James Chapman [Wed, 3 Jan 2018 22:48:06 +0000 (22:48 +0000)]
l2tp: remove configurable payload offset
If L2TP_ATTR_OFFSET is set to a non-zero value in L2TPv3 tunnels, it
results in L2TPv3 packets being transmitted which might not be
compliant with the L2TPv3 RFC. This patch has l2tp ignore the offset
setting and send all packets with no offset.
In more detail:
L2TPv2 supports a variable offset from the L2TPv2 header to the
payload. The offset value is indicated by an optional field in the
L2TP header. Our L2TP implementation already detects the presence of
the optional offset and skips that many bytes when handling data
received packets. All transmitted packets are always transmitted with
no offset.
L2TPv3 has no optional offset field in the L2TPv3 packet
header. Instead, L2TPv3 defines optional fields in a "Layer-2 Specific
Sublayer". At the time when the original L2TP code was written, there
was talk at IETF of offset being implemented in a new Layer-2 Specific
Sublayer. A L2TP_ATTR_OFFSET netlink attribute was added so that this
offset could be configured and the intention was to allow it to be
also used to set the tx offset for L2TPv2. However, no L2TPv3 offset
was ever specified and the L2TP_ATTR_OFFSET parameter was forgotten
about.
Setting L2TP_ATTR_OFFSET results in L2TPv3 packets being transmitted
with the specified number of bytes padding between L2TPv3 header and
payload. This is not compliant with L2TPv3 RFC3931. This change
removes the configurable offset altogether while retaining
L2TP_ATTR_OFFSET for backwards compatibility. Any L2TP_ATTR_OFFSET
value is ignored.
Signed-off-by: James Chapman <jchapman@katalix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
James Chapman [Wed, 3 Jan 2018 22:48:04 +0000 (22:48 +0000)]
l2tp: revert "l2tp: add peer_offset parameter"
Revert commit f15bc54eeecd ("l2tp: add peer_offset parameter"). This
is removed because it is adding another configurable offset and
configurable offsets are being removed.
Signed-off-by: James Chapman <jchapman@katalix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Wed, 3 Jan 2018 22:40:11 +0000 (23:40 +0100)]
net/mlx5e: hide an unused variable
The uplink_rpriv variable was added at the start of the function but
only used inside of an #ifdef:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c: In function 'mlx5e_route_lookup_ipv6':
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:1549:25: error: unused variable 'uplink_rpriv' [-Werror=unused-variable]
This moves the declaration into that #ifdef as well.
Fixes: 5ed99fb421d4 ("net/mlx5e: Move ethernet representors data into separate struct") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 4 Jan 2018 19:33:29 +0000 (14:33 -0500)]
Merge tag 'mac80211-next-for-davem-2018-01-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have things all over the place, no point listing them.
One thing is notable: I applied two patches and later
reverted them - we'll get back to that once all the driver
situation is sorted out.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com> Signed-off-by: Satish Baddipadige <satish.baddipadige@broadcom.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 3 Jan 2018 17:18:02 +0000 (12:18 -0500)]
Merge branch 'nfp-flower-repr-link-state'
Jakub Kicinski says:
====================
nfp: flower: repr link state
Dirk says:
This series provides two updates towards the link state of reprs in
the flower nfp app.
Patch #1 improves the way link state is reported for reprs. Instead of
starting with an assumed 'UP' state, always assume the link state is
'DOWN' and then modify this only on events received from firmware.
Patch #2 adds a new nfp_app hook, repr_preclean. This callback is
executed before reprs are removed from the app context and is executed
per repr.
Patch #3 implements the new REIFY control message, used to indicate
when reprs are created and destroyed. Firmware uses these messages
to prevent communication about any particular port when the driver
doesn't know about the repr yet or anymore.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The PORT_REIFY message indicates whether reprs have been created or
when they are about to be destroyed. This is necessary so firmware
can know which state the driver is in, e.g. the firmware will not send
any control messages related to ports when the reprs are destroyed.
This prevents nuisance warning messages printed whenever the firmware
sends updates for non-existent reprs.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Just before a repr is cleaned up, we give the app a chance to perform
some preclean configuration while the reprs pointer is still configured
for the app.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
nfp: flower: obtain repr link state only from firmware
Instead of starting up reprs assuming that there is link, only respond
to the link state reported by firmware.
Furthermore, ensure link is down after repr netdevs are created.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 2 Jan 2018 16:40:26 +0000 (17:40 +0100)]
net: mdio: Only perform gpio reset for PHYs
Ethernet switch on the MDIO bus have historically performed their own
handling of the GPIO reset line. The resent patch to have the MDIO
core handle the reset has broken the switch drivers, in that they
cannot claim the GPIO. Some switch drivers need more control over the
GPIO line than what the MDIO core provides. So restore the historical
behaviour by only performing a reset of PHYs, not switches.
Fixes: bafbdd527d56 ("phylib: Add device reset GPIO support") Reported-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 3 Jan 2018 16:00:24 +0000 (11:00 -0500)]
Merge branch 'net-Resolve-races-in-phy-accessors'
Russell King says:
====================
Resolve races in phy accessors
This series resolves races with various accesses to PHY registers.
The first five patches are necessary before we add phylink support
to mvneta, the remaining three are merely cleanups for unobserved
races, and hence are less critical.
There are two possible classes of races that can occur: where we
write to a page register that changes the meaning of a group of
other registers, and where we read-modify-write a register.
Resolve these races by performing the accesses under the mdio bus
lock, ensuring that no other user can access the bus while the
series of atomic operations are being performed.
These patches have been posted before, and have been modified
along the lines of previous feedback:
- The third patch was originally reviewed by Florian, but as I've
added __phy_modify() to it, I've removed that attributation.
- Included generic page-based accessors as suggested last time
around.
- Since we have the unlocked __phy_modify() in this patch series,
it is sensible to include the changes for this to marvell.c -
these accessors have to change anyway to avoid deadlocks on the
mdio bus lock.
I haven't been able to test the at803x.c changes yet beyond compile
testing - although I do have systems with an ar8035 PHY. However,
they should be straight forward to review.
This is targetted for net-next because the races have not been
found in existing drivers, but have been observed with phylink
integrated into mvneta - that's not to say that the races do not
exist today, they are just unobserved (probably through lack of
rigorous enough testing.) The race provoking condition is detailed
in patch 5.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 2 Jan 2018 10:58:58 +0000 (10:58 +0000)]
net: phy: convert read-modify-write to phy_modify()
Convert read-modify-write sequences in at803x, Marvell and core phylib
to use phy_modify() to ensure safety.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 2 Jan 2018 10:58:53 +0000 (10:58 +0000)]
net: phy: add phy_modify() accessor
Add phy_modify() convenience accessor to complement the mdiobus
counterpart.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 2 Jan 2018 10:58:48 +0000 (10:58 +0000)]
net: phy: marvell: fix paged access races
For paged accesses to be truely safe, we need to hold the bus lock to
prevent anyone else gaining access to the registers while we modify
them.
The phydev->lock mutex does not do this: userspace via the MII ioctl
can still sneak in and read or write any register while we are on a
different page, and the suspend/resume methods can be called by a
thread different to the thread polling the phy status.
Races have been observed with mvneta on SolidRun Clearfog with phylink,
particularly between the phylib worker reading the PHYs status, and
the thread resuming mvneta, calling phy_start() which then calls
through to m88e1121_config_aneg_rgmii_delays(), which tries to
read-modify-write the MSCR register:
The result of this is we end up writing the copper page register 21,
which causes the copper PHY to be disabled, and the link partner sees
the link immediately go down.
Solve this by taking the bus lock instead of the PHY lock, thereby
preventing other accesses to the PHY while we are accessing other PHY
pages.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 2 Jan 2018 10:58:43 +0000 (10:58 +0000)]
net: phy: add paged phy register accessors
Add a set of paged phy register accessors which are inherently safe in
their design against other accesses interfering with the paged access.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 2 Jan 2018 10:58:37 +0000 (10:58 +0000)]
net: phy: add unlocked accessors
Add unlocked versions of the bus accessors, which allows access to the
bus with all the tracing. These accessors validate that the bus mutex
is held, which is a basic requirement for all mii bus accesses.
Also added is a read-modify-write unlocked accessor with the same
locking requirements.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 2 Jan 2018 10:58:32 +0000 (10:58 +0000)]
net: phy: use unlocked accessors for indirect MMD accesses
Use unlocked accessors for indirect MMD accesses to clause 22 PHYs.
This permits tracing of these accesses.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 2 Jan 2018 10:58:27 +0000 (10:58 +0000)]
net: mdiobus: add unlocked accessors
Add unlocked versions of the bus accessors, which allows access to the
bus with all the tracing. These accessors validate that the bus mutex
is held, which is a basic requirement for all mii bus accesses.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Collect TX rate limiting related information in UP CIM logs.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 3 Jan 2018 15:38:54 +0000 (10:38 -0500)]
Merge branch 'mvneta-phylink'
Russell King says:
====================
Convert mvneta to phylink
This series converts mvneta to use phylink, which is necessary to
support the SFP cages on SolidRun's Clearfog platform. This series just
converts mvneta without adding the DT parts - having discussed with
Andrew, we believe we're too close to the merge window to submit that
patch.
I've split the "net: mvneta: convert to phylink" patch up to make it
easier to review, and in doing so, spotted some minor corner cases that
needed to be fixed along the way.
This series depends on the previously merged phylink patches in netdev,
along with the recently reviewed 7 patch series "Resolve races in phy
accessors" without which, the race described in patch 5 of that series
is very evident when triggering a dummy hibernate cycle.
This series also illustrates how to convert mvpp2 to phylink.
mvneta is the only user of the fixed_phy_update_state() API, and this
becomes redundant with the conversion.
It would be good to get this series not only reviewed, but also
independently tested to ensure that I haven't missed anything - I only
have the Clearfog platform to test on, and that doesn't support all the
different interface modes that mvneta supports.
A particularly interesting side effect of this series is that DSA
switches no longer need the "CPU" port and DSA facing MAC ethernet
instance to be marked as a fixed link anymore with mvneta - we can use
1000BaseX mode, and the DSA to CPU link will use the 802.3z negotiation
to determine the link properties without needing the link parameters to
be explicitly stated in DT - that is a subject of a future patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mvneta is the only user of fixed_phy_update_state(), which has been
converted to use phylink instead. Remove fixed_phy_update_state().
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
The PSC sync change interrupt can fire multiple times while the link is
down, which is caused by noise on the serdes lines. As this isn't
information we make use of, it's pointless having the interrupt enabled.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 2 Jan 2018 17:24:34 +0000 (17:24 +0000)]
net: mvneta: ensure PM paths take the rtnl lock
The netdev core always ensures that the rtnl lock is held while calling
the ndo_open() and ndo_stop() methods. However, the suspend/resume paths
do not hold the rtnl lock. phylink will expect the rtnl lock to be held
when the MAC driver calls it, so we end up with kernel warnings. Take
the lock to ensure that these functions are called in a consistent
manner.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sun, 31 Dec 2017 18:41:36 +0000 (21:41 +0300)]
sh_eth: kill redundant check in the probe() method
Browsing thru the driver disassembly, I noticed that gcc was able to
figure out that the 'ndev' pointer is always non-NULL when calling
free_netdev() on the probe() method's error path and thus skip that
redundant NULL check... gcc is smart, be like gcc! :-)
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sun, 31 Dec 2017 18:41:35 +0000 (21:41 +0300)]
ravb: kill redundant check in the probe() method
Browsing thru the driver disassembly, I noticed that gcc was able to
figure out that the 'ndev' pointer is always non-NULL when calling
free_netdev() on the probe() method's error path and thus skip that
redundant NULL check... gcc is smart, be like gcc! :-)
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net>
Himanshu Jha [Sun, 31 Dec 2017 12:27:29 +0000 (17:57 +0530)]
liquidio: Use zeroing memory allocator than allocator/memset
Use vzalloc for allocating zeroed memory and remove unnecessary
memset function.
Done using Coccinelle. Generated-by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
0-day tested with no failures.
Suggested-by: Luis R. Rodriguez <mcgrof@kernel.org> Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Himanshu Jha [Sat, 30 Dec 2017 15:44:57 +0000 (21:14 +0530)]
ethernet/broadcom: Use zeroing memory allocator than allocator/memset
Use dma_zalloc_coherent for allocating zeroed
memory and remove unnecessary memset function.
Done using Coccinelle. Generated-by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
0-day tested with no failures.
Suggested-by: Luis R. Rodriguez <mcgrof@kernel.org> Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Himanshu Jha [Sat, 30 Dec 2017 15:37:04 +0000 (21:07 +0530)]
qed: Use zeroing memory allocator than allocator/memset
Use dma_zalloc_coherent and vzalloc for allocating zeroed
memory and remove unnecessary memset function.
Done using Coccinelle. Generated-by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
0-day tested with no failures.
Suggested-by: Luis R. Rodriguez <mcgrof@kernel.org> Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com> Acked-by: Tomer Tayar <Tomer.Tayar@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: stmmac: Couple of debug prints improvements
While working on a particular problem, I had to turn on debug prints and found
them to be useful, but could deserve some improvements in order to help debug
situations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sat, 30 Dec 2017 03:56:33 +0000 (19:56 -0800)]
net: stmmac: Allow debug prints of frame_len/COE
There is no reason not to allow printing the frame_len/COE value and put
that under a check for ETH_FRAME_LEN, drop it so we can see what the
descriptor reports.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sat, 30 Dec 2017 03:56:32 +0000 (19:56 -0800)]
net: stmmac: Pad ring number with zeroes in display_ring()
Make the printing of the ring number consistent and properly aligned by
padding the ring number with up to 3 zeroes, which covers the maximum
ring size. This makes it a lot easier to see outliers in debug prints.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 29 Dec 2017 19:05:45 +0000 (11:05 -0800)]
net: dsa: Fix dsa_legacy_register() return value
We need to make the dsa_legacy_register() stub return 0 in order for
dsa_init_module() to successfully register and continue registering the
ETH_P_XDSA packet handler.
Fixes: 2a93c1a3651f ("net: dsa: Allow compiling out legacy support") Reported-by: Egil Hjelmeland <privat@egil-hjelmeland.no> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 3 Jan 2018 02:45:32 +0000 (21:45 -0500)]
Merge branch 'further-sfp-phylink-updates'
Russell King says:
====================
further sfp/phylink updates
This series:
- cleans up printing of module information
- improves the transceiver capability decoding, getting rid of the
guessing by connector type, improves direct-attach cable support
and adds support for 1G Base-PX and Base-BX10 modules.
- cleans up phylink_sfp_module_insert()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 29 Dec 2017 12:15:28 +0000 (12:15 +0000)]
sfp: improve support for direct-attach copper cables
Improve the support for direct-attach copper so that we avoid kernel
warning messages, and report the appropriate PORT_DA type to userspace.
Direct Attach cables can use a number of protocols depending on their
range of speeds.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 29 Dec 2017 12:15:12 +0000 (12:15 +0000)]
sfp: use precision to print non-null terminated strings
Rather than memcpy()'ing the strings and null terminate them, printf
allows non-NULL terminated strings provided the precision is not more
than the size of the buffer. Use this form to print the basic module
information rather than copying and terminating the strings.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 2 Jan 2018 20:00:50 +0000 (15:00 -0500)]
Merge branch 'marvell10g-phy-updates'
Russell King says:
====================
marvell10g updates
This series:
- adds MDI/MDIX reporting
- adds support for 10/100Mbps half-duplex link modes
- adds a comment describing the setup on VF610 ZII boards (where
the phy interface mode doesn't change.)
- cleans up the phy interace mode switching
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 29 Dec 2017 12:46:43 +0000 (12:46 +0000)]
net: phy: marvell10g: add support for half duplex 100M and 10M
Add support for half-duplex 100M and 10M copper connections by parsing
the advertisment results rather than trying to decode the negotiated
speed from one of the PHYs "vendor" registers. This allows us to
decode the duplex as well, which means we can support half-duplex mode
for the slower speeds.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 29 Dec 2017 12:46:38 +0000 (12:46 +0000)]
net: phy: add helper to convert negotiation result to phy settings
Add a helper to convert the result of the autonegotiation advertisment
into the PHYs speed and duplex settings. If the result is full duplex,
also extract the pause mode settings from the link partner advertisment.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 29 Dec 2017 12:46:32 +0000 (12:46 +0000)]
net: phy: marvell10g: clean up interface mode switching
Centralise the PHY interface mode switching, rather than having it in
two places.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 29 Dec 2017 12:46:27 +0000 (12:46 +0000)]
net: phy: marvell10g: add MDI swap reporting
Add reporting of the MDI swap to the Marvell 10G PHY driver by providing
a generic implementation for the standard 10GBASE-T pair swap register
and polarity register. We also support reading the MDI swap status for
1G and below from a PCS register.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 29 Dec 2017 12:46:22 +0000 (12:46 +0000)]
net: phy: marvell10g: update header comments
Update header comments to indicate the newly found behaviour with XAUI
interfaces.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Fri, 29 Dec 2017 09:11:11 +0000 (17:11 +0800)]
net: hns: add ACPI mode support for ethtool -p
The locate operation interface of fiber port can only
work with DT mode. Add a new interface to control the
locate led for ACPI mode.
Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Tested-by: Zhou Wang <wangzhou1@hisilicon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Fri, 29 Dec 2017 07:18:04 +0000 (12:48 +0530)]
cxgb4: Check alignment constraint for T6
Update the check for setting IPV4 filters and align filter_id
to multiple of 2, only for IPv6 filters in case of T6.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com> Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 2 Jan 2018 19:35:12 +0000 (14:35 -0500)]
Merge branch 'ena-next'
Netanel Belgazal says:
====================
update ENA driver to version 1.5.0
This patchset contains two changes:
* Add a robust mechanism for detection of stuck Rx/Tx rings due to
missed or misrouted MSI-X
* Increase the driver version to 1.5.0
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Netanel Belgazal [Thu, 28 Dec 2017 21:31:30 +0000 (21:31 +0000)]
net: ena: add detection and recovery mechanism for handling missed/misrouted MSI-X
A mechanism for detection of stuck Rx/Tx rings due to missed or
misrouted interrupts.
Check if there are unhandled completion descriptors before the first
MSI-X interrupt arrived.
The check is per queue and per interrupt vector.
Once such condition is detected, driver and device reset is scheduled.
Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This series is v7 of the replacement of jprobe usage with trace
events. This version fixes net/dccp/trace.h to avoid sparse
warning. Since the TP_STORE_ADDR_PORTS macro can be shared
with trace/events/tcp.h, it also introduce a new common header
file and move the definition of that macro.
Previous version is here;
https://lkml.org/lkml/2017/12/28/7
Changes from v6:
[5/6]: Avoid preprocessor directives in tracepoint macro args
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Masami Hiramatsu [Fri, 29 Dec 2017 02:48:25 +0000 (11:48 +0900)]
net: dccp: Remove dccpprobe module
Remove DCCP probe module since jprobe has been deprecated.
That function is now replaced by dccp/dccp_probe trace-event.
You can use it via ftrace or perftools.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Masami Hiramatsu [Fri, 29 Dec 2017 02:47:20 +0000 (11:47 +0900)]
net: sctp: Remove debug SCTP probe module
Remove SCTP probe module since jprobe has been deprecated.
That function is now replaced by sctp/sctp_probe and
sctp/sctp_probe_path trace-events.
You can use it via ftrace or perftools.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Masami Hiramatsu [Fri, 29 Dec 2017 02:46:51 +0000 (11:46 +0900)]
net: sctp: Add SCTP ACK tracking trace event
Add SCTP ACK tracking trace event to trace the changes of SCTP
association state in response to incoming packets.
It is used for debugging SCTP congestion control algorithms,
and will replace sctp_probe module.
Note that this event a bit tricky. Since this consists of 2
events (sctp_probe and sctp_probe_path) so you have to enable
both events as below.
Masami Hiramatsu [Fri, 29 Dec 2017 02:46:21 +0000 (11:46 +0900)]
net: tcp: Remove TCP probe module
Remove TCP probe module since jprobe has been deprecated.
That function is now replaced by tcp/tcp_probe trace-event.
You can use it via ftrace or perftools.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Masami Hiramatsu [Fri, 29 Dec 2017 02:45:51 +0000 (11:45 +0900)]
net: tcp: Add trace events for TCP congestion window tracing
This adds an event to trace TCP stat variables with
slightly intrusive trace-event. This uses ftrace/perf
event log buffer to trace those state, no needs to
prepare own ring-buffer, nor custom user apps.
David S. Miller [Tue, 2 Jan 2018 18:59:17 +0000 (13:59 -0500)]
Merge branch 'qed-Advance-to-FW-8.33.1.0'
Tomer Tayar says:
====================
qed*: Advance to FW 8.33.1.0
This series advances all qed* drivers to use firmware 8.33.1.0 which brings
new capabilities and initial support of new HW. The changes are mostly in
qed, and include changes in the FW interface files, as well as updating the
FW initialization and debug collection code. The protocol drivers have
minor functional changes for this firmware.
Patch 1 Rearranges and refactors the FW interface files in preparation of
the new FW (no functional change).
Patch 2 Prepares the code for support of new HW (no functional change).
Patch 3 Actual utilization of the new FW.
Patch 4 Advances drivers' version.
v3->v4:
Fix a compilation issue which was reported by krobot (dependency on CRC8).
v2->v3:
Resend the series with a fixed title in the cover letter.
v1->v2:
- Break the previous single patch into several patches.
- Fix compilation issues which were reported by krobot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tomer Tayar [Wed, 27 Dec 2017 17:30:07 +0000 (19:30 +0200)]
qed*: Utilize FW 8.33.1.0
Advance the qed* drivers to use firmware 8.33.1.0:
Modify core driver (qed) to utilize the new FW and initialize the device
with it. This is the lion's share of the patch, and includes changes to FW
interface files, device initialization flows, FW interaction flows, and
debug collection flows.
Modify Ethernet driver (qede) to make use of new FW in fastpath.
Modify RoCE/iWARP driver (qedr) to make use of new FW in fastpath.
Modify FCoE driver (qedf) to make use of new FW in fastpath.
Modify iSCSI driver (qedi) to make use of new FW in fastpath.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Yuval Bason <Yuval.Bason@cavium.com> Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com> Signed-off-by: Manish Chopra <Manish.Chopra@cavium.com> Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com> Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com> Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tomer Tayar [Wed, 27 Dec 2017 17:30:06 +0000 (19:30 +0200)]
qed*: HSI renaming for different types of HW
This patch renames defines and structures in the FW HSI files to allow a
distinction between different types of HW.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com> Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com> Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tomer Tayar [Wed, 27 Dec 2017 17:30:05 +0000 (19:30 +0200)]
qed*: Refactoring and rearranging FW API with no functional impact
This patch refactors and reorders the FW API files in preparation of
upgrading the code to support new FW.
- Make use of the BIT macro in appropriate places.
- Whitespace changes to align values and code blocks.
- Comments are updated (spelling mistakes, removed if not clear).
- Group together code blocks which are related or deal with similar
matters.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kristian Evensen [Wed, 27 Dec 2017 17:27:58 +0000 (18:27 +0100)]
inet_diag: Add equal-operator for ports
inet_diag currently provides less/greater than or equal operators for
comparing ports when filtering sockets. An equal comparison can be
performed by combining the two existing operators, or a user can for
example request a port range and then do the final filtering in
userspace. However, these approaches both have drawbacks. Implementing
equal using LE/GE causes the size and complexity of a filter to grow
quickly as the number of ports increase, while it on busy machines would
be great if the kernel only returns information about relevant sockets.
This patch introduces source and destination port equal operators.
INET_DIAG_BC_S_EQ is used to match a source port, INET_DIAG_BC_D_EQ a
destination port, and usage is the same as for the existing port
operators. I.e., the port to match is stored in the no-member of the
next inet_diag_bc_op-struct in the filter.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
please apply some post-christmas leftovers for 4.16.
Two patches to improve IP address management on L3, and two that add
support to auto-config the transport mode on z/VM VNICs.
Note that one patch in the series touches arch/s390 (acked by Martin).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 27 Dec 2017 16:44:31 +0000 (17:44 +0100)]
s390/qeth: support early setup for z/VM NICs
The transport mode that a z/VM NIC is configured in, must match the
hypervisor-internal network which the NIC is coupled to.
To get this right automatically, have qeth issue a diag26c hypervisor call
that provides all sorts of information for a specific VNIC.
With z/VM update VM65918, this also includes the VNIC's required
transport mode.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 27 Dec 2017 16:44:30 +0000 (17:44 +0100)]
s390/diag: add diag26c support for VNIC info
With subcode 0x24, diag26c returns all sorts of VNIC-related information.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Wed, 27 Dec 2017 14:51:38 +0000 (15:51 +0100)]
openvswitch: drop unneeded newline
OVS_NLERR prints a newline at the end of the message string, so the
message string does not need to include a newline explicitly. Done
using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Wed, 27 Dec 2017 14:51:36 +0000 (15:51 +0100)]
net: dccp: drop unneeded newline
DCCP_CRIT prints some other text and then a newline after the message
string, so the message string does not need to include a newline
explicitly. Done using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Wed, 27 Dec 2017 09:05:52 +0000 (17:05 +0800)]
net: sched: fix skb leak in dev_requeue_skb()
When dev_requeue_skb() is called with bulked skb list, only the
first skb of the list will be requeued to qdisc layer, and leak
the others without free them.
TCP is broken due to skb leak since no free skb will be considered
as still in the host queue and never be retransmitted. This happend
when dev_requeue_skb() called from qdisc_restart().
qdisc_restart
|-- dequeue_skb
|-- sch_direct_xmit()
|-- dev_requeue_skb() <-- skb may bluked
Fix dev_requeue_skb() to requeue the full bluked list. Also change
to use __skb_queue_tail() in __dev_requeue_skb() to avoid skb out
of order.
Fixes: a53851e2c321 ("net: sched: explicit locking in gso_cpu fallback") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Wed, 27 Dec 2017 07:42:57 +0000 (13:12 +0530)]
cxgb4: use CLIP with LIP6 on T6 for TCAM filters
On T6, LIP compression is always enabled for IPv6 and uncompressed
IPv6 for LIP is not supported. So, for IPv6 TCAM filters on T6,
add LIP6 to CLIP on filter creation, and release the same on filter
deletion.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com> Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhu Yanjun [Tue, 26 Dec 2017 06:22:50 +0000 (01:22 -0500)]
forcedeth: optimize the rx with likely
In the rx fastpath, the function netdev_alloc_skb rarely fails.
Therefore, a likely() optimization is added to this error check
conditional.
CC: Srinivas Eeda <srinivas.eeda@oracle.com> CC: Joe Jin <joe.jin@oracle.com> CC: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan [Mon, 25 Dec 2017 22:43:04 +0000 (14:43 -0800)]
selftests/net: fix bugs in address and port initialization
Address/port initialization should work correctly regardless
of the order in which command line arguments are supplied,
E.g, cfg_port should be used to connect to the remote host
even if it is processed after -D, src/dst address initialization
should not require that [-4|-6] be specified before
the -S or -D args, receiver should be able to bind to *.<cfg_port>
Achieve this by making sure that the address/port structures
are initialized after all command line options are parsed.
Store cfg_port in host-byte order, and use htons()
to set up the sin_port/sin6_port before bind/connect,
so that the network system calls get the correct values
in network-byte order.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: sched: Fix RED qdisc offload flag
Replacing the RED offload flag (TC_RED_OFFLOADED) with the generic one
(TCQ_F_OFFLOADED) deleted some of the logic behind it. This patchset fixes
this problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nogah Frankel [Mon, 25 Dec 2017 08:51:41 +0000 (10:51 +0200)]
net_sch: red: Fix the new offload indication
Update the offload flag, TCQ_F_OFFLOADED, in each dump call (and ignore
the offloading function return value in relation to this flag).
This is done because a qdisc is being initialized, and therefore offloaded
before being grafted. Since the ability of the driver to offload the qdisc
depends on its location, a qdisc can be offloaded and un-offloaded by graft
calls, that doesn't effect the qdisc itself.
Fixes: 428a68af3a7c ("net: sched: Move to new offload indication in RED" Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Yuval Mintz <yuvalm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jia-Ju Bai [Sun, 24 Dec 2017 03:54:33 +0000 (11:54 +0800)]
sky2: Replace mdelay with msleep in sky2_vpd_wait
sky2_vpd_wait is not called in an interrupt handler nor holding a spinlock.
The function mdelay in it can be replaced with msleep, to reduce busy wait.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Thu, 28 Dec 2017 03:50:25 +0000 (19:50 -0800)]
net: ptr_ring: otherwise safe empty checks can overrun array bounds
When running consumer and/or producer operations and empty checks in
parallel its possible to have the empty check run past the end of the
array. The scenario occurs when an empty check is run while
__ptr_ring_discard_one() is in progress. Specifically after the
consumer_head is incremented but before (consumer_head >= ring_size)
check is made and the consumer head is zeroe'd.
To resolve this, without having to rework how consumer/producer ops
work on the array, simply add an extra dummy slot to the end of the
array. Even if we did a rework to avoid the extra slot it looks
like the normal case checks would suffer some so best to just
allocate an extra pointer.
Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com> Fixes: c5ad119fb6c09 ("net: sched: pfifo_fast use skb_array") Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
include/trace/events/tcp.h is a little bit more tricky. The removal
of in-trace-macro ifdefs in 'net' paralleled with moving
show_tcp_state_name and friends over to include/trace/events/sock.h
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) IPv6 gre tunnels end up with different default features enabled
depending upon whether netlink or ioctls are used to bring them up.
Fix from Alexey Kodanev.
2) Fix read past end of user control message in RDS< from Avinash
Repaka.
3) Missing RCU barrier in mini qdisc code, from Cong Wang.
4) Missing policy put when reusing per-cpu route entries, from Florian
Westphal.
5) Handle nested PCI errors properly in bnx2x driver, from Guilherme G.
Piccoli.
6) Run nested transport mode IPSEC packets via tasklet, from Herbert
Xu.
7) Fix handling poll() for stream sockets in tipc, from Parthasarathy
Bhuvaragan.
8) Fix two stack-out-of-bounds issues in IPSEC, from Steffen Klassert.
9) Another zerocopy ubuf handling fix, from Willem de Bruijn.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
strparser: Call sock_owned_by_user_nocheck
sock: Add sock_owned_by_user_nocheck
skbuff: in skb_copy_ubufs unclone before releasing zerocopy
tipc: fix hanging poll() for stream sockets
sctp: Replace use of sockets_allocated with specified macro.
bnx2x: Improve reliability in case of nested PCI errors
tg3: Enable PHY reset in MTU change path for 5720
tg3: Add workaround to restrict 5762 MRRS to 2048
tg3: Update copyright
net: fec: unmap the xmit buffer that are not transferred by DMA
tipc: fix tipc_mon_delete() oops in tipc_enable_bearer() error path
tipc: error path leak fixes in tipc_enable_bearer()
RDS: Check cmsg_len before dereferencing CMSG_DATA
tcp: Avoid preprocessor directives in tracepoint macro args
tipc: fix memory leak of group member when peer node is lost
net: sched: fix possible null pointer deref in tcf_block_put
tipc: base group replicast ack counter on number of actual receivers
net_sched: fix a missing rcu barrier in mini_qdisc_pair_swap()
net: phy: micrel: ksz9031: reconfigure autoneg after phy autoneg workaround
ip6_gre: fix device features for ioctl setup
...
Linus Torvalds [Fri, 29 Dec 2017 07:16:24 +0000 (23:16 -0800)]
Merge tag 'drm-fixes-for-v4.15-rc6' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"nouveau and i915 regression fixes"
* tag 'drm-fixes-for-v4.15-rc6' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: fix race when adding delayed work items
i915: Reject CCS modifiers for pipe C on Geminilake
drm/i915/gvt: Fix pipe A enable as default for vgpu
Linus Torvalds [Fri, 29 Dec 2017 07:14:47 +0000 (23:14 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One more fix for the runtime PM clk patches. We're calling a runtime
PM API that may schedule from somewhere that we can't do that. We
change to the async version of pm_runtime_put() to fix it"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: use atomic runtime pm api in clk_core_is_enabled
Linus Torvalds [Fri, 29 Dec 2017 07:09:45 +0000 (23:09 -0800)]
Merge tag 'led_fixes_for_4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fix from Jacek Anaszewski:
"A single LED fix for brightness setting when delay_off is 0"
* tag 'led_fixes_for_4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
led: core: Fix brightness setting when setting delay_off=0
Linus Torvalds [Fri, 29 Dec 2017 07:06:01 +0000 (23:06 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"This is the next batch of for-rc patches from RDMA. It includes the
fix for the ipoib regression I mentioned last time, and the result of
a fairly major debugging effort to get iser working reliably on cxgb4
hardware - it turns out the cxgb4 driver was not handling QP error
flushing properly causing iser to fail.
- cxgb4 fix for an iser testing failure as debugged by Steve and
Sagi. The problem was a driver bug in the handling of shutting down
a QP.
- Various vmw_pvrdma fixes for bogus WARN_ON, missed resource free on
error unwind and a use after free bug
- Improper congestion counter values on mlx5 when link aggregation is
enabled
- ipoib lockdep regression introduced in this merge window
- hfi1 regression supporting the device in a VM introduced in a
recent patch
- Typo that breaks future uAPI compatibility in the verbs core
- More SELinux related oops fixing
- Fix an oops during error unwind in mlx5"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/mlx5: Fix mlx5_ib_alloc_mr error flow
IB/core: Verify that QP is security enabled in create and destroy
IB/uverbs: Fix command checking as part of ib_uverbs_ex_modify_qp()
IB/mlx5: Serialize access to the VMA list
IB/hfi: Only read capability registers if the capability exists
IB/ipoib: Fix lockdep issue found on ipoib_ib_dev_heavy_flush
IB/mlx5: Fix congestion counters in LAG mode
RDMA/vmw_pvrdma: Avoid use after free due to QP/CQ/SRQ destroy
RDMA/vmw_pvrdma: Use refcount_dec_and_test to avoid warning
RDMA/vmw_pvrdma: Call ib_umem_release on destroy QP path
iw_cxgb4: when flushing, complete all wrs in a chain
iw_cxgb4: reflect the original WR opcode in drain cqes
iw_cxgb4: Only validate the MSN for successful completions
This series includes updates for mlx5 E-Switch infrastructures,
to be merged into net-next and rdma-next trees.
Mark's patches provide E-Switch refactoring that generalize the mlx5
E-Switch vf representors interfaces and data structures. The serious is
mainly focused on moving ethernet (netdev) specific representors logic out
of E-Switch (eswitch.c) into mlx5e representor module (en_rep.c), which
provides better separation and allows future support for other types of vf
representors (e.g. RDMA).
Gal's patches at the end of this serious, provide a simple syntax fix and
two other patches that handles vport ingress/egress ACL steering name
spaces to be aligned with the Firmware/Hardware specs.
V1->V2:
- Addressed coding style comments in patches #1 and #7
- The series is still based on rc4, as now I see net-next is also @rc4.
V2->V3:
- Fixed compilation warning, reported by Dave.
Please pull and let me know if there's any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-jammy-kernel.git / log