The failure happens when allocating the spinlock array.
Even with GFP_KERNEL its unlikely for such a large allocation
to succeed.
Thomas Graf pointed me at inet_ehash_locks_alloc(), so in addition
to adding NOWARN for atomic allocations this also makes the bucket-array
sizing more conservative.
In commit 095dc8e0c3686 ("tcp: fix/cleanup inet_ehash_locks_alloc()"),
Eric Dumazet says: "Budget 2 cache lines per cpu worth of 'spinlocks'".
IOW, consider size needed by a single spinlock when determining
number of locks per cpu. So with 64 byte per cacheline and 4 byte per
spinlock this gives 32 locks per cpu.
Resulting size of the lock-array (sizeof(spinlock) == 4):
Reported-by: Sander Eikelenboom <linux@eikelenboom.it> Suggested-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Fri, 12 Aug 2016 14:10:33 +0000 (16:10 +0200)]
net: remove type_check from dev_get_nest_level()
The idea for type_check in dev_get_nest_level() was to count the number
of nested devices of the same type (currently, only macvlan or vlan
devices).
This prevented the false positive lockdep warning on configurations such
as:
eth0 <--- macvlan0 <--- vlan0 <--- macvlan1
However, this doesn't prevent a warning on a configuration such as:
In this case, all the locks end up with a nesting subclass of 1, so
lockdep thinks that there is still a deadlock:
- in the first case we have (macvlan_netdev_addr_lock_key, 1) and then
take (vlan_netdev_xmit_lock_key, 1)
- in the second case, we have (vlan_netdev_xmit_lock_key, 1) and then
take (macvlan_netdev_addr_lock_key, 1)
By removing the linktype check in dev_get_nest_level() and always
incrementing the nesting depth, lockdep considers this configuration
valid.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Manning [Fri, 12 Aug 2016 11:02:38 +0000 (12:02 +0100)]
net: ipv6: Do not keep IPv6 addresses when IPv6 is disabled
If IPv6 is disabled when the option is set to keep IPv6
addresses on link down, userspace is unaware of this as
there is no such indication via netlink. The solution is to
remove the IPv6 addresses in this case, which results in
netlink messages indicating removal of addresses in the
usual manner. This fix also makes the behavior consistent
with the case of having IPv6 disabled first, which stops
IPv6 addresses from being added.
Fixes: f1705ec197e7 ("net: ipv6: Make address flushing on ifdown optional") Signed-off-by: Mike Manning <mmanning@brocade.com> Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We should initialize sctp_ht_iter::start_fail to zero if ->start()
succeeds, otherwise it's possible that we leave an old value of 1 there,
which will cause ->stop() to not call sctp_transport_walk_stop(), which
causes all sorts of problems like not calling rcu_read_unlock() (and
preempt_enable()), eventually leading to more warnings like this:
BUG: sleeping function called from invalid context at mm/slab.h:388
in_atomic(): 0, irqs_disabled(): 0, pid: 16551, name: trinity-c2
Preemption disabled at:[<ffffffff819bceb6>] rhashtable_walk_start+0x46/0x150
Notice that this is a subtly different stacktrace from the one in commit 5fc382d875 ("net/sctp: terminate rhashtable walk correctly").
Cc: Xin Long <lucien.xin@gmail.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Acked-By: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If iriap_register_lsap() fails to allocate memory, self->lsap is
set to NULL. However, none of the callers handle the failure and
irlmp_connect_request() will happily dereference it:
There's more problems with missing error checks in iriap_init() (and
indeed all of irda_init()), but that's a bigger problem that needs
very careful review and testing. This patch will fix the most serious
bug (as it's easily reached from unprivileged userspace).
I have tested my patch with a reproducer.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Fri, 12 Aug 2016 05:48:21 +0000 (07:48 +0200)]
ipv6: suppress sparse warnings in IP6_ECN_set_ce()
Pass the correct type __wsum to csum_sub() and csum_add(). This doesn't
really change anything since __wsum really *is* __be32, but removes the
address space warnings from sparse.
Cc: Eric Dumazet <edumazet@google.com> Fixes: 34ae6a1aa054 ("ipv6: update skb->csum when CE mark is propagated") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 11 Aug 2016 19:38:37 +0000 (21:38 +0200)]
bpf: fix write helpers with regards to non-linear parts
Fix the bpf_try_make_writable() helper and all call sites we have in BPF,
it's currently defect with regards to skbs when the write_len spans into
non-linear parts, no matter if cloned or not.
There are multiple issues at once. First, using skb_store_bits() is not
correct since even if we have a cloned skb, page frags can still be shared.
To really make them private, we need to pull them in via __pskb_pull_tail()
first, which also gets us a private head via pskb_expand_head() implicitly.
This is for helpers like bpf_skb_store_bytes(), bpf_l3_csum_replace(),
bpf_l4_csum_replace(). Really, the only thing reasonable and working here
is to call skb_ensure_writable() before any write operation. Meaning, via
pskb_may_pull() it makes sure that parts we want to access are pulled in and
if not does so plus unclones the skb implicitly. If our write_len still fits
the headlen and we're cloned and our header of the clone is not writable,
then we need to make a private copy via pskb_expand_head(). skb_store_bits()
is a bit misleading and only safe to store into non-linear data in different
contexts such as 357b40a18b04 ("[IPV6]: IPV6_CHECKSUM socket option can
corrupt kernel memory").
For above BPF helper functions, it means after fixed bpf_try_make_writable(),
we've pulled in enough, so that we operate always based on skb->data. Thus,
the call to skb_header_pointer() and skb_store_bits() becomes superfluous.
In bpf_skb_store_bytes(), the len check is unnecessary too since it can
only pass in maximum of BPF stack size, so adding offset is guaranteed to
never overflow. Also bpf_l3/4_csum_replace() helpers must test for proper
offset alignment since they use __sum16 pointer for writing resulting csum.
The remaining helpers that change skb data not discussed here yet are
bpf_skb_vlan_push(), bpf_skb_vlan_pop() and bpf_skb_change_proto(). The
vlan helpers internally call either skb_ensure_writable() (pop case) and
skb_cow_head() (push case, for head expansion), respectively. Similarly,
bpf_skb_proto_xlat() takes care to not mangle page frags.
Fixes: 608cd71a9c7c ("tc: bpf: generalize pedit action") Fixes: 91bc4822c3d6 ("tc: bpf: add checksum helpers") Fixes: 3697649ff29e ("bpf: try harder on clones when writing into skb") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Thu, 11 Aug 2016 17:17:22 +0000 (18:17 +0100)]
calipso: fix resource leak on calipso_genopt failure
Currently, if calipso_genopt fails then the error exit path
does not free the ipv6_opt_hdr new causing a memory leak. Fix
this by kfree'ing new on the error exit path.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 12 Aug 2016 20:17:17 +0000 (22:17 +0200)]
bpf: fix bpf_skb_in_cgroup helper naming
While hashing out BPF's current_task_under_cgroup helper bits, it came
to discussion that the skb_in_cgroup helper name was suboptimally chosen.
Tejun says:
So, I think in_cgroup should mean that the object is in that
particular cgroup while under_cgroup in the subhierarchy of that
cgroup. Let's rename the other subhierarchy test to under too. I
think that'd be a lot less confusing going forward.
[...]
It's more intuitive and gives us the room to implement the real
"in" test if ever necessary in the future.
Since this touches uapi bits, we need to change this as long as v4.8
is not yet officially released. Thus, change the helper enum and rename
related bits.
Arnd Bergmann [Wed, 10 Aug 2016 21:54:08 +0000 (23:54 +0200)]
dsa: mv88e6xxx: hide unused functions
When CONFIG_NET_DSA_HWMON is disabled, we get warnings about two unused
functions whose only callers are all inside of an #ifdef:
drivers/net/dsa/mv88e6xxx.c:3257:12: 'mv88e6xxx_mdio_page_write' defined but not used [-Werror=unused-function]
drivers/net/dsa/mv88e6xxx.c:3244:12: 'mv88e6xxx_mdio_page_read' defined but not used [-Werror=unused-function]
This adds another ifdef around the function definitions. The warnings
appeared after the functions were marked 'static', but the problem
was already there before that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 57d3231057e9 ("net: dsa: mv88e6xxx: fix style issues") Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Thu, 11 Aug 2016 13:24:27 +0000 (15:24 +0200)]
macsec: use after free when deleting the underlying device
macsec_notify() loops over the list of macsec devices configured on the
underlying device when this device is being removed. This list is part
of the rx_handler data.
However, macsec_dellink unregisters the rx_handler and frees the
rx_handler data when the last macsec device is removed from the
underlying device.
Add macsec_common_dellink() to delete macsec devices without
unregistering the rx_handler and freeing the associated data.
Fixes: 960d5848dbf1 ("macsec: fix memory leaks around rx_handler (un)registration") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Thu, 11 Aug 2016 10:15:56 +0000 (18:15 +0800)]
macvtap: fix use after free for skb_array during release
We've clean skb_array in macvtap_put_queue() but still try to pop from
it during macvtap_sock_destruct(). Fix this use after free by moving
the skb array cleanup to macvtap_sock_destruct() instead.
Fixes: 362899b8725b ("macvtap: switch to use skb array") Reported-by: Cornelia Huck <cornelia.huck@de.ibm.com> Tested-by: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
openvswitch: do not ignore netdev errors when creating tunnel vports
The creation of a tunnel vport (geneve, gre, vxlan) brings up a
corresponding netdev, a multi-step operation which can fail.
For example, changing a vxlan vport's netdev state to 'up' binds the
vport's socket to a UDP port - if the binding fails (e.g. due to the
port being in use), the error is currently ignored giving the
appearance that the tunnel vport creation completed successfully.
Signed-off-by: Martynas Pumputis <martynas@weave.works> Acked-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
In commit cf6f7e1d5109 ("tipc: dump monitor attributes"),
I dereferenced a pointer before checking if its valid.
This is reported by static check Smatch as:
net/tipc/monitor.c:733 tipc_nl_add_monitor_peer()
warn: variable dereferenced before check 'mon' (see line 731)
In this commit, we check for a valid monitor before proceeding
with any other operation.
Fixes: cf6f7e1d5109 ("tipc: dump monitor attributes") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Toshiaki Makita [Thu, 4 Aug 2016 02:11:19 +0000 (11:11 +0900)]
bridge: Fix problems around fdb entries pointing to the bridge device
Adding fdb entries pointing to the bridge device uses fdb_insert(),
which lacks various checks and does not respect added_by_user flag.
As a result, some inconsistent behavior can happen:
* Adding temporary entries succeeds but results in permanent entries.
* Same goes for "dynamic" and "use".
* Changing mac address of the bridge device causes deletion of
user-added entries.
* Replacing existing entries looks successful from userspace but actually
not, regardless of NLM_F_EXCL flag.
Use the same logic as other entries and fix them.
Fixes: 3741873b4f73 ("bridge: allow adding of fdb entries pointing to the bridge device") Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wenyou Yang [Fri, 5 Aug 2016 06:35:41 +0000 (14:35 +0800)]
net: phy: micrel: Add specific suspend
Disable all interrupts when suspend, they will be enabled
when resume. Otherwise, the suspend/resume process will be
blocked occasionally.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dm9000: Fix irq trigger type setup on non-dt platforms
Commit b5a099c67a1c36b "net: ethernet: davicom: fix devicetree irq
resource" causes an interrupt storm after the ethernet interface
is activated on S3C24XX platform (ARM non-dt), due to the interrupt
trigger type not being set properly.
It seems, after adding parsing of IRQ flags in commit 7085a7401ba54e92b
"drivers: platform: parse IRQ flags from resources", there is no path
for non-dt platforms where irq_set_type callback could be invoked when
we don't pass the trigger type flags to the request_irq() call.
In case of a board where the regression is seen the interrupt trigger
type flags are passed through a platform device's resource and it is
not currently handled properly without passing the irq trigger type
flags to the request_irq() call. In case of OF an of_irq_get() call
within platform_get_irq() function seems to be ensuring required irq_chip
setup, but there is no equivalent code for non OF/ACPI platforms.
This patch mostly restores irq trigger type setting code which has been
removed in commit ("net: ethernet: davicom: fix devicetree irq resource").
Fixes: b5a099c67a1c36b913 ("net: ethernet: davicom: fix devicetree irq resource") Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers: net: cpsw: fix kmemleak false-positive reports for sk buffers
Kmemleak reports following false positive memory leaks for each sk
buffers allocated by CPSW (__netdev_alloc_skb_ip_align()) in
cpsw_ndo_open() and cpsw_rx_handler():
This happens because CPSW allocates SK buffers and then passes
pointers on them in CPDMA where they stored in internal CPPI RAM
(SRAM) which belongs to DEV MMIO space. Kmemleak does not scan IO
memory and so reports memory leaks.
Hence, mark allocated sk buffers as false positive explicitly.
Cc: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vti: flush x-netns xfrm cache when vti interface is removed
When executing the script included below, the netns delete operation
hangs with the following message (repeated at 10 second intervals):
kernel:unregister_netdevice: waiting for lo to become free. Usage count = 1
This occurs because a reference to the lo interface in the "secure" netns
is still held by a dst entry in the xfrm bundle cache in the init netns.
Address this problem by garbage collecting the tunnel netns flow cache
when a cross-namespace vti interface receives a NETDEV_DOWN notification.
A more detailed description of the problem scenario (referencing commands
in the script below):
(1) ip link add vti_test type vti local 1.1.1.1 remote 1.1.1.2 key 1
The vti_test interface is created in the init namespace. vti_tunnel_init()
attaches a struct ip_tunnel to the vti interface's netdev_priv(dev),
setting the tunnel net to &init_net.
(2) ip link set vti_test netns secure
The vti_test interface is moved to the "secure" netns. Note that
the associated struct ip_tunnel still has tunnel->net set to &init_net.
Note that tunnel->net is the init namespace, while skb_dst(skb) references
the vti_test interface in the "secure" namespace. The returned dst
references an interface in the init namespace.
Also note that the first parameter to xfrm_lookup() determines which flow
cache is used to store the computed xfrm bundle, so after xfrm_lookup()
returns there will be a cached bundle in the init namespace flow cache
with a dst referencing a device in the "secure" namespace.
(4) ip netns del secure
Kernel begins to delete the "secure" namespace. At some point the
vti_test interface is deleted, at which point dst_ifdown() changes
the dst->dev in the cached xfrm bundle flow from vti_test to lo (still
in the "secure" namespace however).
Since nothing has happened to cause the init namespace's flow cache
to be garbage collected, this dst remains attached to the flow cache,
so the kernel loops waiting for the last reference to lo to go away.
<Begin script>
ip link add br1 type bridge
ip link set dev br1 up
ip addr add dev br1 1.1.1.1/8
ip netns add secure
ip link add vti_test type vti local 1.1.1.1 remote 1.1.1.2 key 1
ip link set vti_test netns secure
ip netns exec secure ip link set vti_test up
ip netns exec secure ip link s lo up
ip netns exec secure ip addr add dev lo 192.168.100.1/24
ip netns exec secure ip route add 192.168.200.0/24 dev vti_test
ip xfrm policy flush
ip xfrm state flush
ip xfrm policy add dir out tmpl src 1.1.1.1 dst 1.1.1.2 \
proto esp mode tunnel mark 1
ip xfrm policy add dir in tmpl src 1.1.1.2 dst 1.1.1.1 \
proto esp mode tunnel mark 1
ip xfrm state add src 1.1.1.1 dst 1.1.1.2 proto esp spi 1 \
mode tunnel enc des3_ede 0x112233445566778811223344556677881122334455667788
ip xfrm state add src 1.1.1.2 dst 1.1.1.1 proto esp spi 1 \
mode tunnel enc des3_ede 0x112233445566778811223344556677881122334455667788
Reported-by: Hangbin Liu <haliu@redhat.com> Reported-by: Jan Tluka <jtluka@redhat.com> Signed-off-by: Lance Richardson <lrichard@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Tue, 9 Aug 2016 10:30:43 +0000 (11:30 +0100)]
rxrpc: Fix a use-after-push in data_ready handler
Fix a use of a packet after it has been enqueued onto the packet processing
queue in the data_ready handler. Once on a call's Rx queue, we mustn't
touch it any more as it may be dequeued and freed by the call processor
running on a work queue.
Save the values we need before enqueuing.
Without this, we can get an oops like the following:
David Howells [Tue, 9 Aug 2016 09:11:48 +0000 (10:11 +0100)]
rxrpc: Once packet posted in data_ready, don't retry posting
Once a packet has been posted to a connection in the data_ready handler, we
mustn't try reposting if we then find that the connection is dying as the
refcount has been given over to the dying connection and the packet might
no longer exist.
Losing the packet isn't a problem as the peer will retransmit.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 8 Aug 2016 09:27:26 +0000 (10:27 +0100)]
rxrpc: Don't access connection from call if pointer is NULL
The call state machine processor sets up the message parameters for a UDP
message that it might need to transmit in advance on the basis that there's
a very good chance it's going to have to transmit either an ACK or an
ABORT. This requires it to look in the connection struct to retrieve some
of the parameters.
However, if the call is complete, the call connection pointer may be NULL
to dissuade the processor from transmitting a message. However, there are
some situations where the processor is still going to be called - and it's
still going to set up message parameters whether it needs them or not.
This results in a NULL pointer dereference at:
net/rxrpc/call_event.c:837
To fix this, skip the message pre-initialisation if there's no connection
attached.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 8 Aug 2016 12:06:41 +0000 (13:06 +0100)]
rxrpc: Need to flag call as being released on connect failure
If rxrpc_new_client_call() fails to make a connection, the call record that
it allocated needs to be marked as RXRPC_CALL_RELEASED before it is passed
to rxrpc_put_call() to indicate that it no longer has any attachment to the
AF_RXRPC socket.
Without this, an assertion failure may occur at:
net/rxrpc/call_object:635
Signed-off-by: David Howells <dhowells@redhat.com>
Arnd Bergmann [Mon, 8 Aug 2016 10:13:45 +0000 (12:13 +0200)]
rxrpc: fix uninitialized pointer dereference in debug code
A newly added bugfix caused an uninitialized variable to be
used for printing debug output. This is harmless as long
as the debug setting is disabled, but otherwise leads to an
immediate crash.
gcc warns about this when -Wmaybe-uninitialized is enabled:
net/rxrpc/call_object.c: In function 'rxrpc_release_call':
net/rxrpc/call_object.c:496:163: error: 'sp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The initialization was removed but one of the users remains.
This adds back the initialization.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 372ee16386bb ("rxrpc: Fix races between skb free, ACK generation and replying") Signed-off-by: David Howells <dhowells@redhat.com>
Liping Zhang [Mon, 8 Aug 2016 14:10:26 +0000 (22:10 +0800)]
netfilter: ctnetlink: reject new conntrack request with different l4proto
Currently, user can add a conntrack with different l4proto via nfnetlink.
For example, original tuple is TCP while reply tuple is SCTP. This is
invalid combination, we should report EINVAL to userspace.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Liping Zhang [Mon, 8 Aug 2016 14:07:27 +0000 (22:07 +0800)]
netfilter: nfnetlink_queue: reject verdict request from different portid
Like NFQNL_MSG_VERDICT_BATCH do, we should also reject the verdict
request when the portid is not same with the initial portid(maybe
from another process).
Liping Zhang [Mon, 8 Aug 2016 14:03:40 +0000 (22:03 +0800)]
netfilter: nfnetlink_queue: fix memory leak when attach expectation successfully
User can use NFQA_EXP to attach expectations to conntracks, but we
forget to put back nf_conntrack_expect when it is inserted successfully,
i.e. in this normal case, expect's use refcnt will be 3. So even we
unlink it and put it back later, the use refcnt is still 1, then the
memory will be leaked forever.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Liping Zhang [Mon, 8 Aug 2016 13:57:58 +0000 (21:57 +0800)]
netfilter: nf_ct_expect: remove the redundant slash when policy name is empty
The 'name' filed in struct nf_conntrack_expect_policy{} is not a
pointer, so check it is NULL or not will always return true. Even if the
name is empty, slash will always be displayed like follows:
# cat /proc/net/nf_conntrack_expect
297 l3proto = 2 proto=6 src=1.1.1.1 dst=2.2.2.2 sport=1 dport=1025 ftp/
^
Fixes: 3a8fc53a45c4 ("netfilter: nf_ct_helper: allocate 16 bytes for the helper and policy names") Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
qed: Update app count when adding a new dcbx app entry to the table.
App count is not updated while adding new app entry to the dcbx app table.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qed: Add dcbx app support for IEEE Selection Field.
MFW now supports the Selection field for IEEE mode. Add driver changes to
use the newer MFW masks to read/write the port-id value.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qed: Use ieee mfw-mask to get ethtype in ieee-dcbx mode.
Ethtype value is being read incorrectly in ieee-dcbx mode. Use the
correct mfw mask value.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qed: Remove the endian-ness conversion for pri_to_tc value.
Endian-ness conversion is not needed for priority-to-TC field as the
field is already being read/written by the driver in big-endian way.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 7 Aug 2016 06:15:13 +0000 (14:15 +0800)]
sctp: use event->chunk when it's valid
Commit 52253db924d1 ("sctp: also point GSO head_skb to the sk when
it's available") used event->chunk->head_skb to get the head_skb in
sctp_ulpevent_set_owner().
But at that moment, the event->chunk was NULL, as it cloned the skb
in sctp_ulpevent_make_rcvmsg(). Therefore, that patch didn't really
work.
This patch is to move the event->chunk initialization before calling
sctp_ulpevent_receive_data() so that it uses event->chunk when it's
valid.
Fixes: 52253db924d1 ("sctp: also point GSO head_skb to the sk when it's available") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pravin shelar [Sat, 6 Aug 2016 00:45:37 +0000 (17:45 -0700)]
net: vxlan: lwt: Fix vxlan local traffic.
vxlan driver has bypass for local vxlan traffic, but that
depends on information about all VNIs on local system in
vxlan driver. This is not available in case of LWT.
Therefore following patch disable encap bypass for LWT
vxlan traffic.
Fixes: ee122c79d42 ("vxlan: Flow based tunneling"). Reported-by: Jakub Libosvar <jlibosva@redhat.com> Signed-off-by: Pravin B Shelar <pshelar@ovn.org> Acked-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pravin shelar [Sat, 6 Aug 2016 00:45:36 +0000 (17:45 -0700)]
net: vxlan: lwt: Use source ip address during route lookup.
LWT user can specify destination as well as source ip address
for given tunnel endpoint. But vxlan is ignoring given source
ip address. Following patch uses both ip address to route the
tunnel packet. This consistent with other LWT implementations,
like GENEVE and GRE.
Fixes: ee122c79d42 ("vxlan: Flow based tunneling"). Signed-off-by: Pravin B Shelar <pshelar@ovn.org> Acked-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 4 Aug 2016 22:11:13 +0000 (00:11 +0200)]
bpf: fix checksum for vlan push/pop helper
When having skbs on ingress with CHECKSUM_COMPLETE, tc BPF programs don't
push rcsum of mac header back in and after BPF run back pull out again as
opposed to some other subsystems (ovs, for example).
For cases like q-in-q, meaning when a vlan tag for offloading is already
present and we're about to push another one, then skb_vlan_push() pushes the
inner one into the skb, increasing mac header and skb_postpush_rcsum()'ing
the 4 bytes vlan header diff. Likewise, for the reverse operation in
skb_vlan_pop() for the case where vlan header needs to be pulled out of the
skb, we're decreasing the mac header and skb_postpull_rcsum()'ing the 4 bytes
rcsum of the vlan header that was removed.
However mangling the rcsum here will lead to hw csum failure for BPF case,
since we're pulling or pushing data that was not part of the current rcsum.
Changing tc BPF programs in general to push/pull rcsum around BPF_PROG_RUN()
is also not really an option since current behaviour is ABI by now, but apart
from that would also mean to do quite a bit of useless work in the sense that
usually 12 bytes need to be rcsum pushed/pulled also when we don't need to
touch this vlan related corner case. One way to fix it would be to push the
necessary rcsum fixup down into vlan helpers that are (mostly) slow-path
anyway.
Fixes: 4e10df9a60d9 ("bpf: introduce bpf_skb_vlan_push/pop() helpers") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 4 Aug 2016 22:11:12 +0000 (00:11 +0200)]
bpf: fix checksum fixups on bpf_skb_store_bytes
bpf_skb_store_bytes() invocations above L2 header need BPF_F_RECOMPUTE_CSUM
flag for updates, so that CHECKSUM_COMPLETE will be fixed up along the way.
Where we ran into an issue with bpf_skb_store_bytes() is when we did a
single-byte update on the IPv6 hoplimit despite using BPF_F_RECOMPUTE_CSUM
flag; simple ping via ICMPv6 triggered a hw csum failure as a result. The
underlying issue has been tracked down to a buffer alignment issue.
Meaning, that csum_partial() computations via skb_postpull_rcsum() and
skb_postpush_rcsum() pair invoked had a wrong result since they operated on
an odd address for the hoplimit, while other computations were done on an
even address. This mix doesn't work as-is with skb_postpull_rcsum(),
skb_postpush_rcsum() pair as it always expects at least half-word alignment
of input buffers, which is normally the case. Thus, instead of these helpers
using csum_sub() and (implicitly) csum_add(), we need to use csum_block_sub(),
csum_block_add(), respectively. For unaligned offsets, they rotate the sum
to align it to a half-word boundary again, otherwise they work the same as
csum_sub() and csum_add().
Adding __skb_postpull_rcsum(), __skb_postpush_rcsum() variants that take the
offset as an input and adapting bpf_skb_store_bytes() to them fixes the hw
csum failures again. The skb_postpull_rcsum(), skb_postpush_rcsum() helpers
use a 0 constant for offset so that the compiler optimizes the offset & 1
test away and generates the same code as with csum_sub()/_add().
Fixes: 608cd71a9c7c ("tc: bpf: generalize pedit action") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 4 Aug 2016 22:11:11 +0000 (00:11 +0200)]
bpf: also call skb_postpush_rcsum on xmit occasions
Follow-up to commit f8ffad69c9f8 ("bpf: add skb_postpush_rcsum and fix
dev_forward_skb occasions") to fix an issue for dev_queue_xmit() redirect
locations which need CHECKSUM_COMPLETE fixups on ingress.
For the same reasons as described in f8ffad69c9f8 already, we of course
also need this here, since dev_queue_xmit() on a veth device will let us
end up in the dev_forward_skb() helper again to cross namespaces.
Latter then calls into skb_postpull_rcsum() to pull out L2 header, so
that netif_rx_internal() sees CHECKSUM_COMPLETE as it is expected. That
is, CHECKSUM_COMPLETE on ingress covering L2 _payload_, not L2 headers.
Also here we have to address bpf_redirect() and bpf_clone_redirect().
Fixes: 3896d655f4d4 ("bpf: introduce bpf_clone_redirect() helper") Fixes: 27b29f63058d ("bpf: add bpf_redirect() helper") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
...leading to the following warning for !DEBUG builds:
drivers/net/ethernet/tundra/tsi108_eth.c:169:13: warning: 'dump_eth_one' defined but not used [-Wunused-function]
static void dump_eth_one(struct net_device *dev)
^
...when using the arch/powerpc/configs/mpc7448_hpc2_defconfig
Put the function definition under the same #ifdef as the call site
to avoid the warning.
Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 4 Aug 2016 14:36:22 +0000 (17:36 +0300)]
mlxsw: spectrum: Add missing DCB rollback in error path
We correctly execute mlxsw_sp_port_dcb_fini() when port is removed, but
I missed its rollback in the error path of port creation, so add it.
Fixes: f00817df2b42 ("mlxsw: spectrum: Introduce support for Data Center Bridging (DCB)") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 4 Aug 2016 14:36:21 +0000 (17:36 +0300)]
mlxsw: spectrum: Do not override PAUSE settings
The PFCC register is used to configure both PAUSE and PFC frames.
Therefore, when PFC frames are disabled we must make sure we don't
mistakenly also disable PAUSE frames (which might be enabled).
Fix this by packing the PFCC register with the current PAUSE settings.
Note that this register is also accessed via ethtool ops, but there we
are guaranteed to have PFC disabled.
Fixes: d81a6bdb87ce ("mlxsw: spectrum: Add IEEE 802.1Qbb PFC support") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 1aa661f5c3df1 ("rhashtable-test: Measure time to insert, remove & traverse entries") Signed-off-by: Phil Sutter <phil@nwl.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Sutter [Thu, 4 Aug 2016 10:11:57 +0000 (12:11 +0200)]
sctp_diag: Respect ss adding TCPF_CLOSE to idiag_states
Since 'ss' always adds TCPF_CLOSE to idiag_states flags, sctp_diag can't
rely upon TCPF_LISTEN flag solely being present when listening sockets
are requested.
Signed-off-by: Phil Sutter <phil@nwl.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Sutter [Thu, 4 Aug 2016 10:11:56 +0000 (12:11 +0200)]
sctp_diag: Fix T3_rtx timer export
The asoc's timer value is not kept in asoc->timeouts array but in it's
primary transport instead.
Furthermore, we must export the timer only if it is pending, otherwise
the value will underrun when stored in an unsigned variable and
user space will only see a very large timeout value.
Signed-off-by: Phil Sutter <phil@nwl.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: nf_conntrack_sip: CSeq 0 is a valid CSeq
Do not drop packet when CSeq is 0 as 0 is also a valid value for CSeq.
simple_strtoul() will return 0 either when all digits are 0
or if there are no digits at all. Therefore when simple_strtoul()
returns 0 we check if first character is digit 0 or not.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nft_rbtree: ignore inactive matching element with no descendants
If we find a matching element that is inactive with no descendants, we
jump to the found label, then crash because of nul-dereference on the
left branch.
Fix this by checking that the element is active and not an interval end
and skipping the logic that only applies to the tree iteration.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Tested-by: Anders K. Pedersen <akp@akp.dk>
netfilter: nf_ct_h323: do not re-activate already expired timer
Commit 96d1327ac2e3 ("netfilter: h323: Use mod_timer instead of
set_expect_timeout") just simplify the source codes
if (!del_timer(&exp->timeout))
return 0;
add_timer(&exp->timeout);
to mod_timer(&exp->timeout, jiffies + info->timeout * HZ);
This is not correct, and introduce a race codition:
CPU0 CPU1
- timer expire
process_rcf expectation_timed_out
lock(exp_lock) -
find_exp waiting exp_lock...
re-activate timer!! waiting exp_lock...
unlock(exp_lock) lock(exp_lock)
- unlink expect
- free(expect)
- unlock(exp_lock)
So when the timer expires again, we will access the memory that
was already freed.
Replace mod_timer with mod_timer_pending here to fix this problem.
Fixes: 96d1327ac2e3 ("netfilter: h323: Use mod_timer instead of set_expect_timeout") Cc: Gao Feng <fgao@ikuai8.com> Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
David S. Miller [Sun, 7 Aug 2016 00:52:00 +0000 (20:52 -0400)]
Merge tag 'mac80211-for-davem-2016-08-05' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
First set of fixes for the current cycle:
* fix 80+80 bandwidth warning
* fix powersave with mac80211 TXQ implementation
* use correct way to free SKBs from multicast buffering
* mesh: fix operation ordering to work with all drivers
* mesh: end service period even when peer goes away
* mesh: correct HT opmode validity checks
* pass hw pointer from mac80211 to driver in TPT method,
fixing a bug (in a bit the wrong way, but that's what
we have right now)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The introduction of pre-allocated hash elements inadvertently broke
the behavior of bpf hash maps where users expected to call
bpf_map_update_elem() without considering that the map can be full.
Some programs do:
old_value = bpf_map_lookup_elem(map, key);
if (old_value) {
... prepare new_value on stack ...
bpf_map_update_elem(map, key, new_value);
}
Before pre-alloc the update() for existing element would work even
in 'map full' condition. Restore this behavior.
The above program could have updated old_value in place instead of
update() which would be faster and most programs use that approach,
but sometimes the values are large and the programs use update()
helper to do atomic replacement of the element.
Note we cannot simply update element's value in-place like percpu
hash map does and have to allocate extra num_possible_cpu elements
and use this extra reserve when the map is full.
Fixes: 6c9059817432 ("bpf: pre-allocate hash map elements") Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: b53: Add missing ULL suffix for 64-bit constant
On 32-bit (e.g. with m68k-linux-gnu-gcc-4.1):
drivers/net/dsa/b53/b53_common.c: In function ‘b53_arl_read’:
drivers/net/dsa/b53/b53_common.c:1072: warning: integer constant is too large for ‘long’ type
Fixes: 1da6df85c6fbed8f ("net: dsa: b53: Implement ARL add/del/dump operations") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Forster <dforster@brocade.com> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Wed, 3 Aug 2016 13:11:40 +0000 (14:11 +0100)]
rxrpc: Fix races between skb free, ACK generation and replying
Inside the kafs filesystem it is possible to occasionally have a call
processed and terminated before we've had a chance to check whether we need
to clean up the rx queue for that call because afs_send_simple_reply() ends
the call when it is done, but this is done in a workqueue item that might
happen to run to completion before afs_deliver_to_call() completes.
Further, it is possible for rxrpc_kernel_send_data() to be called to send a
reply before the last request-phase data skb is released. The rxrpc skb
destructor is where the ACK processing is done and the call state is
advanced upon release of the last skb. ACK generation is also deferred to
a work item because it's possible that the skb destructor is not called in
a context where kernel_sendmsg() can be invoked.
To this end, the following changes are made:
(1) kernel_rxrpc_data_consumed() is added. This should be called whenever
an skb is emptied so as to crank the ACK and call states. This does
not release the skb, however. kernel_rxrpc_free_skb() must now be
called to achieve that. These together replace
rxrpc_kernel_data_delivered().
(2) kernel_rxrpc_data_consumed() is wrapped by afs_data_consumed().
This makes afs_deliver_to_call() easier to work as the skb can simply
be discarded unconditionally here without trying to work out what the
return value of the ->deliver() function means.
The ->deliver() functions can, via afs_data_complete(),
afs_transfer_reply() and afs_extract_data() mark that an skb has been
consumed (thereby cranking the state) without the need to
conditionally free the skb to make sure the state is correct on an
incoming call for when the call processor tries to send the reply.
(3) rxrpc_recvmsg() now has to call kernel_rxrpc_data_consumed() when it
has finished with a packet and MSG_PEEK isn't set.
(4) rxrpc_packet_destructor() no longer calls rxrpc_hard_ACK_data().
Because of this, we no longer need to clear the destructor and put the
call before we free the skb in cases where we don't want the ACK/call
state to be cranked.
(5) The ->deliver() call-type callbacks are made to return -EAGAIN rather
than 0 if they expect more data (afs_extract_data() returns -EAGAIN to
the delivery function already), and the caller is now responsible for
producing an abort if that was the last packet.
(6) There are many bits of unmarshalling code where:
ret = afs_extract_data(call, skb, last, ...);
switch (ret) {
case 0: break;
case -EAGAIN: return 0;
default: return ret;
}
is to be found. As -EAGAIN can now be passed back to the caller, we
now just return if ret < 0:
ret = afs_extract_data(call, skb, last, ...);
if (ret < 0)
return ret;
(7) Checks for trailing data and empty final data packets has been
consolidated as afs_data_complete(). So:
if (skb->len > 0)
return -EBADMSG;
if (!last)
return 0;
becomes:
ret = afs_data_complete(call, skb, last);
if (ret < 0)
return ret;
(8) afs_transfer_reply() now checks the amount of data it has against the
amount of data desired and the amount of data in the skb and returns
an error to induce an abort if we don't get exactly what we want.
Without these changes, the following oops can occasionally be observed,
particularly if some printks are inserted into the delivery path:
This doesn't have an immediate effect, but can mess up later
LL_RESERVED_SPACE calculations, such as done in
net/ipv6/mcast.c:mld_newpack. For reference, this issue was found
from a skb_panic raised there after the length calculations had given
the wrong result.
Note the other current users of this interface
(drivers/net/tun.c:tun_set_headroom and
drivers/net/veth.c:veth_set_rx_headroom) are both checking this
correctly thus need no modification.
Thanks to Ben for some pointers from the crash dumps!
Cc: Benjamin Poirier <bpoirier@suse.com> Cc: Paolo Abeni <pabeni@redhat.com>
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1361414 Signed-off-by: Ian Wienand <iwienand@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maxim Altshul [Thu, 4 Aug 2016 12:43:04 +0000 (15:43 +0300)]
mac80211: Add ieee80211_hw pointer to get_expected_throughput
The variable is added to allow the driver an easy access to
it's own hw->priv when the op is invoked.
This fixes a crash in wlcore because it was relying on a
station pointer that wasn't initialized yet. It's the wrong
way to fix the crash, but it solves the problem for now and
it does make sense to have the hw pointer here.
Masashi Honma [Tue, 2 Aug 2016 08:16:57 +0000 (17:16 +0900)]
mac80211: End the MPSP even if EOSP frame was not acked
If QoS frame with EOSP (end of service period) subfield=1 sent by local
peer was not acked by remote peer, local peer did not end the MPSP. This
prevents local peer from going to DOZE state. And if the remote peer
goes away without closing connection, local peer continues AWAKE state
and wastes battery.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Tue, 2 Aug 2016 09:13:41 +0000 (11:13 +0200)]
mac80211: fix purging multicast PS buffer queue
The code currently assumes that buffered multicast PS frames don't have
a pending ACK frame for tx status reporting.
However, hostapd sends a broadcast deauth frame on teardown for which tx
status is requested. This can lead to the "Have pending ack frames"
warning on module reload.
Fix this by using ieee80211_free_txskb/ieee80211_purge_tx_queue.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Manish Chopra [Wed, 3 Aug 2016 08:02:02 +0000 (04:02 -0400)]
qlcnic: fix data structure corruption in async mbx command handling
This patch fixes a data structure corruption bug in the SRIOV VF mailbox
handler code. While handling mailbox commands from the atomic context,
driver is accessing and updating qlcnic_async_work_list_struct entry fields
in the async work list. These fields could be concurrently accessed by the
work function resulting in data corruption.
This patch restructures async mbx command handling by using a separate
async command list instead of using a list of work_struct structures.
A single work_struct is used to schedule and handle the async commands
with proper locking mechanism.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Sony Chacko <sony.chacko@qlogic.com> Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tg3: Report the correct number of RSS queues through tg3_get_rxnfc
This patch remove the wrong substraction from info->data in
tg3_get_rxnfc function. Without this patch, the number of RSS
queues reported is less by one.
Reported-by: Michal Soltys <soltys@ziu.info> Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When the rx coalescing time is 0, interrupts
are not generated from the controller and rx path hangs.
To avoid this rx hang, updating the driver to not allow
rx coalescing time to be 0.
Signed-off-by: Satish Baddipadige <satish.baddipadige@broadcom.com> Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We need to get a UNKNOWN_VALUE with imm to force id
generation so lines 0-5 make r7 a valid packet pointer.
We then read two different bytes from the packet and
add them to copies of the constructed packet pointer.
r8 (line 9) and r9 (line 11) will get the same id of 1,
independently. When either of them is validated (line
13) - find_good_pkt_pointers() will also mark the other
as safe. This leads to access on line 14 being mistakenly
considered safe.
Fixes: 969bf05eb3ce ("bpf: direct packet access") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Tue, 2 Aug 2016 10:23:29 +0000 (12:23 +0200)]
net: xgene: fix maybe-uninitialized variable
Building with -Wmaybe-uninitialized shows a potential use of
an uninitialized variable:
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c: In function 'xgene_enet_phy_connect':
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c:802:23: warning: 'phy_dev' may be used uninitialized in this function [-Wmaybe-uninitialized]
Although the compiler correctly identified this based on the function,
the current code is still safe as long dev->of_node is non-NULL
for the case of CONFIG_ACPI=n, which is currently the case.
The warning is now disabled by default, but still appears when
building with W=1, and other build test tools should be able to
detect it as well. Adding an #else clause here makes the code
more robust and makes it clear to the compiler that this cannot
happen.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 8089a96f601b ("drivers: net: xgene: Add backward compatibility") Signed-off-by: David S. Miller <davem@davemloft.net>
Jarno Rajahalme [Tue, 2 Aug 2016 02:36:07 +0000 (19:36 -0700)]
openvswitch: Remove incorrect WARN_ONCE().
ovs_ct_find_existing() issues a warning if an existing conntrack entry
classified as IP_CT_NEW is found, with the premise that this should
not happen. However, a newly confirmed, non-expected conntrack entry
remains IP_CT_NEW as long as no reply direction traffic is seen. This
has resulted into somewhat confusing kernel log messages. This patch
removes this check and warning.
Fixes: 289f2253 ("openvswitch: Find existing conntrack entry after upcall.") Suggested-by: Joe Stringer <joe@ovn.org> Signed-off-by: Jarno Rajahalme <jarno@ovn.org> Acked-by: Joe Stringer <joe@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 3 Aug 2016 16:50:06 +0000 (12:50 -0400)]
Merge tag 'trace-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"A few updates and fixes:
- move the suppressing of the __builtin_return_address >0 warning to
the tracing directory only.
- metag recordmcount fix for newer glibc's
- two tracing histogram fixes that were reported by KASAN"
* tag 'trace-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix use-after-free in hist_register_trigger()
tracing: Fix use-after-free in hist_unreg_all/hist_enable_unreg_all
Makefile: Mute warning for __builtin_return_address(>0) for tracing only
ftrace/recordmcount: Work around for addition of metag magic but not relocations
mac80211: mesh: flush stations before beacons are stopped
Some drivers (e.g. wl18xx) expect that the last stage in the
de-initialization process will be stopping the beacons, similar to AP flow.
Update ieee80211_stop_mesh() flow accordingly.
As peers can be removed dynamically, this would not impact other drivers.
Linus Torvalds [Tue, 2 Aug 2016 23:47:06 +0000 (19:47 -0400)]
Merge tag 'for-linus-v4.8' of git://github.com/martinbrandenburg/linux
Pull orangefs update from Martin Brandenburg:
"Kernel side caching and executable bugfix
This allows OrangeFS to utilize the dcache and adds an in kernel
attribute cache. We previously used the user side client for this
purpose.
We see a modest performance increase on small file operations. For
example, without the cache, compiling coreutils takes about 17
minutes. With the patch and a 50 millisecond timeout for
dcache_timeout_msecs and getattr_timeout_msecs (the default),
compiling coreutils takes about 6 minutes 20 seconds. On the same
hardware, compiling coreutils on an xfs filesystem takes 90 seconds.
We see similar improvements with mdtest and a test involving writing,
reading, and deleting a large number of small files.
Interested parties can review more data at the following URL.
The eventual goal of this is to allow getdents to turn into a
readdirplus to the OrangeFS server. The cache will be filled then,
which should provide a performance benefit to the common case of
readdir followed by getattr on each entry (i.e. ls -l).
This also fixes a bug. When orangefs_inode_permission was added, it
did not collect i_size from the OrangeFS server, since this presses an
unnecessary load on the OrangeFS server. However, it left a case
where i_size is never initialized. Then running an executable could
fail.
With this patch, size is always collected to be inserted into the
cache. Thus the bug disappears. If this patch is not accepted during
this merge window, we will send a one-line band-aid for this bug
instead"
* tag 'for-linus-v4.8' of git://github.com/martinbrandenburg/linux:
Orangefs: update orangefs.txt
orangefs: Account for jiffies wraparound.
orangefs: Change default dcache and getattr timeout to 50 msec.
orangefs: Allow dcache and getattr cache time to be configured.
orangefs: Cache getattr results.
orangefs: Use d_time to avoid excessive lookups
Linus Torvalds [Tue, 2 Aug 2016 23:39:09 +0000 (19:39 -0400)]
Merge tag 'ceph-for-4.8-rc1' of git://github.com/ceph/ceph-client
Pull Ceph updates from Ilya Dryomov:
"The highlights are:
- RADOS namespace support in libceph and CephFS (Zheng Yan and
myself). The stopgaps added in 4.5 to deny access to inodes in
namespaces are removed and CEPH_FEATURE_FS_FILE_LAYOUT_V2 feature
bit is now fully supported
- A large rework of the MDS cap flushing code (Zheng Yan)
- Handle some of ->d_revalidate() in RCU mode (Jeff Layton). We were
overly pessimistic before, bailing at the first sight of LOOKUP_RCU
On top of that we've got a few CephFS bug fixes, a couple of cleanups
and Arnd's workaround for a weird genksyms issue"
* tag 'ceph-for-4.8-rc1' of git://github.com/ceph/ceph-client: (34 commits)
ceph: fix symbol versioning for ceph_monc_do_statfs
ceph: Correctly return NXIO errors from ceph_llseek
ceph: Mark the file cache as unreclaimable
ceph: optimize cap flush waiting
ceph: cleanup ceph_flush_snaps()
ceph: kick cap flushes before sending other cap message
ceph: introduce an inode flag to indicates if snapflush is needed
ceph: avoid sending duplicated cap flush message
ceph: unify cap flush and snapcap flush
ceph: use list instead of rbtree to track cap flushes
ceph: update types of some local varibles
ceph: include 'follows' of pending snapflush in cap reconnect message
ceph: update cap reconnect message to version 3
ceph: mount non-default filesystem by name
libceph: fsmap.user subscription support
ceph: handle LOOKUP_RCU in ceph_d_revalidate
ceph: allow dentry_lease_is_valid to work under RCU walk
ceph: clear d_fsinfo pointer under d_lock
ceph: remove ceph_mdsc_lease_release
ceph: don't use ->d_time
...
Vegard Nossum [Tue, 2 Aug 2016 21:07:30 +0000 (14:07 -0700)]
kcov: allow more fine-grained coverage instrumentation
For more targeted fuzzing, it's better to disable kernel-wide
instrumentation and instead enable it on a per-subsystem basis. This
follows the pattern of UBSAN and allows you to compile in the kcov
driver without instrumenting the whole kernel.
To instrument a part of the kernel, you can use either
# for a single file in the current directory
KCOV_INSTRUMENT_filename.o := y
or
# for all the files in the current directory (excluding subdirectories)
KCOV_INSTRUMENT := y
or
# (same as above)
ccflags-y += $(CFLAGS_KCOV)
or
# for all the files in the current directory (including subdirectories)
subdir-ccflags-y += $(CFLAGS_KCOV)
init/Kconfig: add clarification for out-of-tree modules
It doesn't trim just symbols that are totally unused in-tree - it trims
the symbols unused by any in-tree modules actually built. If you've
done a 'make localmodconfig' and only build a hundred or so modules,
it's pretty likely that your out-of-tree module will come up lacking
something...
Hopefully this will save the next guy from a Homer Simpson "D'oh!"
moment.
Link: http://lkml.kernel.org/r/10177.1469787292@turing-police.cc.vt.edu Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu> Cc: Michal Marek <mmarek@suse.cz> Cc: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rob Herring [Tue, 2 Aug 2016 21:07:24 +0000 (14:07 -0700)]
config: add android config fragments
Copy the config fragments from the AOSP common kernel android-4.4
branch. It is becoming possible to run mainline kernels with Android,
but the kernel defconfigs don't work as-is and debugging missing config
options is a pain. Adding the config fragments into the kernel tree,
makes configuring a mainline kernel as simple as:
make ARCH=arm multi_v7_defconfig android-base.config android-recommended.config
The following non-upstream config options were removed:
Alexey Dobriyan [Tue, 2 Aug 2016 21:07:21 +0000 (14:07 -0700)]
init/Kconfig: ban CONFIG_LOCALVERSION_AUTO with allmodconfig
Doing patches with allmodconfig kernel compiled and committing stuff
into local tree have unfortunate consequence: kernel version changes (as
it should) leading to recompiling and relinking of several files even if
they weren't touched (or interesting at all). This and "git-whatever"
figuring out current version slow down compilation for no good reason.
But lets face it, "allmodconfig" kernels don't care about kernel
version, they are simply compile check guinea pigs.
Make LOCALVERSION_AUTO depend on !COMPILE_TEST, so it doesn't sneak into
allmodconfig .config.
Link: http://lkml.kernel.org/r/20160707214954.GC31678@p183.telecom.by Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Cc: Michal Marek <mmarek@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Akash Goel [Tue, 2 Aug 2016 21:07:18 +0000 (14:07 -0700)]
relay: add global mode support for buffer-only channels
Commit 20d8b67c06fa ("relay: add buffer-only channels; useful for early
logging") added support to use channels with no associated files.
This is useful when the exact location of relay file is not known or the
the parent directory of relay file is not available, while creating the
channel and the logging has to start right from the boot.
But there was no provision to use global mode with buffer-only channels,
which is added by this patch, without modifying the interface where
initially there will be a dummy invocation of create_buf_file callback
through which kernel client can convey the need of a global buffer.
For the use case where drivers/kernel clients want a simple interface
for the userspace, which enables them to capture data/logs from relay
file inorder & without any post processing, support of Global buffer
mode is warranted.
Modules, like i915, using relay_open() in early init would have to later
register their buffer-only relays, once debugfs is available, by calling
relay_late_setup_files(). Hence relay_late_setup_files() symbol also
needs to be exported.
Link: http://lkml.kernel.org/r/1468404563-11653-1-git-send-email-akash.goel@intel.com Signed-off-by: Akash Goel <akash.goel@intel.com> Cc: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro> Cc: Tom Zanussi <tzanussi@gmail.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prarit Bhargava [Tue, 2 Aug 2016 21:07:15 +0000 (14:07 -0700)]
init: allow blacklisting of module_init functions
sprint_symbol_no_offset() returns the string "function_name
[module_name]" where [module_name] is not printed for built in kernel
functions. This means that the blacklisting code will fail when
comparing module function names with the extended string.
This patch adds the functionality to block a module's module_init()
function by finding the space in the string and truncating the
comparison to that length.
Link: http://lkml.kernel.org/r/1466124387-20446-1-git-send-email-prarit@redhat.com Signed-off-by: Prarit Bhargava <prarit@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Yang Shi <yang.shi@linaro.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Mel Gorman <mgorman@suse.de> Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk> Cc: Kees Cook <keescook@chromium.org> Cc: Yaowei Bai <baiyaowei@cmss.chinamobile.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / mirror_ubuntu-kernels.git / log