Arnd Bergmann [Fri, 18 Aug 2017 20:57:43 +0000 (22:57 +0200)]
Merge tag 'arm-soc/for-4.14/devicetree' of http://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.14" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs Device Tree changes for
4.14, please pull the following:
- Eric moves the bcm2837 DT file from arm64 to arm because it created a maintenance
problem and would have required either duplication or cross merges
- Stefan changes how the pinmuxing is defined and pushes it at the board level
to support Raspberry Pi Zero Wireless. He then adds supports for the actual
Raspberry Pi Zero Wireless board along with binding documentation. Stefan
also defines a proper SMP enable-method property and binding for BCM2836
(Raspbery Pi 2)
- Rafal describes the BCM5301X USB ports correctly in Device Tree such that
it becomes possible to assign them to specific LED triggers (e.g: USB activity).
He does the same thing for BCM53573 and defines default LED triggers for USB.
- Jon provides a fix for Northstar Plus which consists in correctly defining
the "dma-coherent" property for peripherals which are DMA coherent. He also
does a bit of re-arrangement of the USB DT nodes and finally adds USB 3 PHY
and host controller support for NorthStar Plus
- Florian adds support for Broadcom's BCM947189ACDBMR reference board which is
based on BCM47182/53573 and which supports external MoCA (BCM6802)
- Ray fixes the wrong UART2 base address for Cygnus
- Scott moves the v3d node in the proper unit address order and defines the correct
UART alias for the BCM91130_entphn reference board to be UART3
- Jason adds the DT node for the Cygnus Cortex-A9 Performance Monitoring Unit
- Jonathan adds a bunch of additional peripherals to the Cygnus DTS include file:
SDHCI, Keypad, SPI, DMA and pinmux configurations
- Raveendra adds the Cygnus OHCI and EHCI Device Tree nodes
* tag 'arm-soc/for-4.14/devicetree' of http://github.com/Broadcom/stblinux:
ARM: BCM53573: Specify ports for USB LED for Tenda AC9
ARM: dts: cygnus: Add generic-ehci/ohci nodes
ARM: dts: cygnus: add serial0 alias for uart3 on bcm91130_entphn
ARM: dts: cygnus: Add additional peripherals to dtsi
ARM: dts: cygnus: Enable Performance Monitoring Unit
ARM: dts: cygnus: place v3d in proper address ordered location
ARM: dts: cygnus: Fix incorrect UART2 register base
ARM: dts: bcm283x: Add 32-bit enable method for SMP
dt-bindings: arm: add SMP enable-method for BCM2836
ARM: dts: BCM53573: Add Broadcom BCM947189ACDBMR board support
ARM: dts: BCM5301X: Specify USB ports for USB LEDs of few devices
ARM: dts: NSP: Add USB3 and USB3 PHY to NSP
ARM: dts: NSP: Rearrage USB entries
ARM: dts: NSP: Add dma-coherent to relevant DT entries
ARM: dts: bcm2835: Add Raspberry Pi Zero W
dt-bindings: bcm: Add Raspberry Pi Zero W
ARM: bcm283x: Define UART pinmuxing on board level
ARM: dts: BCM5301X: Specify USB ports for each controller
ARM: dts: bcm283x: Move the BCM2837 DT contents from arm64 to arm.
Arnd Bergmann [Fri, 18 Aug 2017 20:55:20 +0000 (22:55 +0200)]
Merge tag 'omap-for-v4.14/dt-v3-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "device tree changes for omaps for v4.14, part2" from Tony Lindgren:
Second set of device tree changes for omaps for v4.14 merge window.
These got delayed a bit because the iodelay changes had to be
reworked for a missing Signed-off-by. And the beagleboard-x15
wants to use iodelay too for mmc:
- A series of changes to add dra7 iodelay data used for mmc
- Add support for new beagleBoard-x15 revision c
- Fix logicpd-torpedo-37xx-devkit mmc card detect direction
* tag 'omap-for-v4.14/dt-v3-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap3: logicpd-torpedo-37xx-devkit: Fix MMC1 cd-gpio
ARM: dts: am57xx-beagle-x15: Add support for rev C
ARM: dts: dra71-evm: Add pinmux configuration for MMC
ARM: dts: dra72-evm-revc: Add pinmux configuration for MMC
ARM: dts: dra72-evm: Add pinmux configuration for MMC
ARM: dts: am572x-idk: Add pinmux configuration for MMC
ARM: dts: am571x-idk: Add pinmux configuration for MMC
ARM: dts: am57xx-idk: Move common MMC/SD properties to common file
ARM: dts: am57xx-beagle-x15: Add pinmux configuration for MMC
ARM: dts: dra7-evm: Add pinmux configuration for MMC
ARM: dts: dra74x: Create a common file with MMC/SD IOdelay data
ARM: dts: dra72x: Create a common file with MMC/SD IOdelay data
Rafał Miłecki [Thu, 17 Aug 2017 09:05:14 +0000 (11:05 +0200)]
ARM: BCM53573: Specify ports for USB LED for Tenda AC9
This uses trigger-sources documented in commit 80dc6e1cd85fc ("dt-bindings:
leds: document new trigger-sources property") to specify USB ports. Such an
information can be used by operating system to setup LEDs behavior.
Jason Uy [Tue, 15 Aug 2017 17:26:00 +0000 (10:26 -0700)]
ARM: dts: cygnus: Enable Performance Monitoring Unit
Add PMU capability to Cygnus so trace and performance profiling
can be used.
Signed-off-by: Jason Uy <jason.uy@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Robert Nelson [Wed, 16 Aug 2017 16:50:53 +0000 (11:50 -0500)]
ARM: dts: am57xx-beagle-x15: Add support for rev C
Latest update to the BeagleBoard-X15 platform (revision C). This board contains
a silicon update (Rev 2.0), which includes a fix for the 2nd ethernet phy when
running at 1000 Mbps speeds.
This board can be indentified by the [C.00] after [BBRDX15_] in the at24 eeprom:
[BBRDX15_C.001731PX150249]
Rev C is now in full production and boards are available for end users.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tony Lindgren <tony@atomide.com> CC: Nishanth Menon <nm@ti.com> CC: Lokesh Vutla <lokeshvutla@ti.com> CC: Kishon Vijay Abraham I <kishon@ti.com> CC: Jason Kridner <jkridner@beagleboard.org> CC: Drew Fustini <drew@beagleboard.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Arnd Bergmann [Thu, 17 Aug 2017 08:58:50 +0000 (10:58 +0200)]
Merge tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Pull "Amlogic 32-bit DT changes for v4.14" from Kevin Hilman:
- update clock controler for use as reset controller
- misc. updates/fixups/improvements
* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson6: use stable UART bindings
ARM: dts: meson: mark the clock controller also as reset controller
ARM: dts: meson: add a node which describes the SRAM
ARM: dts: meson8b: use the existing wdt node to override the compatible
ARM: dts: meson8: add the PWM controller nodes
ARM: dts: move the pwm_ab and pwm_cd nodes to meson.dtsi
Arnd Bergmann [Thu, 17 Aug 2017 08:56:37 +0000 (10:56 +0200)]
Merge tag 'keystone_dts_for_4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt
Pull "ARM: Keystone DTS for 4.14" from Santosh Shilimkar:
Contents:
- ti-sci power domain, clock and reset controller support
- DSP nodes for k2h/k2l/k2e evms
- DSP CMA memory pools for k2h/k2l/k2e/keg evms
- MMC/hsmmc suport for k2g
- eDMA support for k2g
- DCAN support for k2g
* tag 'keystone_dts_for_4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone: (22 commits)
ARM: dts: keystone-k2g-ice: Add and enable DSP CMA memory pool
ARM: dts: keystone-k2g-evm: Add and enable DSP CMA memory pool
ARM: dts: keystone-k2g: Add DSP node
ARM: dts: k2g: Add DCAN nodes
dt-bindings: net: c_can: Update binding for clock and power-domains property
ARM: dts: keystone-k2g-evm: Enable MMC0 and MMC1
ARM: dts: keystone-k2g: add MMC0 and MMC1 nodes
ARM: dts: keystone-k2g: Add eDMA nodes
dt-bindings: ti,omap-hsmmc: Add 66AK2G mmc controller
dt-bindings: ti,edma: Add 66AK2G specific information
ARM: dts: keystone-k2g: Add gpio nodes
ARM: dts: keystone-k2e-evm: Add and enable DSP CMA memory pool
ARM: dts: keystone-k2l-evm: Add and enable common DSP CMA memory pool
ARM: dts: keystone-k2hk-evm: Add and enable common DSP CMA memory pool
ARM: dts: keystone-k2e: Add DSP node
ARM: dts: keystone-k2l: Add DSP nodes
ARM: dts: keystone-k2hk: Add DSP nodes
ARM: dts: keystone-k2g: Add TI SCI reset-controller node
ARM: dts: keystone-k2g: Add ti-sci clock provider node
ARM: dts: keystone-k2g: Add ti-sci power domain node
...
Arnd Bergmann [Wed, 16 Aug 2017 21:32:28 +0000 (23:32 +0200)]
Merge tag 'qcom-dts-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt
Pull "Qualcomm Device Tree Changes for v4.14" from Andy Gross:
* Fixup XO, timer nodes, and pinctrl on IPQ4019
* Add IPQ4019 RNG and wifi blocks
* Update MSM8974 coresight node
* Add IPQ8074 bindings
* tag 'qcom-dts-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: dts: qcom: add and enable both wifi blocks on the IPQ4019
ARM: dts: qcom-msm8974: dts: Update coresight replicator
ARM: dts: qcom: add pseudo random number generator on the IPQ4019
ARM: dts: ipq4019: Move xo and timer nodes to SoC dtsi
ARM: dts: ipq4019: Fix pinctrl node name
dt-bindings: qcom: Add IPQ8074 bindings
Arnd Bergmann [Wed, 16 Aug 2017 21:12:39 +0000 (23:12 +0200)]
Merge tag 'gemini-dts-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Pull "Gemini DTS updates for ARM SoC take one" from Linus Walleij:
* tag 'gemini-dts-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: gemini: add pin control set-up for the SoC
ARM: dts: Add DTS file for D-Link DIR-685
ARM: dts: gemini: Switch to using macros
Arnd Bergmann [Wed, 16 Aug 2017 21:07:06 +0000 (23:07 +0200)]
Merge tag 'v4.14-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "Rockchip dts32 changes for 4.14" from Heiko Stübner:
Removal of the deprectated num-slots property from all Rockchip dw-mmc
nodes. The rv1108 gains support for sd-cards on the evaluation board and
the general nodes get a bit of cosmetic. On rk3288 the evb gains support
saradc and the adc-key connected to it while some more boards also get
their mali gpu enabled (fennec, evb, tinker).
The biggest set of changes can be found on the rk3228/rk3229 combo this
time. It gets core support for efuse, sdmmc, sdio, io-domans and spdif
as well as a separate rk3229.dtsi that will keep the slight differences
between the two brothers rk3228/rk3229. The evaluation board also gets
some attention and abled nodes (regulators, io-domains, emmc, tsadc keys)
But I think the most interesting change is the cpu enable-method for it.
Instead of using the older in-kernel method, we're now also moving to
handling this in firmware via the psci interface on 32bit Rockchip socs.
In a recently merged pull request [0] support for the rk3228/rk3229 was
added to OP-TEE including the psci support and it seems supporting other
32bit Rockchip socs that way is also planned for the future.
[0] https://github.com/OP-TEE/optee_os/pull/1666
* tag 'v4.14-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (23 commits)
ARM: dts: rockchip: fix property-ordering in rv1108 mmc nodes
ARM: dts: rockchip: enable sdmmc for rv1108 evb
ARM: dts: rockchip: add efuse device node for rk3228
ARM: dts: rockchip: add gpio power-key for rk3229-evb
ARM: dts: rockchip: enable tsadc for rk3229-evb
ARM: dts: rockchip: enable eMMC for rk3229-evb
ARM: dts: rockchip: enable io-domain for rk3229-evb
ARM: dts: rockchip: add cpu-supply property for cpu node of rk3229-evb
ARM: dts: rockchip: add regulator nodes for rk3229-evb
ARM: dts: rockchip: add sdmmc and sdio nodes for rk3228 SoC
ARM: dts: rockchip: fix compatible string for eMMC node of rk3228 SoC
ARM: dts: rockchip: add cpu enable method for rk3228 SoC
ARM: dts: rockchip: remove num-slots from all platforms
ARM: dts: rockchip: Add io-domain node for rk3228
ARM: dts: rockchip: add basic dtsi file for RK3229 SoC
ARM: dts: rockchip: enable adc key for rk3288-evb
ARM: dts: rockchip: enable saradc for rk3288-evb
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-fennec
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-evb
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-tinker
...
Arnd Bergmann [Wed, 16 Aug 2017 21:05:39 +0000 (23:05 +0200)]
Merge tag 'renesas-dt-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Updates for v4.14" from Simon Horman:
Changes of note:
* Add pin controller support to the RZ/G1M (r8a7743) SoC and
RZ/A1 (r7s72100) SoCs now that the driver is available in v4.13-rc1.
* Add GPIO support to the RZ/G1M (r8a7743) SoC now that the driver
is availabe in v4.13-rc1.
* Enable MMCIF0 and Ethernet AVB support on the RZ/G1M (r8a7743) SoC and
the iWave-RZG1M-20M Qseven SOM. This depends on newly added pin
controller support noted above.
* Use R-Car Gen 2 fallback binding for vin nodes
This makes binding use consistent across R-Car Gen 2 SoCs.
It does not have any run-time effect
* Use SMP jump stub SRAM region from DT on R-Car Gen 2 SoCs
Geert Uytterhoeven says, "The R-Car Gen2 platform code for CPU core
bringup needs to copy a jump stub to on-SoC SRAM. Currently it uses a
hardcoded address pointing to ICRAM1."
* Add Inter Connect RAM to R-Car Gen 2 and RZ/G1 SoCs
Geert Uytterhoeven says, "R-Car Gen2 and RZ/G1 SoCs contain two or three
blocks of SRAM, which can be used for several purposes. One such purpose
is holding a jump stub for CPU core bringup."
* Use generic compatible string for I2C EEPROM for RZ/A1 (r7s72100) SoC
and koelsch board.
This is part of a tree-wide cleanup by Javier Martinez Canillas
* tag 'renesas-dt-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (38 commits)
ARM: dts: iwg20m: Correct indentation of mmcif0 properties
ARM: dts: rskrza1: Add LED0 pin support
ARM: dts: rskrza1: Add SDHI1 pin group
ARM: dts: rskrza1: Add Ethernet pin group
ARM: dts: rskrza1: Add SCIF2 pin group
ARM: dts: genmai: Add ethernet pin group
ARM: dts: genmai: Add user led device nodes
ARM: dts: genmai: Add RIIC2 pin group
ARM: dts: genmai: Add SCIF2 pin group
ARM: dts: r7s72100: Add pin controller node
ARM: dts: iwg20m: Add MMCIF0 support
ARM: dts: r8a7794: Use R-Car Gen 2 fallback binding for vin nodes
ARM: dts: r8a7791: Use R-Car Gen 2 fallback binding for vin nodes
ARM: dts: r8a7790: Use R-Car Gen 2 fallback binding for vin nodes
ARM: dts: r8a7743: Add MMCIF0 support
ARM: dts: r8a7794: Reserve SRAM for the SMP jump stub
ARM: dts: r8a7793: Reserve SRAM for the SMP jump stub
ARM: dts: r8a7792: Reserve SRAM for the SMP jump stub
ARM: dts: r8a7791: Reserve SRAM for the SMP jump stub
ARM: dts: r8a7790: Reserve SRAM for the SMP jump stub
...
Arnd Bergmann [Wed, 16 Aug 2017 21:04:23 +0000 (23:04 +0200)]
Merge tag 'renesas-dt-bindings-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Bindings Updates for v4.14" from Simon Horman:
* Document R-Car D3 (r8a77995) SoC and Draak board
* Document reserved SRAM for the SMP jump stub on R-Car Gen2 and RZ/G1 SoCs
Geert Uytterhoeven says, "+Renesas R-Car Gen2 and RZ/G1 SoCs need a small
piece of SRAM for the jump stub +for secondary CPU bringup and CPU
hotplug. +This memory is reserved by adding a child node to a
"mmio-sram" node..."
* Add a VSP channel index to DU vsps
Laurent Pinchart says, "multiple LIF instances in the VSP. The current DT
bindings don't support specifying that kind of SoC integration scheme.
Extend them with a VSP channel index."
* Add R-Car M3-W (r8a7796) HDMI TX DT bindings
This is compatible with existing R-Car H3 (r8a7795) support
* tag 'renesas-dt-bindings-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Document Renesas Draak board DT bindings
ARM: shmobile: Document R-Car D3 SoC DT bindings
dt-bindings: display: rcar-du: Add a VSP channel index to the vsps DT property
dt-bindings: sram: Document renesas,smp-sram
dt-bindings: display: renesas: Add R-Car M3-W HDMI TX DT bindings
Arnd Bergmann [Wed, 16 Aug 2017 21:00:53 +0000 (23:00 +0200)]
Merge tag 'stm32-dt-for-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into next/dt
Pull "STM32 DT updates for v4.14, round 1" from Alexandre Torgue:
Highlights:
----------
-Add DMA support on STM32F746
-Add DMA support on STM32H743
-Add DAC support on STM32H743
-Add DAC support on STM32F429
-Add ADC support on STM32H743
-Enable ADC on stm32h743i-eval board
-Add CEC support on STM32F7xx MCUs
-Enable CEC on stm32f769-disco board
-Remove rdinit from stm32f4 boards
* tag 'stm32-dt-for-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Add DMA support for STM32H743 SoC
ARM: dts: stm32: Add DMA support for STM32F746 SoC
ARM: dts: stm32: enable ADC on stm32h743i-eval board
ARM: dts: stm32: add ADC support on stm32h743
ARM: dts: stm32: Add DAC support on stm32h743
ARM: dts: stm32: Add DAC support on stm32f429
ARM: dts: stm32: enable CEC for stm32f769 discovery
ARM: dts: stm32: add CEC for stm32f7 family
ARM: dts: stm32: reorder stm32h743 nodes
ARM: dts: stm32: Remove rdinit from bootargs on stm32f429-disco
ARM: dts: stm32: Remove rdinit from bootargs on stm32f429i-eval
ARM: dts: stm32: Remove rdinit from bootargs on stm32f469-disco
Arnd Bergmann [Wed, 16 Aug 2017 20:54:36 +0000 (22:54 +0200)]
Merge tag 'samsung-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Samsung DTS ARM changes for v4.13" from Krzysztof Kozłowski:
Remove deprecated and unneeded properties from Exynos boards.
* tag 'samsung-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Remove num-slots from exynos platforms
ARM: dts: exynos: Remove the OF graph from DSI node
ARM: dts: dra71-evm: Add pinmux configuration for MMC
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra71-evm.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: dra72-evm-revc: Add pinmux configuration for MMC
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra72-evm-revc.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: dra72-evm: Add pinmux configuration for MMC
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra72-evm.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am572x-idk: Add pinmux configuration for MMC
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74x SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am572x-idk.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am571x-idk: Add pinmux configuration for MMC
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am571x-idk.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am57xx-beagle-x15: Add pinmux configuration for MMC
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am57xx-beagle-x15/am57xx-beagle-x15-revb1.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: dra7-evm: Add pinmux configuration for MMC
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra7-evm.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Add NAND controller node to LD4, Pro4, sLD8, Pro5, and PXs2.
Set up pinctrl to enable 2 chip select lines except Pro4. The CS1
for Pro4 is multiplexed with other peripherals such as UART2, so
I did not enable it.
Lokesh Vutla [Sat, 12 Aug 2017 04:06:05 +0000 (09:36 +0530)]
ARM: dts: Add support for dra76-evm
dra76-evm is a board based on TI's dra76 processor targeting
for infotainment systems. Adding support for this platform.
dra76-evm and dra7-evm has a similar layout except with few differences.
So create a dra7-evm-common.dtsi with similarities on dra76-evm and
dra7-evm. Include this common dtsi in both dra7-evm.dts and dra76-evm.dts
Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Lokesh Vutla [Sat, 12 Aug 2017 04:06:04 +0000 (09:36 +0530)]
ARM: dts: Add support for dra76x family of devices
dra76 family is a high-performance, infotainment application
device, based on OMAP architecture on a 28-nm technology.
This contains most of the subsystems, peripherals that are
available on dra74, dra72 family. This SoC mainly features
Subsystems:
- 2 x Cortex-A15 with max speed of 1.8GHz
- 2 X DSP
- 2 X Cortex-M4 IPU
- ISS
- CAL
- DSS
- VPE
- VIP
Connectivity peripherals:
- 1 USB3.0 and 3 USB2.0 subsystems
- 2 x SATA
- 2 x PCI Express Gen2
- 3-port Gigabit ethernet switch
- 2 x CAN
- MCAN
Adding basic dts support for DRA76 family while reusing the
data available in dra7.dtsi, dra74x.dtsi.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pcie1 dt node in order for the controller to operate in
endpoint mode. However since none of the dra7 based boards have
slots configured to operate in endpoint mode, keep EP mode
disabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
SZ Lin [Wed, 2 Aug 2017 06:57:57 +0000 (14:57 +0800)]
ARM: dts: am335x: add support for Moxa UC-8100-ME-T open platform
Add support for Moxa UC-8100-ME-T open platform
The UC-8100-ME-T computing platform is designed
for embedded data acquisition industrial applications
The features of UC-8100-ME-T series are:
* eMMC
* SPI flash
* SD slot
* 2x LAN
* 2 RS-232/422/485 ports, software-selectable
* Mini PCIe form factor with USB signal
* USB host
* EEPROM
* TPM
* Watchdog
* RTC
* User gpio-keys
* User LEDs
* User button
Signed-off-by: SZ Lin <sz.lin@moxa.com> Acked-by: Rob Herring <robh@kernel.org>
[tony@atomide.com: fix unit adress as suggested by Rob] Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: dra7xx: Enable NAND dma prefetch by default
Currently the default method of prefetch polled shows the highest
possible read and write speed when minimal non NAND background
activity is being done. But it is also very CPU intensive to reach
these high speeds (CPU load of 99% via mtd performance tests). While
DMA prefetch only uses 50% of the CPU to achieve around 23% less in
top read and write performance.
However, as the non NAND CPU load increases the read and write
performance takes a large hit when using polled prefetch. Therefore,
prefetch dma mode ends up outperforming prefetch polled in general
"system level" test. So switch to using dma prefetch by default since
it is likely what most users would prefer.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am437xx: Enable NAND dma prefetch by default
Currently the default method of prefetch polled shows the highest
possible read and write speed when minimal non NAND background
activity is being done. But it is also very CPU intensive to reach
these high speeds (CPU load of 99% via mtd performance tests). While
DMA prefetch only uses 50% of the CPU to achieve around 23% less in
top read and write performance.
However, as the non NAND CPU load increases the read and write
performance takes a large hit when using polled prefetch. Therefore,
prefetch dma mode ends up outperforming prefetch polled in general
"system level" test. So switch to using dma prefetch by default since
it is likely what most users would prefer.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am335x-evm: Enable NAND dma prefetch by default
Currently the default method of prefetch polled shows the highest
possible read and write speed when minimal non NAND background
activity is being done. But it is also very CPU intensive to reach
these high speeds (CPU load of 99% via mtd performance tests). While
DMA prefetch only uses 50% of the CPU to achieve around 23% less in
top read and write performance.
However, as the non NAND CPU load increases the read and write
performance takes a large hit when using polled prefetch. Therefore,
prefetch dma mode ends up outperforming prefetch polled in general
"system level" test. So switch to using dma prefetch by default since
it is likely what most users would prefer.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
All nodes inhert "interrupt-parent" property from root
node. Removed the aforementioned property from usbhsohci,
usbhsehci, ssi_port1, ssi_port2 nodes to avoid duplication.
Signed-off-by: Karthik Tummala <karthik@techveda.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Tue, 27 Jun 2017 08:58:32 +0000 (01:58 -0700)]
ARM: dts: Disable HDMI CEC internal pull-ups
Devices using an external encoder, ESD protection and level shifter
such as tpd12s015 or ip4791cz12 have the CEC pull in the encoder
chip. And on var-som-om44, there is external pull up resistor R30.
So the internal CEC pull-up resistor needs to be disabled as otherwise
the external and internal pull are parallel making the pull value
much smaller than intended. This leads into the CEC not working as
reported by Hans Verkuil <hverkuil@xs4all.nl>.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl> Cc: Dmitry Lifshitz <lifshitz@compulab.co.il> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Stefan Wahren [Sun, 6 Aug 2017 15:28:10 +0000 (17:28 +0200)]
ARM: dts: bcm283x: Add 32-bit enable method for SMP
This patch adds the missing 32-bit enable method for SMP on BCM2836 and
BCM2837. The BCM2837 already has an enabled method, but this one only
works for 64-bit.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Tested-by: Eric Anholt <eric@anholt.net>
Suman Anna [Sat, 12 Aug 2017 17:58:11 +0000 (10:58 -0700)]
ARM: dts: keystone-k2g-ice: Add and enable DSP CMA memory pool
A CMA memory pool reserved memory node is added, and is attached
to the DSP node through the 'memory-region' property on the K2G
ICE board. This area will be used for allocating virtio rings and
buffers. This node allows the DSP Memory Protection and Address
Extension (MPAX) module to be configured properly for the DSP
processor, and matches the values used on the other Keystone 2
boards for software compatibility.
The reserved memory node and the user DSP node are also marked
okay to enable the DSP on the K2G ICE board.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Andrew F. Davis [Sat, 12 Aug 2017 17:58:10 +0000 (10:58 -0700)]
ARM: dts: keystone-k2g-evm: Add and enable DSP CMA memory pool
A CMA memory pool reserved memory node is added, and is attached
to the DSP node through the 'memory-region' property on the K2G
EVM board. This area will be used for allocating virtio rings and
buffers. This node allows the DSP Memory Protection and Address
Extension (MPAX) module to be configured properly for the DSP
processor, and matches the values used on the other Keystone 2
boards for software compatibility.
The reserved memory node and the user DSP node are also marked
okay to enable the DSP on the 66AK2G EVM board.
Signed-off-by: Andrew F. Davis <afd@ti.com> Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Suman Anna [Sat, 12 Aug 2017 17:58:10 +0000 (10:58 -0700)]
ARM: dts: keystone-k2g: Add DSP node
The Keystone 2 66AK2G SoC has a single TMS320C66x DSP Core
Subsystem (C66x CorePac), containing a C66x Fixed/Floating-Point
DSP Core, and 32 KB of L1P & L1D SRAMs and a 1 MB L2 SRAM. Add
the DT node for this DSP processor sub-system.
The DT node has a new property 'power-domains' and no 'clocks'
properties, and uses slightly different property values for
'resets' compared to other Keystone 2 SoCs. The processor does
not have an MMU, and uses various IPC Generation registers and
shared memory for inter-processor communication. The alias with
a stem 'rproc' has also been added for the DSP, it provides a
fixed remoteproc id for the DSP processor.
Signed-off-by: Andrew F. Davis <afd@ti.com> Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Lokesh Vutla [Thu, 10 Aug 2017 16:50:15 +0000 (09:50 -0700)]
ARM: dts: k2g: Add DCAN nodes
Add nodes for the two DCAN instances included in 66AK2G
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[d-gerlach@ti.com: add power-domains and clock information] Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[fcooper@ti.com: update subject and commit message. Misc minor updates] Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
dt-bindings: net: c_can: Update binding for clock and power-domains property
CAN driver uses the clk_get_rate call to determine the frequency of the
functional clock. OMAP based SoCs do not require the clock property since
hwmod already handles creating a "fck" clock thats accessible to drivers.
However, this isn't the case for 66AK2G which makes the clocks property
require for that SoC.
66AK2G requires a new property. Therefore, update the binding to also make
this property requirement clear. Also clarify that for OMAP based SoCs
ti,hwmod is a required property.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
ARM: dts: tps65217: Add power button interrupt to the common tps65217.dtsi file
The interrupt for power button is static data that comes from the
datasheet, there is no reason to need to define this value on every
board so seams reasonable put this information into the common tps65217
file.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: tps65217: Add charger interrupts to the common tps65217.dtsi file
The interrupt specifiers for USB and AC charger input are static data that
comes from the datasheet, there is no reason to need to define these values
on every board so seem reasonable put this information into the common
tps65217 file.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Neil Armstrong [Wed, 21 Jun 2017 14:42:12 +0000 (16:42 +0200)]
ARM: dts: meson6: use stable UART bindings
The UART bindings needs specifying a SoC family, use the meson6 family
for the UART nodes like the other nodes.
Switch to the stable UART bindings for meson6 by adding a XTAL node and
using the proper compatible strings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
ARM: dts: qcom: add pseudo random number generator on the IPQ4019
This architecture has a pseudo random number generator
supported by the existing "qcom,prng" binding.
rngtest: bits received from input: 5795960032
rngtest: FIPS 140-2 successes: 289591
rngtest: FIPS 140-2 failures: 207
rngtest: FIPS 140-2(2001-10-10) Monobit: 25
rngtest: FIPS 140-2(2001-10-10) Poker: 28
rngtest: FIPS 140-2(2001-10-10) Runs: 91
rngtest: FIPS 140-2(2001-10-10) Long run: 67
rngtest: FIPS 140-2(2001-10-10) Continuous run: 0
rngtest: input channel speed: (min=244; avg=46122; max=3906250)Kibits/s
rngtest: FIPS tests speed: (min=1.327; avg=20.966; max=26.345)Mibits/s
rngtest: Program run time: 386965827 microseconds
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds a device tree file for the Gemini-based D-Link DIR-685
router, supporting all devices that are currently supported in
the main DTSI SoC file.
ARM: dts: BCM53573: Add Broadcom BCM947189ACDBMR board support
Adds support for the Broadcom reference board BCM947189ACDMBR which
features the following:
* 128MB of DRAM
* External MoCA support through a Broadcom BCM6802 chip
* 1x external Gigabit PHY through the external BCM6802
* 1x USB 2.0 port
* 1x PCIE slot
* Few configurable buttons and LEDs
Rafał Miłecki [Wed, 2 Aug 2017 04:40:41 +0000 (06:40 +0200)]
ARM: dts: BCM5301X: Specify USB ports for USB LEDs of few devices
This uses trigger-sources documented in commit 80dc6e1cd85fc ("dt-bindings:
leds: document new trigger-sources property") to specify USB ports. Such an
information can be used by operating system to setup LEDs behavior.
I updated dts files for 7 devices I own and I was able to test.
Jon Mason [Mon, 31 Jul 2017 21:54:21 +0000 (17:54 -0400)]
ARM: dts: NSP: Add dma-coherent to relevant DT entries
Cache related issues with DMA rings and performance issues related to
caching are being caused by not properly setting the "dma-coherent" flag
in the device tree entries. Adding it here to correct the issue.
Signed-off-by: Jon Mason <jon.mason@broadcom.com> Fixes: 3107fa5bcfb2 ("ARM: dts: NSP: Add SD/MMC support") Fixes: 13d04f20935c ("ARM: dts: NSP: Add AMAC entries") Fixes: 5aeda7bf8a1e ("ARM: dts: NSP: Add and enable amac2") Fixes: 17d517172300 ("ARM: dts: NSP: Add mailbox (PDC) to NSP") Fixes: 1d8ece6639e1 ("ARM: dts: NSP: Add EHCI/OHCI USB nodes to device tree") Fixes: 0f9f27a36d09 ("ARM: dts: NSP: Add I2C support to the DT") Fixes: 8dbcad020f2e ("ARM: dts: nsp: Add sata device tree entry") Fixes: 522199029fdc ("ARM: dts: NSP: Fix PCIE DT issue") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Update the ti,omap-hsmmc.txt to include information about
66AK2G specific mmc controller. Also cleanup the entries
under optional properties to look a bit nicer.
Keerthy [Mon, 7 Aug 2017 13:22:29 +0000 (06:22 -0700)]
ARM: dts: keystone-k2g: Add gpio nodes
66AK2G has 2 instances of gpio. The first one has all the 144 GPIOs
functional. 9 banks with 16 gpios making a total of 144. The second
instance has only the GPIO0:GPIO67 functional and rest are marked
reserved.
Linus Torvalds [Sun, 6 Aug 2017 23:11:34 +0000 (16:11 -0700)]
Merge tag 'platform-drivers-x86-v4.13-4' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fix from Darren Hart:
"Fix loop preventing some platforms from waking up via the power button
in s2idle:
- intel-vbtn: match power button on press rather than release"
* tag 'platform-drivers-x86-v4.13-4' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: intel-vbtn: match power button on press rather than release
Linus Torvalds [Sun, 6 Aug 2017 19:31:17 +0000 (12:31 -0700)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"A large number of ext4 bug fixes and cleanups for v4.13"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix copy paste error in ext4_swap_extents()
ext4: fix overflow caused by missing cast in ext4_resize_fs()
ext4, project: expand inode extra size if possible
ext4: cleanup ext4_expand_extra_isize_ea()
ext4: restructure ext4_expand_extra_isize
ext4: fix forgetten xattr lock protection in ext4_expand_extra_isize
ext4: make xattr inode reads faster
ext4: inplace xattr block update fails to deduplicate blocks
ext4: remove unused mode parameter
ext4: fix warning about stack corruption
ext4: fix dir_nlink behaviour
ext4: silence array overflow warning
ext4: fix SEEK_HOLE/SEEK_DATA for blocksize < pagesize
ext4: release discard bio after sending discard commands
ext4: convert swap_inode_data() over to use swap() on most of the fields
ext4: error should be cleared if ea_inode isn't added to the cache
ext4: Don't clear SGID when inheriting ACLs
ext4: preserve i_mode if __ext4_set_acl() fails
ext4: remove unused metadata accounting variables
ext4: correct comment references to ext4_ext_direct_IO()
Linus Torvalds [Sun, 6 Aug 2017 18:52:01 +0000 (11:52 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"This fixes two build issues for ralink platforms, both due to missing
#includes which used to be included indirectly via other headers"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: ralink: mt7620: Add missing header
MIPS: ralink: Fix build error due to missing header
Dmitry V. Levin [Sat, 5 Aug 2017 20:00:50 +0000 (23:00 +0300)]
Fix compat_sys_sigpending breakage
The latest change of compat_sys_sigpending in commit 8f13621abced
("sigpending(): move compat to native") has broken it in two ways.
First, it tries to write 4 bytes more than userspace expects:
sizeof(old_sigset_t) == sizeof(long) == 8 instead of
sizeof(compat_old_sigset_t) == sizeof(u32) == 4.
Second, on big endian architectures these bytes are being written in the
wrong order.
This bug was found by strace test suite.
Reported-by: Anatoly Pugachev <matorola@gmail.com> Inspired-by: Eugene Syromyatnikov <evgsyr@gmail.com> Fixes: 8f13621abced ("sigpending(): move compat to native") Signed-off-by: Dmitry V. Levin <ldv@altlinux.org> Acked-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jerry Lee [Sun, 6 Aug 2017 05:18:31 +0000 (01:18 -0400)]
ext4: fix overflow caused by missing cast in ext4_resize_fs()
On a 32-bit platform, the value of n_blcoks_count may be wrong during
the file system is resized to size larger than 2^32 blocks. This may
caused the superblock being corrupted with zero blocks count.
Fixes: 1c6bd7173d66 Signed-off-by: Jerry Lee <jerrylee@qnap.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@vger.kernel.org # 3.7+
Miao Xie [Sun, 6 Aug 2017 05:00:49 +0000 (01:00 -0400)]
ext4, project: expand inode extra size if possible
When upgrading from old format, try to set project id
to old file first time, it will return EOVERFLOW, but if
that file is dirtied(touch etc), changing project id will
be allowed, this might be confusing for users, we could
try to expand @i_extra_isize here too.
Reported-by: Zhang Yi <yi.zhang@huawei.com> Signed-off-by: Miao Xie <miaoxie@huawei.com> Signed-off-by: Wang Shilong <wshilong@ddn.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Miao Xie [Sun, 6 Aug 2017 04:40:01 +0000 (00:40 -0400)]
ext4: restructure ext4_expand_extra_isize
Current ext4_expand_extra_isize just tries to expand extra isize, if
someone is holding xattr lock or some check fails, it will give up.
So rename its name to ext4_try_to_expand_extra_isize.
Besides that, we clean up unnecessary check and move some relative checks
into it.
Miao Xie [Sun, 6 Aug 2017 04:27:38 +0000 (00:27 -0400)]
ext4: fix forgetten xattr lock protection in ext4_expand_extra_isize
We should avoid the contention between the i_extra_isize update and
the inline data insertion, so move the xattr trylock in front of
i_extra_isize update.
Signed-off-by: Miao Xie <miaoxie@huawei.com> Reviewed-by: Wang Shilong <wshilong@ddn.com>
projects / mirror_ubuntu-focal-kernel.git / log