Linus Torvalds [Sun, 31 Dec 2017 20:27:19 +0000 (12:27 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"Three patches addressing the fallout of the CPU_ISOLATION changes
especially with NO_HZ_FULL plus documentation of boot parameter
dependency"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/isolation: Document boot parameters dependency on CONFIG_CPU_ISOLATION=y
sched/isolation: Enable CONFIG_CPU_ISOLATION=y by default
sched/isolation: Make CONFIG_NO_HZ_FULL select CONFIG_CPU_ISOLATION
Linus Torvalds [Sun, 31 Dec 2017 19:47:24 +0000 (11:47 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
- plug a memory leak in the intel pmu init code
- clang fixes
- tooling fix to avoid including kernel headers
- a fix for jvmti to generate correct debug information for inlined
code
- replace backtick with a regular shell function
- fix the build in hardened environments
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Plug memory leak in intel_pmu_init()
x86/asm: Allow again using asm.h when building for the 'bpf' clang target
tools arch s390: Do not include header files from the kernel sources
perf jvmti: Generate correct debug information for inlined code
perf tools: Fix up build in hardened environments
perf tools: Use shell function for perl cflags retrieval
Linus Torvalds [Sun, 31 Dec 2017 19:23:11 +0000 (11:23 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A rather large update after the kaisered maintainer finally found time
to handle regression reports.
- The larger part addresses a regression caused by the x86 vector
management rework.
The reservation based model does not work reliably for MSI
interrupts, if they cannot be masked (yes, yet another hw
engineering trainwreck). The reason is that the reservation mode
assigns a dummy vector when the interrupt is allocated and switches
to a real vector when the interrupt is requested.
If the MSI entry cannot be masked then the initialization might
raise an interrupt before the interrupt is requested, which ends up
as spurious interrupt and causes device malfunction and worse. The
fix is to exclude MSI interrupts which do not support masking from
reservation mode and assign a real vector right away.
- Extend the extra lockdep class setup for nested interrupts with a
class for the recently added irq_desc::request_mutex so lockdep can
differeniate and does not emit false positive warnings.
- A ratelimit guard for the bad irq printout so in case a bad irq
comes back immediately the system does not drown in dmesg spam"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/msi, x86/vector: Prevent reservation mode for non maskable MSI
genirq/irqdomain: Rename early argument of irq_domain_activate_irq()
x86/vector: Use IRQD_CAN_RESERVE flag
genirq: Introduce IRQD_CAN_RESERVE flag
genirq/msi: Handle reactivation only on success
gpio: brcmstb: Make really use of the new lockdep class
genirq: Guard handle_bad_irq log messages
kernel/irq: Extend lockdep class for request mutex
Linus Torvalds [Sun, 31 Dec 2017 18:57:10 +0000 (10:57 -0800)]
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool fixes from Thomas Gleixner:
"Three fixlets for objtool:
- Address two segfaults related to missing parameter and clang
objects
- Make it compile clean with clang"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix seg fault with clang-compiled objects
objtool: Fix seg fault caused by missing parameter
objtool: Fix Clang enum conversion warning
Linus Torvalds [Sun, 31 Dec 2017 18:52:51 +0000 (10:52 -0800)]
Merge tag 'char-misc-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are six small fixes of some of the char/misc drivers that have
been sent in to resolve reported issues.
Nothing major, a binder use-after-free fix, some thunderbolt bugfixes,
a hyper-v bugfix, and an nvmem driver fix. All of these have been in
linux-next with no reported issues for a while"
* tag 'char-misc-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
nvmem: meson-mx-efuse: fix reading from an offset other than 0
binder: fix proc->files use-after-free
vmbus: unregister device_obj->channels_kset
thunderbolt: Mask ring interrupt properly when polling starts
MAINTAINERS: Add thunderbolt.rst to the Thunderbolt driver entry
thunderbolt: Make pathname to force_power shorter
Linus Torvalds [Sun, 31 Dec 2017 18:50:05 +0000 (10:50 -0800)]
Merge tag 'driver-core-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two driver core fixes for 4.15-rc6, resolving some reported
issues.
The first is a cacheinfo fix for DT based systems to resolve a
reported issue that has been around for a while, and the other is to
resolve a regression in the kobject uevent code that showed up in
4.15-rc1.
Both have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kobject: fix suppressing modalias in uevents delivered over netlink
drivers: base: cacheinfo: fix cache type for non-architected system cache
Linus Torvalds [Sun, 31 Dec 2017 18:44:00 +0000 (10:44 -0800)]
Merge tag 'usb-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY fixes from Greg KH:
"Here are a number of small USB and PHY driver fixes for 4.15-rc6.
Nothing major, but there are a number of regression fixes in here that
resolve issues that have been reported a bunch. There are also the
usual xhci fixes as well as a number of new usb serial device ids.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: xhci: Add XHCI_TRUST_TX_LENGTH for Renesas uPD720201
xhci: Fix use-after-free in xhci debugfs
xhci: Fix xhci debugfs NULL pointer dereference in resume from hibernate
USB: serial: ftdi_sio: add id for Airbus DS P8GR
usb: Add device quirk for Logitech HD Pro Webcam C925e
usb: add RESET_RESUME for ELSA MicroLink 56K
usbip: fix usbip bind writing random string after command in match_busid
usbip: stub_rx: fix static checker warning on unnecessary checks
usbip: prevent leaking socket pointer address in messages
usbip: stub: stop printing kernel pointer addresses in messages
usbip: vhci: stop printing kernel pointer addresses in messages
USB: Fix off by one in type-specific length check of BOS SSP capability
USB: serial: option: adding support for YUGA CLM920-NC5
phy: rcar-gen3-usb2: select USB_COMMON
phy: rockchip-typec: add pm_runtime_disable in err case
phy: cpcap-usb: Fix platform_get_irq_byname's error checking.
phy: tegra: fix device-tree node lookups
USB: serial: qcserial: add Sierra Wireless EM7565
USB: serial: option: add support for Telit ME910 PID 0x1101
USB: chipidea: msm: fix ulpi-node lookup
Adam Borowski [Mon, 25 Dec 2017 15:38:58 +0000 (16:38 +0100)]
MAINTAINERS: mark arch/blackfin/ and its gubbins as orphaned
The blackfin architecture has seen no maintainer action of any kind since
April 2015. No new code, no pull requests, no acks to patches, no response
to mails, nothing.
The web site has an expired certificate (expiration Sep 2017, issued in
2013), the mailing list sees no answers either, with one exception:
https://sourceforge.net/p/adi-buildroot/mailman/adi-buildroot-devel/
>
> Steven is no longer working on this for ADI. Acked by me if this works. Thanks.
>
> Best regards,
> Aaron Wu
> Analog Devices Inc.
But, Aaron doesn't seem to respond to queries either.
Linus Torvalds [Sat, 30 Dec 2017 22:31:30 +0000 (14:31 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two simple fixes, both of which cause I/O hangs.
The storvsc one is from the hyper-v which can hang under certain hot
add/remove conditions and the other is generally, where removing a
target and a device in close proximity can result in the release
method being executed twice (and subsequent list and other corruption
and an eventual panic)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: storvsc: Fix scsi_cmd error assignments in storvsc_handle_error
scsi: core: check for device state in __scsi_remove_target()
Simon Ser [Sat, 30 Dec 2017 20:43:32 +0000 (14:43 -0600)]
objtool: Fix seg fault with clang-compiled objects
Fix a seg fault which happens when an input file provided to 'objtool
orc generate' doesn't have a '.shstrtab' section (for instance, object
files produced by clang don't have this section).
Linus Torvalds [Sat, 30 Dec 2017 18:16:51 +0000 (10:16 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- two cosmetic fixes from Daniel Axtens and Hans de Goede
- fix for I2C command mismatch fix for cp2112 driver from Eudean Sun
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: core: lower log level for unknown main item tags to warnings
HID: holtekff: move MODULE_* parameters out of #ifdef block
HID: cp2112: Fix I2C_BLOCK_DATA transactions
Linus Torvalds [Sat, 30 Dec 2017 01:34:43 +0000 (17:34 -0800)]
kbuild: add '-fno-stack-check' to kernel build options
It appears that hardened gentoo enables "-fstack-check" by default for
gcc.
That doesn't work _at_all_ for the kernel, because the kernel stack
doesn't act like a user stack at all: it's much smaller, and it doesn't
auto-expand on use. So the extra "probe one page below the stack" code
generated by -fstack-check just breaks the kernel in horrible ways,
causing infinite double faults etc.
[ I have to say, that the particular code gcc generates looks very
stupid even for user space where it works, but that's a separate
issue. ]
Reported-and-tested-by: Alexander Tsoy <alexander@tsoy.me> Reported-and-tested-by: Toralf Förster <toralf.foerster@gmx.de> Cc: stable@kernel.org Cc: Dave Hansen <dave.hansen@intel.com> Cc: Jiri Kosina <jikos@kernel.org> Cc: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 30 Dec 2017 01:02:49 +0000 (17:02 -0800)]
Merge branch 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 page table isolation updates from Thomas Gleixner:
"This is the final set of enabling page table isolation on x86:
- Infrastructure patches for handling the extra page tables.
- Patches which map the various bits and pieces which are required to
get in and out of user space into the user space visible page
tables.
- The required changes to have CR3 switching in the entry/exit code.
- Optimizations for the CR3 switching along with documentation how
the ASID/PCID mechanism works.
- Updates to dump pagetables to cover the user space page tables for
W+X scans and extra debugfs files to analyze both the kernel and
the user space visible page tables
The whole functionality is compile time controlled via a config switch
and can be turned on/off on the command line as well"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
x86/ldt: Make the LDT mapping RO
x86/mm/dump_pagetables: Allow dumping current pagetables
x86/mm/dump_pagetables: Check user space page table for WX pages
x86/mm/dump_pagetables: Add page table directory to the debugfs VFS hierarchy
x86/mm/pti: Add Kconfig
x86/dumpstack: Indicate in Oops whether PTI is configured and enabled
x86/mm: Clarify the whole ASID/kernel PCID/user PCID naming
x86/mm: Use INVPCID for __native_flush_tlb_single()
x86/mm: Optimize RESTORE_CR3
x86/mm: Use/Fix PCID to optimize user/kernel switches
x86/mm: Abstract switching CR3
x86/mm: Allow flushing for future ASID switches
x86/pti: Map the vsyscall page if needed
x86/pti: Put the LDT in its own PGD if PTI is on
x86/mm/64: Make a full PGD-entry size hole in the memory map
x86/events/intel/ds: Map debug buffers in cpu_entry_area
x86/cpu_entry_area: Add debugstore entries to cpu_entry_area
x86/mm/pti: Map ESPFIX into user space
x86/mm/pti: Share entry text PMD
x86/entry: Align entry text section to PMD boundary
...
Thomas Gleixner [Fri, 29 Dec 2017 09:47:22 +0000 (10:47 +0100)]
genirq/msi, x86/vector: Prevent reservation mode for non maskable MSI
The new reservation mode for interrupts assigns a dummy vector when the
interrupt is allocated and assigns a real vector when the interrupt is
requested. The reservation mode prevents vector pressure when devices with
a large amount of queues/interrupts are initialized, but only a minimal
subset of those queues/interrupts is actually used.
This mode has an issue with MSI interrupts which cannot be masked. If the
driver is not careful or the hardware emits an interrupt before the device
irq is requestd by the driver then the interrupt ends up on the dummy
vector as a spurious interrupt which can cause malfunction of the device or
in the worst case a lockup of the machine.
Change the logic for the reservation mode so that the early activation of
MSI interrupts checks whether:
- the device is a PCI/MSI device
- the reservation mode of the underlying irqdomain is activated
- PCI/MSI masking is globally enabled
- the PCI/MSI device uses either MSI-X, which supports masking, or
MSI with the maskbit supported.
If one of those conditions is false, then clear the reservation mode flag
in the irq data of the interrupt and invoke irq_domain_activate_irq() with
the reserve argument cleared. In the x86 vector code, clear the can_reserve
flag in the vector allocation data so a subsequent free_irq() won't create
the same situation again. The interrupt stays assigned to a real vector
until pci_disable_msi() is invoked and all allocations are undone.
Fixes: 4900be83602b ("x86/vector/msi: Switch to global reservation mode") Reported-by: Alexandru Chirvasitu <achirvasub@gmail.com> Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Alexandru Chirvasitu <achirvasub@gmail.com> Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Dou Liyang <douly.fnst@cn.fujitsu.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Maciej W. Rozycki <macro@linux-mips.org> Cc: Mikael Pettersson <mikpelinux@gmail.com> Cc: Josh Poulson <jopoulso@microsoft.com> Cc: Mihai Costache <v-micos@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: linux-pci@vger.kernel.org Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Dexuan Cui <decui@microsoft.com> Cc: Simon Xiao <sixiao@microsoft.com> Cc: Saeed Mahameed <saeedm@mellanox.com> Cc: Jork Loeser <Jork.Loeser@microsoft.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: devel@linuxdriverproject.org Cc: KY Srinivasan <kys@microsoft.com> Cc: Alan Cox <alan@linux.intel.com> Cc: Sakari Ailus <sakari.ailus@intel.com>, Cc: linux-media@vger.kernel.org Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712291406420.1899@nanos Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712291409460.1899@nanos
Thomas Gleixner [Fri, 29 Dec 2017 15:57:00 +0000 (16:57 +0100)]
x86/vector: Use IRQD_CAN_RESERVE flag
Set the new CAN_RESERVE flag when the initial reservation for an interrupt
happens. The flag is used in a subsequent patch to disable reservation mode
for a certain class of MSI devices.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Alexandru Chirvasitu <achirvasub@gmail.com> Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Dou Liyang <douly.fnst@cn.fujitsu.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Maciej W. Rozycki <macro@linux-mips.org> Cc: Mikael Pettersson <mikpelinux@gmail.com> Cc: Josh Poulson <jopoulso@microsoft.com> Cc: Mihai Costache <v-micos@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: linux-pci@vger.kernel.org Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Dexuan Cui <decui@microsoft.com> Cc: Simon Xiao <sixiao@microsoft.com> Cc: Saeed Mahameed <saeedm@mellanox.com> Cc: Jork Loeser <Jork.Loeser@microsoft.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: devel@linuxdriverproject.org Cc: KY Srinivasan <kys@microsoft.com> Cc: Alan Cox <alan@linux.intel.com> Cc: Sakari Ailus <sakari.ailus@intel.com>, Cc: linux-media@vger.kernel.org
Thomas Gleixner [Fri, 29 Dec 2017 15:44:34 +0000 (16:44 +0100)]
genirq: Introduce IRQD_CAN_RESERVE flag
Add a new flag to mark interrupts which can use reservation mode. This is
going to be used in subsequent patches to disable reservation mode for a
certain class of MSI devices.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Alexandru Chirvasitu <achirvasub@gmail.com> Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Dou Liyang <douly.fnst@cn.fujitsu.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Maciej W. Rozycki <macro@linux-mips.org> Cc: Mikael Pettersson <mikpelinux@gmail.com> Cc: Josh Poulson <jopoulso@microsoft.com> Cc: Mihai Costache <v-micos@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: linux-pci@vger.kernel.org Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Dexuan Cui <decui@microsoft.com> Cc: Simon Xiao <sixiao@microsoft.com> Cc: Saeed Mahameed <saeedm@mellanox.com> Cc: Jork Loeser <Jork.Loeser@microsoft.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: devel@linuxdriverproject.org Cc: KY Srinivasan <kys@microsoft.com> Cc: Alan Cox <alan@linux.intel.com> Cc: Sakari Ailus <sakari.ailus@intel.com>, Cc: linux-media@vger.kernel.org
Thomas Gleixner [Fri, 29 Dec 2017 09:42:10 +0000 (10:42 +0100)]
genirq/msi: Handle reactivation only on success
When analyzing the fallout of the x86 vector allocation rework it turned
out that the error handling in msi_domain_alloc_irqs() is broken.
If MSI_FLAG_MUST_REACTIVATE is set for a MSI domain then it clears the
activation flag for a successfully initialized msi descriptor. If a
subsequent initialization fails then the error handling code path does not
deactivate the interrupt because the activation flag got cleared.
Move the clearing of the activation flag outside of the initialization loop
so that an eventual failure can be cleaned up correctly.
Fixes: 22d0b12f3560 ("genirq/irqdomain: Add force reactivation flag to irq domains") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Alexandru Chirvasitu <achirvasub@gmail.com> Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Dou Liyang <douly.fnst@cn.fujitsu.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Maciej W. Rozycki <macro@linux-mips.org> Cc: Mikael Pettersson <mikpelinux@gmail.com> Cc: Josh Poulson <jopoulso@microsoft.com> Cc: Mihai Costache <v-micos@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: linux-pci@vger.kernel.org Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Dexuan Cui <decui@microsoft.com> Cc: Simon Xiao <sixiao@microsoft.com> Cc: Saeed Mahameed <saeedm@mellanox.com> Cc: Jork Loeser <Jork.Loeser@microsoft.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: devel@linuxdriverproject.org Cc: KY Srinivasan <kys@microsoft.com> Cc: Alan Cox <alan@linux.intel.com> Cc: Sakari Ailus <sakari.ailus@intel.com>, Cc: linux-media@vger.kernel.org
Linus Torvalds [Fri, 29 Dec 2017 19:54:15 +0000 (11:54 -0800)]
Merge tag 'pm-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"This fixes a schedutil cpufreq governor regression from the 4.14 cycle
that may cause a CPU idleness check to return incorrect results in
some cases which leads to suboptimal decisions (Joel Fernandes)"
* tag 'pm-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: schedutil: Use idle_calls counter of the remote CPU
Thomas Gleixner [Fri, 29 Dec 2017 15:29:15 +0000 (16:29 +0100)]
gpio: brcmstb: Make really use of the new lockdep class
The recent extension of irq_set_lockdep_class() with a second argument
added the new lockdep class to the mrcmstb driver, but used the already
existing lockdep class as second argument, which leaves the new lockdep
class defined but unused.
Use the new lockdep class as that's what the change intended to do.
Fixes: 39c3fd58952d ("kernel/irq: Extend lockdep class for request mutex") Reported-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andrew Lunn <andrew@lunn.ch> Cc: linus.walleij@linaro.org
1) IPv6 gre tunnels end up with different default features enabled
depending upon whether netlink or ioctls are used to bring them up.
Fix from Alexey Kodanev.
2) Fix read past end of user control message in RDS< from Avinash
Repaka.
3) Missing RCU barrier in mini qdisc code, from Cong Wang.
4) Missing policy put when reusing per-cpu route entries, from Florian
Westphal.
5) Handle nested PCI errors properly in bnx2x driver, from Guilherme G.
Piccoli.
6) Run nested transport mode IPSEC packets via tasklet, from Herbert
Xu.
7) Fix handling poll() for stream sockets in tipc, from Parthasarathy
Bhuvaragan.
8) Fix two stack-out-of-bounds issues in IPSEC, from Steffen Klassert.
9) Another zerocopy ubuf handling fix, from Willem de Bruijn.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
strparser: Call sock_owned_by_user_nocheck
sock: Add sock_owned_by_user_nocheck
skbuff: in skb_copy_ubufs unclone before releasing zerocopy
tipc: fix hanging poll() for stream sockets
sctp: Replace use of sockets_allocated with specified macro.
bnx2x: Improve reliability in case of nested PCI errors
tg3: Enable PHY reset in MTU change path for 5720
tg3: Add workaround to restrict 5762 MRRS to 2048
tg3: Update copyright
net: fec: unmap the xmit buffer that are not transferred by DMA
tipc: fix tipc_mon_delete() oops in tipc_enable_bearer() error path
tipc: error path leak fixes in tipc_enable_bearer()
RDS: Check cmsg_len before dereferencing CMSG_DATA
tcp: Avoid preprocessor directives in tracepoint macro args
tipc: fix memory leak of group member when peer node is lost
net: sched: fix possible null pointer deref in tcf_block_put
tipc: base group replicast ack counter on number of actual receivers
net_sched: fix a missing rcu barrier in mini_qdisc_pair_swap()
net: phy: micrel: ksz9031: reconfigure autoneg after phy autoneg workaround
ip6_gre: fix device features for ioctl setup
...
Linus Torvalds [Fri, 29 Dec 2017 07:16:24 +0000 (23:16 -0800)]
Merge tag 'drm-fixes-for-v4.15-rc6' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"nouveau and i915 regression fixes"
* tag 'drm-fixes-for-v4.15-rc6' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: fix race when adding delayed work items
i915: Reject CCS modifiers for pipe C on Geminilake
drm/i915/gvt: Fix pipe A enable as default for vgpu
Linus Torvalds [Fri, 29 Dec 2017 07:14:47 +0000 (23:14 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One more fix for the runtime PM clk patches. We're calling a runtime
PM API that may schedule from somewhere that we can't do that. We
change to the async version of pm_runtime_put() to fix it"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: use atomic runtime pm api in clk_core_is_enabled
Linus Torvalds [Fri, 29 Dec 2017 07:09:45 +0000 (23:09 -0800)]
Merge tag 'led_fixes_for_4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fix from Jacek Anaszewski:
"A single LED fix for brightness setting when delay_off is 0"
* tag 'led_fixes_for_4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
led: core: Fix brightness setting when setting delay_off=0
Linus Torvalds [Fri, 29 Dec 2017 07:06:01 +0000 (23:06 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"This is the next batch of for-rc patches from RDMA. It includes the
fix for the ipoib regression I mentioned last time, and the result of
a fairly major debugging effort to get iser working reliably on cxgb4
hardware - it turns out the cxgb4 driver was not handling QP error
flushing properly causing iser to fail.
- cxgb4 fix for an iser testing failure as debugged by Steve and
Sagi. The problem was a driver bug in the handling of shutting down
a QP.
- Various vmw_pvrdma fixes for bogus WARN_ON, missed resource free on
error unwind and a use after free bug
- Improper congestion counter values on mlx5 when link aggregation is
enabled
- ipoib lockdep regression introduced in this merge window
- hfi1 regression supporting the device in a VM introduced in a
recent patch
- Typo that breaks future uAPI compatibility in the verbs core
- More SELinux related oops fixing
- Fix an oops during error unwind in mlx5"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/mlx5: Fix mlx5_ib_alloc_mr error flow
IB/core: Verify that QP is security enabled in create and destroy
IB/uverbs: Fix command checking as part of ib_uverbs_ex_modify_qp()
IB/mlx5: Serialize access to the VMA list
IB/hfi: Only read capability registers if the capability exists
IB/ipoib: Fix lockdep issue found on ipoib_ib_dev_heavy_flush
IB/mlx5: Fix congestion counters in LAG mode
RDMA/vmw_pvrdma: Avoid use after free due to QP/CQ/SRQ destroy
RDMA/vmw_pvrdma: Use refcount_dec_and_test to avoid warning
RDMA/vmw_pvrdma: Call ib_umem_release on destroy QP path
iw_cxgb4: when flushing, complete all wrs in a chain
iw_cxgb4: reflect the original WR opcode in drain cqes
iw_cxgb4: Only validate the MSN for successful completions
David S. Miller [Thu, 28 Dec 2017 19:28:23 +0000 (14:28 -0500)]
Merge branch 'strparser-Fix-lockdep-issue'
Tom Herbert says:
====================
strparser: Fix lockdep issue
When sock_owned_by_user returns true in strparser. Fix is to add and
call sock_owned_by_user_nocheck since the check for owned by user is
not an error condition in this case.
====================
Fixes: 43a0c6751a322847 ("strparser: Stream parser for messages") Reported-by: syzbot <syzkaller@googlegroups.com> Reported-and-tested-by: <syzbot+c91c53af67f9ebe599a337d2e70950366153b295@syzkaller.appspotmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Thu, 28 Dec 2017 19:00:44 +0000 (11:00 -0800)]
strparser: Call sock_owned_by_user_nocheck
strparser wants to check socket ownership without producing any
warnings. As indicated by the comment in the code, it is permissible
for owned_by_user to return true.
Fixes: 43a0c6751a322847 ("strparser: Stream parser for messages") Reported-by: syzbot <syzkaller@googlegroups.com> Reported-and-tested-by: <syzbot+c91c53af67f9ebe599a337d2e70950366153b295@syzkaller.appspotmail.com> Signed-off-by: Tom Herbert <tom@quantonium.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Thu, 28 Dec 2017 17:38:13 +0000 (12:38 -0500)]
skbuff: in skb_copy_ubufs unclone before releasing zerocopy
skb_copy_ubufs must unclone before it is safe to modify its
skb_shared_info with skb_zcopy_clear.
Commit b90ddd568792 ("skbuff: skb_copy_ubufs must release uarg even
without user frags") ensures that all skbs release their zerocopy
state, even those without frags.
But I forgot an edge case where such an skb arrives that is cloned.
The stack does not build such packets. Vhost/tun skbs have their
frags orphaned before cloning. TCP skbs only attach zerocopy state
when a frag is added.
But if TCP packets can be trimmed or linearized, this might occur.
Tracing the code I found no instance so far (e.g., skb_linearize
ends up calling skb_zcopy_clear if !skb->data_len).
Still, it is non-obvious that no path exists. And it is fragile to
rely on this.
Fixes: b90ddd568792 ("skbuff: skb_copy_ubufs must release uarg even without user frags") Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 42b531de17d2f6 ("tipc: Fix missing connection request
handling"), we replaced unconditional wakeup() with condtional
wakeup for clients with flags POLLIN | POLLRDNORM | POLLRDBAND.
This breaks the applications which do a connect followed by poll
with POLLOUT flag. These applications are not woken when the
connection is ESTABLISHED and hence sleep forever.
In this commit, we fix it by including the POLLOUT event for
sockets in TIPC_CONNECTING state.
Fixes: 42b531de17d2f6 ("tipc: Fix missing connection request handling") Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lukas Bulwahn [Tue, 26 Dec 2017 21:27:20 +0000 (15:27 -0600)]
objtool: Fix Clang enum conversion warning
Fix the following Clang enum conversion warning:
arch/x86/decode.c:141:20: error: implicit conversion from enumeration
type 'enum op_src_type' to different enumeration
type 'enum op_dest_type' [-Werror,-Wenum-conversion]
op->dest.type = OP_SRC_REG;
~ ^~~~~~~~~~
It just happened to work before because OP_SRC_REG and OP_DEST_REG have
the same value.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Reviewed-by: Nicholas Mc Guire <der.herr@hofr.at> Reviewed-by: Nick Desaulniers <nick.desaulniers@gmail.com> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: baa41469a7b9 ("objtool: Implement stack validation 2.0") Link: http://lkml.kernel.org/r/b4156c5738bae781c392e7a3691aed4514ebbdf2.1514323568.git.jpoimboe@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
This was seen when running an upstream kernel on Acer Chromebook R11. The
system was unstable as result.
Guard the log message with __printk_ratelimit to reduce the impact. This
won't prevent the interrupt storm from happening, but at least the system
remains stable.
Joel Fernandes [Thu, 21 Dec 2017 01:22:45 +0000 (02:22 +0100)]
cpufreq: schedutil: Use idle_calls counter of the remote CPU
Since the recent remote cpufreq callback work, its possible that a cpufreq
update is triggered from a remote CPU. For single policies however, the current
code uses the local CPU when trying to determine if the remote sg_cpu entered
idle or is busy. This is incorrect. To remedy this, compare with the nohz tick
idle_calls counter of the remote CPU.
Fixes: 674e75411fc2 (sched: cpufreq: Allow remote cpufreq callbacks) Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Joel Fernandes <joelaf@google.com> Cc: 4.14+ <stable@vger.kernel.org> # 4.14+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Andrew Lunn [Sat, 2 Dec 2017 17:11:04 +0000 (18:11 +0100)]
kernel/irq: Extend lockdep class for request mutex
The IRQ code already has support for lockdep class for the lock mutex
in an interrupt descriptor. Extend this to add a second class for the
request mutex in the descriptor. Not having a class is resulting in
false positive splats in some code paths.
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Two small fixes for bpftool. Fix otherwise broken output if any of
the system calls failed when listing maps in json format and instead
of bailing out, skip maps or progs that disappeared between fetching
next id and getting an fd for that id, both from Jakub.
2) Small fix in BPF selftests to respect LLC passed from command line
when testing for -mcpu=probe presence, from Quentin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Engelhardt [Mon, 25 Dec 2017 02:43:53 +0000 (03:43 +0100)]
sparc64: repair calling incorrect hweight function from stubs
Commit v4.12-rc4-1-g9289ea7f952b introduced a mistake that made the
64-bit hweight stub call the 16-bit hweight function.
Fixes: 9289ea7f952b ("sparc64: Use indirect calls in hamming weight stubs") Signed-off-by: Jan Engelhardt <jengelh@inai.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Nitzan Carmi [Tue, 26 Dec 2017 09:20:20 +0000 (11:20 +0200)]
IB/mlx5: Fix mlx5_ib_alloc_mr error flow
ibmr.device is being set only after ib_alloc_mr() is
(successfully) complete. Therefore, in case mlx5_core_create_mkey()
return with error, the error flow calls mlx5_free_priv_descs()
which uses ibmr.device (which doesn't exist yet), causing
a NULL dereference oops.
To fix this, the IB device should be set in the mr struct earlier
stage (e.g. prior to calling mlx5_core_create_mkey()).
Fixes: 8a187ee52b04 ("IB/mlx5: Support the new memory registration API") Signed-off-by: Max Gurtovoy <maxg@mellanox.com> Signed-off-by: Nitzan Carmi <nitzanc@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Moni Shoua [Sun, 24 Dec 2017 11:54:58 +0000 (13:54 +0200)]
IB/core: Verify that QP is security enabled in create and destroy
The XRC target QP create flow sets up qp_sec only if there is an IB link with
LSM security enabled. However, several other related uAPI entry points blindly
follow the qp_sec NULL pointer, resulting in a possible oops.
Check for NULL before using qp_sec.
Cc: <stable@vger.kernel.org> # v4.12 Fixes: d291f1a65232 ("IB/core: Enforce PKey security on QPs") Reviewed-by: Daniel Jurgens <danielj@mellanox.com> Signed-off-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Moni Shoua [Sun, 24 Dec 2017 11:54:57 +0000 (13:54 +0200)]
IB/uverbs: Fix command checking as part of ib_uverbs_ex_modify_qp()
If the input command length is larger than the kernel supports an error should
be returned in case the unsupported bytes are not cleared, instead of the
other way aroudn. This matches what all other callers of ib_is_udata_cleared
do and will avoid user ABI problems in the future.
Cc: <stable@vger.kernel.org> # v4.10 Fixes: 189aba99e700 ("IB/uverbs: Extend modify_qp and support packet pacing") Reviewed-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Majd Dibbiny [Sun, 24 Dec 2017 11:54:56 +0000 (13:54 +0200)]
IB/mlx5: Serialize access to the VMA list
User-space applications can do mmap and munmap directly at
any time.
Since the VMA list is not protected with a mutex, concurrent
accesses to the VMA list from the mmap and munmap can cause
data corruption. Add a mutex around the list.
Cc: <stable@vger.kernel.org> # v4.7 Fixes: 7c2344c3bbf9 ("IB/mlx5: Implements disassociate_ucontext API") Reviewed-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Linus Torvalds [Wed, 27 Dec 2017 21:06:57 +0000 (13:06 -0800)]
Merge tag 'trace-v4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"While doing tests on tracing over the network, I found that the
packets were getting corrupted.
In the process I found three bugs.
One was the culprit, but the other two scared me. After deeper
investigation, they were not as major as I thought they were, due to a
signed compared to an unsigned that prevented a negative number from
doing actual harm.
The two bigger bugs:
- Mask the ring buffer data page length. There are data flags at the
high bits of the length field. These were not cleared via the
length function, and the length could return a negative number.
(Although the number returned was unsigned, but was assigned to a
signed number) Luckily, this value was compared to PAGE_SIZE which
is unsigned and kept it from entering the path that could have
caused damage.
- Check the page usage before reusing the ring buffer reader page.
TCP increments the page ref when passing the page off to the
network. The page is passed back to the ring buffer for use on
free. But the page could still be in use by the TCP stack.
Minor bugs:
- Related to the first bug. No need to clear out the unused ring
buffer data before sending to user space. It is now done by the
ring buffer code itself.
- Reset pointers after free on error path. There were some cases in
the error path that pointers were freed but not set to NULL, and
could have them freed again, having a pointer freed twice"
* tag 'trace-v4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix possible double free on failure of allocating trace buffer
tracing: Fix crash when it fails to alloc ring buffer
ring-buffer: Do no reuse reader page if still in use
tracing: Remove extra zeroing out of the ring buffer page
ring-buffer: Mask out the info bits when returning buffer page length
Linus Torvalds [Wed, 27 Dec 2017 20:59:27 +0000 (12:59 -0800)]
Merge tag 'sound-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"It seems that Santa overslept with a bunch of gifts; the majority of
changes here are various device-specific ASoC fixes, most notably the
revert of rcar IOMMU support and fsl_ssi AC97 fixes, but also lots of
small fixes for codecs. Besides that, the usual HD-audio quirks and
fixes are included, too"
* tag 'sound-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (31 commits)
ALSA: hda - Fix missing COEF init for ALC225/295/299
ALSA: hda: Drop useless WARN_ON()
ALSA: hda - change the location for one mic on a Lenovo machine
ALSA: hda - fix headset mic detection issue on a Dell machine
ALSA: hda - Add MIC_NO_PRESENCE fixup for 2 HP machines
ASoC: rsnd: fixup ADG register mask
ASoC: rt5514-spi: only enable wakeup when fully initialized
ASoC: nau8825: fix issue that pop noise when start capture
ASoC: rt5663: Fix the wrong result of the first jack detection
ASoC: rsnd: ssi: fix race condition in rsnd_ssi_pointer_update
ASoC: Intel: Change kern log level to avoid unwanted messages
ASoC: atmel-classd: select correct Kconfig symbol
ASoC: wm_adsp: Fix validation of firmware and coeff lengths
ASoC: Intel: Skylake: Do not check dev_type for dmic link type
ASoC: rockchip: disable clock on error
ASoC: tlv320aic31xx: Fix GPIO1 register definition
ASoC: codecs: msm8916-wcd: Fix supported formats
ASoC: fsl_asrc: Fix typo in a field define
ASoC: rsnd: ssiu: clear SSI_MODE for non TDM Extended modes
ASoC: da7218: Correct IRQ level in DT binding example
...
Matthieu CASTET [Tue, 12 Dec 2017 10:10:44 +0000 (11:10 +0100)]
led: core: Fix brightness setting when setting delay_off=0
With the current code, the following sequence won't work :
echo timer > trigger
echo 0 > delay_off
* at this point we call
** led_delay_off_store
** led_blink_set
*** stop timer
** led_blink_setup
** led_set_software_blink
*** if !delay_on, led off
*** if !delay_off, set led_set_brightness_nosleep <--- LED_BLINK_SW is set but timer is stop
*** otherwise start timer/set LED_BLINK_SW flag
echo xxx > brightness
* led_set_brightness
** if LED_BLINK_SW
*** if brightness=0, led off
*** else apply brightness if next timer <--- timer is stop, and will never apply new setting
** otherwise set led_set_brightness_nosleep
To fix that, when we delete the timer, we should clear LED_BLINK_SW.
Cc: linux-leds@vger.kernel.org Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com> Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Thomas Gleixner [Wed, 27 Dec 2017 18:45:31 +0000 (19:45 +0100)]
perf/x86/intel: Plug memory leak in intel_pmu_init()
A recent commit introduced an extra merge_attr() call in the skylake
branch, which causes a memory leak.
Store the pointer to the extra allocated memory and free it at the end of
the function.
Fixes: a5df70c354c2 ("perf/x86: Only show format attributes when supported") Reported-by: Tommi Rantala <tommi.t.rantala@nokia.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andi Kleen <ak@linux.intel.com>
tracing: Fix possible double free on failure of allocating trace buffer
Jing Xia and Chunyan Zhang reported that on failing to allocate part of the
tracing buffer, memory is freed, but the pointers that point to them are not
initialized back to NULL, and later paths may try to free the freed memory
again. Jing and Chunyan fixed one of the locations that does this, but
missed a spot.
Jing Xia [Tue, 26 Dec 2017 07:12:53 +0000 (15:12 +0800)]
tracing: Fix crash when it fails to alloc ring buffer
Double free of the ring buffer happens when it fails to alloc new
ring buffer instance for max_buffer if TRACER_MAX_TRACE is configured.
The root cause is that the pointer is not set to NULL after the buffer
is freed in allocate_trace_buffers(), and the freeing of the ring
buffer is invoked again later if the pointer is not equal to Null,
as:
//if trace_buffer is not null, free again
|-ring_buffer_free(buf->buffer)
|-rb_free_cpu_buffer(buffer->buffers[cpu])
// ring_buffer_per_cpu is null, and
// crash in ring_buffer_per_cpu->pages
ring-buffer: Do no reuse reader page if still in use
To free the reader page that is allocated with ring_buffer_alloc_read_page(),
ring_buffer_free_read_page() must be called. For faster performance, this
page can be reused by the ring buffer to avoid having to free and allocate
new pages.
The issue arises when the page is used with a splice pipe into the
networking code. The networking code may up the page counter for the page,
and keep it active while sending it is queued to go to the network. The
incrementing of the page ref does not prevent it from being reused in the
ring buffer, and this can cause the page that is being sent out to the
network to be modified before it is sent by reading new data.
Add a check to the page ref counter, and only reuse the page if it is not
being used anywhere else.
Cc: stable@vger.kernel.org Fixes: 73a757e63114d ("ring-buffer: Return reader page back into existing ring buffer") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
tracing: Remove extra zeroing out of the ring buffer page
The ring_buffer_read_page() takes care of zeroing out any extra data in the
page that it returns. There's no need to zero it out again from the
consumer. It was removed from one consumer of this function, but
read_buffers_splice_read() did not remove it, and worse, it contained a
nasty bug because of it.
Cc: stable@vger.kernel.org Fixes: 2711ca237a084 ("ring-buffer: Move zeroing out excess in page to ring buffer code") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Dave Airlie [Wed, 27 Dec 2017 19:20:07 +0000 (05:20 +1000)]
Merge tag 'drm-intel-fixes-2017-12-22-1' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
GLK pipe C related fix, and a gvt fix.
* tag 'drm-intel-fixes-2017-12-22-1' of git://anongit.freedesktop.org/drm/drm-intel:
i915: Reject CCS modifiers for pipe C on Geminilake
drm/i915/gvt: Fix pipe A enable as default for vgpu
ring-buffer: Mask out the info bits when returning buffer page length
Two info bits were added to the "commit" part of the ring buffer data page
when returned to be consumed. This was to inform the user space readers that
events have been missed, and that the count may be stored at the end of the
page.
What wasn't handled, was the splice code that actually called a function to
return the length of the data in order to zero out the rest of the page
before sending it up to user space. These data bits were returned with the
length making the value negative, and that negative value was not checked.
It was compared to PAGE_SIZE, and only used if the size was less than
PAGE_SIZE. Luckily PAGE_SIZE is unsigned long which made the compare an
unsigned compare, meaning the negative size value did not end up causing a
large portion of memory to be randomly zeroed out.
Cc: stable@vger.kernel.org Fixes: 66a8cb95ed040 ("ring-buffer: Add place holder recording of dropped events") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Tonghao Zhang [Fri, 22 Dec 2017 18:15:20 +0000 (10:15 -0800)]
sctp: Replace use of sockets_allocated with specified macro.
The patch(180d8cd942ce) replaces all uses of struct sock fields'
memory_pressure, memory_allocated, sockets_allocated, and sysctl_mem
to accessor macros. But the sockets_allocated field of sctp sock is
not replaced at all. Then replace it now for unifying the code.
Fixes: 180d8cd942ce ("foundations of per-cgroup memory pressure controlling.") Cc: Glauber Costa <glommer@parallels.com> Signed-off-by: Tonghao Zhang <zhangtonghao@didichuxing.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x: Improve reliability in case of nested PCI errors
While in recovery process of PCI error (called EEH on PowerPC arch),
another PCI transaction could be corrupted causing a situation of
nested PCI errors. Also, this scenario could be reproduced with
error injection mechanisms (for debug purposes).
We observe that in case of nested PCI errors, bnx2x might attempt to
initialize its shmem and cause a kernel crash due to bad addresses
read from MCP. Multiple different stack traces were observed depending
on the point the second PCI error happens.
This patch avoids the crashes by:
* failing PCI recovery in case of nested errors (since multiple
PCI errors in a row are not expected to lead to a functional
adapter anyway), and by,
* preventing access to adapter FW when MCP is failed (we mark it as
failed when shmem cannot get initialized properly).
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com> Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Acked-by: Shahed Shaikh <Shahed.Shaikh@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A customer noticed RX path hang when MTU is changed on the fly while
running heavy traffic with NCSI enabled for 5717 and 5719. Since 5720
belongs to same ASIC family, we observed same issue and same fix
could solve this problem for 5720.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
One of AMD based server with 5762 hangs with jumbo frame traffic.
This AMD platform has southbridge limitation which is restricting MRRS
to 4000. As a work around, driver to restricts the MRRS to 2048 for
this particular 5762 NX1 card.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1) Check for valid id proto in validate_tmpl(), otherwise
we may trigger a warning in xfrm_state_fini().
From Cong Wang.
2) Fix a typo on XFRMA_OUTPUT_MARK policy attribute.
From Michal Kubecek.
3) Verify the state is valid when encap_type < 0,
otherwise we may crash on IPsec GRO .
From Aviv Heller.
4) Fix stack-out-of-bounds read on socket policy lookup.
We access the flowi of the wrong address family in the
IPv4 mapped IPv6 case, fix this by catching address
family missmatches before we do the lookup.
5) fix xfrm_do_migrate() with AEAD to copy the geniv
field too. Otherwise the state is not fully initialized
and migration fails. From Antony Antony.
6) Fix stack-out-of-bounds with misconfigured transport
mode policies. Our policy template validation is not
strict enough. It is possible to configure policies
with transport mode template where the address family
of the template does not match the selectors address
family. Fix this by refusing such a configuration,
address family can not change on transport mode.
7) Fix a policy reference leak when reusing pcpu xdst
entry. From Florian Westphal.
8) Reinject transport-mode packets through tasklet,
otherwise it is possible to reate a recursion
loop. From Herbert Xu.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fugang Duan [Fri, 22 Dec 2017 09:12:09 +0000 (17:12 +0800)]
net: fec: unmap the xmit buffer that are not transferred by DMA
The enet IP only support 32 bit, it will use swiotlb buffer to do dma
mapping when xmit buffer DMA memory address is bigger than 4G in i.MX
platform. After stress suspend/resume test, it will print out:
log:
[12826.352864] fec 5b040000.ethernet: swiotlb buffer is full (sz: 191 bytes)
[12826.359676] DMA: Out of SW-IOMMU space for 191 bytes at device 5b040000.ethernet
[12826.367110] fec 5b040000.ethernet eth0: Tx DMA memory map failed
The issue is that the ready xmit buffers that are dma mapped but DMA still
don't copy them into fifo, once MAC restart, these DMA buffers are not unmapped.
So it should check the dma mapping buffer and unmap them.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tommi Rantala [Fri, 22 Dec 2017 07:35:17 +0000 (09:35 +0200)]
tipc: fix tipc_mon_delete() oops in tipc_enable_bearer() error path
Calling tipc_mon_delete() before the monitor has been created will oops.
This can happen in tipc_enable_bearer() error path if tipc_disc_create()
fails.
Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tommi Rantala [Fri, 22 Dec 2017 07:35:16 +0000 (09:35 +0200)]
tipc: error path leak fixes in tipc_enable_bearer()
Fix memory leak in tipc_enable_bearer() if enable_media() fails, and
cleanup with bearer_disable() if tipc_mon_create() fails.
Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Avinash Repaka [Fri, 22 Dec 2017 04:17:04 +0000 (20:17 -0800)]
RDS: Check cmsg_len before dereferencing CMSG_DATA
RDS currently doesn't check if the length of the control message is
large enough to hold the required data, before dereferencing the control
message data. This results in following crash:
BUG: KASAN: stack-out-of-bounds in rds_rdma_bytes net/rds/send.c:1013
[inline]
BUG: KASAN: stack-out-of-bounds in rds_sendmsg+0x1f02/0x1f90
net/rds/send.c:1066
Read of size 8 at addr ffff8801c928fb70 by task syzkaller455006/3157
Daniel Thompson [Thu, 21 Dec 2017 13:06:15 +0000 (15:06 +0200)]
usb: xhci: Add XHCI_TRUST_TX_LENGTH for Renesas uPD720201
When plugging in a USB webcam I see the following message:
xhci_hcd 0000:04:00.0: WARN Successful completion on short TX: needs
XHCI_TRUST_TX_LENGTH quirk?
handle_tx_event: 913 callbacks suppressed
All is quiet again with this patch (and I've done a fair but of soak
testing with the camera since).
The issue is caused by the xhci ring structures being reallocated
when the system is resumed, but pointers to the old structures
being retained in the debugfs files "private" field:
The proposed patch fixes this issue by storing a pointer to the xhci_ring
field in the xhci device structure in debugfs rather than directly
storing a pointer to the xhci_ring.
Mathias Nyman [Thu, 21 Dec 2017 13:06:13 +0000 (15:06 +0200)]
xhci: Fix xhci debugfs NULL pointer dereference in resume from hibernate
Free the virt_device and its debugfs_private member together.
When resuming from hibernate the .free_dev callback unconditionally
freed the debugfs_private member, but could leave virt_device intact.
This triggered a NULL pointer dereference after resume when usbmuxd
sent a USBDEVFS_SETCONFIGURATION ioctl to a device, trying to add a
endpoint debugfs entry to a already freed debugfs_private pointer.
Fixes: 02b6fdc2a153 ("usb: xhci: Add debugfs interface for xHCI driver") Reported-by: Alexander Kappner <agk@godking.net> Tested-by: Alexander Kappner <agk@godking.net> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge tag 'usb-serial-4.15-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes
USB-serial fixes for v4.15-rc6
Here are some new device ids for ftdi_sio, option and qcserial.
Note that the qcserial patch enables the SetControlLineState request
(used to raise DTR/RTS) for the GPS interface of all devices using the
Sierra Wireless layout. This was required for the Sierra Wireless EM7565
and has been tested using several other modems as well.
All but the final commit have been in linux-next without any reported
issues.
Takashi Iwai [Wed, 27 Dec 2017 07:53:59 +0000 (08:53 +0100)]
ALSA: hda - Fix missing COEF init for ALC225/295/299
There was a long-standing problem on HP Spectre X360 with Kabylake
where it lacks of the front speaker output in some situations. Also
there are other products showing the similar behavior. The culprit
seems to be the missing COEF setup on ALC codecs, ALC225/295/299,
which are all compatible.
This patch adds the proper COEF setup (to initialize idx 0x67 / bits
0x3000) for addressing the issue.
Linus Torvalds [Wed, 27 Dec 2017 02:22:20 +0000 (18:22 -0800)]
Merge tag 'hwmon-for-linus-v4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Handle errors from thermal subsystem"
* tag 'hwmon-for-linus-v4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: Deal with errors from the thermal subsystem
Dong Aisheng [Fri, 22 Dec 2017 09:46:04 +0000 (17:46 +0800)]
clk: use atomic runtime pm api in clk_core_is_enabled
Current clk_pm_runtime_put is using pm_runtime_put_sync which
is not safe to be called in clk_core_is_enabled as it should
be able to run in atomic context.
Thus use pm_runtime_put instead which is atomic safe.
Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Ulf Hansson <ulf.hansson@linaro.org> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Fixes: 9a34b45397e5 ("clk: Add support for runtime PM") Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Mat Martineau [Thu, 21 Dec 2017 18:29:09 +0000 (10:29 -0800)]
tcp: Avoid preprocessor directives in tracepoint macro args
Using a preprocessor directive to check for CONFIG_IPV6 in the middle of
a DECLARE_EVENT_CLASS macro's arg list causes sparse to report a series
of errors:
./include/trace/events/tcp.h:68:1: error: directive in argument list
./include/trace/events/tcp.h:75:1: error: directive in argument list
./include/trace/events/tcp.h:144:1: error: directive in argument list
./include/trace/events/tcp.h:151:1: error: directive in argument list
./include/trace/events/tcp.h:216:1: error: directive in argument list
./include/trace/events/tcp.h:223:1: error: directive in argument list
./include/trace/events/tcp.h:274:1: error: directive in argument list
./include/trace/events/tcp.h:281:1: error: directive in argument list
Once sparse finds an error, it stops printing warnings for the file it
is checking. This masks any sparse warnings that would normally be
reported for the core TCP code.
Instead, handle the preprocessor conditionals in a couple of auxiliary
macros. This also has the benefit of reducing duplicate code.
Cc: David Ahern <dsahern@gmail.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij [Tue, 5 Dec 2017 08:36:14 +0000 (09:36 +0100)]
hwmon: Deal with errors from the thermal subsystem
If the thermal subsystem returne -EPROBE_DEFER or any other error
when hwmon calls devm_thermal_zone_of_sensor_register(), this is
silently ignored.
I ran into this with an incorrectly defined thermal zone, making
it non-existing and thus this call failed with -EPROBE_DEFER
assuming it would appear later. The sensor was still added
which is incorrect: sensors must strictly be added after the
thermal zones, so deferred probe must be respected.
Jon Maloy [Thu, 21 Dec 2017 13:36:34 +0000 (14:36 +0100)]
tipc: fix memory leak of group member when peer node is lost
When a group member receives a member WITHDRAW event, this might have
two reasons: either the peer member is leaving the group, or the link
to the member's node has been lost.
In the latter case we need to issue a DOWN event to the user right away,
and let function tipc_group_filter_msg() perform delete of the member
item. However, in this case we miss to change the state of the member
item to MBR_LEAVING, so the member item is not deleted, and we have a
memory leak.
We now separate better between the four sub-cases of a WITHRAW event
and make sure that each case is handled correctly.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy [Thu, 21 Dec 2017 12:07:11 +0000 (13:07 +0100)]
tipc: base group replicast ack counter on number of actual receivers
In commit 2f487712b893 ("tipc: guarantee that group broadcast doesn't
bypass group unicast") we introduced a mechanism that requires the first
(replicated) broadcast sent after a unicast to be acknowledged by all
receivers before permitting sending of the next (true) broadcast.
The counter for keeping track of the number of acknowledges to expect
is based on the tipc_group::member_cnt variable. But this misses that
some of the known members may not be ready for reception, and will never
acknowledge the message, either because they haven't fully joined the
group or because they are leaving the group. Such members are identified
by not fulfilling the condition tested for in the function
tipc_group_is_enabled().
We now set the counter for the actual number of acks to receive at the
moment the message is sent, by just counting the number of recipients
satisfying the tipc_group_is_enabled() test.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Thu, 21 Dec 2017 07:26:24 +0000 (23:26 -0800)]
net_sched: fix a missing rcu barrier in mini_qdisc_pair_swap()
The rcu_barrier_bh() in mini_qdisc_pair_swap() is to wait for
flying RCU callback installed by a previous mini_qdisc_pair_swap(),
however we miss it on the tp_head==NULL path, which leads to that
the RCU callback still uses miniq_old->rcu after it is freed together
with qdisc in qdisc_graft(). So just add it on that path too.
Fixes: 46209401f8f6 ("net: core: introduce mini_Qdisc and eliminate usage of tp->q for clsact fastpath ") Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com> Tested-by: Jakub Kicinski <jakub.kicinski@netronome.com> Cc: Jiri Pirko <jiri@mellanox.com> Cc: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: micrel: ksz9031: reconfigure autoneg after phy autoneg workaround
Under some circumstances driver will perform PHY reset in
ksz9031_read_status() to fix autoneg failure case (idle error count =
0xFF). When this happens ksz9031 will not detect link status change any
more when connecting to Netgear 1G switch (link can be recovered sometimes by
restarting netdevice "ifconfig down up"). Reproduced with TI am572x board
equipped with ksz9031 PHY while connecting to Netgear 1G switch.
Fix the issue by reconfiguring autonegotiation after PHY reset in
ksz9031_read_status().
Fixes: d2fd719bcb0e ("net/phy: micrel: Add workaround for bad autoneg") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Kodanev [Wed, 20 Dec 2017 16:36:03 +0000 (19:36 +0300)]
ip6_gre: fix device features for ioctl setup
When ip6gre is created using ioctl, its features, such as
scatter-gather, GSO and tx-checksumming will be turned off:
# ip -f inet6 tunnel add gre6 mode ip6gre remote fd00::1
# ethtool -k gre6 (truncated output)
tx-checksumming: off
scatter-gather: off
tcp-segmentation-offload: off
generic-segmentation-offload: off [requested on]
But when netlink is used, they will be enabled:
# ip link add gre6 type ip6gre remote fd00::1
# ethtool -k gre6 (truncated output)
tx-checksumming: on
scatter-gather: on
tcp-segmentation-offload: on
generic-segmentation-offload: on
This results in a loss of performance when gre6 is created via ioctl.
The issue was found with LTP/gre tests.
Fix it by moving the setup of device features to a separate function
and invoke it with ndo_init callback because both netlink and ioctl
will eventually call it via register_netdevice():
The moved code also contains two minor style fixes:
* removed needless tab from GRE6_FEATURES on NETIF_F_HIGHDMA line.
* fixed the issue reported by checkpatch: "Unnecessary parentheses around
'nt->encap.type == TUNNEL_ENCAP_NONE'"
Fixes: ac4eb009e477 ("ip6gre: Add support for basic offloads offloads excluding GSO") Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 20 Dec 2017 23:21:34 +0000 (23:21 +0000)]
phylink: ensure AN is enabled
Ensure that we mark AN as enabled at boot time, rather than leaving
it disabled. This is noticable if your SFP module is fiber, and
it supports faster speeds than 1G with 2.5G support in place.
Fixes: 9525ae83959b ("phylink: add phylink infrastructure") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 20 Dec 2017 23:21:28 +0000 (23:21 +0000)]
phylink: ensure the PHY interface mode is appropriately set
When setting the ethtool settings, ensure that the validated PHY
interface mode is propagated to the current link settings, so that
2500BaseX can be selected.
Fixes: 9525ae83959b ("phylink: add phylink infrastructure") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 23 Dec 2017 21:47:22 +0000 (13:47 -0800)]
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"These fixes are all tagged for -stable and have received a build
success notification from the kbuild robot.
- NVDIMM namespaces, configured to enforce 1GB alignment, fail to
initialize on platforms that mis-align the start or end of the
physical address range.
- The Linux implementation of the BTT (Block Translation Table) is
incompatible with the UEFI 2.7 definition of the BTT format. The
BTT layers a software atomic sector semantic on top of an NVDIMM
namespace. Linux needs to be compatible with the UEFI definition to
enable boot support or any pre-OS access of data on a BTT enabled
namespace.
- A fix for ACPI SMART notification events, this allows a userspace
monitor to register for health events rather than poll. This has
been broken since it was initially merged as the unit test
inadvertently worked around the problem. The urgency for fixing
this during the -rc series is driven by how expensive it is to poll
for this data (System Management Mode entry)"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm, btt: Fix an incompatibility in the log layout
libnvdimm, btt: add a couple of missing kernel-doc lines
libnvdimm, dax: fix 1GB-aligned namespaces vs physical misalignment
libnvdimm, pfn: fix start_pad handling for aligned namespaces
acpi, nfit: fix health event notification
Thomas Gleixner [Fri, 15 Dec 2017 19:35:11 +0000 (20:35 +0100)]
x86/ldt: Make the LDT mapping RO
Now that the LDT mapping is in a known area when PAGE_TABLE_ISOLATION is
enabled its a primary target for attacks, if a user space interface fails
to validate a write address correctly. That can never happen, right?
The SDM states:
If the segment descriptors in the GDT or an LDT are placed in ROM, the
processor can enter an indefinite loop if software or the processor
attempts to update (write to) the ROM-based segment descriptors. To
prevent this problem, set the accessed bits for all segment descriptors
placed in a ROM. Also, remove operating-system or executive code that
attempts to modify segment descriptors located in ROM.
So its a valid approach to set the ACCESS bit when setting up the LDT entry
and to map the table RO. Fixup the selftest so it can handle that new mode.
Remove the manual ACCESS bit setter in set_tls_desc() as this is now
pointless. Folded the patch from Peter Ziljstra.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Ingo Molnar <mingo@kernel.org>
Thomas Gleixner [Mon, 4 Dec 2017 14:08:06 +0000 (15:08 +0100)]
x86/mm/dump_pagetables: Allow dumping current pagetables
Add two debugfs files which allow to dump the pagetable of the current
task.
current_kernel dumps the regular page table. This is the page table which
is normally shared between kernel and user space. If kernel page table
isolation is enabled this is the kernel space mapping.
If kernel page table isolation is enabled the second file, current_user,
dumps the user space page table.
These files allow to verify the resulting page tables for page table
isolation, but even in the normal case its useful to be able to inspect
user space page tables of current for debugging purposes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Laight <David.Laight@aculab.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Eduardo Valentin <eduval@amazon.com> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Will Deacon <will.deacon@arm.com> Cc: aliguori@amazon.com Cc: daniel.gruss@iaik.tugraz.at Cc: hughd@google.com Cc: keescook@google.com Cc: linux-mm@kvack.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Borislav Petkov [Mon, 4 Dec 2017 14:08:04 +0000 (15:08 +0100)]
x86/mm/dump_pagetables: Add page table directory to the debugfs VFS hierarchy
The upcoming support for dumping the kernel and the user space page tables
of the current process would create more random files in the top level
debugfs directory.
Add a page table directory and move the existing file to it.
Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Laight <David.Laight@aculab.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Eduardo Valentin <eduval@amazon.com> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Will Deacon <will.deacon@arm.com> Cc: aliguori@amazon.com Cc: daniel.gruss@iaik.tugraz.at Cc: hughd@google.com Cc: keescook@google.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Mon, 4 Dec 2017 14:08:03 +0000 (15:08 +0100)]
x86/mm/pti: Add Kconfig
Finally allow CONFIG_PAGE_TABLE_ISOLATION to be enabled.
PARAVIRT generally requires that the kernel not manage its own page tables.
It also means that the hypervisor and kernel must agree wholeheartedly
about what format the page tables are in and what they contain.
PAGE_TABLE_ISOLATION, unfortunately, changes the rules and they
can not be used together.
I've seen conflicting feedback from maintainers lately about whether they
want the Kconfig magic to go first or last in a patch series. It's going
last here because the partially-applied series leads to kernels that can
not boot in a bunch of cases. I did a run through the entire series with
CONFIG_PAGE_TABLE_ISOLATION=y to look for build errors, though.
[ tglx: Removed SMP and !PARAVIRT dependencies as they not longer exist ]
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: David Laight <David.Laight@aculab.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Eduardo Valentin <eduval@amazon.com> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Will Deacon <will.deacon@arm.com> Cc: aliguori@amazon.com Cc: daniel.gruss@iaik.tugraz.at Cc: hughd@google.com Cc: keescook@google.com Cc: linux-mm@kvack.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Vlastimil Babka [Tue, 19 Dec 2017 21:33:46 +0000 (22:33 +0100)]
x86/dumpstack: Indicate in Oops whether PTI is configured and enabled
CONFIG_PAGE_TABLE_ISOLATION is relatively new and intrusive feature that may
still have some corner cases which could take some time to manifest and be
fixed. It would be useful to have Oops messages indicate whether it was
enabled for building the kernel, and whether it was disabled during boot.
Example of fully enabled:
Oops: 0001 [#1] SMP PTI
Example of enabled during build, but disabled during boot:
Oops: 0001 [#1] SMP NOPTI
We can decide to remove this after the feature has been tested in the field
long enough.
[ tglx: Made it use boot_cpu_has() as requested by Borislav ]
Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Eduardo Valentin <eduval@amazon.com> Acked-by: Dave Hansen <dave.hansen@intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Andy Lutomirsky <luto@kernel.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Laight <David.Laight@aculab.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Will Deacon <will.deacon@arm.com> Cc: aliguori@amazon.com Cc: bpetkov@suse.de Cc: daniel.gruss@iaik.tugraz.at Cc: hughd@google.com Cc: jkosina@suse.cz Cc: keescook@google.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Mon, 4 Dec 2017 14:08:01 +0000 (15:08 +0100)]
x86/mm: Use INVPCID for __native_flush_tlb_single()
This uses INVPCID to shoot down individual lines of the user mapping
instead of marking the entire user map as invalid. This
could/might/possibly be faster.
This for sure needs tlb_single_page_flush_ceiling to be redetermined;
esp. since INVPCID is _slow_.
A detailed performance analysis is available here:
Peter Zijlstra [Mon, 4 Dec 2017 14:08:00 +0000 (15:08 +0100)]
x86/mm: Optimize RESTORE_CR3
Most NMI/paranoid exceptions will not in fact change pagetables and would
thus not require TLB flushing, however RESTORE_CR3 uses flushing CR3
writes.
Restores to kernel PCIDs can be NOFLUSH, because we explicitly flush the
kernel mappings and now that we track which user PCIDs need flushing we can
avoid those too when possible.
This does mean RESTORE_CR3 needs an additional scratch_reg, luckily both
sites have plenty available.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Laight <David.Laight@aculab.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Eduardo Valentin <eduval@amazon.com> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Will Deacon <will.deacon@arm.com> Cc: aliguori@amazon.com Cc: daniel.gruss@iaik.tugraz.at Cc: hughd@google.com Cc: keescook@google.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Peter Zijlstra [Mon, 4 Dec 2017 14:07:59 +0000 (15:07 +0100)]
x86/mm: Use/Fix PCID to optimize user/kernel switches
We can use PCID to retain the TLBs across CR3 switches; including those now
part of the user/kernel switch. This increases performance of kernel
entry/exit at the cost of more expensive/complicated TLB flushing.
Now that we have two address spaces, one for kernel and one for user space,
we need two PCIDs per mm. We use the top PCID bit to indicate a user PCID
(just like we use the PFN LSB for the PGD). Since we do TLB invalidation
from kernel space, the existing code will only invalidate the kernel PCID,
we augment that by marking the corresponding user PCID invalid, and upon
switching back to userspace, use a flushing CR3 write for the switch.
In order to access the user_pcid_flush_mask we use PER_CPU storage, which
means the previously established SWAPGS vs CR3 ordering is now mandatory
and required.
Having to do this memory access does require additional registers, most
sites have a functioning stack and we can spill one (RAX), sites without
functional stack need to otherwise provide the second scratch register.
Note: PCID is generally available on Intel Sandybridge and later CPUs.
Note: Up until this point TLB flushing was broken in this series.
Based-on-code-from: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Laight <David.Laight@aculab.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Eduardo Valentin <eduval@amazon.com> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Will Deacon <will.deacon@arm.com> Cc: aliguori@amazon.com Cc: daniel.gruss@iaik.tugraz.at Cc: hughd@google.com Cc: keescook@google.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Mon, 4 Dec 2017 14:07:57 +0000 (15:07 +0100)]
x86/mm: Allow flushing for future ASID switches
If changing the page tables in such a way that an invalidation of all
contexts (aka. PCIDs / ASIDs) is required, they can be actively invalidated
by:
1. INVPCID for each PCID (works for single pages too).
2. Load CR3 with each PCID without the NOFLUSH bit set
3. Load CR3 with the NOFLUSH bit set for each and do INVLPG for each address.
But, none of these are really feasible since there are ~6 ASIDs (12 with
PAGE_TABLE_ISOLATION) at the time that invalidation is required.
Instead of actively invalidating them, invalidate the *current* context and
also mark the cpu_tlbstate _quickly_ to indicate future invalidation to be
required.
At the next context-switch, look for this indicator
('invalidate_other' being set) invalidate all of the
cpu_tlbstate.ctxs[] entries.
This ensures that any future context switches will do a full flush
of the TLB, picking up the previous changes.
[ tglx: Folded more fixups from Peter ]
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: David Laight <David.Laight@aculab.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Eduardo Valentin <eduval@amazon.com> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Will Deacon <will.deacon@arm.com> Cc: aliguori@amazon.com Cc: daniel.gruss@iaik.tugraz.at Cc: hughd@google.com Cc: keescook@google.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
projects / mirror_ubuntu-bionic-kernel.git / log