Guenter Roeck [Wed, 8 Feb 2017 22:07:42 +0000 (14:07 -0800)]
hwmon: (it87) Do not overwrite bit 2..6 of pwm control registers
In IT8620E, after setting pwm control to manual, it was observed that
pwm values for fan 4..6 have reversed results (writing 0 results in fans
running at full speed, writing 255 results in fans turned off).
With the new PWM control, pwm polarity for pwm control 4..6 is specified
in its pwm control registers. Those registers are overwritten when setting
the pwm mode or the temperature mapping. Do not touch bit 2..6 of pwm
control registers on register writes to fix the problem.
Guenter Roeck [Wed, 8 Feb 2017 22:05:56 +0000 (14:05 -0800)]
hwmon: (it87) Fix pwm4 detection for IT8620 and IT8628
pwm4 is enabled if bit 2 of GPIO control register 4 is disabled,
not when it is enabled. Since the check is for the skip condition,
it is reversed. This applies to both IT8620 and IT8628.
Fixes: 36c4d98a7883d ("hwmon: (it87) Add support for all pwm channels ...") Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Guenter Roeck [Wed, 8 Feb 2017 22:02:59 +0000 (14:02 -0800)]
hwmon: (it87) Ensure that pwm control cache is current before updating values
If sensor attributes were never read, the pwm control data has not been
initiialized, which can cause wrong driver behavior. Ensure that cached
data is current before acting on it.
Omar Sandoval [Fri, 10 Feb 2017 23:03:35 +0000 (15:03 -0800)]
Btrfs: fix btrfs_decompress_buf2page()
If btrfs_decompress_buf2page() is handed a bio with its page in the
middle of the working buffer, then we adjust the offset into the working
buffer. After we copy into the bio, we advance the iterator by the
number of bytes we copied. Then, we have some logic to handle the case
of discontiguous pages and adjust the offset into the working buffer
again. However, if we didn't advance the bio to a new page, we may enter
this case in error, essentially repeating the adjustment that we already
made when we entered the function. The end result is bogus data in the
bio.
Previously, we only checked for this case when we advanced to a new
page, but the conversion to bio iterators changed that. This restores
the old, correct behavior.
After bio_advance(), we are still in the same page, so start_byte is the
same. Then, we check (total_out > start_byte && current_buf_start < start_byte),
which is true! So, we adjust the values again:
But note that working_bytes was already zero before this, so we should
have stopped copying.
Fixes: 974b1adc3b10 ("btrfs: use bio iterators for the decompression handlers") Reported-by: Pat Erley <pat-lkml@erley.org> Reviewed-by: Chris Mason <clm@fb.com> Signed-off-by: Omar Sandoval <osandov@fb.com> Signed-off-by: Chris Mason <clm@fb.com> Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Tested-by: Liu Bo <bo.li.liu@oracle.com>
1) If the timing is wrong we can indefinitely stop generating new ipv6
temporary addresses, from Marcus Huewe.
2) Don't double free per-cpu stats in ipv6 SIT tunnel driver, from Cong
Wang.
3) Put protections in place so that AF_PACKET is not able to submit
packets which don't even have a link level header to drivers. From
Willem de Bruijn.
4) Fix memory leaks in ipv4 and ipv6 multicast code, from Hangbin Liu.
5) Don't use udp_ioctl() in l2tp code, UDP version expects a UDP socket
and that doesn't go over very well when it is passed an L2TP one.
Fix from Eric Dumazet.
6) Don't crash on NULL pointer in phy_attach_direct(), from Florian
Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
l2tp: do not use udp_ioctl()
xen-netfront: Delete rx_refill_timer in xennet_disconnect_backend()
NET: mkiss: Fix panic
net: hns: Fix the device being used for dma mapping during TX
net: phy: Initialize mdio clock at probe function
igmp, mld: Fix memory leak in igmpv3/mld_del_delrec()
xen-netfront: Improve error handling during initialization
sierra_net: Skip validating irrelevant fields for IDLE LSIs
sierra_net: Add support for IPv6 and Dual-Stack Link Sense Indications
kcm: fix 0-length case for kcm_sendmsg()
xen-netfront: Rework the fix for Rx stall during OOM and network stress
net: phy: Fix PHY module checks and NULL deref in phy_attach_direct()
net: thunderx: Fix PHY autoneg for SGMII QLM mode
net: dsa: Do not destroy invalid network devices
ping: fix a null pointer dereference
packet: round up linear to header len
net: introduce device min_header_len
sit: fix a double free on error path
lwtunnel: valid encap attr check should return 0 when lwtunnel is disabled
ipv6: addrconf: fix generation of new temporary addresses
Linus Torvalds [Fri, 10 Feb 2017 22:29:30 +0000 (14:29 -0800)]
Merge tag 'sound-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are some last-minute fixes: two fixes for races in ALSA sequencer
queue spotted by syzkaller, a revert for a regression of LINE6 driver
(since 4.9), and a trivial new codec ID addition for Nvidia HDMI"
* tag 'sound-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - adding a new NV HDMI/DP codec ID in the driver
ALSA: seq: Fix race at creating a queue
Revert "ALSA: line6: Only determine control port properties if needed"
ALSA: seq: Don't handle loop timeout at snd_seq_pool_done()
Linus Torvalds [Fri, 10 Feb 2017 22:23:45 +0000 (14:23 -0800)]
Merge tag 'nfsd-4.10-3' of git://linux-nfs.org/~bfields/linux
Pull nfsd revert from Bruce Fields:
"This patch turned out to have a couple problems. The problems are
fixable, but at least one of the fixes is a little ugly. The original
bug has always been there, so we can wait another week or two to get
this right"
* tag 'nfsd-4.10-3' of git://linux-nfs.org/~bfields/linux:
nfsd: Revert "nfsd: special case truncates some more"
Linus Torvalds [Fri, 10 Feb 2017 22:10:35 +0000 (14:10 -0800)]
Merge tag 'powerpc-4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes friom Michael Ellerman:
"Apologies for the late pull request, but Ben has been busy finding bugs.
- Userspace was semi-randomly segfaulting on radix due to us
incorrectly handling a fault triggered by autonuma, caused by a
patch we merged earlier in v4.10 to prevent the kernel executing
userspace.
- We weren't marking host IPIs properly for KVM in the OPAL ICP
backend.
- The ERAT flushing on radix was missing an isync and was incorrectly
marked as DD1 only.
- The powernv CPU hotplug code was missing a wakeup type and failing
to flush the interrupt correctly when using OPAL ICP
Thanks to Benjamin Herrenschmidt"
* tag 'powerpc-4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv: Properly set "host-ipi" on IPIs
powerpc/powernv: Fix CPU hotplug to handle waking on HVI
powerpc/mm/radix: Update ERAT flushes when invalidating TLB
powerpc/mm: Fix spurrious segfaults on radix with autonuma
Eric Dumazet [Fri, 10 Feb 2017 00:15:52 +0000 (16:15 -0800)]
l2tp: do not use udp_ioctl()
udp_ioctl(), as its name suggests, is used by UDP protocols,
but is also used by L2TP :(
L2TP should use its own handler, because it really does not
look the same.
SIOCINQ for instance should not assume UDP checksum or headers.
Thanks to Andrey and syzkaller team for providing the report
and a nice reproducer.
While crashes only happen on recent kernels (after commit 7c13f97ffde6 ("udp: do fwd memory scheduling on dequeue")), this
probably needs to be backported to older kernels.
Fixes: 7c13f97ffde6 ("udp: do fwd memory scheduling on dequeue") Fixes: 85584672012e ("udp: Fix udp_poll() and ioctl()") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Boris Ostrovsky [Mon, 30 Jan 2017 17:45:46 +0000 (12:45 -0500)]
xen-netfront: Delete rx_refill_timer in xennet_disconnect_backend()
rx_refill_timer should be deleted as soon as we disconnect from the
backend since otherwise it is possible for the timer to go off before
we get to xennet_destroy_queues(). If this happens we may dereference
queue->rx.sring which is set to NULL in xennet_disconnect_backend().
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> CC: stable@vger.kernel.org Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ralf Baechle [Thu, 9 Feb 2017 13:12:11 +0000 (14:12 +0100)]
NET: mkiss: Fix panic
If a USB-to-serial adapter is unplugged, the driver re-initializes, with
dev->hard_header_len and dev->addr_len set to zero, instead of the correct
values. If then a packet is sent through the half-dead interface, the
kernel will panic due to running out of headroom in the skb when pushing
for the AX.25 headers resulting in this panic:
[<c0595468>] (skb_panic) from [<c0401f70>] (skb_push+0x4c/0x50)
[<c0401f70>] (skb_push) from [<bf0bdad4>] (ax25_hard_header+0x34/0xf4 [ax25])
[<bf0bdad4>] (ax25_hard_header [ax25]) from [<bf0d05d4>] (ax_header+0x38/0x40 [mkiss])
[<bf0d05d4>] (ax_header [mkiss]) from [<c041b584>] (neigh_compat_output+0x8c/0xd8)
[<c041b584>] (neigh_compat_output) from [<c043e7a8>] (ip_finish_output+0x2a0/0x914)
[<c043e7a8>] (ip_finish_output) from [<c043f948>] (ip_output+0xd8/0xf0)
[<c043f948>] (ip_output) from [<c043f04c>] (ip_local_out_sk+0x44/0x48)
This patch makes mkiss behave like the 6pack driver. 6pack does not
panic. In 6pack.c sp_setup() (same function name here) the values for
dev->hard_header_len and dev->addr_len are set to the same values as in
my mkiss patch.
[ralf@linux-mips.org: Massages original submission to conform to the usual
standards for patch submissions.]
Signed-off-by: Thomas Osterried <thomas@osterried.de> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Kejian Yan [Thu, 9 Feb 2017 11:46:15 +0000 (11:46 +0000)]
net: hns: Fix the device being used for dma mapping during TX
This patch fixes the device being used to DMA map skb->data.
Erroneous device assignment causes the crash when SMMU is enabled.
This happens during TX since buffer gets DMA mapped with device
correspondign to net_device and gets unmapped using the device
related to DSAF.
Signed-off-by: Kejian Yan <yankejian@huawei.com> Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dt-bindings: mtd: add a common label property to all mtd devices
This can be used to easily identify a specific chip on a system with
multiple chips.
Signed-off-by: Cédric Le Goater <clg@kaod.org> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
mtd: name the mtd device with an optional label property
This can be used to easily identify a specific chip on a system with
multiple chips.
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Brian Norris [Fri, 10 Feb 2017 18:05:51 +0000 (10:05 -0800)]
Merge tag 'spi-nor/for-4.11-v2' of git://github.com/spi-nor/linux
From Cyrille:
"""
This pull request contains the following notable changes:
- add support to the 4-byte address instruction set.
- add support to new memory parts.
- add support to S3AN memories.
- add support to the Intel SPI controller.
- add support to the Aspeed AST2400 and AST2550 controllers.
- fix max SPI transfer and message sizes in m25p80_read().
- fix the Candence QSPI driver.
- fix the Freescale QSPI driver.
"""
physmap_of sort of depends on the gemini and versatile modules (when
they're enabled), but this isn't expressed in Kconfig. Let's just merge
the modules all together, when enabled. Then we can avoid exporting a
few symbols, and the versatile and gemini code can now be modular again
(the below commit accidentally made them built-in only).
Colin Ian King [Tue, 31 Jan 2017 15:53:17 +0000 (15:53 +0000)]
mtd: spi-nor: cqspi: remove redundant dead code on error return check
Checking for ret < 0 is redundant because a previous check on ret
being non-zero already handles the ret < 0 case. Remove the redundant
code. Found by CoverityScan, CID#1398863, CID#1398864
Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Richard Weinberger <richard@nod.at> Acked-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Yunhui Cui [Thu, 18 Aug 2016 07:37:57 +0000 (15:37 +0800)]
mtd: fsl-quadspi: Rename SEQID_QUAD_READ to SEQID_READ
There are some read modes for flash, such as NORMAL, FAST,
QUAD, DDR QUAD. These modes will use the identical lut table base
So rename SEQID_QUAD_READ to SEQID_READ.
Signed-off-by: Yunhui Cui <B56489@freescale.com> Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com> Acked-by: Han xu <han.xu@nxp.com> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Yunhui Cui [Thu, 18 Aug 2016 07:37:56 +0000 (15:37 +0800)]
mtd:fsl-quadspi:use the property fields of SPI-NOR
We can get the read/write/erase opcode from the spi nor framework
directly. This patch uses the information stored in the SPI-NOR to
remove the hardcode in the fsl_qspi_init_lut().
Signed-off-by: Yunhui Cui <B56489@freescale.com> Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com> Acked-by: Han xu <han.xu@nxp.com> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Cédric Le Goater [Thu, 19 Jan 2017 09:13:18 +0000 (10:13 +0100)]
mtd: aspeed: fix compile warning in aspeed_smc_read_from_ahb()
The first argument of ioread32_rep() and ioread8_rep is not
const. Change aspeed_smc_read_from_ahb() prototype to fix compile
warning :
drivers/mtd/spi-nor/aspeed-smc.c: In function 'aspeed_smc_read_from_ahb':
drivers/mtd/spi-nor/aspeed-smc.c:212:16: warning: passing argument 1 of 'ioread32_rep' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
ioread32_rep(src, buf, len >> 2);
Signed-off-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Uwe Kleine-König [Tue, 17 Jan 2017 11:03:38 +0000 (12:03 +0100)]
mtd: spi-nor: add dt support for Everspin MRAMs
The MR25 family doesn't support JEDEC, so they need explicit mentioning
in the list of supported spi IDs. This makes it possible to add these
using for example:
compatible = "everspin,mr25h40";
There was already an entry for mr25h256. Move that one out of the "keep
for compatibility" section and put in a new group for Everspin MRAMs.
Cyrille Pitchen [Thu, 27 Oct 2016 10:03:57 +0000 (12:03 +0200)]
mtd: spi-nor: add a stateless method to support memory size above 128Mib
This patch provides an alternative mean to support memory above 16MiB
(128Mib) by replacing 3byte address op codes by their associated 4byte
address versions.
Using the dedicated 4byte address op codes doesn't change the internal
state of the SPI NOR memory as opposed to using other means such as
updating a Base Address Register (BAR) and sending command to enter/leave
the 4byte mode.
Hence when a CPU reset occurs, early bootloaders don't need to be aware
of BAR value or 4byte mode being enabled: they can still access the first
16MiB of the SPI NOR memory using the regular 3byte address op codes.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Tested-by: Vignesh R <vigneshr@ti.com> Acked-by: Marek Vasut <marek.vasut@gmail.com>
Cyrille Pitchen [Thu, 27 Oct 2016 09:55:39 +0000 (11:55 +0200)]
mtd: spi-nor: rename SPINOR_OP_* macros of the 4-byte address op codes
This patch renames the SPINOR_OP_* macros of the 4-byte address
instruction set so the new names all share a common pattern: the 4-byte
address name is built from the 3-byte address name appending the "_4B"
suffix.
The patch also introduces new op codes to support other SPI protocols such
as SPI 1-4-4 and SPI 1-2-2.
This is a transitional patch and will help a later patch of spi-nor.c
to automate the translation from the 3-byte address op codes into their
4-byte address version.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Acked-by: Mark Brown <broonie@kernel.org> Acked-by: Marek Vasut <marek.vasut@gmail.com>
Cédric Le Goater [Wed, 21 Dec 2016 16:57:17 +0000 (17:57 +0100)]
mtd: spi-nor: add memory controllers for the Aspeed AST2500 SoC
This driver adds mtd support for the Aspeed AST2500 SoC static memory
controllers :
* Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. supports SPI type flash memory (CE0-CE1)
. CE2 can be of NOR type flash but this is not supported by the
driver
Each controller has a memory range on which it maps its flash module
slaves. Each slave is assigned a memory window for its mapping that
can be changed at bootime with the Segment Address Register.
Each SPI flash slave can then be accessed in two modes: Command and
User. When in User mode, accesses to the memory segment of the slaves
are translated in SPI transfers. When in Command mode, the HW
generates the SPI commands automatically and the memory segment is
accessed as if doing a MMIO.
Currently, only the User mode is supported. Command mode needs a
little more work to check that the memory window on the AHB bus fits
the module size.
Based on previous work from Milton D. Miller II <miltonm@us.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Cyrille Pitchen [Tue, 6 Dec 2016 17:14:24 +0000 (18:14 +0100)]
mtd: spi-nor: remove WARN_ONCE() message in spi_nor_write()
This patch removes the WARN_ONCE() test in spi_nor_write().
This macro triggers the display of a warning message almost every time we
use a UBI file-system because a write operation is performed at offset 64,
which is in the middle of the SPI NOR memory page. This is a valid
operation for ubifs.
Hence this warning is pretty annoying and useless so we just remove it.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Suggested-by: Richard Weinberger <richard@nod.at> Suggested-by: Andras Szemzo <szemzo.andras@gmail.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cyrille Pitchen [Tue, 6 Dec 2016 16:01:41 +0000 (17:01 +0100)]
mtd: spi-nor: improve macronix_quad_enable()
The patch checks whether the Quad Enable bit is already set in the Status
Register. If so, the function exits immediately with a successful return
code.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Acked-by: Marek Vasut <marek.vasut@gmail.com>
Andrey Ryabinin [Fri, 10 Feb 2017 09:54:05 +0000 (12:54 +0300)]
x86/mm/ptdump: Fix soft lockup in page table walker
CONFIG_KASAN=y needs a lot of virtual memory mapped for its shadow.
In that case ptdump_walk_pgd_level_core() takes a lot of time to
walk across all page tables and doing this without
a rescheduling causes soft lockups:
Thomas Gleixner [Thu, 9 Feb 2017 15:08:42 +0000 (16:08 +0100)]
x86/tsc: Make the TSC ADJUST sanitizing work for tsc_reliable
When the TSC is marked reliable then the synchronization check is skipped,
but that also skips the TSC ADJUST sanitizing code. So on a machine with a
wreckaged BIOS the TSC deviation between CPUs might go unnoticed.
Let the TSC adjust sanitizing code run unconditionally and just skip the
expensive synchronization checks when TSC is marked reliable.
Thomas Gleixner [Thu, 9 Feb 2017 15:08:41 +0000 (16:08 +0100)]
x86/tsc: Avoid the large time jump when sanitizing TSC ADJUST
Olof reported that on a machine which has a BIOS wreckaged TSC the
timestamps in dmesg are making a large jump because the TSC value is
jumping forward after resetting the TSC ADJUST register to a sane value.
This can be avoided by calling the TSC ADJUST saniziting function before
initializing the per cpu sched clock machinery. That takes the offset into
account and avoid the time jump.
What cannot be avoided is that the 'Firmware Bug' warnings on the secondary
CPUs are printed with the large time offsets because it would be too much
effort and ugly hackery to print those warnings into a buffer and emit them
after the adjustemt on the starting CPUs. It's a firmware bug and should be
fixed in firmware. The weird timestamps are collateral damage and just
illustrate the sillyness of the BIOS folks:
Reported-by: Olof Johansson <olof@lixom.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20170209151231.411460506@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
tick/nohz: Fix possible missing clock reprog after tick soft restart
ts->next_tick keeps track of the next tick deadline in order to optimize
clock programmation on irq exit and avoid redundant clock device writes.
Now if ts->next_tick missed an update, we may spuriously miss a clock
reprog later as the nohz code is fooled by an obsolete next_tick value.
This is what happens here on a specific path: when we observe an
expired timer from the nohz update code on irq exit, we perform a soft
tick restart which simply fires the closest possible tick without
actually exiting the nohz mode and restoring a periodic state. But we
forget to update ts->next_tick accordingly.
As a result, after the next tick resulting from such soft tick restart,
the nohz code sees a stale value on ts->next_tick which doesn't match
the clock deadline that just expired. If that obsolete ts->next_tick
value happens to collide with the actual next tick deadline to be
scheduled, we may spuriously bypass the clock reprogramming. In the
worst case, the tick may never fire again.
Fix this with a ts->next_tick reset on soft tick restart.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reviewed: Wanpeng Li <wanpeng.li@hotmail.com> Acked-by: Rik van Riel <riel@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1486485894-29173-1-git-send-email-fweisbec@gmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Peter Zijlstra [Tue, 31 Jan 2017 10:27:10 +0000 (11:27 +0100)]
perf/core: Fix crash in perf_event_read()
Alexei had his box explode because doing read() on a package
(rapl/uncore) event that isn't currently scheduled in ends up doing an
out-of-bounds load.
Rework the code to more explicitly deal with event->oncpu being -1.
Rafał Miłecki [Tue, 10 Jan 2017 22:15:24 +0000 (23:15 +0100)]
mtd: bcm47xxpart: move TRX parsing code to separated function
This change simplifies main parsing loop logic a bit. In future it may
be useful for moving TRX support to separated module / parser (if we
implement support for them at some point).
Finally parsing TRX at the end puts us in a better position as we have
better flash layout knowledge. It may be useful e.g. if it appears there
is more than 1 TRX partition.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
J. Bruce Fields [Thu, 9 Feb 2017 19:20:42 +0000 (14:20 -0500)]
nfsd: Revert "nfsd: special case truncates some more"
This patch incorrectly attempted nested mnt_want_write, and incorrectly
disabled nfsd's owner override for truncate. We'll fix those problems
and make another attempt soon, for the moment I think the safest is to
revert.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Linus Torvalds [Fri, 10 Feb 2017 01:46:30 +0000 (17:46 -0800)]
Merge tag 'drm-fixes-for-v4.10-rc8' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"This should be the final set of drm fixes for 4.10: one vmwgfx boot
fix, one vc4 fix, and a few i915 fixes:
* tag 'drm-fixes-for-v4.10-rc8' of git://people.freedesktop.org/~airlied/linux:
drm: vc4: adapt to new behaviour of drm_crtc.c
drm/i915: Always convert incoming exec offsets to non-canonical
drm/i915: Remove overzealous fence warn on runtime suspend
drm/i915/bxt: Add MST support when do DPLL calculation
drm/i915: don't warn about Skylake CPU - KabyPoint PCH combo
drm/i915: fix i915 running as dom0 under Xen
drm/i915: Flush untouched framebuffers before display on !llc
drm/i915: fix use-after-free in page_flip_completed()
drm/vmwgfx: Fix depth input into drm_mode_legacy_fb_format
Steffen Maier [Wed, 8 Feb 2017 14:34:22 +0000 (15:34 +0100)]
scsi: zfcp: fix use-after-free by not tracing WKA port open/close on failed send
Dan Carpenter kindly reported:
<quote>
The patch d27a7cb91960: "zfcp: trace on request for open and close of
WKA port" from Aug 10, 2016, leads to the following static checker
warning:
drivers/s390/scsi/zfcp_fsf.c:1615 zfcp_fsf_open_wka_port()
warn: 'req' was already freed.
1613 out:
1614 spin_unlock_irq(&qdio->req_q_lock);
1615 if (req && !IS_ERR(req))
1616 zfcp_dbf_rec_run_wka("fsowp_1", wka_port, req->req_id);
^^^^^^^^^^^
Use after free.
1617 return retval;
1618 }
Same thing for zfcp_fsf_close_wka_port() as well.
</quote>
Rather than relying on req being NULL (or ERR_PTR) for all cases where
we don't want to trace or should not trace,
simply check retval which is unconditionally initialized with -EIO != 0
and it can only become 0 on successful retval = zfcp_fsf_req_send(req).
With that we can also remove the then again unnecessary unconditional
initialization of req which was introduced with that earlier commit.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Suggested-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Fixes: d27a7cb91960 ("zfcp: trace on request for open and close of WKA port") Cc: <stable@vger.kernel.org> #2.6.38+ Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Reviewed-by: Jens Remus <jremus@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dave Carroll [Thu, 9 Feb 2017 18:04:47 +0000 (11:04 -0700)]
scsi: aacraid: Fix INTx/MSI-x issue with older controllers
commit 78cbccd3bd68 ("aacraid: Fix for KDUMP driver hang")
caused a problem on older controllers which do not support MSI-x (namely
ASR3405,ASR3805). This patch conditionalizes the previous patch to
controllers which support MSI-x
Cc: <stable@vger.kernel.org> # v4.7+ Fixes: 78cbccd3bd68 ("aacraid: Fix for KDUMP driver hang") Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com> Signed-off-by: Dave Carroll <david.carroll@microsemi.com> Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dave Airlie [Fri, 10 Feb 2017 00:14:24 +0000 (10:14 +1000)]
Merge tag 'drm-intel-fixes-2017-02-09' of git://anongit.freedesktop.org/git/drm-intel into drm-fixes
Hopefully final fixes for v4.10, about half of them stable material.
* tag 'drm-intel-fixes-2017-02-09' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Always convert incoming exec offsets to non-canonical
drm/i915: Remove overzealous fence warn on runtime suspend
drm/i915/bxt: Add MST support when do DPLL calculation
drm/i915: don't warn about Skylake CPU - KabyPoint PCH combo
drm/i915: fix i915 running as dom0 under Xen
drm/i915: Flush untouched framebuffers before display on !llc
drm/i915: fix use-after-free in page_flip_completed()
USB PHYs need the MDIO clock divisor enabled earlier to work.
Initialize mdio clock divisor in probe function. The ext bus
bit available in the same register will be used by mdio mux
to enable external mdio.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com> Fixes: ddc24ae1 ("net: phy: Broadcom iProc MDIO bus driver") Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jon Mason <jon.mason@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Wed, 8 Feb 2017 13:16:45 +0000 (21:16 +0800)]
igmp, mld: Fix memory leak in igmpv3/mld_del_delrec()
In function igmpv3/mld_add_delrec() we allocate pmc and put it in
idev->mc_tomb, so we should free it when we don't need it in del_delrec().
But I removed kfree(pmc) incorrectly in latest two patches. Now fix it.
Fixes: 24803f38a5c0 ("igmp: do not remove igmp souce list info when ...") Fixes: 1666d49e1d41 ("mld: do not remove mld souce list info when ...") Reported-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ross Lagerwall [Wed, 8 Feb 2017 10:57:37 +0000 (10:57 +0000)]
xen-netfront: Improve error handling during initialization
This fixes a crash when running out of grant refs when creating many
queues across many netdevs.
* If creating queues fails (i.e. there are no grant refs available),
call xenbus_dev_fatal() to ensure that the xenbus device is set to the
closed state.
* If no queues are created, don't call xennet_disconnect_backend as
netdev->real_num_tx_queues will not have been set correctly.
* If setup_netfront() fails, ensure that all the queues created are
cleaned up, not just those that have been set up.
* If any queues were set up and an error occurs, call
xennet_destroy_queues() to clean up the napi context.
* If any fatal error occurs, unregister and destroy the netdev to avoid
leaving around a half setup network device.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 9 Feb 2017 21:41:43 +0000 (16:41 -0500)]
Merge branch 'sierra_net-fixes'
Stefan Brüns says:
====================
Fixes for sierra_net driver
When trying to initiate a dual-stack (ipv4v6) connection, a MC7710, FW
version SWI9200X_03.05.24.00ap answers with an unsupported LSI. Add support
for this LSI.
Also the link_type should be ignored when going idle, otherwise the modem
is stuck in a bad link state.
Tested on MC7710, T-Mobile DE, APN internet.telekom, IPv4v6 PDP type. Both
IPv4 and IPv6 connections work.
v2: Do not overwrite protocol field in rx_fixup
v3: Remove leftover struct ethhdr *eth declaration
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Brüns [Wed, 8 Feb 2017 01:46:33 +0000 (02:46 +0100)]
sierra_net: Skip validating irrelevant fields for IDLE LSIs
When the context is deactivated, the link_type is set to 0xff, which
triggers a warning message, and results in a wrong link status, as
the LSI is ignored.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Brüns [Wed, 8 Feb 2017 01:46:32 +0000 (02:46 +0100)]
sierra_net: Add support for IPv6 and Dual-Stack Link Sense Indications
If a context is configured as dualstack ("IPv4v6"), the modem indicates
the context activation with a slightly different indication message.
The dual-stack indication omits the link_type (IPv4/v6) and adds
additional address fields.
IPv6 LSIs are identical to IPv4 LSIs, but have a different link type.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Reviewed-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
when calling syscall(__NR_write, sock2, 0x208aaf27ul, 0x0ul) on a KCM
seqpacket socket. It appears that kcm_sendmsg() does not handle len==0
case correctly, which causes an empty skb is allocated and queued.
Fix this by skipping the skb allocation for len==0 case.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Tom Herbert <tom@herbertland.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
xen-netfront: Rework the fix for Rx stall during OOM and network stress
The commit 90c311b0eeea ("xen-netfront: Fix Rx stall during network
stress and OOM") caused the refill timer to be triggerred almost on
all invocations of xennet_alloc_rx_buffers for certain workloads.
This reworks the fix by reverting to the old behaviour and taking into
consideration the skb allocation failure. Refill timer is now triggered
on insufficient requests or skb allocation failure.
Signed-off-by: Vineeth Remanan Pillai <vineethp@amazon.com> Fixes: 90c311b0eeea (xen-netfront: Fix Rx stall during network stress and OOM) Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pull SCSI target fixes from Nicholas Bellinger:
"This target series for v4.10 contains fixes which address a few
long-standing bugs that DATERA's QA + automation teams have uncovered
while putting v4.1.y target code into production usage.
We've been running the top three in our nightly automated regression
runs for the last two months, and the COMPARE_AND_WRITE fix Mr. Gary
Guo has been manually verifying against a four node ESX cluster this
past week.
Note all of them have CC' stable tags.
Summary:
- Fix a bug with ESX EXTENDED_COPY + SAM_STAT_RESERVATION_CONFLICT
status, where target_core_xcopy.c logic was incorrectly returning
SAM_STAT_CHECK_CONDITION for all non SAM_STAT_GOOD cases (Nixon
Vincent)
- Fix a TMR LUN_RESET hung task bug while other in-flight TMRs are
being aborted, before the new one had been dispatched into tmr_wq
(Rob Millner)
- Fix a long standing double free OOPs, where a dynamically generated
'demo-mode' NodeACL has multiple sessions associated with it, and
the /sys/kernel/config/target/$FABRIC/$WWN/ subsequently disables
demo-mode, but never converts the dynamic ACL into a explicit ACL
(Rob Millner)
- Fix a long standing reference leak with ESX VAAI COMPARE_AND_WRITE
when the second phase WRITE COMMIT command fails, resulting in
CHECK_CONDITION response never being sent and se_cmd->cmd_kref
never reaching zero (Gary Guo)
Beyond these items on v4.1.y we've reproduced, fixed, and run through
our regression test suite using iscsi-target exports, there are two
additional outstanding list items:
- Remove a >= v4.2 RCU conversion BUG_ON that would trigger when
dynamic node NodeACLs where being converted to explicit NodeACLs.
The patch drops the BUG_ON to follow how pre RCU conversion worked
for this special case (Benjamin Estrabaud)
- Add ibmvscsis target_core_fabric_ops->max_data_sg_nent assignment
to match what IBM's Virtual SCSI hypervisor is already enforcing at
transport layer. (Bryant Ly + Steven Royer)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
ibmvscsis: Add SGL limit
target: Fix COMPARE_AND_WRITE ref leak for non GOOD status
target: Fix multi-session dynamic se_node_acl double free OOPs
target: Fix early transport_generic_handle_tmr abort scenario
target: Use correct SCSI status during EXTENDED_COPY exception
target: Don't BUG_ON during NodeACL dynamic -> explicit conversion
net: phy: Fix PHY module checks and NULL deref in phy_attach_direct()
The Generic PHY drivers gets assigned after we checked that the current
PHY driver is NULL, so we need to check a few things before we can
safely dereference d->driver. This would be causing a NULL deference to
occur when a system binds to the Generic PHY driver. Update
phy_attach_direct() to do the following:
- grab the driver module reference after we have assigned the Generic
PHY drivers accordingly, and remember we came from the generic PHY
path
- update the error path to clean up the module reference in case the
Generic PHY probe function fails
- split the error path involving phy_detacht() to avoid double free/put
since phy_detach() does all the clean up
- finally, have phy_detach() drop the module reference count before we
call device_release_driver() for the Generic PHY driver case
Fixes: cafe8df8b9bc ("net: phy: Fix lack of reference count on PHY driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 9 Feb 2017 19:58:05 +0000 (11:58 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A fix for a crash in uinput, and a fix for build errors when HID-RMI
is built-in but SERIO is a module"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - select 'SERIO' when needed
Input: uinput - fix crash when mixing old and new init style
Brian Norris [Thu, 9 Feb 2017 06:44:44 +0000 (22:44 -0800)]
pstore: don't OOPS when there are no ftrace zones
We'll OOPS in ramoops_get_next_prz() if the platform didn't ask for any
ftrace zones (i.e., cxt->fprzs will be NULL). Let's just skip this
entire FTRACE section if there's no 'fprzs'.
Regression seen on a coreboot/depthcharge-based Chromebook.
Fixes: 2fbea82bbb89 ("pstore: Merge per-CPU ftrace records into one") Cc: Joel Fernandes <joelaf@google.com> Cc: Kees Cook <keescook@chromium.org> Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kees Cook <keescook@chromium.org>
powerpc/powernv: Fix CPU hotplug to handle waking on HVI
The IPIs come in as HVI not EE, so we need to test the appropriate
SRR1 bits. The encoding is such that it won't have false positives
on P7 and P8 so we can just test it like that. We also need to handle
the icp-opal variant of the flush.
Fixes: d74361881f0d ("powerpc/xics: Add ICP OPAL backend") Cc: stable@vger.kernel.org # v4.8+ Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm/radix: Update ERAT flushes when invalidating TLB
Three tiny changes to the ERAT flushing logic: First don't make
it depend on DD1. It hasn't been decided yet but we might run
DD2 in a mode that also requires explicit flushes for performance
reasons so make it unconditional. We also add a missing isync, and
finally remove the flush from _tlbiel_va as it is only necessary
for congruence-class invalidations (PID, LPID and full TLB), not
targetted invalidations.
Fixes: 96ed1fe511a8 ("powerpc/mm/radix: Invalidate ERAT on tlbiel for POWER9 DD1") Cc: stable@vger.kernel.org # v4.9+ Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gabriel C reports that it causes his machine to not boot, and we haven't
tracked down the reason for it yet. Since the bug it fixes has been
around for a longish time, we're better off reverting the fix for now.
Gabriel says:
"It hangs early and freezes with a lot RCU warnings.
The box is a PRIMERGY TX200 S5 , 2 socket , 2 x E5520 CPU(s) installed"
and Ruslan and Thomas are currently stumped.
Reported-and-bisected-by: Gabriel C <nix.or.die@gmail.com> Cc: Ruslan Ruslichenko <rruslich@cisco.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@kernel.org # for the backport of the original commit Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 9 Feb 2017 00:06:10 +0000 (16:06 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge fixes from Andrew Morton:
"4 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/slub.c: fix random_seq offset destruction
cpumask: use nr_cpumask_bits for parsing functions
mm: avoid returning VM_FAULT_RETRY from ->page_mkwrite handlers
kernel/ucount.c: mark user_header with kmemleak_ignore()
Bail out early from init_cache_random_seq if s->random_seq is already
initialised. This prevents destroying the previously computed
random_seq offsets later in the function.
If the offsets are destroyed, then shuffle_freelist will truncate
page->freelist to just the first object (orphaning the rest).
Fixes: 210e7a43fa90 ("mm: SLUB freelist randomization") Link: http://lkml.kernel.org/r/20170207140707.20824-1-sean@erifax.org Signed-off-by: Sean Rees <sean@erifax.org> Reported-by: <userwithuid@gmail.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Thomas Garnier <thgarnie@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tejun Heo [Wed, 8 Feb 2017 22:30:56 +0000 (14:30 -0800)]
cpumask: use nr_cpumask_bits for parsing functions
Commit 513e3d2d11c9 ("cpumask: always use nr_cpu_ids in formatting and
parsing functions") converted both cpumask printing and parsing
functions to use nr_cpu_ids instead of nr_cpumask_bits. While this was
okay for the printing functions as it just picked one of the two output
formats that we were alternating between depending on a kernel config,
doing the same for parsing wasn't okay.
nr_cpumask_bits can be either nr_cpu_ids or NR_CPUS. We can always use
nr_cpu_ids but that is a variable while NR_CPUS is a constant, so it can
be more efficient to use NR_CPUS when we can get away with it.
Converting the printing functions to nr_cpu_ids makes sense because it
affects how the masks get presented to userspace and doesn't break
anything; however, using nr_cpu_ids for parsing functions can
incorrectly leave the higher bits uninitialized while reading in these
masks from userland. As all testing and comparison functions use
nr_cpumask_bits which can be larger than nr_cpu_ids, the parsed cpumasks
can erroneously yield false negative results.
This made the taskstats interface incorrectly return -EINVAL even when
the inputs were correct.
Fix it by restoring the parse functions to use nr_cpumask_bits instead
of nr_cpu_ids.
Link: http://lkml.kernel.org/r/20170206182442.GB31078@htj.duckdns.org Fixes: 513e3d2d11c9 ("cpumask: always use nr_cpu_ids in formatting and parsing functions") Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Martin Steigerwald <martin.steigerwald@teamix.de> Debugged-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Cc: <stable@vger.kernel.org> [4.0+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kara [Wed, 8 Feb 2017 22:30:53 +0000 (14:30 -0800)]
mm: avoid returning VM_FAULT_RETRY from ->page_mkwrite handlers
Some ->page_mkwrite handlers may return VM_FAULT_RETRY as its return
code (GFS2 or Lustre can definitely do this). However VM_FAULT_RETRY
from ->page_mkwrite is completely unhandled by the mm code and results
in locking and writeably mapping the page which definitely is not what
the caller wanted.
Fix Lustre and block_page_mkwrite_ret() used by other filesystems
(notably GFS2) to return VM_FAULT_NOPAGE instead which results in
bailing out from the fault code, the CPU then retries the access, and we
fault again effectively doing what the handler wanted.
Link: http://lkml.kernel.org/r/20170203150729.15863-1-jack@suse.cz Signed-off-by: Jan Kara <jack@suse.cz> Reported-by: Al Viro <viro@ZenIV.linux.org.uk> Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com> Cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The BUG_ON()s are intended to crash so no need to clean up after
ourselves on error there. This is also a kernel/ subsys_init() we don't
need a respective exit call here as this is never modular, so just white
list it.
Link: http://lkml.kernel.org/r/20170203211404.31458-1-mcgrof@kernel.org Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Kees Cook <keescook@chromium.org> Cc: Nikolay Borisov <n.borisov.lkml@gmail.com> Cc: Serge Hallyn <serge@hallyn.com> Cc: Jan Kara <jack@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rafał Miłecki [Wed, 8 Feb 2017 22:53:44 +0000 (23:53 +0100)]
mtd: bcm47xxsflash: support reading flash out of mapping window
For reading flash content we use MMIO but it's possible to read only
first 16 MiB this way. It's simply an arch design/limitation.
To support flash sizes bigger than 16 MiB implement indirect access
using ChipCommon registers.
This has been tested using MX25L25635F.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Brian Norris [Wed, 8 Feb 2017 23:00:24 +0000 (15:00 -0800)]
Merge tag 'nand/for-4.11' of github.com:linux-nand/linux
From Boris:
"""
This pull request contains minor fixes/improvements on existing drivers:
- sunxi: avoid busy-waiting for NAND events
- ifc: fix ECC handling on IFC v1.0
- OX820: add explicit dependency on ARCH_OXNAS in Kconfig
- core: add a new manufacture ID and fix a kernel-doc warning
- fsmc: kill pdata support
- lpc32xx_slc: remove unneeded NULL check
"""
Conflicts:
include/linux/mtd/nand.h
[Brian: trivial conflict in the comment section]
Zach Brown [Tue, 10 Jan 2017 19:30:21 +0000 (13:30 -0600)]
mtd: nand: set max_bb_per_die and blocks_per_die for ONFI compliant chips
ONFI compliant chips contain the values for the max_bb_per_die and
blocks_per_die fields in the parameter page. When the ONFI paged is
retrieved/parsed the chip's fields are set by the corresponding fields
in the param page.
Signed-off-by: Zach Brown <zach.brown@ni.com> Acked-by: Boris Brezillon <boris.brezillon@free-electron.com> Acked-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Zach Brown [Tue, 10 Jan 2017 19:30:20 +0000 (13:30 -0600)]
mtd: nand: implement 'max_bad_blocks' mtd function
Implement the new mtd function 'max_bad_blocks'. Using the chip's
max_bb_per_die and blocks_per_die fields to determine the maximum bad
blocks to reserve for an MTD.
Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com> Signed-off-by: Zach Brown <zach.brown@ni.com> Acked-by: Boris Brezillon <boris.brezillon@free-electron.com> Acked-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Zach Brown [Tue, 10 Jan 2017 19:30:19 +0000 (13:30 -0600)]
mtd: nand: Add max_bb_per_die and blocks_per_die fields to nand_chip
The fields max_bb_per_die and blocks_per_die are useful determining the
number of bad blocks a MTD needs to allocate. How they are set will
depend on if the chip is ONFI, JEDEC or a full-id entry in the nand_ids
table.
Signed-off-by: Zach Brown <zach.brown@ni.com> Acked-by: Boris Brezillon <boris.brezillon@free-electron.com> Acked-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When drm_crtc_init_with_planes() was orignally added
(in drm_crtc.c, e13161af80c185ecd8dc4641d0f5df58f9e3e0af
drm: Add drm_crtc_init_with_planes() (v2)), it only checked for "primary"
being non-null. If that was the case, it modified primary->possible_crtcs.
Then, when support for cursor planes was added
(fc1d3e44ef7c1db93384150fdbf8948dcf949f15 drm: Allow drivers to register
cursor planes with crtc), the same behaviour was implemented for cursor
planes.
vc4_plane_init() since its inception has passed 0xff as "possible_crtcs"
parameter to drm_universal_plane_init(). With a change in drm_crtc.c
(7abc7d47510c75dd984380ebf819616e574c9604 drm: don't override
possible_crtcs for primary/cursor planes) passing 0xff results in primary's
possible_crtcs set to 0xff (cursor was updated manually by vc4_crtc.c).
Consequently, it would be allowed to use the primary plane from CRTC 1 (for
example) on CRTC 0, which would result in the overlay and cursors being
buried.
Arnd Bergmann [Mon, 24 Oct 2016 15:28:35 +0000 (17:28 +0200)]
mtd: ichxrom: maybe-uninitialized with gcc-4.9
pci_read_config_word() might fail and not initialize its output,
as pointed out by older versions of gcc when using the -Wmaybe-unintialized
flag:
drivers/mtd/maps/ichxrom.c: In function ‘ichxrom_cleanup’:
drivers/mtd/maps/ichxrom.c:63:2: error: ‘word’ is used uninitialized in this function [-Werror=uninitialized]
This is apparently a correct warning, though it does not show up
with newer compilers. Changing the code to not attempt to write
back uninitialized data into PCI config space is a correct
fix for the problem and avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Jeff Westfahl [Tue, 10 Jan 2017 19:30:17 +0000 (13:30 -0600)]
mtd: introduce function max_bad_blocks
If implemented, 'max_bad_blocks' returns the maximum number of bad
blocks to reserve for a MTD. An implementation for NAND is coming soon.
Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com> Signed-off-by: Zach Brown <zach.brown@ni.com> Acked-by: Boris Brezillon <boris.brezillon@free-electron.com> Acked-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Arnd Bergmann [Fri, 3 Feb 2017 09:49:17 +0000 (10:49 +0100)]
mtd: pmcmsp: use kstrndup instead of kmalloc+strncpy
kernelci.org reports a warning for this driver, as it copies a local
variable into a 'const char *' string:
drivers/mtd/maps/pmcmsp-flash.c:149:30: warning: passing argument 1 of 'strncpy' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
Using kstrndup() simplifies the code and avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Linus Walleij [Sat, 28 Jan 2017 21:50:48 +0000 (22:50 +0100)]
mtd: physmap_of: add a hook for Gemini flash probing
In order to support device tree probing of Gemini NOR flash
chips, a certain register in the syscon needs to be poked
to enable parallel flash mode.
Such things used to happen in "necessarily different" board
file code, and this indeed was also done for the Gemini, so
the MTD driver could treat it as any memory-mapped NOR flash,
but this is not the way in the future: board files need to
go, and hardware concerns distributed down to the applicable
drivers.
This adds a hook in the same way that the Versatile did: if
the Kconfig symbol is not selected the net total of supporting
Gemini should be zero bytes of added code. To live up to this
promise, also the return value error print from the Versatile
extra probe call get to be removed in this patch, all printing
need to happen in the add-ons.
Cc: Janos Laube <janos.dev@gmail.com> Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com> Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
projects / mirror_ubuntu-jammy-kernel.git / log