of_get_named_gpio could return -E_PROBE_DEFER or another
error code. This error should be passed further instead
of being ignored.
Signed-off-by: Ionut Nicu <ioan.nicu.ext@nsn.com> Acked-by: Peter Korsgaard <peter.korsgaard@barco.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Initially commit cb527ede1bf6ff2008a025606f25344b8ed7b4ac
"i2c-omap: Double clear of ARDY status in IRQ handler"
added a workaround for undocumented errata ProDB0017052.
But then commit 1d7afc95946487945cc7f5019b41255b72224b70
"i2c: omap: ack IRQ in parts" refactored code and missed
one of ARDY clearings. So current code violates errata.
It causes often i2c bus timeouts on my Pandaboard.
Jean Delvare [Thu, 10 Oct 2013 06:04:06 +0000 (08:04 +0200)]
i2c: Not all adapters have a parent
The code in acpi_i2c_register_devices() assumes that all i2c adapters
have a parent. This is not necessarily the case, for example the
i2c-stub driver instantiate a virtual i2c adapter without a parent.
Check for this to avoid a NULL pointer deference.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang [Tue, 8 Oct 2013 20:35:36 +0000 (22:35 +0200)]
i2c: i2c-stu300: replace platform_driver_probe to support deferred probing
Subsystems like pinctrl and gpio rightfully make use of deferred probing at
core level. Now, deferred drivers won't be retried if they don't have a .probe
function specified in the driver struct. Fix this driver to have that, so the
devices it supports won't get lost in a deferred probe.
Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang [Tue, 8 Oct 2013 20:35:35 +0000 (22:35 +0200)]
i2c: i2c-mxs: replace platform_driver_probe to support deferred probing
Subsystems like pinctrl and gpio rightfully make use of deferred probing at
core level. Now, deferred drivers won't be retried if they don't have a .probe
function specified in the driver struct. Fix this driver to have that, so the
devices it supports won't get lost in a deferred probe.
Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang [Tue, 8 Oct 2013 20:35:34 +0000 (22:35 +0200)]
i2c: i2c-imx: replace platform_driver_probe to support deferred probing
Subsystems like pinctrl and gpio rightfully make use of deferred probing at
core level. Now, deferred drivers won't be retried if they don't have a .probe
function specified in the driver struct. Fix this driver to have that, so the
devices it supports won't get lost in a deferred probe.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang [Tue, 8 Oct 2013 20:35:33 +0000 (22:35 +0200)]
i2c: i2c-designware-platdrv: replace platform_driver_probe to support deferred probing
Subsystems like pinctrl and gpio rightfully make use of deferred probing at
core level. Now, deferred drivers won't be retried if they don't have a .probe
function specified in the driver struct. Fix this driver to have that, so the
devices it supports won't get lost in a deferred probe.
Reported-by: Zhangfei Gao <zhangfei.gao@linaro.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the outstanding target fixes queued up for v3.12-rc4 code.
The highlights include:
- Make vhost/scsi tag percpu_ida_alloc() use GFP_ATOMIC
- Allow sess_cmd_map allocation failure fallback to use vzalloc
- Fix COMPARE_AND_WRITE se_cmd->data_length bug with FILEIO backends
- Fixes for COMPARE_AND_WRITE callback recursive failure OOPs + non
zero scsi_status bug
- Make iscsi-target do acknowledgement tag release from RX context
- Setup iscsi-target with extra (cmdsn_depth / 2) percpu_ida tags
Also included is a iscsi-target patch CC'ed for v3.10+ that avoids
legacy wait_for_task=true release during fast-past StatSN
acknowledgement, and two other SRP target related patches that address
long-standing issues that are CC'ed for v3.3+.
Extra thanks to Thomas Glanzmann for his testing feedback with
COMPARE_AND_WRITE + EXTENDED_COPY VAAI logic"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target; Allow an extra tag_num / 2 number of percpu_ida tags
iscsi-target: Perform release of acknowledged tags from RX context
iscsi-target: Only perform wait_for_tasks when performing shutdown
target: Fail on non zero scsi_status in compare_and_write_callback
target: Fix recursive COMPARE_AND_WRITE callback failure
target: Reset data_length for COMPARE_AND_WRITE to NoLB * block_size
ib_srpt: always set response for task management
target: Fall back to vzalloc upon ->sess_cmd_map kzalloc failure
vhost/scsi: Use GFP_ATOMIC with percpu_ida_alloc for obtaining tag
ib_srpt: Destroy cm_id before destroying QP.
target: Fix xop->dbl assignment in target_xcopy_parse_segdesc_02
Linus Torvalds [Sun, 6 Oct 2013 20:35:15 +0000 (13:35 -0700)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine fixes from Vinod Koul:
"Here is the slave dmanegine fixes. We have the fix for deadlock issue
on imx-dma by Michael and Josh's edma config fix along with author
change"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: imx-dma: fix callback path in tasklet
dmaengine: imx-dma: fix lockdep issue between irqhandler and tasklet
dmaengine: imx-dma: fix slow path issue in prep_dma_cyclic
dma/Kconfig: Make TI_EDMA select TI_PRIV_EDMA
edma: Update author email address
Linus Torvalds [Sat, 5 Oct 2013 19:17:24 +0000 (12:17 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This is a small collection of fixes, including a regression fix from
Liu Bo that solves rare crashes with compression on.
I've merged my for-linus up to 3.12-rc3 because the top commit is only
meant for 3.12. The rest of the fixes are also available in my master
branch on top of my last 3.11 based pull"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: Fix crash due to not allocating integrity data for a bioset
Btrfs: fix a use-after-free bug in btrfs_dev_replace_finishing
Btrfs: eliminate races in worker stopping code
Btrfs: fix crash of compressed writes
Btrfs: fix transid verify errors when recovering log tree
Linus Torvalds [Sat, 5 Oct 2013 19:11:40 +0000 (12:11 -0700)]
Merge tag 'gpio-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Two patches for the OMAP driver, dealing with setting up IRQs properly
on the device tree boot path"
* tag 'gpio-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio/omap: auto-setup a GPIO when used as an IRQ
gpio/omap: maintain GPIO and IRQ usage separately
Linus Torvalds [Sat, 5 Oct 2013 18:54:10 +0000 (11:54 -0700)]
Merge tag 'usb-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are none fixes for various USB driver problems. The majority are
gadget/musb fixes, but there are some new device ids in here as well"
* tag 'usb-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: chipidea: add Intel Clovertrail pci id
usb: gadget: s3c-hsotg: fix can_write limit for non-periodic endpoints
usb: gadget: f_fs: fix error handling
usb: musb: dsps: do not bind to "musb-hdrc"
USB: serial: option: Ignore card reader interface on Huawei E1750
usb: musb: gadget: fix otg active status flag
usb: phy: gpio-vbus: fix deferred probe from __init
usb: gadget: pxa25x_udc: fix deferred probe from __init
usb: musb: fix otg default state
Linus Torvalds [Sat, 5 Oct 2013 18:26:19 +0000 (11:26 -0700)]
Merge tag 'tty-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty fixes from Greg KH:
"Here are two tty driver fixes for 3.12-rc4.
One fixes the reported regression in the n_tty code that a number of
people found recently, and the other one fixes an issue with xen
consoles that broke in 3.10"
* tag 'tty-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
xen/hvc: allow xenboot console to be used again
tty: Fix pty master read() after slave closes
Darrick J. Wong [Fri, 20 Sep 2013 03:37:07 +0000 (20:37 -0700)]
btrfs: Fix crash due to not allocating integrity data for a bioset
When btrfs creates a bioset, we must also allocate the integrity data pool.
Otherwise btrfs will crash when it tries to submit a bio to a checksumming
disk:
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Linus Torvalds [Sat, 5 Oct 2013 03:50:16 +0000 (20:50 -0700)]
Merge branch 'for-linus' of git://git.samba.org/sfrench/cifs-2.6
Pull CIFS fixes from Steve French:
"Small set of cifs fixes. Most important is Jeff's fix that works
around disconnection problems which can be caused by simultaneous use
of user space tools (starting a long running smbclient backup then
doing a cifs kernel mount) or multiple cifs mounts through a NAT, and
Jim's fix to deal with reexport of cifs share.
I expect to send two more cifs fixes next week (being tested now) -
fixes to address an SMB2 unmount hang when server dies and a fix for
cifs symlink handling of Windows "NFS" symlinks"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
[CIFS] update cifs.ko version
[CIFS] Remove ext2 flags that have been moved to fs.h
[CIFS] Provide sane values for nlink
cifs: stop trying to use virtual circuits
CIFS: FS-Cache: Uncache unread pages in cifs_readpages() before freeing them
Linus Torvalds [Sat, 5 Oct 2013 03:48:20 +0000 (20:48 -0700)]
Merge tag 'pci-v3.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"We merged what was intended to be an MMCONFIG cleanup, but in fact,
for systems without _CBA (which is almost everything), it broke
extended config space for domain 0 and it broke all config space for
other domains.
This reverts the change"
* tag 'pci-v3.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "x86/PCI: MMCONFIG: Check earlier for MMCONFIG region at address zero"
07f9b61c was intended to be a cleanup that didn't change anything, but in
fact, for systems without _CBA (which is almost everything), it broke
extended config space for domain 0 and all config space for other domains.
Linus Torvalds [Fri, 4 Oct 2013 22:03:42 +0000 (15:03 -0700)]
Merge tag 'pm+acpi-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- The resume part of user space driven hibernation (s2disk) is now
broken after the change that moved the creation of memory bitmaps to
after the freezing of tasks, because I forgot that the resume utility
loaded the image before freezing tasks and needed the bitmaps for
that. The fix adds special handling for that case.
- One of recent commits changed the export of acpi_bus_get_device() to
EXPORT_SYMBOL_GPL(), which was technically correct but broke existing
binary modules using that function including one in particularly
widespread use. Change it back to EXPORT_SYMBOL().
- The intel_pstate driver sometimes fails to disable turbo if its
no_turbo sysfs attribute is set. Fix from Srinivas Pandruvada.
- One of recent cpufreq fixes forgot to update a check in cpufreq-cpu0
which still (incorrectly) treats non-NULL as non-error. Fix from
Philipp Zabel.
- The SPEAr cpufreq driver uses a wrong variable type in one place
preventing it from catching errors returned by one of the functions
called by it. Fix from Sachin Kamat.
* tag 'pm+acpi-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: Use EXPORT_SYMBOL() for acpi_bus_get_device()
intel_pstate: fix no_turbo
cpufreq: cpufreq-cpu0: NULL is a valid regulator, part 2
cpufreq: SPEAr: Fix incorrect variable type
PM / hibernate: Fix user space driven resume regression
Linus Torvalds [Fri, 4 Oct 2013 21:47:22 +0000 (14:47 -0700)]
Merge tag 'xfs-for-linus-v3.12-rc4' of git://oss.sgi.com/xfs/xfs
Pull xfs bugfixes from Ben Myers:
"There are lockdep annotations for project quotas, a fix for dirent
dtype support on v4 filesystems, a fix for a memory leak in recovery,
and a fix for the build error that resulted from it. D'oh"
* tag 'xfs-for-linus-v3.12-rc4' of git://oss.sgi.com/xfs/xfs:
xfs: Use kmem_free() instead of free()
xfs: fix memory leak in xlog_recover_add_to_trans
xfs: dirent dtype presence is dependent on directory magic numbers
xfs: lockdep needs to know about 3 dquot-deep nesting
Ilya Dryomov [Wed, 2 Oct 2013 17:41:01 +0000 (20:41 +0300)]
Btrfs: fix a use-after-free bug in btrfs_dev_replace_finishing
free_device rcu callback, scheduled from btrfs_rm_dev_replace_srcdev,
can be processed before btrfs_scratch_superblock is called, which would
result in a use-after-free on btrfs_device contents. Fix this by
zeroing the superblock before the rcu callback is registered.
Cc: Stefan Behrens <sbehrens@giantdisaster.de> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Ilya Dryomov [Wed, 2 Oct 2013 16:39:50 +0000 (19:39 +0300)]
Btrfs: eliminate races in worker stopping code
The current implementation of worker threads in Btrfs has races in
worker stopping code, which cause all kinds of panics and lockups when
running btrfs/011 xfstest in a loop. The problem is that
btrfs_stop_workers is unsynchronized with respect to check_idle_worker,
check_busy_worker and __btrfs_start_workers.
E.g., check_idle_worker race flow:
btrfs_stop_workers(): check_idle_worker(aworker):
- grabs the lock
- splices the idle list into the
working list
- removes the first worker from the
working list
- releases the lock to wait for
its kthread's completion
- grabs the lock
- if aworker is on the working list,
moves aworker from the working list
to the idle list
- releases the lock
- grabs the lock
- puts the worker
- removes the second worker from the
working list
......
btrfs_stop_workers returns, aworker is on the idle list
FS is umounted, memory is freed
......
aworker is waken up, fireworks ensue
With this applied, I wasn't able to trigger the problem in 48 hours,
whereas previously I could reliably reproduce at least one of these
races within an hour.
Reported-by: David Sterba <dsterba@suse.cz> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Liu Bo [Tue, 1 Oct 2013 15:49:49 +0000 (23:49 +0800)]
Btrfs: fix crash of compressed writes
The crash[1] is found by xfstests/generic/208 with "-o compress",
it's not reproduced everytime, but it does panic.
The bug is quite interesting, it's actually introduced by a recent commit
(573aecafca1cf7a974231b759197a1aebcf39c2a,
Btrfs: actually limit the size of delalloc range).
Btrfs implements delay allocation, so during writeback, we
(1) get a page A and lock it
(2) search the state tree for delalloc bytes and lock all pages within the range
(3) process the delalloc range, including find disk space and create
ordered extent and so on.
(4) submit the page A.
It runs well in normal cases, but if we're in a racy case, eg.
buffered compressed writes and aio-dio writes,
sometimes we may fail to lock all pages in the 'delalloc' range,
in which case, we need to fall back to search the state tree again with
a smaller range limit(max_bytes = PAGE_CACHE_SIZE - offset).
The mentioned commit has a side effect, that is, in the fallback case,
we can find delalloc bytes before the index of the page we already have locked,
so we're in the case of (delalloc_end <= *start) and return with (found > 0).
This ends with not locking delalloc pages but making ->writepage still
process them, and the crash happens.
This fixes it by just thinking that we find nothing and returning to caller
as the caller knows how to deal with it properly.
Josef Bacik [Mon, 30 Sep 2013 18:10:43 +0000 (14:10 -0400)]
Btrfs: fix transid verify errors when recovering log tree
If we crash with a log, remount and recover that log, and then crash before we
can commit another transaction we will get transid verify errors on the next
mount. This is because we were not zero'ing out the log when we committed the
transaction after recovery. This is ok as long as we commit another transaction
at some point in the future, but if you abort or something else goes wrong you
can end up in this weird state because the recovery stuff says that the tree log
should have a generation+1 of the super generation, which won't be the case of
the transaction that was started for recovery. Fix this by removing the check
and _always_ zero out the log portion of the super when we commit a transaction.
This fixes the transid verify issues I was seeing with my force errors tests.
Thanks,
Linus Torvalds [Fri, 4 Oct 2013 19:54:11 +0000 (12:54 -0700)]
selinux: remove 'flags' parameter from inode_has_perm
Every single user passes in '0'. I think we had non-zero users back in
some stone age when selinux_inode_permission() was implemented in terms
of inode_has_perm(), but that complicated case got split up into a
totally separate code-path so that we could optimize the much simpler
special cases.
See commit 2e33405785d3 ("SELinux: delay initialization of audit data in
selinux_inode_permission") for example.
Free the memory in error path of xlog_recover_add_to_trans().
Normally this memory is freed in recovery pass2, but is leaked
in the error path.
Signed-off-by: Mark Tinguely <tinguely@sgi.com> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 519ccb81ac1c8e3e4eed294acf93be00b43dcad6)
Dave Chinner [Sun, 29 Sep 2013 23:37:04 +0000 (09:37 +1000)]
xfs: dirent dtype presence is dependent on directory magic numbers
The determination of whether a directory entry contains a dtype
field originally was dependent on the filesystem having CRCs
enabled. This meant that the format for dtype beign enabled could be
determined by checking the directory block magic number rather than
doing a feature bit check. This was useful in that it meant that we
didn't need to pass a struct xfs_mount around to functions that
were already supplied with a directory block header.
Unfortunately, the introduction of dtype fields into the v4
structure via a feature bit meant this "use the directory block
magic number" method of discriminating the dirent entry sizes is
broken. Hence we need to convert the places that use magic number
checks to use feature bit checks so that they work correctly and not
by chance.
The current code works on v4 filesystems only because the dirent
size roundup covers the extra byte needed by the dtype field in the
places where this problem occurs.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Ben Myers <bpm@sgi.com> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 367993e7c6428cb7617ab7653d61dca54e2fdede)
The lockdep annotation for dquot lock nesting only understands
locking for user and "other" dquots, not user, group and quota
dquots. Fix the annotations to match the locking heirarchy we now
have.
Reported-by: Michael L. Semon <mlsemon35@gmail.com> Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Ben Myers <bpm@sgi.com> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit f112a049712a5c07de25d511c3c6587a2b1a015e)
Linus Torvalds [Fri, 4 Oct 2013 16:06:13 +0000 (09:06 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse bugfixes from Miklos Szeredi:
"This contains two more fixes by Maxim for writeback/truncate races and
fixes for RCU walk in fuse_dentry_revalidate()"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: no RCU mode in fuse_access()
fuse: readdirplus: fix RCU walk
fuse: don't check_submounts_and_drop() in RCU walk
fuse: fix fallocate vs. ftruncate race
fuse: wait for writeback in fuse_file_fallocate()
Linus Torvalds [Fri, 4 Oct 2013 16:05:12 +0000 (09:05 -0700)]
Merge tag 'iommu-fixes-v3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"A couple of fixes from the IOMMU side:
- some small fixes for the new ARM-SMMU driver
- a register offset correction for VT-d
- add MAINTAINERS entry for drivers/iommu
Overall no really big or intrusive changes"
* tag 'iommu-fixes-v3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
x86/iommu: correct ICS register offset
MAINTAINERS: add overall IOMMU section
iommu/arm-smmu: don't enable SMMU device until probing has completed
iommu/arm-smmu: fix iommu_present() test in init
iommu/arm-smmu: fix a signedness bug
* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: Remove duplicate DEBUG_STACK_USAGE config
arm64: include VIRTIO_{MMIO,BLK} in defconfig
arm64: include EXT4 in defconfig
arm64: fix possible invalid FPSIMD initialization state
arm64: use correct register width when retrieving ASID
arm64: avoid multiple evaluation of ptr in get_user/put_user()
Linus Torvalds [Fri, 4 Oct 2013 16:03:51 +0000 (09:03 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"Two small fixes for 3.12 only this week. I have a few more fixes
pending but those are conceptually more complex so will have to wait
for a bit longer"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix forgotten preempt_enable() when CPU has inclusive pcaches
MIPS: Alchemy: MTX-1: fix incorrect placement of __initdata tag
Linus Torvalds [Fri, 4 Oct 2013 16:03:07 +0000 (09:03 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Two simplefb fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/simplefb: Mark framebuffer mem-resources as IORESOURCE_BUSY to avoid bootup warning
x86/simplefb: Fix overflow causing bogus fall-back
We need to free the ld_active list head before jumping into the callback
routine. Otherwise the callback could run into issue_pending and change
our ld_active list head we just going to free. This will run the channel
list into an currupted and undefined state.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dmaengine: imx-dma: fix lockdep issue between irqhandler and tasklet
The tasklet and irqhandler are using spin_lock while other routines are
using spin_lock_irqsave/restore. This leads to lockdep issues as
described bellow. This patch is changing the code to use
spinlock_irq_save/restore in both code pathes.
As imxdma_xfer_desc always gets called with spin_lock_irqsave lock held,
this patch also removes the spare call inside the routine to avoid
double locking.
dmaengine: imx-dma: fix slow path issue in prep_dma_cyclic
When perparing cyclic_dma buffers by the sound layer, it will dump the
following lockdep trace. The leading snd_pcm_action_single get called
with read_lock_irq called. To fix this, we change the kcalloc call from
GFP_KERNEL to GFP_ATOMIC.
David Vrabel [Tue, 1 Oct 2013 18:00:49 +0000 (19:00 +0100)]
xen/hvc: allow xenboot console to be used again
Commit d0380e6c3c0f6edb986d8798a23acfaf33d5df23 (early_printk:
consolidate random copies of identical code) added in 3.10 introduced
a check for con->index == -1 in early_console_register().
Initialize index to -1 for the xenboot console so earlyprintk=xen
works again.
Ian Abbott [Wed, 2 Oct 2013 13:57:51 +0000 (14:57 +0100)]
staging: comedi: ni_65xx: (bug fix) confine insn_bits to one subdevice
The `insn_bits` handler `ni_65xx_dio_insn_bits()` has a `for` loop that
currently writes (optionally) and reads back up to 5 "ports" consisting
of 8 channels each. It reads up to 32 1-bit channels but can only read
and write a whole port at once - it needs to handle up to 5 ports as the
first channel it reads might not be aligned on a port boundary. It
breaks out of the loop early if the next port it handles is beyond the
final port on the card. It also breaks out early on the 5th port in the
loop if the first channel was aligned. Unfortunately, it doesn't check
that the current port it is dealing with belongs to the comedi subdevice
the `insn_bits` handler is acting on. That's a bug.
Redo the `for` loop to terminate after the final port belonging to the
subdevice, changing the loop variable in the process to simplify things
a bit. The `for` loop could now try and handle more than 5 ports if the
subdevice has more than 40 channels, but the test `if (bitshift >= 32)`
ensures it will break out early after 4 or 5 ports (depending on whether
the first channel is aligned on a port boundary). (`bitshift` will be
between -7 and 7 inclusive on the first iteration, increasing by 8 for
each subsequent operation.)
iscsi-target; Allow an extra tag_num / 2 number of percpu_ida tags
This patch bumps the default number of tags allocated per session by
iscsi-target via transport_alloc_session_tags() -> percpu_ida_init()
by another (tag_num / 2).
This is done to take into account the tags waiting to be acknowledged
and released in iscsit_ack_from_expstatsn(), but who's number are not
directly limited by the CmdSN Window queue_depth being enforced by
the target.
Using a larger value here is also useful to prevent percpu_ida_alloc()
from having to steal tags from other CPUs when no tags are available
on the local CPU, while waiting for unacknowledged tags to be released.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
iscsi-target: Perform release of acknowledged tags from RX context
This patch converts iscsit_ack_from_expstatsn() to populate a local
ack_list of commands, and call iscsit_free_cmd() directly from RX
thread context, instead of using iscsit_add_cmd_to_immediate_queue()
to queue the acknowledged commands to be released from TX thread
context.
It is helpful to release the acknowledge commands as quickly as
possible, along with the associated percpu_ida tags, in order to
prevent percpu_ida_alloc() from having to steal tags from other
CPUs while waiting for iscsit_free_cmd() to happen from TX thread
context.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
iscsi-target: Only perform wait_for_tasks when performing shutdown
This patch changes transport_generic_free_cmd() to only wait_for_tasks
when shutdown=true is passed to iscsit_free_cmd().
With the advent of >= v3.10 iscsi-target code using se_cmd->cmd_kref,
the extra wait_for_tasks with shutdown=false is unnecessary, and may
end up causing an extra context switch when releasing WRITEs.
Cc: stable@vger.kernel.org # 3.10+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Linus Torvalds [Thu, 3 Oct 2013 15:55:50 +0000 (08:55 -0700)]
Merge branch 'for-curr' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fix from Vineet Gupta:
"Chrisitian found/fixed issue with SA_SIGINFO based signal handler
corrupting the user space registers post after signal handling"
* 'for-curr' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Fix signal frame management for SA_SIGINFO
Linus Torvalds [Thu, 3 Oct 2013 15:54:39 +0000 (08:54 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"Here are a few powerpc fixes, all aimed at -stable, found in part
thanks to the ramping up of a major distro testing and in part thanks
to the LE guys hitting all sort interesting corner cases.
The most scary are probably the register clobber issues in
csum_partial_copy_generic(), especially since Anton even had a test
case for that thing, which didn't manage to hit the bugs :-)
Another highlight is that memory hotplug should work again with these
fixes.
Oh and the vio modalias one is worse than the cset implies as it
upsets distro installers, so I've been told at least, which is why I'm
shooting it to stable"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/tm: Switch out userspace PPR and DSCR sooner
powerpc/tm: Turn interrupts hard off in tm_reclaim()
powerpc/perf: Fix handling of FAB events
powerpc/vio: Fix modalias_show return values
powerpc/iommu: Use GFP_KERNEL instead of GFP_ATOMIC in iommu_init_table()
powerpc/sysfs: Disable writing to PURR in guest mode
powerpc: Restore registers on error exit from csum_partial_copy_generic()
powerpc: Fix parameter clobber in csum_partial_copy_generic()
powerpc: Fix memory hotplug with sparse vmemmap
target: Fail on non zero scsi_status in compare_and_write_callback
This patch addresses a bug for backends such as IBLOCK that perform
asynchronous completion via transport_complete_cmd(), that will call
target_complete_failure_work() -> transport_generic_request_failure(),
upon exception status and invoke cmd->transport_complete_callback()
-> compare_and_write_callback() incorrectly during the failure case.
It adds a check for a non zero se_cmd->scsi_status within the first
invocation of compare_and_write_callback(), and will jump to out plus
up se_device->caw_sem before exiting the callback.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de> Tested-by: Thomas Glanzmann <thomas@glanzmann.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a bug when compare_and_write_callback() invoked from
target_complete_ok_work() hits an failure from __target_execute_cmd() ->
cmd->execute_cmd(), that ends up calling transport_generic_request_failure()
-> compare_and_write_post(), thus causing SCF_COMPARE_AND_WRITE_POST to
incorrectly be set.
The result of this bug is that target_complete_ok_work() no longer hits
the if (!rc && !(cmd->se_cmd_flags & SCF_COMPARE_AND_WRITE_POST) check
that forces an immediate return, and instead double completes the se_cmd
in question, triggering an OOPs in the process.
This patch changes compare_and_write_post() to only set this bit when a
failure has not already occured to ensure the immediate return from within
target_complete_ok_work(), and thus allow transport_generic_request_failure()
to handle the sending of the CHECK_CONDITION exception status.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de> Tested-by: Thomas Glanzmann <thomas@glanzmann.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target: Reset data_length for COMPARE_AND_WRITE to NoLB * block_size
This patch resets se_cmd->data_length for COMPARE_AND_WRITE emulation
within sbc_compare_and_write() to NoLB * block_size in order to address
a bug with FILEIO backends where a I/O failure will occur when data_length
does not match the I/O size being actually dispatched for the individual
per block READs + WRITEs.
This is done late enough in sbc_compare_and_write() after the memory
allocations have occured in transport_generic_new_cmd() to not cause
any unwanted side-effects.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de> Tested-by: Thomas Glanzmann <thomas@glanzmann.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Jack Wang [Mon, 30 Sep 2013 08:09:05 +0000 (10:09 +0200)]
ib_srpt: always set response for task management
The SRP specification requires:
"Response data shall be provided in any SRP_RSP response that is sent in
response to an SRP_TSK_MGMT request (see 6.7). The information in the
RSP_CODE field (see table 24) shall indicate the completion status of
the task management function."
So fix this to avoid the SRP initiator interprets task management functions
that succeeded as failed.
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com> Cc: stable@vger.kernel.org # 3.3+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Michael Neuling [Thu, 26 Sep 2013 03:29:09 +0000 (13:29 +1000)]
powerpc/tm: Switch out userspace PPR and DSCR sooner
When we do a treclaim or trecheckpoint we end up running with userspace
PPR and DSCR values. Currently we don't do anything special to avoid
running with user values which could cause a severe performance
degradation.
This patch moves the PPR and DSCR save and restore around treclaim and
trecheckpoint so that we run with user values for a much shorter period.
More care is taken with the PPR as it's impact is greater than the DSCR.
This is similar to user exceptions, where we run HTM_MEDIUM early to
ensure that we don't run with a userspace PPR values in the kernel.
Signed-off-by: Michael Neuling <mikey@neuling.org> Cc: <stable@vger.kernel.org> # 3.9+ Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 4df4899 "Add power8 EBB support" included a bug in the handling
of the FAB_CRESP_MATCH and FAB_TYPE_MATCH fields.
These values are pulled out of the event code using EVENT_THR_CTL_SHIFT,
however we were then or'ing that value directly into MMCR1.
This meant we were failing to set the FAB fields correctly, and also
potentially corrupting the value for PMC4SEL. Leading to no counts for
the FAB events and incorrect counts for PMC4.
The fix is simply to shift left the FAB value correctly before or'ing it
with MMCR1.
Reported-by: Sooraj Ravindran Nair <soonair3@in.ibm.com> Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Cc: <stable@vger.kernel.org> # 3.10+ Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
modalias_show() should return an empty string on error, not -ENODEV.
This causes the following false and annoying error:
> find /sys/devices -name modalias -print0 | xargs -0 cat >/dev/null
cat: /sys/devices/vio/4000/modalias: No such device
cat: /sys/devices/vio/4001/modalias: No such device
cat: /sys/devices/vio/4002/modalias: No such device
cat: /sys/devices/vio/4004/modalias: No such device
cat: /sys/devices/vio/modalias: No such device
Signed-off-by: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> CC: <stable@vger.kernel.org>
Before the panic() we got a page allocation failure for an order-2
allocation. There appears to be memory free, but perhaps not in the
ATOMIC context. I looked through all the call-sites of
iommu_init_table() and didn't see any obvious reason to need an ATOMIC
allocation. Most call-sites in fact have an explicit GFP_KERNEL
allocation shortly before the call to iommu_init_table(), indicating we
are not in an atomic context. There is some indirection for some paths,
but I didn't see any locks indicating that GFP_KERNEL is inappropriate.
With this change under the same conditions, we have not been able to
reproduce the panic.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> CC: <stable@vger.kernel.org>
powerpc/sysfs: Disable writing to PURR in guest mode
arch/powerpc/kernel/sysfs.c exports PURR with write permission.
This may be valid for kernel in phyp mode. But writing to
the file in guest mode causes crash due to a priviledge violation
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> CC: <stable@vger.kernel.org>
powerpc: Restore registers on error exit from csum_partial_copy_generic()
The csum_partial_copy_generic() function saves the PowerPC non-volatile
r14, r15, and r16 registers for the main checksum-and-copy loop.
Unfortunately, it fails to restore them upon error exit from this loop,
which results in silent corruption of these registers in the presumably
rare event of an access exception within that loop.
This commit therefore restores these register on error exit from the loop.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Anton Blanchard <anton@samba.org> Cc: stable@vger.kernel.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc: Fix parameter clobber in csum_partial_copy_generic()
The csum_partial_copy_generic() uses register r7 to adjust the remaining
bytes to process. Unfortunately, r7 also holds a parameter, namely the
address of the flag to set in case of access exceptions while reading
the source buffer. Lacking a quantum implementation of PowerPC, this
commit instead uses register r9 to do the adjusting, leaving r7's
pointer uncorrupted.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Anton Blanchard <anton@samba.org> Cc: stable@vger.kernel.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Previous commit 46723bfa540... introduced a new config option
HAVE_BOOTMEM_INFO_NODE that ended up breaking memory hot-remove for ppc
when sparse vmemmap is not defined.
This patch defines HAVE_BOOTMEM_INFO_NODE for ppc and adds the call to
register_page_bootmem_info_node. Without this we get a BUG_ON for memory
hot remove in put_page_bootmem().
This also adds a stub for register_page_bootmem_memmap to allow ppc to build
with sparse vmemmap defined. Leaving this as a stub is fine since the same
vmemmap addresses are also handled in vmemmap_populate and as such are
properly mapped.
David Herrmann [Wed, 2 Oct 2013 14:41:04 +0000 (16:41 +0200)]
x86/simplefb: Mark framebuffer mem-resources as IORESOURCE_BUSY to avoid bootup warning
IORESOURCE_BUSY is used to mark temporary driver mem-resources
instead of global regions. This suppresses warnings if regions
overlap with a region marked as BUSY.
This was always the case for VESA/VGA/EFI framebuffer regions so
do the same for simplefb regions. The reason we do this is to
allow device handover to real GPU drivers like
i915/radeon/nouveau which get the same regions via PCI BARs.
Maybe at some point we will be able to unregister platform
devices properly during the handover. In this case the simplefb
region would get removed before the new region is created.
However, this is currently not the case and would require rather
huge changes in remove_conflicting_framebuffers(). Add the BUSY
marker now and try to eventually rewrite the handover for a next release.
Also see kernel/resource.c for more information:
/*
* if a resource is "BUSY", it's not a hardware resource
* but a driver mapping of such a resource; we don't want
* to warn for those; some drivers legitimately map only
* partial hardware resources. (example: vesafb)
*/
This suppresses warnings like:
------------[ cut here ]------------
WARNING: CPU: 2 PID: 199 at arch/x86/mm/ioremap.c:171 __ioremap_caller+0x2e3/0x390()
Info: mapping multiple BARs. Your kernel is fine.
Call Trace:
dump_stack+0x54/0x8d
warn_slowpath_common+0x7d/0xa0
warn_slowpath_fmt+0x4c/0x50
iomem_map_sanity_check+0xac/0xe0
__ioremap_caller+0x2e3/0x390
ioremap_wc+0x32/0x40
i915_driver_load+0x670/0xf50 [i915]
...
Linus Torvalds [Thu, 3 Oct 2013 04:48:32 +0000 (21:48 -0700)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We have a fairly large batch of fixes this time around, mostly just
due to various platforms all having a fix or two more than usual.
Worth pointing out are:
- A fix for EDMA on Davinci/OMAP where channel allocation broke with
the DT conversion. Due to some miscommunication we didn't
understand the impact of the breakage, so we were pushing back on
it for 3.12, but it sounds like it's actually breaking quite a few
people out there.
- A bunch of fixes for Marvell platforms, some straggling fixes for
merge window fallout and some fixes for a couple of the platforms
(Netgear RN102 in particular).
- A fix for a race between multi-cluster power management and cpu
hotplug on Versatile Express.
And a bunch of other smaller fixes that all add up.
We'll be switching over into stricter regressions-only mode from here
on out"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
ARM: multi_v7_defconfig: add SDHCI for i.MX
bus: mvebu-mbus: Fix optional pcie-mem/io-aperture properties
ARM: mvebu: add missing DT Mbus ranges and relocate PCIe DT nodes for RN102
ARM: at91: sam9g45: shutdown ddr1 too when rebooting
MAINTAINERS: ARM: SIRF: use kernel.org mail box
MAINTAINERS: ARM: SIRF: add missed drivers into maintain list
ARM: edma: Fix clearing of unused list for DT DMA resources
ARM: vexpress: tc2: fix hotplug/idle/kexec race on cluster power down
ARM: dts: sirf: fix interrupt and dma prop of VIP for prima2 and atlas6
ARM: dts: sirf: fix the ranges of peri-iobrg of prima2
ARM: dts: makefile: build atlas6-evb.dtb for ARCH_ATLAS6
ARM: dts: sirf: fix fifosize, clks, dma channels for UART
ARM: mvebu: Add DT entry for ReadyNAS 102 to use gpio-poweroff driver
ARM: mvebu: fix ReadyNAS 102 Power button GPIO to make it active high
ARM: mach-integrator: Add stub for pci_v3_early_init() for !CONFIG_PCI
ARM: shmobile: Remove #gpio-ranges-cells DT property
gpio: rcar: Remove #gpio-range-cells DT property usage
ARM: shmobile: armadillo: fixup ether pinctrl naming
ARM: shmobile: Lager: add Micrel KSZ8041 PHY fixup
ARM: shmobile: update SDHI DT compatibility string to the <unit>-<soc> format
...
Previously, when a signal was registered with SA_SIGINFO, parameters 2
and 3 of the signal handler were written to registers r1 and r2 before
the register set was saved. This led to corruption of these two
registers after returning from the signal handler (the wrong values were
restored).
With this patch, registers are now saved before any parameters are
passed, thus maintaining the processor state from before signal entry.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Olof Johansson [Thu, 3 Oct 2013 03:55:05 +0000 (20:55 -0700)]
Merge tag 'fixes-3.12-2' of git://git.infradead.org/linux-mvebu into fixes
From Jason Cooper:
mvebu fixes for v3.12 (round 2)
- mvebu
- fix ReadyNAS 102 power button (needs to be active high)
- fix ReadyNAS 102 automated rebooting (prevent hang) by add gpio-poweroff
node
- fix booting ReadyNAS 102 by adding MBus ranges and PCIe DT nodes
- mvebu-mbus: prevent PCIe driver from continuing with corrupted resource
* tag 'fixes-3.12-2' of git://git.infradead.org/linux-mvebu:
bus: mvebu-mbus: Fix optional pcie-mem/io-aperture properties
ARM: mvebu: add missing DT Mbus ranges and relocate PCIe DT nodes for RN102
ARM: mvebu: Add DT entry for ReadyNAS 102 to use gpio-poweroff driver
ARM: mvebu: fix ReadyNAS 102 Power button GPIO to make it active high
Thomas Petazzoni [Wed, 11 Sep 2013 10:32:05 +0000 (12:32 +0200)]
sparc: fix MSI build failure on Sparc32
Commit ebd97be635 ('PCI: remove ARCH_SUPPORTS_MSI kconfig option')
removes the ARCH_SUPPORTS_MSI Kconfig option that allowed
architectures to indicate whether they support PCI MSI or not. Now,
PCI MSI support can be compiled in on any architecture thanks to the
use of weak functions thanks to 4287d824f265 ('PCI: use weak functions
for MSI arch-specific functions').
So, architecture specific code is now responsible to ensure that its
PCI MSI code builds in all cases, or be appropriately conditionally
compiled.
On Sparc, the MSI support is only provided for Sparc64, so the
ARCH_SUPPORTS_MSI kconfig option was only selected for SPARC64, and
not for the Sparc architecture as a whole. Therefore, removing
ARCH_SUPPORTS_MSI broke Sparc32 configurations with CONFIG_PCI_MSI=y,
because the Sparc-specific MSI code is not designed to be built on
Sparc32.
To solve this, this commit ensures that the Sparc MSI code is only
built on Sparc64. This is done thanks to a new Kconfig Makefile helper
option SPARC64_PCI_MSI, modeled after the existing SPARC64_PCI. The
SPARC64_PCI_MSI option is an hidden option that is true when both
Sparc64 PCI support is enabled and MSI is enabled. The
arch/sparc/kernel/pci_msi.c file is now only built when
SPARC64_PCI_MSI is true.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reported-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David Miller [Wed, 2 Oct 2013 18:25:09 +0000 (14:25 -0400)]
mm: Fix generic hugetlb pte check return type.
The include/asm-generic/hugetlb.h stubs that just vector huge_pte_*()
calls to the pte_*() implementations won't work in certain situations.
x86 and sparc, for example, return "unsigned long" from the bit
checks, and just go "return pte_val(pte) & PTE_BIT_FOO;"
But since huge_pte_*() returns 'int', if any high bits on 64-bit are
relevant, they get chopped off.
The net effect is that we can loop forever trying to COW a huge page,
because the huge_pte_write() check signals false all the time.
Reported-by: Gurudas Pai <gurudas.pai@oracle.com> Tested-by: Gurudas Pai <gurudas.pai@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: David Rientjes <rientjes@google.com>
Kees Cook [Wed, 2 Oct 2013 05:13:34 +0000 (22:13 -0700)]
sparc: fix ldom_reboot buffer overflow harder
The length argument to strlcpy was still wrong. It could overflow the end of
full_boot_str by 5 bytes. Instead of strcat and strlcpy, just use snprint.
Reported-by: Brad Spengler <spender@grsecurity.net> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 2 Oct 2013 16:36:10 +0000 (09:36 -0700)]
Merge tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"All small, mostly driver-specific fixes: a few ASoC driver fixes
(trivial stable fixes, sgtl5000 fixes), one DPCM fix, an old AC97 ID,
and a fix for HD-audio Conexant GPIO"
* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix GPIO for Acer Aspire 3830TG
ALSA: ac97: Add ID for TI TLV320AIC27 codec
ASoC: imx-sgtl5000: Fix uninitialized pointer use in error path
ASoC: imx-sgtl5000: do not use devres on a foreign device
ASoC: blackfin: Add missing break statement to bf6xx
ASoC: 88pm860x: array overflow in snd_soc_put_volsw_2r_st()
ASoC: ab8500-codec: info leak in anc_status_control_put()
ASoC: max98095: a couple array underflows
ASoC: core: Only add platform DAI widgets once.
Linus Torvalds [Wed, 2 Oct 2013 16:34:47 +0000 (09:34 -0700)]
Merge tag 'pinctrl-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Various build warning fixes.
- Correct the S5P pin count.
- Handle BIAS_DEFAULT properly in the Palmas driver.
* tag 'pinctrl-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: palmas: do not abort pin configuration for BIAS_DEFAULT
pinctrl: Correct number of pins for s5pv210
pinctrl: remove an unnecessary cast
pinctrl: fix pinconf_dbg_config_write return type
pinctrl: tegra114: Remove MODULE_ALIAS
* pm-fixes:
intel_pstate: fix no_turbo
cpufreq: cpufreq-cpu0: NULL is a valid regulator, part 2
cpufreq: SPEAr: Fix incorrect variable type
PM / hibernate: Fix user space driven resume regression
target: Fall back to vzalloc upon ->sess_cmd_map kzalloc failure
This patch changes transport_alloc_session_tags() to fall back to
use vzalloc when kzalloc fails for big tag_num that end up generating
larger order allocations.
Also use is_vmalloc_addr() in transport_alloc_session_tags() failure
path, and normal transport_free_session() path to determine when
vfree() needs to be called instead of kfree().
v2 changes:
- Use __GFP_NOWARN | __GFP_REPEAT for sess_cmd_map kzalloc (mst)
Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Asias He <asias@redhat.com> Cc: Kent Overstreet <kmo@daterainc.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
vhost/scsi: Use GFP_ATOMIC with percpu_ida_alloc for obtaining tag
Fix GFP_KERNEL -> GFP_ATOMIC usage of percpu_ida_alloc() within
vhost_scsi_get_tag(), as this code is expected to be called directly
from interrupt context.
v2 changes:
- Handle possible tag < 0 failure with GFP_ATOMIC
Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Asias He <asias@redhat.com> Cc: Kent Overstreet <kmo@daterainc.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug where ib_destroy_cm_id() was incorrectly being called
after srpt_destroy_ch_ib() had destroyed the active QP.
This would result in the following failed SRP_LOGIN_REQ messages:
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff1762bd, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 1 (guid=0xfe80000000000000:0x2c903009f8f41)
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff1758f9, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 2 (guid=0xfe80000000000000:0x2c903009f8f42)
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff175941, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 2 (guid=0xfe80000000000000:0x2c90300a3cfb2)
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff176299, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 1 (guid=0xfe80000000000000:0x2c90300a3cfb1)
mlx4_core 0000:84:00.0: command 0x19 failed: fw status = 0x9
rejected SRP_LOGIN_REQ because creating a new RDMA channel failed.
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff176299, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 1 (guid=0xfe80000000000000:0x2c90300a3cfb1)
mlx4_core 0000:84:00.0: command 0x19 failed: fw status = 0x9
rejected SRP_LOGIN_REQ because creating a new RDMA channel failed.
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff176299, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 1 (guid=0xfe80000000000000:0x2c90300a3cfb1)
Merge tag 'fixes-for-v3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.12-rc4
Here are some more fixes to musb's OTG support and a regression
caused on latest merge window; pxa25x_udc and gpio-vbus learned
to cope with deferred probe; s3c-hsotg got a fix for non-periodic
endpoints write size and f_fs got an error handling fix for cases
where ffs_do_descs() fail.
ACPI: Use EXPORT_SYMBOL() for acpi_bus_get_device()
Commit caf5c03f (ACPI: Move acpi_bus_get_device() from bus.c to
scan.c) caused acpi_bus_get_device() to be exported using
EXPORT_SYMBOL_GPL(), but that broke some binary drivers in
existence, so revert that change.
Reported-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When sysfs for no_turbo is set, then also some p states in turbo regions
are observed. This patch will set IDA Engage bit when no_turbo is set to
explicitly disengage turbo.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
1) Multiply in netfilter IPVS can overflow when calculating destination
weight. From Simon Kirby.
2) Use after free fixes in IPVS from Julian Anastasov.
3) SFC driver bug fixes from Daniel Pieczko.
4) Memory leak in pcan_usb_core failure paths, from Alexey Khoroshilov.
5) Locking and encapsulation fixes to serial line CAN driver, from
Andrew Naujoks.
6) Duplex and VF handling fixes to bnx2x driver from Yaniv Rosner,
Eilon Greenstein, and Ariel Elior.
7) In lapb, if no other packets are outstanding, T1 timeouts actually
stall things and no packet gets sent. Fix from Josselin Costanzi.
8) ICMP redirects should not make it to the socket error queues, from
Duan Jiong.
9) Fix bugs in skge DMA mapping error handling, from Nikulas Patocka.
10) Fix setting of VLAN priority field on via-rhine driver, from Roget
Luethi.
11) Fix TX stalls and VLAN promisc programming in be2net driver from
Ajit Khaparde.
12) Packet padding doesn't get handled correctly in new usbnet SG
support code, from Ming Lei.
13) Fix races in netdevice teardown wrt. network namespace closing.
From Eric W. Biederman.
14) Fix potential missed initialization of net_secret if not TCP
connections are openned. From Eric Dumazet.
15) Cinterion PLXX product ID in qmi_wwan driver is wrong, from
Aleksander Morgado.
16) skb_cow_head() can change skb->data and thus packet header pointers,
don't use stale ip_hdr reference in ip_tunnel code.
17) Backend state transition handling fixes in xen-netback, from Paul
Durrant.
18) Packet offset for AH protocol is handled wrong in flow dissector,
from Eric Dumazet.
19) Taking down an fq packet scheduler instance can leave stale packets
in the queues, fix from Eric Dumazet.
20) Fix performance regressions introduced by TCP Small Queues. From
Eric Dumazet.
21) IPV6 GRE tunneling code calculates max_headroom incorrectly, from
Hannes Frederic Sowa.
22) Multicast timer handlers in ipv4 and ipv6 can be the last and final
reference to the ipv4/ipv6 specific network device state, so use the
reference put that will check and release the object if the
reference hits zero. From Salam Noureddine.
23) Fix memory corruption in ip_tunnel driver, and use skb_push()
instead of __skb_push() so that similar bugs are less hard to find.
From Steffen Klassert.
24) Add forgotten hookup of rtnl_ops in SIT and ip6tnl drivers, from
Nicolas Dichtel.
25) fq scheduler doesn't accurately rate limit in certain circumstances,
from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (103 commits)
pkt_sched: fq: rate limiting improvements
ip6tnl: allow to use rtnl ops on fb tunnel
sit: allow to use rtnl ops on fb tunnel
ip_tunnel: Remove double unregister of the fallback device
ip_tunnel_core: Change __skb_push back to skb_push
ip_tunnel: Add fallback tunnels to the hash lists
ip_tunnel: Fix a memory corruption in ip_tunnel_xmit
qlcnic: Fix SR-IOV configuration
ll_temac: Reset dma descriptors indexes on ndo_open
skbuff: size of hole is wrong in a comment
ipv6 mcast: use in6_dev_put in timer handlers instead of __in6_dev_put
ipv4 igmp: use in_dev_put in timer handlers instead of __in_dev_put
ethernet: moxa: fix incorrect placement of __initdata tag
ipv6: gre: correct calculation of max_headroom
powerpc/83xx: gianfar_ptp: select 1588 clock source through dts file
Revert "powerpc/83xx: gianfar_ptp: select 1588 clock source through dts file"
bonding: Fix broken promiscuity reference counting issue
tcp: TSQ can use a dynamic limit
dm9601: fix IFF_ALLMULTI handling
pkt_sched: fq: qdisc dismantle fixes
...
Linus Torvalds [Tue, 1 Oct 2013 17:28:11 +0000 (10:28 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs lru leak fix from Al Viro:
"The fix in "super: fix for destroy lrus" didn't - they need to be
destroyed, all right, but that's the wrong place..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs/super.c: fix lru_list leak for real
Linus Torvalds [Tue, 1 Oct 2013 17:25:10 +0000 (10:25 -0700)]
Merge git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull two KVM fixes from Gleb Natapov.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: do not check bit 12 of EPT violation exit qualification when undefined
ARM: kvm: rename cpu_reset to avoid name clash
Al Viro [Tue, 1 Oct 2013 17:11:21 +0000 (13:11 -0400)]
fs/super.c: fix lru_list leak for real
Freeing ->s_{inode,dentry}_lru in deactivate_locked_super() is wrong;
the right place is destroy_super(). As it is, we leak them if sget()
decides that new superblock it has allocated (and never shown to
anybody) isn't needed and should be freed.
If the property was not specified then the returned resource had a
resource_size(..) == 1, rather than 0. The PCI-E driver checks for 0 so it
blindly continues on with a corrupted resource.
The regression was introduced into v3.12 by:
11be654 PCI: mvebu: Adapt to the new device tree layout
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Eric Dumazet [Tue, 1 Oct 2013 16:10:16 +0000 (09:10 -0700)]
pkt_sched: fq: rate limiting improvements
FQ rate limiting suffers from two problems, reported
by Steinar :
1) FQ enforces a delay when flow quantum is exhausted in order
to reduce cpu overhead. But if packets are small, current
delay computation is slightly wrong, and observed rates can
be too high.
Steinar had this problem because he disabled TSO and GSO,
and default FQ quantum is 2*1514.
(Of course, I wish recent TSO auto sizing changes will help
to not having to disable TSO in the first place)
2) maxrate was not used for forwarded flows (skbs not attached
to a socket)
Reported-by: Steinar H. Gunderson <sesse@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-kernels.git / log