Gianluca Anzolin [Tue, 27 Aug 2013 16:28:46 +0000 (18:28 +0200)]
Bluetooth: don't release the port in rfcomm_dev_state_change()
When the dlc is closed, rfcomm_dev_state_change() tries to release the
port in the case it cannot get a reference to the tty. However this is
racy and not even needed.
Infact as Peter Hurley points out:
1. Only consider dlcs that are 'stolen' from a connected socket, ie.
reused. Allocated dlcs cannot have been closed prior to port
activate and so for these dlcs a tty reference will always be avail
in rfcomm_dev_state_change() -- except for the conditions covered by
#2b below.
2. If a tty was at some point previously created for this rfcomm, then
either
(a) the tty reference is still avail, so rfcomm_dev_state_change()
will perform a hangup. So nothing to do, or,
(b) the tty reference is no longer avail, and the tty_port will be
destroyed by the last tty_port_put() in rfcomm_tty_cleanup.
Again, no action required.
3. Prior to obtaining the dlc lock in rfcomm_dev_add(),
rfcomm_dev_state_change() will not 'see' a rfcomm_dev so nothing to
do here.
4. After releasing the dlc lock in rfcomm_dev_add(),
rfcomm_dev_state_change() will 'see' an incomplete rfcomm_dev if a
tty reference could not be obtained. Again, the best thing to do here
is nothing. Any future attempted open() will block on
rfcomm_dev_carrier_raised(). The unconnected device will exist until
released by ioctl(RFCOMMRELEASEDEV).
The patch removes the aforementioned code and uses the
tty_port_tty_hangup() helper to hangup the tty.
1) If the local_df boolean is set on an SKB we have to allocate a
unique ID even if IP_DF is set in the ipv4 headers, from Ansis
Atteka.
2) Some fixups for the new chipset support that went into the sfc
driver, from Ben Hutchings.
3) Because SCTP bypasses a good chunk of, and actually duplicates, the
logic of the ipv6 output path, some IPSEC things don't get done
properly. Integrate SCTP better into the ipv6 output path so that
these problems are fixed and such issues don't get missed in the
future either. From Daniel Borkmann.
4) Fix skge regressions added by the DMA mapping error return checking
added in v3.10, from Mikulas Patocka.
5) Kill some more IRQF_DISABLED references, from Michael Opdenacker.
6) Fix races and deadlocks in the bridging code, from Hong Zhiguo.
7) Fix error handling in tun_set_iff(), in particular don't leak
resources. From Jason Wang.
8) Prevent format-string injection into xen-netback driver, from Kees
Cook.
9) Fix regression added to netpoll ARP packet handling, in particular
check for the right ETH_P_ARP protocol code. From Sonic Zhang.
10) Try to deal with AMD IOMMU errors when using r8169 chips, from
Francois Romieu.
11) Cure freezes due to recent changes in the rt2x00 wireless driver,
from Stanislaw Gruszka.
12) Don't do SPI transfers (which can sleep) in interrupt context in
cw1200 driver, from Solomon Peachy.
13) Fix LEDs handling bug in 5720 tg3 chips already handled for 5719.
From Nithin Sujir.
14) Make xen_netbk_count_skb_slots() count the actual number of slots
that will be used, taking into consideration packing and other
issues that the transmit path will run into. From David Vrabel.
15) Use the correct maximum age when calculating the bridge
message_age_timer, from Chris Healy.
16) Get rid of memory leaks in mcs7780 IRDA driver, from Alexey
Khoroshilov.
17) Netfilter conntrack extensions were converted to RCU but are not
always freed properly using kfree_rcu(). Fix from Michal Kubecek.
18) VF reset recovery not being done correctly in qlcnic driver, from
Manish Chopra.
19) Fix inverted test in ATM nicstar driver, from Andy Shevchenko.
20) Missing workqueue destroy in cxgb4 error handling, from Wei Yang.
21) Internal switch not initialized properly in bgmac driver, from Rafał
Miłecki.
22) Netlink messages report wrong local and remote addresses in IPv6
tunneling, from Ding Zhi.
23) ICMP redirects should not generate socket errors in DCCP and SCTP.
We're still working out how this should be handled for RAW and UDP
sockets. From Daniel Borkmann and Duan Jiong.
24) We've had several bugs wherein the network namespace's loopback
device gets accessed after it is free'd, NULL it out so that we can
catch these problems more readily. From Eric W Biederman.
25) Fix regression in TCP RTO calculations, from Neal Cardwell.
26) Fix too early free of xen-netback network device when VIFs still
exist. From Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
netconsole: fix a deadlock with rtnl and netconsole's mutex
netpoll: fix NULL pointer dereference in netpoll_cleanup
skge: fix broken driver
ip: generate unique IP identificator if local fragmentation is allowed
ip: use ip_hdr() in __ip_make_skb() to retrieve IP header
xen-netback: Don't destroy the netdev until the vif is shut down
net:dccp: do not report ICMP redirects to user space
cnic: Fix crash in cnic_bnx2x_service_kcq()
bnx2x, cnic, bnx2i, bnx2fc: Fix bnx2i and bnx2fc regressions.
vxlan: Avoid creating fdb entry with NULL destination
tcp: fix RTO calculated from cached RTT
drivers: net: phy: cicada.c: clears warning Use #include <linux/io.h> instead of <asm/io.h>
net loopback: Set loopback_dev to NULL when freed
batman-adv: set the TAG flag for the vid passed to BLA
netfilter: nfnetlink_queue: use network skb for sequence adjustment
net: sctp: rfc4443: do not report ICMP redirects to user space
net: usb: cdc_ether: use usb.h macros whenever possible
net: usb: cdc_ether: fix checkpatch errors and warnings
net: usb: cdc_ether: Use wwan interface for Telit modules
ip6_tunnels: raddr and laddr are inverted in nl msg
...
netconsole: fix a deadlock with rtnl and netconsole's mutex
This bug was introduced by commit 7a163bfb7ce50895bbe67300ea610d31b9c09230 ("netconsole: avoid a crash with
multiple sysfs writers"). In store_enabled() we have the following
sequence: acquire nt->mutex then rtnl, but in the netconsole netdev
notifier we have rtnl then nt->mutex effectively leading to a deadlock.
The NULL pointer dereference that the above commit tries to fix is
actually due to another bug in netpoll_cleanup(). This is fixed by dropping
the mutex from the netdev notifier as it's already protected by rtnl.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netpoll: fix NULL pointer dereference in netpoll_cleanup
I've been hitting a NULL ptr deref while using netconsole because the
np->dev check and the pointer manipulation in netpoll_cleanup are done
without rtnl and the following sequence happens when having a netconsole
over a vlan and we remove the vlan while disabling the netconsole:
CPU 1 CPU2
removes vlan and calls the notifier
enters store_enabled(), calls
netdev_cleanup which checks np->dev
and then waits for rtnl
executes the netconsole netdev
release notifier making np->dev
== NULL and releases rtnl
continues to dereference a member of
np->dev which at this point is == NULL
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The patch 136d8f377e1575463b47840bc5f1b22d94bf8f63 broke the skge driver.
Note this part of the patch:
+ if (skge_rx_setup(skge, e, nskb, skge->rx_buf_size) < 0) {
+ dev_kfree_skb(nskb);
+ goto resubmit;
+ }
+
pci_unmap_single(skge->hw->pdev,
dma_unmap_addr(e, mapaddr),
dma_unmap_len(e, maplen),
PCI_DMA_FROMDEVICE);
skb = e->skb;
prefetch(skb->data);
- skge_rx_setup(skge, e, nskb, skge->rx_buf_size);
The function skge_rx_setup modifies e->skb to point to the new skb. Thus,
after this change, the new buffer, not the old, is returned to the
networking stack.
This bug is present in kernels 3.11, 3.11.1 and 3.12-rc1. The patch should
be queued for 3.11-stable.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Reported-by: Mikulas Patocka <mpatocka@redhat.com> Reported-by: Vasiliy Glazov <vascom2@gmail.com> Tested-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ip: generate unique IP identificator if local fragmentation is allowed
If local fragmentation is allowed, then ip_select_ident() and
ip_select_ident_more() need to generate unique IDs to ensure
correct defragmentation on the peer.
For example, if IPsec (tunnel mode) has to encrypt large skbs
that have local_df bit set, then all IP fragments that belonged
to different ESP datagrams would have used the same identificator.
If one of these IP fragments would get lost or reordered, then
peer could possibly stitch together wrong IP fragments that did
not belong to the same datagram. This would lead to a packet loss
or data corruption.
Signed-off-by: Ansis Atteka <aatteka@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Durrant [Tue, 17 Sep 2013 16:46:08 +0000 (17:46 +0100)]
xen-netback: Don't destroy the netdev until the vif is shut down
Without this patch, if a frontend cycles through states Closing
and Closed (which Windows frontends need to do) then the netdev
will be destroyed and requires re-invocation of hotplug scripts
to restore state before the frontend can move to Connected. Thus
when udev is not in use the backend gets stuck in InitWait.
With this patch, the netdev is left alone whilst the backend is
still online and is only de-registered and freed just prior to
destroying the vif (which is also nicely symmetrical with the
netdev allocation and registration being done during probe) so
no re-invocation of hotplug scripts is required.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Wei Liu <wei.liu2@citrix.com> Cc: Ian Campbell <ian.campbell@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
- Minor updates and fixes to the Octeon ethernet driver in staging
- A fix to VGA_MAP_MEM() for 64 bit platforms
- Fix a workaround for 74K/1074K processors
- The symlink arch/mips/boot/dts/include/dt-bindings was pointing to a
a file with a name ending in \n. I think this may have been caused
by a git bug with with patches sent by email
- A build fix for VGA console on BCM1480-based systems
- Fix PCI device access via "/sys/bus/pci/.../resource0" or similar
work for Alchemy platforms
- Fix potential data leak on MIPS R5 cores. This doesn't add proper
support for any R5 features, just ensures a kernel without such
support will be secure to run
- Adding a macros for the CP0 Config5 register to be used by the R5 fix
- Make get_cycles() actually return something useful where possible
This also requires a preparatory patch for performance sake
- Fix a warning about the use of smp_processor_id() in preemptible
code. Again this includes a preparatory patch adding the
infrastructure to be used by the actual patch
- Finally remove pointless one-line comment
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix invalid symbolic link file
MIPS: PCI: pci-bcm1480: Include missing vt.h header
MIPS: Disable usermode switching of the FR bit for MIPS R5 CPUs.
MIPS: Add MIPS R5 config5 register.
MIPS: PCI: Use pci_resource_to_user to map pci memory space properly
MIPS: 74K/1074K: Correct erratum workaround.
MIPS: Cleanup CP0 PRId and CP1 FPIR register access masks
MIPS: Remove useless comment about kprobe from arch/mips/Makefile
MIPS: Fix VGA_MAP_MEM macro.
MIPS: Reimplement get_cycles().
MIPS: Optimize current_cpu_type() for better code.
MIPS: Fix accessing to per-cpu data when flushing the cache
MIPS: Provide nice way to access boot CPU's data.
staging: octeon-ethernet: rgmii: enable interrupts that we can handle
staging: octeon-ethernet: remove skb alloc failure warnings
staging: octeon-ethernet: make dropped packets to consume NAPI budget
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull ceph fixes from Sage Weil:
"These fix several bugs with RBD from 3.11 that didn't get tested in
time for the merge window: some error handling, a use-after-free, and
a sequencing issue when unmapping and image races with a notify
operation.
There is also a patch fixing a problem with the new ceph + fscache
code that just went in"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
fscache: check consistency does not decrement refcount
rbd: fix error handling from rbd_snap_name()
rbd: ignore unmapped snapshots that no longer exist
rbd: fix use-after free of rbd_dev->disk
rbd: make rbd_obj_notify_ack() synchronous
rbd: complete notifies before cleaning up osd_client and rbd_dev
libceph: add function to ensure notifies are complete
Commit 3b29aa5ba204c [MIPS: add <dt-bindings/> symlink] created a symlink
file in include/dt-bindings. Even though commit diff is fine, the symlink
is invalid and ls -lb shows a newline character at the end of the filename:
lrwxrwxrwx 1 maddy maddy 35 Sep 19 18:11 dt-bindings ->
../../../../../include/dt-bindings\n
MIPS: PCI: pci-bcm1480: Include missing vt.h header
It's needed for the MAX_NR_CONSOLES macro.
Fixes the following build problem on a randconfig:
arch/mips/pci/pci-bcm1480.c: In function 'bcm1480_pcibios_init':
arch/mips/pci/pci-bcm1480.c:261:36: error: 'MAX_NR_CONSOLES'
undeclared (first use in this function)
arch/mips/pci/pci-bcm1480.c:261:36: note: each undeclared
identifier is reported only once for each function it appears in
make[1]: *** [arch/mips/pci/pci-bcm1480.o] Error 1
MIPS: Disable usermode switching of the FR bit for MIPS R5 CPUs.
Currently the kernel will always use the FR=0 register model for O32. If
an O32 application did enable FR=1 mode, some data from another application
might be leaked in the extra registers becoming visible.
Iow, this patch is meant to make the kernel MIPS R5 tolerant but leaves
proper MIPS R5 support to a future patchset.
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm radeon/nouveau/core fixes from Dave Airlie:
"Mostly radeon fixes, with some nouveau bios parser, ttm fix and a fix
for AST driver"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (42 commits)
drm/fb-helper: don't sleep for screen unblank when an oops is in progress
drm, ttm Fix uninitialized warning
drm/ttm: fix the tt_populated check in ttm_tt_destroy()
drm/nouveau/ttm: prevent double-free in nouveau_sgdma_create_ttm() failure path
drm/nouveau/bios/init: fix thinko in INIT_CONFIGURE_MEM
drm/nouveau/kms: enable for non-vga pci classes
drm/nouveau/bios/init: stub opcode 0xaa
drm/radeon: avoid UVD corruptions on AGP cards
drm/radeon: fix panel scaling with eDP and LVDS bridges
drm/radeon/dpm: rework auto performance level enable
drm/radeon: Fix hmdi typo
drm/radeon/dpm/rs780: fix force_performance state for same sclks
drm/radeon/dpm/rs780: don't enable sclk scaling if not required
drm/radeon/dpm/rs780: add some sanity checking to sclk scaling
drm/radeon/dpm/rs780: use drm_mode_vrefresh()
drm/udl: rip out set_need_resched
drm/ast: fix the ast open key function
drm/radeon/dpm: add bapm callback for kb/kv
drm/radeon/dpm: add bapm callback for trinity
drm/radeon/dpm: add infrastructure to properly handle bapm
...
Daniel Vetter [Fri, 13 Sep 2013 21:49:57 +0000 (14:49 -0700)]
drm/fb-helper: don't sleep for screen unblank when an oops is in progress
Otherwise the system will burn even brighter and worse, leave the user
wondering what's going on exactly.
Since we already have a panic handler which will (try) to restore the
entire fbdev console mode, we can just bail out. Inspired by a patch from
Konstantin Khlebnikov. The callchain leading to this, cut&pasted from
Konstantin's original patch:
Note that the entire locking in the fb helper around panic/sysrq and kdbg
is ... non-existant. So we have a decent change of blowing up
everything. But since reworking this ties in with funny concepts like the
fbdev notifier chain or the impressive things which happen around
console_lock while oopsing, I'll leave that as an exercise for braver
souls than me.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Konstantin Khlebnikov <khlebnikov@openvz.org> Cc: Dave Airlie <airlied@gmail.com> Reviewed-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/ttm/ttm_object.c: In function ‘ttm_base_object_lookup’:
drivers/gpu/drm/ttm/ttm_object.c:213:10: error: ‘base’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
kref_put(&base->refcount, ttm_release_base);
^
drivers/gpu/drm/ttm/ttm_object.c:221:26: note: ‘base’ was declared here
struct ttm_base_object *base;
Signed-off-by: Prarit Bhargava <prarit@redhat.com> Reviewed-by: Rob Clark <robdclark@gmail.com> Reviewed-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ben Skeggs [Tue, 17 Sep 2013 04:21:15 +0000 (14:21 +1000)]
drm/ttm: fix the tt_populated check in ttm_tt_destroy()
After a vmalloc failure in ttm_dma_tt_alloc_page_directory(),
ttm_dma_tt_init() will call ttm_tt_destroy() to cleanup, and end up
inside the driver's unpopulate() hook when populate() has never yet
been called.
On nouveau, the first issue to be hit because of this is that
dma_address[] may be a NULL pointer. After working around this,
ttm_pool_unpopulate() may potentially hit the same issue with
the pages[] array.
It seems to make more sense to avoid calling unpopulate on already
unpopulated TTMs than to add checks to all the implementations.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Cc: stable@vger.kernel.org Cc: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 19 Sep 2013 01:47:23 +0000 (11:47 +1000)]
Merge branch 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
A couple of bios parser fixes (one for ancient chips, another for new ones - important in Optimus configs). Another to make sure KMS is enabled on certain Optimus configs, and a TTM failure path fix.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/ttm: prevent double-free in nouveau_sgdma_create_ttm() failure path
drm/nouveau/bios/init: fix thinko in INIT_CONFIGURE_MEM
drm/nouveau/kms: enable for non-vga pci classes
drm/nouveau/bios/init: stub opcode 0xaa
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"atomic_open-related fixes (Miklos' series, with EEXIST-related parts
replaced with fix in fs/namei.c:atomic_open() instead of messing with
the instances) + race fix in autofs + leak on failure exit in 9p"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
9p: don't forget to destroy inode cache if fscache registration fails
atomic_open: take care of EEXIST in no-open case with O_CREAT|O_EXCL in fs/namei.c
vfs: don't set FILE_CREATED before calling ->atomic_open()
nfs: set FILE_CREATED
gfs2: set FILE_CREATED
cifs: fix filp leak in cifs_atomic_open()
vfs: improve i_op->atomic_open() documentation
autofs4: close the races around autofs4_notify_daemon()
Make sure 74K revision numbers are not applied to the 1074K. Also catch
invalid usage.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5857/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Merge tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull pstore/compression fixes from Tony Luck:
"Three pstore fixes related to compression:
1) Better adjustment of size of compression buffer (was too big for
EFIVARS backend resulting in compression failure
2) Use zlib_inflateInit2 instead of zlib_inflateInit
3) Don't print messages about compression failure. They will waste
space that may better be used to log console output leading to the
crash"
* tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
pstore: Remove the messages related to compression failure
pstore: Use zlib_inflateInit2 instead of zlib_inflateInit
pstore: Adjust buffer size for compression for smaller registered buffers
Johan Hedberg [Fri, 13 Sep 2013 05:58:18 +0000 (08:58 +0300)]
Bluetooth: Fix rfkill functionality during the HCI setup stage
We need to let the setup stage complete cleanly even when the HCI device
is rfkilled. Otherwise the HCI device will stay in an undefined state
and never get notified to user space through mgmt (even when it gets
unblocked through rfkill).
This patch makes sure that hci_dev_open() can be called in the HCI_SETUP
stage, that blocking the device doesn't abort the setup stage, and that
the device gets proper powered down as soon as the setup stage completes
in case it was blocked meanwhile.
The bug that this patch fixed can be very easily reproduced using e.g.
the rfkill command line too. By running "rfkill block all" before
inserting a Bluetooth dongle the resulting HCI device goes into a state
where it is never announced over mgmt, not even when "rfkill unblock all"
is run.
Johan Hedberg [Fri, 13 Sep 2013 05:58:17 +0000 (08:58 +0300)]
Bluetooth: Introduce a new HCI_RFKILLED flag
This makes it more convenient to check for rfkill (no need to check for
dev->rfkill before calling rfkill_blocked()) and also avoids potential
races if the RFKILL state needs to be checked from within the rfkill
callback.
net:dccp: do not report ICMP redirects to user space
DCCP shouldn't be setting sk_err on redirects as it
isn't an error condition. it should be doing exactly
what tcp is doing and leaving the error handler without
touching the socket.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel/lpss: Add pin control support to Intel low power subsystem
perf/x86/intel: Mark MEM_LOAD_UOPS_MISS_RETIRED as precise on SNB
x86: Remove now-unused save_rest()
x86/smpboot: Fix announce_cpu() to printk() the last "OK" properly
changed the code to use the bnx2x macro NO_FCOE() to determine if FCoE
is supported or not. There is another place in cnic that is still using
the old method to determine if FCoE is supported or not. The 2 methods
may not yield the same result after the network interface is brought down
and up. This will cause the crash as cnic_bnx2x_service_kcq() will access
the uninitialized cp->kcq2.
The fix is to consistently use the same macro CNIC_SUPPORTS_FCOE() which
uses the bnx2x NO_FCOE() macro. As a follow-up, we can clean up the code
to remove the old method as it is no longer needed.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
changed the configuration of the doorbell HW and it broke iSCSI and FCoE.
We fix this by making compatible changes to the doorbell address in bnx2i
and bnx2fc. For the userspace driver, we need to pass a modified CID
so that the existing userspace driver will calculate the correct doorbell
address and continue to work.
Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eddie Wai <eddie.wai@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix comment for sched_info_depart
sched/Documentation: Update sched-design-CFS.txt documentation
sched/debug: Take PID namespace into account
sched/fair: Fix small race where child->se.parent,cfs_rq might point to invalid ones
Leonid Yegoshin [Wed, 11 Sep 2013 00:36:04 +0000 (19:36 -0500)]
MIPS: Fix VGA_MAP_MEM macro.
Use the CKSEG1ADDR macro when calculating VGA_MAP_MEM.
[ralf@linux-mips.org: Include <asm/addrspace.h for CKSEG1ADDR.]
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com> Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5814/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This essentially reverts commit efb9ca08b5a2374b29938cdcab417ce4feb14b54
(kernel.org) / 58020a106879a8b372068741c81f0015c9b0b96dbv [[MIPS] Change
get_cycles to always return 0.]
Most users of get_cycles() invoke it as a timing interface. That's why
in modern kernels it was never very much missed for. /dev/random however
uses get_cycles() in the how the jitter in the interrupt timing contains
some useful entropy.
Merge branch 'fixes' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Gleb Natapov.
* 'fixes' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: set "blocked by NMI" flag if EPT violation happens during IRET from NMI
kvm: free resources after canceling async_pf
KVM: nEPT: reset PDPTR register cache on nested vmentry emulation
KVM: mmu: allow page tables to be in read-only slots
KVM: x86 emulator: emulate RETF imm
Starting from v3.10 (probably commit f91e2590410b: "tty: Signal
foreground group processes in hangup") disassociate_ctty() sends SIGCONT
if tty && on_exit. This breaks LSB test-suite, in particular test8 in
_exit.c and test40 in sigcon5.c.
Put the "!on_exit" check back to restore the old behaviour.
Review by Peter Hurley:
"Yes, this regression was introduced by me in that commit. The effect
of the regression is that ptys will receive a SIGCONT when, in similar
circumstances, ttys would not.
The fact that two test vectors accidentally tripped over this
regression suggests that some other apps may as well.
Thanks for catching this"
Cc: stable@vger.kernel.org # v3.10+ Signed-off-by: Oleg Nesterov <oleg@redhat.com> Reported-by: Karel Srot <ksrot@redhat.com> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
vxlan: Avoid creating fdb entry with NULL destination
Commit afbd8bae9c798c5cdbe4439d3a50536b5438247c
vxlan: add implicit fdb entry for default destination
creates an implicit fdb entry for default destination. This results
in an invalid fdb entry if default destination is not specified.
For ex:
ip link add vxlan1 type vxlan id 100
creates the following fdb entry
00:00:00:00:00:00 dev vxlan1 dst 0.0.0.0 self permanent
This patch fixes this issue by creating an fdb entry only if a
valid default destination is specified.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1b7fdd2ab5852 ("tcp: do not use cached RTT for RTT estimation")
did not correctly account for the fact that crtt is the RTT shifted
left 3 bits. Fix the calculation to consistently reflect this fact.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Yuchung Cheng <ycheng@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Acked-By: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It has recently turned up that we have a number of long standing bugs
in the network stack cleanup code with use of the loopback device
after it has been freed that have not turned up because in most cases
the storage allocated to the loopback device is not reused, when those
accesses happen.
Set looback_dev to NULL to trigger oopses instead of silent data corrupt
when we hit this class of bug.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
batman-adv: set the TAG flag for the vid passed to BLA
When receiving or sending a packet a packet on a VLAN, the
vid has to be marked with the TAG flag in order to make any
component in batman-adv understand that the packet is coming
from a really tagged network.
This fix the Bridge Loop Avoidance behaviour which was not
able to send announces over VLAN interfaces.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.org> Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
MIPS: Optimize current_cpu_type() for better code.
o Move current_cpu_type() to a separate header file
o #ifdefing on supported CPU types lets modern GCC know that certain
code in callers may be discarded ideally turning current_cpu_type() into
a function returning a constant.
o Use current_cpu_type() rather than direct access to struct cpuinfo_mips.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5833/
Caches in most systems are identical - but not always, so we can't avoid
the use of smp_call_function() by just looking at the boot CPU's data,
have to fiddle with preemption instead.
Pull more tile architecture updates from Chris Metcalf:
"This second batch of changes is just cleanup of various kinds from
doing some tidying work in the sources.
Some dead code is removed, comment typos fixed, whitespace and style
issues cleaned up, and some header updates from our internal
"upstream" architecture team"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: remove stray blank space
tile: <arch/> header updates from upstream
tile: improve gxio iorpc autogenerated code style
tile: double default VMALLOC space
tile: remove stale arch/tile/kernel/futex_64.S
tile: remove HUGE_VMAP dead code
tile: use pmd_pfn() instead of casting via pte_t
tile: fix typos in comment in arch/tile/kernel/unaligned.c
boot_cpu_data is used the same as current_cpu_data but returns the CPU
data for CPU 0. This means it doesn't have to use smp_processor_id()
thus no need to disable preemption.
When we cancel 'async_pf_execute()', we should behave as if the work was
never scheduled in 'kvm_setup_async_pf()'.
Fixes a bug when we can't unload module because the vm wasn't destroyed.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Gleb Natapov <gleb@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: nEPT: reset PDPTR register cache on nested vmentry emulation
After nested vmentry stale cache can be used to reload L2 PDPTR pointers
which will cause L2 guest to fail. Fix it by invalidating cache on nested
vmentry emulation.
https://bugzilla.kernel.org/show_bug.cgi?id=60830
Signed-off-by: Gleb Natapov <gleb@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Mon, 9 Sep 2013 11:52:33 +0000 (13:52 +0200)]
KVM: mmu: allow page tables to be in read-only slots
Page tables in a read-only memory slot will currently cause a triple
fault because the page walker uses gfn_to_hva and it fails on such a slot.
OVMF uses such a page table; however, real hardware seems to be fine with
that as long as the accessed/dirty bits are set. Save whether the slot
is readonly, and later check it when updating the accessed and dirty bits.
Aaro Koskinen [Thu, 5 Sep 2013 18:44:01 +0000 (21:44 +0300)]
staging: octeon-ethernet: rgmii: enable interrupts that we can handle
Enable only those interrupts that we can handle & acknowledge in the
interrupt handler.
At least on EdgeRouter Lite, the hardware may occasionally interrupt with
some error condition when the physical link status changes frequently.
Since the interrupt condition is not acked properly, this leads to the
following warning and the IRQ gets disabled completely:
Remove skb allocation failure warnings. They will trigger a page
allocation warning already. Also, one of the warnings was not ratelimited,
causing the box to lock up under heavy traffic & low memory.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by: David Daney <david.daney@cavium.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: devel@driverdev.osuosl.org Cc: linux-mips@linux-mips.org Cc: Jason A. Donenfeld <Jason@zx2c4.com> Cc: richard@nod.at Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Patchwork: https://patchwork.linux-mips.org/patch/5811/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David S. Miller [Tue, 17 Sep 2013 01:42:37 +0000 (21:42 -0400)]
Merge branch 'sfc-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/bwh/sfc
Ben Hutchings says:
====================
Some bug fixes and future-proofing for the recently added SFC9120
support:
1. Minimal support for the 40G configuration.
2. Disable the incomplete PTP/hardware timestamping support.
3. Reset MAC stats properly after a firmware upgrade.
4. Re-check the datapath firmware capabilities after the controller is
reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Mon, 16 Sep 2013 10:36:02 +0000 (12:36 +0200)]
net: sctp: rfc4443: do not report ICMP redirects to user space
Adapt the same behaviour for SCTP as present in TCP for ICMP redirect
messages. For IPv6, RFC4443, section 2.4. says:
...
(e) An ICMPv6 error message MUST NOT be originated as a result of
receiving the following:
...
(e.2) An ICMPv6 redirect message [IPv6-DISC].
...
Therefore, do not report an error to user space, just invoke dst's redirect
callback and leave, same for IPv4 as done in TCP as well. The implication
w/o having this patch could be that the reception of such packets would
generate a poll notification and in worst case it could even tear down the
whole connection. Therefore, stop updating sk_err on redirects.
Reported-by: Duan Jiong <duanj.fnst@cn.fujitsu.com> Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Suggested-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: usb: cdc_ether: use usb.h macros whenever possible
Use USB_DEVICE_AND_INTERFACE_INFO and USB_VENDOR_AND_INTERFACE_INFO
macros to reduce boilerplate.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com> Acked-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: usb: cdc_ether: fix checkpatch errors and warnings
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com> Acked-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: usb: cdc_ether: Use wwan interface for Telit modules
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com> Cc: <stable@vger.kernel.org> # 3.0+ as far back as it applies cleanly Acked-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_tunnels: raddr and laddr are inverted in nl msg
IFLA_IPTUN_LOCAL and IFLA_IPTUN_REMOTE were inverted.
Introduced by c075b13098b3 (ip6tnl: advertise tunnel param via rtnl).
Signed-off-by: Ding Zhi <zhi.ding@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bgmac: implement unaligned addressing for DMA rings that support it
This is important patch for new devices that support unaligned
addressing. That devices suffer from the backward-compatibility bug in
DMA engine. In theory we should be able to use old mechanism, but in
practice DMA address seems to be randomly copied into status register
when hardware reaches end of a ring. This breaks reading slot number
from status register and we can't use DMA anymore.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch it is impossible to read et_swtype, because the 1
byte space is needed for the terminating null byte. The max expected
value is 0xF, so now it should be possible to read decimal form ("15")
and hex form ("0xF").
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices (BCM4749, BCM5357, BCM53572) have internal switch that
requires initialization. We already have code for this, but because
of the typo in code it was never working. This resulted in network not
working for some routers and possibility of soft-bricking them.
Use correct bit for switch initialization and fix typo in the define.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Olaf Hering [Fri, 13 Sep 2013 21:52:01 +0000 (14:52 -0700)]
drivers/net/ethernet/ibm/ehea/ehea_main.c: add alias entry for portN properties
Use separate table for alias entries in the ehea module, otherwise the
probe() function will operate on the separate ports instead of the
lhea-"root" entry of the device-tree
[ Thadeu notes that: "... this issue might happen with the generation of
initrd, when the scripts check for /sys/class/net/eth0/device/modalias,
which links to the port device at
/sys/devices/ibmebus/23c00400.lhea/port0/" ]
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Olaf Hering <ohering@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vfs: don't set FILE_CREATED before calling ->atomic_open()
If O_CREAT|O_EXCL are passed to open, then we know that either
- the file is successfully created, or
- the operation fails in some way.
So previously we set FILE_CREATED before calling ->atomic_open() so the
filesystem doesn't have to. This, however, led to bugs in the
implementation that went unnoticed when the filesystem didn't check for
existence, yet returned success. To prevent this kind of bug, require
filesystems to always explicitly set FILE_CREATED on O_CREAT|O_EXCL and
verify this in the VFS.
Also added a couple more verifications for the result of atomic_open():
- Warn if filesystem set FILE_CREATED despite the lack of O_CREAT.
- Warn if filesystem set FILE_CREATED but gave a negative dentry.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If an error occurs after having called finish_open() then fput() needs to
be called on the already opened file.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Cc: Steve French <sfrench@samba.org> Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fix documentation of ->atomic_open() and related functions: finish_open()
and finish_no_open(). Also add details that seem to be unclear and a
source of bugs (some of which are fixed in the following series).
Cc-ing maintainers of all filesystems implementing ->atomic_open().
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Cc: Eric Van Hensbergen <ericvh@gmail.com> Cc: Sage Weil <sage@inktank.com> Cc: Steve French <sfrench@samba.org> Cc: Steven Whitehouse <swhiteho@redhat.com> Cc: Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sat, 14 Sep 2013 21:32:12 +0000 (17:32 -0400)]
autofs4: close the races around autofs4_notify_daemon()
Don't drop ->wq_mutex before calling autofs4_notify_daemon() only to regain it
there. Besides being pointless, that opens a race window where autofs4_wait_release()
could've come and freed wq->name.name. And do the debugging printk in the "reused an
existing wq" case before dropping ->wq_mutex - the same reason...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: Ian Kent <raven@themaw.net>
Merge branch 'timers/core' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer code update from Thomas Gleixner:
- armada SoC clocksource overhaul with a trivial merge conflict
- Minor improvements to various SoC clocksource drivers
* 'timers/core' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: armada-370-xp: Add detailed clock requirements in devicetree binding
clocksource: armada-370-xp: Get reference fixed-clock by name
clocksource: armada-370-xp: Replace WARN_ON with BUG_ON
clocksource: armada-370-xp: Fix device-tree binding
clocksource: armada-370-xp: Introduce new compatibles
clocksource: armada-370-xp: Use CLOCKSOURCE_OF_DECLARE
clocksource: armada-370-xp: Simplify TIMER_CTRL register access
clocksource: armada-370-xp: Use BIT()
ARM: timer-sp: Set dynamic irq affinity
ARM: nomadik: add dynamic irq flag to the timer
clocksource: sh_cmt: 32-bit control register support
clocksource: em_sti: Convert to devm_* managed helpers
Chris Metcalf [Mon, 16 Sep 2013 18:18:21 +0000 (14:18 -0400)]
tile: <arch/> header updates from upstream
The hardware architecture descriptor headers have been updated, in
particular to reflect some larger MMIO fields on the mPIPE shims for
controlling the network hardware, from the recent Gx72 release.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Mon, 16 Sep 2013 17:02:57 +0000 (13:02 -0400)]
tile: double default VMALLOC space
With per-cpu data as well as loaded kernel modules coming from
the vmalloc arena, we get close to the line all the time and
occasionally need more than we had, so just double it up by default.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull CIFS fixes from Steve French:
"Two minor cifs fixes and a minor documentation cleanup for cifs.txt"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update cifs.txt and remove some outdated infos
cifs: Avoid calling unlock_page() twice in cifs_readpage() when using fscache
cifs: Do not take a reference to the page in cifs_readpage_worker()
Oliver Smith [Mon, 16 Sep 2013 18:30:57 +0000 (20:30 +0200)]
netfilter: ipset: Fix serious failure in CIDR tracking
This fixes a serious bug affecting all hash types with a net element -
specifically, if a CIDR value is deleted such that none of the same size
exist any more, all larger (less-specific) values will then fail to
match. Adding back any prefix with a CIDR equal to or more specific than
the one deleted will fix it.
Steps to reproduce:
ipset -N test hash:net
ipset -A test 1.1.0.0/16
ipset -A test 2.2.2.0/24
ipset -T test 1.1.1.1 #1.1.1.1 IS in set
ipset -D test 2.2.2.0/24
ipset -T test 1.1.1.1 #1.1.1.1 IS NOT in set
This is due to the fact that the nets counter was unconditionally
decremented prior to the iteration that shifts up the entries. Now, we
first check if there is a proceeding entry and if not, decrement it and
return. Otherwise, we proceed to iterate and then zero the last element,
which, in most cases, will already be zero.
Signed-off-by: Oliver Smith <oliver@8.c.9.b.0.7.4.0.1.0.0.2.ip6.arpa> Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
netfilter: ipset: Consistent userspace testing with nomatch flag
The "nomatch" commandline flag should invert the matching at testing,
similarly to the --return-nomatch flag of the "set" match of iptables.
Until now it worked with the elements with "nomatch" flag only. From
now on it works with elements without the flag too, i.e:
# ipset n test hash:net
# ipset a test 10.0.0.0/24 nomatch
# ipset t test 10.0.0.1
10.0.0.1 is NOT in set test.
# ipset t test 10.0.0.1 nomatch
10.0.0.1 is in set test.
# ipset a test 192.168.0.0/24
# ipset t test 192.168.0.1
192.168.0.1 is in set test.
# ipset t test 192.168.0.1 nomatch
192.168.0.1 is NOT in set test.
Before the patch the results were
...
# ipset t test 192.168.0.1
192.168.0.1 is in set test.
# ipset t test 192.168.0.1 nomatch
192.168.0.1 is in set test.
Syam Sidhardhan [Mon, 5 Aug 2013 16:59:12 +0000 (01:59 +0900)]
Bluetooth: Fix ACL alive for long in case of non pariable devices
For certain devices (ex: HID mouse), support for authentication,
pairing and bonding is optional. For such devices, the ACL alive
for too long after the L2CAP disconnection.
To avoid the ACL alive for too long after L2CAP disconnection, reset the
ACL disconnect timeout back to HCI_DISCONN_TIMEOUT during L2CAP connect.