mlxsw: spectrum: Clear VLAN filters during port initialization
When a port is created, its VLAN filters are not cleared by the
firmware. This causes tagged packets to be later dropped by the ingress
STP filters, which default to DISCARD state.
The above did not matter much until commit b5ce611fd96e ("mlxsw:
spectrum: Add devlink-trap support") where we exposed the drop reason to
users.
Without this patch, the drop reason users will see is not consistent. If
a port is enslaved to a VLAN-aware bridge and a packet with an invalid
VLAN tries to ingress the bridge, it will be dropped due to ingress STP
filter. If the VLAN is later enabled and then disabled, the packet will
be dropped by the ingress VLAN filter despite the above being a
seemingly NOP operation.
Fix this by clearing all the VLAN filters during port initialization.
Adjust the test accordingly.
Fixes: b5ce611fd96e ("mlxsw: spectrum: Add devlink-trap support") Reported-by: Alex Kushnarov <alexanderk@mellanox.com> Tested-by: Alex Kushnarov <alexanderk@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hans Andersson [Thu, 26 Sep 2019 07:54:37 +0000 (09:54 +0200)]
net: phy: micrel: add Asym Pause workaround for KSZ9021
The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
Pause capability is set. This issue is described in a Silicon Errata
(DS80000691D or DS80000692D), which advises to always disable the
capability.
Micrel KSZ9021 has no errata, but has the same issue with Asymmetric Pause.
This patch apply the same workaround as the one for KSZ9031.
Fixes: 3aed3e2a143c ("net: phy: micrel: add Asym Pause workaround") Signed-off-by: Hans Andersson <hans.andersson@cellavision.se> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Thu, 26 Sep 2019 02:28:19 +0000 (19:28 -0700)]
ptp: correctly disable flags on old ioctls
Commit 415606588c61 ("PTP: introduce new versions of IOCTLs",
2019-09-13) introduced new versions of the PTP ioctls which actually
validate that the flags are acceptable values.
As part of this, it cleared the flags value using a bitwise
and+negation, in an attempt to prevent the old ioctl from accidentally
enabling new features.
This is incorrect for a couple of reasons. First, it results in
accidentally preventing previously working flags on the request ioctl.
By clearing the "valid" flags, we now no longer allow setting the
enable, rising edge, or falling edge flags.
Second, if we add new additional flags in the future, they must not be
set by the old ioctl. (Since the flag wasn't checked before, we could
potentially break userspace programs which sent garbage flag data.
The correct way to resolve this is to check for and clear all but the
originally valid flags.
Create defines indicating which flags are correctly checked and
interpreted by the original ioctls. Use these to clear any bits which
will not be correctly interpreted by the original ioctls.
In the future, new flags must be added to the VALID_FLAGS macros, but
*not* to the V1_VALID_FLAGS macros. In this way, new features may be
exposed over the v2 ioctls, but without breaking previous userspace
which happened to not clear the flags value properly. The old ioctl will
continue to behave the same way, while the new ioctl gains the benefit
of using the flags fields.
Cc: Richard Cochran <richardcochran@gmail.com> Cc: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: David S. Miller <davem@davemloft.net> Cc: Christopher Hall <christopher.s.hall@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Vasut [Wed, 25 Sep 2019 22:08:42 +0000 (00:08 +0200)]
net: dsa: microchip: Always set regmap stride to 1
The regmap stride is set to 1 for regmap describing 8bit registers already.
However, for 16/32/64bit registers, the stride is 2/4/8 respectively. This
is not correct, as the switch protocol supports unaligned register reads
and writes and the KSZ87xx even uses such unaligned register accesses to
read e.g. MIB counter.
This patch fixes MIB counter access on KSZ87xx.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andrew Lunn <andrew@lunn.ch> Cc: David S. Miller <davem@davemloft.net> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: George McCollister <george.mccollister@gmail.com> Cc: Tristram Ha <Tristram.Ha@microchip.com> Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Cc: Woojung Huh <woojung.huh@microchip.com> Fixes: 46558d601cb6 ("net: dsa: microchip: Initial SPI regmap support") Fixes: 255b59ad0db2 ("net: dsa: microchip: Factor out regmap config generation into common header") Reviewed-by: George McCollister <george.mccollister@gmail.com> Tested-by: George McCollister <george.mccollister@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following patchset contains Netfilter fixes for net:
1) Add NFT_CHAIN_POLICY_UNSET to replace hardcoded -1 to
specify that the chain policy is unset. The chain policy
field is actually defined as an 8-bit unsigned integer.
2) Remove always true condition reported by smatch in
chain policy check.
3) Fix element lookup on dynamic sets, from Florian Westphal.
4) Use __u8 in ebtables uapi header, from Masahiro Yamada.
5) Bogus EBUSY when removing flowtable after chain flush,
from Laura Garcia Liebana.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
nfp: flower: fix memory leak in nfp_flower_spawn_vnic_reprs
In nfp_flower_spawn_vnic_reprs in the loop if initialization or the
allocations fail memory is leaked. Appropriate releases are added.
Fixes: b94524529741 ("nfp: flower: add per repr private data for LAG offload") Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
nfp: flower: prevent memory leak in nfp_flower_spawn_phy_reprs
In nfp_flower_spawn_phy_reprs, in the for loop over eth_tbl if any of
intermediate allocations or initializations fail memory is leaked.
requiered releases are added.
Fixes: b94524529741 ("nfp: flower: add per repr private data for LAG offload") Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey [Wed, 25 Sep 2019 15:02:35 +0000 (18:02 +0300)]
net/sched: Set default of CONFIG_NET_TC_SKB_EXT to N
This a new feature, it is preferred that it defaults to N.
We will probe the feature support from userspace before actually using it.
Fixes: 95a7233c452a ('net: openvswitch: Set OvS recirc_id from tc chain index') Signed-off-by: Paul Blakey <paulb@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 25 Sep 2019 14:53:19 +0000 (07:53 -0700)]
vrf: Do not attempt to create IPv6 mcast rule if IPv6 is disabled
A user reported that vrf create fails when IPv6 is disabled at boot using
'ipv6.disable=1':
https://bugzilla.kernel.org/show_bug.cgi?id=204903
The failure is adding fib rules at create time. Add RTNL_FAMILY_IP6MR to
the check in vrf_fib_rule if ipv6_mod_enabled is disabled.
Fixes: e4a38c0c4b27 ("ipv6: add vrf table handling code for ipv6 mcast") Signed-off-by: David Ahern <dsahern@gmail.com> Cc: Patrick Ruddy <pruddy@vyatta.att-mail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 27 Sep 2019 10:13:55 +0000 (12:13 +0200)]
Merge branch 'qdisc-destroy'
Vlad Buslov says:
====================
Fix Qdisc destroy issues caused by adding fine-grained locking to filter API
TC filter API unlocking introduced several new fine-grained locks. The
change caused sleeping-while-atomic BUGs in several Qdiscs that call cls
APIs which need to obtain new mutex while holding sch tree spinlock. This
series fixes affected Qdiscs by ensuring that cls API that became sleeping
is only called outside of sch tree lock critical section.
====================
Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: sched: sch_sfb: don't call qdisc_put() while holding tree lock
Recent changes that removed rtnl dependency from rules update path of tc
also made tcf_block_put() function sleeping. This function is called from
ops->destroy() of several Qdisc implementations, which in turn is called by
qdisc_put(). Some Qdiscs call qdisc_put() while holding sch tree spinlock,
which results sleeping-while-atomic BUG.
Steps to reproduce for sfb:
tc qdisc add dev ens1f0 handle 1: root sfb
tc qdisc add dev ens1f0 parent 1:10 handle 50: sfq perturb 10
tc qdisc change dev ens1f0 root handle 1: sfb
In sfb_change() function use qdisc_purge_queue() instead of
qdisc_tree_flush_backlog() to properly reset old child Qdisc and save
pointer to it into local temporary variable. Put reference to Qdisc after
sch tree lock is released in order not to call potentially sleeping cls API
in atomic section. This is safe to do because Qdisc has already been reset
by qdisc_purge_queue() inside sch tree lock critical section.
Reported-by: syzbot+ac54455281db908c581e@syzkaller.appspotmail.com Fixes: c266f64dbfa2 ("net: sched: protect block state with mutex") Suggested-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: sched: multiq: don't call qdisc_put() while holding tree lock
Recent changes that removed rtnl dependency from rules update path of tc
also made tcf_block_put() function sleeping. This function is called from
ops->destroy() of several Qdisc implementations, which in turn is called by
qdisc_put(). Some Qdiscs call qdisc_put() while holding sch tree spinlock,
which results sleeping-while-atomic BUG.
Rearrange locking in multiq_tune() in following ways:
- In loop that removes Qdiscs from disabled queues, call
qdisc_purge_queue() instead of qdisc_tree_flush_backlog() on Qdisc that
is being destroyed. Save the Qdisc in temporary allocated array and call
qdisc_put() on each element of the array after sch tree lock is released.
This is safe to do because Qdiscs have already been reset by
qdisc_purge_queue() inside sch tree lock critical section.
- Do the same change for second loop that initializes Qdiscs for newly
enabled queues in multiq_tune() function. Since sch tree lock is obtained
and released on each iteration of this loop, just call qdisc_put()
directly outside of critical section. Don't verify that old Qdisc is not
noop_qdisc before releasing reference to it because such check is already
performed by qdisc_put*() functions.
Fixes: c266f64dbfa2 ("net: sched: protect block state with mutex") Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: sched: sch_htb: don't call qdisc_put() while holding tree lock
Recent changes that removed rtnl dependency from rules update path of tc
also made tcf_block_put() function sleeping. This function is called from
ops->destroy() of several Qdisc implementations, which in turn is called by
qdisc_put(). Some Qdiscs call qdisc_put() while holding sch tree spinlock,
which results sleeping-while-atomic BUG.
Steps to reproduce for htb:
tc qdisc add dev ens1f0 root handle 1: htb default 12
tc class add dev ens1f0 parent 1: classid 1:1 htb rate 100kbps ceil 100kbps
tc qdisc add dev ens1f0 parent 1:1 handle 40: sfq perturb 10
tc class add dev ens1f0 parent 1:1 classid 1:2 htb rate 100kbps ceil 100kbps
In htb_change_class() function save parent->leaf.q to local temporary
variable and put reference to it after sch tree lock is released in order
not to call potentially sleeping cls API in atomic section. This is safe to
do because Qdisc has already been reset by qdisc_purge_queue() inside sch
tree lock critical section.
Fixes: c266f64dbfa2 ("net: sched: protect block state with mutex") Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In rds_bind(), laddr_check is called without checking if it is NULL or
not. And rs_transport should be reset if rds_add_bound() fails.
Fixes: c5c1a030a7db ("net/rds: An rds_sock is added too early to the hash table") Reported-by: syzbot+fae39afd2101a17ec624@syzkaller.appspotmail.com Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 27 Sep 2019 10:05:02 +0000 (12:05 +0200)]
Merge branch 'SO_PRIORITY'
Eric Dumazet says:
====================
tcp: provide correct skb->priority
SO_PRIORITY socket option requests TCP egress packets
to contain a user provided value.
TCP manages to send most packets with the requested values,
notably for TCP_ESTABLISHED state, but fails to do so for
few packets.
These packets are control packets sent on behalf
of SYN_RECV or TIME_WAIT states.
Note that to test this with packetdrill, it is a bit
of a hassle, since packetdrill can not verify priority
of egress packets, other than indirect observations,
using for example sch_prio on its tunnel device.
The bad skb priorities cause problems for GCP,
as this field is one of the keys used in routing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 24 Sep 2019 15:01:16 +0000 (08:01 -0700)]
tcp: honor SO_PRIORITY in TIME_WAIT state
ctl packets sent on behalf of TIME_WAIT sockets currently
have a zero skb->priority, which can cause various problems.
In this patch we :
- add a tw_priority field in struct inet_timewait_sock.
- populate it from sk->sk_priority when a TIME_WAIT is created.
- For IPv4, change ip_send_unicast_reply() and its two
callers to propagate tw_priority correctly.
ip_send_unicast_reply() no longer changes sk->sk_priority.
- For IPv6, make sure TIME_WAIT sockets pass their tw_priority
field to tcp_v6_send_response() and tcp_v6_send_ack().
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 24 Sep 2019 15:01:14 +0000 (08:01 -0700)]
ipv6: add priority parameter to ip6_xmit()
Currently, ip6_xmit() sets skb->priority based on sk->sk_priority
This is not desirable for TCP since TCP shares the same ctl socket
for a given netns. We want to be able to send RST or ACK packets
with a non zero skb->priority.
This patch has no functional change.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Zhang [Wed, 25 Sep 2019 23:43:12 +0000 (16:43 -0700)]
bpf: Fix bpf_event_output re-entry issue
BPF_PROG_TYPE_SOCK_OPS program can reenter bpf_event_output because it
can be called from atomic and non-atomic contexts since we don't have
bpf_prog_active to prevent it happen.
This patch enables 3 levels of nesting to support normal, irq and nmi
context.
We can easily reproduce the issue by running netperf crr mode with 100
flows and 10 threads from netperf client side.
Fixes: a5a3a828cd00 ("bpf: add perf event notificaton support for sock_ops") Signed-off-by: Allan Zhang <allanzhang@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Stanislav Fomichev <sdf@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20190925234312.94063-2-allanzhang@google.com
Andrew Lunn [Wed, 25 Sep 2019 00:47:07 +0000 (02:47 +0200)]
net: dsa: qca8k: Fix port enable for CPU port
The CPU port does not have a PHY connected to it. So calling
phy_support_asym_pause() results in an Opps. As with other DSA
drivers, add a guard that the port is a user port.
Reported-by: Michal Vokáč <michal.vokac@ysoft.com> Fixes: 0394a63acfe2 ("net: dsa: enable and disable all ports") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Michal Vokáč <michal.vokac@ysoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: a2c11b034142 ("kcm: use BPF_PROG_RUN") Fixes: 6cab5e90ab2b ("bpf: run bpf programs with preemption disabled") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 25 Sep 2019 11:05:54 +0000 (14:05 +0300)]
net: ethernet: stmmac: Fix signedness bug in ipq806x_gmac_of_parse()
The "gmac->phy_mode" variable is an enum and in this context GCC will
treat it as an unsigned int so the error handling will never be
triggered.
Fixes: b1c17215d718 ("stmmac: add ipq806x glue layer") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 25 Sep 2019 11:05:24 +0000 (14:05 +0300)]
net: nixge: Fix a signedness bug in nixge_probe()
The "priv->phy_mode" is an enum and in this context GCC will treat it
as an unsigned int so it can never be less than zero.
Fixes: 492caffa8a1a ("net: ethernet: nixge: Add support for National Instruments XGE netdev") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 25 Sep 2019 11:01:00 +0000 (14:01 +0300)]
of: mdio: Fix a signedness bug in of_phy_get_and_connect()
The "iface" variable is an enum and in this context GCC treats it as
an unsigned int so the error handling is never triggered.
Fixes: b78624125304 ("of_mdio: Abstract a general interface for phy connect") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 25 Sep 2019 10:59:11 +0000 (13:59 +0300)]
net: axienet: fix a signedness bug in probe
The "lp->phy_mode" is an enum but in this context GCC treats it as an
unsigned int so the error handling is never triggered.
Fixes: ee06b1728b95 ("net: axienet: add support for standard phy-mode binding") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 25 Sep 2019 10:58:22 +0000 (13:58 +0300)]
net: stmmac: dwmac-meson8b: Fix signedness bug in probe
The "dwmac->phy_mode" is an enum and in this context GCC treats it as
an unsigned int so the error handling is never triggered.
Fixes: 566e82516253 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 25 Sep 2019 10:57:14 +0000 (13:57 +0300)]
enetc: Fix a signedness bug in enetc_of_get_phy()
The "priv->if_mode" is type phy_interface_t which is an enum. In this
context GCC will treat the enum as an unsigned int so this error
handling is never triggered.
Fixes: d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 25 Sep 2019 10:56:38 +0000 (13:56 +0300)]
net: netsec: Fix signedness bug in netsec_probe()
The "priv->phy_interface" variable is an enum and in this context GCC
will treat it as an unsigned int so the error handling is never
triggered.
Fixes: 533dd11a12f6 ("net: socionext: Add Synquacer NetSec driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 25 Sep 2019 10:56:04 +0000 (13:56 +0300)]
net: broadcom/bcmsysport: Fix signedness in bcm_sysport_probe()
The "priv->phy_interface" variable is an enum and in this context GCC
will treat it as unsigned so the error handling will never be
triggered.
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 25 Sep 2019 10:55:32 +0000 (13:55 +0300)]
net: hisilicon: Fix signedness bug in hix5hd2_dev_probe()
The "priv->phy_mode" variable is an enum and in this context GCC will
treat it as unsigned to the error handling will never trigger.
Fixes: 57c5bc9ad7d7 ("net: hisilicon: add hix5hd2 mac driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 25 Sep 2019 10:54:59 +0000 (13:54 +0300)]
cxgb4: Signedness bug in init_one()
The "chip" variable is an enum, and it's treated as unsigned int by GCC
in this context so the error handling isn't triggered.
Fixes: e8d452923ae6 ("cxgb4: clean up init_one") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 25 Sep 2019 10:54:30 +0000 (13:54 +0300)]
net: aquantia: Fix aq_vec_isr_legacy() return value
The irqreturn_t type is an enum or an unsigned int in GCC. That
creates to problems because it can't detect if the
self->aq_hw_ops->hw_irq_read() call fails and at the end the function
always returns IRQ_HANDLED.
drivers/net/ethernet/aquantia/atlantic/aq_vec.c:316 aq_vec_isr_legacy() warn: unsigned 'err' is never less than zero.
drivers/net/ethernet/aquantia/atlantic/aq_vec.c:329 aq_vec_isr_legacy() warn: always true condition '(err >= 0) => (0-u32max >= 0)'
Fixes: 970a2e9864b0 ("net: ethernet: aquantia: Vector operations") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
According to Tal Gilboa the only benefit from DIM comes from a driver
that uses it. So it doesn't make sense to make this symbol user visible,
instead all drivers that use it should select it (as is already the case
AFAICT).
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
libbpf: Teach btf_dumper to emit stand-alone anonymous enum definitions
BTF-to-C converter previously skipped anonymous enums in an assumption
that those are embedded in struct's field definitions. This is not
always the case and a lot of kernel constants are defined as part of
anonymous enums. This change fixes the logic by eagerly marking all
types as either referenced by any other type or not. This is enough to
distinguish two classes of anonymous enums and emit previously omitted
enum definitions.
ipv6: do not free rt if FIB_LOOKUP_NOREF is set on suppress rule
Commit 7d9e5f422150 removed references from certain dsts, but accounting
for this never translated down into the fib6 suppression code. This bug
was triggered by WireGuard users who use wg-quick(8), which uses the
"suppress-prefix" directive to ip-rule(8) for routing all of their
internet traffic without routing loops. The test case added here
causes the reference underflow by causing packets to evaluate a suppress
rule.
Fixes: 7d9e5f422150 ("ipv6: convert major tx path to use RT6_LOOKUP_F_DST_NOREF") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Acked-by: Wei Wang <weiwan@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Tue, 24 Sep 2019 11:11:52 +0000 (19:11 +0800)]
openvswitch: change type of UPCALL_PID attribute to NLA_UNSPEC
userspace openvswitch patch "(dpif-linux: Implement the API
functions to allow multiple handler threads read upcall)"
changes its type from U32 to UNSPEC, but leave the kernel
unchanged
and after kernel 6e237d099fac "(netlink: Relax attr validation
for fixed length types)", this bug is exposed by the below
warning
[ 57.215841] netlink: 'ovs-vswitchd': attribute type 5 has an invalid length.
Fixes: 5cd667b0a456 ("openvswitch: Allow each vport to have an array of 'port_id's") Signed-off-by: Li RongQing <lirongqing@baidu.com> Acked-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Biju Das [Mon, 23 Sep 2019 13:32:46 +0000 (14:32 +0100)]
dt-bindings: net: ravb: Add support for r8a774b1 SoC
Document RZ/G2N (R8A774B1) SoC bindings.
Signed-off-by: Biju Das <biju.das@bp.renesas.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The size of individual pages in the page pool in given by an order. The
order is the binary logarithm of the number of pages that make up one of
the pages in the pool. However, the driver currently passes the number
of pages rather than the order, so it ends up wasting quite a bit of
memory.
Fix this by taking the binary logarithm and passing that in the order
field.
Fixes: 2af6106ae949 ("net: stmmac: Introducing support for Page Pool") Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The issue was caused by skb's true_size changed without its sk's
sk_wmem_alloc increased in tcp/skb_gro_receive(). Later when the
skb is being freed and the skb's truesize is subtracted from its
sk's sk_wmem_alloc in tcp_wfree(), underflow occurs.
macsec is calling gro_cells_receive() to receive a packet, which
actually requires skb->sk to be NULL. However when macsec dev is
over veth, it's possible the skb->sk is still set if the skb was
not unshared or expanded from the peer veth.
ip_rcv() is calling skb_orphan() to drop the skb's sk for tproxy,
but it is too late for macsec's calling gro_cells_receive(). So
fix it by dropping the skb's sk earlier on rx path of macsec.
Fixes: 5491e7c6b1a9 ("macsec: enable GRO and RPS on macsec devices") Reported-by: Xiumei Mu <xmu@redhat.com> Reported-by: Fei Liu <feliu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched: cbs: Fix not adding cbs instance to list
When removing a cbs instance when offloading is enabled, the crash
below can be observed.
The problem happens because that when offloading is enabled, the cbs
instance is not added to the list.
Also, the current code doesn't handle correctly the case when offload
is disabled without removing the qdisc: if the link speed changes the
credit calculations will be wrong. When we create the cbs instance
with offloading enabled, it's not added to the notification list, when
later we disable offloading, it's not in the list, so link speed
changes will not affect it.
The solution for both issues is the same, add the cbs instance being
created unconditionally to the global list, even if the link state
notification isn't useful "right now".
Fixes: e0a7683d30e9 ("net/sched: cbs: fix port_rate miscalculation") Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Kalle Valo <kvalo@codeaurora.org> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Rain River [Mon, 23 Sep 2019 14:37:46 +0000 (22:37 +0800)]
MAINTAINERS: add Yanjun to FORCEDETH maintainers list
Yanjun has been spending quite a lot of time fixing bugs
in FORCEDETH source code. I'd like to add Yanjun to maintainers
list.
Signed-off-by: Rain River <rain.1986.08.12@gmail.com> Acked-by: Zhu Yanjun <yanjun.zhu@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
selftests/bpf: adjust strobemeta loop to satisfy latest clang
Some recent changes in latest Clang started causing the following
warning when unrolling strobemeta test case main loop:
progs/strobemeta.h:416:2: warning: loop not unrolled: the optimizer was
unable to perform the requested transformation; the transformation might
be disabled or specified as part of an unsupported transformation
ordering [-Wpass-failed=transform-warning]
This patch simplifies loop's exit condition to depend only on constant
max iteration number (STROBE_MAX_MAP_ENTRIES), while moving early
termination logic inside the loop body. The changes are equivalent from
program logic standpoint, but fixes the warning. It also appears to
improve generated BPF code, as it fixes previously failing non-unrolled
strobemeta test cases.
Some compilers emit warning for potential uninitialized next_id usage.
The code is correct, but control flow is too complicated for some
compilers to figure this out. Re-initialize next_id to satisfy
compiler.
Signed-off-by: Andrii Nakryiko <andriin@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jonathan Lemon [Tue, 24 Sep 2019 16:25:21 +0000 (09:25 -0700)]
bpf/xskmap: Return ERR_PTR for failure case instead of NULL.
When kzalloc() failed, NULL was returned to the caller, which
tested the pointer with IS_ERR(), which didn't match, so the
pointer was used later, resulting in a NULL dereference.
Return ERR_PTR(-ENOMEM) instead of NULL.
Reported-by: syzbot+491c1b7565ba9069ecae@syzkaller.appspotmail.com Fixes: 0402acd683c6 ("xsk: remove AF_XDP socket from map when the socket is released") Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com> Acked-by: Björn Töpel <bjorn.topel@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
selftests/bpf: test_progs: fix client/server race in tcp_rtt
This is the same problem I found earlier in test_sockopt_inherit:
there is a race between server thread doing accept() and client
thread doing connect(). Let's explicitly synchronize them via
pthread conditional variable.
v2:
* don't exit from server_thread without signaling condvar,
fixes possible issue where main() would wait forever (Andrii Nakryiko)
Fixes: b55873984dab ("selftests/bpf: test BPF_SOCK_OPS_RTT_CB") Signed-off-by: Stanislav Fomichev <sdf@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
macb_64b_desc is always called when HW_DMA_CAP_64B is defined.
So the return NULL can never be reached. Remove the dead code.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Mon, 23 Sep 2019 07:49:08 +0000 (09:49 +0200)]
net: stmmac: selftests: Flow Control test can also run with ASYM Pause
The Flow Control selftest is also available with ASYM Pause. Lets add
this check to the test and fix eventual false positive failures.
Fixes: 091810dbded9 ("net: stmmac: Introduce selftests support") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes two fixes. The first improves reset code to allow
linkwatch_event to proceed during reset. The second ensures that no more
than one thread runs in reset at a time.
v2:
- Separate change param reset from do_reset()
- Return IBMVNIC_OPEN_FAILED if __ibmvnic_open fails
- Remove setting wait_for_reset to false from __ibmvnic_reset(), this
is done in wait_for_reset()
- Move the check for force_reset_recovery from patch 1 to patch 2
v3:
- Restore reset’s successful return in open failure case
v4:
- Change resetting flag access to atomic
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Juliet Kim [Fri, 20 Sep 2019 20:11:23 +0000 (16:11 -0400)]
net/ibmvnic: prevent more than one thread from running in reset
The current code allows more than one thread to run in reset. This can
corrupt struct adapter data. Check adapter->resetting before performing
a reset, if there is another reset running delay (100 msec) before trying
again.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Juliet Kim [Fri, 20 Sep 2019 20:11:22 +0000 (16:11 -0400)]
net/ibmvnic: unlock rtnl_lock in reset so linkwatch_event can run
Commit a5681e20b541 ("net/ibmnvic: Fix deadlock problem in reset")
made the change to hold the RTNL lock during a reset to avoid deadlock
but linkwatch_event is fired during the reset and needs the RTNL lock.
That keeps linkwatch_event process from proceeding until the reset
is complete. The reset process cannot tolerate the linkwatch_event
processing after reset completes, so release the RTNL lock during the
process to allow a chance for linkwatch_event to run during reset.
This does not guarantee that the linkwatch_event will be processed as
soon as link state changes, but is an improvement over the current code
where linkwatch_event processing is always delayed, which prevents
transmissions on the device from being deactivated leading transmit
watchdog timer to time-out.
Release the RTNL lock before link state change and re-acquire after
the link state change to allow linkwatch_event to grab the RTNL lock
and run during the reset.
Fixes: a5681e20b541 ("net/ibmnvic: Fix deadlock problem in reset") Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: nf_tables: bogus EBUSY when deleting flowtable after flush
The deletion of a flowtable after a flush in the same transaction
results in EBUSY. This patch adds an activation and deactivation of
flowtables in order to update the _use_ counter.
Signed-off-by: Laura Garcia Liebana <nevola@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: ebtables: use __u8 instead of uint8_t in uapi header
When CONFIG_UAPI_HEADER_TEST=y, exported headers are compile-tested to
make sure they can be included from user-space.
Currently, linux/netfilter_bridge/ebtables.h is excluded from the test
coverage. To make it join the compile-test, we need to fix the build
errors attached below.
For a case like this, we decided to use __u{8,16,32,64} variable types
in this discussion:
https://lkml.org/lkml/2019/6/5/18
Build log:
CC usr/include/linux/netfilter_bridge/ebtables.h.s
In file included from <command-line>:32:0:
./usr/include/linux/netfilter_bridge/ebtables.h:126:4: error: unknown type name ‘uint8_t’
uint8_t revision;
^~~~~~~
./usr/include/linux/netfilter_bridge/ebtables.h:139:4: error: unknown type name ‘uint8_t’
uint8_t revision;
^~~~~~~
./usr/include/linux/netfilter_bridge/ebtables.h:152:4: error: unknown type name ‘uint8_t’
uint8_t revision;
^~~~~~~
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Dan Carpenter [Sat, 21 Sep 2019 06:01:45 +0000 (09:01 +0300)]
wil6210: use after free in wil_netif_rx_any()
The debug code dereferences "skb" to print "skb->len" so we have to
print the message before we free "skb".
Fixes: f99fe49ff372 ("wil6210: add wil_netif_rx() helper function") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Running old skge driver on PowerPC causes checksum errors
because hardware reported 1's complement checksum is in little-endian
byte order.
Reported-by: Benoit <benoit.sansoni@gmail.com> Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
arcnet: provide a buffer big enough to actually receive packets
struct archdr is only big enough to hold the header of various types of
arcnet packets. So to provide enough space to hold the data read from
hardware provide a buffer large enough to hold a packet with maximal
size.
The problem was noticed by the stack protector which makes the kernel
oops.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
iwlwifi: fw: don't send GEO_TX_POWER_LIMIT command to FW version 36
The intention was to have the GEO_TX_POWER_LIMIT command in FW version
36 as well, but not all 8000 family got this feature enabled. The
8000 family is the only one using version 36, so skip this version
entirely. If we try to send this command to the firmwares that do not
support it, we get a BAD_COMMAND response from the firmware.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=204151.
Cc: stable@vger.kernel.org # 4.19+ Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mt7615 patch/n9/cr4 firmwares are available in mediatek folder in
linux-firmware repository. Because of this mt7615 won't work on regular
distributions like Ubuntu. Fix path definitions. Moreover remove useless
firmware name pointers and use definitions directly
Fixes: 04b8e65922f6 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets") Cc: stable@vger.kernel.org Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
David S. Miller [Tue, 24 Sep 2019 14:37:18 +0000 (16:37 +0200)]
Merge branch 'check-CAP_NEW_RAW'
Greg Kroah-Hartman says:
====================
Raw socket cleanups
Ori Nimron pointed out that there are a number of places in the kernel
where you can create a raw socket, without having to have the
CAP_NET_RAW permission.
To resolve this, here's a short patch series to test these odd and old
protocols for this permission before allowing the creation to succeed
All patches are currently against the net tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ori Nimron [Fri, 20 Sep 2019 07:35:49 +0000 (09:35 +0200)]
nfc: enforce CAP_NET_RAW for raw sockets
When creating a raw AF_NFC socket, CAP_NET_RAW needs to be checked
first.
Signed-off-by: Ori Nimron <orinimron123@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ori Nimron [Fri, 20 Sep 2019 07:35:48 +0000 (09:35 +0200)]
ieee802154: enforce CAP_NET_RAW for raw sockets
When creating a raw AF_IEEE802154 socket, CAP_NET_RAW needs to be
checked first.
Signed-off-by: Ori Nimron <orinimron123@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ori Nimron [Fri, 20 Sep 2019 07:35:47 +0000 (09:35 +0200)]
ax25: enforce CAP_NET_RAW for raw sockets
When creating a raw AF_AX25 socket, CAP_NET_RAW needs to be checked
first.
Signed-off-by: Ori Nimron <orinimron123@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ori Nimron [Fri, 20 Sep 2019 07:35:46 +0000 (09:35 +0200)]
appletalk: enforce CAP_NET_RAW for raw sockets
When creating a raw AF_APPLETALK socket, CAP_NET_RAW needs to be checked
first.
Signed-off-by: Ori Nimron <orinimron123@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ori Nimron [Fri, 20 Sep 2019 07:35:45 +0000 (09:35 +0200)]
mISDN: enforce CAP_NET_RAW for raw sockets
When creating a raw AF_ISDN socket, CAP_NET_RAW needs to be checked
first.
Signed-off-by: Ori Nimron <orinimron123@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 90b73b77d08e ("net: sched: change action API to use array of pointers to actions") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Vlad Buslov <vladbu@mellanox.com> Cc: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmytro Linkin [Fri, 13 Sep 2019 10:42:21 +0000 (10:42 +0000)]
net/mlx5e: Fix matching on tunnel addresses type
In mlx5 parse_tunnel_attr() function dispatch on encap IP address type
is performed by directly checking flow_rule_match_key() on
FLOW_DISSECTOR_KEY_ENC_IPV4_ADDRS, and then on
FLOW_DISSECTOR_KEY_ENC_IPV6_ADDRS. However, since those are stored in
union, first check is always true if any type of encap address is set,
which leads to IPv6 tunnel encap address being parsed as IPv4 by mlx5.
Determine correct IP address type by checking control key first and if
it set, take address type from match.key->addr_type.
Fixes: d1bda7eecd88 ("net/mlx5e: Allow matching only enc_key_id/enc_dst_port for decapsulation action") Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com> Reviewed-by: Vlad Buslov <vladbu@mellanox.com> Reviewed-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
net/mlx5e: Fix traffic duplication in ethtool steering
Before this patch, when adding multiple ethtool steering rules with
identical classification, the driver used to append the new destination
to the already existing hw rule, which caused the hw to forward the
traffic to all destinations (rx queues).
Here we avoid this by setting the "no append" mlx5 fs core flag when
adding a new ethtool rule.
Bodong Wang [Mon, 26 Aug 2019 21:34:12 +0000 (16:34 -0500)]
net/mlx5: Add device ID of upcoming BlueField-2
Add the device ID of upcoming BlueField-2 integrated ConnectX-6 Dx
network controller. Its VFs will be using the generic VF device ID:
0x101e "ConnectX Family mlx5Gen Virtual Function".
Fixes: 2e9d3e83ab82 ("net/mlx5: Update the list of the PCI supported devices") Signed-off-by: Bodong Wang <bodong@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Alex Vesker [Thu, 19 Sep 2019 08:24:19 +0000 (11:24 +0300)]
net/mlx5: DR, Fix getting incorrect prev node in ste_free
When we free an STE and the STE is in the middle of collision
list, the prev_ste was obtained incorrectly from the list.
To avoid such issues list_entry calls replaced with standard list API.
After firmware has been downloaded, driver should send
some information to it through H2C commands. Those H2C
commands are transmitted through TX path.
But before HCI has been started, the TX path is not
working completely. Such as PCI interfaces, the interrupts
are not enabled, hence TX interrupts will not be issued
after H2C skb has been DMAed to the device. And the H2C
skbs will not be released until the device is powered off.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
net: dsa: Use the correct style for SPDX License Identifier
This patch corrects the SPDX License Identifier style
in header file for Distributed Switch Architecture drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
net: dsa: b53: Use the correct style for SPDX License Identifier
This patch corrects the SPDX License Identifier style
in header file for Broadcom BCM53xx managed switch driver.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Mao Wenan [Sun, 22 Sep 2019 05:38:08 +0000 (13:38 +0800)]
net: ena: Select DIMLIB for ENA_ETHERNET
If CONFIG_ENA_ETHERNET=y and CONFIG_DIMLIB=n,
below erros can be found:
drivers/net/ethernet/amazon/ena/ena_netdev.o: In function `ena_dim_work':
ena_netdev.c:(.text+0x21cc): undefined reference to `net_dim_get_rx_moderation'
ena_netdev.c:(.text+0x21cc): relocation truncated to
fit: R_AARCH64_CALL26 against undefined symbol `net_dim_get_rx_moderation'
drivers/net/ethernet/amazon/ena/ena_netdev.o: In function `ena_io_poll':
ena_netdev.c:(.text+0x7bd4): undefined reference to `net_dim'
ena_netdev.c:(.text+0x7bd4): relocation truncated to fit:
R_AARCH64_CALL26 against undefined symbol `net_dim'
After commit 282faf61a053 ("net: ena: switch to dim algorithm for rx adaptive
interrupt moderation"), it introduces dim algorithm, which configured by CONFIG_DIMLIB.
So, this patch is to select DIMLIB for ENA_ETHERNET.
Fixes: 282faf61a053 ("net: ena: switch to dim algorithm for rx adaptive interrupt moderation") Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Putting a struct stmmac_rss object on the stack is a bad idea,
as it exceeds the warning limit for a stack frame on 32-bit architectures:
drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c:1221:12: error: stack frame size of 1208 bytes in function '__stmmac_test_l3filt' [-Werror,-Wframe-larger-than=]
drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c:1338:12: error: stack frame size of 1208 bytes in function '__stmmac_test_l4filt' [-Werror,-Wframe-larger-than=]
As the object is the trivial empty case, change the called function
to accept a NULL pointer to mean the same thing and remove the
large variable in the two callers.
Fixes: 4647e021193d ("net: stmmac: selftests: Add selftest for L3/L4 Filters") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Mao Wenan [Thu, 19 Sep 2019 06:38:19 +0000 (14:38 +0800)]
net: dsa: sja1105: Add dependency for NET_DSA_SJA1105_TAS
If CONFIG_NET_DSA_SJA1105_TAS=y and CONFIG_NET_SCH_TAPRIO=n,
below error can be found:
drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_setup_tc_taprio':
sja1105_tas.c:(.text+0x318): undefined reference to `taprio_offload_free'
sja1105_tas.c:(.text+0x590): undefined reference to `taprio_offload_get'
drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_tas_teardown':
sja1105_tas.c:(.text+0x610): undefined reference to `taprio_offload_free'
make: *** [vmlinux] Error 1
sja1105_tas needs tc-taprio, so this patch add the dependency for it.
Fixes: 317ab5b86c8e ("net: dsa: sja1105: Configure the Time-Aware Scheduler via tc-taprio offload") Signed-off-by: Mao Wenan <maowenan@huawei.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Cong Wang [Thu, 19 Sep 2019 01:44:43 +0000 (18:44 -0700)]
net_sched: add policy validation for action attributes
Similar to commit 8b4c3cdd9dd8
("net: sched: Add policy validation for tc attributes"), we need
to add proper policy validation for TC action attributes too.
Cc: David Ahern <dsahern@gmail.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Cong Wang [Wed, 18 Sep 2019 23:24:12 +0000 (16:24 -0700)]
net_sched: add max len check for TCA_KIND
The TCA_KIND attribute is of NLA_STRING which does not check
the NUL char. KMSAN reported an uninit-value of TCA_KIND which
is likely caused by the lack of NUL.
Change it to NLA_NUL_STRING and add a max len too.
Fixes: 8b4c3cdd9dd8 ("net: sched: Add policy validation for tc attributes") Reported-and-tested-by: syzbot+618aacd49e8c8b8486bd@syzkaller.appspotmail.com Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
projects / mirror_ubuntu-kernels.git / log