Ard Biesheuvel [Tue, 24 Dec 2019 13:29:09 +0000 (14:29 +0100)]
x86/efistub: Disable paging at mixed mode entry
The EFI mixed mode entry code goes through the ordinary startup_32()
routine before jumping into the kernel's EFI boot code in 64-bit
mode. The 32-bit startup code must be entered with paging disabled,
but this is not documented as a requirement for the EFI handover
protocol, and so we should disable paging explicitly when entering
the kernel from 32-bit EFI firmware.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Cc: <stable@vger.kernel.org> Cc: Arvind Sankar <nivedita@alum.mit.edu> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Link: https://lkml.kernel.org/r/20191224132909.102540-4-ardb@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Hans de Goede [Tue, 24 Dec 2019 13:29:08 +0000 (14:29 +0100)]
efi/libstub/random: Initialize pointer variables to zero for mixed mode
Commit:
0d95981438c3 ("x86: efi/random: Invoke EFI_RNG_PROTOCOL to seed the UEFI RNG table")
causes the drivers/efi/libstub/random.c code to get used on x86 for the first time.
But this code was not written with EFI mixed mode in mind (running a 64
bit kernel on 32 bit EFI firmware), this causes the kernel to crash during
early boot when running in mixed mode.
The problem is that in mixed mode pointers are 64 bit, but when running on
a 32 bit firmware, EFI calls which return a pointer value by reference only
fill the lower 32 bits of the passed pointer, leaving the upper 32 bits
uninitialized which leads to crashes.
This commit fixes this by initializing pointers which are passed by
reference to EFI calls to NULL before passing them, so that the upper 32
bits are initialized to 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Cc: Arvind Sankar <nivedita@alum.mit.edu> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Fixes: 0d95981438c3 ("x86: efi/random: Invoke EFI_RNG_PROTOCOL to seed the UEFI RNG table") Link: https://lkml.kernel.org/r/20191224132909.102540-3-ardb@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Arvind Sankar [Tue, 24 Dec 2019 13:29:07 +0000 (14:29 +0100)]
efi/earlycon: Fix write-combine mapping on x86
On x86, until PAT is initialized, WC translates into UC-. Since we
calculate and store pgprot_writecombine(PAGE_KERNEL) when earlycon is
initialized, this means we actually use UC- mappings instead of WC
mappings, which makes scrolling very slow.
Instead store a boolean flag to indicate whether we want to use
writeback or write-combine mappings, and recalculate the actual pgprot_t
we need on every mapping. Once PAT is initialized, we will start using
write-combine mappings, which speeds up the scrolling considerably.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Fixes: 69c1f396f25b ("efi/x86: Convert x86 EFI earlyprintk into generic earlycon implementation") Link: https://lkml.kernel.org/r/20191224132909.102540-2-ardb@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Sun, 22 Dec 2019 18:59:06 +0000 (10:59 -0800)]
Merge tag 'xfs-5.5-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"Fix a few bugs that could lead to corrupt files, fsck complaints, and
filesystem crashes:
- Minor documentation fixes
- Fix a file corruption due to read racing with an insert range
operation.
- Fix log reservation overflows when allocating large rt extents
- Fix a buffer log item flags check
- Don't allow administrators to mount with sunit= options that will
cause later xfs_repair complaints about the root directory being
suspicious because the fs geometry appeared inconsistent
- Fix a non-static helper that should have been static"
* tag 'xfs-5.5-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: Make the symbol 'xfs_rtalloc_log_count' static
xfs: don't commit sunit/swidth updates to disk if that would cause repair failures
xfs: split the sunit parameter update into two parts
xfs: refactor agfl length computation function
libxfs: resync with the userspace libxfs
xfs: use bitops interface for buf log item AIL flag check
xfs: fix log reservation overflows when allocating large rt extents
xfs: stabilize insert range start boundary to avoid COW writeback race
xfs: fix Sphinx documentation warning
Linus Torvalds [Sun, 22 Dec 2019 18:41:48 +0000 (10:41 -0800)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bug fixes from Ted Ts'o:
"Ext4 bug fixes, including a regression fix"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: clarify impact of 'commit' mount option
ext4: fix unused-but-set-variable warning in ext4_add_entry()
jbd2: fix kernel-doc notation warning
ext4: use RCU API in debug_print_tree
ext4: validate the debug_want_extra_isize mount option at parse time
ext4: reserve revoke credits in __ext4_new_inode
ext4: unlock on error in ext4_expand_extra_isize()
ext4: optimize __ext4_check_dir_entry()
ext4: check for directory entries too close to block end
ext4: fix ext4_empty_dir() for directories with holes
Linus Torvalds [Sun, 22 Dec 2019 18:36:55 +0000 (10:36 -0800)]
Merge tag 'block-5.5-20191221' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Let's try this one again, this time without the compat_ioctl changes.
We've got those fixed up, but that can go out next week.
This contains:
- block queue flush lockdep annotation (Bart)
- Type fix for bsg_queue_rq() (Bart)
- Three dasd fixes (Stefan, Jan)
- nbd deadlock fix (Mike)
- Error handling bio user map fix (Yang)
- iocost fix (Tejun)
- sbitmap waitqueue addition fix that affects the kyber IO scheduler
(David)"
* tag 'block-5.5-20191221' of git://git.kernel.dk/linux-block:
sbitmap: only queue kyber's wait callback if not already active
block: fix memleak when __blk_rq_map_user_iov() is failed
s390/dasd: fix typo in copyright statement
s390/dasd: fix memleak in path handling error case
s390/dasd/cio: Interpret ccw_device_get_mdc return value correctly
block: Fix a lockdep complaint triggered by request queue flushing
block: Fix the type of 'sts' in bsg_queue_rq()
block: end bio with BLK_STS_AGAIN in case of non-mq devs and REQ_NOWAIT
nbd: fix shutdown and recv work deadlock v2
iocost: over-budget forced IOs should schedule async delay
- Fix scratch register clearing in M-mode (affects nommu users)
- Fix a mismerge on my part that broke the build for
CONFIG_SPARSEMEM_VMEMMAP users
Cleanup:
- Move SiFive L2 cache-related code to drivers/soc, per request"
* tag 'riscv/for-v5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: move sifive_l2_cache.c to drivers/soc
riscv: define vmemmap before pfn_to_page calls
riscv: fix scratch register clearing in M-mode.
riscv: Fix use of undefined config option CONFIG_CONFIG_MMU
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
Jan Stancek [Sun, 22 Dec 2019 12:33:24 +0000 (13:33 +0100)]
pipe: fix empty pipe check in pipe_write()
LTP pipeio_1 test is hanging with v5.5-rc2-385-gb8e382a185eb,
with read side observing empty pipe and sleeping and write
side running out of space and then sleeping as well. In this
scenario there are 5 writers and 1 reader.
Problem is that after pipe_write() reacquires pipe lock, it
re-checks for empty pipe with potentially stale 'head' and
doesn't wake up read side anymore. pipe->tail can advance
beyond 'head', because there are multiple writers.
Use pipe->head for empty pipe check after reacquiring lock
to observe current state.
Testing: With patch, LTP pipeio_1 ran successfully in loop for 1 hour.
Without patch it hanged within a minute.
Paolo Bonzini [Wed, 4 Dec 2019 14:33:35 +0000 (15:33 +0100)]
MAINTAINERS: remove Radim from KVM maintainers
Radim's kernel.org email is bouncing, which I take as a signal that
he is not really able to deal with KVM at this time. Make MAINTAINERS
match the effective value of KVM's bus factor.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
James Hogan [Sat, 21 Dec 2019 15:50:13 +0000 (15:50 +0000)]
MAINTAINERS: Orphan KVM for MIPS
I haven't been active for 18 months, and don't have the hardware set up
to test KVM for MIPS, so mark it as orphaned and remove myself as
maintainer. Hopefully somebody from MIPS can pick this up.
Signed-off-by: James Hogan <jhogan@kernel.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: "Radim Krčmář" <rkrcmar@redhat.com> Cc: Paul Burton <paulburton@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: kvm@vger.kernel.org Cc: linux-mips@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Yunfeng Ye [Tue, 17 Dec 2019 14:46:49 +0000 (22:46 +0800)]
ext4: fix unused-but-set-variable warning in ext4_add_entry()
Warning is found when compile with "-Wunused-but-set-variable":
fs/ext4/namei.c: In function ‘ext4_add_entry’:
fs/ext4/namei.c:2167:23: warning: variable ‘sbi’ set but not used
[-Wunused-but-set-variable]
struct ext4_sb_info *sbi;
^~~
Fix this by moving the variable @sbi under CONFIG_UNICODE.
Linus Torvalds [Sat, 21 Dec 2019 23:16:56 +0000 (15:16 -0800)]
Merge tag 'trace-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Fix memory leak on error path of process_system_preds()
- Lock inversion fix with updating tgid recording option
- Fix histogram compare function on big endian machines
- Fix histogram trigger function on big endian machines
- Make trace_printk() irq sync on init for kprobe selftest correctness
* tag 'trace-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix endianness bug in histogram trigger
samples/trace_printk: Wait for IRQ work to finish
tracing: Fix lock inversion in trace_event_enable_tgid_record()
tracing: Have the histogram compare functions convert to u64 first
tracing: Avoid memory leak in process_system_preds()
Linus Torvalds [Sat, 21 Dec 2019 23:12:26 +0000 (15:12 -0800)]
Merge tag 'libnvdimm-fix-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fix from Dan Williams:
"A minor regression fix.
The libnvdimm unit tests were expecting to mock calls to
ioremap_nocache() which disappeared in v5.5-rc1. This fix has appeared
in -next and collided with some cleanups that Christoph has planned
for v5.6, but he will fix up his branch once this goes in.
Summary:
- Restore the operation of the libnvdimm unit tests after the removal
of ioremap_nocache()"
* tag 'libnvdimm-fix-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
tools/testing/nvdimm: Fix mock support for ioremap
Sven Schnelle [Wed, 18 Dec 2019 07:44:27 +0000 (08:44 +0100)]
tracing: Fix endianness bug in histogram trigger
At least on PA-RISC and s390 synthetic histogram triggers are failing
selftests because trace_event_raw_event_synth() always writes a 64 bit
values, but the reader expects a field->size sized value. On little endian
machines this doesn't hurt, but on big endian this makes the reader always
read zero values.
Link: http://lore.kernel.org/linux-trace-devel/20191218074427.96184-4-svens@linux.ibm.com Cc: stable@vger.kernel.org Fixes: 4b147936fa509 ("tracing: Add support for 'synthetic' events") Acked-by: Tom Zanussi <tom.zanussi@linux.intel.com> Signed-off-by: Sven Schnelle <svens@linux.ibm.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
This gives a circular dependency deadlock between trace_types_lock and
event_mutex. To fix this invert the usage of trace_types_lock and
event_mutex in trace_options_core_write(). This keeps the sequence of
lock usage consistent.
Linus Torvalds [Sat, 21 Dec 2019 20:17:14 +0000 (12:17 -0800)]
Merge tag 's390-5.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Fix unwinding from irq context of interrupted user process.
- Add purgatory build missing symbols check. That helped to uncover and
fix missing symbols when built with kasan support enabled.
- Couple of ftrace fixes. Avoid broken stack trace and fix recursion
loop in function_graph tracer.
* tag 's390-5.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ftrace: save traced function caller
s390/unwind: stop gracefully at user mode pt_regs in irq stack
s390/purgatory: do not build purgatory with kcov, kasan and friends
s390/purgatory: Make sure we fail the build if purgatory has missing symbols
s390/ftrace: fix endless recursion in function_graph tracer
Linus Torvalds [Sat, 21 Dec 2019 18:52:10 +0000 (10:52 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes: a (rare) PSI crash fix, a CPU affinity related balancing
fix, and a toning down of active migration attempts"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/cfs: fix spurious active migration
sched/fair: Fix find_idlest_group() to handle CPU affinity
psi: Fix a division error in psi poll()
sched/psi: Fix sampling error and rare div0 crashes with cgroups and high uptime
Linus Torvalds [Sat, 21 Dec 2019 18:51:00 +0000 (10:51 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc fixes: a BTS fix, a PT NMI handling fix, a PMU sysfs fix and an
SRCU annotation"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Add SRCU annotation for pmus list walk
perf/x86/intel: Fix PT PMI handling
perf/x86/intel/bts: Fix the use of page_private()
perf/x86: Fix potential out-of-bounds access
Linus Torvalds [Sat, 21 Dec 2019 18:49:47 +0000 (10:49 -0800)]
Merge tag 'kbuild-fixes-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- fix warning in out-of-tree 'make clean'
- add READELF variable to the top Makefile
- fix broken builds when LINUX_COMPILE_BY contains a backslash
- fix build warning in kallsyms
- fix NULL pointer access in expr_eq() in Kconfig
- fix missing dependency on rsync in deb-pkg build
- remove ---help--- from documentation
- fix misleading documentation about directory descending
* tag 'kbuild-fixes-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: clarify the difference between obj-y and obj-m w.r.t. descending
kconfig: remove ---help--- from documentation
scripts: package: mkdebian: add missing rsync dependency
kconfig: don't crash on NULL expressions in expr_eq()
scripts/kallsyms: fix offset overflow of kallsyms_relative_base
mkcompile_h: use printf for LINUX_COMPILE_BY
mkcompile_h: git rid of UTS_TRUNCATE from LINUX_COMPILE_{BY,HOST}
x86/boot: kbuild: allow readelf executable to be specified
kbuild: fix 'No such file or directory' warning when cleaning
Masahiro Yamada [Thu, 19 Dec 2019 11:51:00 +0000 (20:51 +0900)]
kbuild: clarify the difference between obj-y and obj-m w.r.t. descending
Kbuild descends into a directory by either 'y' or 'm', but there is an
important difference.
Kbuild combines the built-in objects into built-in.a in each directory.
The built-in.a in the directory visited by obj-y is merged into the
built-in.a in the parent directory. This merge happens recursively
when Kbuild is ascending back towards the top directory, then built-in
objects are linked into vmlinux eventually. This works properly only
when the Makefile specifying obj-y is reachable by the chain of obj-y.
On the other hand, Kbuild does not take built-in.a from the directory
visited by obj-m. This it, all the objects in that directory are
supposed to be modular. If Kbuild descends into a directory by obj-m,
but the Makefile in the sub-directory specifies obj-y, those objects
are just left orphan.
The current statement "Kbuild only uses this information to decide that
it needs to visit the directory" is misleading. Clarify the difference.
Reported-by: Johan Hovold <johan@kernel.org> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Reviewed-by: Johan Hovold <johan@kernel.org>
Linus Torvalds [Sat, 21 Dec 2019 14:49:41 +0000 (06:49 -0800)]
Merge branch 'parisc-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pul parisc fixes from Helge Deller:
"Two build error fixes, one for the soft_offline_page() parameter
change and one for a specific KEXEC/KEXEC_FILE configuration, as well
as a compiler and a linker warning fix"
* 'parisc-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix compiler warnings in debug_core.c
parisc: soft_offline_page() now takes the pfn
parisc: add missing __init annotation
parisc: fix compilation when KEXEC=n and KEXEC_FILE=y
Linus Torvalds [Sat, 21 Dec 2019 14:24:56 +0000 (06:24 -0800)]
Merge tag 'for-linus-5.5b-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"This contains two cleanup patches and a small series for supporting
reloading the Xen block backend driver"
* tag 'for-linus-5.5b-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/grant-table: remove multiple BUG_ON on gnttab_interface
xen-blkback: support dynamic unbind/bind
xen/interface: re-define FRONT/BACK_RING_ATTACH()
xenbus: limit when state is forced to closed
xenbus: move xenbus_dev_shutdown() into frontend code...
xen/blkfront: Adjust indentation in xlvbd_alloc_gendisk
Linus Torvalds [Sat, 21 Dec 2019 14:17:05 +0000 (06:17 -0800)]
Merge tag 'powerpc-5.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Two weeks worth of accumulated fixes:
- A fix for a performance regression seen on PowerVM LPARs using
dedicated CPUs, caused by our vcpu_is_preempted() returning true
even for idle CPUs.
- One of the ultravisor support patches broke KVM on big endian hosts
in v5.4.
- Our KUAP (Kernel User Access Prevention) code missed allowing
access in __clear_user(), which could lead to an oops or erroneous
SEGV when triggered via PTRACE_GETREGSET.
- Two fixes for the ocxl driver, an open/remove race, and a memory
leak in an error path.
- A handful of other small fixes.
Thanks to: Andrew Donnellan, Christian Zigotzky, Christophe Leroy,
Christoph Hellwig, Daniel Axtens, David Hildenbrand, Frederic Barrat,
Gautham R. Shenoy, Greg Kurz, Ihor Pasichnyk, Juri Lelli, Marcus
Comstedt, Mike Rapoport, Parth Shah, Srikar Dronamraju, Vaidyanathan
Srinivasan"
* tag 'powerpc-5.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
KVM: PPC: Book3S HV: Fix regression on big endian hosts
powerpc: Fix __clear_user() with KUAP enabled
powerpc/pseries/cmm: fix managed page counts when migrating pages between zones
powerpc/8xx: fix bogus __init on mmu_mapin_ram_chunk()
ocxl: Fix potential memory leak on context creation
powerpc/irq: fix stack overflow verification
powerpc: Ensure that swiotlb buffer is allocated from low memory
powerpc/shared: Use static key to detect shared processor
powerpc/vcpu: Assume dedicated processors as non-preempt
ocxl: Fix concurrent AFU open and device removal
Linus Torvalds [Sat, 21 Dec 2019 14:04:12 +0000 (06:04 -0800)]
Merge branch 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 RAS fixes from Borislav Petkov:
"Three urgent RAS fixes for the AMD side of things:
- initialize struct mce.bank so that calculated error severity on AMD
SMCA machines is correct
- do not send IPIs early during bank initialization, when interrupts
are disabled
- a fix for when only a subset of MCA banks are enabled, which led to
boot hangs on some new AMD CPUs"
* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Fix possibly incorrect severity calculation on AMD
x86/MCE/AMD: Allow Reserved types to be overwritten in smca_banks[]
x86/MCE/AMD: Do not use rdmsr_safe_on_cpu() in smca_configure()
Linus Torvalds [Sat, 21 Dec 2019 13:55:35 +0000 (05:55 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"One core framework fix to walk the orphan list and match up clks to
parents when clk providers register the DT provider after registering
all their clks (as they should).
Then a handful of driver fixes for the qcom, imx, and at91 drivers.
The driver fixes are relatively small fixes for incorrect register
settings or missing locks causing race conditions"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: qcom: Avoid SMMU/cx gdsc corner cases
clk: qcom: gcc-sc7180: Fix setting flag for votable GDSCs
clk: Move clk_core_reparent_orphans() under CONFIG_OF
clk: at91: fix possible deadlock
clk: walk orphan list on clock provider registration
clk: imx: pll14xx: fix clk_pll14xx_wait_lock
clk: imx: clk-imx7ulp: Add missing sentinel of ulp_div_table
clk: imx: clk-composite-8m: add lock to gate/mux
sfc: Include XDP packet headroom in buffer step size.
Correct a mismatch between rx_page_buf_step and the actual step size
used when filling buffer pages.
This patch fixes the page overrun that occured when the MTU was set to
anything bigger than 1692.
Fixes: 3990a8fffbda ("sfc: allocate channels for XDP tx queues") Signed-off-by: Charles McLachlan <cmclachlan@solarflare.com> Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Fri, 20 Dec 2019 16:26:40 +0000 (16:26 +0000)]
sfc: fix channel allocation with brute force
It was possible for channel allocation logic to get confused between what
it had and what it wanted, and end up trying to use the same channel for
both PTP and regular TX. This led to a kernel panic:
BUG: unable to handle page fault for address: 0000000000047635
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 0 P4D 0
Oops: 0002 [#1] SMP PTI
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 5.4.0-rc3-ehc14+ #900
Hardware name: Dell Inc. PowerEdge R710/0M233H, BIOS 6.4.0 07/23/2013
RIP: 0010:native_queued_spin_lock_slowpath+0x188/0x1e0
Code: f3 90 48 8b 32 48 85 f6 74 f6 eb e8 c1 ee 12 83 e0 03 83 ee 01 48 c1 e0 05 48 63 f6 48 05 c0 98 02 00 48 03 04 f5 a0 c6 ed 81 <48> 89 10 8b 42 08 85 c0 75 09 f3 90 8b 42 08 85 c0 74 f7 48 8b 32
RSP: 0018:ffffc90000003d28 EFLAGS: 00010006
RAX: 0000000000047635 RBX: 0000000000000246 RCX: 0000000000040000
RDX: ffff888627a298c0 RSI: 0000000000003ffe RDI: ffff88861f6b8dd4
RBP: ffff8886225c6e00 R08: 0000000000040000 R09: 0000000000000000
R10: 0000000616f080c6 R11: 00000000000000c0 R12: ffff88861f6b8dd4
R13: ffffc90000003dc8 R14: ffff88861942bf00 R15: ffff8886150f2000
FS: 0000000000000000(0000) GS:ffff888627a00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000047635 CR3: 000000000200a000 CR4: 00000000000006f0
Call Trace:
<IRQ>
_raw_spin_lock_irqsave+0x22/0x30
skb_queue_tail+0x1b/0x50
sock_queue_err_skb+0x9d/0xf0
__skb_complete_tx_timestamp+0x9d/0xc0
efx_dequeue_buffer+0x126/0x180 [sfc]
efx_xmit_done+0x73/0x1c0 [sfc]
efx_ef10_ev_process+0x56a/0xfe0 [sfc]
? tick_sched_do_timer+0x60/0x60
? timerqueue_add+0x5d/0x70
? enqueue_hrtimer+0x39/0x90
efx_poll+0x111/0x380 [sfc]
? rcu_accelerate_cbs+0x50/0x160
net_rx_action+0x14a/0x400
__do_softirq+0xdd/0x2d0
irq_exit+0xa0/0xb0
do_IRQ+0x53/0xe0
common_interrupt+0xf/0xf
</IRQ>
In the long run we intend to rewrite the channel allocation code, but for
'net' fix this by allocating extra_channels, and giving them TX queues,
even if we do not in fact need them (e.g. on NICs without MAC TX
timestamping), and thereby using simpler logic to assign the channels
once they're allocated.
Fixes: 3990a8fffbda ("sfc: allocate channels for XDP tx queues") Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When storing a pointer to a dst_metrics structure in dst_entry._metrics,
two flags are added in the least significant bits of the pointer value.
Hence this assumes all pointers to dst_metrics structures have at least
4-byte alignment.
However, on m68k, the minimum alignment of 32-bit values is 2 bytes, not
4 bytes. Hence in some kernel builds, dst_default_metrics may be only
2-byte aligned, leading to obscure boot warnings like:
Fix this by forcing 4-byte alignment of all dst_metrics structures.
Fixes: e5fd387ad5b30ca3 ("ipv6: do not overwrite inetpeer metrics prematurely") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Fri, 20 Dec 2019 07:08:06 +0000 (15:08 +0800)]
selftests: pmtu: fix init mtu value in description
There is no a_r3, a_r4 in the testing topology.
It should be b_r1, b_r2. Also b_r1 mtu is 1400 and b_r2 mtu is 1500.
Fixes: e44e428f59e4 ("selftests: pmtu: add basic IPv4 and IPv6 PMTU tests") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Fri, 20 Dec 2019 02:28:10 +0000 (18:28 -0800)]
hv_netvsc: Fix unwanted rx_table reset
In existing code, the receive indirection table, rx_table, is in
struct rndis_device, which will be reset when changing MTU, ringparam,
etc. User configured receive indirection table values will be lost.
To fix this, move rx_table to struct net_device_context, and check
netif_is_rxfh_configured(), so rx_table will be set to default only
if no user configured value.
Fixes: ff4a44199012 ("netvsc: allow get/set of RSS indirection table") Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 19 Dec 2019 23:24:52 +0000 (23:24 +0000)]
net: phy: ensure that phy IDs are correctly typed
PHY IDs are 32-bit unsigned quantities. Ensure that they are always
treated as such, and not passed around as "int"s.
Fixes: 13d0ab6750b2 ("net: phy: check return code when requesting PHY driver module") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 19 Dec 2019 23:24:47 +0000 (23:24 +0000)]
mod_devicetable: fix PHY module format
When a PHY is probed, if the top bit is set, we end up requesting a
module with the string "mdio:-10101110000000100101000101010001" -
the top bit is printed to a signed -1 value. This leads to the module
not being loaded.
Fix the module format string and the macro generating the values for
it to ensure that we only print unsigned types and the top bit is
always 0/1. We correctly end up with
"mdio:10101110000000100101000101010001".
Fixes: 8626d3b43280 ("phylib: Support phy module autoloading") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Thu, 19 Dec 2019 18:35:16 +0000 (10:35 -0800)]
qede: Disable hardware gro when xdp prog is installed
commit 18c602dee472 ("qede: Use NETIF_F_GRO_HW.") introduced
a regression in driver that when xdp program is installed on
qede device, device's aggregation feature (hardware GRO) is not
getting disabled, which is unexpected with xdp.
Fixes: 18c602dee472 ("qede: Use NETIF_F_GRO_HW.") Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
ena: fixes of interrupt moderation bugs
Differences from V1:
1. Updated default tx interrupt moderation to 64us
2. Added "Fixes:" tags.
3. Removed cosmetic changes that are not relevant for these bug fixes
This patchset includes a couple of fixes of bugs in the implemenation of
interrupt moderation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
expected output: rx-usecs 128
actual output: rx-usecs 0
Reason for issue:
In stage 3, ethtool userspace calls first the ena_get_coalesce() handler
to get the current value of all properties, and then the ena_set_coalesce()
handler. When ena_get_coalesce() is called the adaptive interrupt
moderation is still on. There is an if in the code that returns the
rx_coalesce_usecs only if the adaptive interrupt moderation is off.
And since it is still on, rx_coalesce_usecs is not set, meaning it
stays 0.
Solution to issue:
Remove this if static interrupt moderation intervals have nothing to do
with dynamic ones.
expected output: rx-usecs 128
actual output: rx-usecs 0
Reason for issue:
In stage 2, when ena_set_coalesce() is called, the handler tests if
rx adaptive interrupt moderation is on, and if it is, it returns before
getting to the part in the function that sets the rx non-adaptive
interrupt moderation interval.
Solution to issue:
Remove the return from the function when rx adaptive interrupt moderation
is on.
Also cleaned up the fixed code in ena_set_coalesce by grouping together
adaptive interrupt moderation toggling, and using && instead of nested
ifs.
Fixes: b3db86dc4b82 ("net: ena: reimplement set/get_coalesce()") Fixes: 0eda847953d8 ("net: ena: fix retrieval of nonadaptive interrupt moderation intervals") Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Current default non-adaptive tx interrupt moderation interval is 196 us.
This value is too high and might cause the tx queue to fill up.
In this commit we set the default non-adaptive tx interrupt moderation
interval to 64 us in order to:
1. Reduce the probability of the queue filling-up (when compared to the
current default value of 196 us).
2. Reduce unnecessary tx interrupt overhead (which happens if we set the
default tx interval to 0).
We determined experimentally that 64 us is an optimal value that
reduces interrupt rate by more than 20% without affecting performance.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul [Thu, 19 Dec 2019 11:51:13 +0000 (12:51 +0100)]
net/smc: unregister ib devices in reboot_event
In the reboot_event handler, unregister the ib devices and enable
the IB layer to release the devices before the reboot.
Fixes: a33a803cfe64 ("net/smc: guarantee removal of link groups in reboot") Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: stmmac: platform: Fix MDIO init for platforms without PHY
The current implementation of "stmmac_dt_phy" function initializes
the MDIO platform bus data, even in the absence of PHY. This fix
will skip MDIO initialization if there is no PHY present.
Fixes: 7437127 ("net: stmmac: Convert to phylink and remove phylib logic") Acked-by: Jayati Sahu <jayati.sahu@samsung.com> Signed-off-by: Sriram Dash <sriram.dash@samsung.com> Signed-off-by: Padmanabhan Rajanbabu <p.rajanbabu@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
When a frame with NULL DSAP is received, llc_station_rcv is called.
In turn, llc_stat_ev_rx_null_dsap_xid_c is called to check if it is a NULL
XID frame. The return statement of llc_stat_ev_rx_null_dsap_xid_c returns 1
when the incoming frame is not a NULL XID frame and 0 otherwise. Hence, a
NULL XID response is returned unexpectedly, e.g. when the incoming frame is
a NULL TEST command.
To fix the error, simply remove the conditional operator.
A similar error in llc_stat_ev_rx_null_dsap_test_c is also fixed.
Signed-off-by: Chan Shu Tak, Alex <alexchan@task.com.hk> Signed-off-by: David S. Miller <davem@davemloft.net>
Pre-modification code:
int hip04_mac_start_xmit(struct sk_buff *skb, struct net_device *ndev)
{
[...]
[1] priv->tx_head = TX_NEXT(tx_head);
[2] count++;
[3] netdev_sent_queue(ndev, skb->len);
[...]
}
An rx interrupt occurs if hip04_mac_start_xmit just executes to the line 2,
tx_head has been updated, but corresponding 'skb->len' has not been
added to dql_queue.
And then
hip04_mac_interrupt->__napi_schedule->hip04_rx_poll->hip04_tx_reclaim
In hip04_tx_reclaim, because tx_head has been updated,
bytes_compl will plus an additional "skb-> len"
which has not been added to dql_queue. And then
trigger the BUG_ON(bytes_compl > num_queued - dql->num_completed).
To solve the problem described above, we put
"netdev_sent_queue(ndev, skb->len);"
before
"priv->tx_head = TX_NEXT(tx_head);"
Fixes: a41ea46a9a12 ("net: hisilicon: new hip04 ethernet driver") Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Remove special taglen define KSZ8795_INGRESS_TAG_LEN
and use generic KSZ_INGRESS_TAG_LEN instead.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 21 Dec 2019 05:00:28 +0000 (21:00 -0800)]
Merge branch 's390-fixes'
Julian Wiedmann says:
====================
s390/qeth: fixes 2019-12-18
please apply the following patch series to your net tree.
This brings two fixes for initialization / teardown issues, and one
ENOTSUPP cleanup.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 18 Dec 2019 15:32:28 +0000 (16:32 +0100)]
s390/qeth: don't return -ENOTSUPP to userspace
ENOTSUPP is not uapi, use EOPNOTSUPP instead.
Fixes: d66cb37e9664 ("qeth: Add new priority queueing options") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 18 Dec 2019 15:32:27 +0000 (16:32 +0100)]
s390/qeth: fix promiscuous mode after reset
When managing the promiscuous mode during an RX modeset, qeth caches the
current HW state to avoid repeated programming of the same state on each
modeset.
But while tearing down a device, we forget to clear the cached state. So
when the device is later set online again, the initial RX modeset
doesn't program the promiscuous mode since we believe it is already
enabled.
Fix this by clearing the cached state in the tear-down path.
Note that for the SBP variant of promiscuous mode, this accidentally
works right now because we unconditionally restore the SBP role while
re-initializing.
Fixes: 4a71df50047f ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 18 Dec 2019 15:32:26 +0000 (16:32 +0100)]
s390/qeth: handle error due to unsupported transport mode
Along with z/VM NICs, there's additional device types that only support
a specific transport mode (eg. external-bridged IQD).
Identify the corresponding error code, and raise a fitting error message
so that the user knows to adjust their device configuration.
On top of that also fix the subsequent error path, so that the rejected
cmd doesn't need to wait for a timeout but gets cancelled straight away.
Fixes: 4a71df50047f ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Jeffery [Tue, 17 Dec 2019 16:00:24 +0000 (11:00 -0500)]
sbitmap: only queue kyber's wait callback if not already active
Under heavy loads where the kyber I/O scheduler hits the token limits for
its scheduling domains, kyber can become stuck. When active requests
complete, kyber may not be woken up leaving the I/O requests in kyber
stuck.
This stuck state is due to a race condition with kyber and the sbitmap
functions it uses to run a callback when enough requests have completed.
The running of a sbt_wait callback can race with the attempt to insert the
sbt_wait. Since sbitmap_del_wait_queue removes the sbt_wait from the list
first then sets the sbq field to NULL, kyber can see the item as not on a
list but the call to sbitmap_add_wait_queue will see sbq as non-NULL. This
results in the sbt_wait being inserted onto the wait list but ws_active
doesn't get incremented. So the sbitmap queue does not know there is a
waiter on a wait list.
Since sbitmap doesn't think there is a waiter, kyber may never be
informed that there are domain tokens available and the I/O never advances.
With the sbt_wait on a wait list, kyber believes it has an active waiter
so cannot insert a new waiter when reaching the domain's full state.
This race can be fixed by only adding the sbt_wait to the queue if the
sbq field is NULL. If sbq is not NULL, there is already an action active
which will trigger the re-running of kyber. Let it run and add the
sbt_wait to the wait list if still needing to wait.
Reviewed-by: Omar Sandoval <osandov@fb.com> Signed-off-by: David Jeffery <djeffery@redhat.com> Reported-by: John Pittman <jpittman@redhat.com> Tested-by: John Pittman <jpittman@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Rahul Lakkireddy [Wed, 18 Dec 2019 03:49:29 +0000 (09:19 +0530)]
cxgb4: fix refcount init for TC-MQPRIO offload
Properly initialize refcount to 1 when hardware queue arrays for
TC-MQPRIO offload have been freshly allocated. Otherwise, following
warning is observed. Also fix up error path to only free hardware
queue arrays when refcount reaches 0.
v2:
- Move the refcount_set() closer to where the hardware queue arrays
are being allocated.
- Fix up error path to only free hardware queue arrays when refcount
reaches 0.
Fixes: 2d0cb84dd973 ("cxgb4: add ETHOFLD hardware queue support") Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 20 Dec 2019 21:36:49 +0000 (13:36 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Leftover put_cpu() in the perf/smmuv3 error path.
- Add Hisilicon TSV110 to spectre-v2 safe list
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: cpu_errata: Add Hisilicon TSV110 to spectre-v2 safe list
perf/smmuv3: Remove the leftover put_cpu() in error path
Linus Torvalds [Fri, 20 Dec 2019 21:33:50 +0000 (13:33 -0800)]
Merge tag 'drm-fixes-2019-12-21' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Probably the last one before Christmas, I'll see if there is much
demand over next few weeks for more fixes, I expect it'll be quiet
enough.
This has one exynos fix, and a bunch of i915 core and i915 GVT fixes.
Summary:
exynos:
- component delete fix
i915:
- Fix to drop an unused and harmful display W/A
- Fix to define EHL power wells independent of ICL
- Fix for priority inversion on bonded requests
- Fix in mmio offset calculation of DSB instance
- Fix memory leak from get_task_pid when banning clients
- Fixes to avoid dereference of uninitialized ops in dma_fence
tracing and keep reference to execbuf object until submitted.
- vGPU state setting locking fix (Zhenyu)
- Fix vGPU display dmabuf as read-only (Zhenyu)
- Properly handle vGPU display dmabuf page pin when rendering (Tina)
- Fix one guest boot warning to handle guc reset state (Fred)"
* tag 'drm-fixes-2019-12-21' of git://anongit.freedesktop.org/drm/drm:
drm/exynos: gsc: add missed component_del
drm/i915: Fix pid leak with banned clients
drm/i915/gem: Keep request alive while attaching fences
drm/i915: Fix WARN_ON condition for cursor plane ddb allocation
drm/i915/gvt: Fix guest boot warning
drm/i915/tgl: Drop Wa#1178
drm/i915/ehl: Define EHL powerwells independently of ICL
drm/i915: Set fence_work.ops before dma_fence_init
drm/i915: Copy across scheduler behaviour flags across submit fences
drm/i915/dsb: Fix in mmio offset calculation of DSB instance
drm/i915/gvt: Pin vgpu dma address before using
drm/i915/gvt: set guest display buffer as readonly
drm/i915/gvt: use vgpu lock for active state setting
Linus Torvalds [Fri, 20 Dec 2019 21:30:49 +0000 (13:30 -0800)]
Merge tag 'io_uring-5.5-20191220' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"Here's a set of fixes that should go into 5.5-rc3 for io_uring.
This is bigger than I'd like it to be, mainly because we're fixing the
case where an application reuses sqe data right after issue. This
really must work, or it's confusing. With 5.5 we're flagging us as
submit stable for the actual data, this must also be the case for
SQEs.
Honestly, I'd really like to add another series on top of this, since
it cleans it up considerable and prevents any SQE reuse by design. I
posted that here:
and may still send it your way early next week once it's been looked
at and had some more soak time (does pass all regression tests). With
that series, we've unified the prep+issue handling, and only the prep
phase even has access to the SQE.
Anyway, outside of that, fixes in here for a few other issues that
have been hit in testing or production"
* tag 'io_uring-5.5-20191220' of git://git.kernel.dk/linux-block:
io_uring: io_wq_submit_work() should not touch req->rw
io_uring: don't wait when under-submitting
io_uring: warn about unhandled opcode
io_uring: read opcode and user_data from SQE exactly once
io_uring: make IORING_OP_TIMEOUT_REMOVE deferrable
io_uring: make IORING_OP_CANCEL_ASYNC deferrable
io_uring: make IORING_POLL_ADD and IORING_POLL_REMOVE deferrable
io_uring: make HARDLINK imply LINK
io_uring: any deferred command must have stable sqe data
io_uring: remove 'sqe' parameter to the OP helpers that take it
io_uring: fix pre-prepped issue with force_nonblock == true
io-wq: re-add io_wq_current_is_worker()
io_uring: fix sporadic -EFAULT from IORING_OP_RECVMSG
io_uring: fix stale comment and a few typos
Dave Airlie [Fri, 20 Dec 2019 20:08:19 +0000 (06:08 +1000)]
Merge tag 'drm-intel-fixes-2019-12-19' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix to drop an unused and harmful display W/A
- Fix to define EHL power wells independent of ICL
- Fix for priority inversion on bonded requests
- Fix in mmio offset calculation of DSB instance
- Fix memory leak from get_task_pid when banning clients
- Fixes to avoid dereference of uninitialized ops in dma_fence tracing
and keep reference to execbuf object until submitted.
Helge Deller [Fri, 20 Dec 2019 20:00:19 +0000 (21:00 +0100)]
parisc: Fix compiler warnings in debug_core.c
Fix this compiler warning:
kernel/debug/debug_core.c: In function ‘kgdb_cpu_enter’:
arch/parisc/include/asm/cmpxchg.h:48:3: warning: value computed is not used [-Wunused-value]
48 | ((__typeof__(*(ptr)))__xchg((unsigned long)(x), (ptr), sizeof(*(ptr))))
arch/parisc/include/asm/atomic.h:78:30: note: in expansion of macro ‘xchg’
78 | #define atomic_xchg(v, new) (xchg(&((v)->counter), new))
| ^~~~
kernel/debug/debug_core.c:596:4: note: in expansion of macro ‘atomic_xchg’
596 | atomic_xchg(&kgdb_active, cpu);
| ^~~~~~~~~~~
If __blk_rq_map_user_iov() is failed in blk_rq_map_user_iov(),
the bio(s) which is allocated before this failing will leak. The
refcount of the bio(s) is init to 1 and increased to 2 by calling
bio_get(), but __blk_rq_unmap_user() only decrease it to 1, so
the bio cannot be freed. Fix it by calling blk_rq_unmap_user().
Reviewed-by: Bob Liu <bob.liu@oracle.com> Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stefan Haberland [Thu, 19 Dec 2019 08:43:52 +0000 (09:43 +0100)]
s390/dasd: fix typo in copyright statement
coypright -> copyright
Reported-by: Kate Stewart <kstewart@linuxfoundation.org> Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stefan Haberland [Thu, 19 Dec 2019 08:43:51 +0000 (09:43 +0100)]
s390/dasd: fix memleak in path handling error case
If for whatever reason the dasd_eckd_check_characteristics() function
exits after at least some paths have their configuration data
allocated those data is never freed again. In the error case the
device->private pointer is set to NULL and dasd_eckd_uncheck_device()
will exit without freeing the path data because of this NULL pointer.
Fix by calling dasd_eckd_clear_conf_data() for error cases.
Also use dasd_eckd_clear_conf_data() in dasd_eckd_uncheck_device()
to avoid code duplication.
Reported-by: Qian Cai <cai@lca.pw> Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com> Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jan Höppner [Thu, 19 Dec 2019 08:43:50 +0000 (09:43 +0100)]
s390/dasd/cio: Interpret ccw_device_get_mdc return value correctly
The max data count (mdc) is an unsigned 16-bit integer value as per AR
documentation and is received via ccw_device_get_mdc() for a specific
path mask from the CIO layer. The function itself also always returns a
positive mdc value or 0 in case mdc isn't supported or couldn't be
determined.
Though, the comment for this function describes a negative return value
to indicate failures.
As a result, the DASD device driver interprets the return value of
ccw_device_get_mdc() incorrectly. The error case is essentially a dead
code path.
To fix this behaviour, check explicitly for a return value of 0 and
change the comment for ccw_device_get_mdc() accordingly.
This fix merely enables the error code path in the DASD functions
get_fcx_max_data() and verify_fcx_max_data(). The actual functionality
stays the same and is still correct.
Reviewed-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com> Acked-by: Peter Oberparleiter <oberpar@linux.ibm.com> Reviewed-by: Stefan Haberland <sth@linux.ibm.com> Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@infradead.org> Cc: Ming Lei <ming.lei@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Bart Van Assche [Wed, 18 Dec 2019 00:23:29 +0000 (16:23 -0800)]
block: Fix the type of 'sts' in bsg_queue_rq()
This patch fixes the following sparse warnings:
block/bsg-lib.c:269:19: warning: incorrect type in initializer (different base types)
block/bsg-lib.c:269:19: expected int sts
block/bsg-lib.c:269:19: got restricted blk_status_t [usertype]
block/bsg-lib.c:286:16: warning: incorrect type in return expression (different base types)
block/bsg-lib.c:286:16: expected restricted blk_status_t
block/bsg-lib.c:286:16: got int [assigned] sts
Cc: Martin Wilck <mwilck@suse.com> Fixes: d46fe2cb2dce ("block: drop device references in bsg_queue_rq()") Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Linus Torvalds [Fri, 20 Dec 2019 18:42:25 +0000 (10:42 -0800)]
Merge tag 'iommu-fixes-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Fix kmemleak warning in IOVA code
- Fix compile warnings on ARM32/64 in dma-iommu code due to dma_mask
type mismatches
- Make ISA reserved regions relaxable, so that VFIO can assign devices
which have such regions defined
- Fix mapping errors resulting in IO page-faults in the VT-d driver
- Make sure direct mappings for a domain are created after the default
domain is updated
- Map ISA reserved regions in the VT-d driver with correct permissions
- Remove unneeded check for PSI capability in the IOTLB flush code of
the VT-d driver
- Lockdep fix iommu_dma_prepare_msi()
* tag 'iommu-fixes-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/dma: Relax locking in iommu_dma_prepare_msi()
iommu/vt-d: Remove incorrect PSI capability check
iommu/vt-d: Allocate reserved region for ISA with correct permission
iommu: set group default domain before creating direct mappings
iommu/vt-d: Fix dmar pte read access not set error
iommu/vt-d: Set ISA bridge reserved region as relaxable
iommu/dma: Rationalise types for DMA masks
iommu/iova: Init the struct iova to fix the possible memleak
Linus Torvalds [Fri, 20 Dec 2019 18:38:21 +0000 (10:38 -0800)]
Merge tag 'platform-drivers-x86-v5.5-2' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixes from Andy Shevchenko:
"Bucket of fixes for PDx86. Note, that there is no ABI breakage in
Mellanox driver because it has been introduced in v5.5-rc1, so we can
change it.
Summary:
- Add support of APUv4 and fix an assignment of simswap GPIO
- Add Siemens CONNECT X300 to DMI table to avoid stuck during boot
- Correct arguments of WMI call on HP Envy x360 15-cp0xxx model
- Fix the mlx-bootctl sysfs attributes to be device related"
* tag 'platform-drivers-x86-v5.5-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: pcengines-apuv2: Spelling fixes in the driver
platform/x86: pcengines-apuv2: detect apuv4 board
platform/x86: pcengines-apuv2: fix simswap GPIO assignment
platform/x86: pmc_atom: Add Siemens CONNECT X300 to critclk_systems DMI table
platform/x86: hp-wmi: Make buffer for HPWMI_FEATURE2_QUERY 128 bytes
platform/mellanox: fix the mlx-bootctl sysfs
Linus Torvalds [Fri, 20 Dec 2019 18:11:30 +0000 (10:11 -0800)]
Merge tag 'char-misc-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char and other driver fixes for 5.5-rc3.
The most noticable one is a much-reported fix for a random driver
issue that came up from 5.5-rc1 compat_ioctl cleanups. The others are
a chunk of habanalab driver fixes and intel_th driver fixes and new
device ids.
All have been in linux-next with no reported issues"
* tag 'char-misc-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
random: don't forget compat_ioctl on urandom
intel_th: msu: Fix window switching without windows
intel_th: Fix freeing IRQs
intel_th: pci: Add Elkhart Lake SOC support
intel_th: pci: Add Comet Lake PCH-V support
habanalabs: remove variable 'val' set but not used
habanalabs: rate limit error msg on waiting for CS
Linus Torvalds [Fri, 20 Dec 2019 18:09:21 +0000 (10:09 -0800)]
Merge tag 'staging-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some small staging driver fixes for a number of reported
issues.
The majority here are some fixes for the wfx driver, but also in here
is a comedi driver fix found during some code review, and an axis-fifo
build dependancy issue to resolve some reported testing problems.
All of these have been in linux-next with no reported issues"
* tag 'staging-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: wfx: fix wrong error message
staging: wfx: fix hif_set_mfp() with big endian hosts
staging: wfx: detect race condition in WEP authentication
staging: wfx: ensure that retry policy always fallbacks to MCS0 / 1Mbps
staging: wfx: fix rate control handling
staging: wfx: firmware does not support more than 32 total retries
staging: wfx: use boolean appropriately
staging: wfx: fix counter overflow
staging: wfx: fix case of lack of tx_retry_policies
staging: wfx: fix the cache of rate policies on interface reset
staging: axis-fifo: add unspecified HAS_IOMEM dependency
staging: comedi: gsc_hpdi: check dma_alloc_coherent() return value
Wei Li [Fri, 20 Dec 2019 09:17:10 +0000 (17:17 +0800)]
arm64: cpu_errata: Add Hisilicon TSV110 to spectre-v2 safe list
HiSilicon Taishan v110 CPUs didn't implement CSV2 field of the
ID_AA64PFR0_EL1, but spectre-v2 is mitigated by hardware, so
whitelist the MIDR in the safe list.
Signed-off-by: Wei Li <liwei391@huawei.com>
[hanjun: re-write the commit log] Signed-off-by: Hanjun Guo <guohanjun@huawei.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Linus Torvalds [Fri, 20 Dec 2019 17:55:28 +0000 (09:55 -0800)]
Merge tag 'tty-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial driver fixes for 5.5-rc3.
Only four small patches here:
- atmel serial driver fix
- msm_serial driver fix
- sprd serial driver fix
- tty core port fix
The last tty core fix should resolve a long-standing bug with a race
at port creation time that some people would see, and Sudip finally
tracked down.
All of these have been in linux-next with no reported issues"
* tag 'tty-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty/serial: atmel: fix out of range clock divider handling
tty: link tty and port before configuring it as console
serial: sprd: Add clearing break interrupt operation
tty: serial: msm_serial: Fix lockup for sysrq and oops
Linus Torvalds [Fri, 20 Dec 2019 17:53:24 +0000 (09:53 -0800)]
Merge tag 'usb-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for some reported issues.
Included in here are:
- xhci build warning fix
- ehci disconnect warning fix
- usbip lockup fix and error cleanup fix
- typec build fix
All of these have been in linux-next with no reported issues"
* tag 'usb-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: xhci: Fix build warning seen with CONFIG_PM=n
usbip: Fix error path of vhci_recv_ret_submit()
usbip: Fix receive error in vhci-hcd when using scatter-gather
USB: EHCI: Do not return -EPIPE when hub is disconnected
usb: typec: fusb302: Fix an undefined reference to 'extcon_get_state'
Linus Torvalds [Fri, 20 Dec 2019 17:49:05 +0000 (09:49 -0800)]
Merge tag 'pinctrl-v5.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Sorry that this fixes pull request took a while. Too much christmas
business going on.
This contains a few really important Intel fixes and some odd fixes:
- A host of fixes for the Intel baytrail and cherryview: properly
serialize all register accesses and add the irqchip with the
gpiochip as we need to, fix some pin lists and initialize the
hardware in the right order.
- Fix the Aspeed G6 LPC configuration.
- Handle a possible NULL pointer exception in the core.
- Fix the Kconfig dependencies for the Equilibrium driver"
* tag 'pinctrl-v5.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: ingenic: Fixup PIN_CONFIG_OUTPUT config
pinctrl: Modify Kconfig to fix linker error
pinctrl: pinmux: fix a possible null pointer in pinmux_can_be_used_for_gpio
pinctrl: aspeed-g6: Fix LPC/eSPI mux configuration
pinctrl: cherryview: Pass irqchip when adding gpiochip
pinctrl: cherryview: Add GPIO <-> pin mapping ranges via callback
pinctrl: cherryview: Split out irq hw-init into a separate helper function
pinctrl: baytrail: Pass irqchip when adding gpiochip
pinctrl: baytrail: Add GPIO <-> pin mapping ranges via callback
pinctrl: baytrail: Update North Community pin list
pinctrl: baytrail: Really serialize all register accesses
Michael Haener [Fri, 29 Nov 2019 09:16:49 +0000 (10:16 +0100)]
platform/x86: pmc_atom: Add Siemens CONNECT X300 to critclk_systems DMI table
The CONNECT X300 uses the PMC clock for on-board components and gets
stuck during boot if the clock is disabled. Therefore, add this
device to the critical systems list.
Tested on CONNECT X300.
Fixes: 648e921888ad ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL") Signed-off-by: Michael Haener <michael.haener@siemens.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Hans de Goede [Tue, 17 Dec 2019 19:06:04 +0000 (20:06 +0100)]
platform/x86: hp-wmi: Make buffer for HPWMI_FEATURE2_QUERY 128 bytes
At least on the HP Envy x360 15-cp0xxx model the WMI interface
for HPWMI_FEATURE2_QUERY requires an outsize of at least 128 bytes,
otherwise it fails with an error code 5 (HPWMI_RET_INVALID_PARAMETERS):
Dec 06 00:59:38 kernel: hp_wmi: query 0xd returned error 0x5
We do not care about the contents of the buffer, we just want to know
if the HPWMI_FEATURE2_QUERY command is supported.
This commits bumps the buffer size, fixing the error.
Fixes: 8a1513b4932 ("hp-wmi: limit hotkey enable") Cc: stable@vger.kernel.org BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1520703 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Liming Sun [Wed, 18 Dec 2019 18:35:27 +0000 (13:35 -0500)]
platform/mellanox: fix the mlx-bootctl sysfs
This is a follow-up commit for the sysfs attributes to change
from DRIVER_ATTR to DEVICE_ATTR according to some initial comments.
In such case, it's better to point the sysfs path to the device
itself instead of the driver. The ABI document is also updated.
Fixes: 79e29cb8fbc5 ("platform/mellanox: Add bootctl driver for Mellanox BlueField Soc") Signed-off-by: Liming Sun <lsun@mellanox.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Chen Wandun [Fri, 20 Dec 2019 16:07:31 +0000 (08:07 -0800)]
xfs: Make the symbol 'xfs_rtalloc_log_count' static
Fix the following sparse warning:
fs/xfs/libxfs/xfs_trans_resv.c:206:1: warning: symbol 'xfs_rtalloc_log_count' was not declared. Should it be static?
Fixes: b1de6fc7520f ("xfs: fix log reservation overflows when allocating large rt extents") Signed-off-by: Chen Wandun <chenwandun@huawei.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Aditya Pakki [Tue, 17 Dec 2019 20:53:56 +0000 (14:53 -0600)]
xen/grant-table: remove multiple BUG_ON on gnttab_interface
gnttab_request_version() always sets the gnttab_interface variable
and the assertions to check for empty gnttab_interface is unnecessary.
The patch eliminates multiple such assertions.
Paul Durrant [Wed, 11 Dec 2019 15:29:56 +0000 (15:29 +0000)]
xen-blkback: support dynamic unbind/bind
By simply re-attaching to shared rings during connect_ring() rather than
assuming they are freshly allocated (i.e assuming the counters are zero)
it is possible for vbd instances to be unbound and re-bound from and to
(respectively) a running guest.
This has been tested by running:
while true;
do fio --name=randwrite --ioengine=libaio --iodepth=16 \
--rw=randwrite --bs=4k --direct=1 --size=1G --verify=crc32;
done
in a PV guest whilst running:
while true;
do echo vbd-$DOMID-$VBD >unbind;
echo unbound;
sleep 5;
echo vbd-$DOMID-$VBD >bind;
echo bound;
sleep 3;
done
in dom0 from /sys/bus/xen-backend/drivers/vbd to continuously unbind and
re-bind its system disk image.
This is a highly useful feature for a backend module as it allows it to be
unloaded and re-loaded (i.e. updated) without requiring domUs to be halted.
This was also tested by running:
while true;
do echo vbd-$DOMID-$VBD >unbind;
echo unbound;
sleep 5;
rmmod xen-blkback;
echo unloaded;
sleep 1;
modprobe xen-blkback;
echo bound;
cd $(pwd);
sleep 3;
done
in dom0 whilst running the same loop as above in the (single) PV guest.
Some (less stressful) testing has also been done using a Windows HVM guest
with the latest 9.0 PV drivers installed.
Signed-off-by: Paul Durrant <pdurrant@amazon.com> Reviewed-by: Juergen Gross <jgross@suse.com> Reviewed-by: Roger Pau Monné <roger.pau@citrix.com> Signed-off-by: Juergen Gross <jgross@suse.com>
Paul Durrant [Wed, 11 Dec 2019 15:29:55 +0000 (15:29 +0000)]
xen/interface: re-define FRONT/BACK_RING_ATTACH()
Currently these macros are defined to re-initialize a front/back ring
(respectively) to values read from the shared ring in such a way that any
requests/responses that are added to the shared ring whilst the front/back
is detached will be skipped over. This, in general, is not a desirable
semantic since most frontend implementations will eventually block waiting
for a response which would either never appear or never be processed.
Since the macros are currently unused, take this opportunity to re-define
them to re-initialize a front/back ring using specified values. This also
allows FRONT/BACK_RING_INIT() to be re-defined in terms of
FRONT/BACK_RING_ATTACH() using a specified value of 0.
NOTE: BACK_RING_ATTACH() will be used directly in a subsequent patch.
Paul Durrant [Wed, 11 Dec 2019 15:29:54 +0000 (15:29 +0000)]
xenbus: limit when state is forced to closed
If a driver probe() fails then leave the xenstore state alone. There is no
reason to modify it as the failure may be due to transient resource
allocation issues and hence a subsequent probe() may succeed.
If the driver supports re-binding then only force state to closed during
remove() only in the case when the toolstack may need to clean up. This can
be detected by checking whether the state in xenstore has been set to
closing prior to device removal.
NOTE: Re-bind support is indicated by new boolean in struct xenbus_driver,
which defaults to false. Subsequent patches will add support to
some backend drivers.
Paul Durrant [Wed, 11 Dec 2019 15:29:53 +0000 (15:29 +0000)]
xenbus: move xenbus_dev_shutdown() into frontend code...
...and make it static
xenbus_dev_shutdown() is seemingly intended to cause clean shutdown of PV
frontends when a guest is rebooted. Indeed the function waits for a
conpletion which is only set by a call to xenbus_frontend_closed().
This patch removes the shutdown() method from backends and moves
xenbus_dev_shutdown() from xenbus_probe.c into xenbus_probe_frontend.c,
renaming it appropriately and making it static.
NOTE: In the case where the backend is running in a driver domain, the
toolstack should have already terminated any frontends that may be
using it (since Xen does not support re-startable PV driver domains)
so xenbus_dev_shutdown() should never be called.
xen/blkfront: Adjust indentation in xlvbd_alloc_gendisk
Clang warns:
../drivers/block/xen-blkfront.c:1117:4: warning: misleading indentation;
statement is not part of the previous 'if' [-Wmisleading-indentation]
nr_parts = PARTS_PER_DISK;
^
../drivers/block/xen-blkfront.c:1115:3: note: previous statement is here
if (err)
^
This is because there is a space at the beginning of this line; remove
it so that the indentation is consistent according to the Linux kernel
coding style and clang no longer warns.
While we are here, the previous line has some trailing whitespace; clean
that up as well.
Fixes: c80a420995e7 ("xen-blkfront: handle Xen major numbers other than XENVBD") Link: https://github.com/ClangBuiltLinux/linux/issues/791 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Juergen Gross <jgross@suse.com> Acked-by: Roger Pau Monné <roger.pau@citrix.com> Signed-off-by: Juergen Gross <jgross@suse.com>
The sifive_l2_cache.c is in no way related to RISC-V architecture
memory management. It is a little stub driver working around the fact
that the EDAC maintainers prefer their drivers to be structured in a
certain way that doesn't fit the SiFive SOCs.
Move the file to drivers/soc and add a Kconfig option for it, as well
as the whole drivers/soc boilerplate for CONFIG_SOC_SIFIVE.
Fixes: a967a289f169 ("RISC-V: sifive_l2_cache: Add L2 cache controller driver for SiFive SoCs") Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Borislav Petkov <bp@suse.de>
[paul.walmsley@sifive.com: keep the MAINTAINERS change specific to the L2$ controller code] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
pfn_to_page & page_to_pfn depend on vmemmap being available before the calls
if kernel is configured with CONFIG_SPARSEMEM_VMEMMAP=y. This was caused
by NOMMU changes which moved vmemmap definition bellow functions definitions
calling pfn_to_page & page_to_pfn.
Noticed while compiled 5.5-rc2 kernel for Fedora/RISCV.
v2:
- Add a comment for vmemmap in source
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com> Fixes: 6bd33e1ece52 ("riscv: add nommu support") Reviewed-by: Anup Patel <anup@brainfault.org> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Greentime Hu [Thu, 19 Dec 2019 06:44:59 +0000 (14:44 +0800)]
riscv: fix scratch register clearing in M-mode.
This patch fixes that the sscratch register clearing in M-mode. It cleared
sscratch register in M-mode, but it should clear mscratch register. That will
cause kernel trap if the CPU core doesn't support S-mode when trying to access
sscratch.
Fixes: 9e80635619b5 ("riscv: clear the instruction cache and all registers when booting") Signed-off-by: Greentime Hu <greentime.hu@sifive.com> Reviewed-by: Anup Patel <anup@brainfault.org> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
a refcount leak in the error path of u32_change() has been recently
introduced. It can be observed with the following commands:
[root@f31 ~]# tc filter replace dev eth0 ingress protocol ip prio 97 \
> u32 match ip src 127.0.0.1/32 indev notexist20 flowid 1:1 action drop
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
[root@f31 ~]# tc filter replace dev eth0 ingress protocol ip prio 98 \
> handle 42:42 u32 divisor 256
Error: cls_u32: Divisor can only be used on a hash table.
We have an error talking to the kernel
[root@f31 ~]# tc filter replace dev eth0 ingress protocol ip prio 99 \
> u32 ht 47:47
Error: cls_u32: Specified hash table not found.
We have an error talking to the kernel
they all legitimately return -EINVAL; however, they leave semi-configured
filters at eth0 tc ingress:
[root@f31 ~]# tc filter show dev eth0 ingress
filter protocol ip pref 97 u32 chain 0
filter protocol ip pref 97 u32 chain 0 fh 800: ht divisor 1
filter protocol ip pref 98 u32 chain 0
filter protocol ip pref 98 u32 chain 0 fh 801: ht divisor 1
filter protocol ip pref 99 u32 chain 0
filter protocol ip pref 99 u32 chain 0 fh 802: ht divisor 1
With older kernels, filters were unconditionally considered empty (and
thus de-refcounted) on the error path of ->change().
After commit 8b64678e0af8 ("net: sched: refactor tp insert/delete for
concurrent execution"), filters were considered empty when the walk()
function didn't set 'walker.stop' to 1.
Finally, with commit 6676d5e416ee ("net: sched: set dedicated tcf_walker
flag when tp is empty"), tc filters are considered empty unless the walker
function is called with a non-NULL handle. This last change doesn't fit
cls_u32 design, because at least the "root hnode" is (almost) always
non-NULL, as it's allocated in u32_init().
- patch 1/2 is a proposal to restore the original kernel behavior, where
no filter was installed in the error path of u32_change().
- patch 2/2 adds tdc selftests that can be ued to verify the correct
behavior of u32 in the error path of ->change().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Tue, 17 Dec 2019 23:00:05 +0000 (00:00 +0100)]
tc-testing: initial tdc selftests for cls_u32
- move test "e9a3 - Add u32 with source match" to u32.json, and change the
match pattern to catch all hnodes
- add testcases for relevant error paths of cls_u32 module
Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Tue, 17 Dec 2019 23:00:04 +0000 (00:00 +0100)]
net/sched: cls_u32: fix refcount leak in the error path of u32_change()
when users replace cls_u32 filters with new ones having wrong parameters,
so that u32_change() fails to validate them, the kernel doesn't roll-back
correctly, and leaves semi-configured rules.
Fix this in u32_walk(), avoiding a call to the walker function on filters
that don't have a match rule connected. The side effect is, these "empty"
filters are not even dumped when present; but that shouldn't be a problem
as long as we are restoring the original behaviour, where semi-configured
filters were not even added in the error path of u32_change().
Fixes: 6676d5e416ee ("net: sched: set dedicated tcf_walker flag when tp is empty") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Aditya Pakki [Tue, 17 Dec 2019 20:43:00 +0000 (14:43 -0600)]
nfc: s3fwrn5: replace the assertion with a WARN_ON
In s3fwrn5_fw_recv_frame, if fw_info->rsp is not empty, the
current code causes a crash via BUG_ON. However, s3fwrn5_fw_send_msg
does not crash in such a scenario. The patch replaces the BUG_ON
by returning the error to the callers and frees up skb.
Signed-off-by: Aditya Pakki <pakki001@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: macb: fix probing of PHY not described in the dt
The macb Ethernet driver supports various ways of referencing its
network PHY. When a device tree is used the PHY can be referenced with
a phy-handle or, if connected to its internal MDIO bus, described in
a child node. Some platforms omitted the PHY description while
connecting the PHY to the internal MDIO bus and in such cases the MDIO
bus has to be scanned "manually" by the macb driver.
Prior to the phylink conversion the driver registered the MDIO bus with
of_mdiobus_register and then in case the PHY couldn't be retrieved
using dt or using phy_find_first (because registering an MDIO bus with
of_mdiobus_register masks all PHYs) the macb driver was "manually"
scanning the MDIO bus (like mdiobus_register does). The phylink
conversion did break this particular case but reimplementing the manual
scan of the bus in the macb driver wouldn't be very clean. The solution
seems to be registering the MDIO bus based on if the PHYs are described
in the device tree or not.
There are multiple ways to do this, none is perfect. I chose to check if
any of the child nodes of the macb node was a network PHY and based on
this to register the MDIO bus with the of_ helper or not. The drawback
is boards referencing the PHY through phy-handle, would scan the entire
MDIO bus of the macb at boot time (as the MDIO bus would be registered
with mdiobus_register). For this solution to work properly
of_mdiobus_child_is_phy has to be exported, which means the patch doing
so has to be backported to -stable as well.
Another possible solution could have been to simply check if the macb
node has a child node by counting its sub-nodes. This isn't techically
perfect, as there could be other sub-nodes (in practice this should be
fine, fixed-link being taken care of in the driver). We could also
simply s/of_mdiobus_register/mdiobus_register/ but that could break
boards using the PHY description in child node as a selector (which
really would be not a proper way to do this...).
The real issue here being having PHYs not described in the dt but we
have dt backward compatibility, so we have to live with that.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-hirsute-kernel.git / log