The register for 0xe420 is unable to hold any value, including
this bit. The documentation is also mixed between having a
register bit for toggle and having a state command setup
for it. Apparently the register toggle is deprecated.
Remove the register toggle as evidence shows it's futile.
The thing remaining is an apology and humble request for
Mesa folks to resurrect their state setup for this as they
were on right track from start.
Chris Wilson [Tue, 31 Jul 2018 13:26:29 +0000 (14:26 +0100)]
drm/i915: Interactive RPS mode
RPS provides a feedback loop where we use the load during the previous
evaluation interval to decide whether to up or down clock the GPU
frequency. Our responsiveness is split into 3 regimes, a high and low
plateau with the intent to keep the gpu clocked high to cover occasional
stalls under high load, and low despite occasional glitches under steady
low load, and inbetween. However, we run into situations like kodi where
we want to stay at low power (video decoding is done efficiently
inside the fixed function HW and doesn't need high clocks even for high
bitrate streams), but just occasionally the pipeline is more complex
than a video decode and we need a smidgen of extra GPU power to present
on time. In the high power regime, we sample at sub frame intervals with
a bias to upclocking, and conversely at low power we sample over a few
frames worth to provide what we consider to be the right levels of
responsiveness respectively. At low power, we more or less expect to be
kicked out to high power at the start of a busy sequence by waitboosting.
Prior to commit e9af4ea2b9e7 ("drm/i915: Avoid waitboosting on the active
request") whenever we missed the frame or stalled, we would immediate go
full throttle and upclock the GPU to max. But in commit e9af4ea2b9e7, we
relaxed the waitboosting to only apply if the pipeline was deep to avoid
over-committing resources for a near miss. Sadly though, a near miss is
still a miss, and perceptible as jitter in the frame delivery.
To try and prevent the near miss before having to resort to boosting
after the fact, we use the pageflip queue as an indication that we are
in an "interactive" regime and so should sample the load more frequently
to provide power before the frame misses it vblank. This will make us
more favorable to providing a small power increase (one or two bins) as
required rather than going all the way to maximum and then having to
work back down again. (We still keep the waitboosting mechanism around
just in case a dramatic change in system load requires urgent uplocking,
faster than we can provide in a few evaluation intervals.)
v2: Reduce rps_set_interactive to a boolean parameter to avoid the
confusion of what if they wanted a new power mode after pinning to a
different mode (which to choose?)
v3: Only reprogram RPS while the GT is awake, it will be set when we
wake the GT, and while off warns about being used outside of rpm.
v4: Fix deferred application of interactive mode
v5: s/state/interactive/
v6: Group the mutex with its principle in a substruct
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107111 Fixes: e9af4ea2b9e7 ("drm/i915: Avoid waitboosting on the active request") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180731132629.3381-1-chris@chris-wilson.co.uk
(cherry picked from commit 60548c554be2830d29d2533dad0ac8133347ee51) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
First of all don't try to read dpcd if PSR is not even supported.
But also, if read failed return -EIO instead of reporting via a
backchannel.
v2: fix dev_priv: At this level m->private is the connector. (CI/DK)
don't convert dpcd read errors to EIO. (DK)
Fixes: 5b7b30864d1d ("drm/i915/psr: Split sink status into a separate debugfs node") Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Cc: José Roberto de Souza <jose.souza@intel.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180720003155.16290-1-rodrigo.vivi@intel.com
(cherry picked from commit 7a72c78bdd0a1ea1d879610542679cc680398220) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Dave Airlie [Tue, 31 Jul 2018 23:02:12 +0000 (09:02 +1000)]
Merge branch 'drm-armada-devel' of git://git.armlinux.org.uk/~rmk/linux-arm into drm-next
This set of changes migrates Armada DRM from legacy modeset to atomic
modeset. This is everything from the "Transition Armada DRM planes to
atomic state" and "Finish Armada DRM transition to atomic modeset"
patch sets as posted on drm-devel, excluding the "Finish Armada DRM DT
support" series.
These series did not evoke any comments - if there are any, these can
be addressed via follow up patches.
Developed and tested on Dove Cubox with xf86-video-armada including the
overlay plane, and also tested with the tools in libdrm.
Dave Airlie [Tue, 31 Jul 2018 22:52:15 +0000 (08:52 +1000)]
Merge tag 'drm-msm-next-2018-07-30' of git://people.freedesktop.org/~robclark/linux into drm-next
A bit larger this time around, due to introduction of "dpu1" support
for the display controller in sdm845 and beyond. This has been on
list and undergoing refactoring since Feb (going from ~110kloc to
~30kloc), and all my review complaints have been addressed, so I'd be
happy to see this upstream so further feature work can procede on top
of upstream.
Also includes the gpu coredump support, which should be useful for
debugging gpu crashes. And various other misc fixes and such.
Mikulas Patocka [Sun, 3 Jun 2018 14:41:03 +0000 (16:41 +0200)]
udl-kms: dont spam the syslog with debug messages
The udl kms driver writes messages to the syslog whenever some application
opens or closes /dev/fb0 and whenever the user switches between the
Xserver and the console.
This patch changes the priority of these messages to debug.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Mikulas Patocka [Sun, 3 Jun 2018 14:41:02 +0000 (16:41 +0200)]
udl-kms: use spin_lock_irq instead of spin_lock_irqsave
spin_lock_irqsave and spin_unlock_irqrestore is inteded to be called from
a context where it is unknown if interrupts are enabled or disabled (such
as interrupt handlers). From a process context, we should call
spin_lock_irq and spin_unlock_irq, that avoids the costly pushf and popf
instructions.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Mikulas Patocka [Sun, 3 Jun 2018 14:41:00 +0000 (16:41 +0200)]
udl-kms: avoid division
Division is slow, so it shouldn't be done by the pixel generating code.
The driver supports only 2 or 4 bytes per pixel, so we can replace
division with a shift.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Mikulas Patocka [Sun, 3 Jun 2018 14:40:56 +0000 (16:40 +0200)]
udl-kms: handle allocation failure
Allocations larger than PAGE_ALLOC_COSTLY_ORDER are unreliable and they
may fail anytime. This patch fixes the udl kms driver so that when a large
alloactions fails, it tries to do multiple smaller allocations.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Mikulas Patocka [Sun, 3 Jun 2018 14:40:55 +0000 (16:40 +0200)]
udl-kms: change down_interruptible to down
If we leave urbs around, it causes not only leak, but also memory
corruption. This patch fixes the function udl_free_urb_list, so that it
always waits for all urbs that are in progress.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
dt-bindings: msm/disp: Add bindings for Snapdragon 845 DPU
Adds bindings for Snapdragon 845 display processing unit
Changes in v2:
- Use SoC specific compatibles for mdss and dpu (Rob Herring)
- Use assigned-clocks to set initial clock frequency (Rob Herring)
Changes in v3 (all suggested by Rob Herring):
- Rename mdss_phys to mdss
- Correct description for clocks/assigned-clocks
- Rename mdp_phys to mdp
- Rename vbif_phys to vbif
- Remove redundant interrupt-parent from mdss_mdp
- Fully specify 'ranges' and use relative reg address in mdss_mdp
Cc: Rob Herring <robh+dt@kernel.org> Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org> Signed-off-by: Rajesh Yadav <ryadav@codeaurora.org> Signed-off-by: Sean Paul <seanpaul@chromium.org> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Rob Clark <robdclark@gmail.com>
dt-bindings: msm/dsi: Add mdp transfer time to msm dsi binding
Adds mdp transfer time to msm dsi binding
Changes in v3:
- Added Rob's R-b
Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org> Signed-off-by: Rajesh Yadav <ryadav@codeaurora.org> Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Rob Clark <robdclark@gmail.com>
The suspend/resume functions are not referenced when power
management is disabled:
drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c:1288:12: error: 'dpu_runtime_resume' defined but not used [-Werror=unused-function]
drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c:1261:12: error: 'dpu_runtime_suspend' defined but not used [-Werror=unused-function]
This marks them as __maybe_unused to let the compiler
drop the functions without complaining.
Fixes: 591225291ca2 ("drm/msm: Add SDM845 DPU support") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Rob Clark <robdclark@gmail.com>
All users of do_gettimeofday() have been removed, but this one recently
crept in, along with an incorrect printing of the microseconds portion.
This converts it to using ktime_get_real_timespec64() as a direct
replacement, and adds the leading zeroes. I considered using monotonic
times (ktime_get()) instead, but as this timestamp appears to only
be used for humans rather than compared with other timestamps, the
real time domain is probably good enough.
Fixes: e43b045e2c82 ("drm/msm/gpu: Capture the state of the GPU") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Rob Clark <robdclark@gmail.com>
Sean Paul [Wed, 25 Jul 2018 20:34:45 +0000 (16:34 -0400)]
drm/msm: dsi: Handle dual-channel for 6G as well
This fixes up a collision between introducing dual-channel support and
the dsi refactors. This patch applies the same dual-channel
considerations and pclk calculations to both v2 and 6G, with a bit of
abstracting for good measure.
Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Rob Clark <robdclark@gmail.com>
Jordan Crouse [Tue, 24 Jul 2018 16:33:30 +0000 (10:33 -0600)]
drm/msm/adreno: Add a5xx specific registers for the GPU state
HLSQ, SP and TP registers are only accessible from a special
aperture and to make matters worse the aperture is blocked from
the CPU on targets that can support secure rendering. Luckily the
GPU hardware has its own purpose built register dumper that can
access the registers from the aperture. Add a5xx specific code
to program the crashdumper and retrieve the wayward registers
and dump them for the crash state.
Also, remove a block of registers the regular CPU accessible
list that aren't useful for debug which helps reduce the size
of the crash state file by a goodly amount.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@gmail.com>
Jordan Crouse [Tue, 24 Jul 2018 16:33:29 +0000 (10:33 -0600)]
drm/msm/adreno: Add ringbuffer data to the GPU state
Add the contents of each ringbuffer to the GPU state and dump the
data in the crash file encoded with ascii85. To save space only
the used portions of the ringbuffer are dumped.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@gmail.com>
Jordan Crouse [Tue, 24 Jul 2018 16:33:28 +0000 (10:33 -0600)]
drm/msm/adreno: Convert the show/crash file format
Convert the format of the 'show' debugfs file and the crash
dump to a format resembling YAML. This should be easier to
parse and be more flexible for future changes and expansions.
v2: Use a standard .rst for the msm crashdump documentation
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@gmail.com>
Jordan Crouse [Tue, 24 Jul 2018 16:33:27 +0000 (10:33 -0600)]
drm/msm/gpu: Capture the GPU state on a GPU hang
Capture the GPU state on a GPU hang and store it for later playback
via the devcoredump facility. Only one crash state is stored at a
time on the assumption that the first hang is usually the most
interesting. The existing crash state can be cleared after capturing
it and then a new one will be captured on the next hang.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@gmail.com>
Jordan Crouse [Tue, 24 Jul 2018 16:33:25 +0000 (10:33 -0600)]
drm/msm/gpu: Convert the GPU show function to use the GPU state
Convert the existing GPU show function to use the GPU state to
dump the information rather than reading it directly from the hardware.
This will require an additional step to capture the state before
dumping it for the existing nodes but it will greatly facilitate reusing
the same code for dumping a previously captured state from a GPU hang.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@gmail.com>
Jordan Crouse [Tue, 24 Jul 2018 16:33:24 +0000 (10:33 -0600)]
drm/msm/gpu: Capture the state of the GPU
Add the infrastructure to capture the current state of the GPU and
store it in memory so that it can be dumped later.
For now grab the same basic ringbuffer information and registers
that are provided by the debugfs 'gpu' node but obviously this should
be extended to capture a much larger set of GPU information.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@gmail.com>
Jordan Crouse [Tue, 24 Jul 2018 16:33:23 +0000 (10:33 -0600)]
drm: Add puts callback for the coredump printer
Add a puts function for the coredump printer to bypass printf()
for constant strings for a speed boost. Reorganize the
coredump printf callback to share as much code as possible.
v2: Try to reuse code between print and puts as suggested by
Chris Wilson
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@gmail.com>
Jordan Crouse [Tue, 24 Jul 2018 16:33:22 +0000 (10:33 -0600)]
drm: Add a -puts() function for the seq_file printer
Add a puts() function to use seq_puts() to help speed up
up print time for constant strings.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@gmail.com>
Jordan Crouse [Tue, 24 Jul 2018 16:33:21 +0000 (10:33 -0600)]
drm: Add drm_puts() to complement drm_printf()
Add drm_puts() for a much faster path to print constant strings
into a drm_printer object with memcpy and friends. This can
have seconds off of really large outputs such as GPU dumps.
If the drm_printer object supports a custom puts function then
use that otherwise fall back to the slower legacy printf call.
v2: Add documentation for drm_puts() per Daniel Vetter
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
[robclark fix minor htmldocs warning] Signed-off-by: Rob Clark <robdclark@gmail.com>
Jordan Crouse [Tue, 24 Jul 2018 16:33:20 +0000 (10:33 -0600)]
drm: drm_printer: Add printer for devcoredump
Add a drm printer suitable for use with the read callback for
devcoredump or other suitable buffer based output format that
isn't otherwise covered by seq_file.
v2: Add improved documentation per Daniel Vetter
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@gmail.com>
Jordan Crouse [Tue, 24 Jul 2018 16:33:19 +0000 (10:33 -0600)]
include: Move ascii85 functions from i915 to linux/ascii85.h
The i915 DRM driver very cleverly used ascii85 encoding for their
GPU state file. Move the encode functions to a general header file to
support other drivers that might be interested in the same
functionality.
v4: Make the return value const char * as suggested by Chris Wilson
v3: Fix error_puts -> err_puts pointed out by the 01.org bot
v2: Update API to be cleaner for the caller as suggested by Chris Wilson
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@gmail.com>
Russell King [Mon, 30 Jul 2018 10:53:06 +0000 (11:53 +0100)]
drm/armada: update primary framebuffer parameters on mode change
The framebuffer base address and toggling mode needs to be updated
when the interlaced flag for mode changes is updated. Arrange to
reprogram these parameters when only the mode has changed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:53:06 +0000 (11:53 +0100)]
drm/armada: update planes after the dumb frame is complete
Write out the plane updates after the dumb frame has completed, but
just before the blank period. This allows all the plane updates to
be performed in a flicker-free non-tearing manner.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:53:06 +0000 (11:53 +0100)]
drm/armada: switch overlay plane to atomic modeset
Switch the overlay plane away from the transitional helpers and legacy
methods, and use atomic helpers instead to implement the legacy
set_plane ioctl methods.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:53:06 +0000 (11:53 +0100)]
drm/armada: switch primary plane to atomic modeset
Switch the primary plane away from the transitional helpers, and
use the atomic helpers instead to implement the legacy set_plane
ioctl call for this plane.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:53:06 +0000 (11:53 +0100)]
drm/armada: switch legacy modeset to atomic modeset
Switch the legacy set_config() method to use the atomic modeset
helper, which allows us to get rid of the legacy dpms, prepare,
commit, mode_set, mode_set_base and disable helper methods.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Implement the atomic_enable()/atomic_disable() methods used by the
atomic modeset helpers. atomic_disable() will need some transitional
code during conversion to ensure proper ordering is maintained.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:52:34 +0000 (11:52 +0100)]
drm/armada: unhook dpms state from armada_drm_crtc_update()
Explicitly pass in the desired enable/disable state into
armada_drm_crtc_update() rather than having it use the DPMS state
stored in our crtc structure.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:52:34 +0000 (11:52 +0100)]
drm/armada: handle atomic modeset crtc events
Prepare handling for atomic modeset CRTC events. Currently, using the
transition helpers, CRTC events do not exist, but once we switch to
proper atomic modeset, they have to be handled.
We queue an event for the next vblank in two places:
- armada_drm_crtc_atomic_flush() provided we aren't doing an
atomic modeset.
- armada_drm_crtc_commit() if we are committing a modeset.
This ensures that the event is sent at the correct time (after all
updates have been written to the hardware and after the following
vblank.)
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:52:34 +0000 (11:52 +0100)]
drm/armada: update debug in armada_drm_crtc_mode_set_nofb()
Update debug to use KMS level, and print the mode using the standard
format for mode lines, but print the adjusted CRTC parameters as
that's what we will be programming for.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:52:34 +0000 (11:52 +0100)]
drm/armada: move sync signal polarity to mode_set_nofb() method
For atomic modeset, we need to set the sync signal polarities from the
CRTC state structure rather than the legacy mode structure stored in
CRTC. In any case, we should update this from our mode_set_nofb()
method, rather than the commit() method. Move it there, and ensure
that armada_drm_crtc_update() will not overwrite these bits.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:52:34 +0000 (11:52 +0100)]
drm/armada: push interlace calculation into armada_drm_plane_calc()
Push the interlaced frame calculation down into armada_drm_plane_calc()
which needs to apply the same correction for both the overlay and
primary planes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:52:34 +0000 (11:52 +0100)]
drm/armada: provide pitches from armada_drm_plane_calc_addrs()
Provide the framebuffer pitches from armada_drm_plane_calc_addrs() as
well as the base addresses for each plane. Since this is now about
more than just addresses, rename to armada_drm_plane_calc().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:52:34 +0000 (11:52 +0100)]
drm/armada: pass plane state into armada_drm_plane_calc_addrs()
armada_drm_plane_calc_addrs() gets all its information from the plane
state, so it makes sense to pass the plane state pointer down into this
function, rather than extracting the information in identical ways,
sometimes a couple of layers up.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:52:34 +0000 (11:52 +0100)]
drm/armada: move armada_drm_mode_config_funcs to armada_drv.c
Move the armada_drm_mode_config_funcs to armada_drv.c, since this now
has less to do with FBs than it does with general mode configuration.
In doing so, we need to make armada_fb_create() visible to armada_drv.c,
which reveals a function name clash with armada_fbdev.c. Rename the
version in armada_fbdev.c.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:52:34 +0000 (11:52 +0100)]
drm/armada: add plane colorspace properties
Use the DRM standard plane properties for specifying the YUV
colour encoding parameter. Our colour range is fixed at limited
range.
Since we are transitioning to atomic modeset, we need to explicitly
add handling of these properties to our atomic_set_property() method,
but once the transition is complete, these will be removed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Remove the unused CRTC colourspace properties - userspace does not make
use of these. In any case, these are not a property of the CRTC, since
they demonstrably only affect the video (overlay) plane, irrespective
of the format of the graphics (primary) plane.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:52:34 +0000 (11:52 +0100)]
drm/armada: move CBSH properties into overlay plane state
Move the contrast, brightness, and saturation properties to the overlay
plane state structure, and call our overlay commit function to update
the hardware via the planes atomic_update() method.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:52:34 +0000 (11:52 +0100)]
drm/armada: use old_state for update tracking in atomic_update()
Rather than tracking the register state, we can now check the previous
state and decide which registers need updating from that since the old
plane state indicates the previous state which was programmed into the
hardware.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:52:34 +0000 (11:52 +0100)]
drm/armada: remove temporary crtc state
Now that we have the CRTC using the atomic modeset transitional helper,
there is no need to build a temporary crtc state anymore - we can use
the CRTC atomic state directly.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:52:34 +0000 (11:52 +0100)]
drm/armada: convert overlay plane to atomic state
The overlay plane support updates asynchronously to the request, but the
drm_plane_helper_update() transitional helper waits for a vblank event
before releasing the framebuffer. Using the transitional helper would
make the call block, which would introduce a performance regression.
Convert the overlay plane update to use the atomic state structures and
methods for the plane, but implement our own legacy update method
rather than the transitional helper.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:52:34 +0000 (11:52 +0100)]
drm/armada: convert page_flip to use primary plane atomic_update()
page_flip requests happen asynchronously, so we can't wait on the
vblank event before returning to userspace, as the transitional plane
update helper would do. Craft our own implementation that keeps the
asynchronous behaviour of this request, while making use of the atomic
infrastructure for the primary plane update.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:52:34 +0000 (11:52 +0100)]
drm/armada: convert primary plane to atomic state
Convert the primary plane as a whole to use its atomic state and the
transitional helpers. The CRTC is also switched to use the transitional
helpers for mode_set() and mode_set_base().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:52:34 +0000 (11:52 +0100)]
drm/armada: reset all atomic state during driver initialisation
Reset the atomic state of any converted components during driver
initialisation to ensure that we have the atomic state initialised for
any component converted to atomic modeset.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:52:34 +0000 (11:52 +0100)]
drm/armada: use core of primary update_plane for mode set
Use the core of the update_plane method to configure the primary plane
within mode_set() rather than duplicating this code. This moves us
closer to the same code structure that the atomic modeset transitional
helpers will use.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:52:34 +0000 (11:52 +0100)]
drm/armada: move mode set vblank handling and disable/enable
Move the mode set vblank handling and controller enable/disable to the
prepare() and commit() callbacks. This will be needed when we move to
mode_set_nofb() as we should not enable the controller without the
plane coordinates and location having been properly updated.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Russell King [Mon, 30 Jul 2018 10:52:34 +0000 (11:52 +0100)]
drm/armada: clean up armada_drm_crtc_page_flip()
drm_mode_page_flip_ioctl() already takes care of checking the
framebuffer format, and also assigns primary->fb after a successful
call to this handler. These are both redundant, and can be removed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Use new return type vm_fault_t for fault handler in struct
vm_operations_struct. For now, this is just documenting that the
function returns a VM_FAULT value rather than an errno. Once all
instances are converted, vm_fault_t will become a distinct type.
commit 1c8f422059ae ("mm: change return type to vm_fault_t")
Previously vm_insert_pfn() returns err which driver mapped into
VM_FAULT_* type. The new function vmf_insert_pfn() will replace this
inefficiency by returning VM_FAULT_* type.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com> Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
drm/armada: Replace drm_dev_unref with drm_dev_put
This patch unifies the naming of DRM functions for reference counting
of struct drm_device. The resulting code is more aligned with the rest
of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <tdz@users.sourceforge.net> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Dave Airlie [Mon, 30 Jul 2018 00:23:40 +0000 (10:23 +1000)]
Merge tag 'drm-amdkfd-next-2018-07-28' of git://people.freedesktop.org/~gabbayo/linux into drm-next
This is amdkfd pull for 4.19. The major changes are:
- Add Raven support. Raven refers to Ryzen APUs with integrated GFXv9 GPU.
- Integrate GPU reset support
In addition, there are a couple of small fixes and improvements, such as:
- Better handling and reporting to user of VM faults
- Fix race upon context restore
- Allow the user to use specific Compute Units
- Basic power management
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Some miscellaneous ext4 fixes for 4.18; one fix is for a regression
introduced in 4.18-rc4.
Sorry for the late-breaking pull. I was originally going to wait for
the next merge window, but Eric Whitney found a regression introduced
in 4.18-rc4, so I decided to push out the regression plus the other
fixes now. (The other commits have been baking in linux-next since
early July)"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix check to prevent initializing reserved inodes
ext4: check for allocation block validity with block group locked
ext4: fix inline data updates with checksums enabled
ext4: clear mmp sequence number when remounting read-only
ext4: fix false negatives *and* false positives in ext4_check_descriptors()
squashfs: be more careful about metadata corruption
Anatoly Trosinenko reports that a corrupted squashfs image can cause a
kernel oops. It turns out that squashfs can end up being confused about
negative fragment lengths.
The regular squashfs_read_data() does check for negative lengths, but
squashfs_read_metadata() did not, and the fragment size code just
blindly trusted the on-disk value. Fix both the fragment parsing and
the metadata reading code.
ext4: fix check to prevent initializing reserved inodes
Commit 8844618d8aa7: "ext4: only look at the bg_flags field if it is
valid" will complain if block group zero does not have the
EXT4_BG_INODE_ZEROED flag set. Unfortunately, this is not correct,
since a freshly created file system has this flag cleared. It gets
almost immediately after the file system is mounted read-write --- but
the following somewhat unlikely sequence will end up triggering a
false positive report of a corrupted file system:
mkfs.ext4 /dev/vdc
mount -o ro /dev/vdc /vdc
mount -o remount,rw /dev/vdc
Instead, when initializing the inode table for block group zero, test
to make sure that itable_unused count is not too large, since that is
the case that will result in some or all of the reserved inodes
getting cleared.
This fixes the failures reported by Eric Whiteney when running
generic/230 and generic/231 in the the nojournal test case.
Fixes: 8844618d8aa7 ("ext4: only look at the bg_flags field if it is valid") Reported-by: Eric Whitney <enwlinux@gmail.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Merge tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random fixes from Ted Ts'o:
"In reaction to the fixes to address CVE-2018-1108, some Linux
distributions that have certain systemd versions in some cases
combined with patches to libcrypt for FIPS/FEDRAMP compliance, have
led to boot-time stalls for some hardware.
The reaction by some distros and Linux sysadmins has been to install
packages that try to do complicated things with the CPU and hope that
leads to randomness.
To mitigate this, if RDRAND is available, mix it into entropy provided
by userspace. It won't hurt, and it will probably help"
* tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: mix rdrand with entropy sent in from userspace
Merge tag 'gpio-v4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Just a smallish OF fix and a driver fix:
- OF flag fix for special regulator flags
- fix up the Uniphier IRQ callback"
* tag 'gpio-v4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: uniphier: set legitimate irq trigger type in .to_irq hook
gpio: of: Handle fixed regulator flags properly
Merge tag 'mips_fixes_4.18_5' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fix from Paul Burton:
"Here's one more MIPS fix, reverting an errata workaround that was
merged for v4.18-rc2 but has since been found to cause system hangs on
some BCM4718A1-based systems by the OpenWRT project"
* tag 'mips_fixes_4.18_5' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
Revert "MIPS: BCM47XX: Enable 74K Core ExternalSync for PCIe erratum"
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Some driver bugfixes"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: imx: use open drain for recovery GPIO
i2c: rcar: handle RXDMA HW behaviour on Gen3
i2c: imx: Fix reinit_completion() use
i2c: davinci: Avoid zero value of CLKH
Merge tag 'for-linus-20180727' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Bigger than usual at this time, mostly due to the O_DIRECT corruption
issue and the fact that I was on vacation last week. This contains:
- NVMe pull request with two fixes for the FC code, and two target
fixes (Christoph)
- a DIF bio reset iteration fix (Greg Edwards)
- two nbd reply and requeue fixes (Josef)
- SCSI timeout fixup (Keith)
- a small series that fixes an issue with bio_iov_iter_get_pages(),
which ended up causing corruption for larger sized O_DIRECT writes
that ended up racing with buffered writes (Martin Wilck)"
* tag 'for-linus-20180727' of git://git.kernel.dk/linux-block:
block: reset bi_iter.bi_done after splitting bio
block: bio_iov_iter_get_pages: pin more pages for multi-segment IOs
blkdev: __blkdev_direct_IO_simple: fix leak in error case
block: bio_iov_iter_get_pages: fix size of last iovec
nvmet: only check for filebacking on -ENOTBLK
nvmet: fixup crash on NULL device path
scsi: set timed out out mq requests to complete
blk-mq: export setting request completion state
nvme: if_ready checks to fail io to deleting controller
nvmet-fc: fix target sgl list on large transfers
nbd: handle unexpected replies better
nbd: don't requeue the same request twice.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
kvm, mm: account shadow page tables to kmemcg
zswap: re-check zswap_is_full() after do zswap_shrink()
include/linux/eventfd.h: include linux/errno.h
mm: fix vma_is_anonymous() false-positives
mm: use vma_init() to initialize VMAs on stack and data segments
mm: introduce vma_init()
mm: fix exports that inadvertently make put_page() EXPORT_SYMBOL_GPL
ipc/sem.c: prevent queue.status tearing in semop
mm: disallow mappings that conflict for devm_memremap_pages()
kasan: only select SLUB_DEBUG with SYSFS=y
delayacct: fix crash in delayacct_blkio_end() after delayacct init failure
Merge tag 'pci-v4.18-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"Fix a use-after-free error in fatal error recovery (Thomas Tai)"
* tag 'pci-v4.18-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/AER: Work around use-after-free in pcie_do_fatal_recovery()
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Inevitably, after saying that I hoped we would be done on the fixes
front, a couple of issues have cropped up over the last week. Next
time I'll stay schtum.
We've fixed an over-eager BUILD_BUG_ON() which Arnd ran into with
arndconfig, as well as ensuring that KPTI really is disabled on
Thunder-X1, where the cure is worse than the disease (this regressed
when we reworked the heterogeneous CPU feature checking).
Summary:
- Fix disabling of kpti on Thunder-X machines
- Fix premature BUILD_BUG_ON() found with randconfig"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: fix vmemmap BUILD_BUG_ON() triggering on !vmemmap setups
arm64: Check for errata before evaluating cpu features
Revert "MIPS: BCM47XX: Enable 74K Core ExternalSync for PCIe erratum"
This reverts commit 2a027b47dba6 ("MIPS: BCM47XX: Enable 74K Core
ExternalSync for PCIe erratum").
Enabling ExternalSync caused a regression for BCM4718A1 (used e.g. in
Netgear E3000 and ASUS RT-N16): it simply hangs during PCIe
initialization. It's likely that BCM4717A1 is also affected.
I didn't notice that earlier as the only BCM47XX devices with PCIe I
own are:
1) BCM4706 with 2 x 14e4:4331
2) BCM4706 with 14e4:4360 and 14e4:4331
it appears that BCM4706 is unaffected.
While BCM5300X-ES300-RDS.pdf seems to document that erratum and its
workarounds (according to quotes provided by Tokunori) it seems not even
Broadcom follows them.
According to the provided info Broadcom should define CONF7_ES in their
SDK's mipsinc.h and implement workaround in the si_mips_init(). Checking
both didn't reveal such code. It *could* mean Broadcom also had some
problems with the given workaround.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Paul Burton <paul.burton@mips.com> Reported-by: Michael Marley <michael@michaelmarley.com>
Patchwork: https://patchwork.linux-mips.org/patch/20032/
URL: https://bugs.openwrt.org/index.php?do=details&task_id=1688 Cc: Tokunori Ikegami <ikegami@allied-telesis.co.jp> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: James Hogan <jhogan@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org
Merge tag 'drm-fixes-2018-07-27' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Not much happening this week which is good: two imx display fixes and
one i915 quirk addition"
* tag 'drm-fixes-2018-07-27' of git://anongit.freedesktop.org/drm/drm:
drm/i915/glk: Add Quirk for GLK NUC HDMI port issues.
gpu: ipu-csi: Check for field type alternate
drm/imx: imx-ldb: check if channel is enabled before printing warning
drm/imx: imx-ldb: disable LDB on driver bind
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- a couple of new device IDs added to Elan i2c touchpad controller
driver
- another entry in i8042 reset quirk list
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add Lenovo LaVie Z to the i8042 reset list
Input: elan_i2c - add another ACPI ID for Lenovo Ideapad 330-15AST
MAINTAINERS: Add file patterns for serio device tree bindings
Input: elan_i2c - add ACPI ID for lenovo ideapad 330
Merge tag 'trace-v4.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Various fixes to the tracing infrastructure:
- Fix double free when the reg() call fails in
event_trigger_callback()
- Fix anomoly of snapshot causing tracing_on flag to change
- Add selftest to test snapshot and tracing_on affecting each other
- Fix setting of tracepoint flag on error that prevents probes from
being deleted.
- Fix another possible double free that is similar to
event_trigger_callback()
- Quiet a gcc warning of a false positive unused variable
- Fix crash of partial exposed task->comm to trace events"
* tag 'trace-v4.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
kthread, tracing: Don't expose half-written comm when creating kthreads
tracing: Quiet gcc warning about maybe unused link variable
tracing: Fix possible double free in event_enable_trigger_func()
tracing/kprobes: Fix trace_probe flags on enable_trace_kprobe() failure
selftests/ftrace: Add snapshot and tracing_on test case
ring_buffer: tracing: Inherit the tracing setting to next ring buffer
tracing: Fix double free of event_trigger_data
Merge tag 'xfs-4.18-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
- Fix some uninitialized variable errors
- Fix an incorrect check in metadata verifiers
* tag 'xfs-4.18-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: properly handle free inodes in extent hint validators
xfs: Initialize variables in xfs_alloc_get_rec before using them
The size of kvm's shadow page tables corresponds to the size of the
guest virtual machines on the system. Large VMs can spend a significant
amount of memory as shadow page tables which can not be left as system
memory overhead. So, account shadow page tables to the kmemcg.
[shakeelb@google.com: replace (GFP_KERNEL|__GFP_ACCOUNT) with GFP_KERNEL_ACCOUNT] Link: http://lkml.kernel.org/r/20180629140224.205849-1-shakeelb@google.com Link: http://lkml.kernel.org/r/20180627181349.149778-1-shakeelb@google.com Signed-off-by: Shakeel Butt <shakeelb@google.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Greg Thelen <gthelen@google.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Peter Feiner <pfeiner@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / mirror_ubuntu-hirsute-kernel.git / log