The digital filter related computation are present in the driver
however the programming of the filter within the IP is missing.
The maximum value for the DNF is wrong and should be 15 instead of 16.
It turns out that reasoning for lowering max. supported frequency is
wrong. Scrambling works just fine. Several now fixed bugs prevented
proper functioning, even with rates lower than 340 MHz. Issues were just
more pronounced with higher frequencies.
Fix that by allowing max. supported frequency in HW and fix the comment.
As it turns out, vendor HDMI PHY driver for H6 has a pretty big table
of predefined values for various pixel clocks. However, most of them are
not useful/tested because they come from reference driver code. Vendor
PHY driver is concerned with only few of those, namely 27 MHz, 74.25
MHz, 148.5 MHz, 297 MHz and 594 MHz. These are all frequencies for
standard CEA modes.
Fix sun50i_h6_cur_ctr and sun50i_h6_phy_config with the values only for
aforementioned frequencies.
Table sun50i_h6_mpll_cfg doesn't need to be changed because values are
actually frequency dependent and not so much SoC dependent. See i.MX6
documentation for explanation of those values for similar PHY.
Fixes: c71c9b2fee17 ("drm/sun4i: Add support for Synopsys HDMI PHY") Tested-by: Andre Heider <a.heider@gmail.com> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20210209175900.7092-5-jernej.skrabec@siol.net Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Channel 1 has polarity bits for vsync and hsync signals but driver never
sets them. It turns out that with pre-HDMI2 controllers seemingly there
is no issue if polarity is not set. However, with HDMI2 controllers
(H6) there often comes to de-synchronization due to phase shift. This
causes flickering screen. It's safe to assume that similar issues might
happen also with pre-HDMI2 controllers.
Solve issue with setting vsync and hsync polarity. Note that display
stacks with tcon top have polarity bits actually in tcon0 polarity
register.
arm64 references the start address of .builtin_fw (__start_builtin_fw)
with a pair of R_AARCH64_ADR_PREL_PG_HI21/R_AARCH64_LDST64_ABS_LO12_NC
relocations. The compiler is allowed to emit the
R_AARCH64_LDST64_ABS_LO12_NC relocation because struct builtin_fw in
include/linux/firmware.h is 8-byte aligned.
The R_AARCH64_LDST64_ABS_LO12_NC relocation requires the address to be a
multiple of 8, which may not be the case if .builtin_fw is empty.
Unconditionally align .builtin_fw to fix the linker error. 32-bit
architectures could use ALIGN(4) but that would add unnecessary
complexity, so just use ALIGN(8).
Link: https://lkml.kernel.org/r/20201208054646.2913063-1-maskray@google.com Link: https://github.com/ClangBuiltLinux/linux/issues/1204 Fixes: 5658c76 ("firmware: allow firmware files to be built into kernel image") Signed-off-by: Fangrui Song <maskray@google.com> Reported-by: kernel test robot <lkp@intel.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Tested-by: Douglas Anderson <dianders@chromium.org> Acked-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The queue_id is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this queue_id before using it in hclge_reset_vf_queue().
Fixes: 1a426f8b40fc ("net: hns3: fix the VF queue reset flow error") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
20bf2b378729 ("x86/build: Disable CET instrumentation in the kernel")
disabled CET instrumentation which gets added by default by the Ubuntu
gcc9 and 10 by default, but did that only for 64-bit builds. It would
still fail when building a 32-bit target. So disable CET for all x86
builds.
Fixes: 20bf2b378729 ("x86/build: Disable CET instrumentation in the kernel") Reported-by: AC <achirvasub@gmail.com> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Josh Poimboeuf <jpoimboe@redhat.com> Tested-by: AC <achirvasub@gmail.com> Link: https://lkml.kernel.org/r/YCCIgMHkzh/xT4ex@arch-chirva.localdomain Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Normally we clear the failover_pending flag when processing the reset.
But if we are unable to schedule a failover reset we must clear the
flag ourselves. We could fail to schedule the reset if we are in PROBING
state (eg: when booting via kexec) or because we could not allocate memory.
Thanks to Cris Forno for helping isolate the problem and for testing.
When disable CBS, mode_to_use parameter is not updated even the operation
mode of Tx Queue is changed to Data Centre Bridging (DCB). Therefore,
when tc_setup_cbs() function is called to re-enable CBS, the operation
mode of Tx Queue remains at DCB, which causing CBS fails to work.
This patch updates the value of mode_to_use parameter to MTL_QUEUE_DCB
after operation mode of Tx Queue is changed to DCB in stmmac_dma_qmode()
callback function.
Fixes: 1f705bc61aee ("net: stmmac: Add support for CBS QDISC") Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com> Signed-off-by: Song, Yoong Siang <yoong.siang.song@intel.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Link: https://lore.kernel.org/r/1612447396-20351-1-git-send-email-yoong.siang.song@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
PACKET_TX_TIMESTAMP is defined in if_packet.h but it is not included in
test. Include it instead of <netpacket/packet.h> otherwise the error of
redefinition arrives.
Also fix the compiler warning about ambiguous control flow by adding
explicit braces.
Fixes: 8fe2f761cae9 ("net-timestamp: expand documentation") Suggested-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com> Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru> Acked-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/1612461034-24524-1-git-send-email-vfedorenko@novek.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Michael tried to enable Advanced Error Reporting through the ENETC's
Root Complex Event Collector, and the system started spitting out single
bit correctable ECC errors coming from the ENETC interfaces:
Further investigating the port correctable memory error detect register
(PCMEDR) shows that these AER errors have an associated SOURCE_ID of 6
(RFS/RSS):
Discussion with the hardware design engineers reveals that on LS1028A,
the hardware does not do initialization of that RFS/RSS memory, and that
software should clear/initialize the entire table before starting to
operate. That comes as a bit of a surprise, since the driver does not do
initialization of the RFS memory. Also, the initialization of the
Receive Side Scaling is done only partially.
Even though the entire ENETC IP has a single shared flow steering
memory, the flow steering service should returns matches only for TCAM
entries that are within the range of the Station Interface that is doing
the search. Therefore, it should be sufficient for a Station Interface
to initialize all of its own entries in order to avoid any ECC errors,
and only the Station Interfaces in use should need initialization.
There are Physical Station Interfaces associated with PCIe PFs and
Virtual Station Interfaces associated with PCIe VFs. We let the PF
driver initialize the entire port's memory, which includes the RFS
entries which are going to be used by the VF.
Reported-by: Michael Walle <michael@walle.cc> Fixes: d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Michael Walle <michael@walle.cc> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Link: https://lore.kernel.org/r/20210204134511.2640309-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Since commit 23025393dbeb3b8b3 ("xen/netback: use lateeoi irq binding")
xenvif_rx_ring_slots_available() is no longer called only from the rx
queue kernel thread, so it needs to access the rx queue with the
associated queue held.
Reported-by: Igor Druzhinin <igor.druzhinin@citrix.com> Fixes: 23025393dbeb3b8b3 ("xen/netback: use lateeoi irq binding") Signed-off-by: Juergen Gross <jgross@suse.com> Acked-by: Wei Liu <wl@xen.org> Link: https://lore.kernel.org/r/20210202070938.7863-1-jgross@suse.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When updating the tcp or udp header checksum on port nat the function
inet_proto_csum_replace2 with the last parameter pseudohdr as true.
This leads to an error in the case that GRO is used and packets are
split up in GSO. The tcp or udp checksum of all packets is incorrect.
The error is probably masked due to the fact the most network driver
implement tcp/udp checksum offloading. It also only happens when GRO is
applied and not on single packets.
The error is most visible when using a pppoe connection which is not
triggering the tcp/udp checksum offload.
Fixes: ac2a66665e23 ("netfilter: add generic flow table infrastructure") Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Although hooks are released via call_rcu(), chain and rule objects are
immediately released while packets are still walking over these bits.
This patch adds the .pre_exit callback which is invoked before
synchronize_rcu() in the netns framework to stay safe.
Remove a comment which is not valid anymore since the core does not use
synchronize_net() anymore since 8c873e219970 ("netfilter: core: free
hooks with call_rcu").
Suggested-by: Florian Westphal <fw@strlen.de> Fixes: df05ef874b28 ("netfilter: nf_tables: release objects on netns destruction") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When both --reap and --update flag are specified, there's a code
path at which the entry to be updated is reaped beforehand,
which then leads to kernel crash. Reap only entries which won't be
updated.
Fixes kernel bugzilla #207773.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=207773 Reported-by: Reindl Harald <h.reindl@thelounge.net> Fixes: 0079c5aee348 ("netfilter: xt_recent: add an entry reaper") Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
On 32-bit architecture, roundup_pow_of_two() can return 0 when the argument
has upper most bit set due to resulting 1UL << 32. Add a check for this case.
Commit 0a038c1c29a7 ("drm/vc4: Move LBM creation out of
vc4_plane_mode_set()") changed the LBM allocation logic from first
allocating the LBM memory for the plane to running mode_set,
adding a gap in the LBM, and then running the dlist allocation filling
that gap.
The gap was introduced by incrementing the dlist array index, but was
never checking whether or not we were over the array length, leading
eventually to memory corruptions if we ever crossed this limit.
vc4_dlist_write had that logic though, and was reallocating a larger
dlist array when reaching the end of the buffer. Let's share the logic
between both functions.
Cc: Boris Brezillon <boris.brezillon@collabora.com> Cc: Eric Anholt <eric@anholt.net> Fixes: 0a038c1c29a7 ("drm/vc4: Move LBM creation out of vc4_plane_mode_set()") Signed-off-by: Maxime Ripard <maxime@cerno.tech> Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210129160647.128373-1-maxime@cerno.tech Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Fix a memory leak in mt76_add_fragment routine returning the buffer
to the page_frag_cache when we receive a new fragment and the
skb_shared_info frag array is full.
Fixes: b102f0c522cf6 ("mt76: fix array overflow on receiving too many fragments for a packet") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Acked-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/4f9dd73407da88b2a552517ce8db242d86bf4d5c.1611616130.git.lorenzo@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When building with KASAN and LKDTM, clang may implictly generate an
asan.module_ctor function in the LKDTM rodata object. The Makefile moves
the lkdtm_rodata_do_nothing() function into .rodata by renaming the
file's .text section to .rodata, and consequently also moves the ctor
function into .rodata, leading to a boot time crash (splat below) when
the ctor is invoked by do_ctors().
Let's prevent this by marking the function as noinstr rather than
notrace, and renaming the file's .noinstr.text to .rodata. Marking the
function as noinstr will prevent tracing and kprobes, and will inhibit
any undesireable compiler instrumentation.
The ctor function (if any) will be placed in .text and will work
correctly.
Some code pathes, especially the low level entry code, must be protected
against instrumentation for various reasons:
- Low level entry code can be a fragile beast, especially on x86.
- With NO_HZ_FULL RCU state needs to be established before using it.
Having a dedicated section for such code allows to validate with tooling
that no unsafe functions are invoked.
Add the .noinstr.text section and the noinstr attribute to mark
functions. noinstr implies notrace. Kprobes will gain a section check
later.
Provide also a set of markers: instrumentation_begin()/end()
These are used to mark code inside a noinstr function which calls
into regular instrumentable text section as safe.
The instrumentation markers are only active when CONFIG_DEBUG_ENTRY is
enabled as the end marker emits a NOP to prevent the compiler from merging
the annotation points. This means the objtool verification requires a
kernel compiled with this option.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com> Acked-by: Peter Zijlstra <peterz@infradead.org> Link: https://lkml.kernel.org/r/20200505134100.075416272@linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Giancarlo Ferrari reports the following oops while trying to use kexec:
Unable to handle kernel paging request at virtual address 80112f38
pgd = fd7ef03e
[80112f38] *pgd=0001141e(bad)
Internal error: Oops: 80d [#1] PREEMPT SMP ARM
...
This is caused by machine_kexec() trying to set the kernel text to be
read/write, so it can poke values into the relocation code before
copying it - and an interrupt occuring which changes the page tables.
The subsequent writes then hit read-only sections that trigger a
data abort resulting in the above oops.
Fix this by copying the relocation code, and then writing the variables
into the destination, thereby avoiding the need to make the kernel text
read/write.
Reported-by: Giancarlo Ferrari <giancarlo.ferrari89@gmail.com> Tested-by: Giancarlo Ferrari <giancarlo.ferrari89@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Ensure that the signal page contains our poison instruction to increase
the protection against ROP attacks and also contains well defined
contents.
Acked-by: Will Deacon <will@kernel.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The lpc32xx clock driver is not able to actually change the PLL rate as
this would require reparenting ARM_CLK, DDRAM_CLK, PERIPH_CLK to SYSCLK,
then stop the PLL, update the register, restart the PLL and wait for the
PLL to lock and finally reparent ARM_CLK, DDRAM_CLK, PERIPH_CLK to HCLK
PLL.
Currently, the HCLK driver simply updates the registers but this has no
real effect and all the clock rate calculation end up being wrong. This is
especially annoying for the peripheral (e.g. UARTs, I2C, SPI).
bfq.limit_depth passes word_depths[] as shallow_depth down to sbitmap core
sbitmap_get_shallow, which uses just the number to limit the scan depth of
each bitmap word, formula:
scan_percentage_for_each_word = shallow_depth / (1 << sbimap->shift) * 100%
That means the comments's percentiles 50%, 75%, 18%, 37% of bfq are correct.
But after commit patch 'bfq: Fix computation of shallow depth', we use
sbitmap.depth instead, as a example in following case:
sbitmap.depth = 256, map_nr = 4, shift = 6; sbitmap_word.depth = 64.
The resulsts of computed bfqd->word_depths[] are {128, 192, 48, 96}, and
three of the numbers exceed core dirver's 'sbitmap_word.depth=64' limit
nothing.
Signed-off-by: Lin Feng <linf@wangsu.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
virt_addr_valid macro checks that a virtual address is valid, ie that
the address belongs to the linear mapping and that the corresponding
physical page exists.
Add the missing check that ensures the virtual address belongs to the
linear mapping, otherwise __virt_to_phys, when compiled with
CONFIG_DEBUG_VIRTUAL enabled, raises a WARN that is interpreted as a
kernel bug by syzbot.
[why]
An old dc_sink state is causing a memory leak because it is missing a
dc_sink_release before a new dc_sink is assigned back to
aconnector->dc_sink.
[how]
Decrement the dc_sink refcount before reassigning it to a new dc_sink.
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com> Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
[why]
drm_atomic_commit was changed so that the caller must free their
drm_atomic_state reference on successes.
[how]
Add drm_atomic_commit_put after drm_atomic_commit call in
dm_force_atomic_commit.
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com> Reviewed-by: Roman Li <Roman.Li@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
[why]
prev_sink is not used anywhere else in the function and the reference to
it from dc_link is replaced with a new dc_sink.
[how]
Change dc_sink_retain(prev_sink) to dc_sink_release(prev_sink).
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When inode has no listxattr op of its own (e.g. squashfs) vfs_listxattr
calls the LSM inode_listsecurity hooks to list the xattrs that LSMs will
intercept in inode_getxattr hooks.
When selinux LSM is installed but not initialized, it will list the
security.selinux xattr in inode_listsecurity, but will not intercept it
in inode_getxattr. This results in -ENODATA for a getxattr call for an
xattr returned by listxattr.
This situation was manifested as overlayfs failure to copy up lower
files from squashfs when selinux is built-in but not initialized,
because ovl_copy_xattr() iterates the lower inode xattrs by
vfs_listxattr() and vfs_getxattr().
ovl_copy_xattr() skips copy up of security labels that are indentified by
inode_copy_up_xattr LSM hooks, but it does that after vfs_getxattr().
Since we are not going to copy them, skip vfs_getxattr() of the security
labels.
Reported-by: Michael Labriola <michael.d.labriola@gmail.com> Tested-by: Michael Labriola <michael.d.labriola@gmail.com> Link: https://lore.kernel.org/linux-unionfs/2nv9d47zt7.fsf@aldarion.sourceruckus.org/ Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If a capability is stored on disk in v2 format cap_inode_getsecurity() will
currently return in v2 format unconditionally.
This is wrong: v2 cap should be equivalent to a v3 cap with zero rootid,
and so the same conversions performed on it.
If the rootid cannot be mapped, v3 is returned unconverted. Fix this so
that both v2 and v3 return -EOVERFLOW if the rootid (or the owner of the fs
user namespace in case of v2) cannot be mapped into the current user
namespace.
The vfs_getxattr() in ovl_xattr_set() is used to check whether an xattr
exist on a lower layer file that is to be removed. If the xattr does not
exist, then no need to copy up the file.
This call of vfs_getxattr() wasn't wrapped in credential override, and this
is probably okay. But for consitency wrap this instance as well.
Recently userspace has started making more use of SW_TABLET_MODE
(when an input-dev reports this).
Specifically recent GNOME3 versions will:
1. When SW_TABLET_MODE is reported and is reporting 0:
1.1 Disable accelerometer-based screen auto-rotation
1.2 Disable automatically showing the on-screen keyboard when a
text-input field is focussed
2. When SW_TABLET_MODE is reported and is reporting 1:
2.1 Ignore input-events from the builtin keyboard and touchpad
(this is for 360° hinges style 2-in-1s where the keyboard and
touchpads are accessible on the back of the tablet when folded
into tablet-mode)
This means that claiming to support SW_TABLET_MODE when it does not
actually work / reports correct values has bad side-effects.
The check in the hp-wmi code which is used to decide if the input-dev
should claim SW_TABLET_MODE support, only checks if the
HPWMI_HARDWARE_QUERY is supported. It does *not* check if the hardware
actually is capable of reporting SW_TABLET_MODE.
This leads to the hp-wmi input-dev claiming SW_TABLET_MODE support,
while in reality it will always report 0 as SW_TABLET_MODE value.
This has been seen on a "HP ENVY x360 Convertible 15-cp0xxx" and
this likely is the case on a whole lot of other HP models.
This problem causes both auto-rotation and on-screen keyboard
support to not work on affected x360 models.
There is no easy fix for this, but since userspace expects
SW_TABLET_MODE reporting to be reliable when advertised it is
better to not claim/report SW_TABLET_MODE support at all, then
to claim to support it while it does not work.
To avoid the mentioned problems, add a new enable_tablet_mode_sw
module-parameter which defaults to false.
Note I've made this an int using the standard -1=auto, 0=off, 1=on
triplett, with the hope that in the future we can come up with a
better way to detect SW_TABLET_MODE support. ATM the default
auto option just does the same as off.
We get suspcious RCU usage splats with cpuidle in several places in
omap_enter_idle_coupled() with the kernel debug options enabled:
RCU used illegally from extended quiescent state!
...
(_raw_spin_lock_irqsave)
(omap_enter_idle_coupled+0x17c/0x2d8)
(omap_enter_idle_coupled)
(cpuidle_enter_state)
(cpuidle_enter_state_coupled)
(cpuidle_enter)
Let's use RCU_NONIDLE to suppress these splats. Things got changed around
with commit 1098582a0f6c ("sched,idle,rcu: Push rcu_idle deeper into the
idle path") that started triggering these warnings.
For the tick_broadcast related calls, ideally we'd just switch over to
using CPUIDLE_FLAG_TIMER_STOP for omap_enter_idle_coupled() to have the
generic cpuidle code handle the tick_broadcast related calls for us and
then just drop the tick_broadcast calls here.
But we're currently missing the call in the common cpuidle code for
tick_broadcast_enable() that CPU1 hotplug needs as described in earlier
commit 50d6b3cf9403 ("ARM: OMAP2+: fix lack of timer interrupts on CPU1
after hotplug").
Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Paul E. McKenney <paulmck@kernel.org> Cc: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The GCC_LPASS_Q6_AXI_CLK and GCC_LPASS_SWAY_CLK clocks may not be
touched on a typical UEFI based SDM845 device, but when the kernel is
built with CONFIG_SDM_LPASSCC_845 this happens, unless they are marked
as protected-clocks in the DT.
This was done for the MTP and the Pocophone, but not for DB845c and the
Lenovo Yoga C630 - causing these to fail to boot if the LPASS clock
controller is enabled (which it typically isn't).
It recently became apparent that the lack of a 'device_type = "pci"'
in the PCIe root complex node for rk3399 is a violation of the PCI
binding, as documented in IEEE Std 1275-1994. Changes to the kernel's
parsing of the DT made such violation fatal, as drivers cannot
probe the controller anymore.
Add the missing property makes the PCIe node compliant. While we
are at it, drop the pointless linux,pci-domain property, which only
makes sense when there are multiple host bridges.
Fix NULL pointer dereference when adding new psi monitor to the root
cgroup. PSI files for root cgroup was introduced in df5ba5be742 by using
system wide psi struct when reading, but file write/monitor was not
properly fixed. Since the PSI config for the root cgroup isn't
initialized, the current implementation tries to lock a NULL ptr,
resulting in a crash.
Can be triggered by running this as root:
$ tee /sys/fs/cgroup/cpu.pressure <<< "some 10000 1000000"
After Commit 3499ba8198cad ("xen: Fix event channel callback via
INTX/GSI"), xenbus_probe() will be called too early on Arm. This will
recent to a guest hang during boot.
If the hang wasn't there, we would have ended up to call
xenbus_probe() twice (the second time is in xenbus_probe_initcall()).
We don't need to initialize xenbus_probe() early for Arm guest.
Therefore, the call in xen_guest_init() is now removed.
After this change, there is no more external caller for xenbus_probe().
So the function is turned to a static one. Interestingly there were two
prototypes for it.
Cc: stable@vger.kernel.org Fixes: 3499ba8198cad ("xen: Fix event channel callback via INTX/GSI") Reported-by: Ian Jackson <iwj@xenproject.org> Signed-off-by: Julien Grall <jgrall@amazon.com> Reviewed-by: David Woodhouse <dwmw@amazon.co.uk> Reviewed-by: Stefano Stabellini <sstabellini@kernel.org> Link: https://lore.kernel.org/r/20210210170654.5377-1-julien@xen.org Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When filters are used by trace events, a page is allocated on each CPU and
used to copy the trace event fields to this page before writing to the ring
buffer. The reason to use the filter and not write directly into the ring
buffer is because a filter may discard the event and there's more overhead
on discarding from the ring buffer than the extra copy.
The problem here is that there is no check against the size being allocated
when using this page. If an event asks for more than a page size while being
filtered, it will get only a page, leading to the caller writing more that
what was allocated.
Check the length of the request, and if it is more than PAGE_SIZE minus the
header default back to allocating from the ring buffer directly. The ring
buffer may reject the event if its too big anyway, but it wont overflow.
Link: https://lore.kernel.org/ath10k/1612839593-2308-1-git-send-email-wgong@codeaurora.org/ Cc: stable@vger.kernel.org Fixes: 0fc1b09ff1ff4 ("tracing: Use temp buffer when filtering events") Reported-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The file /sys/kernel/tracing/events/enable is used to enable all events by
echoing in "1", or disabling all events when echoing in "0". To know if all
events are enabled, disabled, or some are enabled but not all of them,
cating the file should show either "1" (all enabled), "0" (all disabled), or
"X" (some enabled but not all of them). This works the same as the "enable"
files in the individule system directories (like tracing/events/sched/enable).
But when all events are enabled, the top level "enable" file shows "X". The
reason is that its checking the "ftrace" events, which are special events
that only exist for their format files. These include the format for the
function tracer events, that are enabled when the function tracer is
enabled, but not by the "enable" file. The check includes these events,
which will always be disabled, and even though all true events are enabled,
the top level "enable" file will show "X" instead of "1".
To fix this, have the check test the event's flags to see if it has the
"IGNORE_ENABLE" flag set, and if so, not test it.
Cc: stable@vger.kernel.org Fixes: 553552ce1796c ("tracing: Combine event filter_active and enable into single flags field") Reported-by: "Yordan Karadzhov (VMware)" <y.karadz@gmail.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Fixes the following warnings which results in interrupts disabled on
port B/F:
gpio gpiochip1: (B): detected irqchip that is shared with multiple gpiochips: please fix the driver.
gpio gpiochip5: (F): detected irqchip that is shared with multiple gpiochips: please fix the driver.
- added separate irqchip for each interrupt capable gpiochip
- provided unique names for each irqchip
Two index spaces and ep93xx_gpio_port are confusing.
Instead add a separate struct to store necessary data and remove
ep93xx_gpio_port.
- add struct to store IRQ related data for each IRQ capable chip
- replace offset array with defined offsets
- add IRQ registers offset for each IRQ capable chip into
ep93xx_gpio_banks
------------[ cut here ]------------
kernel BUG at drivers/gpio/gpio-ep93xx.c:64!
---[ end trace 3f6544e133e9f5ae ]---
Fixes: fd935fc421e74 ("gpio: ep93xx: Do not pingpong irq numbers") Cc: <stable@vger.kernel.org> Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com> Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com> Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Sysbot has reported a warning where a kmalloc() attempt exceeds the
maximum limit. This has been identified as corruption of the xattr_ids
count when reading the xattr id lookup table.
This patch adds a number of additional sanity checks to detect this
corruption and others.
1. It checks for a corrupted xattr index read from the inode. This could
be because the metadata block is uncompressed, or because the
"compression" bit has been corrupted (turning a compressed block
into an uncompressed block). This would cause an out of bounds read.
2. It checks against corruption of the xattr_ids count. This can either
lead to the above kmalloc failure, or a smaller than expected
table to be read.
3. It checks the contents of the index table for corruption.
Sysbot has reported an "slab-out-of-bounds read" error which has been
identified as being caused by a corrupted "ino_num" value read from the
inode. This could be because the metadata block is uncompressed, or
because the "compression" bit has been corrupted (turning a compressed
block into an uncompressed block).
This patch adds additional sanity checks to detect this, and the
following corruption.
1. It checks against corruption of the inodes count. This can either
lead to a larger table to be read, or a smaller than expected
table to be read.
In the case of a too large inodes count, this would often have been
trapped by the existing sanity checks, but this patch introduces
a more exact check, which can identify too small values.
2. It checks the contents of the index table for corruption.
Sysbot has reported a number of "slab-out-of-bounds reads" and
"use-after-free read" errors which has been identified as being caused
by a corrupted index value read from the inode. This could be because
the metadata block is uncompressed, or because the "compression" bit has
been corrupted (turning a compressed block into an uncompressed block).
This patch adds additional sanity checks to detect this, and the
following corruption.
1. It checks against corruption of the ids count. This can either
lead to a larger table to be read, or a smaller than expected
table to be read.
In the case of a too large ids count, this would often have been
trapped by the existing sanity checks, but this patch introduces
a more exact check, which can identify too small values.
2. It checks the contents of the index table for corruption.
Grab kvm->lock before pinning memory when registering an encrypted
region; sev_pin_memory() relies on kvm->lock being held to ensure
correctness when checking and updating the number of pinned pages.
Add a lockdep assertion to help prevent future regressions.
Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Joerg Roedel <joro@8bytes.org> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: Brijesh Singh <brijesh.singh@amd.com> Cc: Sean Christopherson <seanjc@google.com> Cc: x86@kernel.org Cc: kvm@vger.kernel.org Cc: stable@vger.kernel.org Cc: linux-kernel@vger.kernel.org Fixes: 1e80fdc09d12 ("KVM: SVM: Pin guest memory when SEV is active") Signed-off-by: Peter Gonda <pgonda@google.com>
V2
- Fix up patch description
- Correct file paths svm.c -> sev.c
- Add unlock of kvm->lock on sev_pin_memory error
With commit eaa7995c529b54 (regulator: core: avoid
regulator_resolve_supply() race condition) we started holding the rdev
lock while resolving supplies, an operation that requires holding the
regulator_list_mutex. This results in lockdep warnings since in other
places we take the list mutex then the mutex on an individual rdev.
Since the goal is to make sure that we don't call set_supply() twice
rather than a concern about the cost of resolution pull the rdev lock
and check for duplicate resolution down to immediately before we do the
set_supply() and drop it again once the allocation is done.
Fixes: eaa7995c529b54 (regulator: core: avoid regulator_resolve_supply() race condition) Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20210122132042.10306-1-broonie@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
On !PREEMPT kernel, we can get below softlockup when doing stress
testing with creating and destroying block cgroup repeatly. The
reason is it may take a long time to acquire the queue's lock in
the loop of blkcg_destroy_blkgs(), or the system can accumulate a
huge number of blkgs in pathological cases. We can add a need_resched()
check on each loop and release locks and do cond_resched() if true
to avoid this issue, since the blkcg_destroy_blkgs() is not called
from atomic contexts.
Some i2c device driver indirectly uses I2C driver when it is now
being suspended. The i2c devices driver is suspended during the
NOIRQ phase and this cannot be changed due to other dependencies.
Therefore, we also need to move the suspend handling for the I2C
controller driver to the NOIRQ phase as well.
Signed-off-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When handling an auth_gss downcall, it's possible to get 0-length
opaque object for the acceptor. In the case of a 0-length XDR
object, make sure simple_get_netobj() fills in dest->data = NULL,
and does not continue to kmemdup() which will set
dest->data = ZERO_SIZE_PTR for the acceptor.
The trace event code can handle NULL but not ZERO_SIZE_PTR for a
string, and so without this patch the rpcgss_context trace event
will crash the kernel as follows:
Remove duplicated helper functions to parse opaque XDR objects
and place inside new file net/sunrpc/auth_gss/auth_gss_internal.h.
In the new file carry the license and copyright from the source file
net/sunrpc/auth_gss/auth_gss.c. Finally, update the comment inside
include/linux/sunrpc/xdr.h since lockd is not the only user of
struct xdr_netobj.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If we get into a problem severe enough to attempt a reprobe,
we schedule a worker to do that. However, if the problem gets
more severe and the device is actually destroyed before this
worker has a chance to run, we use a free device. Bump up the
reference count of the device until the worker runs to avoid
this situation.
Having sta_id not set for aux_sta and snif_sta can potentially lead to a
hard to debug issue in case remove station is called without an add. In
this case sta_id 0, an unrelated regular station, will be removed.
In fact, we do have a FW assert that occures rarely and from the debug
data analysis it looks like sta_id 0 is removed by mistake, though it's
hard to pinpoint the exact flow. The WARN_ON in this patch should help
to find it.
In the new CSA flow, we remain associated during CSA, but
still do a unbind-bind to the vif. However, sending the power
command right after when vif is unbound but still associated
causes FW to assert (0x3400) since it cannot tell the LMAC id.
Just skip this command, we will send it again in a bit, when
assigning the new context.
If the server returns a new stateid that does not match the one in our
cache, then try to return the one we hold instead of just invalidating
it on the client side. This ensures that both client and server will
agree that the stateid is invalid.
Upon receiving CSA with 160MHz extended NSS BW from associated AP,
STA should set the HT operation_mode based on new_center_freq_seg1
because it is later used as ccfs2 in ieee80211_chandef_vht_oper().
Signed-off-by: Aviad Brikman <aviad.brikman@celeno.com> Signed-off-by: Shay Bar <shay.bar@celeno.com> Link: https://lore.kernel.org/r/20201222064714.24888-1-shay.bar@celeno.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The final step in regulator_register() is to call
regulator_resolve_supply() for each registered regulator
(including the one in the process of being registered). The
regulator_resolve_supply() function first checks if rdev->supply
is NULL, then it performs various steps to try to find the supply.
If successful, rdev->supply is set inside of set_supply().
This procedure can encounter a race condition if two concurrent
tasks call regulator_register() near to each other on separate CPUs
and one of the regulators has rdev->supply_name specified. There
is currently nothing guaranteeing atomicity between the rdev->supply
check and set steps. Thus, both tasks can observe rdev->supply==NULL
in their regulator_resolve_supply() calls. This then results in
both creating a struct regulator for the supply. One ends up
actually stored in rdev->supply and the other is lost (though still
present in the supply's consumer_list).
Here is a kernel log snippet showing the issue:
[ 12.421768] gpu_cc_gx_gdsc: supplied by pm8350_s5_level
[ 12.425854] gpu_cc_gx_gdsc: supplied by pm8350_s5_level
[ 12.429064] debugfs: Directory 'regulator.4-SUPPLY' with parent
'17a00000.rsc:rpmh-regulator-gfxlvl-pm8350_s5_level'
already present!
Avoid this race condition by holding the rdev->mutex lock inside
of regulator_resolve_supply() while checking and setting
rdev->supply.
Signed-off-by: David Collins <collinsd@codeaurora.org> Link: https://lore.kernel.org/r/1610068562-4410-1-git-send-email-collinsd@codeaurora.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
xfrm_probe_algs() probes kernel crypto modules and changes the
availability of struct xfrm_algo_desc. But there is a small window
where ealg->available and aalg->available get changed between
count_ah_combs()/count_esp_combs() and dump_ah_combs()/dump_esp_combs(),
in this case we may allocate a smaller skb but later put a larger
amount of data and trigger the panic in skb_put().
Fix this by relaxing the checks when counting the size, that is,
skipping the test of ->available. We may waste some memory for a few
of sizeof(struct sadb_comb), but it is still much better than a panic.
Reported-by: syzbot+b2bf2652983d23734c5c@syzkaller.appspotmail.com Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Fix kprobe_on_func_entry() returns error code instead of false so that
register_kretprobe() can return an appropriate error code.
append_trace_kprobe() expects the kprobe registration returns -ENOENT
when the target symbol is not found, and it checks whether the target
module is unloaded or not. If the target module doesn't exist, it
defers to probe the target symbol until the module is loaded.
However, since register_kretprobe() returns -EINVAL instead of -ENOENT
in that case, it always fail on putting the kretprobe event on unloaded
modules. e.g.
Kprobe event:
/sys/kernel/debug/tracing # echo p xfs:xfs_end_io >> kprobe_events
[ 16.515574] trace_kprobe: This probe might be able to register after target module is loaded. Continue.
To fix this bug, change kprobe_on_func_entry() to detect symbol lookup
failure and return -ENOENT in that case. Otherwise it returns -EINVAL
or 0 (succeeded, given address is on the entry).
Link: https://lkml.kernel.org/r/161176187132.1067016.8118042342894378981.stgit@devnote2 Cc: stable@vger.kernel.org Fixes: 59158ec4aef7 ("tracing/kprobes: Check the probe on unloaded module correctly") Reported-by: Jianlin Lv <Jianlin.Lv@arm.com> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Stefan Bader [Fri, 26 Feb 2021 09:20:04 +0000 (10:20 +0100)]
UBUNTU: [Config] Fix up trusted keys annotation for i386
BugLink: https://bugs.launchpad.net/bugs/1898716
When adding the annotations for CONFIG_SYSTEM_TRUSTED_KEYS the i386
string accidentally missed the '.pem' extension. This does not matter
for Focal itself and most derivatives. Just bionic:linux-hwe-5.4 will
fail to build that way. Fixing the annotation in Focal so future updates
will work correctly.
Ignore: yes Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Guilherme G. Piccoli <gpiccoli@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1916290
In LP: #1872863 we started to build and ship the bochs-drm.ko driver
again, however this config wasn't enforced and because of that
derivatives didn't inherit.
Enforce CONFIG_DRM_BOCHS=m and let the derivatives update their
configuration to include it or not.
Signed-off-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Acked-by: Guilherme Piccoli <gpiccoli@canonical.com>
[smb: dropped BugLink to related bug] Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Michael Ellerman [Wed, 24 Feb 2021 07:14:23 +0000 (15:14 +0800)]
selftests/eeh: Skip ahci adapters
BugLink: https://bugs.launchpad.net/bugs/1916468
The ahci driver doesn't support error recovery, and if your root
filesystem is attached to it the eeh-basic.sh test will likely kill
your machine.
So skip any device we see using the ahci driver.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200326061144.2006522-1-mpe@ellerman.id.au
(cherry picked from commit bbe9064f30f06e7791d04f9f61a842226a6a44fe) Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Guilherme G. Piccoli <gpiccoli@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Older ATF does not provide SMC call for USB 3.0 phy power on functionality
and therefore initialization of xhci-hcd is failing when older version of
ATF is used. In this case phy_power_on() function returns -EOPNOTSUPP.
[ 3.108467] mvebu-a3700-comphy d0018300.phy: unsupported SMC call, try updating your firmware
[ 3.117250] phy phy-d0018300.phy.0: phy poweron failed --> -95
[ 3.123465] xhci-hcd: probe of d0058000.usb failed with error -95
This patch introduces a new plat_setup callback for xhci platform drivers
which is called prior calling usb_add_hcd() function. This function at its
beginning skips PHY init if hcd->skip_phy_initialization is set.
Current init_quirk callback for xhci platform drivers is called from
xhci_plat_setup() function which is called after chip reset completes.
It happens in the middle of the usb_add_hcd() function and therefore this
callback cannot be used for setting if PHY init should be skipped or not.
For Armada 3720 this patch introduce a new xhci_mvebu_a3700_plat_setup()
function configured as a xhci platform plat_setup callback. This new
function calls phy_power_on() and in case it returns -EOPNOTSUPP then
XHCI_SKIP_PHY_INIT quirk is set to instruct xhci-plat to skip PHY
initialization.
This patch fixes above failure by ignoring 'not supported' error in
xhci-hcd driver. In this case it is expected that phy is already power on.
It fixes initialization of xhci-hcd on Espressobin boards where is older
Marvell's Arm Trusted Firmware without SMC call for USB 3.0 phy power.
This is regression introduced in commit bd3d25b07342 ("arm64: dts: marvell:
armada-37xx: link USB hosts with their PHYs") where USB 3.0 phy was defined
and therefore xhci-hcd on Espressobin with older ATF started failing.
Fixes: bd3d25b07342 ("arm64: dts: marvell: armada-37xx: link USB hosts with their PHYs") Cc: <stable@vger.kernel.org> # 5.1+: ea17a0f153af: phy: marvell: comphy: Convert internal SMCC firmware return codes to errno Cc: <stable@vger.kernel.org> # 5.1+: f768e718911e: usb: host: xhci-plat: add priv quirk for skip PHY initialization Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> # On R-Car Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> # xhci-plat Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Pali Rohár <pali@kernel.org> Link: https://lore.kernel.org/r/20210201150803.7305-1-pali@kernel.org
[pali: Backported to 5.4 by replacing of_phy_put() with phy_put()] Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit e5f0e8f8e456 ("net: sched: introduce and use qdisc tree flush/purge helpers")
introduced qdisc tree flush/purge helpers, but erroneously used flush helper
instead of purge helper in qdisc_replace function.
This issue was found in our CI, that tests various qdisc setups by configuring
qdisc and sending data through it. Call of invalid helper sporadically leads
to corruption of vt_tree/cf_tree of hfsc_class that causes kernel oops:
Having multiple destination ports for a unicast address does not make
sense.
Make port_db_load_purge override existent unicast portvec instead of
adding a new port bit.
Fixes: 884729399260 ("net: dsa: mv88e6xxx: handle multiple ports in ATU") Signed-off-by: DENG Qingfang <dqfext@gmail.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Link: https://lore.kernel.org/r/20210130134334.10243-1-dqfext@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
dev->hard_header_len for tunnel interface is set only when header_ops
are set too and already contains full overhead of any tunnel encapsulation.
That's why there is not need to use this overhead twice in mtu calc.
Fixes: fdafed459998 ("ip_gre: set dev->hard_header_len and dev->needed_headroom properly") Reported-by: Slava Bacherikov <mail@slava.cc> Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru> Link: https://lore.kernel.org/r/1611959267-20536-1-git-send-email-vfedorenko@novek.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Following race condition was detected:
<CPU A, t0> - neigh_flush_dev() is under execution and calls
neigh_mark_dead(n) marking the neighbour entry 'n' as dead.
<CPU B, t1> - Executing: __netif_receive_skb() ->
__netif_receive_skb_core() -> arp_rcv() -> arp_process().arp_process()
calls __neigh_lookup() which takes a reference on neighbour entry 'n'.
<CPU A, t2> - Moves further along neigh_flush_dev() and calls
neigh_cleanup_and_release(n), but since reference count increased in t2,
'n' couldn't be destroyed.
<CPU B, t3> - Moves further along, arp_process() and calls
neigh_update()-> __neigh_update() -> neigh_update_gc_list(), which adds
the neighbour entry back in gc_list(neigh_mark_dead(), removed it
earlier in t0 from gc_list)
This leads to 'n' still being part of gc_list, but the actual
neighbour structure has been freed.
The situation can be prevented from happening if we disallow a dead
entry to have any possibility of updating gc_list. This is what the
patch intends to achieve.
Fixes: 9c29a2f55ec0 ("neighbor: Fix locking order for gc_list changes") Signed-off-by: Chinmay Agarwal <chinagar@codeaurora.org> Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20210127165453.GA20514@chinagar-linux.qualcomm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
One customer reports a crash problem which causes by flush request. It
triggers a warning before crash.
/* new request after previous flush is completed */
if (ktime_after(req_start, mddev->prev_flush_start)) {
WARN_ON(mddev->flush_bio);
mddev->flush_bio = bio;
bio = NULL;
}
The WARN_ON is triggered. We use spin lock to protect prev_flush_start and
flush_bio in md_flush_request. But there is no lock protection in
md_submit_flush_data. It can set flush_bio to NULL first because of
compiler reordering write instructions.
For example, flush bio1 sets flush bio to NULL first in
md_submit_flush_data. An interrupt or vmware causing an extended stall
happen between updating flush_bio and prev_flush_start. Because flush_bio
is NULL, flush bio2 can get the lock and submit to underlayer disks. Then
flush bio1 updates prev_flush_start after the interrupt or extended stall.
Then flush bio3 enters in md_flush_request. The start time req_start is
behind prev_flush_start. The flush_bio is not NULL(flush bio2 hasn't
finished). So it can trigger the WARN_ON now. Then it calls INIT_WORK
again. INIT_WORK() will re-initialize the list pointers in the
work_struct, which then can result in a corrupted work list and the
work_struct queued a second time. With the work list corrupted, it can
lead in invalid work items being used and cause a crash in
process_one_work.
We need to make sure only one flush bio can be handled at one same time.
So add spin lock in md_submit_flush_data to protect prev_flush_start and
flush_bio in an atomic way.
Reviewed-by: David Jeffery <djeffery@redhat.com> Signed-off-by: Xiao Ni <xni@redhat.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When an Intel IOMMU is virtualized, and a physical device is
passed-through to the VM, changes of the virtual IOMMU need to be
propagated to the physical IOMMU. The hypervisor therefore needs to
monitor PTE mappings in the IOMMU page-tables. Intel specifications
provide "caching-mode" capability that a virtual IOMMU uses to report
that the IOMMU is virtualized and a TLB flush is needed after mapping to
allow the hypervisor to propagate virtual IOMMU mappings to the physical
IOMMU. To the best of my knowledge no real physical IOMMU reports
"caching-mode" as turned on.
Synchronizing the virtual and the physical IOMMU tables is expensive if
the hypervisor is unaware which PTEs have changed, as the hypervisor is
required to walk all the virtualized tables and look for changes.
Consequently, domain flushes are much more expensive than page-specific
flushes on virtualized IOMMUs with passthrough devices. The kernel
therefore exploited the "caching-mode" indication to avoid domain
flushing and use page-specific flushing in virtualized environments. See
commit 78d5f0f500e6 ("intel-iommu: Avoid global flushes with caching
mode.")
This behavior changed after commit 13cf01744608 ("iommu/vt-d: Make use
of iova deferred flushing"). Now, when batched TLB flushing is used (the
default), full TLB domain flushes are performed frequently, requiring
the hypervisor to perform expensive synchronization between the virtual
TLB and the physical one.
Getting batched TLB flushes to use page-specific invalidations again in
such circumstances is not easy, since the TLB invalidation scheme
assumes that "full" domain TLB flushes are performed for scalability.
Disable batched TLB flushes when caching-mode is on, as the performance
benefit from using batched TLB invalidations is likely to be much
smaller than the overhead of the virtual-to-physical IOMMU page-tables
synchronization.
Fixes: 13cf01744608 ("iommu/vt-d: Make use of iova deferred flushing") Signed-off-by: Nadav Amit <namit@vmware.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Lu Baolu <baolu.lu@linux.intel.com> Cc: Joerg Roedel <joro@8bytes.org> Cc: Will Deacon <will@kernel.org> Cc: stable@vger.kernel.org Acked-by: Lu Baolu <baolu.lu@linux.intel.com> Link: https://lore.kernel.org/r/20210127175317.1600473-1-namit@vmware.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Nadav Amit <namit@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If we have only a single RX queue, such as when MSI-X is not
available, we should not send the RFH_QUEUEU_CONFIG_CMD, because our
only queue is the same as the command queue and will be configured as
part of the context info. Our code was actually trying to send the
command with 0 queues, which caused UMAC assert 0x1D04.
Fix that by not sending the command when we have a single queue.
Jan Kiszka reported that the x2apic_wrmsr_fence() function uses a plain
MFENCE while the Intel SDM (10.12.3 MSR Access in x2APIC Mode) calls for
MFENCE; LFENCE.
Short summary: we have special MSRs that have weaker ordering than all
the rest. Add fencing consistent with current SDM recommendations.
This is not known to cause any issues in practice, only in theory.
Longer story below:
The reason the kernel uses a different semantic is that the SDM changed
(roughly in late 2017). The SDM changed because folks at Intel were
auditing all of the recommended fences in the SDM and realized that the
x2apic fences were insufficient.
Why was the pain MFENCE judged insufficient?
WRMSR itself is normally a serializing instruction. No fences are needed
because the instruction itself serializes everything.
But, there are explicit exceptions for this serializing behavior written
into the WRMSR instruction documentation for two classes of MSRs:
IA32_TSC_DEADLINE and the X2APIC MSRs.
Back to x2apic: WRMSR is *not* serializing in this specific case.
But why is MFENCE insufficient? MFENCE makes writes visible, but
only affects load/store instructions. WRMSR is unfortunately not a
load/store instruction and is unaffected by MFENCE. This means that a
non-serializing WRMSR could be reordered by the CPU to execute before
the writes made visible by the MFENCE have even occurred in the first
place.
This means that an x2apic IPI could theoretically be triggered before
there is any (visible) data to process.
Does this affect anything in practice? I honestly don't know. It seems
quite possible that by the time an interrupt gets to consume the (not
yet) MFENCE'd data, it has become visible, mostly by accident.
To be safe, add the SDM-recommended fences for all x2apic WRMSRs.
This also leaves open the question of the _other_ weakly-ordered WRMSR:
MSR_IA32_TSC_DEADLINE. While it has the same ordering architecture as
the x2APIC MSRs, it seems substantially less likely to be a problem in
practice. While writes to the in-memory Local Vector Table (LVT) might
theoretically be reordered with respect to a weakly-ordered WRMSR like
TSC_DEADLINE, the SDM has this to say:
In x2APIC mode, the WRMSR instruction is used to write to the LVT
entry. The processor ensures the ordering of this write and any
subsequent WRMSR to the deadline; no fencing is required.
But, that might still leave xAPIC exposed. The safest thing to do for
now is to add the extra, recommended LFENCE.
[ bp: Massage commit message, fix typos, drop accidentally added
newline to tools/arch/x86/include/asm/barrier.h. ]
Reported-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20200305174708.F77040DD@viggo.jf.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
With retpolines disabled, some configurations of GCC, and specifically
the GCC versions 9 and 10 in Ubuntu will add Intel CET instrumentation
to the kernel by default. That breaks certain tracing scenarios by
adding a superfluous ENDBR64 instruction before the fentry call, for
functions which can be called indirectly.
CET instrumentation isn't currently necessary in the kernel, as CET is
only supported in user space. Disable it unconditionally and move it
into the x86's Makefile as CET/CFI... enablement should be a per-arch
decision anyway.
[ bp: Massage and extend commit message. ]
Fixes: 29be86d7f9cb ("kbuild: add -fcf-protection=none when using retpoline flags") Reported-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Nikolay Borisov <nborisov@suse.com> Tested-by: Nikolay Borisov <nborisov@suse.com> Cc: <stable@vger.kernel.org> Cc: Seth Forshee <seth.forshee@canonical.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Link: https://lkml.kernel.org/r/20210128215219.6kct3h2eiustncws@treble Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Sergey reported deadlock between kswapd correctly doing its usual
lock_page(page) followed by down_read(page->mapping->i_mmap_rwsem), and
madvise(MADV_REMOVE) on an madvise(MADV_HUGEPAGE) area doing
down_write(page->mapping->i_mmap_rwsem) followed by lock_page(page).
This happened when shmem_fallocate(punch hole)'s unmap_mapping_range()
reaches zap_pmd_range()'s call to __split_huge_pmd(). The same deadlock
could occur when partially truncating a mapped huge tmpfs file, or using
fallocate(FALLOC_FL_PUNCH_HOLE) on it.
__split_huge_pmd()'s page lock was added in 5.8, to make sure that any
concurrent use of reuse_swap_page() (holding page lock) could not catch
the anon THP's mapcounts and swapcounts while they were being split.
Fortunately, reuse_swap_page() is never applied to a shmem or file THP
(not even by khugepaged, which checks PageSwapCache before calling), and
anonymous THPs are never created in shmem or file areas: so that
__split_huge_pmd()'s page lock can only be necessary for anonymous THPs,
on which there is no risk of deadlock with i_mmap_rwsem.
Link: https://lkml.kernel.org/r/alpine.LSU.2.11.2101161409470.2022@eggly.anvils Fixes: c444eb564fb1 ("mm: thp: make the THP mapcount atomic against __split_huge_pmd_locked()") Signed-off-by: Hugh Dickins <hughd@google.com> Reported-by: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Reviewed-by: Andrea Arcangeli <aarcange@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In fast_isolate_freepages, high_pfn will be used if a prefered one (ie
PFN >= low_fn) not found.
But the high_pfn is not reset before searching an free area, so when it
was used as freepage, it may from another free area searched before. As
a result move_freelist_head(freelist, freepage) will have unexpected
behavior (eg corrupt the MOVABLE freelist)
Unable to handle kernel paging request at virtual address dead000000000200
Mem abort info:
ESR = 0x96000044
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000044
CM = 0, WnR = 1
[dead000000000200] address between user and kernel address ranges
The issue was reported on an smart phone product with 6GB ram and 3GB
zram as swap device.
This patch fixes the issue by reset high_pfn before searching each free
area, which ensure freepage and freelist match when call
move_freelist_head in fast_isolate_freepages().
Link: http://lkml.kernel.org/r/20190118175136.31341-12-mgorman@techsingularity.net Link: https://lkml.kernel.org/r/20210112094720.1238444-1-wu-yan@tcl.com Fixes: 5a811889de10f1eb ("mm, compaction: use free lists to quickly locate a migration target") Signed-off-by: Rokudo Yan <wu-yan@tcl.com> Acked-by: Mel Gorman <mgorman@techsingularity.net> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The page_huge_active() can be called from scan_movable_pages() which do
not hold a reference count to the HugeTLB page. So when we call
page_huge_active() from scan_movable_pages(), the HugeTLB page can be
freed parallel. Then we will trigger a BUG_ON which is in the
page_huge_active() when CONFIG_DEBUG_VM is enabled. Just remove the
VM_BUG_ON_PAGE.
Link: https://lkml.kernel.org/r/20210115124942.46403-6-songmuchun@bytedance.com Fixes: 7e1f049efb86 ("mm: hugetlb: cleanup using paeg_huge_active()") Signed-off-by: Muchun Song <songmuchun@bytedance.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Cc: David Hildenbrand <david@redhat.com> Cc: Yang Shi <shy828301@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When we isolate a HugeTLB page on CPU0. Meanwhile, we free it to the
buddy allocator on CPU1. Then, we can trigger a BUG_ON on CPU0, because
it is already freed to the buddy allocator.
Link: https://lkml.kernel.org/r/20210115124942.46403-5-songmuchun@bytedance.com Fixes: c8721bbbdd36 ("mm: memory-hotplug: enable memory hotplug to handle hugepage") Signed-off-by: Muchun Song <songmuchun@bytedance.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Cc: David Hildenbrand <david@redhat.com> Cc: Yang Shi <shy828301@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There is a race condition between __free_huge_page()
and dissolve_free_huge_page().
CPU0: CPU1:
// page_count(page) == 1
put_page(page)
__free_huge_page(page)
dissolve_free_huge_page(page)
spin_lock(&hugetlb_lock)
// PageHuge(page) && !page_count(page)
update_and_free_page(page)
// page is freed to the buddy
spin_unlock(&hugetlb_lock)
spin_lock(&hugetlb_lock)
clear_page_huge_active(page)
enqueue_huge_page(page)
// It is wrong, the page is already freed
spin_unlock(&hugetlb_lock)
The race window is between put_page() and dissolve_free_huge_page().
We should make sure that the page is already on the free list when it is
dissolved.
As a result __free_huge_page would corrupt page(s) already in the buddy
allocator.
Link: https://lkml.kernel.org/r/20210115124942.46403-4-songmuchun@bytedance.com Fixes: c8721bbbdd36 ("mm: memory-hotplug: enable memory hotplug to handle hugepage") Signed-off-by: Muchun Song <songmuchun@bytedance.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Acked-by: Michal Hocko <mhocko@suse.com> Cc: David Hildenbrand <david@redhat.com> Cc: Yang Shi <shy828301@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If a new hugetlb page is allocated during fallocate it will not be
marked as active (set_page_huge_active) which will result in a later
isolate_huge_page failure when the page migration code would like to
move that page. Such a failure would be unexpected and wrong.
Only export set_page_huge_active, just leave clear_page_huge_active as
static. Because there are no external users.
Link: https://lkml.kernel.org/r/20210115124942.46403-3-songmuchun@bytedance.com Fixes: 70c3547e36f5 (hugetlbfs: add hugetlbfs_fallocate()) Signed-off-by: Muchun Song <songmuchun@bytedance.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Cc: David Hildenbrand <david@redhat.com> Cc: Yang Shi <shy828301@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Building with gcc 4.9.2 reveals a latent bug in the PCI accessors
for Footbridge platforms, which causes a fatal alignment fault
while accessing IO memory. Fix this by making the assembly volatile.
Cc: stable@vger.kernel.org Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Set the emulator context to PROT64 if SYSENTER transitions from 32-bit
userspace (compat mode) to a 64-bit kernel, otherwise the RIP update at
the end of x86_emulate_insn() will incorrectly truncate the new RIP.
Note, this bug is mostly limited to running an Intel virtual CPU model on
an AMD physical CPU, as other combinations of virtual and physical CPUs
do not trigger full emulation. On Intel CPUs, SYSENTER in compatibility
mode is legal, and unconditionally transitions to 64-bit mode. On AMD
CPUs, SYSENTER is illegal in compatibility mode and #UDs. If the vCPU is
AMD, KVM injects a #UD on SYSENTER in compat mode. If the pCPU is Intel,
SYSENTER will execute natively and not trigger #UD->VM-Exit (ignoring
guest TLB shenanigans).
Fixes: fede8076aab4 ("KVM: x86: handle wrap around 32-bit address space") Cc: stable@vger.kernel.org Signed-off-by: Jonny Barker <jonny@jonnybarker.com>
[sean: wrote changelog] Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210202165546.2390296-1-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Don't let KVM load when running as an SEV guest, regardless of what
CPUID says. Memory is encrypted with a key that is not accessible to
the host (L0), thus it's impossible for L0 to emulate SVM, e.g. it'll
see garbage when reading the VMCB.
Technically, KVM could decrypt all memory that needs to be accessible to
the L0 and use shadow paging so that L0 does not need to shadow NPT, but
exposing such information to L0 largely defeats the purpose of running as
an SEV guest. This can always be revisited if someone comes up with a
use case for running VMs inside SEV guests.
Note, VMLOAD, VMRUN, etc... will also #GP on GPAs with C-bit set, i.e. KVM
is doomed even if the SEV guest is debuggable and the hypervisor is willing
to decrypt the VMCB. This may or may not be fixed on CPUs that have the
SVME_ADDR_CHK fix.
Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210202212017.2486595-1-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Some Kingston A2000 NVMe SSDs sooner or later get confused and stop
working when they use the deepest APST sleep while running Linux. The
system then crashes and one has to cold boot it to get the SSD working
again.
Kingston seems to known about this since at least mid-September 2020:
https://bbs.archlinux.org/viewtopic.php?pid=1926994#p1926994
Someone working for a German company representing Kingston to the German
press confirmed to me Kingston engineering is aware of the issue and
investigating; the person stated that to their current knowledge only
the deepest APST sleep state causes trouble. Therefore, make Linux avoid
it for now by applying the NVME_QUIRK_NO_DEEPEST_PS to this SSD.
I have two such SSDs, but it seems the problem doesn't occur with them.
I hence couldn't verify if this patch really fixes the problem, but all
the data in front of me suggests it should.
This patch can easily be reverted or improved upon if a better solution
surfaces.
FWIW, there are many reports about the issue scattered around the web;
most of the users disabled APST completely to make things work, some
just made Linux avoid the deepest sleep state:
projects / mirror_ubuntu-focal-kernel.git / log