James Schulman [Thu, 7 Feb 2019 18:12:19 +0000 (12:12 -0600)]
ASoC: cs35l36: Add device tree documentation for CS35L36
Add device tree documentation for Cirrus Logic CS35L36
speaker amplifier
Signed-off-by: James Schulman <james.schulman@cirrus.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Acked-by: Brian Austin <brian.austin@cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
James Schulman [Thu, 7 Feb 2019 18:12:15 +0000 (12:12 -0600)]
ASoC: cs35l36: Add support for Cirrus CS35L36 Amplifier
Add driver support for Cirrus Logic CS35L36 boosted
speaker amplifier
Signed-off-by: James Schulman <james.schulman@cirrus.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Acked-by: Brian Austin <brian.austin@cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Paul Cercueil [Thu, 7 Feb 2019 13:31:42 +0000 (10:31 -0300)]
ASoC: codecs: Kconfig: Show knob, and depend on MIPS || COMPILE_TEST
Show the knob to enable or disable the jz4740-codec driver, add a
proper description, and add a dependency on MIPS || COMPILE_TEST, as
this driver is only useful on MIPS.
Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: sun4i-codec: Add Line Playback Volume, Line Boost Volume, Line Right, Line Left, Line Playback Switch
Add Line Playback Volume for Allwinner A10 and Allwinner A20.
Add Line Boost Volume for Allwinner A10 and Allwinner A20.
Add Line Right, Line Left, Line Playback Switch for Allwinner A10 and
Allwinner A20.
Signed-off-by: Danny Milosavljevic <dannym@scratchpost.org> Reviewed-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Mark Brown <broonie@kernel.org>
Add Mic1 Boost Volume and Mic2 Boost Volume for Allwinner A10 and for
Allwinner A20.
Those controls are in different registers per chip model, so put the
Allwinner A10 controls and the Allwinner A20 controls into the newly
split sun4i_codec_controls and sun7i_codec_controls, respectively.
Signed-off-by: Danny Milosavljevic <dannym@scratchpost.org> Reviewed-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Mark Brown <broonie@kernel.org>
a) build-time warnings when the table size isn't aligned with the enum
list
b) run-time warnings when the values are not initialized. This
requires an increase by one of all values to avoid the default 0.
Suggested-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: dapm: fix out-of-bounds accesses to DAPM lookup tables
KASAN reports and additional traces point to out-of-bounds accesses to
the dapm_up_seq and dapm_down_seq lookup tables. The indices used are
larger than the array definition.
Fix by adding missing entries for the new widget types in these two
lookup tables, and align them with PGA values.
Also the sequences for the following widgets were not defined. Since
their values defaulted to zero, assign them explicitly
Fixes: 8a70b4544ef4 ('ASoC: dapm: Add new widget type for constructing DAPM graphs on DSPs.'). Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Charles Keepax [Tue, 5 Feb 2019 11:18:13 +0000 (11:18 +0000)]
ASoC: compress: Add helper functions for component trigger/set_params
The trigger and set_params callbacks are called from 3 and 2 separate
loops respectively, tidy up the code a little by factoring these out
into helper functions.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Charles Keepax [Tue, 5 Feb 2019 11:18:12 +0000 (11:18 +0000)]
ASoC: compress: Clarify the intent of current compressed ops handling
For callbacks configuring the state of the components (trigger,
set_params, ack and set_metadata) simplify the code a little and make
intention clearer by aborting as soon as an error is encountered. The
operation has already failed and there is nothing to be gained from
processing the callbacks on additional components. The operations
currently abort after the callbacks, so this simply shortens the
error path.
For callbacks returning information from the driver (copy,
get_metadata, pointer, get_codec_caps, get_caps and get_params)
only look for the first callback provided, currently the code will
call every callback only returning the information provided by the
last. Since we can only return one set of data, it makes no sense to
request the data from every component. Again this just makes the
currently supported feature set a little more clear.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Philipp Zabel [Wed, 6 Feb 2019 15:29:47 +0000 (16:29 +0100)]
ASoC: ssm2602: Fix ADC powerup sequencing
According to the ssm2603 data sheet (control register sequencing), the
digital core should be activated only after all necessary bits in the
power register are enabled, and a delay determined by the decoupling
capacitor on the VMID pin has passed. If the digital core is activated
too early, or even before the ADC is powered up, audible artifacts
appear at the beginning of the recorded signal.
The digital core is also needed for playback, so when recording starts
it may already be enabled. This means we cannot get the power sequence
correct when we want to be able to start recording after playback.
As a workaround put the MIC mute switch into the DAPM routes. This
way we can keep the recording disabled until the MIC Bias has settled
and thus get rid of audible artifacts.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
m.felsch@pengutronix.de: adapt commit message
m.felsch@pengutronix.de: drop of configuration as mentioned by Mark:
https://patchwork.kernel.org/patch/10407449/ Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Mark Brown <broonie@kernel.org>
Charles Keepax [Wed, 6 Feb 2019 11:13:59 +0000 (11:13 +0000)]
ASoC: dapm: Check for NULL widget in dapm_update_dai_unlocked
DAIs linked to the dummy will not have an associated playback/capture
widget, so we need to skip the update in that case.
Fixes: 078a85f2806f ("ASoC: dapm: Only power up active channels from a DAI") Reported-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Tested-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org>
Bard liao [Fri, 1 Feb 2019 17:07:40 +0000 (11:07 -0600)]
ASoC: topology: unload physical dai link in remove
soc_tplg_link_config() will find the physical dai link and call
soc_tplg_dai_link_load() to load the BE dai link. Currently remove_link()
is only used to remove the FE dai link which is created by the topology.
The BE dai link cannot however be unloaded in snd_soc_tplg_component
_remove(), which is problematic if anything needs to be released or
reinitialized.
This patch aligns the definitions of dynamic types with the existing
UAPI and adds a new remove_backend_link() routine to unload the the BE
dai link when snd_soc_tplg_component_remove() is invoked.
Signed-off-by: Bard liao <yung-chuan.liao@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Curtis Malainey [Tue, 29 Jan 2019 21:47:09 +0000 (13:47 -0800)]
ASoC: soc-core: clear platform pointers on error
Originally snd_soc_init_platform was not cleaning up its pointers, this
was fixed to always reallocate dynamic memory but created a memory leak
when snd_soc_init_platform was called multiple times during the same
probe attempt and also threw away any changes made to the struct between
calls. In order to avoid reallocating memory that is still valid, the
behaviour will be changed to clear the dynamically set pointers on a
probe error and a unregister event and snd_soc_init_platform will go
back to its original behaviour of only allocating null pointers so it will
stop throwing away valid changes.
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org> Signed-off-by: Mark Brown <broonie@kernel.org>
Zhiwei Jiang [Thu, 31 Jan 2019 11:30:05 +0000 (19:30 +0800)]
ASoC: dapm: Add warnings for widget overwrite when adding route
Currently, in some complex cases, more than one widgets have same
name and registed from differnt dapm context, and route add from
another context too. When snd_soc_dapm_add_route, the previous
registered widget will overwritten by the latest same name widget,
will cause unexpect error. For Asoc framework we cant avoid this
situation and we cant decide which widget that wanted with route.
At least we can give users a notice.
Signed-off-by: Zhiwei Jiang <qq282012236@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Charles Keepax [Thu, 31 Jan 2019 13:30:18 +0000 (13:30 +0000)]
ASoC: dapm: Only power up active channels from a DAI
Currently all widgets attached to a DAI link will be powered
up when the DAI is active, however this may include routes
that are not actually in use if there are unused channels
available on the DAI.
The macros for creating AIF widgets already include an entry for
slot, it is proposed to change that to channel. The effective
difference here being respresenting the logical channel index
rather than the physical slot index. The CODECs currently
using the slot entry on the DAPM_AIF macros are using it in
a manner consistent with this, the CODECs not using it just
have the field set to zero.
A variable is added to snd_soc_dapm_widget to represent
this channel index and then for each AIF widget attached to
a DAI this is compared against the number of channels on
the stream. Enabling the links for those which will be in
use. This has the nice property that the CODECs which haven't
used the slot/channel entry in the macro will function exactly
as before due to all the AIF widgets having a channel of zero
and a stream by definition having at least one channel.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: topology: fix oops/use-after-free case with dai driver
rmmod/modprobe tests expose a kernel oops when accessing the dai
driver pointer. This comes from the topology design which operates in
multiple passes. Each object removal happens at a specific iteration,
and the code checks for the iteration (order) number after the memory
containing the order was freed.
Fix this be clearing a reference to the dai driver and check its
validity to avoid dereferences.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: dapm: fix use-after-free issue with dailink sname
Commit 7620fe9161ce ("ASoC: topology: fix memory leak in
soc_tplg_dapm_widget_create") fixed a memory leak issue, but
additional tests and KASAN reports show a use-after-free in soc-dapm.
The widgets are created with a kmemdup operating on a template. The
"name" string is also duplicated, but the "sname" string is not. As a
result, when the template is freed after widget creation, its sname
string is still used.
Fix by explicitly duplicating the "sname" string, and freeing it when
required.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound card need to judge that whether it is using
"TDM Split mode". To judge it and for other purpose, it has
rsnd_parse_connect_simple() and rsnd_parse_connect_graph(),
but these are using different judgement policy for
TDM Split mode.
It is pointless and confusable.
This patch add new rsnd_parse_tdm_split_mode() and use common
judgement policy for simple-card/audio-graph.
Without this patch, CTU will be judged as TDM Split mode
on audio-graph card.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: rsnd: synchronize connection check for simple-card/audio-graph
Current rsnd driver has below function to check connection
rsnd_parse_connect_simple()
rsnd_parse_connect_graph()
But these have different parameters. This patch synchronize these
for cleanup.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound device has many IPs and many situations.
If platform/board uses MIXer, situation will be more complex.
To avoid duplicate DVC kctrl registration when MIXer was used,
it had original flags.
But it was issue when sound card was re-binded, because
no one can't cleanup this flags then.
To solve this issue, commit 9c698e8481a15237a ("ASoC: rsnd: tidyup
registering method for rsnd_kctrl_new()") checks registered
card->controls, because if card was re-binded, these were cleanuped
automatically. This patch could solve re-binding issue.
But, it start to avoid MIX kctrl.
To solve these issues, we need below.
To avoid card re-binding issue: check registered card->controls
To avoid duplicate DVC registration: check registered rsnd_kctrl_cfg
To allow multiple MIX registration: check registered rsnd_kctrl_cfg
This patch do it.
Fixes: 9c698e8481a15237a ("ASoC: rsnd: tidyup registering method for rsnd_kctrl_new()") Reported-by: Jiada Wang <jiada_wang@mentor.com> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Tested-By: Jiada Wang <jiada_wang@mentor.com> Signed-off-by: Mark Brown <broonie@kernel.org>
The Spreadtrum DMA engine uses the link-list mode to support audio playback
or capture, thus this patch adds audio DMA platform support for CPU DAI to
trigger DMA link-list transfer.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
struct snd_soc_dapm_route has been modified to be a dynamic
object so that it can be used to save driver specific
data while parsing topology and clean up
driver-specific data during driver unloading.
This patch makes the following changes to accomplish the above:
1. Set the dobj member of snd_soc_dapm_route during the
SOC_TPLG_PASS_GRAPH pass of topology parsing.
2. Add the remove_route() routine that will be called while
removing all dynamic objects from the component driver.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: topology: add SND_SOC_DOBJ_GRAPH type for dapm routes
Add a new dobj type SND_SOC_DOBJ_GRAPH for dapm routes
and add snd_soc_dobj member to struct snd_soc_dapm_route.
This enables device drivers to save driver specific
data pertaining to dapm routes and also be able
to clean up the data when the driver module is unloaded.
Also, reorder the snd_soc_dobj_type types to align with
matching topology header types.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Currently when we unload and reload machine driver few times we end with
corrupted list and try to cleanup no longer existing objects. Fix this
by removing dobj from the list.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason we test if the machine is passed as a parameter before
fixing up the codec name. This is unnecessary, generates false
positives in static analysis tools and done only in this machine
driver, remove and adjust indentation.
Reported-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Cheng-Yi Chiang [Sat, 19 Jan 2019 11:33:33 +0000 (19:33 +0800)]
ASoC: cros_ec_codec: Add codec driver for Cros EC
Add a codec driver to control ChromeOS EC codec.
Use EC Host command to enable/disable I2S recording and control other
configurations.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org> Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Mark Brown <broonie@kernel.org>
CLASS-H controller/Amplifier is common accorss Qualcomm WCD codec series.
This patchset adds basic CLASS-H controller apis for WCD codecs after
wcd9335 to use.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Reviewed-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org>
Qualcomm WCD9335 Codec is a standalone Hi-Fi audio codec IC,
It supports both I2S/I2C and SLIMbus audio interfaces.
On slimbus interface it supports two data lanes; 16 Tx ports
and 8 Rx ports. It has Seven DACs and nine dedicated interpolators,
Seven (six audio ADCs, and one VBAT ADC), Multibutton headset
control (MBHC), Active noise cancellation and Sidetone paths
and processing.
This patchset adds very basic support for playback and capture
via the 9 interpolators and ADC respectively.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Reviewed-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates wcd9335 bindings with recommended properties.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: add helper to change platform name for all dailinks
To reuse the same machine drivers with Atom/SST, Skylake and SOF, we
need to change the default platform_name (or platforms->name in the
"modern" representation).
So far, this override was done with an automatic override, which was
broken by a set of changes for DT platforms related to deferred probe
handling.
This automatic override is actually not really needed, the machine
driver can already receive the platform name as a platform_data
parameter. This is used e.g. for HDaudio support where we have
different PCI aliases used for different platforms. We can reuse the
same mechanism and modify the machine drivers to override the dailinks
prior to registrating the card.
This will require additional work for SOF, but with this helper it'll
be just two lines of additional code per machine driver which is
reused, not the end of the world.
This helper can be simplified when all drivers have transitioned to
the "modern" representation of dailinks.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Yizhuo [Fri, 25 Jan 2019 18:45:37 +0000 (10:45 -0800)]
ASoC: rt5651: Variable "ret" in function rt5651_i2c_probe() could be uninitialized
In function rt5651_i2c_probe(), local variable "ret" could
be uninitialized if function regmap_read() returns -EINVAL.
However, this value is used in if statement. This is
potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu> Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: pcm512x: Fix clocking calculations when not using the PLL
The rationale behind the current calculation is somewhat obscure [1]
and can yield slightly wrong dividers in certain cases, which the
machine drivers for some boards (like the HiFiBerry DAC+ Pro)
seemingly try to circumvent, by updating the rate fraction so as to
suit this calculation.
The updated calculation should correctly yield the smallest bit clock
rate that would fit the frame.
ASoC: pcm512x: Implement the set_bclk_ratio interface
Some boards, such as the HiFiBerry DAC+ Pro, use a pair of external
oscillators, to generate 44.1 or 48kHz multiples and are forced to
resort to hacks [1] in order to support 24-bit data without ending up
with fractional dividers. This patch allows the machine driver to use
32-bit frames for 24-bit data to avoid such issues.
Although the datasheet (p. 15) seems to suggest that only a handful
of ratios are supported, it's not very explicit about it, so we allow
the full range of values supported by the underlying register in the
callback, to avoid needlessly rejecting potentially usable
configurations.
Linus Torvalds [Sun, 27 Jan 2019 20:02:00 +0000 (12:02 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for x86:
- Fix the swapped outb() parameters in the KASLR code
- Fix the PKEY handling at fork which missed to preserve the pkey
state for the child. Comes with a test case to validate that.
- Fix the entry stack handling for XEN PV to respect that XEN PV
systems enter the function already on the current thread stack and
not on the trampoline.
- Fix kexec load failure caused by using a stale value when the
kexec_buf structure is reused for subsequent allocations.
- Fix a bogus sizeof() in the memory encryption code
- Enforce PCI dependency for the Intel Low Power Subsystem
- Enforce PCI_LOCKLESS_CONFIG when PCI is enabled"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/Kconfig: Select PCI_LOCKLESS_CONFIG if PCI is enabled
x86/entry/64/compat: Fix stack switching for XEN PV
x86/kexec: Fix a kexec_file_load() failure
x86/mm/mem_encrypt: Fix erroneous sizeof()
x86/selftests/pkeys: Fork() to check for state being preserved
x86/pkeys: Properly copy pkey state at fork()
x86/kaslr: Fix incorrect i8254 outb() parameters
x86/intel/lpss: Make PCI dependency explicit
Linus Torvalds [Sun, 27 Jan 2019 19:57:46 +0000 (11:57 -0800)]
Merge branch 'x86-timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 timer fixes from Thomas Gleixner:
"Two commits which were missed to be sent during the merge window.
- The TSC calibration fix turns out to be more urgent as recent
Skylake-X systems seem to have massive trouble with calibration
disturbance. This should go back into stable for that reason and it
the risk of breakage is rather low.
- Drop an unused define"
* 'x86-timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hpet: Remove unused FSEC_PER_NSEC define
x86/tsc: Make calibration refinement more robust
Linus Torvalds [Sun, 27 Jan 2019 19:55:06 +0000 (11:55 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Glexiner:
"A single regression fix to address the unintended breakage of posix
cpu timers.
This is caused by a new sanity check in the common code, which fails
for posix cpu timers under certain conditions because the posix cpu
timer code never updates the variable which is checked"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-cpu-timers: Unbreak timer rearming
Linus Torvalds [Sun, 27 Jan 2019 19:25:38 +0000 (11:25 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A small set of fixes for the interrupt subsystem:
- Fix a double increment in the irq descriptor allocator which
resulted in a sanity check only being done for every second
affinity mask
- Add a missing device tree translation in the stm32-exti driver.
Without that the interrupt association is completely wrong.
- Initialize the mutex in the GIC-V3 MBI driver
- Fix the alignment for aliasing devices in the GIC-V3-ITS driver so
multi MSI allocations work correctly
- Ensure that the initial affinity of a interrupt is not empty at
startup time.
- Drop bogus include in the madera irq chip driver
- Fix KernelDoc regression"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Align PCI Multi-MSI allocation on their size
genirq/irqdesc: Fix double increment in alloc_descs()
genirq: Fix the kerneldoc comment for struct irq_affinity_desc
irqchip/madera: Drop GPIO includes
irqchip/gic-v3-mbi: Fix uninitialized mbi_lock
irqchip/stm32-exti: Add domain translate function
genirq: Make sure the initial affinity is not empty
Linus Torvalds [Sun, 27 Jan 2019 17:21:00 +0000 (09:21 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Quite a few fixes for x86: nested virtualization save/restore, AMD
nested virtualization and virtual APIC, 32-bit fixes, an important fix
to restore operation on older processors, and a bunch of hyper-v
bugfixes. Several are marked stable.
There are also fixes for GCC warnings and for a GCC/objtool interaction"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Mark expected switch fall-throughs
KVM: x86: fix TRACE_INCLUDE_PATH and remove -I. header search paths
KVM: selftests: check returned evmcs version range
x86/kvm/hyper-v: nested_enable_evmcs() sets vmcs_version incorrectly
KVM: VMX: Move vmx_vcpu_run()'s VM-Enter asm blob to a helper function
kvm: selftests: Fix region overlap check in kvm_util
kvm: vmx: fix some -Wmissing-prototypes warnings
KVM: nSVM: clear events pending from svm_complete_interrupts() when exiting to L1
svm: Fix AVIC incomplete IPI emulation
svm: Add warning message for AVIC IPI invalid target
KVM: x86: WARN_ONCE if sending a PV IPI returns a fatal error
KVM: x86: Fix PV IPIs for 32-bit KVM host
x86/kvm/hyper-v: recommend using eVMCS only when it is enabled
x86/kvm/hyper-v: don't recommend doing reset via synthetic MSR
kvm: x86/vmx: Use kzalloc for cached_vmcs12
KVM: VMX: Use the correct field var when clearing VM_ENTRY_LOAD_IA32_PERF_GLOBAL_CTRL
KVM: x86: Fix single-step debugging
x86/kvm/hyper-v: don't announce GUEST IDLE MSR support
projects / mirror_ubuntu-eoan-kernel.git / log