Stefan Agner [Thu, 2 Aug 2018 08:42:50 +0000 (10:42 +0200)]
net: fec: check DMA addressing limitations
Check DMA addressing limitations as suggested by the DMA API
how-to. This does not fix a particular issue seen but is
considered good style.
Signed-off-by: Stefan Agner <stefan@agner.ch> Acked-by: Fugang Duan <fugang.duan@nxp.com> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Thu, 2 Aug 2018 08:13:33 +0000 (09:13 +0100)]
rxrpc: Remove set but not used variable 'nowj'
Fixes gcc '-Wunused-but-set-variable' warning:
net/rxrpc/proc.c: In function 'rxrpc_call_seq_show':
net/rxrpc/proc.c:66:29: warning:
variable 'nowj' set but not used [-Wunused-but-set-variable]
unsigned long timeout = 0, nowj;
^
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vincent Bernat [Wed, 1 Aug 2018 20:05:10 +0000 (22:05 +0200)]
net: don't declare IPv6 non-local bind helper if CONFIG_IPV6 undefined
Fixes: 83ba4645152d ("net: add helpers checking if socket can be bound to nonlocal address") Signed-off-by: Vincent Bernat <vincent@bernat.im> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Aug 2018 18:50:55 +0000 (11:50 -0700)]
Merge tag 'rxrpc-next-20180801' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Development
Here are some patches that add some more tracepoints to AF_RXRPC and fix
some issues therein. The most significant points are:
(1) Display the call timeout information in /proc/net/rxrpc/calls.
(2) Save the call's debug_id in the rxrpc_channel struct so that it can be
used in traces after the rxrpc_call struct has been destroyed.
(3) Increase the size of the kAFS Rx window from 32 to 63 to be about the
same as the Auristor server.
(4) Propose the terminal ACK for a client call after it has received all
its data to be transmitted after a short interval so that it will get
transmitted if not first superseded by a new call on the same channel.
(5) Flush ACKs during the data reception if we detect that we've run out
of data.[*]
(6) Trace successful packet transmission and softirq to process context
socket notification.
[*] Note that on a uncontended gigabit network, rxrpc runs in to trouble
with ACK packets getting batched together (up to ~32 at a time)
somewhere between the IP transmit queue on the client and the ethernet
receive queue on the server.
I can see the kernel afs filesystem client and Auristor userspace
server stalling occasionally on a 512MB single read. Sticking
tracepoints in the network driver at either end seems to show that,
although the ACK transmissions made by the client are reasonably spaced
timewise, the received ACKs come in batches from the network card on
the server.
I'm not sure what, if anything, can be done about this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Wed, 1 Aug 2018 12:45:32 +0000 (18:15 +0530)]
cxgb4: fix endian to test F_FW_PORT_CMD_DCBXDIS32
For FW_PORT_ACTION_GET_PORT_INFO32 messages, the
u.info32.lstatus32_to_cbllen32 is 32-bit Big Endian.
We need to translate that to CPU Endian in order to
test F_FW_PORT_CMD_DCBXDIS32.
Signed-off-by: Casey Leedom <leedom@chelsio.com> Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Wed, 1 Aug 2018 10:36:56 +0000 (12:36 +0200)]
net: sched: fix notifications for action-held chains
Chains that only have action references serve as placeholders.
Until a non-action reference is created, user should not be aware
of the chain. Also he should not receive any notifications about it.
So send notifications for the new chain only in case the chain gets
the first non-action reference. Symmetrically to that, when
the last non-action reference is dropped, send the notification about
deleted chain.
Reported-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
v1->v2:
- made __tcf_chain_{get,put}() static as suggested by Cong
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Wed, 1 Aug 2018 10:36:55 +0000 (12:36 +0200)]
net: sched: change name of zombie chain to "held_by_acts_only"
As mentioned by Cong and Jakub during the review process, it is a bit
odd to sometimes (act flow) create a new chain which would be
immediately a "zombie". So just rename it to "held_by_acts_only".
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Suggested-by: Cong Wang <xiyou.wangcong@gmail.com> Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Wed, 1 Aug 2018 10:27:03 +0000 (18:27 +0800)]
net: hns3: fix return value error while hclge_cmd_csq_clean failed
While cleaning the command queue, the value of the HEAD register is not
in the range of next_to_clean and next_to_use, meaning that this value
is invalid. This also means that there is a hardware error and the
hardware will trigger a reset soon. At this time we should return an
error code instead of 0, and HCLGE_STATE_CMD_DISABLE needs to be set to
prevent sending command again.
Fixes: 3ff504908f95 ("net: hns3: fix a dead loop in hclge_cmd_csq_clean") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 1 Aug 2018 02:04:02 +0000 (10:04 +0800)]
ip_gre: remove redundant variables t_hlen
After commit ffc2b6ee4174 ("ip_gre: fix IFLA_MTU ignored on NEWLINK")
variable t_hlen is assigned values that are never read,
hence they are redundant and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Wed, 1 Aug 2018 01:59:56 +0000 (01:59 +0000)]
tcp: remove set but not used variable 'skb_size'
Fixes gcc '-Wunused-but-set-variable' warning:
net/ipv4/tcp_output.c: In function 'tcp_collapse_retrans':
net/ipv4/tcp_output.c:2700:6: warning:
variable 'skb_size' set but not used [-Wunused-but-set-variable]
int skb_size, next_skb_size;
^
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Aug 2018 16:56:11 +0000 (09:56 -0700)]
Merge branch 'tcp-add-4-new-stats'
Wei Wang says:
====================
tcp: add 4 new stats
This patch series adds 3 RFC4898 stats:
1. tcpEStatsPerfHCDataOctetsOut
2. tcpEStatsPerfOctetsRetrans
3. tcpEStatsStackDSACKDups
and an addtional stat to record the number of data packet reordering
events seen:
4. tcp_reord_seen
Together with the existing stats, application can use them to measure
the retransmission rate in bytes, exclude spurious retransmissions
reflected by DSACK, and keep track of the reordering events on live
connections.
In particular the networks with different MTUs make bytes-based loss stats
more useful. Google servers have been using these stats for many years to
instrument transport and network performance.
Note: The first patch is a refactor to add a helper to calculate
opt_stats size in order to make later changes cleaner.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Wed, 1 Aug 2018 00:46:24 +0000 (17:46 -0700)]
tcp: add stat of data packet reordering events
Introduce a new TCP stats to record the number of reordering events seen
and expose it in both tcp_info (TCP_INFO) and opt_stats
(SOF_TIMESTAMPING_OPT_STATS).
Application can use this stats to track the frequency of the reordering
events in addition to the existing reordering stats which tracks the
magnitude of the latest reordering event.
Note: this new stats tracks reordering events triggered by ACKs, which
could often be fewer than the actual number of packets being delivered
out-of-order.
Signed-off-by: Wei Wang <weiwan@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Wed, 1 Aug 2018 00:46:23 +0000 (17:46 -0700)]
tcp: add dsack blocks received stats
Introduce a new TCP stat to record the number of DSACK blocks received
(RFC4989 tcpEStatsStackDSACKDups) and expose it in both tcp_info
(TCP_INFO) and opt_stats (SOF_TIMESTAMPING_OPT_STATS).
Signed-off-by: Wei Wang <weiwan@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Wed, 1 Aug 2018 00:46:22 +0000 (17:46 -0700)]
tcp: add data bytes retransmitted stats
Introduce a new TCP stat to record the number of bytes retransmitted
(RFC4898 tcpEStatsPerfOctetsRetrans) and expose it in both tcp_info
(TCP_INFO) and opt_stats (SOF_TIMESTAMPING_OPT_STATS).
Signed-off-by: Wei Wang <weiwan@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Wed, 1 Aug 2018 00:46:21 +0000 (17:46 -0700)]
tcp: add data bytes sent stats
Introduce a new TCP stat to record the number of bytes sent
(RFC4898 tcpEStatsPerfHCDataOctetsOut) and expose it in both tcp_info
(TCP_INFO) and opt_stats (SOF_TIMESTAMPING_OPT_STATS).
Signed-off-by: Wei Wang <weiwan@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Wed, 1 Aug 2018 00:46:20 +0000 (17:46 -0700)]
tcp: add a helper to calculate size of opt_stats
This is to refactor the calculation of the size of opt_stats to a helper
function to make the code cleaner and easier for later changes.
Suggested-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Wei Wang <weiwan@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
ipv4: Control SKB reprioritization after forwarding
After IPv4 packets are forwarded, the priority of the corresponding SKB
is updated according to the TOS field of IPv4 header. This overrides any
prioritization done earlier by e.g. an skbedit action or ingress-qos-map
defined at a vlan device.
Such overriding may not always be desirable. Even if the packet ends up
being routed, which implies this is an L3 network node, an administrator
may wish to preserve whatever prioritization was done earlier on in the
pipeline.
Therefore this patch set introduces a sysctl that controls this
behavior, net.ipv4.ip_forward_update_priority. It's value is 1 by
default to preserve the current behavior.
All of the above is implemented in patch #1.
Value changes prompt a new NETEVENT_IPV4_FWD_UPDATE_PRIORITY_UPDATE
notification, so that the drivers can hook up whatever logic may depend
on this value. That is implemented in patch #2.
In patches #3 and #4, mlxsw is adapted to recognize the sysctl. On
initialization, the RGCR register that handles router configuration is
set in accordance with the sysctl. The new notification is listened to
and RGCR is reconfigured as necessary.
In patches #5 to #7, a selftest is added to verify that mlxsw reflects
the sysctl value as necessary. The test is expressed in terms of the
recently-introduced ieee_setapp support, and works by observing how DSCP
value gets rewritten depending on packet priority. For this reason, the
test is added to the subdirectory drivers/net/mlxsw. Even though it's
not particularly specific to mlxsw, it's not suitable for running on
soft devices (which don't support the ieee_setapp et.al.).
Changes from v1 to v2:
- In patch #1, init sysctl_ip_fwd_update_priority to 1 instead of true.
Changes from RFC to v1:
- Fix wrong sysctl name in ip-sysctl.txt
- Add notifications
- Add mlxsw support
- Add self test
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Tue, 31 Jul 2018 22:39:29 +0000 (00:39 +0200)]
selftests: mlxsw: Add test for ip_forward_update_priority
Verify that with that sysctl turned off, DSCP prioritization and rewrite
works the same way as in qos_dscp_bridge test. However when the sysctl
is charged, there should be a reprioritization after routing stage,
which will be observed by a different DSCP rewrite on egress.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Tue, 31 Jul 2018 22:39:25 +0000 (00:39 +0200)]
selftests: forwarding: Move DSCP capture to lib.sh
dscp_capture_install() and dscp_capture_uninstall() are going to be
useful for a test added by a following patch, move them therefore to
lib.sh together with related helpers.
While doing so, change the rule preference from mere DSCP value to
DSCP+100 in order to support adding captures of packets with DSCP of 0.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Tue, 31 Jul 2018 22:38:59 +0000 (00:38 +0200)]
selftests: forwarding: Move lldpad waiting to lib.sh
The function lldpad_wait() will be useful for a test added by a
following patch. Likewise would the "sleep 5" with its extensive
comment.
Therefore move lldpad_wait() to lib.sh in order to allow reuse. Rename
it to lldpad_app_wait_set() to recognize that what this is intended to
wait on are the pending APP sets.
For the sleeping, add a function lldpad_app_wait_del(). That will serve
to hold the related explanatory comment (which edit for clarity), and as
a token in the caller to identify the sites where this sort of waiting
takes place. That will serve when/if a better way to handle this
business is found.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This sysctl setting controls whether packet priority should be updated
after forwarding. Configure RGCR.usp accordingly so that the device is
in sync with the kernel handling.
Note that RGCR doesn't allow changing arbitrary parameters
mid-operation, however "usp" is exempt and can be reconfigured.
Also react to NETEVENT_IPV4_FWD_UPDATE_PRIORITY_UPDATE notifications
that signify change in this configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Tue, 31 Jul 2018 22:37:36 +0000 (00:37 +0200)]
mlxsw: spectrum: Extract work-scheduling into a new function
The boilerplate to schedule NETEVENT_IPV4_MPATH_HASH_UPDATE and
NETEVENT_IPV6_MPATH_HASH_UPDATE handling is almost equivalent to that of
NETEVENT_IPV4_FWD_UPDATE_PRIORITY_UPDATE that's coming in the next
patch. The only difference is which actual worker function should be
called. Extract this boilerplate into a named function in order to allow
reuse.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Tue, 31 Jul 2018 22:36:42 +0000 (00:36 +0200)]
net: ipv4: Notify about changes to ip_forward_update_priority
Drivers may make offloading decision based on whether
ip_forward_update_priority is enabled or not. Therefore distribute
netevent notifications to give them a chance to react to a change.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Tue, 31 Jul 2018 22:36:03 +0000 (00:36 +0200)]
net: ipv4: Control SKB reprioritization after forwarding
After IPv4 packets are forwarded, the priority of the corresponding SKB
is updated according to the TOS field of IPv4 header. This overrides any
prioritization done earlier by e.g. an skbedit action or ingress-qos-map
defined at a vlan device.
Such overriding may not always be desirable. Even if the packet ends up
being routed, which implies this is an L3 network node, an administrator
may wish to preserve whatever prioritization was done earlier on in the
pipeline.
Therefore introduce a sysctl that controls this behavior. Keep the
default value at 1 to maintain backward-compatible behavior.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vincent Bernat [Tue, 31 Jul 2018 19:18:11 +0000 (21:18 +0200)]
net: add helpers checking if socket can be bound to nonlocal address
The construction "net->ipv4.sysctl_ip_nonlocal_bind || inet->freebind
|| inet->transparent" is present three times and its IPv6 counterpart
is also present three times. We introduce two small helpers to
characterize these tests uniformly.
Signed-off-by: Vincent Bernat <vincent@bernat.im> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Mason [Tue, 31 Jul 2018 15:56:19 +0000 (11:56 -0400)]
net: change Exar/Neterion menu items to be alphabetical
Neterion was standalone for several years, then acquired by Exar and
shutdown in 11 months without ever making any new Exar branded adapters.
Users would probably think of them as Neterion and not Exar (as there
have been no follow-on adapters and the vast majority ever sold were
under the Neterion name).
6c541b4595a2 ("net: ethernet: Sort Kconfig sourcing alphabetically")
sorted Kconfig sourcing based on directory names, but in a couple cases,
the menu item text is quite different from the directory name and is not
sorted correctly:
To address that and clear up any confusion about the name, "Exar" was
changed to "Neterion (Exar)" and the relevant entries in the Makefile
and Kconfig were reordered to match the alphabetical organization.
Inspired-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Jon Mason <jdmason@kudzu.us> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 31 Jul 2018 16:01:37 +0000 (17:01 +0100)]
net/tipc: remove redundant variables 'tn' and 'oport'
Variables 'tn' and 'oport' are being assigned but are never used hence
they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'oport' set but not used [-Wunused-but-set-variable]
warning: variable 'tn' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
be2net: gather debug info and reset adapter (only for Lancer) on a tx-timeout
This patch handles a TX-timeout as follows:
1) This patch gathers and prints the following info that can
help in diagnosing the cause of a TX-timeout.
a) TX queue and completion queue entries.
b) SKB and TCP/UDP header details.
2) For Lancer NICs (TX-timeout recovery is not supported for
BE3/Skyhawk-R NICs), it recovers from the TX timeout as follows:
a) On a TX-timeout, driver sets the PHYSDEV_CONTROL_FW_RESET_MASK
bit in the PHYSDEV_CONTROL register. Lancer firmware goes into
an error state and indicates this back to the driver via a bit
in a doorbell register.
b) Driver detects this and calls be_err_recover(). DMA is disabled,
all pending TX skbs are unmapped and freed (be_close()). All rings
are destroyed (be_clear()).
c) The driver waits for the FW to re-initialize and re-creates all
rings along with other data structs (be_resume())
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There is a potential execution path in which variable *err* is returned
without being properly initialized previously.
Fix this by initializing variable *err* to 0.
Addresses-Coverity-ID: 1472116 ("Uninitialized scalar variable") Fixes: 0ec13877ce95 ("net/mlx5e: Gather all XDP pre-requisite checks in a single function") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Acked-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/qlogic/qed/qed_cxt.c:1534:6: warning: symbol 'qed_cm_init_pf' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:233:4: warning: symbol 'qed_init_qm_get_num_tcs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:238:5: warning: symbol 'qed_init_qm_get_num_vfs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:246:5: warning: symbol 'qed_init_qm_get_num_pf_rls' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:264:5: warning: symbol 'qed_init_qm_get_num_vports' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:276:5: warning: symbol 'qed_init_qm_get_num_pqs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:573:5: warning: symbol 'qed_mcp_nvm_wr_cmd' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:3012:1: warning: symbol '__qed_mcp_resc_lock' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dcbx.c:870:6: warning: symbol 'qed_dcbx_aen' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7841:5: warning: symbol 'qed_dbg_nvm_image_length' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7857:5: warning: symbol 'qed_dbg_nvm_image' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:675:6: warning: symbol '_qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:690:6: warning: symbol 'qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:3982:6: warning: symbol 'qed_iov_pf_get_pending_events' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_vf.c:172:5: warning: symbol '_qed_vf_pf_release' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:137:5: warning: symbol 'qed_rdma_get_sb_id' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:709:5: warning: symbol 'qed_rdma_stop' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_ll2.c:161:6: warning: symbol 'qed_ll2b_complete_rx_packet' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_roce.c:160:6: warning: symbol 'qed_roce_free_cid_pair' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:380:12: warning: symbol 'iwarp_state_names' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:946:1: warning: symbol 'qed_iwarp_parse_private_data' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:971:1: warning: symbol 'qed_iwarp_mpa_reply_arrived' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2504:1: warning: symbol 'qed_iwarp_ll2_slowpath' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2806:6: warning: symbol 'qed_iwarp_qp_in_error' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2827:6: warning: symbol 'qed_iwarp_exception_received' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2958:1: warning: symbol 'qed_iwarp_connect_complete' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iscsi.c:876:6: warning: symbol 'qed_iscsi_free_connection' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Denis Bolotin <Denis.Bolotin@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
rds: rds_ib_recv_alloc_cache() should call alloc_percpu_gfp() instead
Currently, rds_ib_conn_alloc() calls rds_ib_recv_alloc_caches()
without passing along the gfp_t flag. But rds_ib_recv_alloc_caches()
and rds_ib_recv_alloc_cache() should take a gfp_t parameter so that
rds_ib_recv_alloc_cache() can call alloc_percpu_gfp() using the
correct flag instead of calling alloc_percpu().
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Mon, 30 Jul 2018 22:05:39 +0000 (01:05 +0300)]
net: ethernet: ti: cpsw: replace unnecessarily macroses on functions
Replace ugly macroses on functions.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Mon, 23 Jul 2018 16:18:38 +0000 (17:18 +0100)]
rxrpc: Transmit more ACKs during data reception
Immediately flush any outstanding ACK on entry to rxrpc_recvmsg_data() -
which transfers data to the target buffers - if we previously had an Rx
underrun (ie. we returned -EAGAIN because we ran out of received data).
This lets the server know what we've managed to receive something.
Also flush any outstanding ACK after calling the function if it hit -EAGAIN
to let the server know we processed some data.
It might be better to send more ACKs, possibly on a time-based scheme, but
that needs some more consideration.
With this and some additional AFS patches, it is possible to get large
unencrypted O_DIRECT reads to be almost as fast as NFS over TCP. It looks
like it might be theoretically possible to improve performance yet more for
a server running a single operation as investigation of packet timestamps
indicates that the server keeps stalling.
The issue appears to be that rxrpc runs in to trouble with ACK packets
getting batched together (up to ~32 at a time) somewhere between the IP
transmit queue on the client and the ethernet receive queue on the server.
However, this case isn't too much of a worry as even a lightly loaded
server should be receiving sufficient packet flux to flush the ACK packets
to the UDP socket.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 23 Jul 2018 16:18:37 +0000 (17:18 +0100)]
rxrpc: Propose, but don't immediately transmit, the final ACK for a call
The final ACK that closes out an rxrpc call needs to be transmitted by the
client unless we're going to follow up with a DATA packet for a new call on
the same channel (which implicitly ACK's the previous call, thereby saving
an ACK).
Currently, we don't do that, so if no follow on call is immediately
forthcoming, the server will resend the last DATA packet - at which point
rxrpc_conn_retransmit_call() will be triggered and will (re)send the final
ACK. But the server has to hold on to the last packet until the ACK is
received, thereby holding up its resources.
Fix the client side to propose a delayed final ACK, to be transmitted after
a short delay, assuming the call isn't superseded by a new one.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 23 Jul 2018 16:18:37 +0000 (17:18 +0100)]
rxrpc: Increase the size of a call's Rx window
Increase the size of a call's Rx window from 32 to 63 - ie. one less than
the size of the ring buffer. This makes large data transfers perform
better when the Tx window on the other side is around 64 (as is the case
with Auristor's YFS fileserver).
If the server window size is ~32 or smaller, this should make no
difference.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 23 Jul 2018 16:18:37 +0000 (17:18 +0100)]
rxrpc: Fix ACK proposal tracepoint
Fix the ACK proposal tracepoint outcomes list by making the one that's an
empty string not an empty string - which gets rendered as a hex number
string instead.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 23 Jul 2018 16:18:37 +0000 (17:18 +0100)]
rxrpc: Trace packet transmission
Trace successful packet transmission (kernel_sendmsg() succeeded, that is)
in AF_RXRPC. We can share the enum that defines the transmission points
with the trace_rxrpc_tx_fail() tracepoint, so rename its constants to be
applicable to both.
Also, save the internal call->debug_id in the rxrpc_channel struct so that
it can be used in retransmission trace lines.
Signed-off-by: David Howells <dhowells@redhat.com>
YueHaibing [Wed, 1 Aug 2018 09:52:34 +0000 (17:52 +0800)]
rxrpc: remove redundant variables 'sp' and 'did_discard'
Variables 'sp' and 'did_discard' are being assigned,
but are never used, hence they are redundant and can be removed.
fix following warning:
net/rxrpc/call_event.c:165:25: warning: variable 'sp' set but not used [-Wunused-but-set-variable]
net/rxrpc/conn_client.c:1054:7: warning: variable 'did_discard' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David Howells <dhowells@redhat.com>
We never use RCU protection for it, just a lot of cargo-cult
rcu_deference_protects calls.
Note that we do keep the kfree_rcu call for it, as the references through
struct sock are RCU protected and thus might require a grace period before
freeing.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Eric Dumazet <edumazet@google.com> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Tue, 31 Jul 2018 09:43:39 +0000 (17:43 +0800)]
virtio-net: get rid of unnecessary container of rq stats
We don't maintain tx counters in rx stats any more. There's no need
for an extra container of rq stats.
Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Tue, 31 Jul 2018 09:43:38 +0000 (17:43 +0800)]
virtio-net: correctly update XDP_TX counters
Commit 5b8f3c8d30a6 ("virtio_net: Add XDP related stats") tries to
count TX XDP stats in virtnet_receive(). This will cause several
issues:
- virtnet_xdp_sq() was called without checking whether or not XDP is
set. This may cause out of bound access when there's no enough txq
for XDP.
- Stats were updated even if there's no XDP/XDP_TX.
Fixing this by reusing virtnet_xdp_xmit() for XDP_TX which can counts
TX XDP counter itself and remove the unnecessary tx stats embedded in
rx stats.
Reported-by: syzbot+604f8271211546f5b3c7@syzkaller.appspotmail.com Fixes: 5b8f3c8d30a6 ("virtio_net: Add XDP related stats") Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
xsk: improvements to RX queue check and replace
First 3 patches of my recent RFC. The first one make the check against
real_num_rx_queues slightly more reliable, while the latter two redefine
XDP_QUERY_XSK_UMEM slightly to disallow replacing UMEM in the driver at
the stack level.
I'm not sure where this lays on the bpf vs net trees scale, but there
should be no conflicts with either tree.
====================
Acked-by: Björn Töpel <bjorn.topel@intel.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 31 Jul 2018 03:43:53 +0000 (20:43 -0700)]
xsk: don't allow umem replace at stack level
Currently drivers have to check if they already have a umem
installed for a given queue and return an error if so. Make
better use of XDP_QUERY_XSK_UMEM and move this functionality
to the core.
We need to keep rtnl across the calls now.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Acked-by: Björn Töpel <bjorn.topel@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 31 Jul 2018 03:43:52 +0000 (20:43 -0700)]
xsk: refactor xdp_umem_assign_dev()
Return early and only take the ref on dev once there is no possibility
of failing.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Acked-by: Björn Töpel <bjorn.topel@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 31 Jul 2018 03:43:51 +0000 (20:43 -0700)]
net: update real_num_rx_queues even when !CONFIG_SYSFS
We used to depend on real_num_rx_queues as a upper bound for sanity
checks. For AF_XDP socket validation it's useful if the check behaves
the same regardless of CONFIG_SYSFS setting.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5: handle DMA mapping error case for XDP redirect
Commit 58b99ee3e3eb ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
forgot to return/free the xdp_frame in case the DMA mapping failed, correct this.
Also DMA unmap the frame in case mlx5e_xmit_xdp_frame() fails.
Fixes: 58b99ee3e3eb ("net/mlx5e: Add support for XDP_REDIRECT in device-out side") Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements following ethtool stats fields for netvsc:
cpu<n>_tx/rx_packets/bytes
cpu<n>_vf_tx/rx_packets/bytes
Corresponding per-cpu counters already exist in current code. Exposing
these counters will help troubleshooting performance issues.
for_each_present_cpu() was used instead of for_each_possible_cpu().
for_each_possible_cpu() would create very long and useless output.
It is still being used for internal buffer, but not for ethtool
output.
There could be an overflow if cpu was added between ethtool
call netvsc_get_sset_count() and netvsc_get_ethtool_stats() and
netvsc_get_strings(). (still safe if cpu was removed)
ethtool makes these three function calls separately.
As long as we use ethtool, I can't see any clean solution.
Currently and in foreseeable short term, Hyper-V doesn't support
cpu hot-plug. Plus, ethtool is for admin use. Unlikely the admin
would perform such combo operations.
Changes in v2:
- Remove cpp style comment
- Resubmit after freeze
Changes in v3:
- Reimplemented with kvmalloc instead of alloc_percpu
Changes in v4:
- Fixed inconsistent array size
- Use kvmalloc_array instead of kvmalloc
Signed-off-by: Yidong Ren <yidren@microsoft.com> Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
A test for mirror-to-gretap with team in UL packet path
This patchset adds a test for "tc action mirred mirror" where the
mirrored-to device is a gretap, and underlay path contains a team
device.
In patch #1 require_command() is added, which should henceforth be used
to declare dependence on a certain tool.
In patch #2, two new functions, team_create() and team_destroy(), are
added to lib.sh.
The newly-added test uses arping, which isn't necessarily available.
Therefore patch #3 introduces $ARPING, and a preexisting test is fixed
to require_command $ARPING.
In patches #4 and #5, two new tests are added. In both cases, a team
device is on egress path of a mirrored packet in a mirror-to-gretap
scenario. In the first one, the team device is in loadbalance mode, in
the second one it's in lacp mode. (The difference in modes necessitates
a different testing strategy, hence two test cases instead of just
parameterizing one.)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Mon, 30 Jul 2018 14:40:07 +0000 (16:40 +0200)]
selftests: forwarding: Test mirror-to-gretap w/ UL team LACP
This tests mirror-to-gretap when an underlay packet path includes a team
device which is not in loadbalance mode, but in LACP mode. The test
manipulates LAG membership to achieve changes in txability, thus making
sure that a driver that offloads mirror-to-gretap doesn't just consider
upness of a device.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Mon, 30 Jul 2018 14:40:02 +0000 (16:40 +0200)]
selftests: forwarding: Test mirror-to-gretap w/ UL team
Test for "tc action mirred egress mirror" that mirrors to gretap when
the underlay route points at a VLAN-aware bridge (802.1q), and the
traffic egresses the bridge through a team device. Test upping and
downing individual team device slaves and verify the traffic flows as
expected.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Mon, 30 Jul 2018 14:39:46 +0000 (16:39 +0200)]
selftests: forwarding: lib: Add require_command()
The logic for testing whether a certain command is available is used
several times in the current code base. The tests in follow-up patches
add more requirements like that.
Therefore extract the logic into a named function, require_command(),
that can be used directly from lib.sh as well as from any test that
wishes to declare dependence on some command.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: mscc: the extended page access register is 16 bits
The Extended Page Access is a 16-bit register, so change the page
parameter of vsc85xx_phy_page_set to a u16.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/tls: Use socket data_ready callback on record availability
On receipt of a complete tls record, use socket's saved data_ready
callback instead of state_change callback. In function tls_queue(),
the TLS record is queued in encrypted state. But the decryption
happen inline when tls_sw_recvmsg() or tls_sw_splice_read() get invoked.
So it should be ok to notify the waiting context about the availability
of data as soon as we could collect a full TLS record. For new data
availability notification, sk_data_ready callback is more appropriate.
It points to sock_def_readable() which wakes up specifically for EPOLLIN
event. This is in contrast to the socket callback sk_state_change which
points to sock_def_wakeup() which issues a wakeup unconditionally
(without event mask).
Signed-off-by: Vakul Garg <vakul.garg@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This series is aimed at improving the act_mirred redirect performances.
Such action is used by OVS to represent TC S/W flows, and it's current largest
bottle-neck is the need for a skb_clone() for each packet.
The first 2 patches introduce some cleanup and safeguards to allow extending
tca_result - we will use it to store RCU protected redirect information - and
introduce a clear separation between user-space accessible tcfa_action
values and internal values accessible only by the kernel.
Then a new tcfa_action value is introduced: TC_ACT_REINJECT, similar to
TC_ACT_REDIRECT, but preserving the mirred semantic. Such value is not
accessible from user-space.
The last patch exploits the newly introduced infrastructure in the act_mirred
action, to avoid a skb_clone, when possible.
Overall this the above gives a ~10% performance improvement in forwarding tput,
when using the TC S/W datapath.
v1 -> v2:
- preserve the rcu lock in act_bpf
- add and use a new action value to reinject the packets, preserving the mirred
semantic
v2 -> v3:
- renamed to new action as TC_ACT_REINJECT
- TC_ACT_REINJECT is not exposed to user-space
v3 -> v4:
- dropped the TC_ACT_REDIRECT patch
- report failure via extack, too
- rename the new action as TC_ACT_REINSERT
- skip clone only if the control action don't touch tcf_result
v4 -> v5:
- fix a couple of build issue reported by kbuild bot
- dont split messages
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Mon, 30 Jul 2018 12:30:45 +0000 (14:30 +0200)]
act_mirred: use TC_ACT_REINSERT when possible
When mirred is invoked from the ingress path, and it wants to redirect
the processed packet, it can now use the TC_ACT_REINSERT action,
filling the tcf_result accordingly, and avoiding a per packet
skb_clone().
Overall this gives a ~10% improvement in forwarding performance for the
TC S/W data path and TC S/W performances are now comparable to the
kernel openvswitch datapath.
v1 -> v2: use ACT_MIRRED instead of ACT_REDIRECT
v2 -> v3: updated after action rename, fixed typo into the commit
message
v3 -> v4: updated again after action rename, added more comments to
the code (JiriP), skip the optimization if the control action
need to touch the tcf_result (Paolo)
v4 -> v5: fix sparse warning (kbuild bot)
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Mon, 30 Jul 2018 12:30:44 +0000 (14:30 +0200)]
net/tc: introduce TC_ACT_REINSERT.
This is similar TC_ACT_REDIRECT, but with a slightly different
semantic:
- on ingress the mirred skbs are passed to the target device
network stack without any additional check not scrubbing.
- the rcu-protected stats provided via the tcf_result struct
are updated on error conditions.
This new tcfa_action value is not exposed to the user-space
and can be used only internally by clsact.
v1 -> v2: do not touch TC_ACT_REDIRECT code path, introduce
a new action type instead
v2 -> v3:
- rename the new action value TC_ACT_REINJECT, update the
helper accordingly
- take care of uncloned reinjected packets in XDP generic
hook
v3 -> v4:
- renamed again the new action value (JiriP)
v4 -> v5:
- fix build error with !NET_CLS_ACT (kbuild bot)
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Mon, 30 Jul 2018 12:30:43 +0000 (14:30 +0200)]
tc/act: remove unneeded RCU lock in action callback
Each lockless action currently does its own RCU locking in ->act().
This allows using plain RCU accessor, even if the context
is really RCU BH.
This change drops the per action RCU lock, replace the accessors
with the _bh variant, cleans up a bit the surrounding code and
documents the RCU status in the relevant header.
No functional nor performance change is intended.
The goal of this patch is clarifying that the RCU critical section
used by the tc actions extends up to the classifier's caller.
v1 -> v2:
- preserve rcu lock in act_bpf: it's needed by eBPF helpers,
as pointed out by Daniel
v3 -> v4:
- fixed some typos in the commit message (JiriP)
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Mon, 30 Jul 2018 12:30:42 +0000 (14:30 +0200)]
net/sched: user-space can't set unknown tcfa_action values
Currently, when initializing an action, the user-space can specify
and use arbitrary values for the tcfa_action field. If the value
is unknown by the kernel, is implicitly threaded as TC_ACT_UNSPEC.
This change explicitly checks for unknown values at action creation
time, and explicitly convert them to TC_ACT_UNSPEC. No functional
changes are introduced, but this will allow introducing tcfa_action
values not exposed to user-space in a later patch.
Note: we can't use the above to hide TC_ACT_REDIRECT from user-space,
as the latter is already part of uAPI.
v3 -> v4:
- use an helper to check for action validity (JiriP)
- emit an extack for invalid actions (JiriP)
v4 -> v5:
- keep messages on a single line, drop net_warn (Marcelo)
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in hiding this logic in a helper. Also remove the
useless events != 0 check and only busy loop once we know we actually
have a poll method.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: David S. Miller <davem@davemloft.net>
net: don not detour through struct sock to find the poll waitqueue
For any open socket file descriptor sock->sk->sk_wq->wait will always
point to sock->wq->wait. That means we can do the shorter dereference
and removal a NULL check and don't have to not worry about any RCU
protection.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: David S. Miller <davem@davemloft.net>
act_bpf: Use kmemdup instead of duplicating it in tcf_bpf_init_from_ops
Replace calls to kmalloc followed by a memcpy with a direct call to
kmemdup.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
cls_bpf: Use kmemdup instead of duplicating it in cls_bpf_prog_from_ops
Replace calls to kmalloc followed by a memcpy with a direct call to
kmemdup.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Wang [Sat, 28 Jul 2018 05:35:56 +0000 (13:35 +0800)]
net-next: mediatek: cleanup unnecessary get chip id and its user
Since driver is devicetree-based, all device type and charateristic can be
determined by the compatible string and its data. It's unnecessary to
create another dependent function to check chip ID and then decide whether
the specific funciton is being supported on a certain device. It can be
totally replaced by the existing flag, so a cleanup is made by removing
the function and the only user, HWLRO.
MT2701 also have a missing HWLRO support in old code, so add it the same
patch.
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sysfs: Fix regression when adding a file to an existing group
Commit 5f81880d5204 ("sysfs, kobject: allow creating kobject belonging
to arbitrary users") incorrectly changed the argument passed as the
parent parameter when calling sysfs_add_file_mode_ns(). This caused some
sysfs attribute files to not be added correctly to certain groups.
Fixes: 5f81880d5204 ("sysfs, kobject: allow creating kobject belonging to arbitrary users") Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Reported-by: Heiner Kallweit <hkallweit1@gmail.com> Tested-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This series from Gal and Saeed provides updates to mlx5 vxlan implementation.
Gal, started with three cleanups to reflect the actual hardware vxlan state
- reflect 4789 UDP port default addition to software database
- check maximum number of vxlan UDP ports
- cleanup an unused member in vxlan work
Then Gal provides performance optimization by replacing the
vxlan radix tree with a hash table.
Measuring mlx5e_vxlan_lookup_port execution time:
Radix Tree Hash Table
--------------- ------------ ------------
Single Stream 161 ns 79 ns (51% improvement)
Multi Stream 259 ns 136 ns (47% improvement)
Next, from Saeed, vxlan refactoring to allow sharing the vxlan table
between different mlx5 netdevice instances like PF and VF representors,
this is done by making mlx5 vxlan interface more generic and decoupling
it from PF netdevice structures and logic, then moving it into mlx5 core
as a low level interface so it can be used by VF representors, which is
illustrated in the last patch of the serious.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If an invalid MTU value is set through rtnetlink return extra error
information instead of putting message in kernel log. For other cases
where there is no visible API, keep the error report in the log.
Example:
# ip li set dev enp12s0 mtu 10000
Error: mtu greater than device maximum.
# ifconfig enp12s0 mtu 10000
SIOCSIFMTU: Invalid argument
# dmesg | tail -1
[ 2047.795467] enp12s0: mtu greater than device maximum
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 27 Jul 2018 20:11:00 +0000 (13:11 -0700)]
net: dcb: add DSCP to comment about priority selector types
Commit ee2059819450 ("net/dcb: Add dscp to priority selector type")
added a define for the new DSCP selector type created by
IEEE 802.1Qcd, but missed the comment enumerating all selector types.
Update the comment.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Fri, 27 Jul 2018 16:54:39 +0000 (19:54 +0300)]
net: ethernet: ti: cpsw: add missed RX_CTAG feature for second slave
Seems it was missed while adding for first net dev in dual-emac mode.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
route: add support and selftests for directed broadcast forwarding
Patch 1/2 is the feature and 2/2 is the selftest. Check the changelog
on each of them to know the details.
v1->v2:
- fix a typo in changelog.
- fix an uapi break that Davide noticed.
- flush route cache when bc_forwarding is changed.
- add the selftest for this patch as Ido's suggestion.
v2->v3:
- fix an incorrect 'if check' in devinet_conf_proc as David Ahern
noticed.
- extend the selftest after one David Ahern fix for vrf.
v3->v4:
- improve the output log in the selftest as David Ahern suggested.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Fri, 27 Jul 2018 08:37:29 +0000 (16:37 +0800)]
selftests: add a selftest for directed broadcast forwarding
As Ido's suggestion, this patch is to add a selftest for directed
broadcast forwarding with vrf. It does the assertion by checking
the src IP of the echo-reply packet in ping_test_from.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Fri, 27 Jul 2018 08:37:28 +0000 (16:37 +0800)]
route: add support for directed broadcast forwarding
This patch implements the feature described in rfc1812#section-5.3.5.2
and rfc2644. It allows the router to forward directed broadcast when
sysctl bc_forwarding is enabled.
Note that this feature could be done by iptables -j TEE, but it would
cause some problems:
- target TEE's gateway param has to be set with a specific address,
and it's not flexible especially when the route wants forward all
directed broadcasts.
- this duplicates the directed broadcasts so this may cause side
effects to applications.
Besides, to keep consistent with other os router like BSD, it's also
necessary to implement it in the route rx path.
Note that route cache needs to be flushed when bc_forwarding is
changed.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vincent Bernat [Wed, 25 Jul 2018 11:19:13 +0000 (13:19 +0200)]
net/ipv6: allow any source address for sendmsg pktinfo with ip_nonlocal_bind
When freebind feature is set of an IPv6 socket, any source address can
be used when sending UDP datagrams using IPv6 PKTINFO ancillary
message. Global non-local bind feature was added in commit 35a256fee52c ("ipv6: Nonlocal bind") for IPv6. This commit also allows
IPv6 source address spoofing when non-local bind feature is enabled.
Signed-off-by: Vincent Bernat <vincent@bernat.im> Signed-off-by: David S. Miller <davem@davemloft.net>
this is a pull request for net-next/master consisting of 38 patches.
Dan Murphy's patch fixes the path to a file in the comment of the CAN
Error Message Frame Mask structure.
A patch by Colin Ian King fixes a typo in the cc770 driver.
The next patch is by me an sorts the Kconfigand Makefile entries of the
CAN-USB driver subdir alphabetically.
The patch by Jakob Unterwurzacher adds support for the UCAN USB-CAN
adapter.
YueHaibing's patch replaces a open coded skb_put()+memset() by
skb_put_zero() in the CAN-dev infrastructure.
Zhu Yi provides a patch to enable multi-queue CAN devices.
Three patches by Luc Van Oostenryck fix the return value of several
driver's xmit function, I contribute a patch for the a fourth driver.
Fabio Estevam's patch switches the flexcan driver to SPDX identifier.
Two patches by Jia-Ju Bai replace the mdelay() by a usleep_range() in
the sja1000 drivers.
The next 6 patches are by Anssi Hannula and refactor the xilinx CAN
driver and add support for the xilinx CAN FD core.
A patch by Gustavo A. R. Silva adds fallthrough annotation to the
peak_usb driver.
5 patches by Stephane Grosjean for the peak CANFD driver do some
cleanups and provide more improvements for further firmware releases.
The remaining 13 patches are by Jimmy Assarsson and the first clean up
the kvaser_usb driver, so that the later patches add support for the
Kvaser USB hydra family.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-kernels.git / log