Shirish S [Tue, 4 Jun 2019 15:55:03 +0000 (21:25 +0530)]
drm/amdgpu/{uvd,vcn}: fetch ring's read_ptr after alloc
[What]
readptr read always returns zero, since most likely
these blocks are either power or clock gated.
[How]
fetch rptr after amdgpu_ring_alloc() which informs
the power management code that the block is about to be
used and hence the gating is turned off.
Signed-off-by: Louis Li <Ching-shih.Li@amd.com> Signed-off-by: Shirish S <shirish.s@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Dave Airlie [Fri, 7 Jun 2019 07:14:19 +0000 (17:14 +1000)]
Merge branch 'linux-5.2' of git://github.com/skeggsb/linux into drm-fixes
" This is a bit more than I'd like to be pushing at this point in a
cycle, but it's a fairly important issue. There's been numerous
reports of more recent GP10[2467] boards failing to load, and I've
worked with NVIDIA FW engineers and tracked this down to the FW we've
been using not properly supporting the boards in question.
I've pushed an update to linux-firmware with the new FW version, which
unfortunately contains API changes vs the older firmware.
This series teaches the ACR subsystem inside nouveau enough to be able
to deal with supporting multiple incompatible FW revisions, and adds
support to the relevant chipsets for loading the newer FW revision, if
it's available."
drm/komeda: remove set but not used variable 'kcrtc'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/arm/display/komeda/komeda_plane.c: In function komeda_plane_atomic_check:
drivers/gpu/drm/arm/display/komeda/komeda_plane.c:49:22: warning: variable kcrtc set but not used [-Wunused-but-set-variable]
It is never used since introduction in
commit 9e5603094176 ("drm/komeda: Add komeda_plane/plane_helper_funcs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com> Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Louis Li [Fri, 24 May 2019 22:39:47 +0000 (06:39 +0800)]
drm/amdgpu: fix ring test failure issue during s3 in vce 3.0 (V2)
[What]
vce ring test fails consistently during resume in s3 cycle, due to
mismatch read & write pointers.
On debug/analysis its found that rptr to be compared is not being
correctly updated/read, which leads to this failure.
Below is the failure signature:
[drm:amdgpu_vce_ring_test_ring] *ERROR* amdgpu: ring 12 test failed
[drm:amdgpu_device_ip_resume_phase2] *ERROR* resume of IP block <vce_v3_0> failed -110
[drm:amdgpu_device_resume] *ERROR* amdgpu_device_ip_resume failed (-110).
[How]
fetch rptr appropriately, meaning move its read location further down
in the code flow.
With this patch applied the s3 failure is no more seen for >5k s3 cycles,
which otherwise is pretty consistent.
V2: remove reduntant fetch of rptr
Signed-off-by: Louis Li <Ching-shih.Li@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Robin Murphy [Fri, 17 May 2019 16:37:22 +0000 (17:37 +0100)]
drm/arm/hdlcd: Allow a bit of clock tolerance
On the Arm Juno platform, the HDLCD pixel clock is constrained to 250KHz
resolution in order to avoid the tiny System Control Processor spending
aeons trying to calculate exact PLL coefficients. This means that modes
like my oddball 1600x1200 with 130.89MHz clock get rejected since the
rate cannot be matched exactly. In practice, though, this mode works
quite happily with the clock at 131MHz, so let's relax the check to
allow a little bit of slop.
Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Robin Murphy [Fri, 17 May 2019 16:37:21 +0000 (17:37 +0100)]
drm/arm/hdlcd: Actually validate CRTC modes
Rather than allowing any old mode through, then subsequently refusing
unmatchable clock rates in atomic_check when it's too late to back out
and pick a different mode, let's do that validation up-front where it
will cause unsupported modes to be correctly pruned in the first place.
This also eliminates an issue whereby a perceived clock rate of 0 would
cause atomic disable to fail and prevent the module from being unloaded.
Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Wen He [Wed, 8 May 2019 10:58:18 +0000 (10:58 +0000)]
drm/arm/mali-dp: Add a loop around the second set CVAL and try 5 times
This patch trying to fix monitor freeze issue caused by drm error
'flip_done timed out' on LS1028A platform. this set try is make a loop
around the second setting CVAL and try like 5 times before giveing up.
Signed-off-by: Wen He <wen.he_1@nxp.com> Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
drm/komeda: fixing of DMA mapping sg segment warning
Fixing the DMA mapping sg segment warning, which shows "DMA-API: mapping
sg segment longer than device claims to support [len=921600] [max=65536]".
Fixed by setting the max segment size at Komeda driver.
This patch depends on:
- https://patchwork.freedesktop.org/series/54448/
- https://patchwork.freedesktop.org/series/54449/
- https://patchwork.freedesktop.org/series/54450/
- https://patchwork.freedesktop.org/series/58976/
Changes since v1:
- Adds member description
- Adds patch denpendency in the comment
Signed-off-by: Lowry Li (Arm Technology China) <lowry.li@arm.com> Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com> Reviewed-by: Ayan Kumar Halder <ayan.halder@arm.com> Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Helen Koike [Mon, 3 Jun 2019 16:56:10 +0000 (13:56 -0300)]
drm: don't block fb changes for async plane updates
In the case of a normal sync update, the preparation of framebuffers (be
it calling drm_atomic_helper_prepare_planes() or doing setups with
drm_framebuffer_get()) are performed in the new_state and the respective
cleanups are performed in the old_state.
In the case of async updates, the preparation is also done in the
new_state but the cleanups are done in the new_state (because updates
are performed in place, i.e. in the current state).
The current code blocks async udpates when the fb is changed, turning
async updates into sync updates, slowing down cursor updates and
introducing regressions in igt tests with errors of type:
"CRITICAL: completed 97 cursor updated in a period of 30 flips, we
expect to complete approximately 15360 updates, with the threshold set
at 7680"
Fb changes in async updates were prevented to avoid the following scenario:
- Async update, oldfb = NULL, newfb = fb1, prepare fb1, cleanup fb1
- Async update, oldfb = fb1, newfb = fb2, prepare fb2, cleanup fb2
- Non-async commit, oldfb = fb2, newfb = fb1, prepare fb1, cleanup fb2 (wrong)
Where we have a single call to prepare fb2 but double cleanup call to fb2.
To solve the above problems, instead of blocking async fb changes, we
place the old framebuffer in the new_state object, so when the code
performs cleanups in the new_state it will cleanup the old_fb and we
will have the following scenario instead:
Helen Koike [Mon, 3 Jun 2019 16:56:09 +0000 (13:56 -0300)]
drm/vc4: fix fb references in async update
Async update callbacks are expected to set the old_fb in the new_state
so prepare/cleanup framebuffers are balanced.
Calling drm_atomic_set_fb_for_plane() (which gets a reference of the new
fb and put the old fb) is not required, as it's taken care by
drm_mode_cursor_universal() when calling drm_atomic_helper_update_plane().
Cc: <stable@vger.kernel.org> # v4.19+ Fixes: 539c320bfa97 ("drm/vc4: update cursors asynchronously through atomic") Suggested-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Helen Koike <helen.koike@collabora.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190603165610.24614-5-helen.koike@collabora.com
Helen Koike [Mon, 3 Jun 2019 16:56:08 +0000 (13:56 -0300)]
drm/msm: fix fb references in async update
Async update callbacks are expected to set the old_fb in the new_state
so prepare/cleanup framebuffers are balanced.
Cc: <stable@vger.kernel.org> # v4.14+ Fixes: 224a4c970987 ("drm/msm: update cursors asynchronously through atomic") Suggested-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Helen Koike <helen.koike@collabora.com> Acked-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190603165610.24614-4-helen.koike@collabora.com
Helen Koike [Mon, 3 Jun 2019 16:56:07 +0000 (13:56 -0300)]
drm/amd: fix fb references in async update
Async update callbacks are expected to set the old_fb in the new_state
so prepare/cleanup framebuffers are balanced.
Calling drm_atomic_set_fb_for_plane() (which gets a reference of the new
fb and put the old fb) is not required, as it's taken care by
drm_mode_cursor_universal() when calling drm_atomic_helper_update_plane().
Cc: <stable@vger.kernel.org> # v4.20+ Fixes: 674e78acae0d ("drm/amd/display: Add fast path for cursor plane updates") Suggested-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Helen Koike <helen.koike@collabora.com> Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190603165610.24614-3-helen.koike@collabora.com
Helen Koike [Mon, 3 Jun 2019 16:56:06 +0000 (13:56 -0300)]
drm/rockchip: fix fb references in async update
In the case of async update, modifications are done in place, i.e. in the
current plane state, so the new_state is prepared and the new_state is
cleaned up (instead of the old_state, unlike what happens in a
normal sync update).
To cleanup the old_fb properly, it needs to be placed in the new_state
in the end of async_update, so cleanup call will unreference the old_fb
correctly.
if (plane->state->fb && plane->state->fb != new_state->fb) {
...
}
Which was wrong, as the fb were just assigned to be equal, so this if
statement nevers evaluates to true.
Another details is that the function drm_crtc_vblank_get() can only be
called when vop->is_enabled is true, otherwise it has no effect and
trows a WARN_ON().
Calling drm_atomic_set_fb_for_plane() (which get a referent of the new
fb and pus the old fb) is not required, as it is taken care by
drm_mode_cursor_universal() when calling
drm_atomic_helper_update_plane().
Xiaolin Zhang [Mon, 3 Jun 2019 02:55:53 +0000 (10:55 +0800)]
drm/i915/gvt: save RING_HEAD into vreg when vgpu switched out
Save RING_HEAD into vgpu reg when vgpu switched out and report
it's value back to guest.
v6: addressed comment for ring head wrap count support. (Zhenyu)
v5: ring head wrap count support.
v4: updated HEAD/TAIL with guest value, not host value. (Yan Zhao)
v3: save RING HEAD/TAIL vgpu reg in save_ring_hw_state. (Zhenyu Wang)
v2: save RING_TAIL as well during vgpu mmio switch to meet ring_is_idle
condition. (Fred Gao)
v1: based on input from Weinan. (Weinan Li)
[zhenyuw: Include this fix for possible future guest kernel that
would utilize RING_HEAD for hangcheck.]
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Xiaolin Zhang <xiaolin.zhang@intel.com> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Weinan Li [Fri, 31 May 2019 07:33:48 +0000 (15:33 +0800)]
drm/i915/gvt: add F_CMD_ACCESS flag for wa regs
Instead of updating by MMIO write, all of the wa regs are initialized by
wa_ctx. From host side, it should make this behavior as expected, add
'F_CMD_ACCESS' flag to these regs and allow access by commands.
Linus Torvalds [Sun, 2 Jun 2019 18:10:01 +0000 (11:10 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Two fixes: a quirk for KVM guests running on certain AMD CPUs, and a
KASAN related build fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/CPU/AMD: Don't force the CPB cap when running under a hypervisor
x86/boot: Provide KASAN compatible aliases for string routines
Linus Torvalds [Sun, 2 Jun 2019 18:08:12 +0000 (11:08 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"On the kernel side there's a bunch of ring-buffer ordering fixes for a
reproducible bug, plus a PEBS constraints regression fix.
Plus tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools headers UAPI: Sync kvm.h headers with the kernel sources
perf record: Fix s390 missing module symbol and warning for non-root users
perf machine: Read also the end of the kernel
perf test vmlinux-kallsyms: Ignore aliases to _etext when searching on kallsyms
perf session: Add missing swap ops for namespace events
perf namespace: Protect reading thread's namespace
tools headers UAPI: Sync drm/drm.h with the kernel
tools headers UAPI: Sync drm/i915_drm.h with the kernel
tools headers UAPI: Sync linux/fs.h with the kernel
tools headers UAPI: Sync linux/sched.h with the kernel
tools arch x86: Sync asm/cpufeatures.h with the with the kernel
tools include UAPI: Update copy of files related to new fspick, fsmount, fsconfig, fsopen, move_mount and open_tree syscalls
perf arm64: Fix mksyscalltbl when system kernel headers are ahead of the kernel
perf data: Fix 'strncat may truncate' build failure with recent gcc
perf/ring-buffer: Use regular variables for nesting
perf/ring-buffer: Always use {READ,WRITE}_ONCE() for rb->user_page data
perf/ring_buffer: Add ordering to rb->nest increment
perf/ring_buffer: Fix exposing a temporarily decreased data_head
perf/x86/intel/ds: Fix EVENT vs. UEVENT PEBS constraints
Linus Torvalds [Sun, 2 Jun 2019 18:06:13 +0000 (11:06 -0700)]
Merge branch 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"Two EFI fixes: a quirk for weird systabs, plus add more robust error
handling in the old 1:1 mapping code"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Allow the number of EFI configuration tables entries to be zero
efi/x86/Add missing error handling to old_memmap 1:1 mapping code
Linus Torvalds [Sun, 2 Jun 2019 17:22:38 +0000 (10:22 -0700)]
Merge tag 'spdx-5.2-rc3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull SPDX fixes from Greg KH:
"Here are just two small patches, that fix up some found SPDX
identifier issues.
The first patch fixes an error in a previous SPDX fixup patch, that
causes build errors when doing 'make clean' on the tree (the fact that
almost no one noticed it reflects the fact that kernel developers
don't like doing that option very often...)
The second patch fixes up a number of places in the tree where people
mistyped the string "SPDX-License-Identifier". Given that people can
not even type their own name all the time without mistakes, this was
bound to happen, and odds are, we will have to add some type of check
for this to checkpatch.pl to catch this happening in the future.
Both of these have passed testing by 0-day"
* tag 'spdx-5.2-rc3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
treewide: fix typos of SPDX-License-Identifier
crypto: ux500 - fix license comment syntax error
Linus Torvalds [Sun, 2 Jun 2019 17:21:04 +0000 (10:21 -0700)]
Merge tag 'powerpc-5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A minor fix to our IMC PMU code to print a less confusing error
message when the driver can't initialise properly.
A fix for a bug where a user requesting an unsupported branch sampling
filter can corrupt PMU state, preventing the PMU from counting
properly.
And finally a fix for a bug in our support for kexec_file_load(),
which prevented loading a kernel and initramfs. Most versions of kexec
don't yet use kexec_file_load().
Thanks to: Anju T Sudhakar, Dave Young, Madhavan Srinivasan, Ravi
Bangoria, Thiago Jung Bauermann"
* tag 'powerpc-5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/kexec: Fix loading of kernel + initramfs with kexec_file_load()
powerpc/perf: Fix MMCRA corruption by bhrb_filter
powerpc/powernv: Return for invalid IMC domain
Linus Torvalds [Sun, 2 Jun 2019 17:19:39 +0000 (10:19 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Fixes for PPC and s390"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Book3S HV: Restore SPRG3 in kvmhv_p9_guest_entry()
KVM: PPC: Book3S HV: Fix lockdep warning when entering guest on POWER9
KVM: PPC: Book3S HV: XIVE: Fix page offset when clearing ESB pages
KVM: PPC: Book3S HV: XIVE: Take the srcu read lock when accessing memslots
KVM: PPC: Book3S HV: XIVE: Do not clear IRQ data of passthrough interrupts
KVM: PPC: Book3S HV: XIVE: Introduce a new mutex for the XIVE device
KVM: PPC: Book3S HV: XIVE: Fix the enforced limit on the vCPU identifier
KVM: PPC: Book3S HV: XIVE: Do not test the EQ flag validity when resetting
KVM: PPC: Book3S HV: XIVE: Clear file mapping when device is released
KVM: PPC: Book3S HV: Don't take kvm->lock around kvm_for_each_vcpu
KVM: PPC: Book3S: Use new mutex to synchronize access to rtas token list
KVM: PPC: Book3S HV: Use new mutex to synchronize MMU setup
KVM: PPC: Book3S HV: Avoid touching arch.mmu_ready in XIVE release functions
KVM: s390: Do not report unusabled IDs via KVM_CAP_MAX_VCPU_ID
kvm: fix compile on s390 part 2
Linus Torvalds [Sun, 2 Jun 2019 17:16:09 +0000 (10:16 -0700)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal SoC fix from Eduardo Valentin:
"A single revert, detected to cause issues on the tsens driver"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
Revert "drivers: thermal: tsens: Add new operation to check if a sensor is enabled"
Linus Torvalds [Sun, 2 Jun 2019 17:14:25 +0000 (10:14 -0700)]
Merge tag 'led-fixes-for-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fix from Jacek Anaszewski:
"Fix for a recent change in LED core, that didn't take into account the
possibility of calling led_blink_setup() from atomic context"
* tag 'led-fixes-for-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: avoid flush_work in atomic context
Linus Torvalds [Sun, 2 Jun 2019 16:26:34 +0000 (09:26 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six minor fixes to device drivers and one to the multipath alua
handler.
The most extensive fix is the zfcp port remove prevention one, but
it's impact is only s390"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: libsas: delete sas port if expander discover failed
scsi: libsas: only clear phy->in_shutdown after shutdown event done
scsi: scsi_dh_alua: Fix possible null-ptr-deref
scsi: smartpqi: properly set both the DMA mask and the coherent DMA mask
scsi: zfcp: fix to prevent port_remove with pure auto scan LUNs (only sdevs)
scsi: zfcp: fix missing zfcp_port reference put on -EBUSY from port_remove
scsi: libcxgbi: add a check for NULL pointer in cxgbi_check_route()
Linus Torvalds [Sun, 2 Jun 2019 15:51:30 +0000 (08:51 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"Various fixes and followups"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm, compaction: make sure we isolate a valid PFN
include/linux/generic-radix-tree.h: fix kerneldoc comment
kernel/signal.c: trace_signal_deliver when signal_group_exit
drivers/iommu/intel-iommu.c: fix variable 'iommu' set but not used
spdxcheck.py: fix directory structures
kasan: initialize tag to 0xff in __kasan_kmalloc
z3fold: fix sheduling while atomic
scripts/gdb: fix invocation when CONFIG_COMMON_CLK is not set
mm/gup: continue VM_FAULT_RETRY processing even for pre-faults
ocfs2: fix error path kobject memory leak
memcg: make it work on sparse non-0-node systems
mm, memcg: consider subtrees in memory.events
prctl_set_mm: downgrade mmap_sem to read lock
prctl_set_mm: refactor checks from validate_prctl_map
kernel/fork.c: make max_threads symbol static
arch/arm/boot/compressed/decompress.c: fix build error due to lz4 changes
arch/parisc/configs/c8000_defconfig: remove obsoleted CONFIG_DEBUG_SLAB_LEAK
mm/vmalloc.c: fix typo in comment
lib/sort.c: fix kernel-doc notation warnings
mm: fix Documentation/vm/hmm.rst Sphinx warnings
When we have holes in a normal memory zone, we could endup having
cached_migrate_pfns which may not necessarily be valid, under heavy memory
pressure with swapping enabled ( via __reset_isolation_suitable(),
triggered by kswapd).
Later if we fail to find a page via fast_isolate_freepages(), we may end
up using the migrate_pfn we started the search with, as valid page. This
could lead to accessing NULL pointer derefernces like below, due to an
invalid mem_section pointer.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008 [47/1825]
Mem abort info:
ESR = 0x96000004
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp = 0000000082f94ae9
[0000000000000008] pgd=0000000000000000
Internal error: Oops: 96000004 [#1] SMP
...
CPU: 10 PID: 6080 Comm: qemu-system-aar Not tainted 510-rc1+ #6
Hardware name: AmpereComputing(R) OSPREY EV-883832-X3-0001/OSPREY, BIOS 4819 09/25/2018
pstate: 60000005 (nZCv daif -PAN -UAO)
pc : set_pfnblock_flags_mask+0x58/0xe8
lr : compaction_alloc+0x300/0x950
[...]
Process qemu-system-aar (pid: 6080, stack limit = 0x0000000095070da5)
Call trace:
set_pfnblock_flags_mask+0x58/0xe8
compaction_alloc+0x300/0x950
migrate_pages+0x1a4/0xbb0
compact_zone+0x750/0xde8
compact_zone_order+0xd8/0x118
try_to_compact_pages+0xb4/0x290
__alloc_pages_direct_compact+0x84/0x1e0
__alloc_pages_nodemask+0x5e0/0xe18
alloc_pages_vma+0x1cc/0x210
do_huge_pmd_anonymous_page+0x108/0x7c8
__handle_mm_fault+0xdd4/0x1190
handle_mm_fault+0x114/0x1c0
__get_user_pages+0x198/0x3c0
get_user_pages_unlocked+0xb4/0x1d8
__gfn_to_pfn_memslot+0x12c/0x3b8
gfn_to_pfn_prot+0x4c/0x60
kvm_handle_guest_abort+0x4b0/0xcd8
handle_exit+0x140/0x1b8
kvm_arch_vcpu_ioctl_run+0x260/0x768
kvm_vcpu_ioctl+0x490/0x898
do_vfs_ioctl+0xc4/0x898
ksys_ioctl+0x8c/0xa0
__arm64_sys_ioctl+0x28/0x38
el0_svc_common+0x74/0x118
el0_svc_handler+0x38/0x78
el0_svc+0x8/0xc
Code: f8607840f100001f8b0114019a801020 (f9400400)
---[ end trace af6a35219325a9b6 ]---
The issue was reported on an arm64 server with 128GB with holes in the
zone (e.g, [32GB@4GB, 96GB@544GB]), with a swap device enabled, while
running 100 KVM guest instances.
This patch fixes the issue by ensuring that the page belongs to a valid
PFN when we fallback to using the lower limit of the scan range upon
failure in fast_isolate_freepages().
Link: http://lkml.kernel.org/r/1558711908-15688-1-git-send-email-suzuki.poulose@arm.com Fixes: 5a811889de10f1eb ("mm, compaction: use free lists to quickly locate a migration target") Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Reported-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Mel Gorman <mgorman@techsingularity.net> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Qian Cai <cai@lca.pw> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zhenliang Wei [Sat, 1 Jun 2019 05:30:52 +0000 (22:30 -0700)]
kernel/signal.c: trace_signal_deliver when signal_group_exit
In the fixes commit, removing SIGKILL from each thread signal mask and
executing "goto fatal" directly will skip the call to
"trace_signal_deliver". At this point, the delivery tracking of the
SIGKILL signal will be inaccurate.
Therefore, we need to add trace_signal_deliver before "goto fatal" after
executing sigdelset.
Note: SEND_SIG_NOINFO matches the fact that SIGKILL doesn't have any info.
Link: http://lkml.kernel.org/r/20190425025812.91424-1-weizhenliang@huawei.com Fixes: cf43a757fd4944 ("signal: Restore the stop PTRACE_EVENT_EXIT") Signed-off-by: Zhenliang Wei <weizhenliang@huawei.com> Reviewed-by: Christian Brauner <christian@brauner.io> Reviewed-by: Oleg Nesterov <oleg@redhat.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Ivan Delalande <colona@arista.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Deepa Dinamani <deepa.kernel@gmail.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Qian Cai [Sat, 1 Jun 2019 05:30:49 +0000 (22:30 -0700)]
drivers/iommu/intel-iommu.c: fix variable 'iommu' set but not used
Commit cf04eee8bf0e ("iommu/vt-d: Include ACPI devices in iommu=pt")
added for_each_active_iommu() in iommu_prepare_static_identity_mapping()
but never used the each element, i.e, "drhd->iommu".
drivers/iommu/intel-iommu.c: In function
'iommu_prepare_static_identity_mapping':
drivers/iommu/intel-iommu.c:3037:22: warning: variable 'iommu' set but
not used [-Wunused-but-set-variable]
struct intel_iommu *iommu;
Fixed the warning by appending a compiler attribute __maybe_unused for it.
Link: http://lkml.kernel.org/r/20190523013314.2732-1-cai@lca.pw Signed-off-by: Qian Cai <cai@lca.pw> Suggested-by: Andrew Morton <akpm@linux-foundation.org> Cc: Joerg Roedel <jroedel@suse.de> Cc: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The LICENSE directory has recently changed structure and this makes
spdxcheck fails as per below:
FAIL: "Blob or Tree named 'other' not found"
Traceback (most recent call last):
File "scripts/spdxcheck.py", line 240, in <module>
spdx = read_spdxdata(repo)
File "scripts/spdxcheck.py", line 41, in read_spdxdata
for el in lictree[d].traverse():
[...]
KeyError: "Blob or Tree named 'other' not found"
Fix the script to restore the correctness on checkpatch License checking.
References: 62be257e986d ("LICENSES: Rename other to deprecated")
References: 8ea8814fcdcb ("LICENSES: Clearly mark dual license only licenses") Link: http://lkml.kernel.org/r/20190523084755.56739-1-vincenzo.frascino@arm.com Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Joe Perches <joe@perches.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jeremy Cline <jcline@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When building with -Wuninitialized and CONFIG_KASAN_SW_TAGS unset, Clang
warns:
mm/kasan/common.c:484:40: warning: variable 'tag' is uninitialized when
used here [-Wuninitialized]
kasan_unpoison_shadow(set_tag(object, tag), size);
^~~
set_tag ignores tag in this configuration but clang doesn't realize it at
this point in its pipeline, as it points to arch_kasan_set_tag as being
the point where it is used, which will later be expanded to (void
*)(object) without a use of tag. Initialize tag to 0xff, as it removes
this warning and doesn't change the meaning of the code.
Fabiano Rosas [Sat, 1 Jun 2019 05:30:36 +0000 (22:30 -0700)]
scripts/gdb: fix invocation when CONFIG_COMMON_CLK is not set
CLK_GET_RATE_NOCACHE depends on CONFIG_COMMON_CLK. Importing constants.py
when CONFIG_COMMON_CLK is not defined causes:
(gdb) lx-symbols
(...)
File "scripts/gdb/linux/proc.py", line 15, in <module>
from linux import constants
File "scripts/gdb/linux/constants.py", line 2, in <module>
LX_CLK_GET_RATE_NOCACHE = gdb.parse_and_eval("CLK_GET_RATE_NOCACHE")
gdb.error: No symbol "CLK_GET_RATE_NOCACHE" in current context.
Link: http://lkml.kernel.org/r/20190523195313.24701-1-farosas@linux.ibm.com Fixes: e7e6f462c1be ("scripts/gdb: print cached rate in lx-clk-summary") Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: Kieran Bingham <kbingham@kernel.org> Cc: Leonard Crestez <leonard.crestez@nxp.com> Cc: Jackie Liu <liuyun01@kylinos.cn> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Rapoport [Sat, 1 Jun 2019 05:30:33 +0000 (22:30 -0700)]
mm/gup: continue VM_FAULT_RETRY processing even for pre-faults
When get_user_pages*() is called with pages = NULL, the processing of
VM_FAULT_RETRY terminates early without actually retrying to fault-in all
the pages.
If the pages in the requested range belong to a VMA that has userfaultfd
registered, handle_userfault() returns VM_FAULT_RETRY *after* user space
has populated the page, but for the gup pre-fault case there's no actual
retry and the caller will get no pages although they are present.
This issue was uncovered when running post-copy memory restore in CRIU
after d9c9ce34ed5c ("x86/fpu: Fault-in user stack if
copy_fpstate_to_sigframe() fails").
After this change, the copying of FPU state to the sigframe switched from
copy_to_user() variants which caused a real page fault to get_user_pages()
with pages parameter set to NULL.
In post-copy mode of CRIU, the destination memory is managed with
userfaultfd and lack of the retry for pre-fault case in get_user_pages()
causes a crash of the restored process.
Making the pre-fault behavior of get_user_pages() the same as the "normal"
one fixes the issue.
Link: http://lkml.kernel.org/r/1557844195-18882-1-git-send-email-rppt@linux.ibm.com Fixes: d9c9ce34ed5c ("x86/fpu: Fault-in user stack if copy_fpstate_to_sigframe() fails") Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Tested-by: Andrei Vagin <avagin@gmail.com> [https://travis-ci.org/avagin/linux/builds/533184940] Tested-by: Hugh Dickins <hughd@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Borislav Petkov <bp@suse.de> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a call to kobject_init_and_add() fails we should call kobject_put()
otherwise we leak memory.
Add call to kobject_put() in the error path of call to
kobject_init_and_add(). Please note, this has the side effect that the
release method is called if kobject_init_and_add() fails.
Link: http://lkml.kernel.org/r/20190513033458.2824-1-tobin@kernel.org Signed-off-by: Tobin C. Harding <tobin@kernel.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Sat, 1 Jun 2019 05:30:26 +0000 (22:30 -0700)]
memcg: make it work on sparse non-0-node systems
We have a single node system with node 0 disabled:
Scanning NUMA topology in Northbridge 24
Number of physical nodes 2
Skipping disabled node 0
Node 1 MemBase 0000000000000000 Limit 00000000fbff0000
NODE_DATA(1) allocated [mem 0xfbfda000-0xfbfeffff]
This causes crashes in memcg when system boots:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
#PF error: [normal kernel read fault]
...
RIP: 0010:list_lru_add+0x94/0x170
...
Call Trace:
d_lru_add+0x44/0x50
dput.part.34+0xfc/0x110
__fput+0x108/0x230
task_work_run+0x9f/0xc0
exit_to_usermode_loop+0xf5/0x100
It is reproducible as far as 4.12. I did not try older kernels. You have
to have a new enough systemd, e.g. 241 (the reason is unknown -- was not
investigated). Cannot be reproduced with systemd 234.
The system crashes because the size of lru array is never updated in
memcg_update_all_list_lrus and the reads are past the zero-sized array,
causing dereferences of random memory.
The root cause are list_lru_memcg_aware checks in the list_lru code. The
test in list_lru_memcg_aware is broken: it assumes node 0 is always
present, but it is not true on some systems as can be seen above.
So fix this by avoiding checks on node 0. Remember the memcg-awareness by
a bool flag in struct list_lru.
Link: http://lkml.kernel.org/r/20190522091940.3615-1-jslaby@suse.cz Fixes: 60d3fd32a7a9 ("list_lru: introduce per-memcg lists") Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Michal Hocko <mhocko@suse.com> Suggested-by: Vladimir Davydov <vdavydov.dev@gmail.com> Acked-by: Vladimir Davydov <vdavydov.dev@gmail.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chris Down [Sat, 1 Jun 2019 05:30:22 +0000 (22:30 -0700)]
mm, memcg: consider subtrees in memory.events
memory.stat and other files already consider subtrees in their output, and
we should too in order to not present an inconsistent interface.
The current situation is fairly confusing, because people interacting with
cgroups expect hierarchical behaviour in the vein of memory.stat,
cgroup.events, and other files. For example, this causes confusion when
debugging reclaim events under low, as currently these always read "0" at
non-leaf memcg nodes, which frequently causes people to misdiagnose breach
behaviour. The same confusion applies to other counters in this file when
debugging issues.
Aggregation is done at write time instead of at read-time since these
counters aren't hot (unlike memory.stat which is per-page, so it does it
at read time), and it makes sense to bundle this with the file
notifications.
After this patch, events are propagated up the hierarchy:
[root@ktst ~]# cat /sys/fs/cgroup/system.slice/memory.events
low 0
high 0
max 0
oom 0
oom_kill 0
[root@ktst ~]# systemd-run -p MemoryMax=1 true
Running as unit: run-r251162a189fb4562b9dabfdc9b0422f5.service
[root@ktst ~]# cat /sys/fs/cgroup/system.slice/memory.events
low 0
high 0
max 7
oom 1
oom_kill 1
As this is a change in behaviour, this can be reverted to the old
behaviour by mounting with the `memory_localevents' flag set. However, we
use the new behaviour by default as there's a lack of evidence that there
are any current users of memory.events that would find this change
undesirable.
akpm: this is a behaviour change, so Cc:stable. THis is so that
forthcoming distros which use cgroup v2 are more likely to pick up the
revised behaviour.
Link: http://lkml.kernel.org/r/20190208224419.GA24772@chrisdown.name Signed-off-by: Chris Down <chris@chrisdown.name> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Shakeel Butt <shakeelb@google.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Tejun Heo <tj@kernel.org> Cc: Roman Gushchin <guro@fb.com> Cc: Dennis Zhou <dennis@kernel.org> Cc: Suren Baghdasaryan <surenb@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Koutný [Sat, 1 Jun 2019 05:30:19 +0000 (22:30 -0700)]
prctl_set_mm: downgrade mmap_sem to read lock
The commit a3b609ef9f8b ("proc read mm's {arg,env}_{start,end} with mmap
semaphore taken.") added synchronization of reading argument/environment
boundaries under mmap_sem. Later commit 88aa7cc688d4 ("mm: introduce
arg_lock to protect arg_start|end and env_start|end in mm_struct") avoided
the coarse use of mmap_sem in similar situations. But there still
remained two places that (mis)use mmap_sem.
get_cmdline should also use arg_lock instead of mmap_sem when it reads the
boundaries.
The second place that should use arg_lock is in prctl_set_mm. By
protecting the boundaries fields with the arg_lock, we can downgrade
mmap_sem to reader lock (analogous to what we already do in
prctl_set_mm_map).
[akpm@linux-foundation.org: coding style fixes] Link: http://lkml.kernel.org/r/20190502125203.24014-3-mkoutny@suse.com Fixes: 88aa7cc688d4 ("mm: introduce arg_lock to protect arg_start|end and env_start|end in mm_struct") Signed-off-by: Michal Koutný <mkoutny@suse.com> Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com> Co-developed-by: Laurent Dufour <ldufour@linux.ibm.com> Reviewed-by: Cyrill Gorcunov <gorcunov@gmail.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Yang Shi <yang.shi@linux.alibaba.com> Cc: Mateusz Guzik <mguzik@redhat.com> Cc: Kirill Tkhai <ktkhai@virtuozzo.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Koutný [Sat, 1 Jun 2019 05:30:16 +0000 (22:30 -0700)]
prctl_set_mm: refactor checks from validate_prctl_map
Despite comment of validate_prctl_map claims there are no capability
checks, it is not completely true since commit 4d28df6152aa ("prctl: Allow
local CAP_SYS_ADMIN changing exe_file"). Extract the check out of the
function and make the function perform purely arithmetic checks.
This patch should not change any behavior, it is mere refactoring for
following patch.
[akpm@linux-foundation.org: coding style fixes] Link: http://lkml.kernel.org/r/20190502125203.24014-2-mkoutny@suse.com Signed-off-by: Michal Koutný <mkoutny@suse.com> Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com> Reviewed-by: Cyrill Gorcunov <gorcunov@gmail.com> Cc: Kirill Tkhai <ktkhai@virtuozzo.com> Cc: Laurent Dufour <ldufour@linux.ibm.com> Cc: Mateusz Guzik <mguzik@redhat.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Yang Shi <yang.shi@linux.alibaba.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arch/arm/boot/compressed/decompress.c: fix build error due to lz4 changes
include/linux/cpumask.h: In function 'cpumask_parse':
include/linux/cpumask.h:636:21: error: implicit declaration of function 'strchrnul'; did you mean 'strchr'? [-Werror=implicit-function-declaration]
Because arch/arm/boot/compressed/decompress.c does
#define _LINUX_STRING_H_
preventing linux/string.h from providing strchrnul. It also #includes
asm/string.h, which for arm has a declaration of strchr(), explaining why
this didn't use to fail.
Link: http://lkml.kernel.org/r/20190528115346.f5a7kn3hdnuf5rts@linutronix.de Fixes: 3713a4e1fdb8d ("include/linux/cpumask.h: fix double string traverse in cpumask_parse") Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Cc: Yury Norov <ynorov@marvell.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Sat, 1 Jun 2019 05:30:00 +0000 (22:30 -0700)]
lib/sort.c: fix kernel-doc notation warnings
Fix kernel-doc notation in lib/sort.c by using correct function parameter
names.
lib/sort.c:59: warning: Excess function parameter 'size' description in 'swap_words_32'
lib/sort.c:83: warning: Excess function parameter 'size' description in 'swap_words_64'
lib/sort.c:110: warning: Excess function parameter 'size' description in 'swap_bytes'
Link: http://lkml.kernel.org/r/60e25d3d-68d1-bde2-3b39-e4baa0b14907@infradead.org Fixes: 37d0ec34d111a ("lib/sort: make swap functions more generic") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: George Spelvin <lkml@sdf.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Masahiro Yamada [Sat, 1 Jun 2019 03:22:42 +0000 (12:22 +0900)]
treewide: fix typos of SPDX-License-Identifier
Prior to the adoption of SPDX, it was difficult for tools to determine
the correct license due to incomplete or badly formatted license text.
The SPDX solves this issue, assuming people can correctly spell
"SPDX-License-Identifier" although this assumption is broken in some
places.
Since scripts/spdxcheck.py parses only lines that exactly matches to
the correct tag, it cannot (should not) detect this kind of error.
If the correct tag is missing, scripts/checkpatch.pl warns like this:
WARNING: Missing or malformed SPDX-License-Identifier tag in line *
So, people should notice it before the patch submission, but in reality
broken tags sometimes slip in. The checkpatch warning is not useful for
checking the committed files globally since large number of files still
have no SPDX tag.
Also, I am not sure about the legal effect when the SPDX tag is broken.
Anyway, these typos are absolutely worth fixing. It is pretty easy to
find suspicious lines by grep.
Paolo Bonzini [Fri, 31 May 2019 22:48:45 +0000 (00:48 +0200)]
Merge tag 'kvm-ppc-fixes-5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into kvm-master
PPC KVM fixes for 5.2
- Several bug fixes for the new XIVE-native code.
- Replace kvm->lock by other mutexes in several places where we hold a
vcpu mutex, to avoid lock order inversions.
- Fix a lockdep warning on guest entry for radix-mode guests.
- Fix a bug causing user-visible corruption of SPRG3 on the host.
John Pittman [Thu, 23 May 2019 21:49:39 +0000 (17:49 -0400)]
block: print offending values when cloned rq limits are exceeded
While troubleshooting issues where cloned request limits have been
exceeded, it is often beneficial to know the actual values that
have been breached. Print these values, assisting in ease of
identification of root cause of the breach.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: John Pittman <jpittman@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Linus Torvalds [Fri, 31 May 2019 20:49:50 +0000 (13:49 -0700)]
Merge tag 'v5.2-rc2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Four small smb3 fixes, one for stable"
* tag 'v5.2-rc2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: cifs_read_allocate_pages: don't iterate through whole page array on ENOMEM
dfs_cache: fix a wrong use of kfree in flush_cache_ent()
fs/cifs/smb2pdu.c: fix buffer free in SMB2_ioctl_free
cifs: fix memory leak of pneg_inbuf on -EOPNOTSUPP ioctl case
Pavel Machek [Sun, 26 May 2019 07:38:55 +0000 (09:38 +0200)]
leds: avoid flush_work in atomic context
It turns out that various triggers use led_blink_setup() from atomic
context, so we can't do a flush_work there. Flush is still needed for
slow LEDs, but we can move it to sysfs code where it is safe.
WARNING: inconsistent lock state
5.2.0-rc1 #1 Tainted: G W
--------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
swapper/1/0 [HC0[0]:SC1[1]:HE1:SE0] takes: 000000006e30541b
((work_completion)(&led_cdev->set_brightness_work)){+.?.}, at:
+__flush_work+0x3b/0x38a
{SOFTIRQ-ON-W} state was registered at:
lock_acquire+0x146/0x1a1
__flush_work+0x5b/0x38a
flush_work+0xb/0xd
led_blink_setup+0x1e/0xd3
led_blink_set+0x3f/0x44
tpt_trig_timer+0xdb/0x106
ieee80211_mod_tpt_led_trig+0xed/0x112
Fixes: 0db37915d912 ("leds: avoid races with workqueue") Signed-off-by: Pavel Machek <pavel@ucw.cz> Tested-by: Hugh Dickins <hughd@google.com> Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Linus Torvalds [Fri, 31 May 2019 18:08:44 +0000 (11:08 -0700)]
Merge branch 'next-fixes-for-5.2-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity
Pull integrity subsystem fixes from Mimi Zohar:
"Four bug fixes, none 5.2-specific, all marked for stable.
The first two are related to the architecture specific IMA policy
support. The other two patches, one is related to EVM signatures,
based on additional hash algorithms, and the other is related to
displaying the IMA policy"
* 'next-fixes-for-5.2-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
ima: show rules with IMA_INMASK correctly
evm: check hash algorithm passed to init_desc()
ima: fix wrong signed policy requirement when not appraising
x86/ima: Check EFI_RUNTIME_SERVICES before using
Linus Torvalds [Fri, 31 May 2019 17:53:34 +0000 (10:53 -0700)]
Merge tag 'for-linus-5.2b-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"One minor cleanup patch and a fix for handling of live migration when
running as Xen guest"
* tag 'for-linus-5.2b-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xenbus: Avoid deadlock during suspend due to open transactions
xen/pvcalls: Remove set but not used variable
Linus Torvalds [Fri, 31 May 2019 17:49:25 +0000 (10:49 -0700)]
Merge tag 's390-5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Heiko Carstens:
- Farewell Martin Schwidefsky: add Martin to CREDITS and remove him
from MAINTAINERS
- Vasily Gorbik and Christian Borntraeger join as maintainers for s390
- Fix locking bug in ctr(aes) and ctr(des) s390 specific ciphers
- A rather large patch which fixes gcm-aes-s390 scatter gather handling
- Fix zcrypt wrong dispatching for control domain CPRBs
- Fix assignment of bus resources in PCI code
- Fix structure definition for set PCI function
- Fix one compile error and one compile warning seen when
CONFIG_OPTIMIZE_INLINING is enabled
* tag 's390-5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
MAINTAINERS: add Vasily Gorbik and Christian Borntraeger for s390
MAINTAINERS: Farewell Martin Schwidefsky
s390/crypto: fix possible sleep during spinlock aquired
s390/crypto: fix gcm-aes-s390 selftest failures
s390/zcrypt: Fix wrong dispatching for control domain CPRBs
s390/pci: fix assignment of bus resources
s390/pci: fix struct definition for set PCI function
s390: mark __cpacf_check_opcode() and cpacf_query_func() as __always_inline
s390: add unreachable() to dump_fault_info() to fix -Wmaybe-uninitialized
Linus Torvalds [Fri, 31 May 2019 17:38:35 +0000 (10:38 -0700)]
Merge tag 'pm-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix three issues in the system-wide suspend and hibernation area
related to PCI device PM handling by suspend-to-idle, device wakeup
optimizations and arbitrary differences between suspend and
hiberantion.
Specifics:
- Modify the PCI bus type's PM code to avoid putting devices left by
their drivers in D0 on purpose during suspend to idle into
low-power states as doing that may confuse the system resume
callbacks of the drivers in question (Rafael Wysocki).
- Avoid checking ACPI wakeup configuration during system-wide suspend
for suspended devices that do not use ACPI-based wakeup to allow
them to stay in suspend more often (Rafael Wysocki).
- The last phase of hibernation is analogous to system-wide suspend
also because on platforms with ACPI it passes control to the
platform firmware to complete the transision, so make it indicate
that by calling pm_set_suspend_via_firmware() to allow the drivers
that care about this to do the right thing (Rafael Wysocki)"
* tag 'pm-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PCI: PM: Avoid possible suspend-to-idle issue
ACPI: PM: Call pm_set_suspend_via_firmware() during hibernation
ACPI/PCI: PM: Add missing wakeup.flags.valid checks
Linus Torvalds [Fri, 31 May 2019 15:34:32 +0000 (08:34 -0700)]
Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
Linus Torvalds [Fri, 31 May 2019 15:28:44 +0000 (08:28 -0700)]
Merge tag 'tty-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small serial and TTY driver fixes for 5.2-rc3.
Nothing major, just a number of fixes for reported issues. The fbcon
core fix also resolves an issue, and was acked by the relevant
maintainer to go through this tree.
All of these have been in linux-next with no reported issues"
* tag 'tty-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vt/fbcon: deinitialize resources in visual_init() after failed memory allocation
tty: max310x: Fix external crystal register setup
serial: sh-sci: disable DMA for uart_console
serial: imx: remove log spamming error message
tty: serial: msm_serial: Fix XON/XOFF
Linus Torvalds [Fri, 31 May 2019 15:16:31 +0000 (08:16 -0700)]
Merge tag 'usb-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some tiny USB fixes for a number of reported issues for
5.2-rc3.
Nothing huge here, just a small collection of xhci and other driver
bugs that syzbot has been finding in some drivers. There is also a
usbip fix and a fix for the usbip fix in here :)
All have been in linux-next with no reported issues"
* tag 'usb-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usbip: usbip_host: fix stub_dev lock context imbalance regression
media: smsusb: better handle optional alignment
xhci: Use %zu for printing size_t type
xhci: Convert xhci_handshake() to use readl_poll_timeout_atomic()
xhci: Fix immediate data transfer if buffer is already DMA mapped
usb: xhci: avoid null pointer deref when bos field is NULL
usb: xhci: Fix a potential null pointer dereference in xhci_debugfs_create_endpoint()
xhci: update bounce buffer with correct sg num
media: usb: siano: Fix false-positive "uninitialized variable" warning
USB: rio500: update Documentation
USB: rio500: simplify locking
USB: rio500: fix memory leak in close after disconnect
USB: rio500: refuse more than one device at a time
usbip: usbip_host: fix BUG: sleeping function called from invalid context
USB: sisusbvga: fix oops in error path of sisusb_probe
USB: Add LPM quirk for Surface Dock GigE adapter
media: usb: siano: Fix general protection fault in smsusb
usb: mtu3: fix up undefined reference to usb_debug_root
USB: Fix slab-out-of-bounds write in usb_get_bos_descriptor
Linus Torvalds [Fri, 31 May 2019 15:14:16 +0000 (08:14 -0700)]
Merge tag 'drm-fixes-2019-05-31' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Nothing too crazy, pretty quiet, maybe too quiet.
amdgpu:
- a fixed version of the raven firmware fix we previously reverted
- stolen memory fix
imx:
- regression fix
qxl:
- remove a bad warning
etnaviv:
- VM locking fix"
* tag 'drm-fixes-2019-05-31' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: reserve stollen vram for raven series
drm/etnaviv: lock MMU while dumping core
drm/imx: ipuv3-plane: fix atomic update status query for non-plus i.MX6Q
drm/qxl: drop WARN_ONCE()
drm/amd/display: Don't load DMCU for Raven 1 (v2)
Revert "lockd: Show pid of lockd for remote locks"
This reverts most of commit b8eee0e90f97 ("lockd: Show pid of lockd for
remote locks"), which caused remote locks to not be differentiated between
remote processes for NLM.
We retain the fixup for setting the client's fl_pid to a negative value.
Fixes: b8eee0e90f97 ("lockd: Show pid of lockd for remote locks") Cc: stable@vger.kernel.org Signed-off-by: Benjamin Coddington <bcodding@redhat.com> Reviewed-by: XueWei Zhang <xueweiz@google.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com>
1) Fix OOPS during nf_tables rule dump, from Florian Westphal.
2) Use after free in ip_vs_in, from Yue Haibing.
3) Fix various kTLS bugs (NULL deref during device removal resync,
netdev notification ignoring, etc.) From Jakub Kicinski.
4) Fix ipv6 redirects with VRF, from David Ahern.
5) Memory leak fix in igmpv3_del_delrec(), from Eric Dumazet.
6) Missing memory allocation failure check in ip6_ra_control(), from
Gen Zhang. And likewise fix ip_ra_control().
7) TX clean budget logic error in aquantia, from Igor Russkikh.
8) SKB leak in llc_build_and_send_ui_pkt(), from Eric Dumazet.
9) Double frees in mlx5, from Parav Pandit.
10) Fix lost MAC address in r8169 during PCI D3, from Heiner Kallweit.
11) Fix botched register access in mvpp2, from Antoine Tenart.
12) Use after free in napi_gro_frags(), from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (89 commits)
net: correct zerocopy refcnt with udp MSG_MORE
ethtool: Check for vlan etype or vlan tci when parsing flow_rule
net: don't clear sock->sk early to avoid trouble in strparser
net-gro: fix use-after-free read in napi_gro_frags()
net: dsa: tag_8021q: Create a stable binary format
net: dsa: tag_8021q: Change order of rx_vid setup
net: mvpp2: fix bad MVPP2_TXQ_SCHED_TOKEN_CNTR_REG queue value
ipv4: tcp_input: fix stack out of bounds when parsing TCP options.
mlxsw: spectrum: Prevent force of 56G
mlxsw: spectrum_acl: Avoid warning after identical rules insertion
net: dsa: mv88e6xxx: fix handling of upper half of STATS_TYPE_PORT
r8169: fix MAC address being lost in PCI D3
net: core: support XDP generic on stacked devices.
netvsc: unshare skb in VF rx handler
udp: Avoid post-GRO UDP checksum recalculation
net: phy: dp83867: Set up RGMII TX delay
net: phy: dp83867: do not call config_init twice
net: phy: dp83867: increase SGMII autoneg timer duration
net: phy: dp83867: fix speed 10 in sgmii mode
net: phy: marvell10g: report if the PHY fails to boot firmware
...
Linus Torvalds [Fri, 31 May 2019 04:05:23 +0000 (21:05 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The fixes are still trickling in for arm64, but the only really
significant one here is actually fixing a regression in the botched
module relocation range checking merged for -rc2.
Hopefully we've nailed it this time.
- Fix implementation of our set_personality() system call, which
wasn't being wrapped properly
- Fix system call function types to keep CFI happy
- Fix siginfo layout when delivering SIGKILL after a kernel fault
- Really fix module relocation range checking"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: use the correct function type for __arm64_sys_ni_syscall
arm64: use the correct function type in SYSCALL_DEFINE0
arm64: fix syscall_fn_t type
signal/arm64: Use force_sig not force_sig_fault for SIGKILL
arm64/module: revert to unsigned interpretation of ABS16/32 relocations
arm64: Fix the arm64_personality() syscall wrapper redirection
projects / mirror_ubuntu-hirsute-kernel.git / log