), but
`num = 4` remains the same.
Fixes: c54f24e338ed (nfsd: fix performance-limiting session calculation) Cc: stable@vger.kernel.org Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When fixing the skb leak introduced by the conversion to rbtree, I
forgot about the special case of duplicate fragments. The condition
under the 'insert_error' label isn't effective anymore as
nf_ct_frg6_gather() doesn't override the returned value anymore. So
duplicate fragments now get NF_DROP verdict.
To accept duplicate fragments again, handle them specially as soon as
inet_frag_queue_insert() reports them. Return -EINPROGRESS which will
translate to NF_STOLEN verdict, like any accepted fragment. However,
such packets don't carry any new information and aren't queued, so we
just drop them immediately.
err_spi is used when SERIAL_SC16IS7XX_SPI is enabled, so make
the label only available under SERIAL_SC16IS7XX_SPI option.
Otherwise, the below warning appears.
drivers/tty/serial/sc16is7xx.c:1523:1: warning: label ‘err_spi’ defined but not used [-Wunused-label]
err_spi:
^~~~~~~
With commit 997dd9647164 ("net: IP6 defrag: use rbtrees in
nf_conntrack_reasm.c"), nf_ct_frag6_reasm() is now called from
nf_ct_frag6_queue(). With this change, nf_ct_frag6_queue() can fail
after the skb has been added to the fragment queue and
nf_ct_frag6_gather() was adapted to handle this case.
But nf_ct_frag6_queue() can still fail before the fragment has been
queued. nf_ct_frag6_gather() can't handle this case anymore, because it
has no way to know if nf_ct_frag6_queue() queued the fragment before
failing. If it didn't, the skb is lost as the error code is overwritten
with -EINPROGRESS.
Fix this by setting -EINPROGRESS directly in nf_ct_frag6_queue(), so
that nf_ct_frag6_gather() can propagate the error as is.
Fixes: 997dd9647164 ("net: IP6 defrag: use rbtrees in nf_conntrack_reasm.c") Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fixes: d4289fcc9b16 ("net: IP6 defrag: use rbtrees for IPv6 defrag") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Stefan Bader <stefan.bader@canonical.com> Cc: Peter Oskolkov <posk@google.com> Cc: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
>> net/rds/send.c:1109:42: warning: Using plain integer as NULL pointer
Fixes: ea010070d0a7 ("net/rds: fix warn in rds_message_alloc_sgs") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The recent commit 98081ca62cba ("ALSA: hda - Record the current power
state before suspend/resume calls") made the HD-audio driver to store
the PM state in power_state field. This forgot, however, the
initialization at power up. Although the codec drivers usually don't
need to refer to this field in the normal operation, let's initialize
it properly for consistency.
Fixes: 98081ca62cba ("ALSA: hda - Record the current power state before suspend/resume calls") Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Virtual MFC codec's child devices must not be assigned to platform bus,
because they are allocated as raw 'struct device' and don't have the
corresponding 'platform' part. This fixes NULL pointer access revealed
recently by commit a66d972465d1 ("devres: Align data[] to
ARCH_KMALLOC_MINALIGN").
Fixes: c79667dd93b0 ("media: s5p-mfc: replace custom reserved memory handling code with generic one") Reported-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In commit 993107fea5ee ("mlxsw: spectrum_switchdev: Fix VLAN device
deletion via ioctl") I fixed a bug caused by the fact that the driver
views differently the deletion of a VLAN device when it is deleted via
an ioctl and netlink.
Instead of relying on a specific order of events (device being
unregistered vs. VLAN filter being updated), simply make sure that the
driver performs the necessary cleanup when the VLAN device is unlinked,
which always happens before the other two events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When something goes wrong in the GPU init after the cmdbuf suballocator
has been constructed, we fail to destroy it properly. This causes havok
later when the GPU is unbound due to a module unload or similar.
Fixes: e66774dd6f6a (drm/etnaviv: add cmdbuf suballocator) Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Tested-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This adds 4 SND_PCI_QUIRK(...) lines for several barebone models of the ODM
Clevo. The model names are written in regex syntax to describe/match all clevo
models that are similar enough and use the same PCI SSID that this fixup works
for them.
Additionally the lines regarding SSID 0x96e1 and 0x97e1 didn't fix audio for the
all our Clevo notebooks using these SSIDs (models Clevo P960* and P970*) since
ALC1220_FIXP_CLEVO_PB51ED_PINS swapped pins that are not necesarry to be
swapped. This patch initiates ALC1220_FIXUP_CLEVO_P950 instead for these model
and fixes the audio.
The devm_gpiod_request_gpiod() call will add "-gpios" to
any passed connection ID before looking it up.
I do not think the reset GPIO on this platform is named
"reset-gpios-gpios" but rather "reset-gpios" in the device
tree, so fix this up so that we get a proper reset GPIO
handle.
Also drop the inclusion of the legacy GPIO header.
When a switch event, such as tablet mode/laptop mode or docked/undocked,
wakes a device make sure that the value of the swich is reported.
Without when a device is put in tablet mode from laptop mode when it is
suspended or vice versa the device will wake up but mode will be
incorrect.
Tested by suspending a device in laptop mode and putting it in tablet
mode, the device resumes and is in tablet mode. When suspending the
device in tablet mode and putting it in laptop mode the device resumes
and is in laptop mode.
Signed-off-by: Mathew King <mathewk@chromium.org> Reviewed-by: Jett Rink <jettrink@chromium.org> Reviewed-by: Mario Limonciello <mario.limonciello@dell.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 78f3ac76d9e5 ("platform/x86: asus-wmi: Tell the EC the OS will
handle the display off hotkey") causes the backlight to be permanently off
on various EeePC laptop models using the eeepc-wmi driver (Asus EeePC
1015BX, Asus EeePC 1025C).
The asus_wmi_set_devstate(ASUS_WMI_DEVID_BACKLIGHT, 2, NULL) call added
by that commit is made conditional in this commit and only enabled in
the quirk_entry structs in the asus-nb-wmi driver fixing the broken
display / backlight on various EeePC laptop models.
Cc: João Paulo Rechi Vita <jprvita@endlessm.com> Fixes: 78f3ac76d9e5 ("platform/x86: asus-wmi: Tell the EC the OS will handle the display off hotkey") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
num_pipes is used for mutex created in mtk_drm_crtc_create(). If we
don't clear num_pipes count, when rebinding driver, the count will
be accumulated. From mtk_disp_mutex_get(), there can only be at most
10 mutex id. Clear this number so it starts from 0 in every rebind.
Fixes: 119f5173628a ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.") Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org> Signed-off-by: CK Hu <ck.hu@mediatek.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Unbinding components (i.e. mtk_dsi and mtk_disp_ovl/rdma/color) will
trigger master(mtk_drm)'s .unbind(), and currently mtk_drm's unbind
won't actually unbind components. During the next bind,
mtk_drm_kms_init() is called, and the components are added back.
.unbind() should call mtk_drm_kms_deinit() to unbind components.
And since component_master_del() in .remove() will trigger .unbind(),
which will also unregister device, it's fine to remove original functions
called here.
Fixes: 119f5173628a ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.") Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org> Signed-off-by: CK Hu <ck.hu@mediatek.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It is possible for an irq triggered by channel0 to be received later
after clks are disabled once firmware loaded during sdma probe. If
that happens then clearing them by writing to SDMA_H_INTR won't work
and the kernel will hang processing infinite interrupts. Actually,
don't need interrupt triggered on channel0 since it's pollling
SDMA_H_STATSTOP to know channel0 done rather than interrupt in
current code, just clear BD_INTR to disable channel0 interrupt to
avoid the above case.
This issue was brought by commit 1d069bfa3c78 ("dmaengine: imx-sdma:
ack channel 0 IRQ in the interrupt handler") which didn't take care
the above case.
Fixes: 1d069bfa3c78 ("dmaengine: imx-sdma: ack channel 0 IRQ in the interrupt handler") Cc: stable@vger.kernel.org #5.0+ Signed-off-by: Robin Gong <yibin.gong@nxp.com> Reported-by: Sven Van Asbroeck <thesven73@gmail.com> Tested-by: Sven Van Asbroeck <thesven73@gmail.com> Reviewed-by: Michael Olbrich <m.olbrich@pengutronix.de> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add a missing EHB (Execution Hazard Barrier) in mtc0 -> mfc0 sequence.
Without this execution hazard barrier it's possible for the value read
back from the KScratch register to be the value from before the mtc0.
Reproducible on P5600 & P6600.
The hazard is documented in the MIPS Architecture Reference Manual Vol.
III: MIPS32/microMIPS32 Privileged Resource Architecture (MD00088), rev
6.03 table 8.1 which includes:
The bounds check used the uninitialized variable vaddr, it should use
the given parameter kaddr instead. When using the uninitialized value
the compiler assumed it to be 0 and optimized this function to just
return 0 in all cases.
This should make the function check the range of the given address and
only do the page map check in case it is in the expected range of
virtual addresses.
The DRC appears to be effectively empty after an RPC/RDMA transport
reconnect. The problem is that each connection uses a different
source port, which defeats the DRC hash.
Clients always have to disconnect before they send retransmissions
to reset the connection's credit accounting, thus every retransmit
on NFS/RDMA will miss the DRC.
An NFS/RDMA client's IP source port is meaningless for RDMA
transports. The transport layer typically sets the source port value
on the connection to a random ephemeral port. The server already
ignores it for the "secure port" check. See commit 16e4d93f6de7
("NFSD: Ignore client's source port on RDMA transports").
The Linux NFS server's DRC resolves XID collisions from the same
source IP address by using the checksum of the first 200 bytes of
the RPC call header.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Cc: stable@vger.kernel.org # v4.14+ Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
| Background:
|
| In preparation of supporting IPI shorthands I changed the CPU offline
| code to software disable the local APIC instead of just masking it.
| That's done by clearing the APIC_SPIV_APIC_ENABLED bit in the APIC_SPIV
| register.
|
| Failure:
|
| When the CPU comes back online the startup code triggers occasionally
| the warning in apic_pending_intr_clear(). That complains that the IRRs
| are not empty.
|
| The offending vector is the local APIC timer vector who's IRR bit is set
| and stays set.
|
| It took me quite some time to reproduce the issue locally, but now I can
| see what happens.
|
| It requires apicv_enabled=0, i.e. full apic emulation. With apicv_enabled=1
| (and hardware support) it behaves correctly.
|
| Here is the series of events:
|
| Guest CPU
|
| goes down
|
| native_cpu_disable()
|
| apic_soft_disable();
|
| play_dead()
|
| ....
|
| startup()
|
| if (apic_enabled())
| apic_pending_intr_clear() <- Not taken
|
| enable APIC
|
| apic_pending_intr_clear() <- Triggers warning because IRR is stale
|
| When this happens then the deadline timer or the regular APIC timer -
| happens with both, has fired shortly before the APIC is disabled, but the
| interrupt was not serviced because the guest CPU was in an interrupt
| disabled region at that point.
|
| The state of the timer vector ISR/IRR bits:
|
| ISR IRR
| before apic_soft_disable() 0 1
| after apic_soft_disable() 0 1
|
| On startup 0 1
|
| Now one would assume that the IRR is cleared after the INIT reset, but this
| happens only on CPU0.
|
| Why?
|
| Because our CPU0 hotplug is just for testing to make sure nothing breaks
| and goes through an NMI wakeup vehicle because INIT would send it through
| the boots-trap code which is not really working if that CPU was not
| physically unplugged.
|
| Now looking at a real world APIC the situation in that case is:
|
| ISR IRR
| before apic_soft_disable() 0 1
| after apic_soft_disable() 0 1
|
| On startup 0 0
|
| Why?
|
| Once the dying CPU reenables interrupts the pending interrupt gets
| delivered as a spurious interupt and then the state is clear.
|
| While that CPU0 hotplug test case is surely an esoteric issue, the APIC
| emulation is still wrong, Even if the play_dead() code would not enable
| interrupts then the pending IRR bit would turn into an ISR .. interrupt
| when the APIC is reenabled on startup.
From SDM 10.4.7.2 Local APIC State After It Has Been Software Disabled
* Pending interrupts in the IRR and ISR registers are held and require
masking or handling by the CPU.
In Thomas's testing, hardware cpu will not respect soft disable LAPIC
when IRR has already been set or APICv posted-interrupt is in flight,
so we can skip soft disable APIC checking when clearing IRR and set ISR,
continue to respect soft disable APIC when attempting to set IRR.
Reported-by: Rong Chen <rong.a.chen@intel.com> Reported-by: Feng Tang <feng.tang@intel.com> Reported-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Thomas Gleixner <tglx@linutronix.de> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Rong Chen <rong.a.chen@intel.com> Cc: Feng Tang <feng.tang@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Wanpeng Li <wanpengli@tencent.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Make the forward declaration actually match the real function
definition, something that previous versions of gcc had just ignored.
This is another patch to fix new warnings from gcc-9 before I start the
merge window pulls. I don't want to miss legitimate new warnings just
because my system update brought a new compiler with new warnings.
This patch will check the weight and exit the loop if we exceeds the
weight. This is useful for preventing scsi kthread from hogging cpu
which is guest triggerable.
This addresses CVE-2019-3900.
Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Stefan Hajnoczi <stefanha@redhat.com> Fixes: 057cbf49a1f0 ("tcm_vhost: Initial merge for vhost level target fabric driver") Signed-off-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Balbir Singh <sblbir@amzn.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch will check the weight and exit the loop if we exceeds the
weight. This is useful for preventing vsock kthread from hogging cpu
which is guest triggerable. The weight can help to avoid starving the
request from on direction while another direction is being processed.
The value of weight is picked from vhost-net.
This addresses CVE-2019-3900.
Cc: Stefan Hajnoczi <stefanha@redhat.com> Fixes: 433fc58e6bf2 ("VSOCK: Introduce vhost_vsock.ko") Signed-off-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Balbir Singh <sblbir@amzn.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the rx buffer is too small for a packet, we will discard the vq
descriptor and retry it for the next packet:
while ((sock_len = vhost_net_rx_peek_head_len(net, sock->sk,
&busyloop_intr))) {
...
/* On overrun, truncate and discard */
if (unlikely(headcount > UIO_MAXIOV)) {
iov_iter_init(&msg.msg_iter, READ, vq->iov, 1, 1);
err = sock->ops->recvmsg(sock, &msg,
1, MSG_DONTWAIT | MSG_TRUNC);
pr_debug("Discarded rx packet: len %zd\n", sock_len);
continue;
}
...
}
This makes it possible to trigger a infinite while..continue loop
through the co-opreation of two VMs like:
1) Malicious VM1 allocate 1 byte rx buffer and try to slow down the
vhost process as much as possible e.g using indirect descriptors or
other.
2) Malicious VM2 generate packets to VM1 as fast as possible
Fixing this by checking against weight at the end of RX and TX
loop. This also eliminate other similar cases when:
- userspace is consuming the packets in the meanwhile
- theoretical TOCTOU attack if guest moving avail index back and forth
to hit the continue after vhost find guest just add new buffers
This addresses CVE-2019-3900.
Fixes: d8316f3991d20 ("vhost: fix total length when packets are too short") Fixes: 3a4d5c94e9593 ("vhost_net: a kernel-level virtio server") Signed-off-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Balbir Singh <sblbir@amzn.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>