David Brownell [Thu, 9 Sep 2010 23:38:03 +0000 (16:38 -0700)]
gpio: doc updates
There's been some recent confusion about error checking GPIO numbers.
briefly, it should be handled mostly during setup, when gpio_request() is
called, and NEVER by expectig gpio_is_valid to report more than
never-usable GPIO numbers.
[akpm@linux-foundation.org: terminate unterminated comment] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Eric Miao" <eric.y.miao@gmail.com> Cc: "Ryan Mallon" <ryan@bluewatersys.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gpio: sx150x: correct and refine reset-on-probe behavior
Replace the arbitrary software-reset call from the device-probe
method, because:
- It is defective. To work correctly, it should be two byte writes,
not a single word write. As it stands, it does nothing.
- Some devices with sx150x expanders installed have their NRESET pins
ganged on the same line, so resetting one causes the others to reset -
not a nice thing to do arbitrarily!
- The probe, usually taking place at boot, implies a recent hard-reset,
so a software reset at this point is just a waste of energy anyway.
Therefore, make it optional, defaulting to off, as this will match the
common case of probing at powerup and also matches the current broken
no-op behavior.
Signed-off-by: Gregory Bean <gbean@codeaurora.org> Reviewed-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
memory hotplug: fix next block calculation in is_removable
next_active_pageblock() is for finding next _used_ freeblock. It skips
several blocks when it finds there are a chunk of free pages lager than
pageblock. But it has 2 bugs.
1. We have no lock. page_order(page) - pageblock_order can be minus.
2. pageblocks_stride += is wrong. it should skip page_order(p) of pages.
Minchan Kim [Thu, 9 Sep 2010 23:38:00 +0000 (16:38 -0700)]
mm: compaction: handle active and inactive fairly in too_many_isolated
Iram reported that compaction's too_many_isolated() loops forever.
(http://www.spinics.net/lists/linux-mm/msg08123.html)
The meminfo when the situation happened was inactive anon is zero. That's
because the system has no memory pressure until then. While all anon
pages were in the active lru, compaction could select active lru as well
as inactive lru. That's a different thing from vmscan's isolated. So we
has been two too_many_isolated.
While compaction can isolate pages in both active and inactive, current
implementation of too_many_isolated only considers inactive. It made
Iram's problem.
This patch handles active and inactive fairly. That's because we can't
expect where from and how many compaction would isolated pages.
This patch changes (nr_isolated > nr_inactive) with
nr_isolated > (nr_active + nr_inactive) / 2.
Ira W. Snyder [Thu, 9 Sep 2010 23:37:58 +0000 (16:37 -0700)]
arch/powerpc/include/asm/fsldma.h needs slab.h
The slab.h header is required to use the kmalloc() family of functions.
Due to recent kernel changes, this header must be directly included by
code that calls into the memory allocator.
Without this patch, any code which includes this header fails to build.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc: m41t80: do not use rtc_valid_tm in m41t80_rtc_read_alarm
Commit b485fe5ea ("rtc/m41t80: use rtc_valid_tm() to check returned tm")
added rtc_valid_tm to m41t80_rtc_read_alarm() but it was wrong while the
t->time does not contain complete date/time.
This patch also fixes a warning:
warning: passing argument 1 of 'rtc_valid_tm' from incompatible pointer type
Jan Sembera [Thu, 9 Sep 2010 23:37:54 +0000 (16:37 -0700)]
binfmt_misc: fix binfmt_misc priority
Commit 74641f584da ("alpha: binfmt_aout fix") (May 2009) introduced a
regression - binfmt_misc is now consulted after binfmt_elf, which will
unfortunately break ia32el. ia32 ELF binaries on ia64 used to be matched
using binfmt_misc and executed using wrapper. As 32bit binaries are now
matched by binfmt_elf before bindmt_misc kicks in, the wrapper is ignored.
The fix increases precedence of binfmt_misc to the original state.
Signed-off-by: Jan Sembera <jsembera@suse.cz> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Al Viro <viro@ZenIV.linux.org.uk> Cc: Richard Henderson <rth@twiddle.net Cc: <stable@kernel.org> [2.6.everything.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
COMPACTION enables MIGRATION, but MIGRATION spawns a warning if numa or
memhotplug aren't selected. However MIGRATION doesn't depend on them. I
guess it's just trying to be strict doing a double check on who's enabling
it, but it doesn't know that compaction also enables MIGRATION.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Acked-by: Mel Gorman <mel@csn.ul.ie> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pte_same check is reliable only if the swap entry remains pinned (by
the page lock on swapcache). We've also to ensure the swapcache isn't
removed before we take the lock as try_to_free_swap won't care about the
page pin.
One of the possible impacts of this patch is that a KSM-shared page can
point to the anon_vma of another process, which could exit before the page
is freed.
This can leave a page with a pointer to a recycled anon_vma object, or
worse, a pointer to something that is no longer an anon_vma.
[riel@redhat.com: changelog help] Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Acked-by: Hugh Dickins <hughd@google.com> Reviewed-by: Rik van Riel <riel@redhat.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Julia Lawall [Thu, 9 Sep 2010 23:37:50 +0000 (16:37 -0700)]
drivers/mmc/host/imxmmc.c: adjust confusing if indentation
Move the second if (reg & ...) test into the branch indicated by its
indentation. The test was previously always executed after the if
containing that branch, but it was always false unless the if branch was
taken.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Chris Ball <cjb@laptop.org> Cc: Pavel Pisa <ppisa@pikron.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ethan Du [Thu, 9 Sep 2010 23:37:49 +0000 (16:37 -0700)]
omap hsmmc: fix a racing case between kmmcd and omap_hsmmc_suspend
If suspend called when kmmcd is doing host->ops->disable, as kmmcd already
increased host->en_dis_recurs to 1, the mmc_host_enable in suspend
function will return directly without increase the nesting_cnt, which will
cause the followed register access carried out to the disabled host.
mmc_suspend_host will enable host itself. No need to enable host before
it. Also works on kmmcd will get flushed in mmc_suspend_host, enable host
after it will be safe. So make the mmc_host_enable after it.
[cjb: rebase against current Linus] Signed-off-by: Ethan <ethan.too@gmail.com> Signed-off-by: Chris Ball <cjb@laptop.org> Acked-by: Adrian Hunter <adrian.hunter@nokia.com> Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mmc: at91_mci: add missing linux/highmem.h include
Fix the following error:
at91_mci.c: In function 'at91_mci_sg_to_dma':
at91_mci.c:236: error: implicit declaration of function 'kmap_atomic'
at91_mci.c:236: error: 'KM_BIO_SRC_IRQ' undeclared (first use in this function)
at91_mci.c:236: error: (Each undeclared identifier is reported only once
at91_mci.c:236: error: for each function it appears in.)
at91_mci.c:236: warning: assignment makes pointer from integer without a cast
at91_mci.c:252: error: implicit declaration of function 'kunmap_atomic'
at91_mci.c: In function 'at91_mci_post_dma_read':
at91_mci.c:302: error: 'KM_BIO_SRC_IRQ' undeclared (first use in this function)
at91_mci.c:302: warning: assignment makes pointer from integer without a cast
at91_mci.c:317: error: implicit declaration of function 'flush_kernel_dcache_page'
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Chris Ball <cjb@laptop.org> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Andrew Victor <avictor.za@gmail.com> Cc: Wolfgang Muees <wolfgang.mues@auerswald.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kunmap_atomic() takes the cookie, returned by the kmap_atomic() as its
argument and not the page address, used as an argument to kmap_atomic().
This patch fixes the compile error:
In file included from drivers/mmc/host/tmio_mmc.c:37:
drivers/mmc/host/tmio_mmc.h: In function 'tmio_mmc_kunmap_atomic':
drivers/mmc/host/tmio_mmc.h:192: error: negative width in bit-field '<anonymous>'
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Eric Miao <eric.y.miao@gmail.com> Tested-by: Magnus Damm <damm@opensource.se> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously, it was possible for ack_mmc_irqs() to clear pending interrupt
bits in the CTL_STATUS register, even though the interrupt handler had not
been called. This was because of a race that existed when doing a
read-modify-write sequence on CTL_STATUS. After the read step in this
sequence, if an interrupt occurred (causing one of the bits in CTL_STATUS
to be set) the write step would inadvertently clear it.
Observed with the TMIO_STAT_RXRDY bit together with CMD53 on AR6002 and
BCM4318 SDIO cards in polled mode.
This patch eliminates this race by only writing to CTL_STATUS and clearing
the interrupts that were passed as an argument to ack_mmc_irqs()."
[matt@console-pimps.org: rewrote changelog] Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com> Acked-by: Magnus Damm <damm@opensource.se>" Tested-by: Arnd Hannemann <arnd@arndnet.de>" Acked-by: Ian Molton <ian@mnementh.co.uk> Cc: Matt Fleming <matt@console-pimps.org> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Paul Mundt <lethal@linux-sh.org> Cc: <linux-mmc@vger.kernel.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The existing cgroup_attach_task_current_cg() API is called by a thread to
attach another thread to all of its cgroups; this is unsuitable for cases
where a privileged task wants to attach itself to the cgroups of a less
privileged one, since the call must be made from the context of the target
task.
This patch adds a more generic cgroup_attach_task_all() API that allows
both the source task and to-be-moved task to be specified.
cgroup_attach_task_current_cg() becomes a specialization of the more
generic new function.
[menage@google.com: rewrote changelog]
[akpm@linux-foundation.org: address reviewer comments] Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Tested-by: Alex Williamson <alex.williamson@redhat.com> Acked-by: Paul Menage <menage@google.com> Cc: Li Zefan <lizf@cn.fujitsu.com> Cc: Ben Blum <bblum@google.com> Cc: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcov: fix null-pointer dereference for certain module types
The gcov-kernel infrastructure expects that each object file is loaded
only once. This may not be true, e.g. when loading multiple kernel
modules which are linked to the same object file. As a result, loading
such kernel modules will result in incorrect gcov results while unloading
will cause a null-pointer dereference.
This patch fixes these problems by changing the gcov-kernel infrastructure
so that multiple profiling data sets can be associated with one debugfs
entry. It applies to 2.6.36-rc1.
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Reported-by: Werner Spies <werner.spies@thalesgroup.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Moyer [Thu, 9 Sep 2010 23:37:33 +0000 (16:37 -0700)]
O_DIRECT: fix the splitting up of contiguous I/O
commit c2c6ca4 (direct-io: do not merge logically non-contiguous requests)
introduced a bug whereby all O_DIRECT I/Os were submitted a page at a time
to the block layer. The problem is that the code expected
dio->block_in_file to correspond to the current page in the dio. In fact,
it corresponds to the previous page submitted via submit_page_section.
This was purely an oversight, as the dio->cur_page_fs_offset field was
introduced for just this purpose. This patch simply uses the correct
variable when calculating whether there is a mismatch between contiguous
logical blocks and contiguous physical blocks (as described in the
comments).
I also switched the if conditional following this check to an else if, to
ensure that we never call dio_bio_submit twice for the same dio (in
theory, this should not happen, anyway).
I've tested this by running blktrace and verifying that a 64KB I/O was
submitted as a single I/O. I also ran the patched kernel through
xfstests' aio tests using xfs, ext4 (with 1k and 4k block sizes) and btrfs
and verified that there were no regressions as compared to an unpatched
kernel.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Acked-by: Josef Bacik <jbacik@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Chris Mason <chris.mason@oracle.com> Cc: <stable@kernel.org> [2.6.35.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Thu, 9 Sep 2010 23:37:29 +0000 (16:37 -0700)]
rtc-bfin: fix state restoration when resuming
Much (but not all) of the RTC state is kept in the RTC peripheral which
has its own power domain. Periodically (1 HZ), that state is synced from
one power domain to the other (peripheral->core). When we are resuming,
we need to wait for the sync to occur so that we don't get a mismatch of
reading undefined state in the rest of the driver.
Further, once the externally maintained bits have been synced back into
the core, we then need to restore the bits maintained in the core. In our
particular case, that is just the write completion interrupt bit.
If we don't do any of this, working with the RTC causes ~5 second delays
from time to time after waking up due to the write completion interrupt
never firing.
Reported-by: Michael Dean <mdean@aeronix.com> Reported-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Thu, 9 Sep 2010 23:37:27 +0000 (16:37 -0700)]
rtc-bfin: fix inverted logic in suspend path
The int_clear helper takes a bitmask of interrupts to keep, not to
disable. When suspending without wakeup enabled, we want to disable
all interrupts, so use 0 (keep none) instead of -1 (keep all).
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Vrabel [Thu, 9 Sep 2010 23:37:24 +0000 (16:37 -0700)]
mmc: avoid getting CID on SDIO-only cards
The introduction of support for SD combo cards breaks the initialization
of all CSR SDIO chips. The GO_IDLE (CMD0) in mmc_sd_get_cid() causes CSR
chips to be reset (this is non-standard behavior).
When initializing an SDIO card check for a combo card by using the memory
present bit in the R4 response to IO_SEND_OP_COND (CMD5). This avoids the
call to mmc_sd_get_cid() on an SDIO-only card.
Signed-off-by: David Vrabel <david.vrabel@csr.com> Acked-by: Michal Mirolaw <mirq-linux@rere.qmqm.pl> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/home/rmk/linux-2.6-arm: (30 commits)
ARM: Update mach-types
ARM: Partially revert "Auto calculate ZRELADDR and provide option for exceptions"
ARM: Ensure PTE modifications via dma_alloc_coherent are visible
ARM: 6359/1: ep93xx: move clock initialization earlier
Revert "[ARM] pxa: remove now unnecessary dma_needs_bounce()"
ARM: 6352/1: perf: fix event validation
ARM: 6344/1: Mark CPU_32v6K as depended on CPU_V7
ARM: 6343/1: wire up fanotify and prlimit64 syscalls on ARM
ARM: 6330/1: perf: reword comments relating to perf_event_do_pending
ARM: pxa168fb: fix section mismatch
ARM: pxa: Make id const in pwm_probe()
ARM: pxa: fix CI_HSYNC and CI_VSYNC MFP defines for pxa300
ARM: pxa: remove __init from cpufreq_driver->init()
ARM: imx: set cache line size to 64 bytes for i.MX5
mx5/clock: fix clear bit fields issue in _clk_ccgr_disable function
mxc/tzic: add base address when accessing TZIC registers
ARM: mach-shmobile: ap4evb: fix write protect for SDHI1
ARM: mach-shmobile: ap4evb: modify FSI2 ID
ARM: mach-shmobile: do not enable the PLLC2 clock on init
ARM: mach-shmobile: Clock framework comment fix
...
Russell King [Thu, 9 Sep 2010 21:39:41 +0000 (22:39 +0100)]
ARM: Partially revert "Auto calculate ZRELADDR and provide option for exceptions"
Partially revert e69edc7, which introduced automatic zreladdr
support. The change in the way the manual definition is defined
seems to be error and conflict prone. Go back to the original way
we were handling this for the time being, while keeping the automatic
zreladdr facility.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jonathan Corbet [Wed, 8 Sep 2010 22:54:54 +0000 (16:54 -0600)]
lglock: make lg_lock_global() actually lock globally
lg_lock_global() currently only acquires spinlocks for online CPUs, but
it's meant to lock all possible CPUs. Lglock-protected resources may be
associated with removed CPUs - and, indeed, that could happen with the
per-superblock open files lists.
At Nick's suggestion, change for_each_online_cpu() to
for_each_possible_cpu() to protect accesses to those resources.
Cc: Al Viro <viro@ZenIV.linux.org.uk> Acked-by: Nick Piggin <npiggin@kernel.dk> Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Fix hang with modified FIN handling on A0 cards
RDMA/nes: Change state to closing after FIN
RDMA/nes: Fix double CLOSE event indication crash
RDMA/nes: Write correct register write to set TX pause param
RDMA/cxgb3: Don't exceed the max HW CQ depth
Merge branch 'fixes' of git://oss.oracle.com/git/tma/linux-2.6
* 'fixes' of git://oss.oracle.com/git/tma/linux-2.6:
ocfs2: Fix orphan add in ocfs2_create_inode_in_orphan
ocfs2: split out ocfs2_prepare_orphan_dir() into locking and prep functions
ocfs2: allow return of new inode block location before allocation of the inode
ocfs2: use ocfs2_alloc_dinode_update_counts() instead of open coding
ocfs2: split out inode alloc code from ocfs2_mknod_locked
Ocfs2: Fix a regression bug from mainline commit(6b933c8e6f1a2f3118082c455eef25f9b1ac7b45).
ocfs2: Fix deadlock when allocating page
ocfs2: properly set and use inode group alloc hint
ocfs2: Use the right group in nfs sync check.
ocfs2: Flush drive's caches on fdatasync
ocfs2: make __ocfs2_page_mkwrite handle file end properly.
ocfs2: Fix incorrect checksum validation error
ocfs2: Fix metaecc error messages
Faisal Latif [Sat, 14 Aug 2010 21:05:04 +0000 (21:05 +0000)]
RDMA/nes: Change state to closing after FIN
When the driver receives an AE for FIN received, it closes the
connection without changing the state of the connection in the
hardware to closing. By changing the state to closing, hardware will
do a normal close sequence.
Signed-off-by: Faisal Latif <faisal.latif@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Faisal Latif [Sat, 14 Aug 2010 21:04:56 +0000 (21:04 +0000)]
RDMA/nes: Fix double CLOSE event indication crash
During a stress testing in a large cluster, multiple close event are
detected and BUG() is hit in the iWARP core. The cause is that the
active node gave up while waiting for an MPA response from the peer
and tried to close the connection by sending RST. The passive node
driver receives the RST but is waiting for MPA response from the user.
When the MPA accept is received, the driver offloads the connection
and sends a CLOSE event. The driver gets an AE indicating RESET
received and also sends a CLOSE event, hitting a BUG().
Fix this by correcting RESET handling and sending CLOSE events.
Signed-off-by: Faisal Latif <faisal.latif@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, mcheck: Avoid duplicate sysfs links/files for thresholding banks
io-mapping: Fix the address space annotations
x86: Fix the address space annotations of iomap_atomic_prot_pfn()
x86, mm: Fix CONFIG_VMSPLIT_1G and 2G_OPT trampoline
x86, hwmon: Fix unsafe smp_processor_id() in thermal_throttle_add_dev
Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
gcc-4.6: kernel/*: Fix unused but set warnings
mutex: Fix annotations to include it in kernel-locking docbook
pid: make setpgid() system call use RCU read-side critical section
MAINTAINERS: Add RCU's public git tree
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86: Try to handle unknown nmis with an enabled PMU
perf, x86: Fix handle_irq return values
perf, x86: Fix accidentally ack'ing a second event on intel perf counter
oprofile, x86: fix init_sysfs() function stub
lockup_detector: Sync touch_*_watchdog back to old semantics
tracing: Fix a race in function profile
oprofile, x86: fix init_sysfs error handling
perf_events: Fix time tracking for events with pid != -1 and cpu != -1
perf: Initialize callchains roots's childen hits
oprofile: fix crash when accessing freed task structs
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix lock annotations
fuse: flush background queue on connection close
Russell King [Wed, 8 Sep 2010 15:27:56 +0000 (16:27 +0100)]
ARM: Ensure PTE modifications via dma_alloc_coherent are visible
Dave Hylands reports:
| We've observed a problem with dma_alloc_writecombine when the system
| is under heavy load (heavy bus traffic). We've managed to reduce the
| problem to the following snippet, which is run from a kthread in a
| continuous loop:
|
| void *virtAddr;
| dma_addr_t physAddr;
| unsigned int numBytes = 256;
|
| for (;;) {
| virtAddr = dma_alloc_writecombine(NULL,
| numBytes, &physAddr, GFP_KERNEL);
| if (virtAddr == NULL) {
| printk(KERN_ERR "Running out of memory\n");
| break;
| }
|
| /* access DMA memory allocated */
| tmp = virtAddr;
| *tmp = 0x77;
|
| /* free DMA memory */
| dma_free_writecombine(NULL,
| numBytes, virtAddr, physAddr);
|
| ...sleep here...
| }
|
| By itself, the code will run forever with no issues. However, as we
| increase our bus traffic (typically using DMA) then the *tmp = 0x77
| line will eventually cause a page fault. If we add a small delay (a
| few microseconds) before the *tmp = 0x77, then we don't see a page
| fault, even under heavy load.
A dsb() is required after modifying the PTE entries to ensure that they
will always be visible. Add this dsb().
Reported-by: Dave Hylands <dhylands@gmail.com> Tested-by: Dave Hylands <dhylands@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Thomas Gleixner [Tue, 7 Sep 2010 12:46:37 +0000 (14:46 +0200)]
semaphore: Add DEFINE_SEMAPHORE
The full cleanup of init_MUTEX[_LOCKED] and DECLARE_MUTEX has not been
done. Some of the users are real semaphores and we should name them as
such instead of confusing everyone with "MUTEX".
Provide the infrastructure to get finally rid of init_MUTEX[_LOCKED]
and DECLARE_MUTEX.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christoph Hellwig <hch@infradead.org>
LKML-Reference: <20100907125054.795929962@linutronix.de>
Commit 7cfe24947 ("ARM: AMBA: Add pclk support to AMBA bus
infrastructure") changed AMBA bus to handle the PCLK automatically.
However, in EP93xx clock initialization is arch_initcall which is done
later than AMBA device identification. This causes
amba_get_enable_pclk() to fail resulting device where UARTs are not
functional.
So change ep93xx_clock_init() to be postcore_initcall.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 5 Sep 2010 11:19:50 +0000 (12:19 +0100)]
Revert "[ARM] pxa: remove now unnecessary dma_needs_bounce()"
This reverts commit 4fa5518, which causes a compilation regression for
IXP4xx platforms.
Reported-by: Richard Cochran <richardcochran@gmail.com> Acked-by: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mark Fasheh [Fri, 13 Aug 2010 22:15:19 +0000 (15:15 -0700)]
ocfs2: Fix orphan add in ocfs2_create_inode_in_orphan
ocfs2_create_inode_in_orphan() is used by reflink to create the newly
reflinked inode simultaneously in the orphan dir. This allows us to easily
handle partially-reflinked files during recovery cleanup.
We have a problem though - the orphan dir stringifies inode # to determine
a unique name under which the orphan entry dirent can be created. Since
ocfs2_create_inode_in_orphan() needs the space allocated in the orphan dir
before it can allocate the inode, we currently call into the orphan code:
/*
* We give the orphan dir the root blkno to fake an orphan name,
* and allocate enough space for our insertion.
*/
status = ocfs2_prepare_orphan_dir(osb, &orphan_dir,
osb->root_blkno,
orphan_name, &orphan_insert);
Using osb->root_blkno might work fine on unindexed directories, but the
orphan dir can have an index. When it has that index, the above code fails
to allocate the proper index entry. Later, when we try to remove the file
from the orphan dir (using the actual inode #), the reflink operation will
fail.
To fix this, I created a function ocfs2_alloc_orphaned_file() which uses the
newly split out orphan and inode alloc code to figure out what the inode
block number will be (once allocated) and then prepare the orphan dir from
that data.
Signed-off-by: Mark Fasheh <mfasheh@suse.com> Signed-off-by: Tao Ma <tao.ma@oracle.com>
Mark Fasheh [Fri, 13 Aug 2010 22:15:18 +0000 (15:15 -0700)]
ocfs2: split out ocfs2_prepare_orphan_dir() into locking and prep functions
We do this because ocfs2_create_inode_in_orphan() wants to order locking of
the orphan dir with respect to locking of the inode allocator *before*
making any changes to the directory.
Signed-off-by: Mark Fasheh <mfasheh@suse.com> Signed-off-by: Tao Ma <tao.ma@oracle.com>
Mark Fasheh [Fri, 13 Aug 2010 22:15:17 +0000 (15:15 -0700)]
ocfs2: allow return of new inode block location before allocation of the inode
This allows code which needs to know the eventual block number of an inode
but can't allocate it yet due to transaction or lock ordering. For example,
ocfs2_create_inode_in_orphan() currently gives a junk blkno for preparation
of the orphan dir because it can't yet know where the actual inode is placed
- that code is actually in ocfs2_mknod_locked. This is a problem when the
orphan dirs are indexed as the junk inode number will create an index entry
which goes unused (and fails the later removal from the orphan dir). Now
with these interfaces, ocfs2_create_inode_in_orphan() can run the block
group search (and get back the inode block number) *before* any actual
allocation occurs.
Signed-off-by: Mark Fasheh <mfasheh@suse.com> Signed-off-by: Tao Ma <tao.ma@oracle.com>
Mark Fasheh [Fri, 13 Aug 2010 22:15:16 +0000 (15:15 -0700)]
ocfs2: use ocfs2_alloc_dinode_update_counts() instead of open coding
ocfs2_search_chain() makes the same updates as
ocfs2_alloc_dinode_update_counts to the alloc inode. Instead of open coding
the bitmap update, use our helper function.
Signed-off-by: Mark Fasheh <mfasheh@suse.com> Signed-off-by: Tao Ma <tao.ma@oracle.com>
Mark Fasheh [Fri, 13 Aug 2010 22:15:15 +0000 (15:15 -0700)]
ocfs2: split out inode alloc code from ocfs2_mknod_locked
Do this by splitting the bulk of the function away from the inode allocation
code at the very tom of ocfs2_mknod_locked(). Existing callers don't need to
change and won't see any difference. The new function created,
__ocfs2_mknod_locked() will be used shortly.
Signed-off-by: Mark Fasheh <mfasheh@suse.com> Signed-off-by: Tao Ma <tao.ma@oracle.com>
The commit 6b933c8e6f1a2f3118082c455eef25f9b1ac7b45 changed __generic_file_aio_write
to generic_file_buffered_write, which didn't call filemap_{write,wait}_range to flush
the pagecaches when we were falling O_DIRECT writes back to buffered ones. it did hurt
the O_DIRECT semantics somehow in extented odirect writes.
This patch tries to guarantee O_DIRECT writes of 'fall back to buffered' to be correctly
flushed.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com> Signed-off-by: Tao Ma <tao.ma@oracle.com>
Jan Kara [Tue, 24 Aug 2010 12:28:03 +0000 (14:28 +0200)]
ocfs2: Fix deadlock when allocating page
We cannot call grab_cache_page() when holding filesystem locks or with
a transaction started as grab_cache_page() calls page allocation with
GFP_KERNEL flag and thus page reclaim can recurse back into the filesystem
causing deadlocks or various assertion failures. We have to use
find_or_create_page() instead and pass it GFP_NOFS as we do with other
allocations.
Acked-by: Mark Fasheh <mfasheh@suse.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Tao Ma <tao.ma@oracle.com>
Mark Fasheh [Thu, 26 Aug 2010 20:06:50 +0000 (13:06 -0700)]
ocfs2: properly set and use inode group alloc hint
We were setting ac->ac_last_group in ocfs2_claim_suballoc_bits from
res->sr_bg_blkno. Unfortunately, res->sr_bg_blkno is going to be zero under
normal (non-fragmented) circumstances. The discontig block group patches
effectively turned off that feature. Fix this by correctly calculating what
the next group hint should be.
Acked-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com> Tested-by: Goldwyn Rodrigues <rgoldwyn@suse.de> Signed-off-by: Tao Ma <tao.ma@oracle.com>
Jan Kara [Thu, 5 Aug 2010 18:32:45 +0000 (20:32 +0200)]
ocfs2: Flush drive's caches on fdatasync
When 'barrier' mount option is specified, we have to issue a cache flush
during fdatasync(2). We have to do this even if inode doesn't have
I_DIRTY_DATASYNC set because we still have to get written *data* to disk so
that they are not lost in case of crash.
Acked-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Jan Kara <jack@suse.cz> Singed-off-by: Tao Ma <tao.ma@oracle.com>
Tao Ma [Sat, 17 Jul 2010 13:45:49 +0000 (21:45 +0800)]
ocfs2: make __ocfs2_page_mkwrite handle file end properly.
__ocfs2_page_mkwrite now is broken in handling file end.
1. the last page should be the page contains i_size - 1.
2. the len in the last page is also calculated wrong.
So change them accordingly.
Acked-by: Mark Fasheh <mfasheh@suse.com> Signed-off-by: Tao Ma <tao.ma@oracle.com>
Sunil Mushran [Thu, 12 Aug 2010 23:24:26 +0000 (16:24 -0700)]
ocfs2: Fix incorrect checksum validation error
For local mounts, ocfs2_read_locked_inode() calls ocfs2_read_blocks_sync() to
read the inode off the disk. The latter first checks to see if that block is
cached in the journal, and, if so, returns that block. That is ok.
But ocfs2_read_locked_inode() goes wrong when it tries to validate the checksum
of such blocks. Blocks that are cached in the journal may not have had their
checksum computed as yet. We should not validate the checksums of such blocks.
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
ima: always maintain counters
AppArmor: Fix locking from removal of profile namespace
AppArmor: Fix splitting an fqname into separate namespace and profile names
AppArmor: Fix security_task_setrlimit logic for 2.6.36 changes
AppArmor: Drop hack to remove appended " (deleted)" string
Mimi Zohar [Tue, 31 Aug 2010 13:38:51 +0000 (09:38 -0400)]
ima: always maintain counters
commit 8262bb85da allocated the inode integrity struct (iint) before any
inodes were created. Only after IMA was initialized in late_initcall were
the counters updated. This patch updates the counters, whether or not IMA
has been initialized, to resolve 'imbalance' messages.
This patch fixes the bug as reported in bugzilla: 15673. When the i915
is builtin, the ring_buffer is initialized before IMA, causing the
imbalance message on suspend.
Reported-by: Thomas Meyer <thomas@m3y3r.de> Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com> Tested-by: Thomas Meyer <thomas@m3y3r.de> Tested-by: David Safford<safford@watson.ibm.com> Cc: Stable Kernel <stable@kernel.org> Signed-off-by: James Morris <jmorris@namei.org>
John Johansen [Sat, 28 Aug 2010 01:33:29 +0000 (18:33 -0700)]
AppArmor: Fix locking from removal of profile namespace
The locking for profile namespace removal is wrong, when removing a
profile namespace, it needs to be removed from its parent's list.
Lock the parent of namespace list instead of the namespace being removed.
Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: James Morris <jmorris@namei.org>
John Johansen [Sat, 28 Aug 2010 01:33:28 +0000 (18:33 -0700)]
AppArmor: Fix splitting an fqname into separate namespace and profile names
As per Dan Carpenter <error27@gmail.com>
If we have a ns name without a following profile then in the original
code it did "*ns_name = &name[1];". "name" is NULL so "*ns_name" is
0x1. That isn't useful and could cause an oops when this function is
called from aa_remove_profiles().
Beyond this the assignment of the namespace name was wrong in the case
where the profile name was provided as it was being set to &name[1]
after name = skip_spaces(split + 1);
Move the ns_name assignment before updating name for the split and
also add skip_spaces, making the interface more robust.
Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: James Morris <jmorris@namei.org>
John Johansen [Mon, 6 Sep 2010 17:10:20 +0000 (10:10 -0700)]
AppArmor: Fix security_task_setrlimit logic for 2.6.36 changes
2.6.36 introduced the abilitiy to specify the task that is having its
rlimits set. Update mediation to ensure that confined tasks can only
set their own group_leader as expected by current policy.
Add TODO note about extending policy to support setting other tasks
rlimits.
Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: James Morris <jmorris@namei.org>
John Johansen [Sat, 28 Aug 2010 01:33:26 +0000 (18:33 -0700)]
AppArmor: Drop hack to remove appended " (deleted)" string
The 2.6.36 kernel has refactored __d_path() so that it no longer appends
" (deleted)" to unlinked paths. So drop the hack that was used to detect
and remove the appended string.
Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: James Morris <jmorris@namei.org>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: bus speed strings should be const
PCI hotplug: Fix build with CONFIG_ACPI unset
PCI: PCIe: Remove the port driver module exit routine
PCI: PCIe: Move PCIe PME code to the pcie directory
PCI: PCIe: Disable PCIe port services during port initialization
PCI: PCIe: Ask BIOS for control of all native services at once
ACPI/PCI: Negotiate _OSC control bits before requesting them
ACPI/PCI: Do not preserve _OSC control bits returned by a query
ACPI/PCI: Make acpi_pci_query_osc() return control bits
ACPI/PCI: Reorder checks in acpi_pci_osc_control_set()
PCI: PCIe: Introduce commad line switch for disabling port services
PCI: PCIe AER: Introduce pci_aer_available()
x86/PCI: only define pci_domain_nr if PCI and PCI_DOMAINS are set
PCI: provide stub pci_domain_nr function for !CONFIG_PCI configs
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: Make fiemap work with sparse files
xfs: prevent 32bit overflow in space reservation
xfs: Disallow 32bit project quota id
xfs: improve buffer cache hash scalability
Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md:
md: resolve confusion of MD_CHANGE_CLEAN
md: don't clear MD_CHANGE_CLEAN in md_update_sb() for external arrays
Move .gitignore from drivers/md to lib/raid6
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: fix a mismatch between code and comment
percpu: fix a memory leak in pcpu_extend_area_map()
percpu: add __percpu notations to UP allocator
percpu: handle __percpu notations in UP accessors
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
pkt_sched: Fix lockdep warning on est_tree_lock in gen_estimator
ipvs: avoid oops for passive FTP
Revert "sky2: don't do GRO on second port"
gro: fix different skb headrooms
bridge: Clear INET control block of SKBs passed into ip_fragment().
3c59x: Remove incorrect locking; correct documented lock hierarchy
sky2: don't do GRO on second port
ipv4: minor fix about RPF in help of Kconfig
xfrm_user: avoid a warning with some compiler
net/sched/sch_hfsc.c: initialize parent's cl_cfmin properly in init_vf()
pxa168_eth: fix a mdiobus leak
net sched: fix kernel leak in act_police
vhost: stop worker only if created
MAINTAINERS: Add ehea driver as Supported
ath9k_hw: fix parsing of HT40 5 GHz CTLs
ath9k_hw: Fix EEPROM uncompress block reading on AR9003
wireless: register wiphy rfkill w/o holding cfg80211_mutex
netlink: Make NETLINK_USERSOCK work again.
irda: Correctly clean up self->ias_obj on irda_bind() failure.
wireless extensions: fix kernel heap content leak
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: wlan-ng: Explicitly set some fields in cfg80211 interface
Staging: octeon: depends on NETDEVICES
Staging: spectra: depend on X86_MRST
Staging: zram: free device memory when init fails
Staging: rt2870sta: Add more device IDs from vendor drivers
staging: comedi das08_cs.c: Fix io_req_t conversion
staging: spectra needs <linux/slab.h>
staging: hv: Fixed lockup problem with bounce_buffer scatter list
staging: hv: Increased storvsc ringbuffer and max_io_requests
staging: hv: Fixed the value of the 64bit-hole inside ring buffer
staging: hv: Fixed bounce kmap problem by using correct index
staging: hv: Fix missing functions for net_device_ops
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: ftdi_sio: Added custom PIDs for ChamSys products
USB: cdc-acm: Fixing crash when ACM probing interfaces with no endpoint descriptors.
USB: cdc-acm: Add pseudo modem without AT command capabilities
USB: cxacru: Use a bulk/int URB to access the command endpoint
usb: serial: mos7840: Add USB IDs to support more B&B USB/RS485 converters.
USB: cdc-acm: Adding second ACM channel support for various Nokia and one Samsung phones
usb: serial: mos7840: Add USB ID to support the B&B Electronics USOPTL4-2P.
USB: ssu100: turn off debug flag
usb: allow drivers to use allocated bandwidth until unbound
USB: cp210x usb driver: add USB_DEVICE for Pirelli DP-L10 mobile.
USB: cp210x: Add B&G H3000 link cable ID
USB: CP210x Add new device ID
USB: option: fix incorrect novatel entries
USB: Fix kernel oops with g_ether and Windows
USB: rndis: section mismatch fix
USB: ehci-ppc-of: problems in unwind
USB: s3c-hsotg: Remove DEBUG define
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: fix tty_line must not be equal to number of allocated tty pointers in tty driver
serial: bfin_sport_uart: restore transmit frame sync fix
serial: fix port type conflict between NS16550A & U6_16550A
MAINTAINERS: orphan isicom
vt: Fix console corruption on driver hand-over.
Merge branch 'linux-next' of git://git.infradead.org/ubi-2.6
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: do not oops when erroneous PEB is scheduled for scrubbing
UBI: fix kconfig unmet dependency
UBI: fix forward compatibility
UBI: eliminate update of list_for_each_entry loop cursor
Merge branch 'drm-intel-fixes' of git://anongit.freedesktop.org/~ickle/drm-intel
* 'drm-intel-fixes' of git://anongit.freedesktop.org/~ickle/drm-intel: (25 commits)
intel_agp,i915: Add more sandybridge graphics device ids
drm/i915: Enable MI_FLUSH on Sandybridge
agp/intel: Fix cache control for Sandybridge
agp/intel: use #ifdef idiom for intel-agp.h
agp/intel: fix physical address mask bits for sandybridge
drm/i915: Prevent double dpms on
drm/i915: Avoid use of uninitialised values when disabling panel-fitter
drm/i915: Avoid pageflipping freeze when we miss the flip prepare interrupt
drm/i915: Tightly scope intel_encoder to prevent invalid use
drm/i915: Allocate the PCI resource for the MCHBAR
drm/i915/dp: Really try 5 times before giving up.
drm/i915/sdvo: Restore guess of the DDC bus in absence of VBIOS
drm/i915/dp: Boost timeout for enabling transcoder to 100ms
drm/i915: Re-use set_base_atomic to share setting of the display registers
drm/i915: Fix offset page-flips on i965+
drm/i915: Include a generation number in the device info
i915: return -EFAULT if copy_to_user fails
i915: return -EFAULT if copy_to_user fails
agp/intel: Promote warning about failure to setup flush to error.
drm/i915: overlay on gen2 can't address above 1G
...
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: Do not force 1024x768 modes on unknown connectors
drm/kms: Add a module parameter to disable polling
drm/radeon/kms: fix tv-out on avivo asics
drm/radeon/kms/evergreen: fix gpu hangs in userspace accel code
drm/nv50: initialize ramht_refs list for faked 0 channel
drm/nouveau: Don't take struct_mutex around the pushbuf IOCTL.
drm/nouveau: Take fence spinlock before reading the last sequence.
drm/radeon/kms/evergreen: work around bad data in some i2c tables
drm/radeon/kms: properly set crtc high base on r7xx
drm/radeon/kms: fix tv module parameter
drm/radeon/kms: force legacy pll algo for RV515 LVDS
drm/radeon/kms: remove useless clock code
drm/radeon/kms: fix a regression on r7xx AGP due to the HDP flush fix
drm/radeon/kms: use tracked values for sclk and mclk
David Howells [Tue, 31 Aug 2010 15:52:21 +0000 (16:52 +0100)]
h8300: Fix missing consts in kernel_execve()
Fix missing consts in h8300's kernel_execve():
arch/h8300/kernel/sys_h8300.c: In function 'kernel_execve':
arch/h8300/kernel/sys_h8300.c:59: warning: initialization from incompatible pointer type
arch/h8300/kernel/sys_h8300.c:60: warning: initialization from incompatible pointer type
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Tue, 31 Aug 2010 15:52:16 +0000 (16:52 +0100)]
h8300: Fix die()
Fix h8300's die() to take care of a number of problems:
CC arch/h8300/kernel/traps.o
In file included from arch/h8300/include/asm/bitops.h:10,
from include/linux/bitops.h:22,
from include/linux/kernel.h:17,
from include/linux/sched.h:54,
from arch/h8300/kernel/traps.c:18:
arch/h8300/include/asm/system.h:136: warning: 'struct pt_regs' declared inside parameter list
arch/h8300/include/asm/system.h:136: warning: its scope is only this definition or declaration, which is probably not what you want
arch/h8300/kernel/traps.c:100: error: conflicting types for 'die'
arch/h8300/include/asm/system.h:136: error: previous declaration of 'die' was here
make[2]: *** [arch/h8300/kernel/traps.o] Error 1
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Tue, 31 Aug 2010 15:52:11 +0000 (16:52 +0100)]
h8300: IRQ flags should be stored in an unsigned long
Fix h8300's asm/atomic.h to store the IRQ flags in an unsigned long to deal
with warnings of the following type:
arch/h8300/include/asm/atomic.h: In function 'atomic_add_return':
arch/h8300/include/asm/atomic.h:22: warning: comparison of distinct pointer types lacks a cast
arch/h8300/include/asm/atomic.h:24: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Valerie Aurora [Thu, 26 Aug 2010 18:07:22 +0000 (11:07 -0700)]
VFS: Sanity check mount flags passed to change_mnt_propagation()
Sanity check the flags passed to change_mnt_propagation(). Exactly
one flag should be set. Return EINVAL otherwise.
Userspace can pass in arbitrary combinations of MS_* flags to mount().
do_change_type() is called if any of MS_SHARED, MS_PRIVATE, MS_SLAVE,
or MS_UNBINDABLE is set. do_change_type() clears MS_REC and then
calls change_mnt_propagation() with the rest of the user-supplied
flags. change_mnt_propagation() clearly assumes only one flag is set
but do_change_type() does not check that this is true. For example,
mount() with flags MS_SHARED | MS_RDONLY does not actually make the
mount shared or read-only but does clear MNT_UNBINDABLE.
David Bartly reported that fuse can hang in fuse_get_req_nofail() when
the connection to the filesystem server is no longer active.
If bg_queue is not empty then flush_bg_queue() called from
request_end() can put more requests on to the pending queue. If this
happens while ending requests on the processing queue then those
background requests will be queued to the pending list and never
ended.
Another problem is that fuse_dev_release() didn't wake up processes
sleeping on blocked_waitq.
Solve this by:
a) flushing the background queue before calling end_requests() on the
pending and processing queues
b) setting blocked = 0 and waking up processes waiting on
blocked_waitq()
Thanks to David for an excellent bug report.
Reported-by: David Bartley <andareed@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> CC: stable@kernel.org
Zhenyu Wang [Tue, 7 Sep 2010 05:45:32 +0000 (13:45 +0800)]
intel_agp,i915: Add more sandybridge graphics device ids
New pci ids for GT2 and GT2+ on desktop and mobile sandybridge,
and graphics device ids for server sandybridge. Also rename original
ids string to reflect GT1 version.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com> Cc: stable@kernel.org Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
projects / mirror_ubuntu-disco-kernel.git / log