Continuing along with the fight against smp_read_barrier_depends() [1]
(or rather, against its improper use), add an unconditional barrier to
cmpxchg. This guarantees that dependency ordering is preserved when a
dependency is headed by an unsuccessful cmpxchg. As it turns out, the
change could enable further simplification of LKMM as proposed in [2].
During driver unload, the driver proceeds with cleanup
without waiting for the scheduled events. So the device
pointers get freed up and driver crashes when the events
are scheduled later.
Flush the bnxt_re_task work queue before starting
device removal.
The ID_AA64DFR0_EL1.PMUVer field doesn't follow the usual ID registers
scheme. While value 0xf indicates a non-architected PMU is implemented,
values 0x1 to 0xe indicate an increasingly featureful architected PMU,
as if the field were unsigned.
For more details, see ARM DDI 0487C.a, D10.1.4, "Alternative ID scheme
used for the Performance Monitors Extension version".
Currently, we treat the field as signed, and erroneously bail out for
values 0x8 to 0xe. Let's correct that.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The plane buffer address/stride/height was incorrectly updated in the
plane_atomic_update operation instead of the vsync irq.
This patch delays this operation in the vsync irq along with the
other plane delayed setup.
This issue was masked using legacy framebuffer and X11 modesetting, but
is clearly visible using gbm rendering when buffer is submitted late after
vblank, like using software decoding and OpenGL rendering in Kodi.
With this patch, tearing and other artifacts disappears completely.
Cc: Michal Lazo <michal.lazo@gmail.com> Fixes: bbbe775ec5b5 ("drm: Add support for Amlogic Meson Graphic Controller") Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/1518689976-23292-1-git-send-email-narmstrong@baylibre.com Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The exynos DRM driver uses real-time 'struct timeval' values
for exporting its timestamps to user space. This has multiple
problems:
1. signed seconds overflow in y2038
2. the 'struct timeval' definition is deprecated in the kernel
3. time may jump or go backwards after a 'settimeofday()' syscall
4. other DRM timestamps are in CLOCK_MONOTONIC domain, so they
can't be compared
5. exporting microseconds requires a division by 1000, which may
be slow on some architectures.
The code existed in two places before, but the IPP portion was
removed in 8ded59413ccc ("drm/exynos: ipp: Remove Exynos DRM
IPP subsystem"), so we no longer need to worry about it.
Ideally timestamps should just use 64-bit nanoseconds instead, but
of course we can't change that now. Instead, this tries to address
the first four points above by using monotonic 'timespec' values.
According to Tobias Jakobi, user space doesn't care about the
timestamp at the moment, so we can change the format. Even if
there is something looking at them, it will work just fine with
monotonic times as long as the application only looks at the
relative values between two events.
In the case of 'recover', an r10bio with R10BIO_WriteError &
R10BIO_IsRecover will be progressed by handle_write_completed().
This function traverses all r10bio->devs[copies].
If devs[m].repl_bio != NULL, it thinks conf->mirrors[dev].replacement
is also not NULL. However, this is not always true.
When there is an rdev of raid10 has replacement, then each r10bio
->devs[m].repl_bio != NULL in conf->r10buf_pool. However, in 'recover',
even if corresponded replacement is NULL, it doesn't clear r10bio
->devs[m].repl_bio, resulting in replacement NULL deference.
This bug was introduced when replacement support for raid10 was
added in Linux 3.3.
As NeilBrown suggested:
Elsewhere the determination of "is this device part of the
resync/recovery" is made by resting bio->bi_end_io.
If this is end_sync_write, then we tried to write here.
If it is NULL, then we didn't try to write.
In case an ADDBA request is received while there is already
an ongoing BA sessions with the same parameters, i.e., update
flow, an ADBBA response with decline status was sent twice. Fix it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Some APs include a non global operating class in their extended channel
switch information element. In such a case, as the operating class is not
known, mac80211 would decide to disconnect.
However the specification states that the operating class needs to be
taken from Annex E, but it does not specify from which table it should be
taken, so it is valid for an AP to use a non global operating class.
To avoid possibly unneeded disconnection, in such a case ignore the
operating class and assume that the current band is used, and if the
resulting channel and band configuration is invalid disconnect.
Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a low level driver calls cfg80211_disconnected(), wep keys are
not cleared. As a result, following connection requests will fail
since cfg80211 internal state shows a connection is still in progress.
Fix this by clearing the wep keys when disconnecting.
This ensures that mac80211 allocated management frames are properly
aligned, which makes copying them more efficient.
For instance, mt76 uses iowrite32_copy to copy beacon frames to beacon
template memory on the chip.
Misaligned 32-bit accesses cause CPU exceptions on MIPS and should be
avoided.
Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When xfrm_policy_get_afinfo returns NULL, it will not hold rcu
read lock. In this case, rcu_read_unlock should not be called
in xfrm_get_tos, just like other places where it's calling
xfrm_policy_get_afinfo.
Internal DASD device driver I/O such as query host access count or
path verification is started using the _sleep_on() function.
To mark a request as started or ended the callback_data is set to either
DASD_SLEEPON_START_TAG or DASD_SLEEPON_END_TAG.
In cases where the request has to be stopped unconditionally the status is
set to DASD_SLEEPON_END_TAG as well which leads to immediate clearing of
the request.
But the request might still be on a device request queue for normal
operation which might lead to a panic because of a BUG() statement in
__dasd_device_process_final_queue() or a list corruption of the device
request queue.
Fix by removing the setting of DASD_SLEEPON_END_TAG in the
dasd_cancel_req() and dasd_generic_requeue_all_requests() functions and
ensure that the request is not deleted in the requeue function.
Trigger the device tasklet in the requeue function and let the normal
processing cleanup the request.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com> Reviewed-by: Jan Hoeppner <hoeppner@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If no metadata devices are configured on raid1/4/5/6/10
(e.g. via dm-raid), md_write_start() unconditionally waits
for superblocks to be written thus deadlocking.
Fix introduces mddev->has_superblocks bool, defines it in md_run()
and checks for it in md_write_start() to conditionally avoid waiting.
Once on it, check for non-existing superblocks in md_super_write().
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198647 Fixes: cc27b0c78c796 ("md: fix deadlock between mddev_suspend() and md_write_start()") Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com> Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Due to a check recently added to copy_to_user(), it's now not permitted to
copy from slab-held data to userspace unless the slab is whitelisted. This
affects rxrpc_recvmsg() when it attempts to place an RXRPC_USER_CALL_ID
control message in the userspace control message buffer. A warning is
generated by usercopy_warn() because the source is the copy of the
user_call_ID retained in the rxrpc_call struct.
Work around the issue by copying the user_call_ID to a variable on the
stack and passing that to put_cmsg().
The tlv_len is u8, so we need to limit the size of the SDP URI. Enforce
this both in the NLA policy and in the code that performs the allocation
and copy, to avoid writing past the end of the allocated buffer.
Fixes: d9b8d8e19b073 ("NFC: llcp: Service Name Lookup netlink interface") Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In AP mode, when a new station associates, rs is initialized immediately
upon association completion, before the phy context is updated with the
association parameters, so the sta bandwidth might be wider than the phy
context allows.
To avoid this issue, always initialize rs with 20mhz bandwidth rate, and
after authorization, when the phy context is already up-to-date, re-init
rs with the correct bw.
In IBSS, the mac80211 sets the cab_queue to be invalid.
However, the multicast station uses it, so we need to override it.
A previous patch did it, but it was nested inside the if's and was
applied only for legacy FWs that don't support the new station type
API, instead of being applied for all paths.
In addition, add a missing NL80211_IFTYPE_ADHOC to the initialization
of the queues in iwl_mvm_mac_ctxt_init()
Fixes: ee48b72211f8 ("iwlwifi: mvm: support ibss in dqa mode") Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A previous patch allowed the same PN for packets originating from the
same AMSDU by copying PN only for the last packet in the series.
This however is bogus since we cannot assume the last frame will be
received on the same queue, and if it is received on a different ueue
we will end up not incrementing the PN and possibly let the next
packet to have the same PN and pass through.
Change the logic instead to driver explicitly indicate for the second
sub frame and on to be allowed to have the same PN as the first
subframe. Indicate it to mac80211 as well for the fallback queue.
Fixes: f1ae02b186d9 ("iwlwifi: mvm: allow same PN for de-aggregated AMSDU") Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Trying to boot an RK3328 box with an HS200-capable eMMC, I see said eMMC
fail to initialise as it can't run its tuning procedure, because the
sample clock is missing. Upon closer inspection, whilst the clock is
present in the DT, its name is subtly incorrect per the binding, so
__of_clk_get_by_name() never finds it. By inspection, the drive clock
suffers from a similar problem, so has never worked properly either.
This error has propagated across the 32-bit DTs too, so fix those up.
Trying to boot an RK3328 box with an HS200-capable eMMC, I see said eMMC
fail to initialise as it can't run its tuning procedure, because the
sample clock is missing. Upon closer inspection, whilst the clock is
present in the DT, its name is subtly incorrect per the binding, so
__of_clk_get_by_name() never finds it. By inspection, the drive clock
suffers from a similar problem, so has never worked properly either.
Fix up all instances of the incorrect clock names across the 64-bit DTs.
Fixes: d717f7352ec6 ("arm64: dts: rockchip: add sdmmc/sdio/emmc nodes for RK3328 SoCs") Fixes: b790c2cab5ca ("arm64: dts: add Rockchip rk3368 core dtsi and board dts for the r88 board") Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If remove_commit fails then the lock is left locked while the uobj still
exists. Eventually the kernel will deadlock.
lockdep detects this and says:
test/4221 is leaving the kernel with locks still held!
1 lock held by test/4221:
#0: (&ucontext->cleanup_rwsem){.+.+}, at: [<000000001e5c7523>] rdma_explicit_destroy+0x37/0x120 [ib_uverbs]
Fixes: 4da70da23e9b ("IB/core: Explicitly destroy an object while keeping uobject") Signed-off-by: Leon Romanovsky <leon@kernel.org> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the same attribute is listed twice by the user in the ioctl attribute
list then error unwind can cause the kernel to deref garbage.
This happens when an object with WRITE access is sent twice. The second
parse properly fails but corrupts the state required for the error unwind
it triggers.
Fixing this by making duplicates in the attribute list invalid. This is
not something we need to support.
The ioctl interface is currently recommended to be disabled in kConfig.
Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For AMD Promontory xHCI host, although you can disable USB ports in
BIOS settings, those ports will be enabled anyway after you remove a
device on that port and re-plug it in again. It's a known limitation of
the chip. As a workaround we can clear the PORT_WAKE_BITS.
[commit and code comment rephrasing -Mathias] Signed-off-by: Joe Lee <asmt.swfae@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When exposing data access through debugfs, the correct
debugfs_create_*() functions must be used, depending on data type.
Remove all casts from data pointers passed to debugfs_create_*()
functions, as such casts prevent the compiler from flagging bugs.
Correct all wrong usage:
- clk.rate is unsigned long, not u32,
- clk.flags is u8, not u32, which exposed the successive
clk.rate_offset and clk.src_offset fields.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
HS omaps use irq_save_secure_context() instead of irq_save_context()
so sar_base will never get initialized and irq_sar_clear() gets called
with a wrong address for HS omaps from irq_restore_context().
Starting with commit f4b9f40ae95b ("ARM: OMAP4+: Initialize SAR RAM
base early for proper CPU1 reset for kexec") we have it available,
and this ideally would been fixed with that commit already.
Fixes: f4b9f40ae95b ("ARM: OMAP4+: Initialize SAR RAM base early for
proper CPU1 reset for kexec") Cc: Andrew F. Davis <afd@ti.com> Cc: Dave Gerlach <d-gerlach@ti.com> Cc: Keerthy <j-keerthy@ti.com> Cc: Santosh Shilimkar <ssantosh@kernel.org> Cc: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For platform_suspend_ops, the finish call is too late to re-enable wake
irqs and we need re-enable wake irqs on wake call instead.
Otherwise noirq resume for devices has already happened. And then
dev_pm_disarm_wake_irq() has already disabled the dedicated wake irqs
when the interrupt triggers and the wake irq is never handled.
For devices that are already in PM runtime suspended state when we
enter suspend this means that a possible wake irq will never trigger.
And this can lead into a situation where a device has a pending padconf
wake irq, and the device will stay unresponsive to any further wake
irqs.
This issue can be easily reproduced by setting serial console log level
to zero, letting the serial console idle, and suspend the system from
an ssh terminal. Then try to wake up the system by typing to the serial
console.
Note that this affects only omap3 PRM interrupt as that's currently
the only omap variant that does anything in omap_pm_wake().
In general, for the wake irqs to work, the interrupt must have either
IRQF_NO_SUSPEND or IRQF_EARLY_RESUME set for it to trigger before
dev_pm_disarm_wake_irq() disables the wake irqs.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When more than one GP timers are used as kernel system timers and the
corresponding nodes in device-tree are marked with the same "disabled"
property, then the "attr" field of the property will be initialized
more than once as the property being added to sys file system via
__of_add_property_sysfs().
In __of_add_property_sysfs(), the "name" field of pp->attr.attr is set
directly to the return value of safe_name(), without taking care of
whether it's already a valid pointer to a memory block. If it is, its
old value will always be overwritten by the new one and the memory block
allocated before will a "ghost", then a kmemleak happened.
That the same "disabled" property being added to different nodes of device
tree would cause that kind of kmemleak overhead, at least once.
To fix it, allocate the property dynamically, and delete static one.
Based on patch: https://patchwork.kernel.org/patch/10042045/
arch64-linux-gnu-gcc -c sync.c -o sync/sync.o
sync.c:42:29: fatal error: linux/sync_file.h: No such file or directory
#include <linux/sync_file.h>
^
CFLAGS is not used during the compile step, so the system instead of
kernel headers are used. Fix this by adding CFLAGS to the OBJS compile
rule.
Reported-by: Lei Yang <Lei.Yang@windriver.com> Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org> Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This fixs the following comile warnings with ATA_DEBUG enabled,
which detected by Linaro GCC 5.2-2015.11:
drivers/ata/libata-scsi.c: In function 'ata_scsi_dump_cdb':
./include/linux/kern_levels.h:5:18: warning: format '%d' expects
argument of type 'int', but argument 6 has type 'u64 {aka long
long unsigned int}' [-Wformat=]
This commit enables thresh dma mode as this forces to disable checksuming,
and chooses delay values which make the interface stable.
These changes are needed, because ROCK64 is faced with two problems:
1. tx checksuming does not work with packets larger than 1498,
2. the default delays for tx/rx are not stable when using 1Gbps connection.
Delays were found out with:
https://github.com/ayufan-rock64/linux-build/tree/master/recipes/gmac-delays-test
Switch to use dividing to prevent integer overflow when size is too
big to calculate allocation size properly.
Reported-by: Eric Biggers <ebiggers3@gmail.com> Fixes: 6e6e41c31122 ("ptr_ring: fail early if queue occupies more than KMALLOC_MAX_SIZE") Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
'default N' should be 'default n', though they happen to have the same
effect here, due to undefined symbols (N in this case) evaluating to n
in a tristate sense.
Remove the default from ARC_EMUL_UNALIGNED instead of changing it. bool
and tristate symbols implicitly default to n.
Discovered with the
https://urldefense.proofpoint.com/v2/url?u=https-3A__github.com_ulfalizer_Kconfiglib_blob_master_examples_list-5Fundefined.py&d=DwIBAg&c=DPL6_X_6JkXFx7AXWqB0tg&r=c14YS-cH-kdhTOW89KozFhBtBJgs1zXscZojEZQ0THs&m=WxxD8ozR7QQUVzNCBksiznaisBGO_crN7PBOvAoju8s&s=1LmxsNqxwT-7wcInVpZ6Z1J27duZKSoyKxHIJclXU_M&e=
script.
mesh TTL offset in Mesh Channel Switch Parameters element depends on
not only Secondary Channel Offset element, but also affected by
HT Control field and Wide Bandwidth Channel Switch element.
So use element structure to manipulate mesh channel swich param IE
after removing its constant attribution to correct the miscalculation.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We now have a platform (Ranchu) in the "generic" platform which matches
based on the FDT compatible string using mips_machine_is_compatible(),
however that function doesn't stop at a blank struct
of_device_id::compatible as that is an array in the struct, not a
pointer to a string.
Fix the loop completion to check the first byte of the compatible array
rather than the address of the compatible array in the struct.
The recent LPM changes to setup_rfi_flush() are causing some section
mismatch warnings because we removed the __init annotation on
setup_rfi_flush():
The function setup_rfi_flush() references
the function __init ppc64_bolted_size().
the function __init memblock_alloc_base().
The references are actually in init_fallback_flush(), but that is
inlined into setup_rfi_flush().
These references are safe because:
- only pseries calls setup_rfi_flush() at runtime
- pseries always passes L1D_FLUSH_FALLBACK at boot
- so the fallback flush area will always be allocated
- so the check in init_fallback_flush() will always return early:
/* Only allocate the fallback flush area once (at boot time). */
if (l1d_flush_fallback_area)
return;
- and therefore we won't actually call the freed init routines.
We should rework the code to make it safer by default rather than
relying on the above, but for now as a quick-fix just add a __ref
annotation to squash the warning.
Fixes: abf110f3e1ce ("powerpc/rfi-flush: Make it possible to call setup_rfi_flush() again") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
After migration the security feature flags might have changed (e.g.,
destination system with unpatched firmware), but some flags are not
set/clear again in init_cpu_char_feature_flags() because it assumes
the security flags to be the defaults.
Additionally, if the H_GET_CPU_CHARACTERISTICS hypercall fails then
init_cpu_char_feature_flags() does not run again, which potentially
might leave the system in an insecure or sub-optimal configuration.
So, just restore the security feature flags to the defaults assumed
by init_cpu_char_feature_flags() so it can set/clear them correctly,
and to ensure safe settings are in place in case the hypercall fail.
Fixes: f636c14790ea ("powerpc/pseries: Set or clear security feature flags")
Depends-on: 19887d6a28e2 ("powerpc: Move default security feature flags") Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The fallback RFI flush is used when firmware does not provide a way
to flush the cache. It's a "displacement flush" that evicts useful
data by displacing it with an uninteresting buffer.
The flush has to take care to work with implementation specific cache
replacment policies, so the recipe has been in flux. The initial
slow but conservative approach is to touch all lines of a congruence
class, with dependencies between each load. It has since been
determined that a linear pattern of loads without dependencies is
sufficient, and is significantly faster.
Measuring the speed of a null syscall with RFI fallback flush enabled
gives the relative improvement:
P8 - 1.83x
P9 - 1.75x
The flush also becomes simpler and more adaptable to different cache
geometries.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If there is a possibility that a VM may migrate to a Skylake host,
then the hypervisor should report IA32_ARCH_CAPABILITIES.RSBA[bit 2]
as being set (future work, of course). This implies that
CPUID.(EAX=7,ECX=0):EDX.ARCH_CAPABILITIES[bit 29] should be
set. Therefore, kvm should report this CPUID bit as being supported
whether or not the host supports it. Userspace is still free to clear
the bit if it chooses.
For more information on RSBA, see Intel's white paper, "Retpoline: A
Branch Target Injection Mitigation" (Document Number 337131-001),
currently available at https://bugzilla.kernel.org/show_bug.cgi?id=199511.
Since the IA32_ARCH_CAPABILITIES MSR is emulated in kvm, there is no
dependency on hardware support for this feature.
The CPUID bits of OSXSAVE (function=0x1) and OSPKE (func=0x7, leaf=0x0)
allows user apps to detect if OS has set CR4.OSXSAVE or CR4.PKE. KVM is
supposed to update these CPUID bits when CR4 is updated. Current KVM
code doesn't handle some special cases when updates come from emulator.
Here is one example:
Step 1: guest boots
Step 2: guest OS enables XSAVE ==> CR4.OSXSAVE=1 and CPUID.OSXSAVE=1
Step 3: guest hot reboot ==> QEMU reset CR4 to 0, but CPUID.OSXAVE==1
Step 4: guest os checks CPUID.OSXAVE, detects 1, then executes xgetbv
Step 4 above will cause an #UD and guest crash because guest OS hasn't
turned on OSXAVE yet. This patch solves the problem by comparing the the
old_cr4 with cr4. If the related bits have been changed,
kvm_update_cpuid() needs to be called.
Fix this by sanitizing *resource* before using it to index
current->signal->rlim
Notice that given that speculation windows are large, the policy is to
kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
KASAN uses different routines to map shadow for hot added memory and
memory obtained in boot process. Attempt to offline memory onlined by
normal boot process leads to this:
Trying to vfree() nonexistent vm area (000000005d3b34b9)
WARNING: CPU: 2 PID: 13215 at mm/vmalloc.c:1525 __vunmap+0x147/0x190
Obviously we can't call vfree() to free memory that wasn't allocated via
vmalloc(). Use find_vm_area() to see if we can call vfree().
Unfortunately it's a bit tricky to properly unmap and free shadow
allocated during boot, so we'll have to keep it. If memory will come
online again that shadow will be reused.
Matthew asked: how can you call vfree() on something that isn't a
vmalloc address?
vfree() is able to free any address returned by
__vmalloc_node_range(). And __vmalloc_node_range() gives you any
address you ask. It doesn't have to be an address in [VMALLOC_START,
VMALLOC_END] range.
That's also how the module_alloc()/module_memfree() works on
architectures that have designated area for modules.
[aryabinin@virtuozzo.com: improve comments] Link: http://lkml.kernel.org/r/dabee6ab-3a7a-51cd-3b86-5468718e0390@virtuozzo.com
[akpm@linux-foundation.org: fix typos, reflow comment] Link: http://lkml.kernel.org/r/20180201163349.8700-1-aryabinin@virtuozzo.com Fixes: fa69b5989bb0 ("mm/kasan: add support for memory hotplug") Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reported-by: Paul Menzel <pmenzel+linux-kasan-dev@molgen.mpg.de> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
shmat()'s SHM_REMAP option forbids passing a nil address for; this is in
fact the very first thing we check for. Andrea reported that for
SHM_RND|SHM_REMAP cases we can end up bypassing the initial addr check,
but we need to check again if the address was rounded down to nil. As
of this patch, such cases will return -EINVAL.
Link: http://lkml.kernel.org/r/20180503204934.kk63josdu6u53fbd@linux-n805 Signed-off-by: Davidlohr Bueso <dbueso@suse.de> Reported-by: Andrea Arcangeli <aarcange@redhat.com> Cc: Joe Lawrence <joe.lawrence@redhat.com> Cc: Manfred Spraul <manfred@colorfullife.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Patch series "ipc/shm: shmat() fixes around nil-page".
These patches fix two issues reported[1] a while back by Joe and Andrea
around how shmat(2) behaves with nil-page.
The first reverts a commit that it was incorrectly thought that mapping
nil-page (address=0) was a no no with MAP_FIXED. This is not the case,
with the exception of SHM_REMAP; which is address in the second patch.
I chose two patches because it is easier to backport and it explicitly
reverts bogus behaviour. Both patches ought to be in -stable and ltp
testcases need updated (the added testcase around the cve can be
modified to just test for SHM_RND|SHM_REMAP).
Commit 95e91b831f87 ("ipc/shm: Fix shmat mmap nil-page protection")
worked on the idea that we should not be mapping as root addr=0 and
MAP_FIXED. However, it was reported that this scenario is in fact
valid, thus making the patch both bogus and breaks userspace as well.
For example X11's libint10.so relies on shmat(1, SHM_RND) for lowmem
initialization[1].
[1] https://cgit.freedesktop.org/xorg/xserver/tree/hw/xfree86/os-support/linux/int10/linux.c#n347 Link: http://lkml.kernel.org/r/20180503203243.15045-2-dave@stgolabs.net Fixes: 95e91b831f87 ("ipc/shm: Fix shmat mmap nil-page protection") Signed-off-by: Davidlohr Bueso <dbueso@suse.de> Reported-by: Joe Lawrence <joe.lawrence@redhat.com> Reported-by: Andrea Arcangeli <aarcange@redhat.com> Cc: Manfred Spraul <manfred@colorfullife.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the radix tree underlying the IDR happens to be full and we attempt
to remove an id which is larger than any id in the IDR, we will call
__radix_tree_delete() with an uninitialised 'slot' pointer, at which
point anything could happen. This was easiest to hit with a single
entry at id 0 and attempting to remove a non-0 id, but it could have
happened with 64 entries and attempting to remove an id >= 64.
Roman said:
The syzcaller test boils down to opening /dev/kvm, creating an
eventfd, and calling a couple of KVM ioctls. None of this requires
superuser. And the result is dereferencing an uninitialized pointer
which is likely a crash. The specific path caught by syzbot is via
KVM_HYPERV_EVENTD ioctl which is new in 4.17. But I guess there are
other user-triggerable paths, so cc:stable is probably justified.
Matthew added:
We have around 250 calls to idr_remove() in the kernel today. Many of
them pass an ID which is embedded in the object they're removing, so
they're safe. Picking a few likely candidates:
drivers/firewire/core-cdev.c looks unsafe; the ID comes from an ioctl.
drivers/gpu/drm/amd/amdgpu/amdgpu_ctx.c is similar
drivers/atm/nicstar.c could be taken down by a handcrafted packet
Link: http://lkml.kernel.org/r/20180518175025.GD6361@bombadil.infradead.org Fixes: 0a835c4f090a ("Reimplement IDR and IDA using the radix tree") Reported-by: <syzbot+35666cba7f0a337e2e79@syzkaller.appspotmail.com> Debugged-by: Roman Kagan <rkagan@virtuozzo.com> Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
User-space may invoke ibv_reg_mr and ibv_dereg_mr in different threads.
If ibv_dereg_mr is called after the thread which invoked ibv_reg_mr has
exited, get_pid_task will return NULL and ib_umem_release will not
decrease mm->pinned_vm.
Instead of using threads to locate the mm, use the overall tgid from the
ib_ucontext struct instead. This matches the behavior of ODP and
disassociate in handling the mm of the process that called ibv_reg_mr.
Cc: <stable@vger.kernel.org> Fixes: 87773dd56d54 ("IB: ib_umem_release() should decrement mm->pinned_vm from ib_umem_get") Signed-off-by: Lidong Chen <lidongchen@tencent.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A pio send egress error can occur when the PSM library attempts to
to send a bad packet. That issue is still being investigated.
The pio error interrupt handler then attempts to progress the recovery
of the errored pio send context.
Code inspection reveals that the handling lacks the necessary locking
if that recovery interleaves with a PSM close of the "context" object
contains the pio send context.
The lack of the locking can cause the recovery to access the already
freed pio send context object and incorrectly deduce that the pio
send context is actually a kernel pio send context as shown by the
NULL deref stack below:
Clear the PCR (Processor Compatibility Register) on boot to ensure we
are not running in a compatibility mode.
We've seen this cause problems when a crash (and kdump) occurs while
running compat mode guests. The kdump kernel then runs with the PCR
set and causes problems. The symptom in the kdump kernel (also seen in
petitboot after fast-reboot) is early userspace programs taking
sigills on newer instructions (seen in libc).
Signed-off-by: Michael Neuling <mikey@neuling.org> Cc: stable@vger.kernel.org Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For LSE atomics that read and write a register operand, we need to
ensure that these operands are annotated as "early clobber" if the
register is written before all of the input operands have been consumed.
Failure to do so can result in the compiler allocating the same register
to both operands, leading to splats such as:
Unable to handle kernel paging request at virtual address 11111122222221
[...]
x1 : 1111111122222222 x0 : 1111111122222221
Process swapper/0 (pid: 1, stack limit = 0x000000008209f908)
Call trace:
test_atomic64+0x1360/0x155c
where x0 has been allocated as both the value to be stored and also the
atomic_t pointer.
This patch adds the missing clobbers.
Cc: <stable@vger.kernel.org> Cc: Dave Martin <dave.martin@arm.com> Cc: Robin Murphy <robin.murphy@arm.com> Reported-by: Mark Salter <msalter@redhat.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Depending on whether the kernel is compiled with frame-pointer or not,
the temporary memory location used for the bp parameter in these macros
is referenced relative to the stack pointer or the frame pointer.
Hence we can never reference that parameter when we've modified either
the stack pointer or the frame pointer, because then the compiler would
generate an incorrect stack reference.
Fix this by pushing the temporary memory parameter on a known location on
the stack before modifying the stack- and frame pointers.
Cc: <stable@vger.kernel.org> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Brian Paul <brianp@vmware.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When run raidconfig from Dom0 we found that the Xen DMA heap is reduced,
but Dom Heap is increased by the same size. Tracing raidconfig we found
that the related ioctl() in megaraid_sas will call dma_alloc_coherent()
to apply memory. If the memory allocated by Dom0 is not in the DMA area,
it will exchange memory with Xen to meet the requiment. Later drivers
call dma_free_coherent() to free the memory, on xen_swiotlb_free_coherent()
the check condition (dev_addr + size - 1 <= dma_mask) is always false,
it prevents calling xen_destroy_contiguous_region() to return the memory
to the Xen DMA heap.
This issue introduced by commit 6810df88dcfc2 "xen-swiotlb: When doing
coherent alloc/dealloc check before swizzling the MFNs.".
Signed-off-by: Joe Jin <joe.jin@oracle.com> Tested-by: John Sobecki <john.sobecki@oracle.com> Reviewed-by: Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: stable@vger.kernel.org Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
While whitelisting Micron M500DC drives, the tweaked blacklist entry
enabled queued TRIM from M500IT variants also. But these do not support
queued TRIM. And while using those SSDs with the latest kernel we have
seen errors and even the partition table getting corrupted.
Some part from the dmesg:
[ 6.727384] ata1.00: ATA-9: Micron_M500IT_MTFDDAK060MBD, MU01, max UDMA/133
[ 6.727390] ata1.00: 117231408 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 6.741026] ata1.00: supports DRM functions and may not be fully accessible
[ 6.759887] ata1.00: configured for UDMA/133
[ 6.762256] scsi 0:0:0:0: Direct-Access ATA Micron_M500IT_MT MU01 PQ: 0 ANSI: 5
and then for the error:
[ 120.860334] ata1.00: exception Emask 0x1 SAct 0x7ffc0007 SErr 0x0 action 0x6 frozen
[ 120.860338] ata1.00: irq_stat 0x40000008
[ 120.860342] ata1.00: failed command: SEND FPDMA QUEUED
[ 120.860351] ata1.00: cmd 64/01:00:00:00:00/00:00:00:00:00/a0 tag 0 ncq dma 512 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x5 (timeout)
[ 120.860353] ata1.00: status: { DRDY }
[ 120.860543] ata1: hard resetting link
[ 121.166128] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 121.166376] ata1.00: supports DRM functions and may not be fully accessible
[ 121.186238] ata1.00: supports DRM functions and may not be fully accessible
[ 121.204445] ata1.00: configured for UDMA/133
[ 121.204454] ata1.00: device reported invalid CHS sector 0
[ 121.204541] sd 0:0:0:0: [sda] tag#18 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08
[ 121.204546] sd 0:0:0:0: [sda] tag#18 Sense Key : 0x5 [current]
[ 121.204550] sd 0:0:0:0: [sda] tag#18 ASC=0x21 ASCQ=0x4
[ 121.204555] sd 0:0:0:0: [sda] tag#18 CDB: opcode=0x93 93 08 00 00 00 00 00 04 28 80 00 00 00 30 00 00
[ 121.204559] print_req_error: I/O error, dev sda, sector 272512
After few reboots with these errors, and the SSD is corrupted.
After blacklisting it, the errors are not seen and the SSD does not get
corrupted any more.
Fixes: 243918be6393 ("libata: Do not blacklist Micron M500DC") Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: stable@vger.kernel.org Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The SDHCI_QUIRK2_HOST_OFF_CARD_ON is needed for the driver to
properly reset the host controller (reset all) on initialization
after exiting deep sleep.
Signed-off-by: Corneliu Doban <corneliu.doban@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Reviewed-by: Srinath Mannam <srinath.mannam@broadcom.com> Fixes: c833e92bbb60 ("mmc: sdhci-iproc: support standard byte register accesses") Cc: stable@vger.kernel.org # v4.10+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the host controller accepts only 32bit writes, the value of the
16bit TRANSFER_MODE register, that has the same 32bit address as the
16bit COMMAND register, needs to be saved and it will be written
in a 32bit write together with the command as this will trigger the
host to send the command on the SD interface.
When sending the tuning command, TRANSFER_MODE is written and then
sdhci_set_transfer_mode reads it back to clear AUTO_CMD12 bit and
write it again resulting in wrong value to be written because the
initial write value was saved in a shadow and the read-back returned
a wrong value, from the register.
Fix sdhci_iproc_readw to return the saved value of TRANSFER_MODE
when a saved value exist.
Same fix for read of BLOCK_SIZE and BLOCK_COUNT registers, that are
saved for a different reason, although a scenario that will cause the
mentioned problem on this registers is not probable.
Remove hard coded mmc cap 1.8v from platform data as it is board specific.
The 1.8v DDR mmc caps can be enabled using DTS property for those
boards that support it.
For anything NFS-exported we do _not_ want to unlock new inode
before it has grown an alias; original set of fixes got the
ordering right, but missed the nasty complication in case of
lockdep being enabled - unlock_new_inode() does
lockdep_annotate_inode_mutex_key(inode)
which can only be done before anyone gets a chance to touch
->i_mutex. Unfortunately, flipping the order and doing
unlock_new_inode() before d_instantiate() opens a window when
mkdir can race with open-by-fhandle on a guessed fhandle, leading
to multiple aliases for a directory inode and all the breakage
that follows from that.
Correct solution: a new primitive (d_instantiate_new())
combining these two in the right order - lockdep annotate, then
d_instantiate(), then the rest of unlock_new_inode(). All
combinations of d_instantiate() with unlock_new_inode() should
be converted to that.
Cc: stable@kernel.org # 2.6.29 and later Tested-by: Mike Marshall <hubcap@omnibond.com> Reviewed-by: Andreas Dilger <adilger@dilger.ca> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit f65e0d299807 ("ALSA: timer: Call notifier in the same spinlock")
combined the start/continue and stop/pause functions, and in doing so
changed the event code for the pause case to SNDRV_TIMER_EVENT_CONTINUE.
Change it back to SNDRV_TIMER_EVENT_PAUSE.
Fixes: f65e0d299807 ("ALSA: timer: Call notifier in the same spinlock") Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Cc: stable@vger.kernel.org Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
kill_ioctx() used to have an explicit RCU delay between removing the
reference from ->ioctx_table and percpu_ref_kill() dropping the refcount.
At some point that delay had been removed, on the theory that
percpu_ref_kill() itself contained an RCU delay. Unfortunately, that was
the wrong kind of RCU delay and it didn't care about rcu_read_lock() used
by lookup_ioctx(). As the result, we could get ctx freed right under
lookup_ioctx(). Tejun has fixed that in a6d7cff472e ("fs/aio: Add explicit
RCU grace period when freeing kioctx"); however, that fix is not enough.
Suppose io_destroy() from one thread races with e.g. io_setup() from another;
CPU1 removes the reference from current->mm->ioctx_table[...] just as CPU2
has picked it (under rcu_read_lock()). Then CPU1 proceeds to drop the
refcount, getting it to 0 and triggering a call of free_ioctx_users(),
which proceeds to drop the secondary refcount and once that reaches zero
calls free_ioctx_reqs(). That does
INIT_RCU_WORK(&ctx->free_rwork, free_ioctx);
queue_rcu_work(system_wq, &ctx->free_rwork);
and schedules freeing the whole thing after RCU delay.
In the meanwhile CPU2 has gotten around to percpu_ref_get(), bumping the
refcount from 0 to 1 and returned the reference to io_setup().
Tejun's fix (that queue_rcu_work() in there) guarantees that ctx won't get
freed until after percpu_ref_get(). Sure, we'd increment the counter before
ctx can be freed. Now we are out of rcu_read_lock() and there's nothing to
stop freeing of the whole thing. Unfortunately, CPU2 assumes that since it
has grabbed the reference, ctx is *NOT* going away until it gets around to
dropping that reference.
The fix is obvious - use percpu_ref_tryget_live() and treat failure as miss.
It's not costlier than what we currently do in normal case, it's safe to
call since freeing *is* delayed and it closes the race window - either
lookup_ioctx() comes before percpu_ref_kill() (in which case ctx->users
won't reach 0 until the caller of lookup_ioctx() drops it) or lookup_ioctx()
fails, ctx->users is unaffected and caller of lookup_ioctx() doesn't see
the object in question at all.
Cc: stable@kernel.org Fixes: a6d7cff472e "fs/aio: Add explicit RCU grace period when freeing kioctx" Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We recently had an oops reported on a 4.14 kernel in
xfs_reclaim_inodes_count() where sb->s_fs_info pointed to garbage
and so the m_perag_tree lookup walked into lala land. It produces
an oops down this path during the failed mount:
The problem is that the superblock shrinker is running before the
filesystem structures it depends on have been fully set up. i.e.
the shrinker is registered in sget(), before ->fill_super() has been
called, and the shrinker can call into the filesystem before
fill_super() does it's setup work. Essentially we are exposed to
both use-after-free and use-before-initialisation bugs here.
To fix this, add a check for the SB_BORN flag in super_cache_count.
In general, this flag is not set until ->fs_mount() completes
successfully, so we know that it is set after the filesystem
setup has completed. This matches the trylock_super() behaviour
which will not let super_cache_scan() run if SB_BORN is not set, and
hence will not allow the superblock shrinker from entering the
filesystem while it is being set up or after it has failed setup
and is being torn down.
Cc: stable@kernel.org Signed-Off-By: Dave Chinner <dchinner@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
we unlock the directory hash too early - if we are looking at secondary
link and primary (in another directory) gets removed just as we unlock,
we could have the old primary moved in place of the secondary, leaving
us to look into freed entry (and leaving our dentry with ->d_fsdata
pointing to a freed entry).
Cc: stable@vger.kernel.org # 2.4.4+ Acked-by: David Sterba <dsterba@suse.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Check the TIF_32BIT_FPREGS task setting of the tracee rather than the
tracer in determining the layout of floating-point general registers in
the floating-point context, correcting access to odd-numbered registers
for o32 tracees where the setting disagrees between the two processes.
Fixes: 597ce1723e0f ("MIPS: Support for 64-bit FP with O32 binaries") Signed-off-by: Maciej W. Rozycki <macro@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: <stable@vger.kernel.org> # 3.14+ Signed-off-by: James Hogan <jhogan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Correct commit 7aeb753b5353 ("MIPS: Implement task_user_regset_view.")
and expose the FIR register using the unused 4 bytes at the end of the
NT_PRFPREG regset. Without that register included clients cannot use
the PTRACE_GETREGSET request to retrieve the complete FPU register set
and have to resort to one of the older interfaces, either PTRACE_PEEKUSR
or PTRACE_GETFPREGS, to retrieve the missing piece of data. Also the
register is irreversibly missing from core dumps.
This register is architecturally hardwired and read-only so the write
path does not matter. Ignore data supplied on writes then.
Fixes: 7aeb753b5353 ("MIPS: Implement task_user_regset_view.") Signed-off-by: James Hogan <jhogan@kernel.org> Signed-off-by: Maciej W. Rozycki <macro@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: <stable@vger.kernel.org> # 3.13+
Patchwork: https://patchwork.linux-mips.org/patch/19273/ Signed-off-by: James Hogan <jhogan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When DMA will be performed to a MIPS32 1004K CPS, the L1-cache for the
range needs to be flushed and invalidated first.
The code currently takes one of two approaches.
1/ If the range is less than the size of the dcache, then HIT type
requests flush/invalidate cache lines for the particular addresses.
HIT-type requests a globalised by the CPS so this is safe on SMP.
2/ If the range is larger than the size of dcache, then INDEX type
requests flush/invalidate the whole cache. INDEX type requests affect
the local cache only. CPS does not propagate them in any way. So this
invalidation is not safe on SMP CPS systems.
Data corruption due to '2' can quite easily be demonstrated by
repeatedly "echo 3 > /proc/sys/vm/drop_caches" and then sha1sum a file
that is several times the size of available memory. Dropping caches
means that large contiguous extents (large than dcache) are more likely.
This was not a problem before Linux-4.8 because option 2 was never used
if CONFIG_MIPS_CPS was defined. The commit which removed that apparently
didn't appreciate the full consequence of the change.
We could, in theory, globalize the INDEX based flush by sending an IPI
to other cores. These cache invalidation routines can be called with
interrupts disabled and synchronous IPI require interrupts to be
enabled. Asynchronous IPI may not trigger writeback soon enough. So we
cannot use IPI in practice.
We can already test if IPI would be needed for an INDEX operation with
r4k_op_needs_ipi(R4K_INDEX). If this is true then we mustn't try the
INDEX approach as we cannot use IPI. If this is false (e.g. when there
is only one core and hence one L1 cache) then it is safe to use the
INDEX approach without IPI.
This patch avoids options 2 if r4k_op_needs_ipi(R4K_INDEX), and so
eliminates the corruption.
BugLink: https://bugs.launchpad.net/bugs/1785282
In IORT issue C SMMUv3 IORT nodes gained an additional field (DeviceID
mapping index) so that the SMMUv3 can describe its MSI interrupts.
Referring to it in the kernel requires ACPICA changes and in order
to prevent kernel<->ACPICA dependencies kernel code depending on the
SMMUv3 DeviceID mapping index field was guarded with an ACPICA version
conditional.
ACPICA changes introducing DeviceID mapping index in the IORT structs
were integrated in the kernel with:
commit 4c106aa411ee ("ACPICA: iasl: Add SMMUv3 device ID mapping index
support")
so the temporary ACPICA guard has become stale and can be removed.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Hanjun Guo <hanjun.guo@linaro.org> Cc: Will Deacon <will.deacon@arm.com> Cc: Hanjun Guo <hanjun.guo@linaro.org> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
(cherry picked from commit 6c47506361ecd9591813bbaaca518f8a76162a3d) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Kleber Souza <kleber.souza@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
SMMUv3 device ID mapping index is used for SMMUv3
MSI which is introduced in IORT spec revision c,
add its support for iasl.
Tested with iasl -t IORT then get the right SMMUv3
node in iort.asl.
Link: https://github.com/acpica/acpica/commit/5c371879 Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Erik Schmauss <erik.schmauss@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
(cherry picked from commit 4c106aa411ee7c1919589f283a4f17888dfee387) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Kleber Souza <kleber.souza@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Sinan Kaya [Fri, 10 Aug 2018 15:37:01 +0000 (11:37 -0400)]
scsi: hpsa: disable device during shutdown
BugLink: http://bugs.launchpad.net/bugs/1772467
'Commit cc27b735ad3a ("PCI/portdrv: Turn off PCIe services during
shutdown")' has been added to kernel to shutdown pending PCIe port service
interrupts during reboot so that a newly started kexec kernel wouldn't
observe pending interrupts.
pcie_port_device_remove() is disabling the root port and switches by
calling pci_disable_device() after all PCIe service drivers are shutdown.
This has been found to cause crashes on HP DL360 Gen9 machines during
reboot due to hpsa driver not clearing the bus master bit during the
shutdown procedure by calling pci_disable_device().
Disable device as part of the shutdown sequence.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org> Link: https://bugzilla.kernel.org/show_bug.cgi?id=199779 Fixes: cc27b735ad3a ("PCI/portdrv: Turn off PCIe services during shutdown") Cc: stable@vger.kernel.org Reported-by: Ryan Finnie <ryan@finnie.org> Tested-by: Don Brace <don.brace@microsemi.com> Acked-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 0d98ba8d70b0070ac117452ea0b663e26bbf46bf) Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Kleber Souza <kleber.souza@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
George Cherian [Tue, 14 Aug 2018 16:57:27 +0000 (11:57 -0500)]
i2c: xlp9xx: Add support for SMBAlert
Add support for SMBus alert mechanism to i2c-xlp9xx driver.
The second interrupt is parsed to use for SMBus alert.
The first interrupt is the i2c controller main interrupt.
BugLink: https://launchpad.net/bugs/1786981 Signed-off-by: Kamlakant Patel <kamlakant.patel@cavium.com> Signed-off-by: George Cherian <george.cherian@cavium.com> Reviewed-by: Jan Glauber <jglauber@cavium.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
(cherry picked from commit 40f4e372cba8a6729c997c0bda1fa03adf7f956e) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Kleber Souza <kleber.souza@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Julian Wiedmann [Tue, 14 Aug 2018 19:12:29 +0000 (15:12 -0400)]
s390/qeth: don't clobber buffer on async TX completion
BugLink: https://bugs.launchpad.net/bugs/1786057
If qeth_qdio_output_handler() detects that a transmit requires async
completion, it replaces the pending buffer's metadata object
(qeth_qdio_out_buffer) so that this queue buffer can be re-used while
the data is pending completion.
Later when the CQ indicates async completion of such a metadata object,
qeth_qdio_cq_handler() tries to free any data associated with this
object (since HW has now completed the transfer). By calling
qeth_clear_output_buffer(), it erronously operates on the queue buffer
that _previously_ belonged to this transfer ... but which has been
potentially re-used several times by now.
This results in double-free's of the buffer's data, and failing
transmits as the buffer descriptor is scrubbed in mid-air.
The correct way of handling this situation is to
1. scrub the queue buffer when it is prepared for re-use, and
2. later obtain the data addresses from the async-completion notifier
(ie. the AOB), instead of the queue buffer.
All this only affects qeth devices used for af_iucv HiperTransport.
Fixes: 0da9581ddb0f ("qeth: exploit asynchronous delivery of storage blocks") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit ce28867fd20c23cd769e78b4d619c4755bf71a1c) Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Kleber Souza <kleber.souza@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1787058
Some ThinkPad systems have a power-saving feature that turns off HDMI
audio device in Windows, but NVidia Linux driver does not support this
feature. As a result, HDMI audio will not work on Linux.
A BIOS workaround is added with an OEM_OSI string
"Linux-Lenovo-NV-HDMI-Audio" to power on NVidia HDMI audio when booting.
The form of the OEM _OSI strings is defined by each OEMs and is
discussed in Documentation/acpi/osi.txt.
Signed-off-by: Alex Hung <alex.hung@canonical.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
(cherry picked from commit 887532ca7ca59fcf0547a79211756791128030a3) Signed-off-by: Alex Hung <alex.hung@canonical.com> Acked-by: Shrirang Bagul <shrirang.bagul@canonical.com> Acked-by: Kleber Souza <kleber.souza@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
George Cherian [Wed, 15 Aug 2018 15:58:08 +0000 (10:58 -0500)]
i2c: xlp9xx: Fix case where SSIF read transaction completes early
During ipmi stress tests we see occasional failure of transactions
at the boot time. This happens in the case of a I2C_M_RECV_LEN
transactions, when the read transfer completes (with the initial
read length of 34) before the driver gets a chance to handle interrupts.
The current driver code expects at least 2 interrupts for I2C_M_RECV_LEN
transactions. The length is updated during the first interrupt, and the
buffer contents are only copied during subsequent interrupts. In case of
just one interrupt, we will complete the transaction without copying
out the bytes from RX fifo.
Update the code to drain the RX fifo after the length update,
so that the transaction completes correctly in all cases.
Jan Glauber [Fri, 17 Aug 2018 14:42:06 +0000 (09:42 -0500)]
crypto: cavium - Fix smp_processor_id() warnings
Switch to raw_smp_processor_id() to prevent a number of
warnings from kernel debugging. We do not care about
preemption here, as the CPU number is only used as a
poor mans load balancing or device selection. If preemption
happens during a compress/decompress operation a small performance
hit will occur but everything will continue to work, so just
ignore it.
BugLink: https://launchpad.net/bugs/1787469 Signed-off-by: Jan Glauber <jglauber@cavium.com> Reviewed-by: Robert Richter <rrichter@cavium.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
(cherry picked from commit e7a9b05ca4c707ff4b46a77963db48d085d383e0) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Jan Glauber [Fri, 17 Aug 2018 14:42:05 +0000 (09:42 -0500)]
crypto: cavium - Fix statistics pending request value
The pending request counter was read from the wrong register. While
at it, there is no need to use an atomic for it as it is only read
localy in a loop.
BugLink: https://launchpad.net/bugs/1787469 Signed-off-by: Jan Glauber <jglauber@cavium.com> Reviewed-by: Robert Richter <rrichter@cavium.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
(cherry picked from commit 1cc7e01ff977770ce0651f4d347a84e360835c3b) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Jan Glauber [Fri, 17 Aug 2018 14:42:03 +0000 (09:42 -0500)]
crypto: cavium - Limit result reading attempts
After issuing a request an endless loop was used to read the
completion state from memory which is asynchronously updated
by the ZIP coprocessor.
Add an upper bound to the retry attempts to prevent a CPU getting stuck
forever in case of an error. Additionally, add a read memory barrier
and a small delay between the reading attempts.
BugLink: https://launchpad.net/bugs/1787469 Signed-off-by: Jan Glauber <jglauber@cavium.com> Reviewed-by: Robert Richter <rrichter@cavium.com> Cc: stable <stable@vger.kernel.org> # 4.14 Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
(cherry picked from commit c782a8c43e94ba6c09e9de2d69b5e3a5840ce61c) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Jan Glauber [Fri, 17 Aug 2018 14:42:02 +0000 (09:42 -0500)]
crypto: cavium - Fix fallout from CONFIG_VMAP_STACK
Enabling virtual mapped kernel stacks breaks the thunderx_zip
driver. On compression or decompression the executing CPU hangs
in an endless loop. The reason for this is the usage of __pa
by the driver which does no longer work for an address that is
not part of the 1:1 mapping.
The zip driver allocates a result struct on the stack and needs
to tell the hardware the physical address within this struct
that is used to signal the completion of the request.
As the hardware gets the wrong address after the broken __pa
conversion it writes to an arbitrary address. The zip driver then
waits forever for the completion byte to contain a non-zero value.
Allocating the result struct from 1:1 mapped memory resolves this
bug.
BugLink: https://launchpad.net/bugs/1787469 Signed-off-by: Jan Glauber <jglauber@cavium.com> Reviewed-by: Robert Richter <rrichter@cavium.com> Cc: stable <stable@vger.kernel.org> # 4.14 Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
(cherry picked from commit 37ff02acaa3d7be87ecb89f198a549ffd3ae2403) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Michal Wnukowski [Fri, 17 Aug 2018 18:27:53 +0000 (14:27 -0400)]
nvme-pci: add a memory barrier to nvme_dbbuf_update_and_check_event
BugLink: https://bugs.launchpad.net/bugs/1788222
In many architectures loads may be reordered with older stores to
different locations. In the nvme driver the following two operations
could be reordered:
- Write shadow doorbell (dbbuf_db) into memory.
- Read EventIdx (dbbuf_ei) from memory.
This can result in a potential race condition between driver and VM host
processing requests (if given virtual NVMe controller has a support for
shadow doorbell). If that occurs, then the NVMe controller may decide to
wait for MMIO doorbell from guest operating system, and guest driver may
decide not to issue MMIO doorbell on any of subsequent commands.
This issue is purely timing-dependent one, so there is no easy way to
reproduce it. Currently the easiest known approach is to run "Oracle IO
Numbers" (orion) that is shipped with Oracle DB:
Where nvme_test is a .lun file that contains a list of NVMe block
devices to run test against. Limiting number of vCPUs assigned to given
VM instance seems to increase chances for this bug to occur. On test
environment with VM that got 4 NVMe drives and 1 vCPU assigned the
virtual NVMe controller hang could be observed within 10-20 minutes.
That correspond to about 400-500k IO operations processed (or about
100GB of IO read/writes).
Orion tool was used as a validation and set to run in a loop for 36
hours (equivalent of pushing 550M IO operations). No issues were
observed. That suggest that the patch fixes the issue.
Fixes: f9f38e33389c ("nvme: improve performance for virtual NVMe devices") Signed-off-by: Michal Wnukowski <wnukowski@google.com> Reviewed-by: Keith Busch <keith.busch@intel.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
[hch: updated changelog and comment a bit] Signed-off-by: Christoph Hellwig <hch@lst.de>
(cherry-picked from 07e860202d187d35ad24f0100caa0d244d4df2af git://git.infradead.org/nvme.git ) Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Kleber Souza <kleber.souza@canonical.com> Acked-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1789227
When CONFIG_NVME_MULTIPATH is set, but we're not using nvme to multipath,
namespaces with multiple paths were not creating unique names due to
reusing the same instance number from the namespace's head.
This patch fixes this by falling back to the non-multipath naming method
when the parameter disabled using multipath.
Reported-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Keith Busch <keith.busch@intel.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
(cherry-picked from a785dbccd95c37606c720580714f5a7a8b3255f1) Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
[ kleber: fixed launchpad bug number ] Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Paul Meyer [Fri, 3 Aug 2018 14:49:07 +0000 (10:49 -0400)]
UBUNTU: [Debian] hyper-v -- Ensure that hv-kvp-daemon.service starts before walinuxagent.service
BugLink: https://bugs.launchpad.net/bugs/1739107
The hv-kvp-daemon service starts after walinuxagent. The default dependencies make hv-kvp-daemon
wait until the whole system is up before it can start, which is not necessary and blocks Azure
telemetry use case. This commit changes the hv-kvp-daemon.service unit file to start it up as
early as possible so that the channel for telemetry can be use.
Signed-off-by: Eric Desrochers <eric.desrochers@canonical.com> Acked-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
dann frazier [Tue, 31 Jul 2018 19:41:55 +0000 (13:41 -0600)]
hinic: Link the logical network device to the pci device in sysfs
BugLink: https://bugs.launchpad.net/bugs/1783138
Otherwise interfaces get exposed under /sys/devices/virtual, which
doesn't give udev the context it needs for PCI-based predictable
interface names.
Signed-off-by: dann frazier <dann.frazier@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 7856e8616273098dc6c09a6e084afd98a283ff0d) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Kleber Souza <kleber.souza@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
ACPI / LPSS: Avoid PM quirks on suspend and resume from hibernation
BugLink: https://bugs.launchpad.net/bugs/1774950
Commit a09c59130688 (ACPI / LPSS: Avoid PM quirks on suspend and
resume from S3) modified the ACPI driver for Intel SoCs (LPSS) to
avoid applying PM quirks on suspend and resume from S3 to address
system-wide suspend and resume problems on some systems, but it is
reported that the same issue also affects hibernation, so extend
the approach used by that commit to cover hibernation as well.
Fixes: a09c59130688 (ACPI / LPSS: Avoid PM quirks on suspend and resume from S3) Link: https://bugs.launchpad.net/bugs/1774950 Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: 4.15+ <stable@vger.kernel.org> # 4.15+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
(cherry picked from commit 12864ff8545f6b8144fdf1bb89b5663357f29ec4) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>