Taehee Yoo [Mon, 26 Nov 2018 11:03:30 +0000 (20:03 +0900)]
netfilter: nf_tables: fix suspicious RCU usage in nft_chain_stats_replace()
basechain->stats is rcu protected data which is updated from
nft_chain_stats_replace(). This function is executed from the commit
phase which holds the pernet nf_tables commit mutex - not the global
nfnetlink subsystem mutex.
Test commands to reproduce the problem are:
%iptables-nft -I INPUT
%iptables-nft -Z
%iptables-nft -Z
This patch uses RCU calls to handle basechain->stats updates to fix a
splat that looks like:
Thomas Falcon [Fri, 30 Nov 2018 16:59:08 +0000 (10:59 -0600)]
net/ibmvnic: Fix RTNL deadlock during device reset
Commit a5681e20b541 ("net/ibmnvic: Fix deadlock problem
in reset") made the change to hold the RTNL lock during
driver reset but still calls netdev_notify_peers, which
results in a deadlock. Instead, use call_netdevice_notifiers,
which is functionally the same except that it does not
take the RTNL lock again.
Fixes: a5681e20b541 ("net/ibmnvic: Fix deadlock problem in reset") Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 78139c94dc8c ("net: vhost: lock the vqs one by one") moved the vq
lock to improve scalability, but introduced a possible deadlock in
vhost-iotlb. vhost_iotlb_notify_vq() now takes vq->mutex while holding
the device's IOTLB spinlock. And on the vhost_iotlb_miss() path, the
spinlock is taken while holding vq->mutex.
Since calling vhost_poll_queue() doesn't require any lock, avoid the
deadlock by not taking vq->mutex.
Fixes: 78139c94dc8c ("net: vhost: lock the vqs one by one") Acked-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch set is for R-Car Gen3 Salvator-XS boards. If we do
the following method, the phy cannot link up correctly.
1) Kernel boots by using initramfs.
--> No open the nic, so phy_device_register() and phy_probe()
deasserts the reset.
2) Kernel enters the suspend.
--> So, keep the reset signal as deassert.
--> On R-Car Salvator-XS board, unfortunately, the board power is
turned off.
3) Kernel returns from suspend.
4) ifconfig eth0 up
--> Then, since edge signal of the reset doesn't happen,
it cannot link up.
5) ifconfig eth0 down
6) ifconfig eth0 up
--> In this case, it can link up.
When resolving this issue after I got feedback from Andrew and Heiner,
I found an issue that the phy_device.c didn't call phy_resume()
if the PHY was not attached. So, patch 1 fixes it and add toggling
the phy reset to the micrel phy driver.
Changes from v1 (as RFC):
- No remove the current code of phy_device.c to avoid any side effects.
- Fix the mdio_bus_phy_resume() in phy_device.c.
- Add toggling the phy reset in micrel.c if the PHY is not attached.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: micrel: add toggling phy reset if PHY is not attached
This patch adds toggling phy reset if PHY is not attached. Otherwise,
some boards (e.g. R-Car H3 Salvator-XS) cannot link up correctly if
we do the following method:
1) Kernel boots by using initramfs.
--> No open the nic, so phy_device_register() and phy_probe()
deasserts the reset.
2) Kernel enters the suspend.
--> So, keep the reset signal as deassert.
--> On R-Car Salvator-XS board, unfortunately, the board power is
turned off.
3) Kernel returns from suspend.
4) ifconfig eth0 up
--> Then, since edge signal of the reset doesn't happen,
it cannot link up.
5) ifconfig eth0 down
6) ifconfig eth0 up
--> In this case, it can link up.
Reported-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: Fix not to call phy_resume() if PHY is not attached
This patch fixes an issue that mdio_bus_phy_resume() doesn't call
phy_resume() if the PHY is not attached.
Fixes: 803dd9c77ac3 ("net: phy: avoid suspending twice a PHY") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Prashant Bhole [Mon, 3 Dec 2018 09:09:24 +0000 (18:09 +0900)]
tun: remove skb access after netif_receive_skb
In tun.c skb->len was accessed while doing stats accounting after a
call to netif_receive_skb. We can not access skb after this call
because buffers may be dropped.
The fix for this bug would be to store skb->len in local variable and
then use it after netif_receive_skb(). IMO using xdp data size for
accounting bytes will be better because input for tun_xdp_one() is
xdp_buff.
Hence this patch:
- fixes a bug by removing skb access after netif_receive_skb()
- uses xdp data size for accounting bytes
Fixes: 043d222f93ab ("tuntap: accept an array of XDP buffs through sendmsg()") Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp> Acked-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It's not the same as in 7fe0ee09 patch described.
As 8139cp uses shared irq mode, other device irq will trigger
cp_interrupt to execute.
cp_change_mtu
-> cp_close
-> cp_open
In cp_close routine just before free_irq(), some interrupt may occur.
In my environment, cp_interrupt exectutes and IntrStatus is 0x4,
exactly TxOk. That will cause cp_tx to wake device queue.
As device queue is started, cp_start_xmit and cp_open will run at same
time which will cause kernel BUG.
For example:
[#] for tx descriptor
At start:
[#][#][#]
num_queued=3
After cp_init_hw->cp_start_hw->netdev_reset_queue:
[#][#][#]
num_queued=0
When 8139cp starts to work then cp_tx will check
num_queued mismatchs the complete_bytes.
The patch will check IntrMask before check IntrStatus in cp_interrupt.
When 8139cp interrupt is disabled, just return.
Signed-off-by: Su Yanjun <suyj.fnst@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 3 Dec 2018 07:19:33 +0000 (08:19 +0100)]
net: phy: don't allow __set_phy_supported to add unsupported modes
Currently __set_phy_supported allows to add modes w/o checking whether
the PHY supports them. This is wrong, it should never add modes but
only remove modes we don't want to support.
The commit marked as fixed didn't do anything wrong, it just copied
existing functionality to the helper which is being fixed now.
Fixes: f3a6bd393c2c ("phylib: Add phy_set_max_speed helper") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 29 Nov 2018 13:45:39 +0000 (14:45 +0100)]
tun: forbid iface creation with rtnl ops
It's not supported right now (the goal of the initial patch was to support
'ip link del' only).
Before the patch:
$ ip link add foo type tun
[ 239.632660] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
[snip]
[ 239.636410] RIP: 0010:register_netdevice+0x8e/0x3a0
This panic occurs because dev->netdev_ops is not set by tun_setup(). But to
have something usable, it will require more than just setting
netdev_ops.
Fixes: f019a7a594d9 ("tun: Implement ip link del tunXXX") CC: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Thu, 29 Nov 2018 05:53:16 +0000 (13:53 +0800)]
virtio-net: keep vnet header zeroed after processing XDP
We copy vnet header unconditionally in page_to_skb() this is wrong
since XDP may modify the packet data. So let's keep a zeroed vnet
header for not confusing the conversion between vnet header and skb
metadata.
In the future, we should able to detect whether or not the packet was
modified and keep using the vnet header when packet was not touched.
Fixes: f600b6905015 ("virtio_net: Add XDP support") Reported-by: Pavel Popa <pashinho1990@gmail.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Thu, 29 Nov 2018 00:06:45 +0000 (16:06 -0800)]
tcp: fix SNMP TCP timeout under-estimation
Previously the SNMP TCPTIMEOUTS counter has inconsistent accounting:
1. It counts all SYN and SYN-ACK timeouts
2. It counts timeouts in other states except recurring timeouts and
timeouts after fast recovery or disorder state.
Such selective accounting makes analysis difficult and complicated. For
example the monitoring system needs to collect many other SNMP counters
to infer the total amount of timeout events. This patch makes TCPTIMEOUTS
counter simply counts all the retransmit timeout (SYN or data or FIN).
Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Thu, 29 Nov 2018 00:06:44 +0000 (16:06 -0800)]
tcp: fix SNMP under-estimation on failed retransmission
Previously the SNMP counter LINUX_MIB_TCPRETRANSFAIL is not counting
the TSO/GSO properly on failed retransmission. This patch fixes that.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Thu, 29 Nov 2018 00:06:43 +0000 (16:06 -0800)]
tcp: fix off-by-one bug on aborting window-probing socket
Previously there is an off-by-one bug on determining when to abort
a stalled window-probing socket. This patch fixes that so it is
consistent with tcp_write_timeout().
Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pan Bian [Wed, 28 Nov 2018 23:54:22 +0000 (07:54 +0800)]
liquidio: read sc->iq_no before release sc
The function lio_vf_rep_packet_sent_callback releases the occupation of
sc via octeon_free_soft_command. sc should not be used after that.
Unfortunately, sc->iq_no is read. To fix this, the patch stores sc->iq_no
into a local variable before releasing sc and then uses the local variable
instead of sc->iq_no.
Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Wed, 28 Nov 2018 23:04:05 +0000 (15:04 -0800)]
mlx5: fix get_ip_proto()
IP header is not necessarily located right after struct ethhdr,
there could be multiple 802.1Q headers in between, this is why
we call __vlan_get_protocol().
Fixes: fe1dc069990c ("net/mlx5e: don't set CHECKSUM_COMPLETE on SCTP packets") Cc: Alaa Hleihel <alaa@mellanox.com> Cc: Or Gerlitz <ogerlitz@mellanox.com> Cc: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Acked-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 28 Nov 2018 21:40:04 +0000 (13:40 -0800)]
net: dsa: Fix tagging attribute location
While introducing the DSA tagging protocol attribute, it was added to the DSA
slave network devices, but those actually see untagged traffic (that is their
whole purpose). Correct this mistake by putting the tagging sysfs attribute
under the DSA master network device where this is the information that we need.
While at it, also correct the sysfs documentation mistake that missed the
"dsa/" directory component of the attribute.
Fixes: 98cdb4807123 ("net: dsa: Expose tagging protocol to user-space") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Wed, 28 Nov 2018 17:43:42 +0000 (18:43 +0100)]
net/sched: act_police: fix memory leak in case of invalid control action
when users set an invalid control action, kmemleak complains as follows:
# echo clear >/sys/kernel/debug/kmemleak
# ./tdc.py -e b48b
Test b48b: Add police action with exceed goto chain control action
All test results:
1..1
ok 1 - b48b # Add police action with exceed goto chain control action
about to flush the tap output if tests need to be skipped
done flushing skipped test tap output
# echo scan >/sys/kernel/debug/kmemleak
# cat /sys/kernel/debug/kmemleak
unreferenced object 0xffffa0fafbc3dde0 (size 96):
comm "tc", pid 2358, jiffies 4294922738 (age 17.022s)
hex dump (first 32 bytes):
2a 00 00 20 00 00 00 00 00 00 7d 00 00 00 00 00 *.. ......}.....
f8 07 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000648803d2>] tcf_action_init_1+0x384/0x4c0
[<00000000cb69382e>] tcf_action_init+0x12b/0x1a0
[<00000000847ef0d4>] tcf_action_add+0x73/0x170
[<0000000093656e14>] tc_ctl_action+0x122/0x160
[<0000000023c98e32>] rtnetlink_rcv_msg+0x263/0x2d0
[<000000003493ae9c>] netlink_rcv_skb+0x4d/0x130
[<00000000de63f8ba>] netlink_unicast+0x209/0x2d0
[<00000000c3da0ebe>] netlink_sendmsg+0x2c1/0x3c0
[<000000007a9e0753>] sock_sendmsg+0x33/0x40
[<00000000457c6d2e>] ___sys_sendmsg+0x2a0/0x2f0
[<00000000c5c6a086>] __sys_sendmsg+0x5e/0xa0
[<00000000446eafce>] do_syscall_64+0x5b/0x180
[<000000004aa871f2>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[<00000000450c38ef>] 0xffffffffffffffff
change tcf_police_init() to avoid leaking 'new' in case TCA_POLICE_RESULT
contains TC_ACT_GOTO_CHAIN extended action.
Fixes: c08f5ed5d625 ("net/sched: act_police: disallow 'goto chain' on fallback control action") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley [Tue, 27 Nov 2018 22:04:12 +0000 (14:04 -0800)]
nfp: flower: prevent offload if rhashtable insert fails
For flow offload adds, if the rhash insert code fails, the flow will still
have been offloaded but the reference to it in the driver freed.
Re-order the offload setup calls to ensure that a flow will only be written
to FW if a kernel reference is held and stored in the rhashtable. Remove
this hashtable entry if the offload fails.
Fixes: c01d0efa5136 ("nfp: flower: use rhashtable for flow caching") Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley [Tue, 27 Nov 2018 22:04:11 +0000 (14:04 -0800)]
nfp: flower: release metadata on offload failure
Calling nfp_compile_flow_metadata both assigns a stats context and
increments a ref counter on (or allocates) a mask id table entry. These
are released by the nfp_modify_flow_metadata call on flow deletion,
however, if a flow add fails after metadata is set then the flow entry
will be deleted but the metadata assignments leaked.
Add an error path to the flow add offload function to ensure allocated
metadata is released in the event of an offload fail.
Fixes: 81f3ddf2547d ("nfp: add control message passing capabilities to flower offloads") Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Toni Peltonen [Tue, 27 Nov 2018 14:56:57 +0000 (16:56 +0200)]
bonding: fix 802.3ad state sent to partner when unbinding slave
Previously when unbinding a slave the 802.3ad implementation only told
partner that the port is not suitable for aggregation by setting the port
aggregation state from aggregatable to individual. This is not enough. If the
physical layer still stays up and we only unbinded this port from the bond there
is nothing in the aggregation status alone to prevent the partner from sending
traffic towards us. To ensure that the partner doesn't consider this
port at all anymore we should also disable collecting and distributing to
signal that this actor is going away. Also clear AD_STATE_SYNCHRONIZATION to
ensure partner exits collecting + distributing state.
I have tested this behaviour againts Arista EOS switches with mlx5 cards
(physical link stays up even when interface is down) and simulated
the same situation virtually Linux <-> Linux with two network namespaces
running two veth device pairs. In both cases setting aggregation to
individual doesn't alone prevent traffic from being to sent towards this
port given that the link stays up in partners end. Partner still keeps
it's end in collecting + distributing state and continues until timeout is
reached. In most cases this means we are losing the traffic partner sends
towards our port while we wait for timeout. This is most visible with slow
periodic time (LACP rate slow).
Other open source implementations like Open VSwitch and libreswitch, and
vendor implementations like Arista EOS, seem to disable collecting +
distributing to when doing similar port disabling/detaching/removing change.
With this patch kernel implementation would behave the same way and ensure
partner doesn't consider our actor viable anymore.
Signed-off-by: Toni Peltonen <peltzi@peltzi.fi> Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com> Acked-by: Jonathan Toppins <jtoppins@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bogdanov [Tue, 27 Nov 2018 14:51:17 +0000 (14:51 +0000)]
net: aquantia: fix rx checksum offload bits
The last set of csum offload fixes had a leak:
Checksum enabled status bits from rx descriptor were incorrectly
interpreted. Consequently all the other valid logic worked on zero bits.
That caused rx checksum offloads never to trigger.
Tested by dumping rx descriptors and validating resulting csum_level.
Reported-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Fixes: ad703c2b9127f ("net: aquantia: invalid checksumm offload implementation") Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a net_warn_ratelimited message, fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The imbalance happens because the driver creates the debugfs hierarchy
when the device is opened and tears it down when the device is closed.
There's little gain in that, and it could be argued that it is even
surprising because it's not usually done for other devices. Fix the
imbalance by moving the debugfs creation and teardown to the driver's
->probe() and ->remove() implementations instead.
Note that the ring descriptors cannot be read while the interface is
down, so make sure to return an empty file when the descriptors_status
debugfs file is read.
Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Tue, 27 Nov 2018 11:11:50 +0000 (19:11 +0800)]
sctp: update frag_point when stream_interleave is set
sctp_assoc_update_frag_point() should be called whenever asoc->pathmtu
changes, but we missed one place in sctp_association_init(). It would
cause frag_point is zero when sending data.
As says in Jakub's reproducer, if sp->pathmtu is set by socketopt, the
new asoc->pathmtu inherits it in sctp_association_init(). Later when
transports are added and their pmtu >= asoc->pathmtu, it will never
call sctp_assoc_update_frag_point() to set frag_point.
This patch is to fix it by updating frag_point after asoc->pathmtu is
set as sp->pathmtu in sctp_association_init(). Note that it moved them
after sctp_stream_init(), as stream->si needs to be set first.
Frag_point's calculation is also related with datachunk's type, so it
needs to update frag_point when stream->si may be changed in
sctp_process_init().
v1->v2:
- call sctp_assoc_update_frag_point() separately in sctp_process_init
and sctp_association_init, per Marcelo's suggestion.
Fixes: 2f5e3c9df693 ("sctp: introduce sctp_assoc_update_frag_point") Reported-by: Jakub Audykowicz <jakub.audykowicz@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Paasch [Fri, 30 Nov 2018 00:01:04 +0000 (16:01 -0800)]
net: Prevent invalid access to skb->prev in __qdisc_drop_all
__qdisc_drop_all() accesses skb->prev to get to the tail of the
segment-list.
With commit 68d2f84a1368 ("net: gro: properly remove skb from list")
the skb-list handling has been changed to set skb->next to NULL and set
the list-poison on skb->prev.
With that change, __qdisc_drop_all() will panic when it tries to
dereference skb->prev.
Since commit 992cba7e276d ("net: Add and use skb_list_del_init().")
__list_del_entry is used, leaving skb->prev unchanged (thus,
pointing to the list-head if it's the first skb of the list).
This will make __qdisc_drop_all modify the next-pointer of the list-head
and result in a panic later on:
This patch makes sure that skb->prev is set to NULL when entering
netem_enqueue.
Cc: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp> Cc: Tyler Hicks <tyhicks@canonical.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Fixes: 68d2f84a1368 ("net: gro: properly remove skb from list") Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Christoph Paasch <cpaasch@apple.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Schiller [Tue, 27 Nov 2018 08:50:29 +0000 (09:50 +0100)]
net/x25: handle call collisions
If a session in X25_STATE_1 (Awaiting Call Accept) receives a call
request, the session will be closed (x25_disconnect), cause=0x01
(Number Busy) and diag=0x48 (Call Collision) will be set and a clear
request will be send.
Signed-off-by: Martin Schiller <ms@dev.tdt.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Schiller [Tue, 27 Nov 2018 08:50:28 +0000 (09:50 +0100)]
net/x25: fix null_x25_address handling
o x25_find_listener(): the compare for the null_x25_address was wrong.
We have to check the x25_addr of the listener socket instead of the
x25_addr of the incomming call.
o x25_bind(): it was not possible to bind a socket to null_x25_address
Signed-off-by: Martin Schiller <ms@dev.tdt.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Baruch Siach [Thu, 29 Nov 2018 10:00:05 +0000 (12:00 +0200)]
net: phy: sfp: correct location of SFP standards
SFP standards are now available from the SNIA (Storage Networking
Industry Association) website.
Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 29 Nov 2018 19:06:09 +0000 (11:06 -0800)]
Merge branch 'xps-fixes'
Sabrina Dubroca says:
====================
fixes for XPS configuration after Symmetric queue selection
This fixes some bugs introduced by the "Symmetric queue selection
using XPS for Rx queues".
First, the refactoring of the cleanup function skipped resetting the
queue's NUMA node under some conditions.
Second, the accounting on static keys for XPS and RXQS-XPS is
unbalanced, so the static key for XPS won't actually disable itself,
once enabled. The RXQS-XPS static key can actually be disabled by
reconfiguring a device that didn't have RXQS-XPS configured at all.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Thu, 29 Nov 2018 13:14:49 +0000 (14:14 +0100)]
net: fix XPS static_key accounting
Commit 04157469b7b8 ("net: Use static_key for XPS maps") introduced a
static key for XPS, but the increments/decrements don't match.
First, the static key's counter is incremented once for each queue, but
only decremented once for a whole batch of queues, leading to large
unbalances.
Second, the xps_rxqs_needed key is decremented whenever we reset a batch
of queues, whether they had any rxqs mapping or not, so that if we setup
cpu-XPS on em1 and RXQS-XPS on em2, resetting the queues on em1 would
decrement the xps_rxqs_needed key.
This reworks the accounting scheme so that the xps_needed key is
incremented only once for each type of XPS for all the queues on a
device, and the xps_rxqs_needed key is incremented only once for all
queues. This is sufficient to let us retrieve queues via
get_xps_queue().
This patch introduces a new reset_xps_maps(), which reinitializes and
frees the appropriate map (xps_rxqs_map or xps_cpus_map), and drops a
reference to the needed keys:
- both xps_needed and xps_rxqs_needed, in case of rxqs maps,
- only xps_needed, in case of CPU maps.
Now, we also need to call reset_xps_maps() at the end of
__netif_set_xps_queue() when there's no active map left, for example
when writing '00000000,00000000' to all queues' xps_rxqs setting.
Fixes: 04157469b7b8 ("net: Use static_key for XPS maps") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Thu, 29 Nov 2018 13:14:48 +0000 (14:14 +0100)]
net: restore call to netdev_queue_numa_node_write when resetting XPS
Before commit 80d19669ecd3 ("net: Refactor XPS for CPUs and Rx queues"),
netif_reset_xps_queues() did netdev_queue_numa_node_write() for all the
queues being reset. Now, this is only done when the "active" variable in
clean_xps_maps() is false, ie when on all the CPUs, there's no active
XPS mapping left.
Fixes: 80d19669ecd3 ("net: Refactor XPS for CPUs and Rx queues") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Baruch Siach [Thu, 29 Nov 2018 10:40:11 +0000 (12:40 +0200)]
net: phy: sfp: correct store of detected link modes
The link modes that sfp_parse_support() detects are stored in the
'modes' bitmap. There is no reason to make an exception for 1000Base-PX
or 1000Base-BX10.
Fixes: 03145864bd0f ("sfp: support 1G BiDi (eg, FiberStore SFP-GE-BX) modules") Signed-off-by: Baruch Siach <baruch@tkos.co.il> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 29 Nov 2018 18:38:39 +0000 (10:38 -0800)]
Merge branch 'ave-fixes'
Kunihiko Hayashi says:
====================
fixup AVE ethernet driver
This series adds fixup for AVE ethernet driver that includes increse of
descriptors, replacing macro for linux-next, and adding missing author
information.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kunihiko Hayashi [Thu, 29 Nov 2018 08:08:37 +0000 (17:08 +0900)]
net: ethernet: ave: Replace NET_IP_ALIGN with AVE_FRAME_HEADROOM
In commit 26a4676faa1a ("arm64: mm: define NET_IP_ALIGN to 0"),
AVE controller affects this modification because the controller forces
to ignore lower 2bits of buffer start address, and make 2-byte headroom,
that is, data reception starts from (buffer + 2).
This patch defines AVE_FRAME_HEADROOM macro as hardware-specific value,
and replaces NET_IP_ALIGN with it.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 28 Nov 2018 20:51:10 +0000 (12:51 -0800)]
Merge tag 'xtensa-20181128' of git://github.com/jcmvbkbc/linux-xtensa
Pull Xtensa fixes from Max Filippov:
- fix kernel exception on userspace access to a currently disabled
coprocessor
- fix coprocessor data saving/restoring in configurations with multiple
coprocessors
- fix ptrace access to coprocessor data on configurations with multiple
coprocessors with high alignment requirements
* tag 'xtensa-20181128' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: fix coprocessor part of ptrace_{get,set}xregs
xtensa: fix coprocessor context offset definitions
xtensa: enable coprocessors that are being flushed
David S. Miller [Wed, 28 Nov 2018 19:33:35 +0000 (11:33 -0800)]
Merge branch '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2018-11-28
This series contains fixes to igb, ixgbe and i40e.
Yunjian Wang from Huawei resolves a variable that could potentially be
NULL before it is used.
Lihong fixes an i40e issue which goes back to 4.17 kernels, where
deleting any of the MAC filters was causing the incorrect syncing for
the PF.
Josh Elsasser caught that there were missing enum values in the link
capabilities for x550 devices, which was preventing link for 1000BaseLX
SFP modules.
Jan fixes the function header comments for XSK methods.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 28 Nov 2018 15:20:50 +0000 (16:20 +0100)]
s390/qeth: fix length check in SNMP processing
The response for a SNMP request can consist of multiple parts, which
the cmd callback stages into a kernel buffer until all parts have been
received. If the callback detects that the staging buffer provides
insufficient space, it bails out with error.
This processing is buggy for the first part of the response - while it
initially checks for a length of 'data_len', it later copies an
additional amount of 'offsetof(struct qeth_snmp_cmd, data)' bytes.
Fix the calculation of 'data_len' for the first part of the response.
This also nicely cleans up the memcpy code.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pan Bian [Wed, 28 Nov 2018 07:30:24 +0000 (15:30 +0800)]
net: hisilicon: remove unexpected free_netdev
The net device ndev is freed via free_netdev when failing to register
the device. The control flow then jumps to the error handling code
block. ndev is used and freed again. Resulting in a use-after-free bug.
Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pan Bian [Wed, 28 Nov 2018 06:53:19 +0000 (14:53 +0800)]
rapidio/rionet: do not free skb before reading its length
skb is freed via dev_kfree_skb_any, however, skb->len is read then. This
may result in a use-after-free bug.
Fixes: e6161d64263 ("rapidio/rionet: rework driver initialization and removal") Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Sokolowski [Tue, 27 Nov 2018 17:35:35 +0000 (09:35 -0800)]
i40e: fix kerneldoc for xsk methods
One method, xsk_umem_setup, had an incorrect kernel doc
description, which has been corrected.
Also fixes small typos found in the comments.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Linus Torvalds [Wed, 28 Nov 2018 16:38:20 +0000 (08:38 -0800)]
Merge tag 'for-4.20-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Some of these bugs are being hit during testing so we'd like to get
them merged, otherwise there are usual stability fixes for stable
trees"
* tag 'for-4.20-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: relocation: set trans to be NULL after ending transaction
Btrfs: fix race between enabling quotas and subvolume creation
Btrfs: send, fix infinite loop due to directory rename dependencies
Btrfs: ensure path name is null terminated at btrfs_control_ioctl
Btrfs: fix rare chances for data loss when doing a fast fsync
btrfs: Always try all copies when reading extent buffers
Linus Torvalds [Wed, 28 Nov 2018 16:33:55 +0000 (08:33 -0800)]
Merge tag 'spi-fix-v4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes here, nothing big or that stands out for
anyone other than the driver users.
The omap2-mcspi fix is for issues that started showing up with a
change in defconfig in this release to make cpuidle get turned on by
default"
* tag 'spi-fix-v4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: omap2-mcspi: Add missing suspend and resume calls
spi: mediatek: use correct mata->xfer_len when in fifo transfer
spi: uniphier: fix incorrect property items
Josh Elsasser [Sat, 24 Nov 2018 20:57:33 +0000 (12:57 -0800)]
ixgbe: recognize 1000BaseLX SFP modules as 1Gbps
Add the two 1000BaseLX enum values to the X550's check for 1Gbps modules,
allowing the core driver code to establish a link over this SFP type.
This is done by the out-of-tree driver but the fix wasn't in mainline.
Fixes: e23f33367882 ("ixgbe: Fix 1G and 10G link stability for X550EM_x SFP+”) Fixes: 6a14ee0cfb19 ("ixgbe: Add X550 support function pointers") Signed-off-by: Josh Elsasser <jelsasser@appneta.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Linus Torvalds [Wed, 28 Nov 2018 16:29:18 +0000 (08:29 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Bugfixes, many of them reported by syzkaller and mostly predating the
merge window"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: svm: Ensure an IBPB on all affected CPUs when freeing a vmcb
kvm: mmu: Fix race in emulated page table writes
KVM: nVMX: vmcs12 revision_id is always VMCS12_REVISION even when copied from eVMCS
KVM: nVMX: Verify eVMCS revision id match supported eVMCS version on eVMCS VMPTRLD
KVM: nVMX/nSVM: Fix bug which sets vcpu->arch.tsc_offset to L1 tsc_offset
x86/kvm/vmx: fix old-style function declaration
KVM: x86: fix empty-body warnings
KVM: VMX: Update shared MSRs to be saved/restored on MSR_EFER.LMA changes
KVM: x86: Fix kernel info-leak in KVM_HC_CLOCK_PAIRING hypercall
KVM: nVMX: Fix kernel info-leak when enabling KVM_CAP_HYPERV_ENLIGHTENED_VMCS more than once
svm: Add mutex_lock to protect apic_access_page_done on AMD systems
KVM: X86: Fix scan ioapic use-before-initialization
KVM: LAPIC: Fix pv ipis use-before-initialization
KVM: VMX: re-add ple_gap module parameter
KVM: PPC: Book3S HV: Fix handling for interrupted H_ENTER_NESTED
Lihong Yang [Wed, 21 Nov 2018 17:15:37 +0000 (09:15 -0800)]
i40e: Fix deletion of MAC filters
In __i40e_del_filter function, the flag __I40E_MACVLAN_SYNC_PENDING for
the PF state is wrongly set for the VSI. Deleting any of the MAC filters
has caused the incorrect syncing for the PF. Fix it by setting this state
flag to the intended PF.
CC: stable <stable@vger.kernel.org> Signed-off-by: Lihong Yang <lihong.yang@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Yunjian Wang [Tue, 6 Nov 2018 08:27:12 +0000 (16:27 +0800)]
igb: fix uninitialized variables
This patch fixes the variable 'phy_word' may be used uninitialized.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Taehee Yoo [Wed, 28 Nov 2018 02:27:28 +0000 (11:27 +0900)]
netfilter: nf_tables: deactivate expressions in rule replecement routine
There is no expression deactivation call from the rule replacement path,
hence, chain counter is not decremented. A few steps to reproduce the
problem:
%nft add table ip filter
%nft add chain ip filter c1
%nft add chain ip filter c1
%nft add rule ip filter c1 jump c2
%nft replace rule ip filter c1 handle 3 accept
%nft flush ruleset
<jump c2> expression means immediate NFT_JUMP to chain c2.
Reference count of chain c2 is increased when the rule is added.
When rule is deleted or replaced, the reference counter of c2 should be
decreased via nft_rule_expr_deactivate() which calls
nft_immediate_deactivate().
Bryan Whitehead [Mon, 26 Nov 2018 17:27:10 +0000 (12:27 -0500)]
lan743x: Enable driver to work with LAN7431
This driver was designed to work with both LAN7430 and LAN7431.
The only difference between the two is the LAN7431 has support
for external phy.
This change adds LAN7431 to the list of recognized devices
supported by this driver.
Updates for v2:
changed 'fixes' tag to match defined format
fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver") Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The reason is that the node timer handler sometimes needs to delete a
node which has been disconnected for too long. To do this, it grabs
the lock 'node_list_lock', which may at the same time be held by the
generic node cleanup function, tipc_node_stop(), during module removal.
Since the latter is calling del_timer_sync() inside the same lock, we
have a potential deadlock.
We fix this letting the timer cleanup function use spin_trylock()
instead of just spin_lock(), and when it fails to grab the lock it
just returns so that the timer handler can terminate its execution.
This is safe to do, since tipc_node_stop() anyway is about to
delete both the timer and the node instance.
Fixes: 6a939f365bdb ("tipc: Auto removal of peer down node instance") Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bryan Whitehead [Mon, 26 Nov 2018 17:04:57 +0000 (12:04 -0500)]
lan743x: fix return value for lan743x_tx_napi_poll
The lan743x driver, when under heavy traffic load, has been noticed
to sometimes hang, or cause a kernel panic.
Debugging reveals that the TX napi poll routine was returning
the wrong value, 'weight'. Most other drivers return 0.
And call napi_complete, instead of napi_complete_done.
Additionally when creating the tx napi poll routine.
Changed netif_napi_add, to netif_tx_napi_add.
Updates for v3:
changed 'fixes' tag to match defined format
Updates for v2:
use napi_complete, instead of napi_complete_done in
lan743x_tx_napi_poll
use netif_tx_napi_add, instead of netif_napi_add for
registration of tx napi poll routine
fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver") Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Bianconi [Mon, 26 Nov 2018 14:07:16 +0000 (15:07 +0100)]
net: thunderx: fix NULL pointer dereference in nic_remove
Fix a possible NULL pointer dereference in nic_remove routine
removing the nicpf module if nic_probe fails.
The issue can be triggered with the following reproducer:
Fixes: 4863dea3fab0 ("net: Adding support for Cavium ThunderX network controller") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 26 Nov 2018 06:52:44 +0000 (14:52 +0800)]
sctp: increase sk_wmem_alloc when head->truesize is increased
I changed to count sk_wmem_alloc by skb truesize instead of 1 to
fix the sk_wmem_alloc leak caused by later truesize's change in
xfrm in Commit 02968ccf0125 ("sctp: count sk_wmem_alloc by skb
truesize in sctp_packet_transmit").
But I should have also increased sk_wmem_alloc when head->truesize
is increased in sctp_packet_gso_append() as xfrm does. Otherwise,
sctp gso packet will cause sk_wmem_alloc underflow.
Fixes: 02968ccf0125 ("sctp: count sk_wmem_alloc by skb truesize in sctp_packet_transmit") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Fri, 23 Nov 2018 18:41:29 +0000 (19:41 +0100)]
net: phy: add workaround for issue where PHY driver doesn't bind to the device
After switching the r8169 driver to use phylib some user reported that
their network is broken. This was caused by the genphy PHY driver being
used instead of the dedicated PHY driver for the RTL8211B. Users
reported that loading the Realtek PHY driver module upfront fixes the
issue. See also this mail thread:
https://marc.info/?t=154279781800003&r=1&w=2
The issue is quite weird and the root cause seems to be somewhere in
the base driver core. The patch works around the issue and may be
removed once the actual issue is fixed.
The Fixes tag refers to the first reported occurrence of the issue.
The issue itself may have been existing much longer and it may affect
users of other network chips as well. Users typically will recognize
this issue only if their PHY stops working when being used with the
genphy driver.
Fixes: f1e911d5d0df ("r8169: add basic phylib support") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Bernd Eckstein [Fri, 23 Nov 2018 12:51:26 +0000 (13:51 +0100)]
usbnet: ipheth: fix potential recvmsg bug and recvmsg bug 2
The bug is not easily reproducable, as it may occur very infrequently
(we had machines with 20minutes heavy downloading before it occurred)
However, on a virual machine (VMWare on Windows 10 host) it occurred
pretty frequently (1-2 seconds after a speedtest was started)
dev->tx_skb mab be freed via dev_kfree_skb_irq on a callback
before it is set.
This causes the following problems:
- double free of the skb or potential memory leak
- in dmesg: 'recvmsg bug' and 'recvmsg bug 2' and eventually
general protection fault
The proposed patch eliminates a potential racing condition.
Before, usb_submit_urb was called and _after_ that, the skb was attached
(dev->tx_skb). So, on a callback it was possible, however unlikely that the
skb was freed before it was set. That way (because dev->tx_skb was not set
to NULL after it was freed), it could happen that a skb from a earlier
transmission was freed a second time (and the skb we should have freed did
not get freed at all)
Now we free the skb directly in ipheth_tx(). It is not passed to the
callback anymore, eliminating the posibility of a double free of the same
skb. Depending on the retval of usb_submit_urb() we use dev_kfree_skb_any()
respectively dev_consume_skb_any() to free the skb.
Signed-off-by: Oliver Zweigle <Oliver.Zweigle@faro.com> Signed-off-by: Bernd Eckstein <3ernd.Eckstein@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix several bugs in BPF sparc JIT, that is, convergence for fused
branches, initialization of frame pointer register, and moving all
arguments into output registers from input registers in prologue
to fix BPF to BPF calls, from David.
2) Fix a bug in arm64 JIT for fetching BPF to BPF call addresses where
they are not guaranteed to fit into imm field and therefore must be
retrieved through prog aux data, from Daniel.
3) Explicitly add all JITs to MAINTAINERS file with developers able to
help out in feature development, fixes, review, etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jim Mattson [Tue, 22 May 2018 16:54:20 +0000 (09:54 -0700)]
kvm: svm: Ensure an IBPB on all affected CPUs when freeing a vmcb
Previously, we only called indirect_branch_prediction_barrier on the
logical CPU that freed a vmcb. This function should be called on all
logical CPUs that last loaded the vmcb in question.
Fixes: 15d45071523d ("KVM/x86: Add IBPB support") Reported-by: Neel Natu <neelnatu@google.com> Signed-off-by: Jim Mattson <jmattson@google.com> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Junaid Shahid [Wed, 31 Oct 2018 21:53:57 +0000 (14:53 -0700)]
kvm: mmu: Fix race in emulated page table writes
When a guest page table is updated via an emulated write,
kvm_mmu_pte_write() is called to update the shadow PTE using the just
written guest PTE value. But if two emulated guest PTE writes happened
concurrently, it is possible that the guest PTE and the shadow PTE end
up being out of sync. Emulated writes do not mark the shadow page as
unsync-ed, so this inconsistency will not be resolved even by a guest TLB
flush (unless the page was marked as unsync-ed at some other point).
This is fixed by re-reading the current value of the guest PTE after the
MMU lock has been acquired instead of just using the value that was
written prior to calling kvm_mmu_pte_write().
Signed-off-by: Junaid Shahid <junaids@google.com> Reviewed-by: Wanpeng Li <wanpengli@tencent.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Liran Alon [Tue, 13 Nov 2018 15:44:46 +0000 (17:44 +0200)]
KVM: nVMX: vmcs12 revision_id is always VMCS12_REVISION even when copied from eVMCS
vmcs12 represents the per-CPU cache of L1 active vmcs12.
This cache can be loaded by one of the following:
1) Guest making a vmcs12 active by exeucting VMPTRLD
2) Guest specifying eVMCS in VP assist page and executing
VMLAUNCH/VMRESUME.
Either way, vmcs12 should have revision_id of VMCS12_REVISION.
Which is not equal to eVMCS revision_id which specifies used
VersionNumber of eVMCS struct (e.g. KVM_EVMCS_VERSION).
Specifically, this causes an issue in restoring a nested VM state
because vmx_set_nested_state() verifies that vmcs12->revision_id
is equal to VMCS12_REVISION which was not true in case vmcs12
was populated from an eVMCS by vmx_get_nested_state() which calls
copy_enlightened_to_vmcs12().
Reviewed-by: Darren Kenny <darren.kenny@oracle.com> Signed-off-by: Liran Alon <liran.alon@oracle.com> Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Liran Alon [Thu, 1 Nov 2018 08:57:39 +0000 (10:57 +0200)]
KVM: nVMX: Verify eVMCS revision id match supported eVMCS version on eVMCS VMPTRLD
According to TLFS section 16.11.2 Enlightened VMCS, the first u32
field of eVMCS should specify eVMCS VersionNumber.
This version should be in the range of supported eVMCS versions exposed
to guest via CPUID.0x4000000A.EAX[0:15].
The range which KVM expose to guest in this CPUID field should be the
same as the value returned in vmcs_version by nested_enable_evmcs().
According to the above, eVMCS VMPTRLD should verify that version specified
in given eVMCS is in the supported range. However, current code
mistakenly verfies this field against VMCS12_REVISION.
One can also see that when KVM use eVMCS, it makes sure that
alloc_vmcs_cpu() sets allocated eVMCS revision_id to KVM_EVMCS_VERSION.
Obvious fix should just change eVMCS VMPTRLD to verify first u32 field
of eVMCS is equal to KVM_EVMCS_VERSION.
However, it turns out that Microsoft Hyper-V fails to comply to their
own invented interface: When Hyper-V use eVMCS, it just sets first u32
field of eVMCS to revision_id specified in MSR_IA32_VMX_BASIC (In our
case: VMCS12_REVISION). Instead of used eVMCS version number which is
one of the supported versions specified in CPUID.0x4000000A.EAX[0:15].
To overcome Hyper-V bug, we accept either a supported eVMCS version
or VMCS12_REVISION as valid values for first u32 field of eVMCS.
Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com> Reviewed-by: Mark Kanda <mark.kanda@oracle.com> Signed-off-by: Liran Alon <liran.alon@oracle.com> Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Leonid Shatz [Tue, 6 Nov 2018 10:14:25 +0000 (12:14 +0200)]
KVM: nVMX/nSVM: Fix bug which sets vcpu->arch.tsc_offset to L1 tsc_offset
Since commit e79f245ddec1 ("X86/KVM: Properly update 'tsc_offset' to
represent the running guest"), vcpu->arch.tsc_offset meaning was
changed to always reflect the tsc_offset value set on active VMCS.
Regardless if vCPU is currently running L1 or L2.
However, above mentioned commit failed to also change
kvm_vcpu_write_tsc_offset() to set vcpu->arch.tsc_offset correctly.
This is because vmx_write_tsc_offset() could set the tsc_offset value
in active VMCS to given offset parameter *plus vmcs12->tsc_offset*.
However, kvm_vcpu_write_tsc_offset() just sets vcpu->arch.tsc_offset
to given offset parameter. Without taking into account the possible
addition of vmcs12->tsc_offset. (Same is true for SVM case).
Fix this issue by changing kvm_x86_ops->write_tsc_offset() to return
actually set tsc_offset in active VMCS and modify
kvm_vcpu_write_tsc_offset() to set returned value in
vcpu->arch.tsc_offset.
In addition, rename write_tsc_offset() callback to write_l1_tsc_offset()
to make it clear that it is meant to set L1 TSC offset.
Fixes: e79f245ddec1 ("X86/KVM: Properly update 'tsc_offset' to represent the running guest") Reviewed-by: Liran Alon <liran.alon@oracle.com> Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com> Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com> Signed-off-by: Leonid Shatz <leonid.shatz@oracle.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Yi Wang [Thu, 8 Nov 2018 03:22:21 +0000 (11:22 +0800)]
x86/kvm/vmx: fix old-style function declaration
The inline keyword which is not at the beginning of the function
declaration may trigger the following build warnings, so let's fix it:
arch/x86/kvm/vmx.c:1309:1: warning: ‘inline’ is not at beginning of declaration [-Wold-style-declaration]
arch/x86/kvm/vmx.c:5947:1: warning: ‘inline’ is not at beginning of declaration [-Wold-style-declaration]
arch/x86/kvm/vmx.c:5985:1: warning: ‘inline’ is not at beginning of declaration [-Wold-style-declaration]
arch/x86/kvm/vmx.c:6023:1: warning: ‘inline’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Yi Wang [Thu, 8 Nov 2018 08:48:36 +0000 (16:48 +0800)]
KVM: x86: fix empty-body warnings
We get the following warnings about empty statements when building
with 'W=1':
arch/x86/kvm/lapic.c:632:53: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
arch/x86/kvm/lapic.c:1907:42: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
arch/x86/kvm/lapic.c:1936:65: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
arch/x86/kvm/lapic.c:1975:44: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
Rework the debug helper macro to get rid of these warnings.
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Liran Alon [Tue, 20 Nov 2018 16:03:25 +0000 (18:03 +0200)]
KVM: VMX: Update shared MSRs to be saved/restored on MSR_EFER.LMA changes
When guest transitions from/to long-mode by modifying MSR_EFER.LMA,
the list of shared MSRs to be saved/restored on guest<->host
transitions is updated (See vmx_set_efer() call to setup_msrs()).
On every entry to guest, vcpu_enter_guest() calls
vmx_prepare_switch_to_guest(). This function should also take care
of setting the shared MSRs to be saved/restored. However, the
function does nothing in case we are already running with loaded
guest state (vmx->loaded_cpu_state != NULL).
This means that even when guest modifies MSR_EFER.LMA which results
in updating the list of shared MSRs, it isn't being taken into account
by vmx_prepare_switch_to_guest() because it happens while we are
running with loaded guest state.
To fix above mentioned issue, add a flag to mark that the list of
shared MSRs has been updated and modify vmx_prepare_switch_to_guest()
to set shared MSRs when running with host state *OR* list of shared
MSRs has been updated.
Note that this issue was mistakenly introduced by commit 678e315e78a7 ("KVM: vmx: add dedicated utility to access guest's
kernel_gs_base") because previously vmx_set_efer() always called
vmx_load_host_state() which resulted in vmx_prepare_switch_to_guest() to
set shared MSRs.
Fixes: 678e315e78a7 ("KVM: vmx: add dedicated utility to access guest's kernel_gs_base") Reported-by: Eyal Moscovici <eyal.moscovici@oracle.com> Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com> Reviewed-by: Liam Merwick <liam.merwick@oracle.com> Reviewed-by: Jim Mattson <jmattson@google.com> Signed-off-by: Liran Alon <liran.alon@oracle.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Liran Alon [Wed, 7 Nov 2018 22:43:06 +0000 (00:43 +0200)]
KVM: x86: Fix kernel info-leak in KVM_HC_CLOCK_PAIRING hypercall
kvm_pv_clock_pairing() allocates local var
"struct kvm_clock_pairing clock_pairing" on stack and initializes
all it's fields besides padding (clock_pairing.pad[]).
Because clock_pairing var is written completely (including padding)
to guest memory, failure to init struct padding results in kernel
info-leak.
Fix the issue by making sure to also init the padding with zeroes.
Fixes: 55dd00a73a51 ("KVM: x86: add KVM_HC_CLOCK_PAIRING hypercall") Reported-by: syzbot+a8ef68d71211ba264f56@syzkaller.appspotmail.com Reviewed-by: Mark Kanda <mark.kanda@oracle.com> Signed-off-by: Liran Alon <liran.alon@oracle.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Liran Alon [Sat, 17 Nov 2018 12:05:06 +0000 (14:05 +0200)]
KVM: nVMX: Fix kernel info-leak when enabling KVM_CAP_HYPERV_ENLIGHTENED_VMCS more than once
Consider the case that userspace enables KVM_CAP_HYPERV_ENLIGHTENED_VMCS twice:
1) kvm_vcpu_ioctl_enable_cap() is called to enable
KVM_CAP_HYPERV_ENLIGHTENED_VMCS which calls nested_enable_evmcs().
2) nested_enable_evmcs() sets enlightened_vmcs_enabled to true and fills
vmcs_version which is then copied to userspace.
3) kvm_vcpu_ioctl_enable_cap() is called again to enable
KVM_CAP_HYPERV_ENLIGHTENED_VMCS which calls nested_enable_evmcs().
4) This time nested_enable_evmcs() just returns 0 as
enlightened_vmcs_enabled is already true. *Without filling
vmcs_version*.
5) kvm_vcpu_ioctl_enable_cap() continues as usual and copies
*uninitialized* vmcs_version to userspace which leads to kernel info-leak.
Fix this issue by simply changing nested_enable_evmcs() to always fill
vmcs_version output argument. Even when enlightened_vmcs_enabled is
already set to true.
Note that SVM's nested_enable_evmcs() should not be modified because it
always returns a non-zero value (-ENODEV) which results in
kvm_vcpu_ioctl_enable_cap() skipping the copy of vmcs_version to
userspace (as it should).
Wei Wang [Mon, 12 Nov 2018 12:23:14 +0000 (12:23 +0000)]
svm: Add mutex_lock to protect apic_access_page_done on AMD systems
There is a race condition when accessing kvm->arch.apic_access_page_done.
Due to it, x86_set_memory_region will fail when creating the second vcpu
for a svm guest.
Add a mutex_lock to serialize the accesses to apic_access_page_done.
This lock is also used by vmx for the same purpose.
The reason is that the testcase writes hyperv synic HV_X64_MSR_SINT6 msr
and triggers scan ioapic logic to load synic vectors into EOI exit bitmap.
However, irqchip is not initialized by this simple testcase, ioapic/apic
objects should not be accessed.
This can be triggered by the following program:
The reason is that the apic map has not yet been initialized, the testcase
triggers pv_send_ipi interface by vmcall which results in kvm->arch.apic_map
is dereferenced. This patch fixes it by checking whether or not apic map is
NULL and bailing out immediately if that is the case.
Max Filippov [Tue, 27 Nov 2018 02:06:01 +0000 (18:06 -0800)]
xtensa: fix coprocessor part of ptrace_{get,set}xregs
Layout of coprocessor registers in the elf_xtregs_t and
xtregs_coprocessor_t may be different due to alignment. Thus it is not
always possible to copy data between the xtregs_coprocessor_t structure
and the elf_xtregs_t and get correct values for all registers.
Use a table of offsets and sizes of individual coprocessor register
groups to do coprocessor context copying in the ptrace_getxregs and
ptrace_setxregs.
This fixes incorrect coprocessor register values reading from the user
process by the native gdb on an xtensa core with multiple coprocessors
and registers with high alignment requirements.
Cc: stable@vger.kernel.org Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Coprocessor context offsets are used by the assembly code that moves
coprocessor context between the individual fields of the
thread_info::xtregs_cp structure and coprocessor registers.
This fixes coprocessor context clobbering on flushing and reloading
during normal user code execution and user process debugging in the
presence of more than one coprocessor in the core configuration.
Cc: stable@vger.kernel.org Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Max Filippov [Mon, 26 Nov 2018 21:29:41 +0000 (13:29 -0800)]
xtensa: enable coprocessors that are being flushed
coprocessor_flush_all may be called from a context of a thread that is
different from the thread being flushed. In that case contents of the
cpenable special register may not match ti->cpenable of the target
thread, resulting in unhandled coprocessor exception in the kernel
context.
Set cpenable special register to the ti->cpenable of the target register
for the duration of the flush and restore it afterwards.
This fixes the following crash caused by coprocessor register inspection
in native gdb:
Matias Bjørling [Mon, 26 Nov 2018 19:27:03 +0000 (11:27 -0800)]
ia64: export node_distance function
The numa_slit variable used by node_distance is available to a
module as long as it is linked at compile-time. However, it is
not available to loadable modules. Leading to errors such as:
The error above is caused by the nvme multipath code that makes
use of node_distance for its path calculation. When the patch was
added, the lightnvm subsystem would select nvme and always compile
it in, leading to the node_distance call to always succeed.
However, when this requirement was removed, nvme could be compiled
in as a module, which exposed this bug.
This patch extracts node_distance to a function and exports it.
Since ACPI is depending on node_distance being a simple lookup to
numa_slit, the previous behavior is exposed as slit_distance and its
users updated.
Fixes: f333444708f82 "nvme: take node locality into account when selecting a path" Fixes: 73569e11032f "lightnvm: remove dependencies on BLK_DEV_NVME and PCI" Signed-off-by: Matias Bjøring <mb@lightnvm.io> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Borkmann [Tue, 27 Nov 2018 00:21:00 +0000 (01:21 +0100)]
bpf, doc: add entries of who looks over which jits
Make the high-level BPF JIT entry a general 'catch-all' and add
architecture specific entries to make it more clear who actively
maintains which BPF JIT compiler. The list (L) address implies
that this eventually lands in the bpf patchwork bucket. Goal is
that this set of responsible developers listed here is always up
to date and a point of contact for helping out in e.g. feature
development, fixes, review or testing patches in order to help
long-term in ensuring quality of the BPF JITs and therefore BPF
core under a given architecture. Every new JIT in future /must/
have an entry here as well.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Acked-by: Sandipan Das <sandipan@linux.ibm.com> Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> Acked-by: David S. Miller <davem@davemloft.net> Acked-by: Zi Shen Lim <zlim.lnx@gmail.com> Acked-by: Paul Burton <paul.burton@mips.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Wang YanQing <udknight@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
David Miller [Mon, 26 Nov 2018 22:52:18 +0000 (14:52 -0800)]
sparc: Correct ctx->saw_frame_pointer logic.
We need to initialize the frame pointer register not just if it is
seen as a source operand, but also if it is seen as the destination
operand of a store or an atomic instruction (which effectively is a
source operand).
This is exercised by test_verifier's "non-invalid fp arithmetic"
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
David Miller [Mon, 26 Nov 2018 21:03:46 +0000 (13:03 -0800)]
sparc: Fix JIT fused branch convergance.
On T4 and later sparc64 cpus we can use the fused compare and branch
instruction.
However, it can only be used if the branch destination is in the range
of a signed 10-bit immediate offset. This amounts to 1024
instructions forwards or backwards.
After the commit referenced in the Fixes: tag, the largest possible
size program seen by the JIT explodes by a significant factor.
As a result of this convergance takes many more passes since the
expanded "BPF_LDX | BPF_MSH | BPF_B" code sequence, for example,
contains several embedded branch on condition instructions.
On each pass, as suddenly new fused compare and branch instances
become valid, this makes thousands more in range for the next pass.
And so on and so forth.
This is most greatly exemplified by "BPF_MAXINSNS: exec all MSH" which
takes 35 passes to converge, and shrinks the image by about 64K.
To decrease the cost of this number of convergance passes, do the
convergance pass before we have the program image allocated, just like
other JITs (such as x86) do.
Fixes: e0cea7ce988c ("bpf: implement ld_abs/ld_ind in native bpf") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
====================
This set contains a fix for arm64 BPF JIT. First patch generalizes
ppc64 way of retrieving subprog into bpf_jit_get_func_addr() as core
code and uses the same on arm64 in second patch. Tested on both arm64
and ppc64.
====================
Daniel Borkmann [Mon, 26 Nov 2018 13:05:39 +0000 (14:05 +0100)]
bpf, arm64: fix getting subprog addr from aux for calls
The arm64 JIT has the same issue as ppc64 JIT in that the relative BPF
to BPF call offset can be too far away from core kernel in that relative
encoding into imm is not sufficient and could potentially be truncated,
see also fd045f6cd98e ("arm64: add support for module PLTs") which adds
spill-over space for module_alloc() and therefore bpf_jit_binary_alloc().
Therefore, use the recently added bpf_jit_get_func_addr() helper for
properly fetching the address through prog->aux->func[off]->bpf_func
instead. This also has the benefit to optimize normal helper calls since
their address can use the optimized emission. Tested on Cavium ThunderX
CN8890.
Fixes: db496944fdaa ("bpf: arm64: add JIT support for multi-function programs") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann [Mon, 26 Nov 2018 13:05:38 +0000 (14:05 +0100)]
bpf, ppc64: generalize fetching subprog into bpf_jit_get_func_addr
Make fetching of the BPF call address from ppc64 JIT generic. ppc64
was using a slightly different variant rather than through the insns'
imm field encoding as the target address would not fit into that space.
Therefore, the target subprog number was encoded into the insns' offset
and fetched through fp->aux->func[off]->bpf_func instead. Given there
are other JITs with this issue and the mechanism of fetching the address
is JIT-generic, move it into the core as a helper instead. On the JIT
side, we get information on whether the retrieved address is a fixed
one, that is, not changing through JIT passes, or a dynamic one. For
the former, JITs can optimize their imm emission because this doesn't
change jump offsets throughout JIT process.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Sandipan Das <sandipan@linux.ibm.com> Tested-by: Sandipan Das <sandipan@linux.ibm.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
All lists that reach the tree_nodes_free() function have both zero
counter and true dead flag. The reason for this is that lists to be
release are selected by nf_conncount_gc_list() which already decrements
the list counter and sets on the dead flag. Therefore, this if statement
in tree_nodes_free() is unnecessary and wrong.
Fixes: 31568ec09ea0 ("netfilter: nf_conncount: fix list_del corruption in conn_free") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Taehee Yoo [Thu, 22 Nov 2018 10:59:57 +0000 (19:59 +0900)]
netfilter: nat: fix double register in masquerade modules
There is a reference counter to ensure that masquerade modules register
notifiers only once. However, the existing reference counter approach is
not safe, test commands are:
while :
do
modprobe ip6t_MASQUERADE &
modprobe nft_masq_ipv6 &
modprobe -rv ip6t_MASQUERADE &
modprobe -rv nft_masq_ipv6 &
done
Alin Nastac [Wed, 21 Nov 2018 13:00:30 +0000 (14:00 +0100)]
netfilter: ipv6: Preserve link scope traffic original oif
When ip6_route_me_harder is invoked, it resets outgoing interface of:
- link-local scoped packets sent by neighbor discovery
- multicast packets sent by MLD host
- multicast packets send by MLD proxy daemon that sets outgoing
interface through IPV6_PKTINFO ipi6_ifindex
Link-local and multicast packets must keep their original oif after
ip6_route_me_harder is called.
Signed-off-by: Alin Nastac <alin.nastac@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Linus Torvalds [Mon, 26 Nov 2018 17:34:31 +0000 (09:34 -0800)]
Merge tag 'hwmon-for-v4.20-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- fix temp4_type attribute permissions in w83795 driver
- fix tacho fault detection in mlxreg-fan driver
- fix current value calculations in ina2xx driver
- fix initial notification/warning in raspberrypi driver
- fix a NULL pointer access in ina2xx
* tag 'hwmon-for-v4.20-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (w83795) temp4_type has writable permission
hwmon: (mlxreg-fan) Fix macros for tacho fault reading
hwmon: (ina2xx) Fix current value calculation
hwmon: (raspberrypi) Fix initial notify
hwmon (ina2xx) Fix NULL id pointer in probe()
Florian Westphal [Sat, 17 Nov 2018 10:32:29 +0000 (11:32 +0100)]
netfilter: nfnetlink_cttimeout: fetch timeouts for udplite and gre, too
syzbot was able to trigger the WARN in cttimeout_default_get() by
passing UDPLITE as l4protocol. Alias UDPLITE to UDP, both use
same timeout values.
Furthermore, also fetch GRE timeouts. GRE is a bit more complicated,
as it still can be a module and its netns_proto_gre struct layout isn't
visible outside of the gre module. Can't move timeouts around, it
appears conntrack sysctl unregister assumes net_generic() returns
nf_proto_net, so we get crash. Expose layout of netns_proto_gre instead.
A followup nf-next patch could make gre tracker be built-in as well
if needed, its not that large.
Last, make the WARN() mention the missing protocol value in case
anything else is missing.
Xin Long [Thu, 15 Nov 2018 07:14:30 +0000 (15:14 +0800)]
ipvs: call ip_vs_dst_notifier earlier than ipv6_dev_notf
ip_vs_dst_event is supposed to clean up all dst used in ipvs'
destinations when a net dev is going down. But it works only
when the dst's dev is the same as the dev from the event.
Now with the same priority but late registration,
ip_vs_dst_notifier is always called later than ipv6_dev_notf
where the dst's dev is set to lo for NETDEV_DOWN event.
As the dst's dev lo is not the same as the dev from the event
in ip_vs_dst_event, ip_vs_dst_notifier doesn't actually work.
Also as these dst have to wait for dest_trash_timer to clean
them up. It would cause some non-permanent kernel warnings:
unregister_netdevice: waiting for br0 to become free. Usage count = 3
To fix it, call ip_vs_dst_notifier earlier than ipv6_dev_notf
by increasing its priority to ADDRCONF_NOTIFY_PRIORITY + 5.
Note that for ipv4 route fib_netdev_notifier doesn't set dst's
dev to lo in NETDEV_DOWN event, so this fix is only needed when
IP_VS_IPV6 is defined.
Fixes: 7a4f0761fce3 ("IPVS: init and cleanup restructuring") Reported-by: Li Shuang <shuali@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Julian Anastasov <ja@ssi.bg> Acked-by: Simon Horman <horms@verge.net.au> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix an off-by-one bug when adjusting subprog start offsets after
patching, from Edward.
2) Fix several bugs such as overflow in size allocation in queue /
stack map creation, from Alexei.
3) Fix wrong IPv6 destination port byte order in bpf_sk_lookup_udp
helper, from Andrey.
4) Fix several bugs in bpftool such as preventing an infinite loop
in get_fdinfo, error handling and man page references, from Quentin.
5) Fix a warning in bpf_trace_printk() that wasn't catching an
invalid format string, from Martynas.
6) Fix a bug in BPF cgroup local storage where non-atomic allocation
was used in atomic context, from Roman.
7) Fix a NULL pointer dereference bug in bpftool from reallocarray()
error handling, from Jakub and Wen.
8) Add a copy of pkt_cls.h and tc_bpf.h uapi headers to the tools
include infrastructure so that bpftool compiles on older RHEL7-like
user space which does not ship these headers, from Yonghong.
9) Fix BPF kselftests for user space where to get ping test working
with ping6 and ping -6, from Li.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-kernels.git / log