mv643xx_eth: deal with unexpected ethernet header sizes
When the IP header doesn't start 14, 18, 22 or 26 bytes into the packet
(which are the only four cases that the hardware can deal with if asked
to do IP checksumming on transmit), invoke the software checksum helper
instead of letting the packet go out with a corrupt checksum inserted
into the packet in the wrong place.
We have to explicitly tell the hardware to include the pseudo-header
when doing receive checksumming, otherwise hardware checksumming will
fail for every received packet and we'll end up setting CHECKSUM_NONE
on every received packet.
While we're at it, when skb->ip_summed is set to CHECKSUM_UNNECESSARY
on received packets, skb->csum is supposed to be undefined, and thus
there is no need to set it.
mv643xx_eth: add support for chips without transmit bandwidth control
Add support for mv643xx_eth versions that have no transmit bandwidth
control registers at all, such as the ethernet block found in the
Marvell 88F6183 ARM SoC.
mv643xx_eth: avoid reading ->byte_cnt twice during receive processing
Currently, the receive processing reads ->byte_cnt twice (once to
update interface statistics and once to properly size the data area
of the received skb), but since receive descriptors live in uncached
memory, caching this value in a local variable saves one uncached
access, and increases routing performance a tiny little bit more.
mv643xx_eth: shrink default receive and transmit queue sizes
Since the size of the receive queue is directly related to the data
cache footprint of the driver (between refilling a receive ring entry
with a fresh skb and receiving a packet in that entry, queue_size - 1
other skbs will have been touched), shrink the default receive queue
size to a saner number of entries, as 400 is definite overkill for
almost all workloads.
While we are at it, trim the default transmit queue size a bit as well.
mv643xx_eth: replace array of skbs awaiting transmit completion with a queue
Get rid of the skb pointer array that we currently use for transmit
reclaim, and replace it with an skb queue, to which skbuffs are appended
when they are passed to the xmit function, and removed from the front
and freed when we do transmit queue reclaim and hit a descriptor with
the 'owned by device' bit clear and 'last descriptor' bit set.
mv643xx_eth: avoid dropping tx lock during transmit reclaim
By moving DMA unmapping during transmit reclaim back under the netif
tx lock, we avoid the situation where we read the DMA address and buffer
length from the descriptor under the lock and then not do anything with
that data after dropping the lock on platforms where the DMA unmapping
routines are all NOPs (which is the case on all ARM platforms that
mv643xx_eth is used on at least).
This saves two uncached reads, which makes a small but measurable
performance difference in routing benchmarks.
mv643xx_eth: switch to netif tx queue lock, get rid of private spinlock
Since our ->hard_start_xmit() method is already called under spinlock
protection (the netif tx queue lock), we can simply make that lock
cover the private transmit state (descriptor ring indexes et al.) as
well, which avoids having to use a private lock to protect that state.
Since this was the last user of the driver-private spinlock, it can
be killed off.
mv643xx_eth: move all work to the napi poll handler
Move link status handling, transmit reclaim and TX_END handling from
the interrupt handler to the napi poll handler. This allows switching
->lock over to a non-IRQ-safe lock and removes all explicit interrupt
disabling from the driver.
As all the infrastructure for multiple transmit queues already exists
in the driver, this patch is entirely trivial.
The individual transmit queues are still serialised by the driver's
per-port private spinlock, but that will disappear (i.e. be replaced
by the per-subqueue ->_xmit_lock) in a subsequent patch.
mv643xx_eth: delete unused and uninteresting interrupt source mask bits
Delete a couple of unused and uninteresting interrupt source mask bits:
- The receive resource underrun interrupt sources are uninteresting
because if we are in out-of-memory mode, we are already dealing with
the issue, and we don't need the hardware to remind us again that we
are out of memory.
- The LINK and PHY interrupt sources can be coalesced into one define,
since we always use them together.
- The transmit resource underrun interrupt source can be disabled since
we never activate the head descriptor of a paged skb until the
fragments are all activated, so transmit underrun during a packet
should never happen.
- The INT_EXT_TX_0 define is never used.
Currently, there are two different fields in the
mv643xx_eth_platform_data struct that together describe the PHY
address -- one field (phy_addr) has the address of the PHY, but if
that address is zero, a second field (force_phy_addr) needs to be
set to distinguish the actual address zero from a zero due to not
having filled in the PHY address explicitly (which should mean
'use the default PHY address').
If we are a bit smarter about the encoding of the phy_addr field,
we can avoid the need for a second field -- this patch does that.
mv643xx_eth: smi sharing is a per-unit property, not a per-port one
Which top-level unit's SMI interface to use should be a property of
the top-level unit, not of the individual ports. This patch moves the
->shared_smi pointer from the per-port platform data to the global
platform data.
mv643xx_eth: get rid of compile-time configurable transmit checksumming
Get rid of the mv643xx_eth-internal MV643XX_ETH_CHECKSUM_OFFLOAD_TX
compile-time option. Using transmit checksumming is the sane default,
and anyone wanting to disable it should use ethtool(8) instead of
recompiling their kernels.
By having the receive out-of-memory handling timer schedule the napi
poll handler and then doing oom processing from the napi poll handler,
all code that touches receive state moves to napi context, letting us
get rid of all explicit locking in the receive paths since the only
mutual exclusion we need anymore at that point is protection against
reentering ourselves, which is provided by napi synchronisation.
mv643xx_eth: use the SMI done interrupt to wait for SMI access completion
If the platform code has passed us the IRQ number of the mv643xx_eth
top-level error interrupt, use the error interrupt to wait for SMI
access completion instead of polling the SMI busy bit, since SMI bus
accesses can take up to tens of milliseconds.
mv643xx_eth: switch ->phy_lock from a spinlock to a mutex
Since commit 81600eea98789da09a32de69ca9d3be8b9503c54 ("mv643xx_eth:
use auto phy polling for configuring (R)(G)MII interface"),
mv643xx_eth no longer does SMI accesses from interrupt context. The
only other callers that do SMI accesses all do them from process
context, which means we can switch the PHY lock from a spinlock to a
mutex, and get rid of the extra locking in some ethtool methods.
When tearing down a DMA mapping for a receive buffer, we should pass
dma_unmap_single() the exact same address that dma_map_single() gave
us when we originally set up the mapping.
Linus Torvalds [Thu, 28 Aug 2008 19:34:01 +0000 (12:34 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin arch: Fix PM building on BF52x: No ROTWE on BF52x, add USBWE
Blackfin arch: sram: use 'unsigned long' for irqflags
Blackfin arch: let PCI depend on BROKEN
Blackfin arch: move include/asm-blackfin header files to arch/blackfin
Blackfin arch: fix bug - MPU crashes under stress
Blackfin arch: Fix bug - when to rmmod the L1_module, it stucks and then reboot the board.
Blackfin arch: dont actually need to muck with EMAC_SYSTAT for BF52x for demuxing
Blackfin arch: Add MTD Partitions for MTD_DATAFLASH, increase max SPI SCLK
In accordance with commit f42ac38c59e0a03d6da0c24a63fb211393f484b0
("ftrace: disable tracing for suspend to ram"), disable tracing
around the suspend code in hibernation code paths.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Zijlstra [Tue, 19 Aug 2008 10:33:03 +0000 (12:33 +0200)]
sched: rt-bandwidth accounting fix
It fixes an accounting bug where we would continue accumulating runtime
even though the bandwidth control is disabled. This would lead to very long
throttle periods once bandwidth control gets turned on again.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Vegard Nossum [Thu, 28 Aug 2008 09:28:46 +0000 (17:28 +0800)]
Blackfin arch: sram: use 'unsigned long' for irqflags
Using just 'unsigned' will make flags an unsigned int. While this is
arguably not an error on blackfin where sizeof(int) == sizeof(long),
the patch is still justified on the grounds of principle.
The patch was generated using the Coccinelle semantic patch framework.
Cc: Julia Lawall <julia@diku.dk> Cc: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com> Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
John Blackwood [Tue, 26 Aug 2008 19:09:43 +0000 (15:09 -0400)]
sched: fix sched_rt_rq_enqueue() resched idle
When sysctl_sched_rt_runtime is set to something other than -1 and the
CONFIG_RT_GROUP_SCHED kernel parameter is NOT enabled, we get into a state
where we see one or more CPUs idling forvever even though there are
real-time
tasks in their rt runqueue that are able to run (no longer throttled).
The sequence is:
- A real-time task is running when the timer sets the rt runqueue
to throttled, and the rt task is resched_task()ed and switched
out, and idle is switched in since there are no non-rt tasks to
run on that cpu.
- Eventually the do_sched_rt_period_timer() runs and un-throttles
the rt runqueue, but we just exit the timer interrupt and go back
to executing the idle task in the idle loop forever.
If we change the sched_rt_rq_enqueue() routine to use some of the code
from the CONFIG_RT_GROUP_SCHED enabled version of this same routine and
resched_task() the currently executing task (idle in our case) if it is
a lower priority task than the higher rt task in the now un-throttled
runqueue, the problem is no longer observed.
Signed-off-by: John Blackwood <john.blackwood@ccur.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jean Delvare [Thu, 28 Aug 2008 06:33:23 +0000 (08:33 +0200)]
i2c: Prevent log spam on some DVB adapters
Some DVB adapters do not support the special I2C transaction that we
use for probing purposes. There's no point in logging this event, as
there's nothing the user can do and in general there is no actual
problem. So, degrade one of these messages to a debug message, and
move the other one around so that it is only printed on bogus drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Uwe Bugla <uwe.bugla@gmx.de>
Vlad Yasevich [Wed, 27 Aug 2008 23:09:49 +0000 (16:09 -0700)]
sctp: fix random memory dereference with SCTP_HMAC_IDENT option.
The number of identifiers needs to be checked against the option
length. Also, the identifier index provided needs to be verified
to make sure that it doesn't exceed the bounds of the array.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
IB/mlx4: Actually return L_Key and R_Key for fast register MRs
Initialize the L_Key and R_Key for memory regions returned from
mlx4_ib_alloc_fast_reg_mr(). Otherwise callers just get garbage for
the memory keys and can't do anything useful with these MRs.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 26 Aug 2008 18:55:58 +0000 (19:55 +0100)]
tty: Fix termios tty window resize race with pty/tty pair
Kanru Chen posted a patch versus the old code which deals with the case
where you resize the pty side of a pty/tty pair. In that situation the
termios data is updated for both pty and tty but the locks are not held
for the right side.
This implements the fix differently against the updated tty code. Patch
by self but the hard bit (noticing and fixing the bug) is thanks to Kanru
Chen.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 27 Aug 2008 21:31:44 +0000 (14:31 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
[PATCH] deal with the first call of ->show() generating no output
[PATCH] fix ->llseek() for a bunch of directories
[PATCH] fix regular readdir() and friends
[PATCH] fix hpux_getdents()
[PATCH] fix osf_getdirents()
[PATCH] ntfs: use d_add_ci
[PATCH] change d_add_ci argument ordering
[PATCH] fix efs_lookup()
[PATCH] proc: inode number fixlet
Linus Torvalds [Wed, 27 Aug 2008 21:28:45 +0000 (14:28 -0700)]
Merge branch 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: don't set the signal blocker on the master process.
drm: don't call the vblank tasklet with irqs disabled.
r300: Fix cliprect emit
drm/radeon: r300_cmdbuf: Always emit INDX_BUFFER immediately after DRAW_INDEX
radeon: fix some hard lockups on r3/4/500s
Jeff Layton [Wed, 27 Aug 2008 17:53:30 +0000 (17:53 +0000)]
[CIFS] Add destroy routine for dns_resolver
Otherwise, we're leaking the payload memory.
CC: Stable Kernel <stable@vger.kernel.org> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Linus Torvalds [Wed, 27 Aug 2008 08:14:46 +0000 (01:14 -0700)]
e1000: fix stack size
Here's the patch. It shrinks the stack from 1152 bytes to 192 bytes (the
first version, that only did the e1000_option part, got it down to 600
bytes). About half comes from not using multiple "e1000_option"
structures, the other half comes from turning the "e1000_opt_list[]"
arrays into "static const" instead, so that gcc doesn't copy them onto the
stack.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Reveiewed-by: Auke Kok <auke-jan.h.kok@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 27 Aug 2008 20:55:35 +0000 (13:55 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: remove blk_queue_tag_depth() and blk_queue_tag_queue()
block: remove unused ->busy part of the block queue tag map
bio: fix __bio_copy_iov() handling of bio->bv_len
bio: fix bio_copy_kern() handling of bio->bv_len
block: submit_bh() inadvertently discards barrier flag on a sync write
block: clean up cmdfilter sysfs interface
block: rename blk_scsi_cmd_filter to blk_cmd_filter
sg: restore command permission for TYPE_SCANNER
block: move cmdfilter from gendisk to request_queue
Linus Torvalds [Wed, 27 Aug 2008 20:54:55 +0000 (13:54 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: Increment the reference count of an already-active stack.
[PATCH] configfs: Consolidate locking around configfs_detach_prep() in configfs_rmdir()
ocfs2: correctly set i_blocks after inline dir gets expanded
ocfs2: Jump to correct label in ocfs2_expand_inline_dir()
ocfs2: Fix sleep-with-spinlock recovery regression
[PATCH] ocfs2/cluster/netdebug.c: fix warning
[PATCH] ocfs2/cluster/tcp.c: make some functions static
Steven Rostedt [Wed, 27 Aug 2008 13:14:40 +0000 (09:14 -0400)]
ftrace: disable tracing for suspend to ram
I've been painstakingly debugging the issue with suspend to ram and
ftraced. The 2.6.28 code does not have this issue, but since the mcount
recording is not going to be in 27, this must be solved for the ftrace
daemon version.
The resume from suspend to ram would reboot because it was triple
faulting. Debugging further, I found that calling the mcount function
itself was not an issue, but it would fault when it incremented
preempt_count. preempt_count is on the tasks info structure that is on the
low memory address of the task's stack. For some reason, it could not
write to it. Resuming out of suspend to ram does quite a lot of funny
tricks to get to work, so it is not surprising at all that simply doing a
preempt_disable() would cause a fault.
Thanks to Rafael for suggesting to add a "while (1);" to find the place in
resuming that is causing the fault. I would place the loop somewhere in
the code, compile and reboot and see if it would either reboot (hit the
fault) or simply hang (hit the loop). Doing this over and over again, I
narrowed it down that it was happening in enable_nonboot_cpus.
At this point, I found that it is easier to simply disable tracing around
the suspend code, instead of searching for the particular function that
can not handle doing a preempt_disable.
This patch disables the tracer as it suspends and reenables it on resume.
I tested this patch on my Laptop, and it can resume fine with the patch.
Signed-off-by: Steven Rostedt <srostedt@redhat.com> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In particular, the "struct file *" and the "struct inode *" arguments do
not necessarily match, which means that the unlocked version of the
ioctl (that only gets a "struct file *") isn't actually able to handle
the cases it needs to handle.
This fixes bugzilla
http://bugzilla.kernel.org/show_bug.cgi?id=11401
Reported-and-bisected-by: Laurent Riffard <laurent.riffard@free.fr> Acked-by: Peter Osterlund <petero2@telia.com> Cc: Alan Cox <alan@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Thu, 14 Aug 2008 10:10:14 +0000 (11:10 +0100)]
[ARM] Skip memory holes in FLATMEM when reading /proc/pagetypeinfo
Ordinarily, memory holes in flatmem still have a valid memmap and is safe
to use. However, an architecture (ARM) frees up the memmap backing memory
holes on the assumption it is never used. /proc/pagetypeinfo reads the
whole range of pages in a zone believing that the memmap is valid and that
pfn_valid will return false if it is not. On ARM, freeing the memmap breaks
the page->zone linkages even though pfn_valid() returns true and the kernel
can oops shortly afterwards due to accessing a bogus struct zone *.
This patch lets architectures say when FLATMEM can have holes in the
memmap. Rather than an expensive check for valid memory, /proc/pagetypeinfo
will confirm that the page linkages are still valid by checking page->zone
is still the expected zone. The lookup of page_zone is safe as there is a
limited range of memory that is accessed when calling page_zone. Even if
page_zone happens to return the correct zone, the impact is that the counters
in /proc/pagetypeinfo are slightly off but fragmentation monitoring is
unlikely to be relevant on an embedded system.
Reported-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Mel Gorman <mel@csn.ul.ie> Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dirk Behme [Sat, 15 Dec 2007 06:47:46 +0000 (07:47 +0100)]
[ARM] OMAP: Change mailing list for OMAP in MAINTAINERS
OMAP has now a list at vger.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ayaz Abdulla [Wed, 20 Aug 2008 23:34:37 +0000 (16:34 -0700)]
forcedeth: fix checksum flag
Fix the checksum feature advertised in device flags. The hardware support
TCP/UDP over IPv4 and TCP/UDP over IPv6 (without IPv6 extension headers).
However, the kernel feature flags do not distinguish IPv6 with/without
extension headers.
Therefore, the driver needs to use NETIF_F_IP_CSUM instead of
NETIF_F_HW_CSUM since the latter includes all IPv6 packets.
A future patch can be created to check for extension headers and perform
software checksum calculation.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com> Cc: Jeff Garzik <jgarzik@pobox.com> Cc: Manfred Spraul <manfred@colorfullife.com Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Oliver Martin [Sat, 23 Aug 2008 20:08:47 +0000 (22:08 +0200)]
net/usb/mcs7830: add set_mac_address
Implement set_mac_address for mcs7830. This enables me to use it with my
cable modem.
Signed-off-by: Oliver Martin <oliver.martin@student.tuwien.ac.at> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Arnd Bergmann [Sat, 23 Aug 2008 20:02:23 +0000 (22:02 +0200)]
net/usb/mcs7830: new device IDs
This adds USB device IDs for MosChip 7730 and Sitecom LN030
to the mcs7830 driver. The IDs have been reported to work without
further modifications.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: David Brownell <david-b@pacbell.net> Cc: Viktor Horvath <ViktorHorvath@gmx.net> Cc: Robbert Wethmar <robbert@wethmar.nl> Cc: Bart van der Klip <bklip@xs4all.nl> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Santiago Leon [Wed, 20 Aug 2008 19:09:19 +0000 (13:09 -0600)]
ibmveth: fix bad UDP checksums
This patch fixes a ibmveth bug where bad UDP checksums are being transmitted
when checksum offloading is enabled.
The hypervisor does checksum offloading only on TCP packets, so ibmveth calls
skb_checksum_help() for any other protocol. The bug happens because
the packet is being modified after the DMA map, so we would need a memory
barrier before making the hypervisor call. Reordering the code so that the
DMA map happens after skb_checksum_help() has the additional advantage of
fixing a DMA map leak if skb_checksum_help() where to fail.
Signed-off-by: Santiago Leon <santil@us.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alexander Duyck [Fri, 8 Aug 2008 23:51:26 +0000 (16:51 -0700)]
igb: remove 82576 quad adapter
Disable support for device 8086:10E8. Currently the result of loading the
driver with the device present causes system instability.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Takashi Iwai [Wed, 20 Aug 2008 23:34:35 +0000 (16:34 -0700)]
drivers/net/skfp/ess.c: fix compile warnings
CC [M] drivers/net/skfp/ess.o
drivers/net/skfp/ess.c: In function 'ess_send_response':
drivers/net/skfp/ess.c:513: warning: cast from pointer to integer of different size
drivers/net/skfp/ess.c: In function 'ess_send_alc_req':
drivers/net/skfp/ess.c:609: warning: cast from pointer to integer of different size
drivers/net/skfp/ess.c:639: warning: cast from pointer to integer of different size
Signed-off-by: Takashi Iwai <tiwai@suse.de> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Philip Love [Wed, 27 Aug 2008 09:33:50 +0000 (02:33 -0700)]
tcp: fix tcp header size miscalculation when window scale is unused
The size of the TCP header is miscalculated when the window scale ends
up being 0. Additionally, this can be induced by sending a SYN to a
passive open port with a window scale option with value 0.
Signed-off-by: Philip Love <love_phil@emc.com> Signed-off-by: Adam Langley <agl@imperialviolet.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Wed, 27 Aug 2008 09:27:10 +0000 (02:27 -0700)]
pkt_sched: Fix sch_tree_lock()
Use new qdisc_root_sleeping_lock() instead of qdisc_root_lock() as
sch_tree_lock() because this lock could be used while dev is
deactivated, but we never need to use this with noop_qdisc as a root.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Wed, 27 Aug 2008 09:25:17 +0000 (02:25 -0700)]
pkt_sched: Fix gen_estimator locks
While passing a qdisc root lock to gen_new_estimator() and
gen_replace_estimator() dev could be deactivated or even before
grafting proper root qdisc as qdisc_sleeping (e.g. qdisc_create), so
using qdisc_root_lock() is not enough. This patch adds
qdisc_root_sleeping_lock() for this, plus additional checks, where
necessary.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Klaus-D. Wacker [Thu, 21 Aug 2008 15:10:25 +0000 (17:10 +0200)]
LCS recovery dumps when cable reconnect
LCS recovery dumps in irq routine when CCW address in
Subchannel Status Word (SCSW) is zero. This occurs
when recovery is driven after cable reconnect.
probe_error() frees memory only, if cgdev->dev.driver_data refers
to the claw_privbk structure. Move forward its setting in claw_probe()
to ensure proper freeing of claw_privbk allocations.
Cc: Daniel <danielm77@spray.se> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alexander Duyck [Tue, 26 Aug 2008 11:25:13 +0000 (04:25 -0700)]
igb: fix setting the number of tx queues
The real_num_tx_queues was not being set when in MSI-X only mode. This patch
corrects that path so all interrupt types are correctly configured.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alexander Duyck [Tue, 26 Aug 2008 11:25:05 +0000 (04:25 -0700)]
igb: ethtool -d reads EICR which is incorrect as it is read on clear
Ethtool -d is reading the EICR and ICR registers which is currently
clearing these registers and masking off interrupts. To prevent this we
read the EICS and ICS equivilents as they can be read without clearing or
masking.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
projects / mirror_ubuntu-kernels.git / log