platform/x86: asus-wireless: Use per-HID HSWC parameters
Some Asus machines use 0x4/0x5 as their LED on/off values, while others
use 0x0/0x1, as shown in the DSDT excerpts below. Luckily it seems this
behavior is tied to different HIDs, after looking at 44 DSDTs from
different Asus models.
Another small difference is that a few of them call GWBL instead of
OWGS, and SWBL instead of OWGD. That does not seem to make a difference
for asus-wireless, and is additional reasoning to not try to call these
methods directly.
This patch adds the PCI Device id for Power Management Controller on Intel
Apollo Lake platforms.
Intel PMC IPC Driver loads as a platform driver on Apollo Lake platforms
since Intel BIOS hides the PCI Configuration space for 0:13:1 and
re-enumerates it as ACPI device (INT34D2). The correct PCI Device ID should
be added if some platform firmware choses to enumerate the device via PCI
space.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Shanth Murthy [Mon, 13 Feb 2017 12:02:52 +0000 (04:02 -0800)]
platform/x86: intel_pmc_ipc: read s0ix residency API
This patch adds a new API to indicate S0ix residency in usec. It utilizes
the PMC Global Control Registers (GCR) to read deep and shallow
S0ix residency.
PMC MMIO resources:
o Lower 4kB: IPC1 (PMC inter-processor communication) interface
o Upper 4kB: GCR (Global Control Registers)
This enables the power management framework to take corrective actions when
the platform fails to enter S0ix after kernel freeze as part of the suspend
to idle flow. (echo freeze > /sys/power/state).
This is expected to be used with a S0ix failsafe framework such as:
<https://lwn.net/Articles/689505/>
[rajneesh: folded in "fix division in 32-bit case" from Andy Shevchenko] Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com> Signed-off-by: Shanth Murthy <shanth.murthy@intel.com>
[andy: fixed kbuild error, removed "total" from variables, fixed macro] Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The status register on Intel Merrifield can be read in the similar way
it's done for previous MID platforms. Unify access to PBSTATUS register
via SCU IPC.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Andrey Ryabinin [Thu, 26 Jan 2017 14:27:23 +0000 (17:27 +0300)]
platform/x86: intel_pmc_core: fix out-of-bounds accesses on stack
pmc_core_mtpmc_link_status() an pmc_core_check_read_lock_bit() use
test_bit() on local 32-bit variable. This causes out-of-bounds
access since test_bit() expects object at least of 'unsigned long' size:
Arnd Bergmann [Thu, 2 Feb 2017 14:25:57 +0000 (15:25 +0100)]
platform/x86: silead depends on I2C being built-in
The new driver cannot be a loadable module, so if I2C is loadable, we get this
link error:
drivers/platform/built-in.o: In function `silead_ts_dmi_init':
silead_dmi.c:(.init.text+0x2ef): undefined reference to `i2c_bus_type'
This makes the Kconfig dependency stricter to require I2C=y.
Fixes: 9eeda3897a85 ("platform/x86: add support for devices with Silead touchscreens") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Hans de Goede [Mon, 23 Jan 2017 17:35:30 +0000 (18:35 +0100)]
platform/x86: add support for devices with Silead touchscreens
On ACPI based tablets, the ACPI touchscreen node only contains info on
the gpio and the irq, and is missing any info on the axis. This info is
expected to be built into the tablet model specific version of the driver
shipped with the os-image for the device.
Add support for getting the missing info from a table built into the
driver, using dmi data to identify which entry of the table to use and
add info for the CUBE iwork8 Air and Jumper EZpad mini3 tablets on which
this code was tested / developed.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=187531 Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[dmitry.torokhov@gmail.com: Move to platform/x86] Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[andy: fixed merge conflict] Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
platform/x86: Support Turbo Boost Max 3.0 for non HWP systems
On platforms supporting Intel Turbo Boost Max Technology 3.0, the
maximum turbo frequencies (turbo ratio) of some cores in a CPU package
may be higher than the other cores in the same package. In that case,
better performance can be achieved by making the scheduler prefer to run
tasks on the CPUs with higher max turbo frequencies.
On Intel® Broadwell Xeon systems, it is optional to turn on HWP
(Hardware P-States). When HWP is not turned on, the BIOS doesn't
present required CPPC (Collaborative Processor Performance Control)
tables. This table is used to get the per CPU core maximum performance
ratio and inform scheduler (in cpufreq/intel_pstate driver).
On such systems the maximum performance ratio can be read via over
clocking (OC) mailbox interface for each CPU. This interface is not
architectural and can change for every model of processors.
This driver reads maximum performance ratio of each CPU and set up
the scheduler priority metrics. In this way scheduler can prefer CPU
with higher performance to schedule tasks.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Michał Kępień [Wed, 11 Jan 2017 08:59:32 +0000 (09:59 +0100)]
platform/x86: fujitsu-laptop: break up complex loop condition
The loop condition in acpi_fujitsu_hotkey_release() includes an
assignment, a four-argument function call and a comparison, making it
hard to read. Separate the assignment from the comparison to improve
readability.
Signed-off-by: Michał Kępień <kernel@kempniu.pl> Acked-by: Jonathan Woithe <jwoithe@just42.net> Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Michał Kępień [Wed, 11 Jan 2017 08:59:31 +0000 (09:59 +0100)]
platform/x86: fujitsu-laptop: move keycode processing to separate functions
acpi_fujitsu_hotkey_notify() is pretty deeply nested, which hurts
readability. Move the keycode processing part to two separate functions
to make the code easier to understand and save a few line breaks.
Rename variable keycode_r to keycode as there is no longer any need to
differentiate between the two. Tweak indentations to make checkpatch
happy.
Signed-off-by: Michał Kępień <kernel@kempniu.pl> Acked-by: Jonathan Woithe <jwoithe@just42.net> Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Michał Kępień [Wed, 11 Jan 2017 08:59:30 +0000 (09:59 +0100)]
platform/x86: fujitsu-laptop: decrease indentation in acpi_fujitsu_hotkey_notify()
acpi_fujitsu_hotkey_notify() is pretty deeply nested, which hurts
readability. Strip off one level of indentation by returning early when
the event code supplied as argument is not ACPI_FUJITSU_NOTIFY_CODE1.
Signed-off-by: Michał Kępień <kernel@kempniu.pl> Acked-by: Jonathan Woithe <jwoithe@just42.net> Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Now that call_fext_func() is invoked by logolamp_set() for both
LOGOLAMP_POWERON and LOGOLAMP_ALWAYS for every brightness value,
logolamp_get() can be simplified to decrease indentation and number of
local variables.
Signed-off-by: Michał Kępień <kernel@kempniu.pl> Acked-by: Jonathan Woithe <jwoithe@just42.net> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Michał Kępień [Mon, 9 Jan 2017 13:14:16 +0000 (14:14 +0100)]
platform/x86: fujitsu-laptop: rework logolamp_set() to properly handle errors
Potential errors returned by some call_fext_func() calls inside
logolamp_set() are currently ignored. Rework logolamp_set() to properly
handle them. This causes one more call_fext_func() call to be made in
the LED_OFF case, though one could argue that this is logically the
right thing to do (even though the extra call is not needed to shut the
LED off).
Signed-off-by: Michał Kępień <kernel@kempniu.pl> Acked-by: Jonathan Woithe <jwoithe@just42.net> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Jean Delvare [Thu, 5 Jan 2017 08:14:43 +0000 (09:14 +0100)]
platform/x86: dell-smbios: Auto-select as needed
Dell-smbios is a helper module, it serves no purpose on its own, so
do not present it as an option to the user. Instead, select it
automatically whenever a driver which needs it is selected.
Also select DCDBAS as needed, instead of depending on it, so that
the Dell driver options are always visible.
As a clean-up, I removed the "default n" statements as they are not
needed (n is the default default.)
Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Michał Kępień <kernel@kempniu.pl> Cc: Pali Rohár <pali.rohar@gmail.com> Cc: Darren Hart <dvhart@infradead.org> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/platform/x86/intel_mid_thermal.ko | grep alias
$
After this patch:
$ modinfo drivers/platform/x86/intel_mid_thermal.ko | grep alias
alias: platform:msic_thermal
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
platform/x86: intel_mid_thermal: Remove duplicated platform device ID
Commit 3fca3d3d5075 ("platform-x86: intel_mid_thermal: add msic_thermal
alias") added a "msic_thermal" entry to the driver's platform device ID
table since that was the platform dev name registered in some platforms
and the only dev in the platform table was "msic_sensor" (DRIVER_NAME).
But then commit 634830704d80 ("x86/mid/thermal: Add msic_thermal alias")
changed DRIVER_NAME from "msic_sensor" to "msic_thermal", and so there's
now duplicated entries in the platform device ID table.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The patch contains several styling fixes:
- Make names of hotplug devices shorter;
- Change register offset assignment to defines;
- Add defines for the all event masks;
- Use PLATFORM_DEVID_NONE instead of -1;
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Lee, Chun-Yi [Thu, 3 Nov 2016 00:18:52 +0000 (08:18 +0800)]
platform/x86: acer-wmi: setup accelerometer when machine has appropriate notify event
The accelerometer event relies on the ACERWMID_EVENT_GUID notify.
So, this patch changes the codes to setup accelerometer input device
when detected ACERWMID_EVENT_GUID. It avoids that the accel input
device created on every Acer machines.
In addition, patch adds a clearly parsing logic of accelerometer hid
to acer_wmi_get_handle_cb callback function. It is positive matching
the "SENR" name with "BST0001" device to avoid non-supported hardware.
Micha? K?pie? [Fri, 16 Dec 2016 14:46:03 +0000 (15:46 +0100)]
platform/x86: fujitsu-laptop: set default trigger for radio LED to rfkill-any
The "radio components indicator" LED present in Lifebook E734/E744/E754
should be lit when any radio transmitter is enabled, so set its default
trigger to rfkill-any.
Signed-off-by: Michał Kępień <kernel@kempniu.pl> Acked-by: Jonathan Woithe <jwoithe@just42.net> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Linus Torvalds [Sun, 29 Jan 2017 21:50:06 +0000 (13:50 -0800)]
drm/i915: Check for NULL i915_vma in intel_unpin_fb_obj()
I've seen this trigger twice now, where the i915_gem_object_to_ggtt()
call in intel_unpin_fb_obj() returns NULL, resulting in an oops
immediately afterwards as the (inlined) call to i915_vma_unpin_fence()
tries to dereference it.
It seems to be some race condition where the object is going away at
shutdown time, since both times happened when shutting down the X
server. The call chains were different:
and this patch purely papers over the issue by adding a NULL pointer
check and a WARN_ON_ONCE() to avoid the oops that would then generally
make the machine unresponsive.
Other callers of i915_gem_object_to_ggtt() seem to also check for the
returned pointer being NULL and warn about it, so this clearly has
happened before in other places.
[ Reported it originally to the i915 developers on Jan 8, applying the
ugly workaround on my own now after triggering the problem for the
second time with no feedback.
Linus Torvalds [Sun, 29 Jan 2017 18:56:56 +0000 (10:56 -0800)]
Merge branch 'parisc-4.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull two parisc fixes from Helge Deller:
"One fix to avoid usage of BITS_PER_LONG in user-space exported swab.h
header which breaks compiling qemu, and one trivial fix for printk
continuation in the parisc parport driver"
* 'parisc-4.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Don't use BITS_PER_LONG in userspace-exported swab.h header
parisc, parport_gsc: Fixes for printk continuation lines
Linus Torvalds [Sat, 28 Jan 2017 23:09:23 +0000 (15:09 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Two I2C driver bugfixes.
The 'VLLS mode support' patch should have been entitled 'reconfigure
pinctrl after suspend' to make the bugfix more clear. Sorry, I missed
that, yet didn't want to rebase"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: imx-lpi2c: add VLLS mode support
i2c: i2c-cadence: Initialize configuration before probing devices
Helge Deller [Sat, 28 Jan 2017 10:52:02 +0000 (11:52 +0100)]
parisc: Don't use BITS_PER_LONG in userspace-exported swab.h header
In swab.h the "#if BITS_PER_LONG > 32" breaks compiling userspace programs if
BITS_PER_LONG is #defined by userspace with the sizeof() compiler builtin.
Solve this problem by using __BITS_PER_LONG instead. Since we now
#include asm/bitsperlong.h avoid further potential userspace pollution
by moving the #define of SHIFT_PER_LONG to bitops.h which is not
exported to userspace.
This patch unbreaks compiling qemu on hppa/parisc.
Linus Torvalds [Sat, 28 Jan 2017 19:50:17 +0000 (11:50 -0800)]
Merge tag 'nfs-for-4.10-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Stable patches:
- NFSv4.1: Fix a deadlock in layoutget
- NFSv4 must not bump sequence ids on NFS4ERR_MOVED errors
- NFSv4 Fix a regression with OPEN EXCLUSIVE4 mode
- Fix a memory leak when removing the SUNRPC module
Bugfixes:
- Fix a reference leak in _pnfs_return_layout"
* tag 'nfs-for-4.10-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
pNFS: Fix a reference leak in _pnfs_return_layout
nfs: Fix "Don't increment lock sequence ID after NFS4ERR_MOVED"
SUNRPC: cleanup ida information when removing sunrpc module
NFSv4.0: always send mode in SETATTR after EXCLUSIVE4
nfs: Don't increment lock sequence ID after NFS4ERR_MOVED
NFSv4.1: Fix a deadlock in layoutget
Linus Torvalds [Sat, 28 Jan 2017 19:09:04 +0000 (11:09 -0800)]
Merge tag 'md/4.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md
Pull MD fixes from Shaohua Li:
"This fixes several corner cases for raid5 cache, which is merged into
this cycle"
* tag 'md/4.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md/r5cache: disable write back for degraded array
md/r5cache: shift complex rmw from read path to write path
md/r5cache: flush data only stripes in r5l_recovery_log()
md/raid5: move comment of fetch_block to right location
md/r5cache: read data into orig_page for prexor of cached data
md/raid5-cache: delete meaningless code
Linus Torvalds [Sat, 28 Jan 2017 19:00:08 +0000 (11:00 -0800)]
Merge tag 'arc-4.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Hopefully last set of changes for ARC for 4.10:
- fix for unaligned access emulation corner case
- fix for udelay loop inline asm regression
- fix irq affinity finally for AXS103 board [Yuriy]
- final fixes for setting IO-coherency sanely in SMP"
* tag 'arc-4.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [arcompact] handle unaligned access delay slot corner case
ARCv2: smp-boot: wake_flag polling by non-Masters needs to be uncached
ARC: smp-boot: Decouple Non masters waiting API from jump to entry point
ARCv2: MCIP: update the BCR per current changes
ARC: udelay: fix inline assembler by adding LP_COUNT to clobber list
ARCv2: MCIP: Deprecate setting of affinity in Device Tree
1) GTP fixes from Andreas Schultz (missing genl module alias, clear IP
DF on transmit).
2) Netfilter needs to reflect the fwmark when sending resets, from Pau
Espin Pedrol.
3) nftable dump OOPS fix from Liping Zhang.
4) Fix erroneous setting of VIRTIO_NET_HDR_F_DATA_VALID on transmit,
from Rolf Neugebauer.
5) Fix build error of ipt_CLUSTERIP when procfs is disabled, from Arnd
Bergmann.
6) Fix regression in handling of NETIF_F_SG in harmonize_features(),
from Eric Dumazet.
7) Fix RTNL deadlock wrt. lwtunnel module loading, from David Ahern.
8) tcp_fastopen_create_child() needs to setup tp->max_window, from
Alexey Kodanev.
9) Missing kmemdup() failure check in ipv6 segment routing code, from
Eric Dumazet.
10) Don't execute unix_bind() under the bindlock, otherwise we deadlock
with splice. From WANG Cong.
11) ip6_tnl_parse_tlv_enc_lim() potentially reallocates the skb buffer,
therefore callers must reload cached header pointers into that skb.
Fix from Eric Dumazet.
12) Fix various bugs in legacy IRQ fallback handling in alx driver, from
Tobias Regnery.
13) Do not allow lwtunnel drivers to be unloaded while they are
referenced by active instances, from Robert Shearman.
14) Fix truncated PHY LED trigger names, from Geert Uytterhoeven.
15) Fix a few regressions from virtio_net XDP support, from John
Fastabend and Jakub Kicinski.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (102 commits)
ISDN: eicon: silence misleading array-bounds warning
net: phy: micrel: add support for KSZ8795
gtp: fix cross netns recv on gtp socket
gtp: clear DF bit on GTP packet tx
gtp: add genl family modules alias
tcp: don't annotate mark on control socket from tcp_v6_send_response()
ravb: unmap descriptors when freeing rings
virtio_net: reject XDP programs using header adjustment
virtio_net: use dev_kfree_skb for small buffer XDP receive
r8152: check rx after napi is enabled
r8152: re-schedule napi for tx
r8152: avoid start_xmit to schedule napi when napi is disabled
r8152: avoid start_xmit to call napi_schedule during autosuspend
net: dsa: Bring back device detaching in dsa_slave_suspend()
net: phy: leds: Fix truncated LED trigger names
net: phy: leds: Break dependency of phy.h on phy_led_triggers.h
net: phy: leds: Clear phy_num_led_triggers on failure to avoid crash
net-next: ethernet: mediatek: change the compatible string
Documentation: devicetree: change the mediatek ethernet compatible string
bnxt_en: Fix RTNL lock usage on bnxt_get_port_module_status().
...
Linus Torvalds [Fri, 27 Jan 2017 20:44:32 +0000 (12:44 -0800)]
Merge tag 'xfs-for-linus-4.10-rc6-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs uodates from Darrick Wong:
"I have some more fixes this week: better input validation, corruption
avoidance, build fixes, memory leak fixes, and a couple from Christoph
to avoid an ENOSPC failure.
Summary:
- Fix race conditions in the CoW code
- Fix some incorrect input validation checks
- Avoid crashing fs by running out of space when freeing inodes
- Fix toctou race wrt whether or not an inode has an attr
- Fix build error on arm
- Fix page refcount corruption when readahead fails
- Don't corrupt userspace in the bmap ioctl"
* tag 'xfs-for-linus-4.10-rc6-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: prevent quotacheck from overloading inode lru
xfs: fix bmv_count confusion w/ shared extents
xfs: clear _XBF_PAGES from buffers when readahead page
xfs: extsize hints are not unlikely in xfs_bmap_btalloc
xfs: remove racy hasattr check from attr ops
xfs: use per-AG reservations for the finobt
xfs: only update mount/resv fields on success in __xfs_ag_resv_init
xfs: verify dirblocklog correctly
xfs: fix COW writeback race
Linus Torvalds [Fri, 27 Jan 2017 20:41:46 +0000 (12:41 -0800)]
Merge branch 'for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs updates from Chris Mason:
"Some fixes that we've collected from the list.
We still have one more pending to nail down a regression in lzo
compression, but I wanted to get this batch out the door"
* 'for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: remove ->{get, set}_acl() from btrfs_dir_ro_inode_operations
Btrfs: disable xattr operations on subvolume directories
Btrfs: remove old tree_root case in btrfs_read_locked_inode()
Btrfs: fix truncate down when no_holes feature is enabled
Btrfs: Fix deadlock between direct IO and fast fsync
btrfs: fix false enospc error when truncating heavily reflinked file
Linus Torvalds [Fri, 27 Jan 2017 20:36:39 +0000 (12:36 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A set of fixes for this series. This contains:
- Set of fixes for the nvme target code
- A revert of patch from this merge window, causing a regression with
WRITE_SAME on iSCSI targets at least.
- A fix for a use-after-free in the new O_DIRECT bdev code.
- Two fixes for the xen-blkfront driver"
* 'for-linus' of git://git.kernel.dk/linux-block:
Revert "sd: remove __data_len hack for WRITE SAME"
nvme-fc: use blk_rq_nr_phys_segments
nvmet-rdma: Fix missing dma sync to nvme data structures
nvmet: Call fatal_error from keep-alive timout expiration
nvmet: cancel fatal error and flush async work before free controller
nvmet: delete controllers deletion upon subsystem release
nvmet_fc: correct logic in disconnect queue LS handling
block: fix use after free in __blkdev_direct_IO
xen-blkfront: correct maximum segment accounting
xen-blkfront: feature flags handling adjustments
Linus Torvalds [Fri, 27 Jan 2017 20:29:30 +0000 (12:29 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Second round of -rc fixes for 4.10.
This -rc cycle has been slow for the rdma subsystem. I had already
sent you the first batch before the Holiday break. After that, we kept
only getting a few here or there. Up until this week, when I got a
drop of 13 to one driver (qedr). So, here's the -rc patches I have. I
currently have none held in reserve, so unless something new comes in,
this is it until the next merge window opens.
Summary:
- series of iw_cxgb4 fixes to make it work with the drain cq API
- one or two patches each to: srp, iser, cxgb3, vmw_pvrdma, umem,
rxe, and ipoib
- one big series (13 patches) for the new qedr driver"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (27 commits)
RDMA/cma: Fix unknown symbol when CONFIG_IPV6 is not enabled
IB/rxe: Prevent from completer to operate on non valid QP
IB/rxe: Fix rxe dev insertion to rxe_dev_list
IB/umem: Release pid in error and ODP flow
RDMA/qedr: Dispatch port active event from qedr_add
RDMA/qedr: Fix and simplify memory leak in PD alloc
RDMA/qedr: Fix RDMA CM loopback
RDMA/qedr: Fix formatting
RDMA/qedr: Mark three functions as static
RDMA/qedr: Don't reset QP when queues aren't flushed
RDMA/qedr: Don't spam dmesg if QP is in error state
RDMA/qedr: Remove CQ spinlock from CM completion handlers
RDMA/qedr: Return max inline data in QP query result
RDMA/qedr: Return success when not changing QP state
RDMA/qedr: Add uapi header qedr-abi.h
RDMA/qedr: Fix MTU returned from QP query
RDMA/core: Add the function ib_mtu_int_to_enum
IB/vmw_pvrdma: Fix incorrect cleanup on pvrdma_pci_probe error path
IB/vmw_pvrdma: Don't leak info from alloc_ucontext
IB/cxgb3: fix misspelling in header guard
...
Linus Torvalds [Fri, 27 Jan 2017 20:25:26 +0000 (12:25 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Another two bug fixes:
- ptrace partial write information leak
- a guest page hinting regression introduced with v4.6"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: Fix cmma unused transfer from pgste into pte
s390/ptrace: Preserve previous registers for short regset write
Linus Torvalds [Fri, 27 Jan 2017 20:17:07 +0000 (12:17 -0800)]
Merge branch 'stable/for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb
Pull swiotlb fix from Konrad Rzeszutek Wilk:
"An ARM fix in the Xen SWIOTLB - mainly the translation of physical to
bus addresses was done just a tad too late"
* 'stable/for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb-xen: update dev_addr after swapping pages
Linus Torvalds [Fri, 27 Jan 2017 20:10:58 +0000 (12:10 -0800)]
Merge tag 'vfio-v4.10-rc6' of git://github.com/awilliam/linux-vfio
Pull VFIO fix from Alex Williamson:
"mdev IOMMU groups are not yet compatible with the powerpc SPAPR IOMMU
backend, detect and fail group attach (Greg Kurz)"
* tag 'vfio-v4.10-rc6' of git://github.com/awilliam/linux-vfio:
vfio/spapr: fail tce_iommu_attach_group() when iommu_data is null
Jens Axboe [Fri, 27 Jan 2017 18:56:06 +0000 (11:56 -0700)]
Merge branch 'stable/for-jens-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen into for-linus
Konrad writes:
Please pull in your 'for-linus' branch two little fixes for Xen
block front:
One fix is for handling the XEN_PAGE_SIZE != PAGE_SIZE (4KB vs 64KB
on ARM for example) mishandling while the other is fixing
the accounting for the configuration changes.
Vineet Gupta [Fri, 27 Jan 2017 18:45:27 +0000 (10:45 -0800)]
ARC: [arcompact] handle unaligned access delay slot corner case
After emulating an unaligned access in delay slot of a branch, we
pretend as the delay slot never happened - so return back to actual
branch target (or next PC if branch was not taken).
Curently we did this by handling STATUS32.DE, we also need to clear the
BTA.T bit, which is disregarded when returning from original misaligned
exception, but could cause weirdness if it took the interrupt return
path (in case interrupt was acive too)
One ARC700 customer ran into this when enabling unaligned access fixup
for kernel mode accesses as well
Linus Torvalds [Fri, 27 Jan 2017 18:29:33 +0000 (10:29 -0800)]
Merge tag 'media/v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- fix a regression on tvp5150 causing failures at input selection and
image glitches
- CEC was moved out of staging for v4.10. Fix some bugs on it while not
too late
- fix a regression on pctv452e caused by VM stack changes
- fix suspend issued with smiapp
- fix a regression on cobalt driver
- fix some warnings and Kconfig issues with some random configs.
* tag 'media/v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] s5k4ecgx: select CRC32 helper
[media] dvb: avoid warning in dvb_net
[media] v4l: tvp5150: Don't override output pinmuxing at stream on/off time
[media] v4l: tvp5150: Fix comment regarding output pin muxing
[media] v4l: tvp5150: Reset device at probe time, not in get/set format handlers
[media] pctv452e: move buffer to heap, no mutex
[media] media/cobalt: use pci_irq_allocate_vectors
[media] cec: fix race between configuring and unconfiguring
[media] cec: move cec_report_phys_addr into cec_config_thread_func
[media] cec: replace cec_report_features by cec_fill_msg_report_features
[media] cec: update log_addr[] before finishing configuration
[media] cec: CEC_MSG_GIVE_FEATURES should abort for CEC version < 2
[media] cec: when canceling a message, don't overwrite old status info
[media] cec: fix report_current_latency
[media] smiapp: Make suspend and resume functions __maybe_unused
[media] smiapp: Implement power-on and power-off sequences without runtime PM
Linus Torvalds [Fri, 27 Jan 2017 18:22:00 +0000 (10:22 -0800)]
Merge branch 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management fix from Zhang Rui:
"A single revert from a recently introduced problem.
Specifics:
Commit 7611fb68062f ("thermal: thermal_hwmon: Convert to
hwmon_device_register_with_info()"), which was introduced in 4.10-rc5,
uses new hwmon API. But this breaks some soc thermal driver because
the new hwmon API has a strict rule for the hwmon device name. Revert
the offending commit as a quick solution for 4.10"
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
Revert "thermal: thermal_hwmon: Convert to hwmon_device_register_with_info()"
Brian Foster [Thu, 26 Jan 2017 21:18:09 +0000 (13:18 -0800)]
xfs: prevent quotacheck from overloading inode lru
Quotacheck runs at mount time in situations where quota accounting must
be recalculated. In doing so, it uses bulkstat to visit every inode in
the filesystem. Historically, every inode processed during quotacheck
was released and immediately tagged for reclaim because quotacheck runs
before the superblock is marked active by the VFS. In other words,
the final iput() lead to an immediate ->destroy_inode() call, which
allowed the XFS background reclaim worker to start reclaiming inodes.
Commit 17c12bcd3 ("xfs: when replaying bmap operations, don't let
unlinked inodes get reaped") marks the XFS superblock active sooner as
part of the mount process to support caching inodes processed during log
recovery. This occurs before quotacheck and thus means all inodes
processed by quotacheck are inserted to the LRU on release. The
s_umount lock is held until the mount has completed and thus prevents
the shrinkers from operating on the sb. This means that quotacheck can
excessively populate the inode LRU and lead to OOM conditions on systems
without sufficient RAM.
Update the quotacheck bulkstat handler to set XFS_IGET_DONTCACHE on
inodes processed by quotacheck. This causes ->drop_inode() to return 1
and in turn causes iput_final() to evict the inode. This preserves the
original quotacheck behavior and prevents it from overloading the LRU
and running out of memory.
CC: stable@vger.kernel.org # v4.9 Reported-by: Martin Svec <martin.svec@zoner.cz> Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
With some gcc versions, we get a warning about the eicon driver,
and that currently shows up as the only remaining warning in one
of the build bots:
In file included from ../drivers/isdn/hardware/eicon/message.c:30:0:
eicon/message.c: In function 'mixer_notify_update':
eicon/platform.h:333:18: warning: array subscript is above array bounds [-Warray-bounds]
The code is easily changed to open-code the unusual PUT_WORD() line
causing this to avoid the warning.
David S. Miller [Fri, 27 Jan 2017 15:39:10 +0000 (10:39 -0500)]
Merge branch 'gtp-fixes'
Andreas Schultz says:
====================
various gtp fixes
I'm sorry for the compile error mess up in the last version.
It's no excuse for not test compiling, but the hunks got lost in
a rebase.
This is the part of the previous "simple gtp improvements" series
that Pablo indicated should go into net.
The addition of the module alias fixes genl family autoloading,
clearing the DF bit fixes a protocol violation in regard to the
specification and the netns comparison fixes a corner case of
cross netns recv.
v2->v3: fix compiler error introduced in rebase
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Schultz [Fri, 27 Jan 2017 09:40:58 +0000 (10:40 +0100)]
gtp: fix cross netns recv on gtp socket
The use of the passed through netlink src_net to check for a
cross netns operation was wrong. Using the GTP socket and the
GTP netdevice is always correct (even if the netdev has been
moved to new netns after link creation).
Remove the now obsolete net field from gtp_dev.
Signed-off-by: Andreas Schultz <aschultz@tpip.net> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Schultz [Fri, 27 Jan 2017 09:40:57 +0000 (10:40 +0100)]
gtp: clear DF bit on GTP packet tx
3GPP TS 29.281 and 3GPP TS 29.060 imply that GTP-U packets should be
sent with the DF bit cleared. For example 3GPP TS 29.060, Release 8,
Section 13.2.2:
> Backbone router: Any router in the backbone may fragment the GTP
> packet if needed, according to IPv4.
Signed-off-by: Andreas Schultz <aschultz@tpip.net> Acked-by: Harald Welte <laforge@netfilter.org> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Schultz [Fri, 27 Jan 2017 09:40:56 +0000 (10:40 +0100)]
gtp: add genl family modules alias
Auto-load the module when userspace asks for the gtp netlink
family.
Signed-off-by: Andreas Schultz <aschultz@tpip.net> Acked-by: Harald Welte <laforge@netfilter.org> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira [Thu, 26 Jan 2017 21:56:21 +0000 (22:56 +0100)]
tcp: don't annotate mark on control socket from tcp_v6_send_response()
Unlike ipv4, this control socket is shared by all cpus so we cannot use
it as scratchpad area to annotate the mark that we pass to ip6_xmit().
Add a new parameter to ip6_xmit() to indicate the mark. The SCTP socket
family caches the flowi6 structure in the sctp_transport structure, so
we cannot use to carry the mark unless we later on reset it back, which
I discarded since it looks ugly to me.
Fixes: bf99b4ded5f8 ("tcp: fix mark propagation with fwmark_reflect enabled") Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
arm64: skip register_cpufreq_notifier on ACPI-based systems
On ACPI based systems where the topology is setup using the API
store_cpu_topology, at the moment we do not have necessary code
to parse cpu capacity and handle cpufreq notifier, thus
resulting in a kernel panic.
Linus Torvalds [Fri, 27 Jan 2017 02:04:56 +0000 (18:04 -0800)]
Merge tag 'drm-fixes-for-v4.10-rc6-part-two' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"This is the main request for rc6, since really the one earlier was the
rc5 one :-)
The main thing are the nouveau specific race fixes for the connector
locking bug we fixed in -next and reverted here as it has quite large
prereqs. These two fixes should solve the problem at that level and we
can fix it properly in 4.11
Otherwise i915 has a bunch of changes, one ABI change for GVT related
stuff, some VC4 leak fixes, one core fence fix and some AMD changes,
oh and one ast hang avoidance fix.
Hoping it calms down around now"
* tag 'drm-fixes-for-v4.10-rc6-part-two' of git://people.freedesktop.org/~airlied/linux: (25 commits)
drm/nouveau: Handle fbcon suspend/resume in seperate worker
drm/nouveau: Don't enabling polling twice on runtime resume
drm/ast: Fixed system hanged if disable P2A
Revert "drm/radeon: always apply pci shutdown callbacks"
drm/i915: reinstate call to trace_i915_vma_bind
drm/i915: Move atomic state free from out of fence release
drm/i915: Check for NULL atomic state in intel_crtc_disable_noatomic()
drm/i915: Fix calculation of rotated x and y offsets for planar formats
drm/i915: Don't init hpd polling for vlv and chv from runtime_suspend()
drm/i915: Don't leak edid in intel_crt_detect_ddc()
drm/i915: Release temporary load-detect state upon switching
drm/i915: prevent crash with .disable_display parameter
drm/i915: Avoid drm_atomic_state_put(NULL) in intel_display_resume
MAINTAINERS: update new mail list for intel gvt driver
drm/i915/gvt: Fix kmem_cache_create() name
drm/i915/gvt/kvmgt: mdev ABI is available_instances, not available_instance
drm/amdgpu: fix unload driver issue for virtual display
drm/amdgpu: check ring being ready before using
drm/vc4: Return -EINVAL on the overflow checks failing.
drm/vc4: Fix an integer overflow in temporary allocation layout.
...
Dave Airlie [Fri, 27 Jan 2017 01:29:44 +0000 (11:29 +1000)]
Merge tag 'drm-intel-fixes-2017-01-26' of git://anongit.freedesktop.org/git/drm-intel into drm-fixes
More fixes than I'd like at this stage, but I think the holidays and
conferences have delayed finding and fixing the stuff a bit. Almost all
of them have Fixes: tags, so it's not just random fixes, we can point
fingers at the commits that broke stuff.
There's an ABI fix to GVT from Alex, before we go on an release a kernel
with the wrong attribute name.
* tag 'drm-intel-fixes-2017-01-26' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: reinstate call to trace_i915_vma_bind
drm/i915: Move atomic state free from out of fence release
drm/i915: Check for NULL atomic state in intel_crtc_disable_noatomic()
drm/i915: Fix calculation of rotated x and y offsets for planar formats
drm/i915: Don't init hpd polling for vlv and chv from runtime_suspend()
drm/i915: Don't leak edid in intel_crt_detect_ddc()
drm/i915: Release temporary load-detect state upon switching
drm/i915: prevent crash with .disable_display parameter
drm/i915: Avoid drm_atomic_state_put(NULL) in intel_display_resume
MAINTAINERS: update new mail list for intel gvt driver
drm/i915/gvt: Fix kmem_cache_create() name
drm/i915/gvt/kvmgt: mdev ABI is available_instances, not available_instance
drm/i915/gvt: Fix relocation of shadow bb
drm/i915/gvt: Enable the shadow batch buffer
Linus Torvalds [Fri, 27 Jan 2017 01:27:00 +0000 (17:27 -0800)]
Merge tag 'acpi-4.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix two regressions introduced recently, one by reverting the
problematic commit and one by fixing up locking in the ACPICA core.
Specifics:
- Revert a recent change that added an ACPI video blacklist entry for
HP Pavilion dv6 as it turned to introduce backlight handling
regressions on some systems (Hans de Goede).
- Fix locking in the ACPICA core to avoid deadlocks related to table
loading that were exposed by a recent change in that area (Lv
Zheng)"
* tag 'acpi-4.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI / video: Add force_native quirk for HP Pavilion dv6"
ACPICA: Tables: Fix hidden logic related to acpi_tb_install_standard_table()
Linus Torvalds [Fri, 27 Jan 2017 01:14:17 +0000 (17:14 -0800)]
Merge tag 'pm-4.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix two regressions introduced recently, one by reverting the
problematic commit and one by fixing up the behavior in an overlooked
case.
Specifics:
- Revert the recent change that caused suspend-to-idle to be used as
the default suspend method on systems where it is indicated to be
efficient by the ACPI tables, as that turned out to be premature
and introduced suspend regressions on some systems with missing
power management support in device drivers (Rafael Wysocki).
- Fix up the intel_pstate driver to take changes of the global limits
via sysfs correctly when the performance policy is used which has
been broken by a recent change in it (Srinivas Pandruvada)"
* tag 'pm-4.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Fix sysfs limits enforcement for performance policy
Revert "PM / sleep / ACPI: Use the ACPI_FADT_LOW_POWER_S0 flag"
Lyude Paul [Thu, 12 Jan 2017 02:25:24 +0000 (21:25 -0500)]
drm/nouveau: Handle fbcon suspend/resume in seperate worker
Resuming from RPM can happen while already holding
dev->mode_config.mutex. This means we can't actually handle fbcon in
any RPM resume workers, since restoring fbcon requires grabbing
dev->mode_config.mutex again. So move the fbcon suspend/resume code into
it's own worker, and rely on that instead to avoid deadlocking.
This fixes more deadlocks for runtime suspending the GPU on the ThinkPad
W541. Reproduction recipe:
- Get a machine with both optimus and a nvidia card with connectors
attached to it
- Wait for the nvidia GPU to suspend
- Attempt to manually reprobe any of the connectors on the nvidia GPU
using sysfs
- *deadlock*
[airlied: use READ_ONCE to address Hans's comment]
Signed-off-by: Lyude <lyude@redhat.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Kilian Singer <kilian.singer@quantumtechnology.info> Cc: Lukas Wunner <lukas@wunner.de> Cc: David Airlie <airlied@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Lyude Paul [Thu, 12 Jan 2017 02:25:23 +0000 (21:25 -0500)]
drm/nouveau: Don't enabling polling twice on runtime resume
As it turns out, on cards that actually have CRTCs on them we're already
calling drm_kms_helper_poll_enable(drm_dev) from
nouveau_display_resume() before we call it in
nouveau_pmops_runtime_resume(). This leads us to accidentally trying to
enable polling twice, which results in a potential deadlock between the
RPM locks and drm_dev->mode_config.mutex if we end up trying to enable
polling the second time while output_poll_execute is running and holding
the mode_config lock. As such, make sure we only enable polling in
nouveau_pmops_runtime_resume() if we need to.
This fixes hangs observed on the ThinkPad W541
Signed-off-by: Lyude <lyude@redhat.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Kilian Singer <kilian.singer@quantumtechnology.info> Cc: Lukas Wunner <lukas@wunner.de> Cc: David Airlie <airlied@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Y.C. Chen [Thu, 26 Jan 2017 01:45:40 +0000 (09:45 +0800)]
drm/ast: Fixed system hanged if disable P2A
The original ast driver will access some BMC configuration through P2A bridge
that can be disabled since AST2300 and after.
It will cause system hanged if P2A bridge is disabled.
Here is the update to fix it.
Signed-off-by: Y.C. Chen <yc_chen@aspeedtech.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 27 Jan 2017 00:33:39 +0000 (10:33 +1000)]
Merge tag 'drm-vc4-fixes-2017-01-23' of https://github.com/anholt/linux into drm-fixes
This pull request brings in a few little error checking fixes and one
slow memory leak fix.
* tag 'drm-vc4-fixes-2017-01-23' of https://github.com/anholt/linux:
drm/vc4: Return -EINVAL on the overflow checks failing.
drm/vc4: Fix an integer overflow in temporary allocation layout.
drm/vc4: fix a bounds check
drm/vc4: Fix memory leak of the CRTC state.
Dave Airlie [Fri, 27 Jan 2017 00:17:43 +0000 (10:17 +1000)]
Merge branch 'drm-fixes-4.10' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Just a few small fixes.
* 'drm-fixes-4.10' of git://people.freedesktop.org/~agd5f/linux:
Revert "drm/radeon: always apply pci shutdown callbacks"
drm/amdgpu: fix unload driver issue for virtual display
drm/amdgpu: check ring being ready before using
Dave Airlie [Fri, 27 Jan 2017 00:16:56 +0000 (10:16 +1000)]
Merge tag 'drm-misc-fixes-2017-01-23' of git://anongit.freedesktop.org/git/drm-misc into drm-fixes
Single fence fix.
* tag 'drm-misc-fixes-2017-01-23' of git://anongit.freedesktop.org/git/drm-misc:
drm/fence: fix memory overwrite when setting out_fence fd
Omar Sandoval [Thu, 26 Jan 2017 01:06:39 +0000 (17:06 -0800)]
Btrfs: disable xattr operations on subvolume directories
When you snapshot a subvolume containing a subvolume, you get a
placeholder directory where the subvolume would be. These directory
inodes have ->i_ops set to btrfs_dir_ro_inode_operations. Previously,
these i_ops didn't include the xattr operation callbacks. The conversion
to xattr_handlers missed this case, leading to bogus attempts to set
xattrs on these inodes. This manifested itself as failures when running
delayed inodes.
To fix this, clear IOP_XATTR in ->i_opflags on these inodes.
Fixes: 6c6ef9f26e59 ("xattr: Stop calling {get,set,remove}xattr inode operations") Cc: Andreas Gruenbacher <agruenba@redhat.com> Reported-by: Chris Murphy <lists@colorremedies.com> Tested-by: Chris Murphy <lists@colorremedies.com> Cc: <stable@vger.kernel.org> # 4.9.x Signed-off-by: Omar Sandoval <osandov@fb.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: Chris Mason <clm@fb.com>
Omar Sandoval [Thu, 26 Jan 2017 01:06:38 +0000 (17:06 -0800)]
Btrfs: remove old tree_root case in btrfs_read_locked_inode()
As Jeff explained in c2951f32d36c ("btrfs: remove old tree_root dirent
processing in btrfs_real_readdir()"), supporting this old format is no
longer necessary since the Btrfs magic number has been updated since we
changed to the current format. There are other places where we still
handle this old format, but since this is part of a fix that is going to
stable, I'm only removing this one for now.
Cc: <stable@vger.kernel.org> # 4.9.x Signed-off-by: Omar Sandoval <osandov@fb.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: Chris Mason <clm@fb.com>
Kazuya Mizuguchi [Thu, 26 Jan 2017 13:29:27 +0000 (14:29 +0100)]
ravb: unmap descriptors when freeing rings
"swiotlb buffer is full" errors occur after repeated initialisation of a
device - f.e. suspend/resume or ip link set up/down. This is because memory
mapped using dma_map_single() in ravb_ring_format() and ravb_start_xmit()
is not released. Resolve this problem by unmapping descriptors when
freeing rings.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper") Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[simon: reworked] Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Trond Myklebust [Thu, 26 Jan 2017 20:50:41 +0000 (15:50 -0500)]
pNFS: Fix a reference leak in _pnfs_return_layout
IF NFS_LAYOUT_RETURN_REQUESTED is not set, then we currently exit
without freeing the list of invalidated layout segments, leading
to a reference leak.
Reported-by: Olga Kornievskaia <aglo@umich.edu> Fixes: 24408f5282 ("pNFS: Fix bugs in _pnfs_return_layout") Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Chuck Lever [Thu, 26 Jan 2017 20:14:52 +0000 (15:14 -0500)]
nfs: Fix "Don't increment lock sequence ID after NFS4ERR_MOVED"
Lock sequence IDs are bumped in decode_lock by calling
nfs_increment_seqid(). nfs_increment_sequid() does not use the
seqid_mutating_err() function fixed in commit 059aa7348241 ("Don't
increment lock sequence ID after NFS4ERR_MOVED").
Fixes: 059aa7348241 ("Don't increment lock sequence ID after ...") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Tested-by: Xuan Qi <xuan.qi@oracle.com> Cc: stable@vger.kernel.org # v3.7+ Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
The following patchset contains a large batch with Netfilter fixes for
your net tree, they are:
1) Two patches to solve conntrack garbage collector cpu hogging, one to
remove GC_MAX_EVICTS and another to look at the ratio (scanned entries
vs. evicted entries) to make a decision on whether to reduce or not
the scanning interval. From Florian Westphal.
2) Two patches to fix incorrect set element counting if NLM_F_EXCL is
is not set. Moreover, don't decrenent set->nelems from abort patch
if -ENFILE which leaks a spare slot in the set. This includes a
patch to deconstify the set walk callback to update set->ndeact.
3) Two fixes for the fwmark_reflect sysctl feature: Propagate mark to
reply packets both from nf_reject and local stack, from Pau Espin Pedrol.
4) Fix incorrect handling of loopback traffic in rpfilter and nf_tables
fib expression, from Liping Zhang.
5) Fix oops on stateful objects netlink dump, when no filter is specified.
Also from Liping Zhang.
6) Fix a build error if proc is not available in ipt_CLUSTERIP, related
to fix that was applied in the previous batch for net. From Arnd Bergmann.
7) Fix lack of string validation in table, chain, set and stateful
object names in nf_tables, from Liping Zhang. Moreover, restrict
maximum log prefix length to 127 bytes, otherwise explicitly bail
out.
8) Two patches to fix spelling and typos in nf_tables uapi header file
and Kconfig, patches from Alexander Alemayhu and William Breathitt Gray.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Darrick J. Wong [Thu, 26 Jan 2017 17:50:30 +0000 (09:50 -0800)]
xfs: fix bmv_count confusion w/ shared extents
In a bmapx call, bmv_count is the total size of the array, including the
zeroth element that userspace uses to supply the search key. The output
array starts at offset 1 so that we can set up the user for the next
invocation. Since we now can split an extent into multiple bmap records
due to shared/unshared status, we have to be careful that we don't
overflow the output array.
In the original patch f86f403794b ("xfs: teach get_bmapx about shared
extents and the CoW fork") I used cur_ext (the output index) to check
for overflows, albeit with an off-by-one error. Since nexleft no longer
describes the number of unfilled slots in the output, we can rip all
that out and use cur_ext for the overflow check directly.
Failure to do this causes heap corruption in bmapx callers such as
xfs_io and xfs_scrub. xfs/328 can reproduce this problem.
Reviewed-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Linus Torvalds [Thu, 26 Jan 2017 17:08:49 +0000 (09:08 -0800)]
Merge tag 'pinctrl-v4.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"A bunch of pin control fixes for v4.10 that didn't get sent off until
now, sorry for the delay.
It's only driver fixes:
- A bunch of fixes to the Intel drivers: broxton, baytrail. Bugs
related to register offsets, IRQ, debounce functionality.
- Fix a conflict amongst UART settings on the meson.
- Fix the ethernet setting on the Uniphier.
- A compilation warning squelched"
* tag 'pinctrl-v4.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: uniphier: fix Ethernet (RMII) pin-mux setting for LD20
pinctrl: meson: fix uart_ao_b for GXBB and GXL/GXM
pinctrl: amd: avoid maybe-uninitalized warning
pinctrl: baytrail: Do not add all GPIOs to IRQ domain
pinctrl: baytrail: Rectify debounce support
pinctrl: intel: Set pin direction properly
pinctrl: broxton: Use correct PADCFGLOCK offset
Bart Van Assche [Wed, 25 Jan 2017 21:43:56 +0000 (13:43 -0800)]
Revert "sd: remove __data_len hack for WRITE SAME"
This patch reverts commit f80de881d8df and avoids that sending a
WRITE SAME command to the iSCSI initiator triggers the following:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000014
TARGET_CORE[iSCSI]: Expected Transfer Length: 260096 does not match SCSI CDB Length: 512 for SAM Opcode: 0x41
IP: iscsi_tcp_segment_done+0x20b/0x310 [libiscsi_tcp]
Linus Torvalds [Thu, 26 Jan 2017 16:55:33 +0000 (08:55 -0800)]
Merge tag 'drm-fixes-for-v4.10-rc6-revert-one' of git://people.freedesktop.org/~airlied/linux
Pull drm revert from Dave Airlie:
"Revert one patch missing some prereqs.
One of the connector fixes was missing some prereqs, we have an
alternate driver fix that should work that I'll send tomorrow.
Today is a holiday here so quickly smashing this out"
Daniel Vetter explains:
"I pushed a locking change to fix a nouveau rpm issue to -fixes that
needed the connector_list rework. And that's only in -next, but I
missed that. Dave has the revert in a pull, and he'll follow-up with
the hack nouveau patch for 4.10, and then we'll reapply the proper fix
again for -next and revert the hacks. A bit a mess, but should be
sorted soon"
* tag 'drm-fixes-for-v4.10-rc6-revert-one' of git://people.freedesktop.org/~airlied/linux:
Revert "drm/probe-helpers: Drop locking from poll_enable"
Parav Pandit [Thu, 19 Jan 2017 15:55:08 +0000 (09:55 -0600)]
nvmet-rdma: Fix missing dma sync to nvme data structures
This patch performs dma sync operations on nvme_command
and nvme_completion.
nvme_command is synced
(a) on receiving of the recv queue completion for cpu access.
(b) before posting recv wqe back to rdma adapter for device access.
nvme_completion is synced
(a) on receiving of the recv queue completion of associated
nvme_command for cpu access.
(b) before posting send wqe to rdma adapter for device access.
This patch is generated for git://git.infradead.org/nvme-fabrics.git
Branch: nvmf-4.10
Signed-off-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Sagi Grimberg [Sun, 1 Jan 2017 11:18:26 +0000 (13:18 +0200)]
nvmet: Call fatal_error from keep-alive timout expiration
We only need to call delete_ctrl once, so given that both
keep-alive timeout and any other fatal error can trigger it,
just make sure we only call delete_ctrl once.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Christoph Hellwig <hch@lst.de>
Sagi Grimberg [Sun, 27 Nov 2016 20:29:17 +0000 (22:29 +0200)]
nvmet: delete controllers deletion upon subsystem release
No reason for them to be kept around if we are
deleting the subsystem, so instead of passively
wait for the host to disconnect, actively delete
the controllers.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
projects / mirror_ubuntu-kernels.git / log