drivers: net: cpsw: ethtool: fix accessing to suspended device
BugLink: http://bugs.launchpad.net/bugs/1625177
The CPSW might be suspended by RPM if all ethX interfaces are down,
but it still could be accesible through ethtool interfce. In this case
ethtool operations, requiring registers access, will cause L3 errors and
CPSW crash.
ethtool callbcaks which need to access CPSW registers now:
.set_coalesce(), .get_ethtool_stats(), .set_pauseparam(), .get_regs()
Hence, fix it by adding .begin()/.complete() ethtool callbacks, which
will be called before/after each ethtool operation runs, and do CPSW
RPM handling in these callbacks. That way CPSW will be active while
handling ethtool requests.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 7898b1daf055537a8f661828272defecdee49f27) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
drivers: net: cpsw: remove pm runtime calls from suspend callbacks
BugLink: http://bugs.launchpad.net/bugs/1625177
PM runtime is properly handled in cpsw_ndo_open/stop(), as result it
isn't required to duplicate these calls in .suspend()/.resume()
callbacks. Moreover, it might cause unnecessary RPM resume of CPSW
during System suspend in the case it's already suspended because
all ethX interfaces are down already, before System suspend started.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 74556f516702331444b3c2d900a6a1d1fc9fc4cd) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 108a653730e4c654bd0815276276e59ea0d64578) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
drivers: net: cpsw: fix wrong regs access in cpsw_ndo_open
BugLink: http://bugs.launchpad.net/bugs/1625177
The cpsw_ndo_open() could try to access CPSW registers before
calling pm_runtime_get_sync(). This will trigger L3 error:
WARNING: CPU: 0 PID: 21 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x220/0x34c() 44000000.ocp:L3 Custom Error: MASTER M2 (64-bit) TARGET L4_FAST (Idle): Data Access in Supervisor mode during Functional access
and CPSW will stop functioning.
Hence, fix it by moving pm_runtime_get_sync() before the first access
to CPSW registers in cpsw_ndo_open().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 3fa88c51c73a67e7eeda1fcafd809f9185790b31) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
drivers: net: cpsw: fix suspend when all ethX devices are down
BugLink: http://bugs.launchpad.net/bugs/1625177
The cpsw_suspend() could trigger L3 error and CPSW will stop
functioning if System enters suspend when all ethX net-devices are
down - in this case CPSW could be already suspended by PM runtime, but
cpsw_suspend() will try to call soft_reset_slave() unconditionally
and access CPSW registers.
Hence, fix it by moving soft_reset_slave() from cpsw_suspend() to
cpsw_slave_stop(). This way slave ports will be reset when CPSW is
active and will be in proper state during Suspend.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 1f95ba000c92cafccea007129d40532a4f35b1a6) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Andrea Gelmini [Sat, 21 May 2016 11:50:25 +0000 (13:50 +0200)]
ARM: OMAP2+: Fix typo in omap_device.c
BugLink: http://bugs.launchpad.net/bugs/1625177 Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
(cherry picked from commit f733e7c0e0c2ccdccbc328f31376282725b5d545) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Tony Lindgren [Fri, 12 Feb 2016 16:56:52 +0000 (08:56 -0800)]
ARM: OMAP2+: Fix omap_device for module reload on PM runtime forbid
BugLink: http://bugs.launchpad.net/bugs/1625177
If a driver PM runtime is disabled via sysfs, and the module is
unloaded, PM runtime can't do anything to disable the device. Let's
let the interconnect disable the device on BUS_NOTIFY_UNBOUND_DRIVER.
Otherwise omap_device will produce and error on the following module
reload. This can be easily tested with something like:
Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Nishanth Menon <nm@ti.com> Cc: Rafael J. Wysocki <rafael@kernel.org> Cc: Tero Kristo <t-kristo@ti.com> Reported-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Kevin Hilman <khilman@baylibre.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
(cherry picked from commit cf26f1137333251f3515dea31f95775b99df0fd5) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
ARM: OMAP2+: omap_device: fix crash on omap_device removal
BugLink: http://bugs.launchpad.net/bugs/1625177
Below call chain causes system crash when OMAP device is
removed by calling of_platform_depopulate()/device_del():
Backtrace:
Unable to handle kernel NULL pointer dereference at virtual address 0000000d
pgd = eb100000
[0000000d] *pgd=ad6e1831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
CPU: 1 PID: 1273 Comm: modprobe Not tainted 4.4.15-rt19-00115-ge4d3cd3-dirty #68
Hardware name: Generic DRA74X (Flattened Device Tree)
task: eb1ee800 ti: ec962000 task.ti: ec962000
PC is at omap_device_enable+0x10/0x90
LR is at _od_runtime_resume+0x10/0x24
[...]
[<c00299dc>] (omap_device_enable) from [<c0029a6c>] (_od_runtime_resume+0x10/0x24)
[<c0029a6c>] (_od_runtime_resume) from [<c04ad404>] (__rpm_callback+0x20/0x34)
[<c04ad404>] (__rpm_callback) from [<c04ad438>] (rpm_callback+0x20/0x80)
[<c04ad438>] (rpm_callback) from [<c04aee28>] (rpm_resume+0x48c/0x964)
[<c04aee28>] (rpm_resume) from [<c04af360>] (__pm_runtime_resume+0x60/0x88)
[<c04af360>] (__pm_runtime_resume) from [<c04a4974>] (__device_release_driver+0x30/0x100)
[<c04a4974>] (__device_release_driver) from [<c04a4a60>] (device_release_driver+0x1c/0x28)
[<c04a4a60>] (device_release_driver) from [<c04a38c0>] (bus_remove_device+0xec/0x144)
[<c04a38c0>] (bus_remove_device) from [<c04a0764>] (device_del+0x10c/0x210)
[<c04a0764>] (device_del) from [<c04a67b0>] (platform_device_del+0x18/0x84)
[<c04a67b0>] (platform_device_del) from [<c04a6828>] (platform_device_unregister+0xc/0x20)
[<c04a6828>] (platform_device_unregister) from [<c05adcfc>] (of_platform_device_destroy+0x8c/0x90)
[<c05adcfc>] (of_platform_device_destroy) from [<c04a02f0>] (device_for_each_child+0x4c/0x78)
[<c04a02f0>] (device_for_each_child) from [<c05adc5c>] (of_platform_depopulate+0x30/0x44)
[<c05adc5c>] (of_platform_depopulate) from [<bf123920>] (cpsw_remove+0x68/0xf4 [ti_cpsw])
[<bf123920>] (cpsw_remove [ti_cpsw]) from [<c04a68d8>] (platform_drv_remove+0x24/0x3c)
[<c04a68d8>] (platform_drv_remove) from [<c04a49c8>] (__device_release_driver+0x84/0x100)
[<c04a49c8>] (__device_release_driver) from [<c04a4b20>] (driver_detach+0xac/0xb0)
[<c04a4b20>] (driver_detach) from [<c04a3be8>] (bus_remove_driver+0x60/0xd4)
[<c04a3be8>] (bus_remove_driver) from [<c00d9870>] (SyS_delete_module+0x184/0x20c)
[<c00d9870>] (SyS_delete_module) from [<c0010540>] (ret_fast_syscall+0x0/0x1c)
Code: e3500000e92d40701590630c01a06000 (e5d6300d)
Hence, fix it by using BUS_NOTIFY_REMOVED_DEVICE event for OMAP device
deletion which is sent when DD has finished processing of device
deletion.
Cc: Tony Lindgren <tony@atomide.com> Cc: Tero Kristo <t-kristo@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 213fa10db2f9c6725946cfa682990277eb9cd565) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1625177
Use of_platform_depopulate() in cpsw_remove() instead of
of_device_unregister(), because CSPW child devices will not be
recreated otherwise on next insmod. of_platform_depopulate() is
correct way now as it will ensure that all steps done in
of_platform_populate() are reverted, including cleaning up of
OF_POPULATED flag.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 3bf2cb3ab585bd9ef1e46d3f89619bb33f2391de) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
drivers: net: cpsw: fix wrong regs access in cpsw_remove
BugLink: http://bugs.launchpad.net/bugs/1625177
The L3 error will be generated and system will crash during unloading
of CPSW driver if CPSW is used as module and ethX devices are down.
This happens because CPSW can be power off by PM runtime now when ethX
devices are down.
Hence, ensure that CPSW powered up by PM runtime before performing any
deinitialization actions which require CPSW registers access. In case
of PM runtime error just leave cpsw_remove() as we can't do anything
anymore.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 8a0b6dc958fd1037931b0e01ebf266fbe3c09e92) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
net: ethernet: ti: cpdma: fix lockup in cpdma_ctlr_destroy()
BugLink: http://bugs.launchpad.net/bugs/1625177
Fix deadlock in cpdma_ctlr_destroy() which is triggered now on
cpsw module removal:
cpsw_remove()
- cpdma_ctlr_destroy()
- spin_lock_irqsave(&ctlr->lock, flags)
- cpdma_ctlr_stop()
- spin_lock_irqsave(&ctlr->lock, flags);
- cpdma_chan_destroy()
- spin_lock_irqsave(&ctlr->lock, flags);
The issue has not been observed before because CPDMA channels have
been destroyed manually by CPSW until commit d941ebe88a41 ("net:
ethernet: ti: cpsw: use destroy ctlr to destroy channels") was merged.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit fccd5badb84de03fef9b072e7ae72fe0ea8348e3) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Seth Forshee [Mon, 3 Oct 2016 13:18:03 +0000 (08:18 -0500)]
UBUNTU: SAUCE: (namespace) autofs4: Use real_cred for requestor's ids
BugLink: http://bugs.launchpad.net/bugs/1629204
autofs passes the uid and gid of the user requesting a mount to
userspace, taking them from current->cred. ca6fe3344554 "fs: Call
d_automount with the filesystems creds" causes a regression as
current->cred is now the credentials of real root during automount
and not the credentials of the user. Fix this by taking the ids
from current->real_cred instead.
The device's model download function returns the model data as
an array of u32s, which is later compared to the reference
model data. However, since the latter is an array of u16s,
the comparison does not happen correctly, and model verification
fails. This in turn breaks the POR initialization sequence.
Fixes: 39e7213edc4f3 ("max17042_battery: Support regmap to access device's registers") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Sven Van Asbroeck <TheSven73@googlemail.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
rtree_next_node() walks the linked list of leaf nodes to find the next
block of pages in the struct memory_bitmap. If it walks off the end of
the list of nodes, it walks the list of memory zones to find the next
region of memory. If it walks off the end of the list of zones, it
returns false.
This leaves the struct bm_position's node and zone pointers pointing
at their respective struct list_heads in struct mem_zone_bm_rtree.
memory_bm_find_bit() uses struct bm_position's node and zone pointers
to avoid walking lists and trees if the next bit appears in the same
node/zone. It handles these values being stale.
Swap rtree_next_node()s 'step then test' to 'test-next then step',
this means if we reach the end of memory we return false and leave
the node and zone pointers as they were.
This fixes a panic on resume using AMD Seattle with 64K pages:
[ 6.868732] Freezing user space processes ... (elapsed 0.000 seconds) done.
[ 6.875753] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds)
[ 6.896453] PM: Using 3 thread(s) for decompression.
[ 6.896453] PM: Loading and decompressing image data (5339 pages)...
[ 7.318890] PM: Image loading progress: 0%
[ 7.323395] Unable to handle kernel paging request at virtual address 00800040
[ 7.330611] pgd = ffff000008df0000
[ 7.334003] [00800040] *pgd=00000083fffe0003, *pud=00000083fffe0003, *pmd=00000083fffd0003, *pte=0000000000000000
[ 7.344266] Internal error: Oops: 96000005 [#1] PREEMPT SMP
[ 7.349825] Modules linked in:
[ 7.352871] CPU: 2 PID: 1 Comm: swapper/0 Tainted: G W I 4.8.0-rc1 #4737
[ 7.360512] Hardware name: AMD Overdrive/Supercharger/Default string, BIOS ROD1002C 04/08/2016
[ 7.369109] task: ffff8003c0220000 task.stack: ffff8003c0280000
[ 7.375020] PC is at set_bit+0x18/0x30
[ 7.378758] LR is at memory_bm_set_bit+0x24/0x30
[ 7.383362] pc : [<ffff00000835bbc8>] lr : [<ffff0000080faf18>] pstate: 60000045
[ 7.390743] sp : ffff8003c0283b00
[ 7.473551]
[ 7.475031] Process swapper/0 (pid: 1, stack limit = 0xffff8003c0280020)
[ 7.481718] Stack: (0xffff8003c0283b00 to 0xffff8003c0284000)
[ 7.800075] Call trace:
[ 7.887097] [<ffff00000835bbc8>] set_bit+0x18/0x30
[ 7.891876] [<ffff0000080fb038>] duplicate_memory_bitmap.constprop.38+0x54/0x70
[ 7.899172] [<ffff0000080fcc40>] snapshot_write_next+0x22c/0x47c
[ 7.905166] [<ffff0000080fe1b4>] load_image_lzo+0x754/0xa88
[ 7.910725] [<ffff0000080ff0a8>] swsusp_read+0x144/0x230
[ 7.916025] [<ffff0000080fa338>] load_image_and_restore+0x58/0x90
[ 7.922105] [<ffff0000080fa660>] software_resume+0x2f0/0x338
[ 7.927752] [<ffff000008083350>] do_one_initcall+0x38/0x11c
[ 7.933314] [<ffff000008b40cc0>] kernel_init_freeable+0x14c/0x1ec
[ 7.939395] [<ffff0000087ce564>] kernel_init+0x10/0xfc
[ 7.944520] [<ffff000008082e90>] ret_from_fork+0x10/0x40
[ 7.949820] Code: d28000228b400c21f98000319ac32043 (c85f7c22)
[ 7.955909] ---[ end trace 0024a5986e6ff323 ]---
[ 7.960529] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Here struct mem_zone_bm_rtree's start_pfn has been returned instead of
struct rtree_node's addr as the node/zone pointers are corrupt after
we walked off the end of the lists during mark_unsafe_pages().
This behaviour was exposed by commit 6dbecfd345a6 ("PM / hibernate:
Simplify mark_unsafe_pages()"), which caused mark_unsafe_pages() to call
duplicate_memory_bitmap(), which uses memory_bm_find_bit() after walking
off the end of the memory bitmap.
Fixes: 3a20cb177961 (PM / Hibernate: Implement position keeping in radix tree) Signed-off-by: James Morse <james.morse@arm.com>
[ rjw: Subject ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Restore the processor state before calling any other functions to
ensure per-CPU variables can be used with KASLR memory randomization.
Tracing functions use per-CPU variables (GS based on x86) and one was
called just before restoring the processor state fully. It resulted
in a double fault when both the tracing & the exception handler
functions tried to use a per-CPU variable.
Fixes: bb3632c6101b (PM / sleep: trace events for suspend/resume) Reported-and-tested-by: Borislav Petkov <bp@suse.de> Reported-by: Jiri Kosina <jikos@kernel.org> Tested-by: Rafael J. Wysocki <rafael@kernel.org> Tested-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Thomas Garnier <thgarnie@google.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
cpu_has_fpu macro uses smp_processor_id() and is currently executed
with preemption enabled, that triggers the warning at runtime.
It is assumed throughout the kernel that if any CPU has an FPU, then all
CPUs would have an FPU as well, so it is safe to perform the check with
preemption enabled - change the code to use raw_ variant of the check to
avoid the warning.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14125/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Commit c1a0e9bc885d ("MIPS: Allow compact branch policy to be changed")
added Kconfig entries allowing for the compact branch policy used by the
compiler for MIPSr6 kernels to be specified. This can be useful for
debugging, particularly in systems where compact branches have recently
been introduced.
Unfortunately mainline gcc 5.x supports MIPSr6 but not the
-mcompact-branches compiler flag, leading to MIPSr6 kernels failing to
build with gcc 5.x with errors such as:
Fixing this by hiding the Kconfig entry behind another seems to be more
hassle than it's worth, as MIPSr6 & compact branches have been around
for a while now and if policy does need to be set for debug it can be
done easily enough with KCFLAGS. Therefore remove the compact branch
policy Kconfig entries & their handling in the Makefile.
This reverts commit c1a0e9bc885d ("MIPS: Allow compact branch policy to
be changed").
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Reported-by: kbuild test robot <fengguang.wu@intel.com> Fixes: c1a0e9bc885d ("MIPS: Allow compact branch policy to be changed") Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14241/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The page structures associated with the vDSO pages in the kernel image
are calculated using virt_to_page(), which uses __pa() under the hood to
find the pfn associated with the virtual address. The vDSO data pointers
however point to kernel symbols, so __pa_symbol() should really be used
instead.
Since there is no equivalent to virt_to_page() which uses __pa_symbol(),
fix init_vdso_image() to work directly with pfns, calculated with
__phys_to_pfn(__pa_symbol(...)).
This issue broke the Malta Enhanced Virtual Addressing (EVA)
configuration which has a non-default implementation of __pa_symbol().
This is because it uses a physical alias so that the kernel executes
from KSeg0 (VA 0x80000000 -> PA 0x00000000), while RAM is provided to
the kernel in the KUSeg range (VA 0x00000000 -> PA 0x80000000) which
uses the same underlying RAM.
Since there are no page structures associated with the low physical
address region, some arbitrary kernel memory would be interpreted as a
page structure for the vDSO pages and badness ensues.
Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14229/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
This patch fixes the possibility of a deadlock when bringing up
secondary CPUs.
The deadlock occurs because the set_cpu_online() is called before
synchronise_count_slave(). This can cause a deadlock if the boot CPU,
having scheduled another thread, attempts to send an IPI to the
secondary CPU, which it sees has been marked online. The secondary is
blocked in synchronise_count_slave() waiting for the boot CPU to enter
synchronise_count_master(), but the boot cpu is blocked in
smp_call_function_many() waiting for the secondary to respond to it's
IPI request.
Fix this by marking the CPU online in cpu_callin_map and synchronising
counters before declaring the CPU online and calculating the maps for
IPIs.
In the mipsr2_decoder() function, used to emulate pre-MIPSr6
instructions that were removed in MIPSr6, the init_fpu() function is
called if a removed pre-MIPSr6 floating point instruction is the first
floating point instruction used by the task. However, init_fpu()
performs varous actions that rely upon not being migrated. For example
in the most basic case it sets the coprocessor 0 Status.CU1 bit to
enable the FPU & then loads FP register context into the FPU registers.
If the task were to migrate during this time, it may end up attempting
to load FP register context on a different CPU where it hasn't set the
CU1 bit, leading to errors such as:
If the i2c device is already runtime suspended, if qup_i2c_suspend is
executed during suspend-to-idle or suspend-to-ram it will result in the
following splat:
CPU: 3 PID: 1593 Comm: bash Tainted: G W 4.8.0-rc3 #14
Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
PC is at clk_core_unprepare+0x80/0x90
LR is at clk_unprepare+0x28/0x40
pc : [<ffff0000086eecf0>] lr : [<ffff0000086f0c58>] pstate: 60000145
Call trace:
clk_core_unprepare+0x80/0x90
qup_i2c_disable_clocks+0x2c/0x68
qup_i2c_suspend+0x10/0x20
platform_pm_suspend+0x24/0x68
...
This patch fixes the issue by executing qup_i2c_pm_suspend_runtime
conditionally in qup_i2c_suspend.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Reviewed-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
the eg20t driver call request_irq() function before the pch_base_address,
base address of i2c controller's register, is assigned an effective value.
there is one possible scenario that an interrupt which isn't inside eg20t
arrives immediately after request_irq() is executed when i2c controller
shares an interrupt number with others. since the interrupt handler
pch_i2c_handler() has already active as shared action, it will be called
and read its own register to determine if this interrupt is from itself.
At that moment, since base address of i2c registers is not remapped
in kernel space yet,so the INT handler will access an illegal address
and then a error occurs.
Signed-off-by: Yadi.hu <yadi.hu@windriver.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
If the subvol/snapshot create/destroy ioctls are passed a regular file
with execute permissions set, we'll eventually Oops while trying to do
inode->i_op->lookup via lookup_one_len.
This patch ensures that the file descriptor refers to a directory.
Due to an apparent copy/paste bug, the number of counters for the
beacon configuration were checked twice, instead of checking the
number of probe response counters. Fix this to check the number of
probe response counters before parsing those.
Fixes: 9a774c78e211 ("cfg80211: Support multiple CSA counters") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The reason for this suspend error is because when the CAN interface is not
active the clocks are disabled and then flexcan_chip_enable() will
always fail due to a timeout error.
In order to fix this issue, only call flexcan_chip_enable/disable()
when the CAN interface is active.
Based on a patch from Dong Aisheng in the NXP kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
init_tlb_ubc() looked unnecessary to me: tlb_ubc is statically
initialized with zeroes in the init_task, and copied from parent to
child while it is quiescent in arch_dup_task_struct(); so I went to
delete it.
But inserted temporary debug WARN_ONs in place of init_tlb_ubc() to
check that it was always empty at that point, and found them firing:
because memcg reclaim can recurse into global reclaim (when allocating
biosets for swapout in my case), and arrive back at the init_tlb_ubc()
in shrink_node_memcg().
Resetting tlb_ubc.flush_required at that point is wrong: if the upper
level needs a deferred TLB flush, but the lower level turns out not to,
we miss a TLB flush. But fortunately, that's the only part of the
protocol that does not nest: with the initialization removed, cpumask
collects bits from upper and lower levels, and flushes TLB when needed.
Fixes: 72b252aed506 ("mm: send one IPI per CPU to TLB flush all entries after unmapping pages") Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The iter->seq can be reset outside the protection of the mutex. So can
reading of user data. Move the mutex up to the beginning of the function.
Fixes: d7350c3f45694 ("tracing/core: make the read callbacks reentrants") Reported-by: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
There is a cut and paste issue here. The bug is that we are allocating
more memory than necessary for msp_maps. We should be allocating enough
space for a map_info struct (144 bytes) but we instead allocate enough
for an mtd_info struct (1840 bytes). It's a small waste.
The other part of this is not harmful but when we allocated msp_flash
then we allocated enough space fro a map_info pointer instead of an
mtd_info pointer. But since pointers are the same size it works out
fine.
Anyway, I decided to clean up all three allocations a bit to make them
a bit more consistent and clear.
Fixes: 68aa0fa87f6d ('[MTD] PMC MSP71xx flash/rootfs mappings') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Switching iov_iter fault-in to multipages variants has exposed an old
bug in underlying fault_in_multipages_...(); they break if the range
passed to them wraps around. Normally access_ok() done by callers will
prevent such (and it's a guaranteed EFAULT - ERR_PTR() values fall into
such a range and they should not point to any valid objects).
However, on architectures where userland and kernel live in different
MMU contexts (e.g. s390) access_ok() is a no-op and on those a range
with a wraparound can reach fault_in_multipages_...().
Since any wraparound means EFAULT there, the fix is trivial - turn
those
while (uaddr <= end)
...
into
if (unlikely(uaddr > end))
return -EFAULT;
do
...
while (uaddr <= end);
Reported-by: Jan Stancek <jstancek@redhat.com> Tested-by: Jan Stancek <jstancek@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
fanotify_get_response() calls fsnotify_remove_event() when it finds that
group is being released from fanotify_release() (bypass_perm is set).
However the event it removes need not be only in the group's notification
queue but it can have already moved to access_list (userspace read the
event before closing the fanotify instance fd) which is protected by a
different lock. Thus when fsnotify_remove_event() races with
fanotify_release() operating on access_list, the list can get corrupted.
Fix the problem by moving all the logic removing permission events from
the lists to one place - fanotify_release().
Fixes: 5838d4442bd5 ("fanotify: fix double free of pending permission events") Link: http://lkml.kernel.org/r/1473797711-14111-3-git-send-email-jack@suse.cz Signed-off-by: Jan Kara <jack@suse.cz> Reported-by: Miklos Szeredi <mszeredi@redhat.com> Tested-by: Miklos Szeredi <mszeredi@redhat.com> Reviewed-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
xfs_wait_buftarg() waits for all pending I/O, drains the ioend
completion workqueue and walks the LRU until all buffers in the cache
have been released. This is traditionally an unmount operation` but the
mechanism is also reused during filesystem freeze.
xfs_wait_buftarg() invokes drain_workqueue() as part of the quiesce,
which is intended more for a shutdown sequence in that it indicates to
the queue that new operations are not expected once the drain has begun.
New work jobs after this point result in a WARN_ON_ONCE() and are
otherwise dropped.
With filesystem freeze, however, read operations are allowed and can
proceed during or after the workqueue drain. If such a read occurs
during the drain sequence, the workqueue infrastructure complains about
the queued ioend completion work item and drops it on the floor. As a
result, the buffer remains on the LRU and the freeze never completes.
Despite the fact that the overall buffer cache cleanup is not necessary
during freeze, fix up this operation such that it is safe to invoke
during non-unmount quiesce operations. Replace the drain_workqueue()
call with flush_workqueue(), which runs a similar serialization on
pending workqueue jobs without causing new jobs to be dropped. This is
safe for unmount as unmount independently locks out new operations by
the time xfs_wait_buftarg() is invoked.
cc: <stable@vger.kernel.org> Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Somewhere along the way the autofs expire operation has changed to hold
a spin lock over expired dentry selection. The autofs indirect mount
expired dentry selection is complicated and quite lengthy so it isn't
appropriate to hold a spin lock over the operation.
Commit 47be61845c77 ("fs/dcache.c: avoid soft-lockup in dput()") added a
might_sleep() to dput() causing a WARN_ONCE() about this usage to be
issued.
But the spin lock doesn't need to be held over this check, the autofs
dentry info. flags are enough to block walks into dentrys during the
expire.
I've left the direct mount expire as it is (for now) because it is much
simpler and quicker than the indirect mount expire and adding spin lock
release and re-aquires would do nothing more than add overhead.
Fixes: 47be61845c77 ("fs/dcache.c: avoid soft-lockup in dput()") Link: http://lkml.kernel.org/r/20160912014017.1773.73060.stgit@pluto.themaw.net Signed-off-by: Ian Kent <raven@themaw.net> Reported-by: Takashi Iwai <tiwai@suse.de> Tested-by: Takashi Iwai <tiwai@suse.de> Cc: Takashi Iwai <tiwai@suse.de> Cc: NeilBrown <neilb@suse.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
* make autofs4_expire_indirect() skip the dentries being in process of
expiry
* do *not* mess with list_move(); making sure that dentry with
AUTOFS_INF_EXPIRING are not picked for expiry is enough.
* do not remove NO_RCU when we set EXPIRING, don't bother with smp_mb()
there. Clear it at the same time we clear EXPIRING. Makes a bunch of
tests simpler.
* rename NO_RCU to WANT_EXPIRE, which is what it really is.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Cc: Ian Kent <raven@themaw.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
commit bc8c20acaea1 ("bridge: multicast: treat igmpv3 report with
INCLUDE and no sources as a leave") seems to have accidentally reverted
commit 47cc84ce0c2f ("bridge: fix parsing of MLDv2 reports"). This
commit brings back a change to br_ip6_multicast_mld2_report() where
parsing of MLDv2 reports stops when the first group is successfully
added to the MDB cache.
Fixes: bc8c20acaea1 ("bridge: multicast: treat igmpv3 report with INCLUDE and no sources as a leave") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Commit b70661c70830 ("net: smc91x: use run-time configuration on all ARM
machines") broke some ARM platforms through several mistakes. Firstly,
the access size must correspond to the following rule:
(a) at least one of 16-bit or 8-bit access size must be supported
(b) 32-bit accesses are optional, and may be enabled in addition to
the above.
Secondly, it provides no emulation of 16-bit accesses, instead blindly
making 16-bit accesses even when the platform specifies that only 8-bit
is supported.
Reorganise smc91x.h so we can make use of the existing 16-bit access
emulation already provided - if 16-bit accesses are supported, use
16-bit accesses directly, otherwise if 8-bit accesses are supported,
use the provided 16-bit access emulation. If neither, BUG(). This
exactly reflects the driver behaviour prior to the commit being fixed.
Since the conversion incorrectly cut down the available access sizes on
several platforms, we also need to go through every platform and fix up
the overly-restrictive access size: Arnd assumed that if a platform can
perform 32-bit, 16-bit and 8-bit accesses, then only a 32-bit access
size needed to be specified - not so, all available access sizes must
be specified.
This likely fixes some performance regressions in doing this: if a
platform does not support 8-bit accesses, 8-bit accesses have been
emulated by performing a 16-bit read-modify-write access.
Tested on the Intel Assabet/Neponset platform, which supports only 8-bit
accesses, which was broken by the original commit.
Fixes: b70661c70830 ("net: smc91x: use run-time configuration on all ARM machines") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
This reverts:
commit 33c133cc7598 ("phy: IRQ cannot be shared")
On hardware with multiple PHY devices hooked up to the same IRQ line, allow
them to share it.
Sergei Shtylyov says:
"I'm not sure now what was the reason I concluded that the IRQ sharing
was impossible... most probably I thought that the kernel IRQ handling
code exited the loop over the IRQ actions once IRQ_HANDLED was returned
-- which is obviously not so in reality..."
Signed-off-by: Xander Huff <xander.huff@ni.com> Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
We kept shadow copies of which interrupt sources we have enabled and
disabled, but due to an order bug in how intrl2_mask_clear was defined,
we could run into the following scenario:
CPU0 CPU1
intrl2_1_mask_clear(..)
sets INTRL2_CPU_MASK_CLEAR
bcm_sf2_switch_1_isr
read INTRL2_CPU_STATUS and masks with stale
irq1_mask value
updates irq1_mask value
Which would make us loop again and again trying to process and interrupt
we are not clearing since our copy of whether it was enabled before
still indicates it was not. Fix this by updating the shadow copy first,
and then unasking at the HW level.
Fixes: 246d7f773c13 ("net: dsa: add Broadcom SF2 switch driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Set and verify signature calculates the signature for each of the
mailbox nodes, even for those that are unused (from cache). Added
a missing length check to set and verify only those which are used.
While here, also moved the setting of msg's nodes token to where we
already go over them. This saves a pass because checksum is disabled,
and the only useful thing remaining that set signature does is setting
the token.
Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB
adapters') Signed-off-by: Paul Blakey <paulb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
I feel like we should maybe return -ENOMEM or -ENOBUFS, but I'm not sure
userspace is equipped to handle that. Anyway, this is better than a GPF
and looks somewhat consistent with other tipc_msg_create() callers.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
If iriap_register_lsap() fails to allocate memory, self->lsap is
set to NULL. However, none of the callers handle the failure and
irlmp_connect_request() will happily dereference it:
There's more problems with missing error checks in iriap_init() (and
indeed all of irda_init()), but that's a bigger problem that needs
very careful review and testing. This patch will fix the most serious
bug (as it's easily reached from unprivileged userspace).
I have tested my patch with a reproducer.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
When executing the script included below, the netns delete operation
hangs with the following message (repeated at 10 second intervals):
kernel:unregister_netdevice: waiting for lo to become free. Usage count = 1
This occurs because a reference to the lo interface in the "secure" netns
is still held by a dst entry in the xfrm bundle cache in the init netns.
Address this problem by garbage collecting the tunnel netns flow cache
when a cross-namespace vti interface receives a NETDEV_DOWN notification.
A more detailed description of the problem scenario (referencing commands
in the script below):
(1) ip link add vti_test type vti local 1.1.1.1 remote 1.1.1.2 key 1
The vti_test interface is created in the init namespace. vti_tunnel_init()
attaches a struct ip_tunnel to the vti interface's netdev_priv(dev),
setting the tunnel net to &init_net.
(2) ip link set vti_test netns secure
The vti_test interface is moved to the "secure" netns. Note that
the associated struct ip_tunnel still has tunnel->net set to &init_net.
Note that tunnel->net is the init namespace, while skb_dst(skb) references
the vti_test interface in the "secure" namespace. The returned dst
references an interface in the init namespace.
Also note that the first parameter to xfrm_lookup() determines which flow
cache is used to store the computed xfrm bundle, so after xfrm_lookup()
returns there will be a cached bundle in the init namespace flow cache
with a dst referencing a device in the "secure" namespace.
(4) ip netns del secure
Kernel begins to delete the "secure" namespace. At some point the
vti_test interface is deleted, at which point dst_ifdown() changes
the dst->dev in the cached xfrm bundle flow from vti_test to lo (still
in the "secure" namespace however).
Since nothing has happened to cause the init namespace's flow cache
to be garbage collected, this dst remains attached to the flow cache,
so the kernel loops waiting for the last reference to lo to go away.
<Begin script>
ip link add br1 type bridge
ip link set dev br1 up
ip addr add dev br1 1.1.1.1/8
ip netns add secure
ip link add vti_test type vti local 1.1.1.1 remote 1.1.1.2 key 1
ip link set vti_test netns secure
ip netns exec secure ip link set vti_test up
ip netns exec secure ip link s lo up
ip netns exec secure ip addr add dev lo 192.168.100.1/24
ip netns exec secure ip route add 192.168.200.0/24 dev vti_test
ip xfrm policy flush
ip xfrm state flush
ip xfrm policy add dir out tmpl src 1.1.1.1 dst 1.1.1.2 \
proto esp mode tunnel mark 1
ip xfrm policy add dir in tmpl src 1.1.1.2 dst 1.1.1.1 \
proto esp mode tunnel mark 1
ip xfrm state add src 1.1.1.1 dst 1.1.1.2 proto esp spi 1 \
mode tunnel enc des3_ede 0x112233445566778811223344556677881122334455667788
ip xfrm state add src 1.1.1.2 dst 1.1.1.1 proto esp spi 1 \
mode tunnel enc des3_ede 0x112233445566778811223344556677881122334455667788
Reported-by: Hangbin Liu <haliu@redhat.com> Reported-by: Jan Tluka <jtluka@redhat.com> Signed-off-by: Lance Richardson <lrichard@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Right now we use the 'readlock' both for protecting some of the af_unix
IO path and for making the bind be single-threaded.
The two are independent, but using the same lock makes for a nasty
deadlock due to ordering with regards to filesystem locking. The bind
locking would want to nest outside the VSF pathname locking, but the IO
locking wants to nest inside some of those same locks.
We tried to fix this earlier with commit c845acb324aa ("af_unix: Fix
splice-bind deadlock") which moved the readlock inside the vfs locks,
but that caused problems with overlayfs that will then call back into
filesystem routines that take the lock in the wrong order anyway.
Splitting the locks means that we can go back to having the bind lock be
the outermost lock, and we don't have any deadlocks with lock ordering.
Acked-by: Rainer Weikusat <rweikusat@cyberadapt.com> Acked-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
It turns out that it just replaces one deadlock with another one: we can
still get the wrong lock ordering with the readlock due to overlayfs
calling back into the filesystem layer and still taking the vfs locks
after the readlock.
The proper solution ends up being to just split the readlock into two
pieces: the bind lock (taken *outside* the vfs locks) and the IO lock
(taken *inside* the filesystem locks). The two locks are independent
anyway.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
(a) Create bonding master
> modprobe bonding miimon=50
(b) Create macvlan bridge on eth2
> ip link add link eth2 dev mvl0 address aa:0:0:0:0:01 \
type macvlan
(c) Now try adding eth2 into the bond
> echo +eth2 > /sys/class/net/bond0/bonding/slaves
<crash>
Bonding does lots of things before checking if the device enslaved is
busy or not.
In this case when the notifier call-chain sends notifications, the
bond_netdev_event() assumes that the rx_handler /rx_handler_data is
registered while the bond_enslave() hasn't progressed far enough to
register rx_handler for the new slave.
This patch adds a rx_handler check that can be performed right at the
beginning of the enslave code to avoid getting into this situation.
Signed-off-by: Mahesh Bandewar <maheshb@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
gcc-6 warns about code in the nouveau driver that is obviously silly:
drivers/gpu/drm/nouveau/nvkm/engine/pm/nv40.c: In function 'nv40_perfctr_next':
drivers/gpu/drm/nouveau/nvkm/engine/pm/nv40.c:62:19: warning: self-comparison always evaluats to false [-Wtautological-compare]
if (pm->sequence != pm->sequence) {
The behavior was accidentally introduced in a patch described as "This is
purely preparation for upcoming commits, there should be no code changes here.".
As far as I can tell, that was true for the rest of that patch except for
this one function, which has been changed to a NOP.
This patch restores the original behavior.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 8c1aeaa13954 ("drm/nouveau/pm: cosmetic changes") Reviewed-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Fix indent warning when building with gcc 6:
drivers/staging/iio/adc/ad7192.c:239:4: warning: statement is indented
as if it were guarded by... [-Wmisleading-indentation]
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
A cleanup patch in linux-3.18 moved around some code in the ath9k
driver and left some code to be indented in a misleading way,
made worse by the addition of some new code for p2p mode, as
discovered by a new gcc-6 warning:
drivers/net/wireless/ath/ath9k/init.c: In function 'ath9k_set_hw_capab':
drivers/net/wireless/ath/ath9k/init.c:851:4: warning: statement is indented as if it were guarded by... [-Wmisleading-indentation]
hw->wiphy->iface_combinations = if_comb;
^~
drivers/net/wireless/ath/ath9k/init.c:847:3: note: ...this 'if' clause, but it is not
if (ath9k_is_chanctx_enabled())
^~
The code is in fact correct, but the indentation is not, so I'm
reformatting it as it should have been after the original cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 499afaccf6f3 ("ath9k: Isolate ath9k_use_chanctx module parameter") Fixes: eb61f9f623f7 ("ath9k: advertise p2p dev support when chanctx") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
gcc-6 points out an obviously silly comparison in vpfe_get_app_input_index():
drivers/media/platform/am437x/am437x-vpfe.c: In function 'vpfe_get_app_input_index':
drivers/media/platform/am437x/am437x-vpfe.c:1709:27: warning: self-comparison always evaluats to true [-Wtautological-compare]
client->adapter->nr == client->adapter->nr) {
^~
This was introduced in a slighly incorrect conversion, and it's
clear that the comparison was meant to compare the iterator
to the current subdev instead, as we do in the line above.
Fixes: d37232390fd4 ("[media] media: am437x-vpfe: match the OF node/i2c addr instead of name") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Some of our "for_each_xyz()" macro constructs make gcc unhappy about
lack of braces around if-statements inside or outside the loop, because
the loop construct itself has a "if-then-else" statement inside of it.
The resulting warnings look something like this:
drivers/gpu/drm/i915/i915_debugfs.c: In function ‘i915_dump_lrc’:
drivers/gpu/drm/i915/i915_debugfs.c:2103:6: warning: suggest explicit braces to avoid ambiguous ‘else’ [-Wparentheses]
if (ctx != dev_priv->kernel_context)
^
even if the code itself is fine.
Since the warning is fairly easy to avoid by adding a braces around the
if-statement near the for_each_xyz() construct, do so, rather than
disabling the otherwise potentially useful warning.
(The if-then-else statements used in the "for_each_xyz()" constructs are
designed to be inherently safe even with no braces, but in this case
it's quite understandable that gcc isn't really able to tell that).
This finally leaves the standard "allmodconfig" build with just a
handful of remaining warnings, so new and valid warnings hopefully will
stand out.
gcc points out code that is not indented the way it is
interpreted:
net/caif/cfpkt_skbuff.c: In function 'cfpkt_setlen':
net/caif/cfpkt_skbuff.c:289:4: error: statement is indented as if it were guarded by... [-Werror=misleading-indentation]
return cfpkt_getlen(pkt);
^~~~~~
net/caif/cfpkt_skbuff.c:286:3: note: ...this 'else' clause, but it is not
else
^~~~
It is clear from the context that not returning here would be
a bug, as we'd end up passing a negative length into a function
that takes a u16 length, so it is not missing curly braces
here, and I'm assuming that the indentation is the only part
that's wrong about it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
With the latest gcc compilers, they give a warning if
__builtin_return_address() parameter is greater than 0. That is because if
it is used by a function called by a top level function (or in the case of
the kernel, by assembly), it can try to access stack frames outside the
stack and crash the system.
The tracing system uses __builtin_return_address() of up to 2! But it is
well aware of the dangers that it may have, and has even added precautions
to protect against it (see the thunk code in arch/x86/entry/thunk*.S)
Linus originally added KBUILD_CFLAGS that would suppress the warning for the
entire kernel, as simply adding KBUILD_CFLAGS to the tracing directory
wouldn't work. The tracing directory plays a bit with the CFLAGS and
requires a little more logic.
This adds that special logic to only suppress the warning for the tracing
directory. If it is used anywhere else outside of tracing, the warning will
still be triggered.
Link: http://lkml.kernel.org/r/20160728223043.51996267@grimm.local.home Tested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Newer versions of gcc warn about the use of __builtin_return_address()
with a non-zero argument when "-Wall" is specified:
kernel/trace/trace_irqsoff.c: In function ‘stop_critical_timings’:
kernel/trace/trace_irqsoff.c:433:86: warning: calling ‘__builtin_return_address’ with a nonzero argument is unsafe [-Wframe-address]
stop_critical_timing(CALLER_ADDR0, CALLER_ADDR1);
[ .. repeats a few times for other similar cases .. ]
It is true that a non-zero argument is somewhat dangerous, and we do not
actually have very many uses of that in the kernel - but the ftrace code
does use it, and as Stephen Rostedt says:
"We are well aware of the danger of using __builtin_return_address() of
> 0. In fact that's part of the reason for having the "thunk" code in
x86 (See arch/x86/entry/thunk_{64,32}.S). [..] it adds extra frames
when tracking irqs off sections, to prevent __builtin_return_address()
from accessing bad areas. In fact the thunk_32.S states: 'Trampoline to
trace irqs off. (otherwise CALLER_ADDR1 might crash)'."
For now, __builtin_return_address() with a non-zero argument is the best
we can do, and the warning is not helpful and can end up making people
miss other warnings for real problems.
So disable the frame-address warning on compilers that need it.
Acked-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Several build configurations had already disabled this warning because
it generates a lot of false positives. But some had not, and it was
still enabled for "allmodconfig" builds, for example.
Looking at the warnings produced, every single one I looked at was a
false positive, and the warnings are frequent enough (and big enough)
that they can easily hide real problems that you don't notice in the
noise generated by -Wmaybe-uninitialized.
The warning is good in theory, but this is a classic case of a warning
that causes more problems than the warning can solve.
If gcc gets better at avoiding false positives, we may be able to
re-enable this warning. But as is, we're better off without it, and I
want to be able to see the *real* warnings.
When gcov profiling is enabled, we see a lot of spurious warnings about
possibly uninitialized variables being used:
arch/arm/mm/dma-mapping.c: In function 'arm_coherent_iommu_map_page':
arch/arm/mm/dma-mapping.c:1085:16: warning: 'start' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/clk/st/clk-flexgen.c: In function 'st_of_flexgen_setup':
drivers/clk/st/clk-flexgen.c:323:9: warning: 'num_parents' may be used uninitialized in this function [-Wmaybe-uninitialized]
kernel/cgroup.c: In function 'cgroup_mount':
kernel/cgroup.c:2119:11: warning: 'root' may be used uninitialized in this function [-Wmaybe-uninitialized]
All of these are false positives, so it seems better to just disable
the warnings whenever GCOV is enabled. Most users don't enable GCOV,
and based on a prior patch, it is now also disabled for 'allmodconfig'
builds, so there should be no downsides of doing this.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
CONFIG_PROFILE_ALL_BRANCHES confuses gcc-5.x to the degree that it prints
incorrect warnings about a lot of variables that it thinks can be used
uninitialized, e.g.:
i2c/busses/i2c-diolan-u2c.c: In function 'diolan_usb_xfer':
i2c/busses/i2c-diolan-u2c.c:391:16: warning: 'byte' may be used uninitialized in this function
iio/gyro/itg3200_core.c: In function 'itg3200_probe':
iio/gyro/itg3200_core.c:213:6: warning: 'val' may be used uninitialized in this function
leds/leds-lp55xx-common.c: In function 'lp55xx_update_bits':
leds/leds-lp55xx-common.c:350:6: warning: 'tmp' may be used uninitialized in this function
misc/bmp085.c: In function 'show_pressure':
misc/bmp085.c:363:10: warning: 'pressure' may be used uninitialized in this function
power/ds2782_battery.c: In function 'ds2786_get_capacity':
power/ds2782_battery.c:214:17: warning: 'raw' may be used uninitialized in this function
These are all false positives that either rob someone's time when trying
to figure out whether they are real, or they get people to send wrong
patches to shut up the warnings.
Nobody normally wants to run a CONFIG_PROFILE_ALL_BRANCHES kernel in
production, so disabling the whole class of warnings for this configuration
has no serious downsides either.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Steven Rostedt <rostedtgoodmis.org> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
When the kernel path contains a space or a colon somewhere in the path
name, the modules_install target doesn't work anymore, as the path names
are not enclosed in double quotes. It is also supposed that and O= build
will suffer from the same weakness as modules_install.
Instead of checking and improving kbuild to resist to directories
including these characters, error out early to prevent any build if the
kernel's main directory contains a space.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Running "make O=foo" (with a relative directory path) fails with:
scripts/Makefile.include:3: *** O=foo does not exist. Stop.
/home/jpoimboe/git/linux/Makefile:1547: recipe for target 'tools/objtool' failed
The tools Makefile gets confused by the relative path and tries to build
objtool in tools/foo. Convert the output directory to an absolute path
before passing it to the tools Makefile.
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-next@vger.kernel.org Cc: linux@roeck-us.net Cc: live-patching@vger.kernel.org Link: http://lkml.kernel.org/r/94a078c6c998fac9f01a14f574008bf7dff40191.1457016803.git.jpoimboe@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Commit 627189797807 ("Makefile: Document ability to make file.lst
and file.S") document ability to make file.S, but there isn't such
ability in kbuild, so revert it.
Signed-off-by: Wang YanQing <udknight@gmail.com> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Based on a x86-only patch by Andy Lutomirski <luto@amacapital.net>
With modular kernels, 'make install' is going to need the installed
modules at some point to generate the initramfs.
Signed-off-by: Michal Marek <mmarek@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
If we punch a hole on a reflink such that following conditions are met:
1. start offset is on a cluster boundary
2. end offset is not on a cluster boundary
3. (end offset is somewhere in another extent) or
(hole range > MAX_CONTIG_BYTES(1MB)),
we dont COW the first cluster starting at the start offset. But in this
case, we were wrongly passing this cluster to
ocfs2_zero_range_for_truncate() to zero out. This will modify the
cluster in place and zero it in the source too.
Fix this by skipping this cluster in such a scenario.
To reproduce:
1. Create a random file of say 10 MB
xfs_io -c 'pwrite -b 4k 0 10M' -f 10MBfile
2. Reflink it
reflink -f 10MBfile reflnktest
3. Punch a hole at starting at cluster boundary with range greater that
1MB. You can also use a range that will put the end offset in another
extent.
fallocate -p -o 0 -l 1048615 reflnktest
4. sync
5. Check the first cluster in the source file. (It will be zeroed out).
dd if=10MBfile iflag=direct bs=<cluster size> count=1 | hexdump -C
Link: http://lkml.kernel.org/r/1470957147-14185-1-git-send-email-ashish.samant@oracle.com Signed-off-by: Ashish Samant <ashish.samant@oracle.com> Reported-by: Saar Maoz <saar.maoz@oracle.com> Reviewed-by: Srinivas Eeda <srinivas.eeda@oracle.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <joseph.qi@huawei.com> Cc: Eric Ren <zren@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Commit ac7cf246dfdb ("ocfs2/dlm: fix race between convert and recovery")
checks if lockres master has changed to identify whether new master has
finished recovery or not. This will introduce a race that right after
old master does umount ( means master will change), a new convert
request comes.
In this case, it will reset lockres state to DLM_RECOVERING and then
retry convert, and then fail with lockres->l_action being set to
OCFS2_AST_INVALID, which will cause inconsistent lock level between
ocfs2 and dlm, and then finally BUG.
Since dlm recovery will clear lock->convert_pending in
dlm_move_lockres_to_recovery_list, we can use it to correctly identify
the race case between convert and recovery. So fix it.
Fixes: ac7cf246dfdb ("ocfs2/dlm: fix race between convert and recovery") Link: http://lkml.kernel.org/r/57CE1569.8010704@huawei.com Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Signed-off-by: Jun Piao <piaojun@huawei.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The current implementation uses a global per-cpu array to store
data which are used to derive the next IV. This is insecure as
the attacker may change the stored data.
This patch removes all traces of chaining and replaces it with
multiplication of the salt and the sequence number.
When we need to allocate a temporary blkcipher_walk_next and it
fails, the code is supposed to take the slow path of processing
the data block by block. However, due to an unrelated change
we instead end up dereferencing the NULL pointer.
This patch fixes it by moving the unrelated bsize setting out
of the way so that we enter the slow path as inteded.
The AES-CTR glue code avoids calling into the blkcipher API for the
tail portion of the walk, by comparing the remainder of walk.nbytes
modulo AES_BLOCK_SIZE with the residual nbytes, and jumping straight
into the tail processing block if they are equal. This tail processing
block checks whether nbytes != 0, and does nothing otherwise.
However, in case of an allocation failure in the blkcipher layer, we
may enter this code with walk.nbytes == 0, while nbytes > 0. In this
case, we should not dereference the source and destination pointers,
since they may be NULL. So instead of checking for nbytes != 0, check
for (walk.nbytes % AES_BLOCK_SIZE) != 0, which implies the former in
non-error conditions.
Fixes: 86464859cc77 ("crypto: arm - AES in ECB/CBC/CTR/XTS modes using ARMv8 Crypto Extensions") Reported-by: xiakaixu <xiakaixu@huawei.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The AES-CTR glue code avoids calling into the blkcipher API for the
tail portion of the walk, by comparing the remainder of walk.nbytes
modulo AES_BLOCK_SIZE with the residual nbytes, and jumping straight
into the tail processing block if they are equal. This tail processing
block checks whether nbytes != 0, and does nothing otherwise.
However, in case of an allocation failure in the blkcipher layer, we
may enter this code with walk.nbytes == 0, while nbytes > 0. In this
case, we should not dereference the source and destination pointers,
since they may be NULL. So instead of checking for nbytes != 0, check
for (walk.nbytes % AES_BLOCK_SIZE) != 0, which implies the former in
non-error conditions.
Fixes: 49788fe2a128 ("arm64/crypto: AES-ECB/CBC/CTR/XTS using ARMv8 NEON and Crypto Extensions") Reported-by: xiakaixu <xiakaixu@huawei.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Commit 76174004a0f19785a328f40388e87e982bbf69b9
(tcp: do not slow start when cwnd equals ssthresh )
introduced regression in TCP YeAH. Using 100ms delay 1% loss virtual
ethernet link kernel 4.2 shows bandwidth ~500KB/s for single TCP
connection and kernel 4.3 and above (including 4.8-rc4) shows bandwidth
~100KB/s.
That is caused by stalled cwnd when cwnd equals ssthresh. This patch
fixes it by proper increasing cwnd in this case.
Signed-off-by: Artem Germanov <agermanov@anchorfree.com> Acked-by: Dmitry Adamushko <d.adamushko@anchorfree.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by: Holger Hoffstätte <holger@applied-asynchrony.com> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Neither the failure or success paths of ping_v6_sendmsg release
the dst it acquires. This leads to a flood of warnings from
"net/core/dst.c:288 dst_release" on older kernels that
don't have 8bf4ada2e21378816b28205427ee6b0e1ca4c5f1 backported.
That patch optimistically hoped this had been fixed post 3.10, but
it seems at least one case wasn't, where I've seen this triggered
a lot from machines doing unprivileged icmp sockets.
Cc: Martin Lau <kafai@fb.com> Signed-off-by: Dave Jones <davej@codemonkey.org.uk> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Dave Forster <dforster@brocade.com> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
new_insert_key only makes any sense when it's associated with a
new_insert_ptr, which is initialized to NULL and changed to a
buffer_head when we also initialize new_insert_key. We can key off of
that to avoid the uninitialized warning.
Link: http://lkml.kernel.org/r/5eca5ffb-2155-8df2-b4a2-f162f105efed@suse.com Signed-off-by: Jeff Mahoney <jeffm@suse.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Jan Kara <jack@suse.cz> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1629386
> 2 ../kernel/cpuset.c:2101:11: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
> 1 ../kernel/cpuset.c:2101:2: warning: initialization from incompatible pointer type
> 1 ../kernel/cpuset.c:2101:2: warning: (near initialization for 'cpuset_cgrp_subsys.fork')
This got introduced by 06ec7a1d7646 ("cpuset: make sure new tasks
conform to the current config of the cpuset"). In the upstream
kernel, the function prototype was changed as of b53202e63089
("cgroup: kill cgrp_ss_priv[CGROUP_CANFORK_COUNT] and friends").
That patch is not suitable for stable kernels, and fortunately
the warning seems harmless as the prototypes only differ in the
second argument that is unused. Adding that argument gets rid
of the warning:
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Rewrite abs() so that its return type does not depend on the
architecture and no unexpected type conversion happen inside of it. The
only conversion is from unsigned to signed type. char is left as a
return type but treated as a signed type regradless of it's actual
signedness.
With the old version, int arguments were promoted to long and depending
on architecture a long argument might result in s64 or long return type
(which may or may not be the same).
This came after some back and forth with Nicolas. The current macro has
different return type (for the same input type) depending on
architecture which might be midly iritating.
An alternative version would promote to int like so:
I have no preference but imagine Linus might. :] Nicolas argument against
is that promoting to int causes iconsistent behaviour:
int main(void) {
unsigned short a = 0, b = 1, c = a - b;
unsigned short d = abs(a - b);
unsigned short e = abs(c);
printf("%u %u\n", d, e); // prints: 1 65535
}
Then again, no sane person expects consistent behaviour from C integer
arithmetic. ;)
Note:
__builtin_types_compatible_p(unsigned char, char) is always false, and
__builtin_types_compatible_p(signed char, char) is also always false.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Reviewed-by: Nicolas Pitre <nico@linaro.org> Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Since commit acb2505d0119 ("openrisc: fix copy_from_user()"),
copy_from_user() returns the number of bytes requested, not the
number of bytes not copied.
arch/avr32/kernel/built-in.o: In function `arch_ptrace':
(.text+0x650): undefined reference to `___copy_from_user'
arch/avr32/kernel/built-in.o:(___ksymtab+___copy_from_user+0x0): undefined
reference to `___copy_from_user'
kernel/built-in.o: In function `proc_doulongvec_ms_jiffies_minmax':
(.text+0x5dd8): undefined reference to `___copy_from_user'
kernel/built-in.o: In function `proc_dointvec_minmax_sysadmin':
sysctl.c:(.text+0x6174): undefined reference to `___copy_from_user'
kernel/built-in.o: In function `ptrace_has_cap':
ptrace.c:(.text+0x69c0): undefined reference to `___copy_from_user'
kernel/built-in.o:ptrace.c:(.text+0x6b90): more undefined references to
`___copy_from_user' follow
Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
... that should zero on faults. Also remove the <censored> helpful
logics wrt range truncation copied from ppc32. Where it had ever
been needed only in case of copy_from_user() *and* had not been merged
into the mainline until a month after the need had disappeared.
A decade before openrisc went into mainline, I might add...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
... in all cases, including the failing access_ok()
Note that some architectures using asm-generic/uaccess.h have
__copy_from_user() not zeroing the tail on failure halfway
through. This variant works either way.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
It's -EFAULT, not -1 (and contrary to the comment in there,
__strnlen_user() can return 0 - on faults).
Acked-by: Richard Kuo <rkuo@codeaurora.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>