Michael Ellerman [Thu, 19 Oct 2017 04:08:43 +0000 (15:08 +1100)]
powerpc/64s: Replace CONFIG_PPC_STD_MMU_64 with CONFIG_PPC_BOOK3S_64
CONFIG_PPC_STD_MMU_64 indicates support for the "standard" powerpc MMU
on 64-bit CPUs. The "standard" MMU refers to the hash page table MMU
found in "server" processors, from IBM mainly.
Currently CONFIG_PPC_STD_MMU_64 is == CONFIG_PPC_BOOK3S_64. While it's
annoying to have two symbols that always have the same value, it's not
quite annoying enough to bother removing one.
However with the arrival of Power9, we now have the situation where
CONFIG_PPC_STD_MMU_64 is enabled, but the kernel is running using the
Radix MMU - *not* the "standard" MMU. So it is now actively confusing
to use it, because it implies that code is disabled or inactive when
the Radix MMU is in use, however that is not necessarily true.
So s/CONFIG_PPC_STD_MMU_64/CONFIG_PPC_BOOK3S_64/, and do some minor
formatting updates of some of the affected lines.
This will be a pain for backports, but c'est la vie.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Thu, 19 Oct 2017 04:08:19 +0000 (15:08 +1100)]
powerpc/64: Free up CPU_FTR_ICSWX
The last user of CPU_FTR_ICSWX was removed in commit 6ff4d3e96652 ("powerpc: Remove old unused icswx based coprocessor
support"), so free the bit up for future use.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/powernv: Reserve a hole which appears after enabling IOV
In order to make generic IOV code work, the physical function IOV BAR
should start from offset of the first VF. Since M64 segments share
PE number space across PHB, and some PEs may be in use at the time
when IOV is enabled, the existing code shifts the IOV BAR to the index
of the first PE/VF. This creates a hole in IOMEM space which can be
potentially taken by some other device.
This reserves a temporary hole on a parent and releases it when IOV is
disabled; the temporary resources are stored in pci_dn to avoid
kmalloc/free.
powerpc/pseries/vio: Dispose of virq mapping on vdevice unregister
When a vdevice is DLPAR removed from the system the vio subsystem
doesn't bother unmapping the virq from the irq_domain. As a result we
have a virq mapped to a hardware irq that is no longer valid for the
irq_domain. A side effect is that we are left with /proc/irq/<irq#>
affinity entries, and attempts to modify the smp_affinity of the irq
will fail.
In the following observed example the kernel log is spammed by
ics_rtas_set_affinity errors after the removal of a VSCSI adapter.
This is a result of irqbalance trying to adjust the affinity every 10
seconds.
This patch fixes the issue by calling irq_dispose_mapping() on the
virq of the viodev on unregister.
Fixes: f2ab6219969f ("powerpc/pseries: Add PFO support to the VIO bus") Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Tue, 24 Oct 2017 13:06:54 +0000 (23:06 +1000)]
powerpc/64s/radix: Fix process table entry cache invalidation
According to the architecture, the process table entry cache must be
flushed with tlbie RIC=2.
Currently the process table entry is set to invalid right before the
PID is returned to the allocator, with no invalidation. This works on
existing implementations that are known to not cache the process table
entry for any except the current PIDR.
It is architecturally correct and cleaner to invalidate with RIC=2
after clearing the process table entry and before the PID is returned
to the allocator. This can be done in arch_exit_mmap that runs before
the final flush, and to ensure the final flush (fullmm) is always a
RIC=2 variant.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Sat, 21 Oct 2017 07:56:06 +0000 (17:56 +1000)]
powerpc/64: Fix latency tracing for lazy irq replay
When returning from an exception to a soft-enabled context, pending
IRQs are replayed but IRQ tracing is not reset, so a number of them
can get chained together into the same IRQ-disabled trace.
Fix this by having __check_irq_replay re-set IRQ trace. This is
conceptually where we respond to the next interrupt, so it fits the
semantics of the IRQ tracer.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Markus Elfring [Wed, 18 Oct 2017 18:48:52 +0000 (20:48 +0200)]
powerpc/pseries: Cleanup error handling in iommu_pseries_alloc_group()
Although kfree(NULL) is legal, it's a bit lazy to rely on that to
implement the error handling. So do it the normal Linux way using
labels for each failure path.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[mpe: Squash a few patches and rewrite change log] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/perf/hv-24x7: Fix incorrect comparison in memord
In the hv-24x7 code there is a function memord() which tries to
implement a sort function return -1, 0, 1. However one of the
conditions is incorrect, such that it can never be true, because we
will have already returned.
I don't believe there is a bug in practice though, because the
comparisons are an optimisation prior to calling memcmp().
Fix it by swapping the second comparision, so it can be true.
Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc: Disable the fast-endian switch syscall by default
Back in 2008 we added support for "fast little-endian switch" in the
syscall path. This added a special case syscall number 0x1ebe, which
is caught very early in the system call exception and switches endian
with as little overhead as possible. See commit 745a14cc264b
("[POWERPC] Add fast little-endian switch system call") for full
details.
Although it is fast, it's also completely non standard. The "syscall
number" is out of the range of normal syscalls, it can't be traced or
audited, and it's a bit of a wart. To the best of our knowledge it was
only used by one program, now long since discontinued.
So in an effort to shake out any current users, put it behind a config
option, and make it default n. If anyone *is* using it they can
quickly reinstate it with a rebuild, and we can flip it to default y.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When dumping the paca in xmon we currently show kstack. Although it's
not hard it's a bit fiddly to work out what the bounds of the kernel
stack should be based on the kstack value.
To make life easier and "kstack_base" which is the base (lowest
address) of the kernel stack, eg:
Michael Ellerman [Mon, 16 Oct 2017 07:11:00 +0000 (12:41 +0530)]
powerpc/mm/radix: Drop unneeded NULL check
We call these functions with non-NULL mm or vma. Hence we can skip the
NULL check in these functions. We also remove now unused function
__local_flush_hugetlb_page().
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Drop the checks with is_vm_hugetlb_page() as noticed by Nick] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Breno Leitao [Tue, 17 Oct 2017 18:20:18 +0000 (16:20 -0200)]
powerpc/xmon: Check before calling xive functions
Currently xmon could call XIVE functions from OPAL even if the XIVE is
disabled or does not exist in the system, as in POWER8 machines. This
causes the following exception:
cxl: Provide debugfs access to PSL_DEBUG/XSL_DEBUG registers
Access to PSL/XSL_DEBUG registers on the adapter provides easy access
to the debug facilities provided by PSL/XSL. So this patch adds two
new files (debug, xsl-debug) to the cxl-adapter specific debugfs
folder located at /sys/kernel/debugfs/cxl/card<n>, which will provide
direct r/w access to corrosponding debug registers in the adapter
config-space.
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com> Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Unfortunately userspace can construct a sigcontext which enables
suspend. Thus userspace can force Linux into a path where trechkpt is
executed.
This patch blocks this from happening on POWER9 by sanity checking
sigcontexts passed in.
ptrace doesn't have this problem as only MSR SE and BE can be changed
via ptrace.
This patch also adds a number of WARN_ON()s in case we ever enter
suspend when we shouldn't. This should not happen, but if it does the
symptoms are soft lockup warnings which are not obviously TM related,
so the WARN_ON()s should make it obvious what's happening.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Cyril Bur <cyrilbur@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Thu, 12 Oct 2017 10:17:18 +0000 (21:17 +1100)]
powerpc/powernv: Enable TM without suspend if possible
Some Power9 revisions can run in a mode where TM operates without
suspended state. If we find ourself on a CPU that might be in this
mode, we query OPAL to check, and if so we reenable TM in CPU
features, and enable a new user feature to signal to userspace that we
are in this mode.
We do not enable the "normal" user feature, PPC_FEATURE2_HTM, but we
do enable PPC_FEATURE2_HTM_NOSC because that indicates to userspace
that the kernel will abort transactions on syscall entry, which is
true regardless of the suspend mode.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Thu, 12 Oct 2017 10:17:17 +0000 (21:17 +1100)]
powerpc: Add PPC_FEATURE2_HTM_NO_SUSPEND
Some CPUs can operate in a mode where TM (Transactional Memory) is
enabled but the suspended state of TM is disabled. In this mode
tsuspend does not enter suspended state, instead the transaction is
aborted. Similarly any other event that would lead to suspended state
instead aborts the transaction.
There is also an ABI change, in that in this mode processes are not
allowed to sigreturn with an MSR that would lead to suspended state,
Linux will instead return an error to the sigreturn syscall.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Cyril Bur [Thu, 12 Oct 2017 10:17:16 +0000 (21:17 +1100)]
powerpc/tm: Add commandline option to disable hardware transactional memory
Currently the kernel relies on firmware to inform it whether or not the
CPU supports HTM and as long as the kernel was built with
CONFIG_PPC_TRANSACTIONAL_MEM=y then it will allow userspace to make
use of the facility.
There may be situations where it would be advantageous for the kernel
to not allow userspace to use HTM, currently the only way to achieve
this is to recompile the kernel with CONFIG_PPC_TRANSACTIONAL_MEM=n.
This patch adds a simple commandline option so that HTM can be
disabled at boot time.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
[mpe: Simplify to a bool, move to prom.c, put doco in the right place.
Always disable, regardless of initial state, to avoid user confusion.] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Thu, 12 Oct 2017 11:58:54 +0000 (22:58 +1100)]
KVM: PPC: Tie KVM_CAP_PPC_HTM to the user-visible TM feature
Currently we use CPU_FTR_TM to decide if the CPU/kernel can support
TM (Transactional Memory), and if it's true we advertise that to
Qemu (or similar) via KVM_CAP_PPC_HTM.
PPC_FEATURE2_HTM is the user-visible feature bit, which indicates that
the CPU and kernel can support TM. Currently CPU_FTR_TM and
PPC_FEATURE2_HTM always have the same value, either true or false, so
using the former for KVM_CAP_PPC_HTM is correct.
However some Power9 CPUs can operate in a mode where TM is enabled but
TM suspended state is disabled. In this mode CPU_FTR_TM is true, but
PPC_FEATURE2_HTM is false. Instead a different PPC_FEATURE2 bit is
set, to indicate that this different mode of TM is available.
It is not safe to let guests use TM as-is, when the CPU is in this
mode. So to prevent that from happening, use PPC_FEATURE2_HTM to
determine the value of KVM_CAP_PPC_HTM.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In order to run HPT guests on a radix POWER9 host, we will have to run
the host in single-threaded mode, because POWER9 processors do not
currently support running some threads of a core in HPT mode while
others are in radix mode ("mixed mode").
That means that we will need the same mechanisms that are used on
POWER8 to make the secondary threads available to KVM, which were
disabled on POWER9 by commit 94a04bc25a2c.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/vphn: On Power systems with shared configurations of CPUs
and memory, there are some issues with the association of additional
CPUs and memory to nodes when hot-adding resources. This patch
fixes an end-of-updates processing problem observed occasionally
in numa_update_cpu_topology().
Signed-off-by: Michael Bringmann <mwb@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/hotplug: Improve responsiveness of hotplug change
powerpc/hotplug: On Power systems with shared configurations of CPUs
and memory, there are some issues with the association of additional
CPUs and memory to nodes when hot-adding resources. During hotplug
CPU operations, this patch resets the timer on topology update work
function to a small value to better ensure that the CPU topology is
detected and configured sooner.
Signed-off-by: Michael Bringmann <mwb@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/vphn: On Power systems with shared configurations of CPUs
and memory, there are some issues with the association of additional
CPUs and memory to nodes when hot-adding resources. This patch
updates the initialization checks to independently recognize PRRN
or VPHN support.
Signed-off-by: Michael Bringmann <mwb@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/vphn: Update CPU topology when VPHN enabled
powerpc/vphn: On Power systems with shared configurations of CPUs
and memory, there are some issues with the association of additional
CPUs and memory to nodes when hot-adding resources. This patch
corrects the currently broken capability to set the topology for
shared CPUs in LPARs. At boot time for shared CPU lpars, the
topology for each CPU was being set to node zero. Now when
numa_update_cpu_topology() is called appropriately, the Virtual
Processor Home Node (VPHN) capabilities information provided by the
pHyp allows the appropriate node in the shared configuration to be
selected for the CPU.
Signed-off-by: Michael Bringmann <mwb@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If we are in user space and hit a UE error, we now have the
basic infrastructure to walk the page tables and find out
the effective address that was accessed, since the DAR
is not valid.
We use a work_queue content to hookup the bad pfn, any
other context causes problems, since memory_failure itself
can call into schedule() via lru_drain_ bits.
We could probably poison the struct page to avoid a race
between detection and taking corrective action.
Signed-off-by: Balbir Singh <bsingharora@gmail.com> Reviewed-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Hookup instruction errors (UE) for memory offling via memory_failure()
in a manner similar to load/store errors (derror). Since we have access
to the NIP, the conversion is a one step process in this case.
Signed-off-by: Balbir Singh <bsingharora@gmail.com> Reviewed-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Extract physical_address for UE errors by walking the page
tables for the mm and address at the NIP, to extract the
instruction. Then use the instruction to find the effective
address via analyse_instr().
We might have page table walking races, but we expect them to
be rare, the physical address extraction is best effort. The idea
is to then hook up this infrastructure to memory failure eventually.
Signed-off-by: Balbir Singh <bsingharora@gmail.com> Reviewed-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mce: Remove unused function get_mce_fault_addr()
There are no users of get_mce_fault_addr() since commit 1363875bdb63 ("powerpc/64s: fix handling of non-synchronous machine
checks") removed the last usage.
Signed-off-by: Balbir Singh <bsingharora@gmail.com> Reviewed-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Vaibhav Jain [Wed, 11 Oct 2017 06:14:41 +0000 (11:44 +0530)]
cxl: Dump PSL_FIR register on PSL9 error irq
For PSL9 currently we aren't dumping the PSL FIR register when a
PSL error interrupt is triggered. Contents of this register are useful
in debugging AFU issues.
This patch fixes issue by adding a new service_layer_ops callback
cxl_native_err_irq_dump_regs_psl9() to dump the PSL_FIR registers on a
PSL error interrupt thereby bringing the behavior in line with PSL on
POWER-8. Also the existing service_layer_ops callback
for PSL8 has been renamed to cxl_native_err_irq_dump_regs_psl8().
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com> Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Vaibhav Jain [Mon, 9 Oct 2017 17:56:27 +0000 (23:26 +0530)]
cxl: Rename register PSL9_FIR2 to PSL9_FIR_MASK
PSL9 doesn't have a FIR2 register as was the case with PSL8. However
currently the register definitions in 'cxl.h' have a definition for
PSL9_FIR2 that actually points to PSL9_FIR_MASK register in the P1
area at offset 0x308.
So this patch renames the def PSL9_FIR2 to PSL9_FIR_MASK and updates
the references in the code to point to the new identifier. It also
removes the code to dump contents of FIR2 (FIR_MASK actually) in
cxl_native_irq_dump_regs_psl9().
The PSL initialization sequence has been updated to DD2.
This patch adapts to the changes, retaining compatibility with DD1.
The patch includes some changes to DD1 fix-ups as well.
Tests performed on some of the old/new hardware.
The function is_page_fault(), for POWER9, lists the Translation Checkout
Responses where the page fault will be handled by copro_handle_mm_fault().
This list is too restrictive and not necessary.
This patches removes this restriction and all page faults, whatever the
reason, will be handled. In this case, the interruption is always
acknowledged.
The following features will be added soon:
- phb reset when switching to capi mode.
- cxllib update to support new functions.
Kautuk Consul [Tue, 19 Apr 2016 10:18:21 +0000 (15:48 +0530)]
powerpc: get_wchan(): solve possible race scenario due to parallel wakeup
Add a check for p->state == TASK_RUNNING so that any wake-ups on
task_struct p in the interim lead to 0 being returned by get_wchan().
Signed-off-by: Kautuk Consul <kautuk.consul.1980@gmail.com>
[mpe: Confirmed other architectures do similar] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
selftests/powerpc: Use snprintf to construct DSCR sysfs interface paths
Currently sprintf is used, and while paths should never exceed
the size of the buffer it is theoretically possible since
dirent.d_name is 256 bytes. As a result this trips
-Wformat-overflow, and since the test is built with -Wall -Werror
the causes the build to fail. Switch to using snprintf and skip
any paths which are too long for the filename buffer.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc: Always initialize input array when calling epapr_hypercall()
Several callers to epapr_hypercall() pass an uninitialized stack
allocated array for the input arguments, presumably because they
have no input arguments. However this can produce errors like
this one
arch/powerpc/include/asm/epapr_hcalls.h:470:42: error: 'in' may be used uninitialized in this function [-Werror=maybe-uninitialized]
unsigned long register r3 asm("r3") = in[0];
~~^~~
Fix callers to this function to always zero-initialize the input
arguments array to prevent this.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/xmon: Add option to show uptime information
It might be useful to quickly get the uptime of a running system on
xmon, without needing to grab data from memory and doing math on
struct addresses.
For example, it'd be useful to check for how long after a crash a
system is on xmon shell or if some test was started after the first
test crashed (and this 2nd test crashed too into xmon).
This small patch adds the 'U' command, to accomplish this.
Suggested-by: Murilo Fossa Vicentini <muvic@linux.vnet.ibm.com> Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
[mpe: Display units (seconds), add sync()/__delay() sequence] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Fri, 29 Sep 2017 03:58:02 +0000 (13:58 +1000)]
powerpc/powernv: Make opal_event_shutdown() callable from IRQ context
In opal_event_shutdown() we free all the IRQs hanging off the
opal_event_irqchip. However it's not safe to do so if we're called
from IRQ context, because free_irq() wants to synchronise versus IRQ
context. This can lead to warnings and a stuck system.
We can avoid that by using disable_irq_nosync() rather than
free_irq(). Although it doesn't fully free the IRQ, it should be
sufficient when we're shutting down, particularly in an emergency.
Add an in_interrupt() check and use free_irq() when we're shutting
down normally. It's probably OK to use disable_irq_nosync() in that
case too, but for now it's safer to leave that behaviour as-is.
Fixes: 9f0fd0499d30 ("powerpc/powernv: Add a virtual irqchip for opal events") Reported-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The issue is that we aren't disabling preemption in
kprobe_ftrace_handler(). Disable it.
Fixes: ead514d5fb30a0 ("powerpc/kprobes: Add support for KPROBES_ON_FTRACE") Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
[mpe: Trim oops a little for formatting] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit c05b8c4474c030 ("powerpc/kprobes: Skip livepatch_handler() for
jprobes") introduced a helper is_current_kprobe_addr() to help determine
if the current function has been livepatched or if it has a jprobe
installed, both of which modify the NIP. This was subsequently renamed
to __is_active_jprobe().
In the case of a jprobe, kprobe_ftrace_handler() disables pre-emption
before calling into setjmp_pre_handler() which returns without disabling
pre-emption. This is done to ensure that the jprobe handler won't
disappear beneath us if the jprobe is unregistered between the
setjmp_pre_handler() and the subsequent longjmp_break_handler() called
from the jprobe handler. Due to this, we can use __this_cpu_read() in
__is_active_jprobe() with the pre-emption check as we know that
pre-emption will be disabled.
However, if this function has been livepatched, we are still doing this
check and when we do so, pre-emption won't necessarily be disabled. This
results in the call trace shown above.
Fix this by only invoking __is_active_jprobe() when pre-emption is
disabled. And since we now guard this within a pre-emption check, we can
instead use raw_cpu_read() to get the current_kprobe value skipping the
check done by __this_cpu_read().
Fixes: c05b8c4474c030 ("powerpc/kprobes: Skip livepatch_handler() for jprobes") Reported-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com> Tested-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com> Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/kprobes: Clean up jprobe detection in livepatch handler
In commit c05b8c4474c03 ("powerpc/kprobes: Skip livepatch_handler() for
jprobes"), we added a helper is_current_kprobe_addr() to help detect if
the modified regs->nip was due to a jprobe or livepatch. Masami felt
that the function name was not quite clear. To that end, this patch
renames is_current_kprobe_addr() to __is_active_jprobe() and adds a
comment to (hopefully) better clarify the purpose of this helper. The
helper has also now been moved to kprobes-ftrace.c so that it is only
available for KPROBES_ON_FTRACE.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/kprobes: Do not suppress instruction emulation if a single run failed
Currently, we disable instruction emulation if emulate_step() fails for
any reason. However, such failures could be transient and specific to a
particular run. Instead, only disable instruction emulation if we have
never been able to emulate this. If we had emulated this instruction
successfully at least once, then we single step only this probe hit and
continue to try emulating the instruction in subsequent probe hits.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Joel Stanley [Wed, 4 Oct 2017 04:23:24 +0000 (14:53 +1030)]
powerpc/configs: Add Skiroot defconfig
This configuration is used by the OpenPower firmware for it's
Linux-as-bootloader implementation. Also known as the Petitboot
kernel, this configuration broke in 4.12 (CPU_HOTPLUG=n), so add it to
the upstream tree in order to get better coverage.
Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sandipan Das [Fri, 29 Sep 2017 05:44:10 +0000 (11:14 +0530)]
powerpc/lib/sstep: Fix fixed-point shift instructions that set CA32
This fixes the emulated behaviour of existing fixed-point shift right
algebraic instructions that are supposed to set both the CA and CA32
bits of XER when running on a system that is compliant with POWER ISA
v3.0 independent of whether the system is executing in 32-bit mode or
64-bit mode. The following instructions are affected:
* Shift Right Algebraic Word Immediate (srawi[.])
* Shift Right Algebraic Word (sraw[.])
* Shift Right Algebraic Doubleword Immediate (sradi[.])
* Shift Right Algebraic Doubleword (srad[.])
Fixes: 0016a4cf5582 ("powerpc: Emulate most Book I instructions in emulate_step()") Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sandipan Das [Fri, 29 Sep 2017 05:44:09 +0000 (11:14 +0530)]
powerpc/lib/sstep: Fix fixed-point arithmetic instructions that set CA32
There are existing fixed-point arithmetic instructions that always set the
CA bit of XER to reflect the carry out of bit 0 in 64-bit mode and out of
bit 32 in 32-bit mode. In ISA v3.0, these instructions also always set the
CA32 bit of XER to reflect the carry out of bit 32.
This fixes the emulated behaviour of such instructions when running on a
system that is compliant with POWER ISA v3.0. The following instructions
are affected:
* Add Immediate Carrying (addic)
* Add Immediate Carrying and Record (addic.)
* Subtract From Immediate Carrying (subfic)
* Add Carrying (addc[.])
* Subtract From Carrying (subfc[.])
* Add Extended (adde[.])
* Subtract From Extended (subfe[.])
* Add to Minus One Extended (addme[.])
* Subtract From Minus One Extended (subfme[.])
* Add to Zero Extended (addze[.])
* Subtract From Zero Extended (subfze[.])
Fixes: 0016a4cf5582 ("powerpc: Emulate most Book I instructions in emulate_step()") Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sandipan Das [Fri, 29 Sep 2017 05:44:08 +0000 (11:14 +0530)]
powerpc/lib/sstep: Add XER bits introduced in POWER ISA v3.0
This adds definitions for the OV32 and CA32 bits of XER that
were introduced in POWER ISA v3.0. There are some existing
instructions that currently set the OV and CA bits based on
certain conditions.
The emulation behaviour of all these instructions needs to
be updated to set these new bits accordingly.
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com> Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 29 Sep 2017 03:29:42 +0000 (13:29 +1000)]
powerpc/powernv: Implement NMI IPI with OPAL_SIGNAL_SYSTEM_RESET
This allows MSR[EE]=0 lockups to be detected on an OPAL (bare metal)
system similarly to the hcall NMI IPI on pseries guests, when the
platform/firmware supports it.
This is an example of CPU10 spinning with interrupts hard disabled:
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Use kernel types for opal_signal_system_reset()] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 29 Sep 2017 03:29:41 +0000 (13:29 +1000)]
powerpc/64s: Implement system reset idle wakeup reason
It is possible to wake from idle due to a system reset exception, in
which case the CPU takes a system reset interrupt to wake from idle,
with system reset as the wakeup reason.
The regular (not idle wakeup) system reset interrupt handler must be
invoked in this case, otherwise the system reset interrupt is lost.
Handle the system reset interrupt immediately after CPU state has been
restored.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The SMP hardlockup watchdog cross-checks other CPUs for lockups, which
causes xmon headaches because it's assuming interrupts hard disabled
means no watchdog troubles. Try to improve that by calling
touch_nmi_watchdog() in obvious places where secondaries are spinning.
Also annotate these spin loops with spin_begin/end calls.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 29 Sep 2017 03:29:39 +0000 (13:29 +1000)]
powerpc/watchdog: Do not trigger SMP crash from touch_nmi_watchdog
In xmon, touch_nmi_watchdog() is not expected to be checking that
other CPUs have not touched the watchdog, so the code will just call
touch_nmi_watchdog() once before re-enabling hard interrupts.
Just update our CPU's state, and ignore apparently stuck SMP threads.
Arguably touch_nmi_watchdog should check for SMP lockups, and callers
should be fixed, but that's not trivial for the input code of xmon.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 29 Sep 2017 03:29:38 +0000 (13:29 +1000)]
powerpc/watchdog: Do not backtrace locked CPUs twice if allcpus backtrace is enabled
If sysctl_hardlockup_all_cpu_backtrace is enabled, there is no need to
IPI stuck CPUs for backtrace before trigger_allbutself_cpu_backtrace(),
which does the same thing again.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 29 Sep 2017 03:29:37 +0000 (13:29 +1000)]
powerpc/watchdog: Do not panic from locked CPU's IPI handler
The SMP watchdog will detect locked CPUs and IPI them to print a
backtrace and registers. If panic on hard lockup is enabled, do not
panic from this handler, because that can cause recursion into the IPI
layer during the panic.
The caller already panics in this case.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make sure to set the valid-bit in software-state field of the
populated PE. This was earlier missing for dedicated mode AFUs, hence
was causing a PSL freeze when the AFU was activated.
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com> Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The PSL and nMMU need to see all TLB invalidations for the memory
contexts used on the adapter. For the hash memory model, it is done by
making all TLBIs global as soon as the cxl driver is in use. For
radix, we need something similar, but we can refine and only convert
to global the invalidations for contexts actually used by the device.
The new mm_context_add_copro() API increments the 'active_cpus' count
for the contexts attached to the cxl adapter. As soon as there's more
than 1 active cpu, the TLBIs for the context become global. Active cpu
count must be decremented when detaching to restore locality if
possible and to avoid overflowing the counter.
The hash memory model support is somewhat limited, as we can't
decrement the active cpus count when mm_context_remove_copro() is
called, because we can't flush the TLB for a mm on hash. So TLBIs
remain global on hash.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Fixes: f24be42aab37 ("cxl: Add psl9 specific code") Tested-by: Alistair Popple <alistair@popple.id.au>
[mpe: Fold in updated comment on the barrier from Fred] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With the optimizations introduced by commit a46cc7a90fd8
("powerpc/mm/radix: Improve TLB/PWC flushes"), flush_tlb_mm() no
longer flushes the page walk cache (PWC) with radix. This patch
introduces flush_all_mm(), which flushes everything, TLB and PWC, for
a given mm.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Reviewed-By: Alistair Popple <alistair@popple.id.au>
[mpe: Add a WARN_ON_ONCE() in the empty hash routines] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Neuling [Fri, 15 Sep 2017 05:25:48 +0000 (15:25 +1000)]
powerpc/64s: Add workaround for P9 vector CI load issue
POWER9 DD2.1 and earlier has an issue where some cache inhibited
vector load will return bad data. The workaround is two part, one
firmware/microcode part triggers HMI interrupts when hitting such
loads, the other part is this patch which then emulates the
instructions in Linux.
The affected instructions are limited to lxvd2x, lxvw4x, lxvb16x and
lxvh8x.
When an instruction triggers the HMI, all threads in the core will be
sent to the HMI handler, not just the one running the vector load.
In general, these spurious HMIs are detected by the emulation code and
we just return back to the running process. Unfortunately, if a
spurious interrupt occurs on a vector load that's to normal memory we
have no way to detect that it's spurious (unless we walk the page
tables, which is very expensive). In this case we emulate the load but
we need do so using a vector load itself to ensure 128bit atomicity is
preserved.
Some additional debugfs emulated instruction counters are added also.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Switch CONFIG_PPC_BOOK3S_64 to CONFIG_VSX to unbreak the build] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/powernv: Rework EEH initialization on powernv
Remove the post_init callback which is only used
by powernv, we can just call it explicitly from
the powernv code.
This partially kills the ability to "disable" eeh at
runtime via debugfs as this was calling that same
callback again, but this is both unused and broken
in several ways. If we want to revive it, we need
to create a dedicated enable/disable callback on the
backend that does the right thing.
Let the bulk of eeh initialize normally at
core_initcall() like it does on pseries by removing
the hack in eeh_init() that delays it.
Instead we make sure our eeh->probe cleanly bails
out of the PEs haven't been created yet and we force
a re-probe where we used to call eeh_init() again.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Russell Currey <ruscur@russell.cc> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge tag 'devicetree-fixes-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- fix build for !OF providing empty of_find_device_by_node
- fix Abracon vendor prefix
- sync dtx_diff include paths (again)
- a stm32h7 clock binding doc fix
* tag 'devicetree-fixes-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: clk: stm32h7: fix clock-cell size
scripts/dtc: dtx_diff - 2nd update of include dts paths to match build
dt-bindings: fix vendor prefix for Abracon
of: provide inline helper for of_find_device_by_node
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Another round of CR3/PCID related fixes (I think this addresses all
but one of the known problems with PCID support), an objtool fix plus
a Clang fix that (finally) solves all Clang quirks to build a bootable
x86 kernel as-is"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm: Fix inline asm call constraints for Clang
objtool: Handle another GCC stack pointer adjustment bug
x86/mm/32: Load a sane CR3 before cpu_init() on secondary CPUs
x86/mm/32: Move setup_clear_cpu_cap(X86_FEATURE_PCID) earlier
x86/mm/64: Stop using CR3.PCID == 0 in ASID-aware code
x86/mm: Factor out CR3-building code
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"Three irqchip driver fixes, and an affinity mask helper function bug
fix affecting x86"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "genirq: Restrict effective affinity to interrupts actually using it"
irqchip.mips-gic: Fix shared interrupt mask writes
irqchip/gic-v4: Fix building with ancient gcc
irqchip/gic-v3: Iterate over possible CPUs by for_each_possible_cpu()
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull address-limit checking fixes from Ingo Molnar:
"This fixes a number of bugs in the address-limit (USER_DS) checks that
got introduced in the merge window, (mostly) affecting the ARM and
ARM64 platforms"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arm64/syscalls: Move address limit check in loop
arm/syscalls: Optimize address limit check
Revert "arm/syscalls: Check address limit on user-mode return"
syscalls: Use CHECK_DATA_CORRUPTION for addr_limit_user_check
Merge branch 'next-general' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull misc security layer update from James Morris:
"This is the remaining 'general' change in the security tree for v4.14,
following the direct merging of SELinux (+ TOMOYO), AppArmor, and
seccomp.
That's everything now for the security tree except IMA, which will
follow shortly (I've been traveling for the past week with patchy
internet)"
* 'next-general' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
security: fix description of values returned by cap_inode_need_killpriv
Merge branch 'next-tpm' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull TPM updates from James Morris:
"Here are the TPM updates from Jarkko for v4.14, which I've placed in
their own branch (next-tpm). I ended up cherry-picking them as other
changes had been made in Jarkko's branch after he sent me his original
pull request.
I plan on maintaining a separate branch for TPM (and other security
subsystems) from now on.
From Jarkko: 'Not much this time except a few fixes'"
* 'next-tpm' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
tpm: ibmvtpm: simplify crq initialization and document crq format
tpm: replace msleep() with usleep_range() in TPM 1.2/2.0 generic drivers
Documentation: tpm: add powered-while-suspended binding documentation
tpm: tpm_crb: constify acpi_device_id.
tpm: vtpm: constify vio_device_id
Michal Suchanek [Fri, 24 Feb 2017 19:35:16 +0000 (20:35 +0100)]
tpm: ibmvtpm: simplify crq initialization and document crq format
The crq is passed in registers and is the same on BE and LE hosts.
However, current implementation allocates a structure on-stack to
represent the crq, initializes the members swapping them to BE, and
loads the structure swapping it from BE. This is pointless and causes
GCC warnings about ununitialized members. Get rid of the structure and
the warnings.
Signed-off-by: Michal Suchanek <msuchanek@suse.de> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.l.morris@oracle.com>
Hamza Attak [Mon, 14 Aug 2017 18:09:16 +0000 (19:09 +0100)]
tpm: replace msleep() with usleep_range() in TPM 1.2/2.0 generic drivers
The patch simply replaces all msleep function calls with usleep_range calls
in the generic drivers.
Tested with an Infineon TPM 1.2, using the generic tpm-tis module, for a
thousand PCR extends, we see results going from 1m57s unpatched to 40s
with the new patch. We obtain similar results when using the original and
patched tpm_infineon driver, which is also part of the patch.
Similarly with a STM TPM 2.0, using the CRB driver, it takes about 20ms per
extend unpatched and around 7ms with the new patch.
Note that the PCR consistency is untouched with this patch, each TPM has
been tested with 10 million extends and the aggregated PCR value is
continuously verified to be correct.
As an extension of this work, this could potentially and easily be applied
to other vendor's drivers. Still, these changes are not included in the
proposed patch as they are untested.
Signed-off-by: Hamza Attak <hamza@hpe.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.l.morris@oracle.com>
Add a new powered-while-suspended property to control the behavior of the
TPM suspend/resume.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Sonny Rao <sonnyrao@chromium.org> Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.l.morris@oracle.com>
acpi_device_id are not supposed to change at runtime. All functions
working with acpi_device_id provided by <acpi/acpi_bus.h> work with
const acpi_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
4198 608 0 4806 12c6 drivers/char/tpm/tpm_crb.o
File size After adding 'const':
text data bss dec hex filename
4262 520 0 4782 12ae drivers/char/tpm/tpm_crb.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.l.morris@oracle.com>
Arvind Yadav [Thu, 17 Aug 2017 17:34:21 +0000 (23:04 +0530)]
tpm: vtpm: constify vio_device_id
vio_device_id are not supposed to change at runtime. All functions
working with vio_device_id provided by <asm/vio.h> work with
const vio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.l.morris@oracle.com>
Stefan Berger [Thu, 27 Jul 2017 02:27:05 +0000 (22:27 -0400)]
security: fix description of values returned by cap_inode_need_killpriv
cap_inode_need_killpriv returns 1 if security.capability exists and
has a value and inode_killpriv() is required, 0 otherwise. Fix the
description of the return value to reflect this.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com> Reviewed-by: Serge Hallyn <serge@hallyn.com> Signed-off-by: James Morris <james.l.morris@oracle.com>
Merge branch 'parisc-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
- Unbreak parisc bootloader by avoiding a gcc-7 optimization to convert
multiple byte-accesses into one word-access.
- Add missing HWPOISON page fault handler code. I completely missed
that when I added HWPOISON support during this merge window and it
only showed up now with the madvise07 LTP test case.
- Fix backtrace unwinding to stop when stack start has been reached.
- Issue warning if initrd has been loaded into memory regions with
broken RAM modules.
- Fix HPMC handler (parisc hardware fault handler) to comply with
architecture specification.
- Avoid compiler warnings about too large frame sizes.
- Minor init-section fixes.
* 'parisc-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Unbreak bootloader due to gcc-7 optimizations
parisc: Reintroduce option to gzip-compress the kernel
parisc: Add HWPOISON page fault handler code
parisc: Move init_per_cpu() into init section
parisc: Check if initrd was loaded into broken RAM
parisc: Add PDCE_CHECK instruction to HPMC handler
parisc: Add wrapper for pdc_instr() firmware function
parisc: Move start_parisc() into init section
parisc: Stop unwinding at start of stack
parisc: Fix too large frame size warnings
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
- Smattering of miscellanous fixes
- A five patch series for i40iw that had a patch (5/5) that was larger
than I would like, but I took it because it's needed for large scale
users
- An 8 patch series for bnxt_re that landed right as I was leaving on
PTO and so had to wait until now...they are all appropriate fixes for
-rc IMO
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (22 commits)
bnxt_re: Don't issue cmd to delete GID for QP1 GID entry before the QP is destroyed
bnxt_re: Fix memory leak in FRMR path
bnxt_re: Remove RTNL lock dependency in bnxt_re_query_port
bnxt_re: Fix race between the netdev register and unregister events
bnxt_re: Free up devices in module_exit path
bnxt_re: Fix compare and swap atomic operands
bnxt_re: Stop issuing further cmds to FW once a cmd times out
bnxt_re: Fix update of qplib_qp.mtu when modified
i40iw: Add support for port reuse on active side connections
i40iw: Add missing VLAN priority
i40iw: Call i40iw_cm_disconn on modify QP to disconnect
i40iw: Prevent multiple netdev event notifier registrations
i40iw: Fail open if there are no available MSI-X vectors
RDMA/vmw_pvrdma: Fix reporting correct opcodes for completion
IB/bnxt_re: Fix frame stack compilation warning
IB/mlx5: fix debugfs cleanup
IB/ocrdma: fix incorrect fall-through on switch statement
IB/ipoib: Suppress the retry related completion errors
iw_cxgb4: remove the stid on listen create failure
iw_cxgb4: drop listen destroy replies if no ep found
...
1) Fix NAPI poll list corruption in enic driver, from Christian
Lamparter.
2) Fix route use after free, from Eric Dumazet.
3) Fix regression in reuseaddr handling, from Josef Bacik.
4) Assert the size of control messages in compat handling since we copy
it in from userspace twice. From Meng Xu.
5) SMC layer bug fixes (missing RCU locking, bad refcounting, etc.)
from Ursula Braun.
6) Fix races in AF_PACKET fanout handling, from Willem de Bruijn.
7) Don't use ARRAY_SIZE on spinlock array which might have zero
entries, from Geert Uytterhoeven.
8) Fix miscomputation of checksum in ipv6 udp code, from Subash Abhinov
Kasiviswanathan.
9) Push the ipv6 header properly in ipv6 GRE tunnel driver, from Xin
Long.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
inet: fix improper empty comparison
net: use inet6_rcv_saddr to compare sockets
net: set tb->fast_sk_family
net: orphan frags on stand-alone ptype in dev_queue_xmit_nit
MAINTAINERS: update git tree locations for ieee802154 subsystem
net: prevent dst uses after free
net: phy: Fix truncation of large IRQ numbers in phy_attached_print()
net/smc: no close wait in case of process shut down
net/smc: introduce a delay
net/smc: terminate link group if out-of-sync is received
net/smc: longer delay for client link group removal
net/smc: adapt send request completion notification
net/smc: adjust net_device refcount
net/smc: take RCU read lock for routing cache lookup
net/smc: add receive timeout check
net/smc: add missing dev_put
net: stmmac: Cocci spatch "of_table"
lan78xx: Use default values loaded from EEPROM/OTP after reset
lan78xx: Allow EEPROM write for less than MAX_EEPROM_SIZE
lan78xx: Fix for eeprom read/write when device auto suspend
...
Merge tag 'apparmor-pr-2017-09-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor
Pull apparmor updates from John Johansen:
"This is the apparmor pull request, similar to SELinux and seccomp.
It's the same series that I was sent to James' security tree + one
regression fix that was found after the series was sent to James and
would have been sent for v4.14-rc2.
Features:
- in preparation for secid mapping add support for absolute root view
based labels
- add base infastructure for socket mediation
- add mount mediation
- add signal mediation
minor cleanups and changes:
- be defensive, ensure unconfined profiles have dfas initialized
- add more debug asserts to apparmorfs
- enable policy unpacking to audit different reasons for failure
- cleanup conditional check for label in label_print
- Redundant condition: prev_ns. in [label.c:1498]
Bug Fixes:
- fix regression in apparmorfs DAC access permissions
- fix build failure on sparc caused by undeclared signals
- fix sparse report of incorrect type assignment when freeing label proxies
- fix race condition in null profile creation
- Fix an error code in aafs_create()
- Fix logical error in verify_header()
- Fix shadowed local variable in unpack_trans_table()"
* tag 'apparmor-pr-2017-09-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor:
apparmor: fix apparmorfs DAC access permissions
apparmor: fix build failure on sparc caused by undeclared signals
apparmor: fix incorrect type assignment when freeing proxies
apparmor: ensure unconfined profiles have dfas initialized
apparmor: fix race condition in null profile creation
apparmor: move new_null_profile to after profile lookup fns()
apparmor: add base infastructure for socket mediation
apparmor: add more debug asserts to apparmorfs
apparmor: make policy_unpack able to audit different info messages
apparmor: add support for absolute root view based labels
apparmor: cleanup conditional check for label in label_print
apparmor: add mount mediation
apparmor: add the ability to mediate signals
apparmor: Redundant condition: prev_ns. in [label.c:1498]
apparmor: Fix an error code in aafs_create()
apparmor: Fix logical error in verify_header()
apparmor: Fix shadowed local variable in unpack_trans_table()
x86/asm: Fix inline asm call constraints for Clang
For inline asm statements which have a CALL instruction, we list the
stack pointer as a constraint to convince GCC to ensure the frame
pointer is set up first:
With GCC 7.2, however, GCC's behavior has changed. It now changes its
behavior based on the conversion of the register variable to a global.
That somehow convinces it to *always* set up the frame pointer before
inserting *any* inline asm. (Therefore, listing the variable as an
output constraint is a no-op and is no longer necessary.) It's a bit
overkill, but the performance impact should be negligible. And in fact,
there's a nice improvement with frame pointers disabled:
So in summary, while listing the stack pointer as an output constraint
is no longer necessary for newer versions of GCC, it's still needed for
older versions.
But now that objtool is paying attention to such stack pointer writes
to/from a register, it needs to understand them properly. In this case
that means recognizing that the "mov %rsp, %rax" instruction is
potentially a backup of the stack pointer.
Merge tag 'acpi-4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix the initialization of resources in the ACPI WDAT watchdog
driver, a recent regression in the ACPI device properties handling, a
recent change in behavior causing the ACPI_HANDLE() macro to only work
for GPL code and create a MAINTAINERS entry for ACPI PMIC drivers in
order to specify the official reviewers for that code.
Specifics:
- Fix the initialization of resources in the ACPI WDAT watchdog
driver that uses unititialized memory which causes compiler
warnings to be triggered (Arnd Bergmann).
- Fix a recent regression in the ACPI device properties handling that
causes some device properties data to be skipped during enumeration
(Sakari Ailus).
- Fix a recent change in behavior that caused the ACPI_HANDLE() macro
to stop working for non-GPL code which is a problem for the NVidia
binary graphics driver, for example (John Hubbard).
- Add a MAINTAINERS entry for the ACPI PMIC drivers to specify the
official reviewers for that code (Rafael Wysocki)"
* tag 'acpi-4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: properties: Return _DSD hierarchical extension (data) sub-nodes correctly
ACPI / bus: Make ACPI_HANDLE() work for non-GPL code again
ACPI / watchdog: properly initialize resources
ACPI / PMIC: Add code reviewers to MAINTAINERS
I introduced a regression when reworking the fastreuse port stuff that allows
bind conflicts to occur once a reuseaddr successfully opens on an existing tb.
The root cause is I reversed an if statement which caused us to set the tb as if
there were no owners on the socket if there were, which obviously is not
correct.
Dave could you please queue these changes up for -stable, I've run them through
the net tests and added another test to check for this problem specifically.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Sat, 23 Sep 2017 00:20:08 +0000 (20:20 -0400)]
inet: fix improper empty comparison
When doing my reuseport rework I screwed up and changed a
if (hlist_empty(&tb->owners))
to
if (!hlist_empty(&tb->owners))
This is obviously bad as all of the reuseport/reuse logic was reversed,
which caused weird problems like allowing an ipv4 bind conflict if we
opened an ipv4 only socket on a port followed by an ipv6 only socket on
the same port.
Fixes: b9470c27607b ("inet: kill smallest_size and smallest_port") Reported-by: Cole Robinson <crobinso@redhat.com> Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-bionic-kernel.git / log