Mike Rapoport [Fri, 28 Dec 2018 08:35:29 +0000 (00:35 -0800)]
memblock: replace usage of __memblock_free_early() with memblock_free()
__memblock_free_early() is only used by the convenience wrappers, so
essentially we wrap a call to memblock_free() twice. Replace calls of
__memblock_free_early() with calls to memblock_free() and drop the former.
Link: http://lkml.kernel.org/r/20181125102940.GE28634@rapoport-lnx Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Wentao Wang <witallwang@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Aaron Lu [Fri, 28 Dec 2018 08:35:18 +0000 (00:35 -0800)]
mm/page_alloc.c: free order-0 pages through PCP in page_frag_free()
page_frag_free() calls __free_pages_ok() to free the page back to Buddy.
This is OK for high order page, but for order-0 pages, it misses the
optimization opportunity of using Per-Cpu-Pages and can cause zone lock
contention when called frequently.
Pawel Staszewski recently shared his result of 'how Linux kernel handles
normal traffic'[1] and from perf data, Jesper Dangaard Brouer found the
lock contention comes from page allocator:
Jesper explained how it happened: mlx5 driver RX-page recycle mechanism is
not effective in this workload and pages have to go through the page
allocator. The lock contention happens during mlx5 DMA TX completion
cycle. And the page allocator cannot keep up at these speeds.[2]
I thought that __free_pages_ok() are mostly freeing high order pages and
thought this is an lock contention for high order pages but Jesper
explained in detail that __free_pages_ok() here are actually freeing
order-0 pages because mlx5 is using order-0 pages to satisfy its page pool
allocation request.[3]
The free path as pointed out by Jesper is:
skb_free_head()
-> skb_free_frag()
-> page_frag_free()
And the pages being freed on this path are order-0 pages.
Fix this by doing similar things as in __page_frag_cache_drain() - send
the being freed page to PCP if it's an order-0 page, or directly to Buddy
if it is a high order page.
With this change, Paweł hasn't noticed lock contention yet in his
workload and Jesper has noticed a 7% performance improvement using a micro
benchmark and lock contention is gone. Ilias' test on a 'low' speed 1Gbit
interface on an cortex-a53 shows ~11% performance boost testing with
64byte packets and __free_pages_ok() disappeared from perf top.
Dan Williams [Fri, 28 Dec 2018 08:35:15 +0000 (00:35 -0800)]
mm, hmm: mark hmm_devmem_{add, add_resource} EXPORT_SYMBOL_GPL
At Maintainer Summit, Greg brought up a topic I proposed around
EXPORT_SYMBOL_GPL usage. The motivation was considerations for when
EXPORT_SYMBOL_GPL is warranted and the criteria for taking the exceptional
step of reclassifying an existing export. Specifically, I wanted to make
the case that although the line is fuzzy and hard to specify in abstract
terms, it is nonetheless clear that devm_memremap_pages() and HMM
(Heterogeneous Memory Management) have crossed it. The
devm_memremap_pages() facility should have been EXPORT_SYMBOL_GPL from the
beginning, and HMM as a derivative of that functionality should have
naturally picked up that designation as well.
Contrary to typical rules, the HMM infrastructure was merged upstream with
zero in-tree consumers. There was a promise at the time that those users
would be merged "soon", but it has been over a year with no drivers
arriving. While the Nouveau driver is about to belatedly make good on
that promise it is clear that HMM was targeted first and foremost at an
out-of-tree consumer.
HMM is derived from devm_memremap_pages(), a facility Christoph and I
spearheaded to support persistent memory. It combines a device lifetime
model with a dynamically created 'struct page' / memmap array for any
physical address range. It enables coordination and control of the many
code paths in the kernel built to interact with memory via 'struct page'
objects. With HMM the integration goes even deeper by allowing device
drivers to hook and manipulate page fault and page free events.
One interpretation of when EXPORT_SYMBOL is suitable is when it is
exporting stable and generic leaf functionality. The
devm_memremap_pages() facility continues to see expanding use cases,
peer-to-peer DMA being the most recent, with no clear end date when it
will stop attracting reworks and semantic changes. It is not suitable to
export devm_memremap_pages() as a stable 3rd party driver API due to the
fact that it is still changing and manipulates core behavior. Moreover,
it is not in the best interest of the long term development of the core
memory management subsystem to permit any external driver to effectively
define its own system-wide memory management policies with no
encouragement to engage with upstream.
I am also concerned that HMM was designed in a way to minimize further
engagement with the core-MM. That, with these hooks in place,
device-drivers are free to implement their own policies without much
consideration for whether and how the core-MM could grow to meet that
need. Going forward not only should HMM be EXPORT_SYMBOL_GPL, but the
core-MM should be allowed the opportunity and stimulus to change and
address these new use cases as first class functionality.
Original changelog:
hmm_devmem_add(), and hmm_devmem_add_resource() duplicated
devm_memremap_pages() and are now simple now wrappers around the core
facility to inject a dev_pagemap instance into the global pgmap_radix and
hook page-idle events. The devm_memremap_pages() interface is base
infrastructure for HMM. HMM has more and deeper ties into the kernel
memory management implementation than base ZONE_DEVICE which is itself a
EXPORT_SYMBOL_GPL facility.
Originally, the HMM page structure creation routines copied the
devm_memremap_pages() code and reused ZONE_DEVICE. A cleanup to unify the
implementations was discussed during the initial review:
http://lkml.iu.edu/hypermail/linux/kernel/1701.2/00812.html Recent work to
extend devm_memremap_pages() for the peer-to-peer-DMA facility enabled
this cleanup to move forward.
In addition to the integration with devm_memremap_pages() HMM depends on
other GPL-only symbols:
It goes further to consume / indirectly expose functionality that is not
exported to any other driver:
alloc_pages_vma
walk_page_range
HMM is derived from devm_memremap_pages(), and extends deep core-kernel
fundamentals. Similar to devm_memremap_pages(), mark its entry points
EXPORT_SYMBOL_GPL().
[logang@deltatee.com: PCI/P2PDMA: match interface changes to devm_memremap_pages()] Link: http://lkml.kernel.org/r/20181130225911.2900-1-logang@deltatee.com Link: http://lkml.kernel.org/r/154275560565.76910.15919297436557795278.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Logan Gunthorpe <logang@deltatee.com> Cc: "Jérôme Glisse" <jglisse@redhat.com> Cc: Balbir Singh <bsingharora@gmail.com>, Cc: Michal Hocko <mhocko@suse.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Williams [Fri, 28 Dec 2018 08:35:11 +0000 (00:35 -0800)]
mm, hmm: replace hmm_devmem_pages_create() with devm_memremap_pages()
Commit e8d513483300 ("memremap: change devm_memremap_pages interface to
use struct dev_pagemap") refactored devm_memremap_pages() to allow a
dev_pagemap instance to be supplied. Passing in a dev_pagemap interface
simplifies the design of pgmap type drivers in that they can rely on
container_of() to lookup any private data associated with the given
dev_pagemap instance.
In addition to the cleanups this also gives hmm users multi-order-radix
improvements that arrived with commit ab1b597ee0e4 "mm,
devm_memremap_pages: use multi-order radix for ZONE_DEVICE lookups"
As part of the conversion to the devm_memremap_pages() method of
handling the percpu_ref relative to when pages are put, the percpu_ref
completion needs to move to hmm_devmem_ref_exit(). See 71389703839e
("mm, zone_device: Replace {get, put}_zone_device_page...") for details.
Link: http://lkml.kernel.org/r/154275560053.76910.10870962637383152392.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jérôme Glisse <jglisse@redhat.com> Acked-by: Balbir Singh <bsingharora@gmail.com> Cc: Logan Gunthorpe <logang@deltatee.com> Cc: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Williams [Fri, 28 Dec 2018 08:35:07 +0000 (00:35 -0800)]
mm, hmm: use devm semantics for hmm_devmem_{add, remove}
devm semantics arrange for resources to be torn down when
device-driver-probe fails or when device-driver-release completes.
Similar to devm_memremap_pages() there is no need to support an explicit
remove operation when the users properly adhere to devm semantics.
Note that devm_kzalloc() automatically handles allocating node-local
memory.
Link: http://lkml.kernel.org/r/154275559545.76910.9186690723515469051.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jérôme Glisse <jglisse@redhat.com> Cc: "Jérôme Glisse" <jglisse@redhat.com> Cc: Logan Gunthorpe <logang@deltatee.com> Cc: Balbir Singh <bsingharora@gmail.com> Cc: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Williams [Fri, 28 Dec 2018 08:35:01 +0000 (00:35 -0800)]
mm, devm_memremap_pages: add MEMORY_DEVICE_PRIVATE support
In preparation for consolidating all ZONE_DEVICE enabling via
devm_memremap_pages(), teach it how to handle the constraints of
MEMORY_DEVICE_PRIVATE ranges.
[jglisse@redhat.com: call move_pfn_range_to_zone for MEMORY_DEVICE_PRIVATE] Link: http://lkml.kernel.org/r/154275559036.76910.12434636179931292607.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Jérôme Glisse <jglisse@redhat.com> Acked-by: Christoph Hellwig <hch@lst.de> Reported-by: Logan Gunthorpe <logang@deltatee.com> Reviewed-by: Logan Gunthorpe <logang@deltatee.com> Cc: Balbir Singh <bsingharora@gmail.com> Cc: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Williams [Fri, 28 Dec 2018 08:34:57 +0000 (00:34 -0800)]
mm, devm_memremap_pages: fix shutdown handling
The last step before devm_memremap_pages() returns success is to allocate
a release action, devm_memremap_pages_release(), to tear the entire setup
down. However, the result from devm_add_action() is not checked.
Checking the error from devm_add_action() is not enough. The api
currently relies on the fact that the percpu_ref it is using is killed by
the time the devm_memremap_pages_release() is run. Rather than continue
this awkward situation, offload the responsibility of killing the
percpu_ref to devm_memremap_pages_release() directly. This allows
devm_memremap_pages() to do the right thing relative to init failures and
shutdown.
Without this change we could fail to register the teardown of
devm_memremap_pages(). The likelihood of hitting this failure is tiny as
small memory allocations almost always succeed. However, the impact of
the failure is large given any future reconfiguration, or disable/enable,
of an nvdimm namespace will fail forever as subsequent calls to
devm_memremap_pages() will fail to setup the pgmap_radix since there will
be stale entries for the physical address range.
An argument could be made to require that the ->kill() operation be set in
the @pgmap arg rather than passed in separately. However, it helps code
readability, tracking the lifetime of a given instance, to be able to grep
the kill routine directly at the devm_memremap_pages() call site.
Link: http://lkml.kernel.org/r/154275558526.76910.7535251937849268605.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Fixes: e8d513483300 ("memremap: change devm_memremap_pages interface...") Reviewed-by: "Jérôme Glisse" <jglisse@redhat.com> Reported-by: Logan Gunthorpe <logang@deltatee.com> Reviewed-by: Logan Gunthorpe <logang@deltatee.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Balbir Singh <bsingharora@gmail.com> Cc: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Williams [Fri, 28 Dec 2018 08:34:54 +0000 (00:34 -0800)]
mm, devm_memremap_pages: kill mapping "System RAM" support
Given the fact that devm_memremap_pages() requires a percpu_ref that is
torn down by devm_memremap_pages_release() the current support for mapping
RAM is broken.
Support for remapping "System RAM" has been broken since the beginning and
there is no existing user of this this code path, so just kill the support
and make it an explicit error.
This cleanup also simplifies a follow-on patch to fix the error path when
setting a devm release action for devm_memremap_pages_release() fails.
Link: http://lkml.kernel.org/r/154275557997.76910.14689813630968180480.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: "Jérôme Glisse" <jglisse@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Logan Gunthorpe <logang@deltatee.com> Cc: Balbir Singh <bsingharora@gmail.com> Cc: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Williams [Fri, 28 Dec 2018 08:34:50 +0000 (00:34 -0800)]
mm, devm_memremap_pages: mark devm_memremap_pages() EXPORT_SYMBOL_GPL
devm_memremap_pages() is a facility that can create struct page entries
for any arbitrary range and give drivers the ability to subvert core
aspects of page management.
Specifically the facility is tightly integrated with the kernel's memory
hotplug functionality. It injects an altmap argument deep into the
architecture specific vmemmap implementation to allow allocating from
specific reserved pages, and it has Linux specific assumptions about page
structure reference counting relative to get_user_pages() and
get_user_pages_fast(). It was an oversight and a mistake that this was
not marked EXPORT_SYMBOL_GPL from the outset.
Again, devm_memremap_pagex() exposes and relies upon core kernel internal
assumptions and will continue to evolve along with 'struct page', memory
hotplug, and support for new memory types / topologies. Only an in-kernel
GPL-only driver is expected to keep up with this ongoing evolution. This
interface, and functionality derived from this interface, is not suitable
for kernel-external drivers.
Link: http://lkml.kernel.org/r/154275557457.76910.16923571232582744134.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Michal Hocko <mhocko@suse.com> Cc: "Jérôme Glisse" <jglisse@redhat.com> Cc: Balbir Singh <bsingharora@gmail.com> Cc: Logan Gunthorpe <logang@deltatee.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Biggers [Fri, 28 Dec 2018 08:34:43 +0000 (00:34 -0800)]
userfaultfd: convert userfaultfd_ctx::refcount to refcount_t
Reference counters should use refcount_t rather than atomic_t, since the
refcount_t implementation can prevent overflows, reducing the
exploitability of reference leak bugs. userfaultfd_ctx::refcount is a
reference counter with the usual semantics, so convert it to refcount_t.
Note: I replaced the BUG() on incrementing a 0 refcount with just
refcount_inc(), since part of the semantics of refcount_t is that that
incrementing a 0 refcount is not allowed; with CONFIG_REFCOUNT_FULL,
refcount_inc() already checks for it and warns.
Link: http://lkml.kernel.org/r/20181115003916.63381-1-ebiggers@kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Aaron Lu [Fri, 28 Dec 2018 08:34:39 +0000 (00:34 -0800)]
mm/swap: use nr_node_ids for avail_lists in swap_info_struct
Since a2468cc9bfdf ("swap: choose swap device according to numa node"),
avail_lists field of swap_info_struct is changed to an array with
MAX_NUMNODES elements. This made swap_info_struct size increased to 40KiB
and needs an order-4 page to hold it.
This is not optimal in that:
1 Most systems have way less than MAX_NUMNODES(1024) nodes so it
is a waste of memory;
2 It could cause swapon failure if the swap device is swapped on
after system has been running for a while, due to no order-4
page is available as pointed out by Vasily Averin.
Solve the above two issues by using nr_node_ids(which is the actual
possible node number the running system has) for avail_lists instead of
MAX_NUMNODES.
nr_node_ids is unknown at compile time so can't be directly used when
declaring this array. What I did here is to declare avail_lists as zero
element array and allocate space for it when allocating space for
swap_info_struct. The reason why keep using array but not pointer is
plist_for_each_entry needs the field to be part of the struct, so pointer
will not work.
This patch is on top of Vasily Averin's fix commit. I think the use of
kvzalloc for swap_info_struct is still needed in case nr_node_ids is
really big on some systems.
Link: http://lkml.kernel.org/r/20181115083847.GA11129@intel.com Signed-off-by: Aaron Lu <aaron.lu@intel.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Vasily Averin <vvs@virtuozzo.com> Cc: Huang Ying <ying.huang@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wei Yang [Fri, 28 Dec 2018 08:34:36 +0000 (00:34 -0800)]
vmscan: return NODE_RECLAIM_NOSCAN in node_reclaim() when CONFIG_NUMA is n
Commit fa5e084e43eb ("vmscan: do not unconditionally treat zones that
fail zone_reclaim() as full") changed the return value of
node_reclaim(). The original return value 0 means NODE_RECLAIM_SOME
after this commit.
While the return value of node_reclaim() when CONFIG_NUMA is n is not
changed. This will leads to call zone_watermark_ok() again.
This patch fixes the return value by adjusting to NODE_RECLAIM_NOSCAN.
Since node_reclaim() is only called in page_alloc.c, move it to
mm/internal.h.
Link: http://lkml.kernel.org/r/20181113080436.22078-1-richard.weiyang@gmail.com Signed-off-by: Wei Yang <richard.weiyang@gmail.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Matthew Wilcox <willy@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arun KS [Fri, 28 Dec 2018 08:34:32 +0000 (00:34 -0800)]
mm: remove managed_page_count_lock spinlock
Now that totalram_pages and managed_pages are atomic varibles, no need of
managed_page_count spinlock. The lock had really a weak consistency
guarantee. It hasn't been used for anything but the update but no reader
actually cares about all the values being updated to be in sync.
Link: http://lkml.kernel.org/r/1542090790-21750-5-git-send-email-arunks@codeaurora.org Signed-off-by: Arun KS <arunks@codeaurora.org> Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: David Hildenbrand <david@redhat.com> Reviewed-by: Pavel Tatashin <pasha.tatashin@soleen.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arun KS [Fri, 28 Dec 2018 08:34:29 +0000 (00:34 -0800)]
mm: convert totalram_pages and totalhigh_pages variables to atomic
totalram_pages and totalhigh_pages are made static inline function.
Main motivation was that managed_page_count_lock handling was complicating
things. It was discussed in length here,
https://lore.kernel.org/patchwork/patch/995739/#1181785 So it seemes
better to remove the lock and convert variables to atomic, with preventing
poteintial store-to-read tearing as a bonus.
[akpm@linux-foundation.org: coding style fixes] Link: http://lkml.kernel.org/r/1542090790-21750-4-git-send-email-arunks@codeaurora.org Signed-off-by: Arun KS <arunks@codeaurora.org> Suggested-by: Michal Hocko <mhocko@suse.com> Suggested-by: Vlastimil Babka <vbabka@suse.cz> Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Reviewed-by: Pavel Tatashin <pasha.tatashin@soleen.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: David Hildenbrand <david@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arun KS [Fri, 28 Dec 2018 08:34:24 +0000 (00:34 -0800)]
mm: convert zone->managed_pages to atomic variable
totalram_pages, zone->managed_pages and totalhigh_pages updates are
protected by managed_page_count_lock, but readers never care about it.
Convert these variables to atomic to avoid readers potentially seeing a
store tear.
This patch converts zone->managed_pages. Subsequent patches will convert
totalram_panges, totalhigh_pages and eventually managed_page_count_lock
will be removed.
Main motivation was that managed_page_count_lock handling was complicating
things. It was discussed in length here,
https://lore.kernel.org/patchwork/patch/995739/#1181785 So it seemes
better to remove the lock and convert variables to atomic, with preventing
poteintial store-to-read tearing as a bonus.
Link: http://lkml.kernel.org/r/1542090790-21750-3-git-send-email-arunks@codeaurora.org Signed-off-by: Arun KS <arunks@codeaurora.org> Suggested-by: Michal Hocko <mhocko@suse.com> Suggested-by: Vlastimil Babka <vbabka@suse.cz> Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Reviewed-by: David Hildenbrand <david@redhat.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Reviewed-by: Pavel Tatashin <pasha.tatashin@soleen.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arun KS [Fri, 28 Dec 2018 08:34:20 +0000 (00:34 -0800)]
mm: reference totalram_pages and managed_pages once per function
Patch series "mm: convert totalram_pages, totalhigh_pages and managed
pages to atomic", v5.
This series converts totalram_pages, totalhigh_pages and
zone->managed_pages to atomic variables.
totalram_pages, zone->managed_pages and totalhigh_pages updates are
protected by managed_page_count_lock, but readers never care about it.
Convert these variables to atomic to avoid readers potentially seeing a
store tear.
Main motivation was that managed_page_count_lock handling was complicating
things. It was discussed in length here,
https://lore.kernel.org/patchwork/patch/995739/#1181785 It seemes better
to remove the lock and convert variables to atomic. With the change,
preventing poteintial store-to-read tearing comes as a bonus.
This patch (of 4):
This is in preparation to a later patch which converts totalram_pages and
zone->managed_pages to atomic variables. Please note that re-reading the
value might lead to a different value and as such it could lead to
unexpected behavior. There are no known bugs as a result of the current
code but it is better to prevent from them in principle.
Link: http://lkml.kernel.org/r/1542090790-21750-2-git-send-email-arunks@codeaurora.org Signed-off-by: Arun KS <arunks@codeaurora.org> Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Reviewed-by: David Hildenbrand <david@redhat.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Reviewed-by: Pavel Tatashin <pasha.tatashin@soleen.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 28 Dec 2018 08:34:13 +0000 (00:34 -0800)]
mm, memory_hotplug: do not clear numa_node association after hot_remove
Per-cpu numa_node provides a default node for each possible cpu. The
association gets initialized during the boot when the architecture
specific code explores cpu->NUMA affinity. When the whole NUMA node is
removed though we are clearing this association
This means that whoever calls cpu_to_node for a cpu associated with such a
node will get NUMA_NO_NODE. This is problematic for two reasons. First
it is fragile because __alloc_pages_node would simply blow up on an
out-of-bound access. We have encountered this when loading kvm module
on an older kernel but the code is basically the same in the current Linus
tree as well. alloc_vmcs_cpu could use alloc_pages_nodemask which would
recognize NUMA_NO_NODE and use alloc_pages_node which would translate it
to numa_mem_id but that is wrong as well because it would use a cpu
affinity of the local CPU which might be quite far from the original node.
It is also reasonable to expect that cpu_to_node will provide a sane
value and there might be many more callers like that.
The second problem is that __register_one_node relies on cpu_to_node to
properly associate cpus back to the node when it is onlined. We do not
want to lose that link as there is no arch independent way to get it from
the early boot time AFAICS.
Drop the whole check_and_unmap_cpu_on_node machinery and keep the
association to fix both issues. The NODE_DATA(nid) is not deallocated so
it will stay in place and if anybody wants to allocate from that node then
a fallback node will be used.
Thanks to Vlastimil Babka for his live system debugging skills that helped
debugging the issue.
Link: http://lkml.kernel.org/r/20181108100413.966-1-mhocko@kernel.org Fixes: e13fe8695c57 ("cpu-hotplug,memory-hotplug: clear cpu_to_node() when offlining the node") Signed-off-by: Michal Hocko <mhocko@suse.com> Debugged-by: Vlastimil Babka <vbabka@suse.cz> Reported-by: Miroslav Benes <mbenes@suse.cz> Acked-by: Anshuman Khandual <anshuman.khandual@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yangtao Li [Fri, 28 Dec 2018 08:34:09 +0000 (00:34 -0800)]
mm/mmap.c: remove verify_mm_writelocked()
We should get rid of this function. It no longer serves its purpose.
This is a historical artifact from 2005 where do_brk was called outside of
the core mm. We do have a proper abstraction in vm_brk_flags and that one
does the locking properly so there is no need to use this function.
Link: http://lkml.kernel.org/r/20181108174856.10811-1-tiny.windzz@gmail.com Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: David Rientjes <rientjes@google.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As jhash2 always will be slower (for data size like PAGE_SIZE). Don't use
it in ksm at all.
Use only xxhash for now, because for using crc32c, cryptoapi must be
initialized first - that requires some tricky solution to work well in all
situations.
Link: http://lkml.kernel.org/r/20181023182554.23464-3-nefelim4ag@gmail.com Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com> Signed-off-by: leesioh <solee@os.korea.ac.kr> Reviewed-by: Pavel Tatashin <pavel.tatashin@microsoft.com> Reviewed-by: Mike Rapoport <rppt@linux.vnet.ibm.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Experiment process:
Firstly, we turn off KSM and launch 4 VMs. Then we turn on the KSM and
measure the checksum computation time until full_scans become two.
The experimental results (the experimental value is the average of the measured values)
crc32c_intel: 1084.10ns
crc32c (no hardware acceleration): 7012.51ns
xxhash32: 2227.75ns
xxhash64: 1413.16ns
jhash2: 5128.30ns
In summary, the result shows that crc32c_intel has advantages over all of
the hash function used in the experiment. (decreased by 84.54% compared
to crc32c, 78.86% compared to jhash2, 51.33% xxhash32, 23.28% compared to
xxhash64) the results are similar to those of Timofey.
But, use only xxhash for now, because for using crc32c, cryptoapi must be
initialized first - that require some tricky solution to work good in all
situations.
So:
- First patch implement compile time pickup of fastest implementation of
xxhash for target platform.
- The second patch replaces jhash2 with xxhash
This patch (of 2):
xxh32() - fast on both 32/64-bit platforms
xxh64() - fast only on 64-bit platform
Create xxhash() which will pick up the fastest version at compile time.
Link: http://lkml.kernel.org/r/20181023182554.23464-2-nefelim4ag@gmail.com Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com> Reviewed-by: Pavel Tatashin <pavel.tatashin@microsoft.com> Reviewed-by: Mike Rapoport <rppt@linux.vnet.ibm.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: leesioh <solee@os.korea.ac.kr> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
which are not triggered by the memory hotplug but rather CMA allocator.
The original idea behind dumping the page state for all call paths was
that these messages will be helpful debugging failures. From the above it
seems that this is not the case for the CMA path because we are lacking
much more context. E.g the second reported page might be a CMA allocated
page. It is still interesting to see a slab page in the CMA area but it
is hard to tell whether this is bug from the above output alone.
Address this issue by dumping the page state only on request. Both
start_isolate_page_range and has_unmovable_pages already have an argument
to ignore hwpoison pages so make this argument more generic and turn it
into flags and allow callers to combine non-default modes into a mask.
While we are at it, has_unmovable_pages call from
is_pageblock_removable_nolock (sysfs removable file) is questionable to
report the failure so drop it from there as well.
Link: http://lkml.kernel.org/r/20181218092802.31429-1-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 28 Dec 2018 08:33:53 +0000 (00:33 -0800)]
mm, memory_hotplug: be more verbose for memory offline failures
There is only very limited information printed when the memory offlining
fails:
[ 1984.506184] rac1 kernel: memory offlining [mem 0x82600000000-0x8267fffffff] failed due to signal backoff
This tells us that the failure is triggered by the userspace intervention
but it doesn't tell us much more about the underlying reason. It might be
that the page migration failes repeatedly and the userspace timeout
expires and send a signal or it might be some of the earlier steps
(isolation, memory notifier) takes too long.
If the migration failes then it would be really helpful to see which page
that and its state. The same applies to the isolation phase. If we fail
to isolate a page from the allocator then knowing the state of the page
would be helpful as well.
Dump the page state that fails to get isolated or migrated. This will
tell us more about the failure and what to focus on during debugging.
[akpm@linux-foundation.org: add missing printk arg]
[mhocko@suse.com: tweak dump_page() `reason' text] Link: http://lkml.kernel.org/r/20181116083020.20260-6-mhocko@kernel.org Link: http://lkml.kernel.org/r/20181107101830.17405-6-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Oscar Salvador <osalvador@suse.de> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Baoquan He <bhe@redhat.com> Cc: Oscar Salvador <OSalvador@suse.com> Cc: William Kucharski <william.kucharski@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 28 Dec 2018 08:33:49 +0000 (00:33 -0800)]
mm, memory_hotplug: print reason for the offlining failure
The memory offlining failure reporting is inconsistent and insufficient.
Some error paths simply do not report the failure to the log at all. When
we do report there are no details about the reason of the failure and
there are several of them which makes memory offlining failures hard to
debug.
Make sure that the
memory offlining [mem %#010llx-%#010llx] failed
message is printed for all failures and also provide a short textual
reason for the failure e.g.
[ 1984.506184] rac1 kernel: memory offlining [mem 0x82600000000-0x8267fffffff] failed due to signal backoff
this tells us that the offlining has failed because of a signal pending
aka user intervention.
[akpm@linux-foundation.org: tweak messages a bit] Link: http://lkml.kernel.org/r/20181107101830.17405-5-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Oscar Salvador <osalvador@suse.de> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Baoquan He <bhe@redhat.com> Cc: Oscar Salvador <OSalvador@suse.com> Cc: William Kucharski <william.kucharski@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 28 Dec 2018 08:33:45 +0000 (00:33 -0800)]
mm, memory_hotplug: drop pointless block alignment checks from __offline_pages
This function is never called from a context which would provide
misaligned pfn range so drop the pointless check.
Link: http://lkml.kernel.org/r/20181107101830.17405-4-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Oscar Salvador <osalvador@suse.de> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Baoquan He <bhe@redhat.com> Cc: Oscar Salvador <OSalvador@suse.com> Cc: William Kucharski <william.kucharski@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 28 Dec 2018 08:33:42 +0000 (00:33 -0800)]
mm: lower the printk loglevel for __dump_page messages
__dump_page messages use KERN_EMERG resp. KERN_ALERT loglevel (this is
the case since 2004). Most callers of this function are really detecting
a critical page state and BUG right after. On the other hand the function
is called also from contexts which just want to inform about the page
state and those would rather not disrupt logs that much (e.g. some
systems route these messages to the normal console).
Reduce the loglevel to KERN_WARNING to make dump_page easier to reuse for
other contexts while those messages will still make it to the kernel log
in most setups. Even if the loglevel setup filters warnings away those
paths that are really critical already print the more targeted error or
panic and that should make it to the kernel log.
[mhocko@kernel.org: fix __dump_page()] Link: http://lkml.kernel.org/r/20181212142540.GA7378@dhcp22.suse.cz
[akpm@linux-foundation.org: s/KERN_WARN/KERN_WARNING/, per Michal] Link: http://lkml.kernel.org/r/20181107101830.17405-3-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Baoquan He <bhe@redhat.com> Cc: Oscar Salvador <OSalvador@suse.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: William Kucharski <william.kucharski@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 28 Dec 2018 08:33:38 +0000 (00:33 -0800)]
mm: print more information about mapping in __dump_page
I have been promissing to improve memory offlining failures debugging for
quite some time. As things stand now we get only very limited information
in the kernel log when the offlining fails. It is usually only
with no further details. We do not know what exactly fails and for what
reason. Whenever I was forced to debug such a failure I've always had to
do a debugging patch to tell me more. We can enable some tracepoints but
it would be much better to get a better picture without using them.
This patch series does 2 things. The first one is to make dump_page more
usable by printing more information about the mapping patch 1. Then it
reduces the log level from emerg to warning so that this function is
usable from less critical context patch 2. Then I have added more
detailed information about the offlining failure patch 4 and finally add
dump_page to isolation and offlining migration paths. Patch 3 is a
trivial cleanup.
This patch (of 6):
__dump_page prints the mapping pointer but that is quite unhelpful for
many reports because the pointer itself only helps to distinguish anon/ksm
mappings from other ones (because of lowest bits set). Sometimes it would
be much more helpful to know what kind of mapping that is actually and if
we know this is a file mapping then also try to resolve the dentry name.
Anders Roxell [Fri, 28 Dec 2018 08:33:31 +0000 (00:33 -0800)]
writeback: don't decrement wb->refcnt if !wb->bdi
This happened while running in qemu-system-aarch64, the AMBA PL011 UART
driver when enabling CONFIG_DEBUG_TEST_DRIVER_REMOVE.
arch_initcall(pl011_init) came before subsys_initcall(default_bdi_init),
devtmpfs' handle_remove() crashes because the reference count is a NULL
pointer only because wb->bdi hasn't been initialized yet.
Rework so that wb_put have an extra check if wb->bdi before decrement
wb->refcnt and also add a WARN_ON_ONCE to get a warning if it happens
again in other drivers.
Link: http://lkml.kernel.org/r/20181030113545.30999-2-anders.roxell@linaro.org Fixes: 52ebea749aae ("writeback: make backing_dev_info host cgroup-specific bdi_writebacks") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Co-developed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Contrary to its name, mmu_notifier_synchronize() does not synchronize the
notifier's SRCU instance, but rather waits for RCU callbacks to finish.
i.e. it invokes rcu_barrier(). The RCU documentation is quite clear on
this matter, explicitly calling out that rcu_barrier() does not imply
synchronize_rcu().
As there are no callers of mmu_notifier_synchronize() and it's unclear
whether any user of mmu_notifier_call_srcu() will ever want to barrier on
their callbacks, simply remove the function.
Link: http://lkml.kernel.org/r/20181106134705.14197-1-sean.j.christopherson@intel.com Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Jérôme Glisse <jglisse@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Balbir Singh [Fri, 28 Dec 2018 08:33:24 +0000 (00:33 -0800)]
mm/hotplug: optimize clear_hwpoisoned_pages()
In hot remove, we try to clear poisoned pages, but a small optimization to
check if num_poisoned_pages is 0 helps remove the iteration through
nr_pages.
Miles Chen [Fri, 28 Dec 2018 08:33:21 +0000 (00:33 -0800)]
mm/page_owner: clamp read count to PAGE_SIZE
The (root-only) page owner read might allocate a large size of memory with
a large read count. Allocation fails can easily occur when doing high
order allocations.
Clamp buffer size to PAGE_SIZE to avoid arbitrary size allocation
and avoid allocation fails due to high order allocation.
[akpm@linux-foundation.org: use min_t()] Link: http://lkml.kernel.org/r/1541091607-27402-1-git-send-email-miles.chen@mediatek.com Signed-off-by: Miles Chen <miles.chen@mediatek.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Joe Perches <joe@perches.com> Cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vlastimil Babka [Fri, 28 Dec 2018 08:33:17 +0000 (00:33 -0800)]
include/linux/slab.h: fix sparse warning in kmalloc_type()
Multiple people have reported the following sparse warning:
./include/linux/slab.h:332:43: warning: dubious: x & !y
The minimal fix would be to change the logical & to boolean &&, which
emits the same code, but Andrew has suggested that the branch-avoiding
tricks are maybe not worthwile. David Laight provided a nice comparison
of disassembly of multiple variants, which shows that the current version
produces a 4 deep dependency chain, and fixing the sparse warning by
changing logical and to multiplication emits an IMUL, making it even more
expensive.
The code as rewritten by this patch yielded the best disassembly, with a
single predictable branch for the most common case, and a ternary operator
for the rest, which gcc seems to compile without a branch or cmov by
itself.
The result should be more readable, without a sparse warning and probably
also faster for the common case.
Link: http://lkml.kernel.org/r/80340595-d7c5-97b9-4f6c-23fa893a91e9@suse.cz Fixes: 1291523f2c1d ("mm, slab/slub: introduce kmalloc-reclaimable caches") Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Reported-by: Bart Van Assche <bvanassche@acm.org> Reported-by: Darryl T. Agostinelli <dagostinelli@gmail.com> Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com> Suggested-by: Andrew Morton <akpm@linux-foundation.org> Suggested-by: David Laight <David.Laight@ACULAB.COM> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wei Yang [Fri, 28 Dec 2018 08:33:13 +0000 (00:33 -0800)]
mm/slub.c: record final state of slub action in deactivate_slab()
If __cmpxchg_double_slab() fails and (l != m), current code records
transition states of slub action.
Update the action after __cmpxchg_double_slab() success to record the
final state.
[akpm@linux-foundation.org: more whitespace cleanup] Link: http://lkml.kernel.org/r/20181107013119.3816-1-richard.weiyang@gmail.com Signed-off-by: Wei Yang <richard.weiyang@gmail.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wei Yang [Fri, 28 Dec 2018 08:33:09 +0000 (00:33 -0800)]
mm/slub.c: page is always non-NULL in node_match()
node_match() is a static function and is only invoked in slub.c.
In all three places, `page' is ensured to be valid.
Link: http://lkml.kernel.org/r/20181106150245.1668-1-richard.weiyang@gmail.com Signed-off-by: Wei Yang <richard.weiyang@gmail.com> Acked-by: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wei Yang [Fri, 28 Dec 2018 08:33:06 +0000 (00:33 -0800)]
mm/slub.c: remove validation on cpu_slab in __flush_cpu_slab()
cpu_slab is a per cpu variable which is allocated in all or none. If a
cpu_slab failed to be allocated, the slub is not usable.
We could use cpu_slab without validation in __flush_cpu_slab().
Link: http://lkml.kernel.org/r/20181103141218.22844-1-richard.weiyang@gmail.com Signed-off-by: Wei Yang <richard.weiyang@gmail.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Junxiao Bi [Fri, 28 Dec 2018 08:32:57 +0000 (00:32 -0800)]
ocfs2: don't clear bh uptodate for block read
For sync io read in ocfs2_read_blocks_sync(), first clear bh uptodate flag
and submit the io, second wait io done, last check whether bh uptodate, if
not return io error.
If two sync io for the same bh were issued, it could be the first io done
and set uptodate flag, but just before check that flag, the second io came
in and cleared uptodate, then ocfs2_read_blocks_sync() for the first io
will return IO error.
Indeed it's not necessary to clear uptodate flag, as the io end handler
end_buffer_read_sync() will set or clear it based on io succeed or failed.
The following message was found from a nfs server but the underlying
storage returned no error.
[4106438.567376] (nfsd,7146,3):ocfs2_get_suballoc_slot_bit:2780 ERROR: read block 1238823695 failed -5
[4106438.567569] (nfsd,7146,3):ocfs2_get_suballoc_slot_bit:2812 ERROR: status = -5
[4106438.567611] (nfsd,7146,3):ocfs2_test_inode_bit:2894 ERROR: get alloc slot and bit failed -5
[4106438.567643] (nfsd,7146,3):ocfs2_test_inode_bit:2932 ERROR: status = -5
[4106438.567675] (nfsd,7146,3):ocfs2_get_dentry:94 ERROR: test inode bit failed -5
Same issue in non sync read ocfs2_read_blocks(), fixed it as well.
Link: http://lkml.kernel.org/r/20181121020023.3034-4-junxiao.bi@oracle.com Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by: Changwei Ge <ge.changwei@h3c.com> Reviewed-by: Yiwen Jiang <jiangyiwen@huawei.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Jun Piao <piaojun@huawei.com> Cc: Mark Fasheh <mfasheh@versity.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Junxiao Bi [Fri, 28 Dec 2018 08:32:53 +0000 (00:32 -0800)]
ocfs2: clear journal dirty flag after shutdown journal
Dirty flag of the journal should be cleared at the last stage of umount,
if do it before jbd2_journal_destroy(), then some metadata in uncommitted
transaction could be lost due to io error, but as dirty flag of journal
was already cleared, we can't find that until run a full fsck. This may
cause system panic or other corruption.
Link: http://lkml.kernel.org/r/20181121020023.3034-3-junxiao.bi@oracle.com Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by: Yiwen Jiang <jiangyiwen@huawei.com> Reviewed-by: Joseph Qi <jiangqi903@gmail.com> Cc: Jun Piao <piaojun@huawei.com> Cc: Changwei Ge <ge.changwei@h3c.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@versity.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Junxiao Bi [Fri, 28 Dec 2018 08:32:50 +0000 (00:32 -0800)]
ocfs2: fix panic due to unrecovered local alloc
mount.ocfs2 ignore the inconsistent error that journal is clean but
local alloc is unrecovered. After mount, local alloc not empty, then
reserver cluster didn't alloc a new local alloc window, reserveration
map is empty(ocfs2_reservation_map.m_bitmap_len = 0), that triggered the
following panic.
and was advised to fixed during mount. But this is a very unusual
inconsistent state, usually journal dirty flag should be cleared at the
last stage of umount until every other things go right. We may need do
further debug to check that. Any way to avoid possible futher
corruption, mount should be abort and fsck should be run.
Larry Chen [Fri, 28 Dec 2018 08:32:46 +0000 (00:32 -0800)]
ocfs2: improve ocfs2 Makefile
Included file path was hard-wired in the ocfs2 makefile, which might
causes some confusion when compiling ocfs2 as an external module.
Say if we compile ocfs2 module as following.
cp -r /kernel/tree/fs/ocfs2 /other/dir/ocfs2
cd /other/dir/ocfs2
make -C /path/to/kernel_source M=`pwd` modules
Acutally, the compiler wil try to find included file in
/kernel/tree/fs/ocfs2, rather than the directory /other/dir/ocfs2.
To fix this little bug, we introduce the var $(src) provided by kbuild.
$(src) means the absolute path of the running kbuild file.
Link: http://lkml.kernel.org/r/20181108085546.15149-1-lchen@suse.com Signed-off-by: Larry Chen <lchen@suse.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Changwei Ge <ge.changwei@h3c.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jia Guo [Fri, 28 Dec 2018 08:32:35 +0000 (00:32 -0800)]
ocfs2: optimize the reading of heartbeat data
Reading heartbeat data from lowest node rather than from zero, in cases
where the node is not defined from zero, can reduce the number of sectors
read.
Here is a simple test data obtained with 'iostat -dmx dm-5 2', with
two nodes in the cluster, node number 10, 20, respectively.
Qian Cai [Fri, 28 Dec 2018 08:32:32 +0000 (00:32 -0800)]
debugobjects: call debug_objects_mem_init eariler
The current value of the early boot static pool size, 1024 is not big
enough for systems with large number of CPUs with timer or/and workqueue
objects selected. As the results, systems have 60+ CPUs with both timer
and workqueue objects enabled could trigger "ODEBUG: Out of memory.
ODEBUG disabled".
Some debug objects are allocated during the early boot. Enabling some
options like timers or workqueue objects may increase the size required
significantly with large number of CPUs. For example,
plus No. CPUs x 6 (workqueue) objects:
workqueue_init_early
alloc_workqueue
__alloc_workqueue_key
alloc_and_link_pwqs
init_pwq
Also, plus No. CPUs objects:
perf_event_init
__init_srcu_struct
init_srcu_struct_fields
init_srcu_struct_nodes
__init_work
However, none of the things are actually used or required before
debug_objects_mem_init() is invoked, so just move the call right before
vmalloc_init().
According to tglx, "the reason why the call is at this place in
start_kernel() is historical. It's because back in the days when
debugobjects were added the memory allocator was enabled way later than
today."
Link: http://lkml.kernel.org/r/20181126102407.1836-1-cai@gmx.us Signed-off-by: Qian Cai <cai@gmx.us> Suggested-by: Thomas Gleixner <tglx@linutronix.de> Cc: Waiman Long <longman@redhat.com> Cc: Yang Shi <yang.shi@linux.alibaba.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update license to use SPDX-License-Identifier instead of verbose license
text, excepting ${LINUX}/arch/sh/kernel/cpu/sh4/softfloat.c which is not
GPL license
Link: http://lkml.kernel.org/r/87a7lkcsya.wl-kuninori.morimoto.gx@renesas.com Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Cc: Rich Felker <dalias@libc.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arch/sh/boards/mach-kfr2r09/setup.c does not need to #include
<mtd/onenand.h>, and doing so causes a build warning, so drop that header
file.
In file included from ../arch/sh/boards/mach-kfr2r09/setup.c:28:
../include/linux/mtd/onenand.h:225:12: warning: 'struct mtd_oob_ops' declared inside parameter list will not be visible outside of this definition or declaration
struct mtd_oob_ops *ops);
Link: http://lkml.kernel.org/r/702f0a25-c63e-6912-4640-6ab0f00afbc7@infradead.org Fixes: f3590dc32974 ("media: arch: sh: kfr2r09: Use new renesas-ceu camera driver") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Suggested-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Rich Felker <dalias@libc.org> Cc: Jacopo Mondi <jacopo+renesas@jmondi.org> Cc: Magnus Damm <magnus.damm@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thierry Reding [Fri, 28 Dec 2018 08:31:32 +0000 (00:31 -0800)]
scripts: add spdxcheck.py self test
Add a script that will run spdxcheck.py through a couple of self tests to
simplify validation in the future. The tests are run for both Python 2
and Python 3 to make sure all changes to the script remain compatible
across both versions.
The script tests a regular text file (Makefile) for basic sanity checks
and then runs it on a binary file (Documentation/logo.gif) to make sure it
works in both cases. It also tests opening files passed on the command
line as well as piped files read from standard input. Finally a run on
the complete tree will be performed to catch any other potential issues.
Link: http://lkml.kernel.org/r/20181212131210.28024-2-thierry.reding@gmail.com Signed-off-by: Thierry Reding <treding@nvidia.com>
Thomas Gleixner <tglx@linutronix.de> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Joe Perches <joe@perches.com> Cc: Jeremy Cline <jcline@redhat.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Qian Cai [Fri, 28 Dec 2018 08:31:28 +0000 (00:31 -0800)]
scripts/checkstack.pl: dynamic stack growth for aarch64
This is to track dynamic amount of stack growth for aarch64, so it is
possible to print out offensive functions that may consume too much stack.
For example,
Marc Zyngier [Fri, 28 Dec 2018 08:31:25 +0000 (00:31 -0800)]
scripts/decode_stacktrace: only strip base path when a prefix of the path
Running something like:
decodecode vmlinux .
leads to interested results where not only the leading "." gets stripped
from the displayed paths, but also anywhere in the string, displaying
something like:
Andrey Konovalov [Fri, 28 Dec 2018 08:30:57 +0000 (00:30 -0800)]
kasan, mm, arm64: tag non slab memory allocated via pagealloc
Tag-based KASAN doesn't check memory accesses through pointers tagged with
0xff. When page_address is used to get pointer to memory that corresponds
to some page, the tag of the resulting pointer gets set to 0xff, even
though the allocated memory might have been tagged differently.
For slab pages it's impossible to recover the correct tag to return from
page_address, since the page might contain multiple slab objects tagged
with different values, and we can't know in advance which one of them is
going to get accessed. For non slab pages however, we can recover the tag
in page_address, since the whole page was marked with the same tag.
This patch adds tagging to non slab memory allocated with pagealloc. To
set the tag of the pointer returned from page_address, the tag gets stored
to page->flags when the memory gets allocated.
Link: http://lkml.kernel.org/r/d758ddcef46a5abc9970182b9137e2fbee202a2c.1544099024.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by: Dmitry Vyukov <dvyukov@google.com> Acked-by: Will Deacon <will.deacon@arm.com> Cc: Christoph Lameter <cl@linux.com> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Fri, 28 Dec 2018 08:30:54 +0000 (00:30 -0800)]
kasan, arm64: add brk handler for inline instrumentation
Tag-based KASAN inline instrumentation mode (which embeds checks of shadow
memory into the generated code, instead of inserting a callback) generates
a brk instruction when a tag mismatch is detected.
This commit adds a tag-based KASAN specific brk handler, that decodes the
immediate value passed to the brk instructions (to extract information
about the memory access that triggered the mismatch), reads the register
values (x0 contains the guilty address) and reports the bug.
Link: http://lkml.kernel.org/r/c91fe7684070e34dc34b419e6b69498f4dcacc2d.1544099024.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by: Dmitry Vyukov <dvyukov@google.com> Acked-by: Will Deacon <will.deacon@arm.com> Cc: Christoph Lameter <cl@linux.com> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Fri, 28 Dec 2018 08:30:50 +0000 (00:30 -0800)]
kasan: add hooks implementation for tag-based mode
This commit adds tag-based KASAN specific hooks implementation and
adjusts common generic and tag-based KASAN ones.
1. When a new slab cache is created, tag-based KASAN rounds up the size of
the objects in this cache to KASAN_SHADOW_SCALE_SIZE (== 16).
2. On each kmalloc tag-based KASAN generates a random tag, sets the shadow
memory, that corresponds to this object to this tag, and embeds this
tag value into the top byte of the returned pointer.
3. On each kfree tag-based KASAN poisons the shadow memory with a random
tag to allow detection of use-after-free bugs.
The rest of the logic of the hook implementation is very much similar to
the one provided by generic KASAN. Tag-based KASAN saves allocation and
free stack metadata to the slab object the same way generic KASAN does.
Link: http://lkml.kernel.org/r/bda78069e3b8422039794050ddcb2d53d053ed41.1544099024.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by: Dmitry Vyukov <dvyukov@google.com> Cc: Christoph Lameter <cl@linux.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Fri, 28 Dec 2018 08:30:46 +0000 (00:30 -0800)]
mm: move obj_to_index to include/linux/slab_def.h
While with SLUB we can actually preassign tags for caches with contructors
and store them in pointers in the freelist, SLAB doesn't allow that since
the freelist is stored as an array of indexes, so there are no pointers to
store the tags.
Instead we compute the tag twice, once when a slab is created before
calling the constructor and then again each time when an object is
allocated with kmalloc. Tag is computed simply by taking the lowest byte
of the index that corresponds to the object. However in kasan_kmalloc we
only have access to the objects pointer, so we need a way to find out
which index this object corresponds to.
This patch moves obj_to_index from slab.c to include/linux/slab_def.h to
be reused by KASAN.
Link: http://lkml.kernel.org/r/c02cd9e574cfd93858e43ac94b05e38f891fef64.1544099024.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by: Dmitry Vyukov <dvyukov@google.com> Acked-by: Christoph Lameter <cl@linux.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Fri, 28 Dec 2018 08:30:42 +0000 (00:30 -0800)]
kasan: add bug reporting routines for tag-based mode
This commit adds rountines, that print tag-based KASAN error reports.
Those are quite similar to generic KASAN, the difference is:
1. The way tag-based KASAN finds the first bad shadow cell (with a
mismatching tag). Tag-based KASAN compares memory tags from the shadow
memory to the pointer tag.
2. Tag-based KASAN reports all bugs with the "KASAN: invalid-access"
header.
Also simplify generic KASAN find_first_bad_addr.
Link: http://lkml.kernel.org/r/aee6897b1bd077732a315fd84c6b4f234dbfdfcb.1544099024.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by: Dmitry Vyukov <dvyukov@google.com> Cc: Christoph Lameter <cl@linux.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Fri, 28 Dec 2018 08:30:38 +0000 (00:30 -0800)]
kasan: split out generic_report.c from report.c
Move generic KASAN specific error reporting routines to generic_report.c
without any functional changes, leaving common error reporting code in
report.c to be later reused by tag-based KASAN.
Link: http://lkml.kernel.org/r/ba48c32f8e5aefedee78998ccff0413bee9e0f5b.1544099024.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by: Dmitry Vyukov <dvyukov@google.com> Cc: Christoph Lameter <cl@linux.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Fri, 28 Dec 2018 08:30:35 +0000 (00:30 -0800)]
kasan, mm: perform untagged pointers comparison in krealloc
The krealloc function checks where the same buffer was reused or a new one
allocated by comparing kernel pointers. Tag-based KASAN changes memory
tag on the krealloc'ed chunk of memory and therefore also changes the
pointer tag of the returned pointer. Therefore we need to perform
comparison on untagged (with tags reset) pointers to check whether it's
the same memory region or not.
Link: http://lkml.kernel.org/r/14f6190d7846186a3506cd66d82446646fe65090.1544099024.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by: Dmitry Vyukov <dvyukov@google.com> Cc: Christoph Lameter <cl@linux.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Fri, 28 Dec 2018 08:30:31 +0000 (00:30 -0800)]
kasan, arm64: enable top byte ignore for the kernel
Tag-based KASAN uses the Top Byte Ignore feature of arm64 CPUs to store a
pointer tag in the top byte of each pointer. This commit enables the
TCR_TBI1 bit, which enables Top Byte Ignore for the kernel, when tag-based
KASAN is used.
Link: http://lkml.kernel.org/r/f51eca084c8cdb2f3a55195fe342dc8953b7aead.1544099024.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by: Dmitry Vyukov <dvyukov@google.com> Acked-by: Will Deacon <will.deacon@arm.com> Cc: Christoph Lameter <cl@linux.com> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Fri, 28 Dec 2018 08:30:27 +0000 (00:30 -0800)]
kasan, arm64: fix up fault handling logic
Right now arm64 fault handling code removes pointer tags from addresses
covered by TTBR0 in faults taken from both EL0 and EL1, but doesn't do
that for pointers covered by TTBR1.
This patch adds two helper functions is_ttbr0_addr() and is_ttbr1_addr(),
where the latter one accounts for the fact that TTBR1 pointers might be
tagged when tag-based KASAN is in use, and uses these helper functions to
perform pointer checks in arch/arm64/mm/fault.c.
Link: http://lkml.kernel.org/r/3f349b0e9e48b5df3298a6b4ae0634332274494a.1544099024.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Suggested-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Christoph Lameter <cl@linux.com> Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Fri, 28 Dec 2018 08:30:23 +0000 (00:30 -0800)]
kasan: preassign tags to objects with ctors or SLAB_TYPESAFE_BY_RCU
An object constructor can initialize pointers within this objects based on
the address of the object. Since the object address might be tagged, we
need to assign a tag before calling constructor.
The implemented approach is to assign tags to objects with constructors
when a slab is allocated and call constructors once as usual. The
downside is that such object would always have the same tag when it is
reallocated, so we won't catch use-after-frees on it.
Also pressign tags for objects from SLAB_TYPESAFE_BY_RCU caches, since
they can be validy accessed after having been freed.
Link: http://lkml.kernel.org/r/f158a8a74a031d66f0a9398a5b0ed453c37ba09a.1544099024.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by: Dmitry Vyukov <dvyukov@google.com> Cc: Christoph Lameter <cl@linux.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Fri, 28 Dec 2018 08:30:20 +0000 (00:30 -0800)]
kasan, arm64: untag address in _virt_addr_is_linear
virt_addr_is_linear (which is used by virt_addr_valid) assumes that the
top byte of the address is 0xff, which isn't always the case with
tag-based KASAN.
This patch resets the tag in this macro.
Link: http://lkml.kernel.org/r/df73a37dd5ed37f4deaf77bc718e9f2e590e69b1.1544099024.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by: Dmitry Vyukov <dvyukov@google.com> Acked-by: Will Deacon <will.deacon@arm.com> Cc: Christoph Lameter <cl@linux.com> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Fri, 28 Dec 2018 08:30:16 +0000 (00:30 -0800)]
kasan: add tag related helper functions
This commit adds a few helper functions, that are meant to be used to work
with tags embedded in the top byte of kernel pointers: to set, to get or
to reset the top byte.
Link: http://lkml.kernel.org/r/f6c6437bb8e143bc44f42c3c259c62e734be7935.1544099024.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Christoph Lameter <cl@linux.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Fri, 28 Dec 2018 08:30:12 +0000 (00:30 -0800)]
arm64: move untagged_addr macro from uaccess.h to memory.h
Move the untagged_addr() macro from arch/arm64/include/asm/uaccess.h
to arch/arm64/include/asm/memory.h to be later reused by KASAN.
Also make the untagged_addr() macro accept all kinds of address types
(void *, unsigned long, etc.). This allows not to specify type casts in
each place where the macro is used. This is done by using __typeof__.
Link: http://lkml.kernel.org/r/2e9ef8d2ed594106eca514b268365b5419113f6a.1544099024.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Christoph Lameter <cl@linux.com> Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Fri, 28 Dec 2018 08:30:09 +0000 (00:30 -0800)]
kasan: initialize shadow to 0xff for tag-based mode
A tag-based KASAN shadow memory cell contains a memory tag, that
corresponds to the tag in the top byte of the pointer, that points to that
memory. The native top byte value of kernel pointers is 0xff, so with
tag-based KASAN we need to initialize shadow memory to 0xff.
Andrey Konovalov [Fri, 28 Dec 2018 08:30:01 +0000 (00:30 -0800)]
kasan: rename kasan_zero_page to kasan_early_shadow_page
With tag based KASAN mode the early shadow value is 0xff and not 0x00, so
this patch renames kasan_zero_(page|pte|pmd|pud|p4d) to
kasan_early_shadow_(page|pte|pmd|pud|p4d) to avoid confusion.
Link: http://lkml.kernel.org/r/3fed313280ebf4f88645f5b89ccbc066d320e177.1544099024.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Suggested-by: Mark Rutland <mark.rutland@arm.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Christoph Lameter <cl@linux.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Fri, 28 Dec 2018 08:29:53 +0000 (00:29 -0800)]
kasan: add CONFIG_KASAN_GENERIC and CONFIG_KASAN_SW_TAGS
This commit splits the current CONFIG_KASAN config option into two:
1. CONFIG_KASAN_GENERIC, that enables the generic KASAN mode (the one
that exists now);
2. CONFIG_KASAN_SW_TAGS, that enables the software tag-based KASAN mode.
The name CONFIG_KASAN_SW_TAGS is chosen as in the future we will have
another hardware tag-based KASAN mode, that will rely on hardware memory
tagging support in arm64.
With CONFIG_KASAN_SW_TAGS enabled, compiler options are changed to
instrument kernel files with -fsantize=kernel-hwaddress (except the ones
for which KASAN_SANITIZE := n is set).
Both CONFIG_KASAN_GENERIC and CONFIG_KASAN_SW_TAGS support both
CONFIG_KASAN_INLINE and CONFIG_KASAN_OUTLINE instrumentation modes.
This commit also adds empty placeholder (for now) implementation of
tag-based KASAN specific hooks inserted by the compiler and adjusts
common hooks implementation.
While this commit adds the CONFIG_KASAN_SW_TAGS config option, this option
is not selectable, as it depends on HAVE_ARCH_KASAN_SW_TAGS, which we will
enable once all the infrastracture code has been added.
Link: http://lkml.kernel.org/r/b2550106eb8a68b10fefbabce820910b115aa853.1544099024.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by: Dmitry Vyukov <dvyukov@google.com> Cc: Christoph Lameter <cl@linux.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Fri, 28 Dec 2018 08:29:49 +0000 (00:29 -0800)]
kasan: rename source files to reflect the new naming scheme
We now have two KASAN modes: generic KASAN and tag-based KASAN. Rename
kasan.c to generic.c to reflect that. Also rename kasan_init.c to init.c
as it contains initialization code for both KASAN modes.
Link: http://lkml.kernel.org/r/88c6fd2a883e459e6242030497230e5fb0d44d44.1544099024.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by: Dmitry Vyukov <dvyukov@google.com> Cc: Christoph Lameter <cl@linux.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Fri, 28 Dec 2018 08:29:41 +0000 (00:29 -0800)]
kasan, slub: handle pointer tags in early_kmem_cache_node_alloc
The previous patch updated KASAN hooks signatures and their usage in SLAB
and SLUB code, except for the early_kmem_cache_node_alloc function. This
patch handles that function separately, as it requires to reorder some of
the initialization code to correctly propagate a tagged pointer in case a
tag is assigned by kasan_kmalloc.
Link: http://lkml.kernel.org/r/fc8d0fdcf733a7a52e8d0daaa650f4736a57de8c.1544099024.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Christoph Lameter <cl@linux.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Fri, 28 Dec 2018 08:29:37 +0000 (00:29 -0800)]
kasan, mm: change hooks signatures
Patch series "kasan: add software tag-based mode for arm64", v13.
This patchset adds a new software tag-based mode to KASAN [1]. (Initially
this mode was called KHWASAN, but it got renamed, see the naming rationale
at the end of this section).
The plan is to implement HWASan [2] for the kernel with the incentive,
that it's going to have comparable to KASAN performance, but in the same
time consume much less memory, trading that off for somewhat imprecise bug
detection and being supported only for arm64.
The underlying ideas of the approach used by software tag-based KASAN are:
1. By using the Top Byte Ignore (TBI) arm64 CPU feature, we can store
pointer tags in the top byte of each kernel pointer.
2. Using shadow memory, we can store memory tags for each chunk of kernel
memory.
3. On each memory allocation, we can generate a random tag, embed it into
the returned pointer and set the memory tags that correspond to this
chunk of memory to the same value.
4. By using compiler instrumentation, before each memory access we can add
a check that the pointer tag matches the tag of the memory that is being
accessed.
5. On a tag mismatch we report an error.
With this patchset the existing KASAN mode gets renamed to generic KASAN,
with the word "generic" meaning that the implementation can be supported
by any architecture as it is purely software.
The new mode this patchset adds is called software tag-based KASAN. The
word "tag-based" refers to the fact that this mode uses tags embedded into
the top byte of kernel pointers and the TBI arm64 CPU feature that allows
to dereference such pointers. The word "software" here means that shadow
memory manipulation and tag checking on pointer dereference is done in
software. As it is the only tag-based implementation right now, "software
tag-based" KASAN is sometimes referred to as simply "tag-based" in this
patchset.
A potential expansion of this mode is a hardware tag-based mode, which
would use hardware memory tagging support (announced by Arm [3]) instead
of compiler instrumentation and manual shadow memory manipulation.
Same as generic KASAN, software tag-based KASAN is strictly a debugging
feature.
On mobile devices generic KASAN's memory usage is significant problem.
One of the main reasons to have tag-based KASAN is to be able to perform a
similar set of checks as the generic one does, but with lower memory
requirements.
Comment from Vishwath Mohan <vishwath@google.com>:
I don't have data on-hand, but anecdotally both ASAN and KASAN have proven
problematic to enable for environments that don't tolerate the increased
memory pressure well. This includes
(a) Low-memory form factors - Wear, TV, Things, lower-tier phones like Go,
(c) Connected components like Pixel's visual core [1].
These are both places I'd love to have a low(er) memory footprint option at
my disposal.
Comment from Evgenii Stepanov <eugenis@google.com>:
Looking at a live Android device under load, slab (according to
/proc/meminfo) + kernel stack take 8-10% available RAM (~350MB). KASAN's
overhead of 2x - 3x on top of it is not insignificant.
Not having this overhead enables near-production use - ex. running
KASAN/KHWASAN kernel on a personal, daily-use device to catch bugs that do
not reproduce in test configuration. These are the ones that often cost
the most engineering time to track down.
CPU overhead is bad, but generally tolerable. RAM is critical, in our
experience. Once it gets low enough, OOM-killer makes your life
miserable.
Software tag-based KASAN mode is implemented in a very similar way to the
generic one. This patchset essentially does the following:
1. TCR_TBI1 is set to enable Top Byte Ignore.
2. Shadow memory is used (with a different scale, 1:16, so each shadow
byte corresponds to 16 bytes of kernel memory) to store memory tags.
3. All slab objects are aligned to shadow scale, which is 16 bytes.
4. All pointers returned from the slab allocator are tagged with a random
tag and the corresponding shadow memory is poisoned with the same value.
5. Compiler instrumentation is used to insert tag checks. Either by
calling callbacks or by inlining them (CONFIG_KASAN_OUTLINE and
CONFIG_KASAN_INLINE flags are reused).
6. When a tag mismatch is detected in callback instrumentation mode
KASAN simply prints a bug report. In case of inline instrumentation,
clang inserts a brk instruction, and KASAN has it's own brk handler,
which reports the bug.
7. The memory in between slab objects is marked with a reserved tag, and
acts as a redzone.
8. When a slab object is freed it's marked with a reserved tag.
Bug detection is imprecise for two reasons:
1. We won't catch some small out-of-bounds accesses, that fall into the
same shadow cell, as the last byte of a slab object.
2. We only have 1 byte to store tags, which means we have a 1/256
probability of a tag match for an incorrect access (actually even
slightly less due to reserved tag values).
Despite that there's a particular type of bugs that tag-based KASAN can
detect compared to generic KASAN: use-after-free after the object has been
allocated by someone else.
====== Testing
Some kernel developers voiced a concern that changing the top byte of
kernel pointers may lead to subtle bugs that are difficult to discover.
To address this concern deliberate testing has been performed.
It doesn't seem feasible to do some kind of static checking to find
potential issues with pointer tagging, so a dynamic approach was taken.
All pointer comparisons/subtractions have been instrumented in an LLVM
compiler pass and a kernel module that would print a bug report whenever
two pointers with different tags are being compared/subtracted (ignoring
comparisons with NULL pointers and with pointers obtained by casting an
error code to a pointer type) has been used. Then the kernel has been
booted in QEMU and on an Odroid C2 board and syzkaller has been run.
This yielded the following results.
The two places that look interesting are:
is_vmalloc_addr in include/linux/mm.h
is_kernel_rodata in mm/util.c
Here we compare a pointer with some fixed untagged values to make sure
that the pointer lies in a particular part of the kernel address space.
Since tag-based KASAN doesn't add tags to pointers that belong to rodata
or vmalloc regions, this should work as is. To make sure debug checks to
those two functions that check that the result doesn't change whether we
operate on pointers with or without untagging has been added.
A few other cases that don't look that interesting:
Comparing pointers to achieve unique sorting order of pointee objects
(e.g. sorting locks addresses before performing a double lock):
tty_ldisc_lock_pair_timeout in drivers/tty/tty_ldisc.c
pipe_double_lock in fs/pipe.c
unix_state_double_lock in net/unix/af_unix.c
lock_two_nondirectories in fs/inode.c
mutex_lock_double in kernel/events/core.c
ep_cmp_ffd in fs/eventpoll.c
fsnotify_compare_groups fs/notify/mark.c
Nothing needs to be done here, since the tags embedded into pointers
don't change, so the sorting order would still be unique.
Checks that a pointer belongs to some particular allocation:
is_sibling_entry in lib/radix-tree.c
object_is_on_stack in include/linux/sched/task_stack.h
Nothing needs to be done here either, since two pointers can only belong
to the same allocation if they have the same tag.
Overall, since the kernel boots and works, there are no critical bugs.
As for the rest, the traditional kernel testing way (use until fails) is
the only one that looks feasible.
Another point here is that tag-based KASAN is available under a separate
config option that needs to be deliberately enabled. Even though it might
be used in a "near-production" environment to find bugs that are not found
during fuzzing or running tests, it is still a debug tool.
====== Benchmarks
The following numbers were collected on Odroid C2 board. Both generic and
tag-based KASAN were used in inline instrumentation mode.
Boot time [1]:
* ~1.7 sec for clean kernel
* ~5.0 sec for generic KASAN
* ~5.0 sec for tag-based KASAN
Network performance [2]:
* 8.33 Gbits/sec for clean kernel
* 3.17 Gbits/sec for generic KASAN
* 2.85 Gbits/sec for tag-based KASAN
Slab memory usage after boot [3]:
* ~40 kb for clean kernel
* ~105 kb (~260% overhead) for generic KASAN
* ~47 kb (~20% overhead) for tag-based KASAN
KASAN memory overhead consists of three main parts:
1. Increased slab memory usage due to redzones.
2. Shadow memory (the whole reserved once during boot).
3. Quaratine (grows gradually until some preset limit; the more the limit,
the more the chance to detect a use-after-free).
Comparing tag-based vs generic KASAN for each of these points:
1. 20% vs 260% overhead.
2. 1/16th vs 1/8th of physical memory.
3. Tag-based KASAN doesn't require quarantine.
[1] Time before the ext4 driver is initialized.
[2] Measured as `iperf -s & iperf -c 127.0.0.1 -t 30`.
[3] Measured as `cat /proc/meminfo | grep Slab`.
====== Some notes
A few notes:
1. The patchset can be found here:
https://github.com/xairy/kasan-prototype/tree/khwasan
2. Building requires a recent Clang version (7.0.0 or later).
3. Stack instrumentation is not supported yet and will be added later.
This patch (of 25):
Tag-based KASAN changes the value of the top byte of pointers returned
from the kernel allocation functions (such as kmalloc). This patch
updates KASAN hooks signatures and their usage in SLAB and SLUB code to
reflect that.
Link: http://lkml.kernel.org/r/aec2b5e3973781ff8a6bb6760f8543643202c451.1544099024.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by: Dmitry Vyukov <dvyukov@google.com> Cc: Christoph Lameter <cl@linux.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 28 Dec 2018 01:12:30 +0000 (17:12 -0800)]
Merge tag 'locks-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux
Pull file locking updates from Jeff Layton:
"The main change in this set is Neil Brown's work to reduce the
thundering herd problem when a heavily-contended file lock is
released.
Previously we'd always wake up all waiters when this occurred. With
this set, we'll now we only wake up waiters that were blocked on the
range being released"
* tag 'locks-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
locks: Use inode_is_open_for_write
fs/locks: remove unnecessary white space.
fs/locks: merge posix_unblock_lock() and locks_delete_block()
fs/locks: create a tree of dependent requests.
fs/locks: change all *_conflict() functions to return bool.
fs/locks: always delete_block after waiting.
fs/locks: allow a lock request to block other requests.
fs/locks: use properly initialized file_lock when unlocking.
ocfs2: properly initial file_lock used for unlock.
gfs2: properly initial file_lock used for unlock.
NFS: use locks_copy_lock() to copy locks.
fs/locks: split out __locks_wake_up_blocks().
fs/locks: rename some lists and pointers.
Linus Torvalds [Fri, 28 Dec 2018 01:09:41 +0000 (17:09 -0800)]
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"All cleanups and bug fixes; most notably, fix some problems discovered
in ext4's NFS support, and fix an ioctl (EXT4_IOC_GROUP_ADD) used by
old versions of e2fsprogs which we accidentally broke a while back.
Also fixed some error paths in ext4's quota and inline data support.
Finally, improve tail latency in jbd2's commit code"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: check for shutdown and r/o file system in ext4_write_inode()
ext4: force inode writes when nfsd calls commit_metadata()
ext4: avoid declaring fs inconsistent due to invalid file handles
ext4: include terminating u32 in size of xattr entries when expanding inodes
ext4: compare old and new mode before setting update_mode flag
ext4: fix EXT4_IOC_GROUP_ADD ioctl
ext4: hard fail dax mount on unsupported devices
jbd2: update locking documentation for transaction_t
ext4: remove redundant condition check
jbd2: clean up indentation issue, replace spaces with tab
ext4: clean up indentation issues, remove extraneous tabs
ext4: missing unlock/put_page() in ext4_try_to_write_inline_data()
ext4: fix possible use after free in ext4_quota_enable
jbd2: avoid long hold times of j_state_lock while committing a transaction
ext4: add ext4_sb_bread() to disambiguate ENOMEM cases
Linus Torvalds [Fri, 28 Dec 2018 01:04:23 +0000 (17:04 -0800)]
Merge tag 'xfs-4.21-merge-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull XFS updates from Darrick Wong:
- Fix CoW remapping of extremely fragmented file areas
- Fix a zero-length symlink verifier error
- Constify some of the rmap owner structures for per-AG metadata
- Precalculate inode geometry for later use
- Fix scrub counting problems
- Don't crash when rtsummary inode is null
- Fix x32 ioctl operation
- Fix enum->string mappings for ftrace output
- Cache realtime summary information in memory
* tag 'xfs-4.21-merge-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: (24 commits)
xfs: reallocate realtime summary cache on growfs
xfs: stringify scrub types in ftrace output
xfs: stringify btree cursor types in ftrace output
xfs: move XFS_INODE_FORMAT_STR mappings to libxfs
xfs: move XFS_AG_BTREE_CMP_FORMAT_STR mappings to libxfs
xfs: fix symbolic enum printing in ftrace output
xfs: fix function pointer type in ftrace format
xfs: Fix x32 ioctls when cmd numbers differ from ia32.
xfs: Fix bulkstat compat ioctls on x32 userspace.
xfs: Align compat attrlist_by_handle with native implementation.
xfs: require both realtime inodes to mount
xfs: cache minimum realtime summary level
xfs: count inode blocks correctly in inobt scrub
xfs: precalculate cluster alignment in inodes and blocks
xfs: precalculate inodes and blocks per inode cluster
xfs: add a block to inode count converter
xfs: remove xfs_rmap_ag_owner and friends
xfs: const-ify xfs_owner_info arguments
xfs: streamline defer op type handling
xfs: idiotproof defer op type configuration
...
Linus Torvalds [Fri, 28 Dec 2018 01:00:35 +0000 (17:00 -0800)]
Merge tag 'fs_for_4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull ext2, udf, and quota update from Jan Kara:
"Some ext2 cleanups, a fix for UDF crash on corrupted media, and one
quota locking fix"
* tag 'fs_for_4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
quota: Lock s_umount in exclusive mode for Q_XQUOTA{ON,OFF} quotactls.
udf: Fix BUG on corrupted inode
ext2: change reusable parameter to true when calling mb_cache_entry_create()
ext2: remove redundant condition check
ext2: avoid unnecessary operation in ext2_error()
Linus Torvalds [Fri, 28 Dec 2018 00:55:37 +0000 (16:55 -0800)]
Merge tag 'fsnotify_for_v4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull fsnotify updates from Jan Kara:
"Support for new FAN_OPEN_EXEC event and couple of cleanups around
fsnotify"
* tag 'fsnotify_for_v4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fanotify: Use inode_is_open_for_write
fanotify: Make sure to check event_len when copying
fsnotify/fdinfo: include fdinfo.h for inotify_show_fdinfo()
fanotify: introduce new event mask FAN_OPEN_EXEC_PERM
fsnotify: refactor fsnotify_parent()/fsnotify() paired calls when event is on path
fanotify: introduce new event mask FAN_OPEN_EXEC
fanotify: return only user requested event types in event mask
projects / mirror_ubuntu-focal-kernel.git / log